Canon Pixma mg8120 SM PC PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 81

PIXMA MG8120

SERVICE
MANUAL

Canon
Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
MG8100 series

INTRODUCTION

[ How to use this Service Manual ]


This manual is intended to solve printer problems smoothly, with each section representing the typical service
procedures, as shown below.

Troubleshooting Identify the problem, and handle it accordingly.

Repair When a part needs to be replaced, see this section.

Adjustment &
After repair, perform the necessary adjustment and settings.
Settings

At the end of the servicing, verify the machine following the inspection flow in this
Verification
section.

Appendix Information that will be necessary for maintenance and repair of the machine

For reference:
This manual does not provide sufficient information for disassembly and reassembly procedures. Refer to the
graphics in the separate Parts Catalog.

<INTRODUCTION>
MG8100 series

TABLE OF CONTENTS

1. TROUBLESHOOTING
1-1. Troubleshooting by Symptom
1-2. Operator Call Error Troubleshooting
1-3. Service Call Error Troubleshooting

2. REPAIR
2-1. Major Replacement Parts and Adjustment
2-2. Part Replacement Procedures
(1) External housing, scanner unit, and document cover removal
(2) Operation panel removal
(3) Cable wiring and connection
(4) Document window R removal
(5) Carriage unlocking
(6) ASF unit removal
(7) Carriage unit removal
(8) Spur unit and platen unit removal
(9) Purge drive system unit (right plate) and switch system unit (left plate) removal
(10) Engine unit reassembly
(11) Ink absorber replacement

3. ADJUSTMENT / SETTINGS
3-1. Adjustment
3-2. Adjustment and Maintenance in User Mode
3-3. Adjustment and Settings in Service Mode
(1) Service mode operation procedures
(2) Service Tool functions
(3) LF / Eject correction (automatic / manual)
(4) Button and LCD test
(5) Ink absorber counter setting
(6) N/A
(7) Capacitive sensor sensitivity setting
3-4. Grease Application
3-5. Special Notes on Servicing
(1) For smeared printing, uneven printing, or non-ejection of ink
(2) Paper feed motor adjustment
(3) Carriage unit replacement
(4) Document pressure sheet (sponge sheet) replacement
(5) Ink absorber counter setting
(6) Preventive replacement of ink absorber

4. VERIFICATION AFTER REPAIR


4-1. Standard Inspection Flow
4-2. Integrated Inspection Pattern Print
4-3. Ink Absorber Counter Value Print

5. APPENDIX
5-1. Customer Maintenance
5-2. Special Tools
5-3. Sensors
5-4. Serial Number Location

6. MACHINE TRANSPORTATION

<TABLE OF CONTENTS>
MG8100 series TABLE OF CONTENTS

1. TROUBLESHOOTING

1-1. Troubleshooting by Symptom


Symptom Solution
Faulty operation The power does not turn on. (1) Confirm cable connection:
The power turns off - DC harness ass'y
immediately after power-on. - Power switch harness ass'y
=> No incomplete connection, cable
breakage, or cable caught in units
(2) Replace the following item(s):
- Logic board ass'y
- AC adapter
- DC harness ass'y
- Power switch harness ass'y
- Document top cover unit
A strange noise occurs. (1) Examine and remove any foreign material
from the drive portions.
(2) Replace the following item(s):
- The part generating the strange noise
- Logic board ass'y
The LCD does not display (1) Confirm cable connection:
properly. - LCD FFC
A portion of the LCD is not - Panel FFC
displayed. => No incomplete connection, cable
The display flickers. breakage, or cable caught in units
(2) Replace the following item(s):
- LCD viewer unit
- Panel cable
- Document top cover unit
- Logic board ass'y
Paper feed problems (multi- (1) Examine and remove any foreign material
feeding, skewed feeding, no from the following parts:
feeding). - ASF unit
- PE sensor
- Paper guide unit
- Pressure roller unit
- Spur unit
(2) Confirm that the paper guides are set
properly.
(3) Confirm the PF rear cover and the
cassette conditions.
(4) Confirm cable connection:
- PE sensor cable
- Paper feed relay harness ass'y
=> No incomplete connection, cable
breakage, or cable caught in units
(5) Replace the following item(s):
1/70
- ASF unit (for paper feeding error from
the rear tray)
- Pick-up arm unit (for paper feeding error
from the cassette)
- PE sensor board ass'y
- Pressure roller unit
- PE sensor cable
- Cassette unit
Faulty scanning (no scanning, (1) Confirm that the scanner lock switch is
strange noise). unlocked.
(2) Confirm cable connection:
- Scanner motor relay harness ass'y
- CCD cable
=> No incomplete connection, cable
breakage, or cable caught in units
(3) Replace the following item(s):
- Scanner unit
- Logic board ass'y

Unsatisfactory print quality No printing, or no color ejected. See 3-5. Special Notes on Servicing, (1)For
Faint printing, or white lines on smeared printing, uneven printing, or non-
printouts. ejection of ink, for details.
Uneven printing. (1) Confirm the ink tank conditions:
Improper color hue. - No remainder of the outer film (the air-
through must be opened)
- Re-setting of an ink tank
- Whether the ink tank is Canon-genuine
one or not
- Whether the ink tank is refilled one or not
(2) Remove foreign material from the purge
unit caps, if any.
(3) Perform cleaning or deep cleaning of the
print head.
(4) Perform print head alignment.
(5) Replace the following item(s):
- Print head*1, and ink tanks
- Logic board ass'y
- Purge drive system unit
Paper gets smeared. (1) Clean the inside of the machine.
(2) Perform bottom plate cleaning.
(3) Perform paper feed roller cleaning.
(4) Replace the following item(s):
- ressure roller unit (if smearing is heavy)

2/70
- Print head*1 (when smearing is caused by
the print head)
The back side of paper gets (1) Clean the inside of the machine.
smeared. (2) Perform bottom plate cleaning.
(3) Examine the platen ink absorber.
(4) Examine the paper eject roller.
(5) Replace the following item(s):
- The part in the paper path causing the
smearing
Graphic or text is enlarged on (1) Confirm that the carriage slit film is free
printouts in the carriage from smearing or scratches:
movement direction. - Cleaning of the timing slit film.
(2) Replace the following item(s):
- Timing slit strip film
- Carriage unit
- Logic board ass'y
- Scanner unit (for copying)
Graphic or text is enlarged on (1) Confirm that the LF / EJ slit film is free
printouts in the paper feed from smearing or scratches:
direction. - Cleaning of the LF / EJ slit film..
(2) Replace the following item(s):
- Timing slit disk feed film, or timing slit
disk eject film
- Timing sensor unit
- Platen unit
- Logic board ass'y
- Scanner unit (for copying)

Faulty scanning No scanning. (1) Confirm cable connection (CCD cable).


(2) Replace the following item(s):
- Scanner unit
- Logic board ass'y
Streaks or smears on the (1) Clean the platen glass and the document
scanned image. pressure sheet.
(2) Confirm the position of the document
pressure sheet.
(3) Replace the following item(s):
- Scanner unit
- Document pressure sheet
- Logic board ass'y
Smearing or streaks in film (1) Confirm that the FAU lamp turns on, and
scanning. the scanner operates properly.
3/70
No film scanning. (2) Confirm that the film is in good condition
and it is properly set in the platen glass.
(3) Replace the following item(s):
- Document pressure plate unit (FAU)
- Film guide unit
- Logic board ass'y
- Scanner unit
Network connection problem No printing. (1) Examine if printing is performed properly
via USB connection.
(2) Confirm the network connection.
(3) Replace the following item(s):
- Logic board ass'y
- Wireless LAN board ass'y
*1: Replace the print head only after the print head deep cleaning is performed 2 times, and when the
problem persists.

1-2. Operator Call Error (by Alarm LED Lit in Orange) Troubleshooting
Errors and warnings are displayed by the following ways:

1. Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are
displayed on the LCD in text and by icon.
2. Messages during printing from a computer are displayed on the printer driver Status Monitor.
3. Error codes (the latest 10 error codes at the maximum) are printed in the "operator call/service call error
record" area in EEPROM information print

Buttons valid when an operator call error occurs:

1. ON button: To turn the machine off and on again.


2. OK button: To clear and recover from an error. In some operator call errors, the error will automatically
be cleared when the cause of the error is eliminated, and pressing the OK button may not be
necessary.
3. Stop button: To cancel the job at error occurrence, and to clear the error.

Error U Parts that


code No. Message on the are likely
Error Solution
LCD to be
faulty
No paper in the [1000] --- Rear tray. Confirm that the rear tray is - PE sensor
rear tray. There is no paper. selected as the paper source. Set board
Load paper and press the paper in the rear tray, and press ass'y
[OK]. the OK button. - ASF unit
If the error is not cleared, confirm - Pressure
that no foreign material is inside roller
the paper feed slot. unit

4/70
No paper in the [1003] --- Cassette. Confirm that the cassette is - Pick-up
cassette. There is no paper. selected as the paper source. Set arm unit
Load paper and press the paper in the cassette, and press - Pressure
[OK]. the OK button. roller
Note that the cassette is for plain unit
paper only. - Cassette
unit
Paper jam. [1300] --- The paper is jammed. Remove the jammed paper and - Pick-up
Clear the paper and press the OK button. arm unit
press [OK]. For paper jam in the rear guide, - ASF unit
Paper jam in the [1303] ---
confirm that the rear guide is not - Pressure
rear guide.
dislocated. roller
unit
- Cassette
Paper jam in the [1304] --- unit
under guide. - Rear
guide
unit
Ink may have run [1600] U041 The ink may have run Replace the applicable ink tank, or - Spur unit
out. out. Replacing the ink press the OK button to clear the
tank is recommended. error without ink tank
replacement. When the error is
cleared by pressing the OK button,
ink may run out during printing.
Ink tank not [1660] U043 The following ink Install the applicable ink tank(s) - Ink tank
installed. tank cannot be properly, and confirm that the - Carriage
recognized. LED's of all the ink tanks light red. unit
(Applicable ink tank
icon)
Print head not [1401] U051 Print head is not Install the print head properly. - Print
installed, or not installed. Install the If the error is not cleared, confirm head
properly installed. print head. that the print head contact pins of - Carriage
the carriage are not bent. unit
Faulty print head U052 The type of print head Re-set the print head. If the error is - Print
ID. is incorrect. Install the not cleared, the print head may be head
correct print head. defective. Replace the print head. - Carriage
Print head [1403]
If the error is not cleared, confirm unit
temperature
that the print head contact pins of
sensor error.
the carriage are not bent.
Faulty EEPROM [1405]
data of the print
head.
5/70
Inner cover error [1841, --- Inner cover is open. Close the inner cover, and press - Spur unit
1846] close the inner cover the OK button. - Inner
and press [OK]. If the error is not cleared, examine cover
that the inner cover sensor is unit
properly installed.

Multiple ink tanks [1487] U071 More than one ink Replace the wrong ink tank(s) - Ink tank
of the same color tank of the following with the correct one(s).
installed. color is installed.
Ink tank in a [1680] U072 Some ink tanks are Install the ink tank(s) in the correct - Ink tank
wrong position. not installed in place. position.
Warning: The ink [1700] --- The ink absorber is Replace the ink absorber, and reset - Absorber
absorber becomes almost full. Press its counter. [See 3-3, Adjustment kit
almost full. [OK] to continue and Settings in Service Mode.]
printing. Contact the Pressing the OK button will exit
service center for the error, and enable printing
replacement. without replacing the ink absorber.
However, when the ink absorber
becomes full, no further printing
can be performed unless the
applicable ink absorber is
replaced.
The connected [2001] --- Incompatible device Remove the cable between the
digital camera or detected. Remove the camera and the machine.
digital video device.
camera does not
support Camera
Direct Printing.
Automatic duplex [1310] --- This paper is not The paper length is not supported - Duplex
printing cannot be compatible with two- for duplex printing. paper
performed. sided printing. Press the OK button to eject the feed
Remove the paper and paper being used at error roller
press [OK]. occurrence. unit
Data which was to be printed on - PE sensor
the back side of paper at error board
occurrence is skipped (not ass'y
printed).
Failed in [2500] --- Auto head align has Press the OK button to clear the - Carriage
6/70
automatic print failed. Press [OK] and error, then perform the automatic unit
head alignment. repeat operation. <See print head alignment again. (Use - Print
manual> Matte Photo Paper MP-101.) head
If the alignment pattern was not - Purge
printed properly (faint printing, drive
etc.), perform print head cleaning, system
then perform the print head unit
alignment again.
The remaining ink [1683] U130 (Applicable ink tank An ink tank which has once been - Ink tank
amount unknown icon) empty is installed. Replace the - Spur unit
(raw ink present). The remaining level applicable ink tank with a new
of the ink cannot be one. Printing with a once-empty
correctly detected. ink tank can damage the machine.
Replace the ink tank. To continue printing without
replacing the ink tank(s), press the
Stop button for 5 sec. or longer to
disable the function to detect the
remaining ink amount. After the
operation, it is recorded in the
machine EEPROM that the
function to detect the remaining
ink amount was disabled.
Ink tank not [1684] U140 The following ink A non-supported ink tank is - Ink tank
recognized. tank cannot be installed (the ink tank LED is
recognized. turned off). Install the supported
(Applicable ink tank ink tanks.
icon)
Ink tank not [1682] U150 The following ink A hardware error occurred in an - Ink tank
recognized. tank cannot be ink tank (the ink tank LED is
recognized. turned off). Replace the ink tank
(Applicable ink tank (s).
icon)
No ink (no raw [1688] U163 The ink has run out. Replace the empty ink tank(s), and - Ink tank
ink). Replace the ink tank. close the scanning unit (cover). - Spur unit
(Applicable ink tank Printing with an empty ink tank
icon) can damage the machine.
To continue printing without
replacing the ink tank(s), press the
Stop button for 5 sec. or longer to
disable the function to detect the
remaining ink amount. After the
operation, it is recorded in the
machine that the function to detect
the remaining ink amount was
disabled.
Non-supported [2002] --- An unsupported USB Remove the applicable USB hub
hub. hub is connected. from the PictBridge (USB)
Remove the hub. connector.

7/70
Time-out for the [2700] --- Timeout error has The buffer became full in the
scanner device. occurred. Press [OK]. middle of scanning operation, and
60 minutes have elapsed since
then, making re-scanning unstable.
Press the OK button to clear the
error.
Premium Contents [4100] --- Cannot print the data. Install the supported (Canon- - Ink tank
print error. genuine) ink tanks.

1-3. Service Call Error (by Cyclic Blinking of Alarm and Power LEDs) Troubleshooting
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the
corresponding error code with the message, "Printer error has occurred. Turn off power then back on again. If
problem persists, see the manual." is displayed on the LCD.
1) Check each point in "Check points & Solution," and perform the solution if it applies.
2) When no solution in "Check points & Solution" is effective, then replace the part listed under "Parts to be
replaced" one by one from the one most likely to be faulty. The parts are listed in the order of likeliness to be
faulty.

Cycles of Parts to be
blinking of Error replaced (when
Error Check points & Solution
Alarm and code no solution is
Power LEDs effective)
2 times Carriage error [5100] (1) Smearing or scratches on the carriage slit - Logic board
film: ass'y
Clean the film using lint-free paper. - Carriage motor
(2) Foreign material that obstructs the - Carriage unit
carriage movement: - Motor multi
Remove foreign material. harness ass'y
(3) Ink tank conditions:
Re-set the ink tanks.
(4) Cable connection:
- CR FFC (CN401, CN402, CN403)
- Motor multi harness ass'y
Re-connect the cables.
If any damage or breakage of the
cable is found, replace the cable.
(5) Scratches or damages to the carriage slit
film:
Replace the timing slit strip film.
(6) Black debris around the carriage rail or
pressure roller:
Replace the carriage unit.
3 times Line feed error [6000] (1) Opening and closing of the paper output - Timing slit disk
tray: feed film
Remove obstacles from around the - Timing slit disk

8/70
paper output tray so that the tray eject film
opens and closes properly. - Timing sensor
(2) Smearing or scratches on the LF / EJ slit unit
film: - Paper feed roller
Clean the LF / EJ slit film using lint- unit
free paper. - Logic board
(3) Foreign material in the LF drive: ass'y
Remove foreign material. - Paper feed
(4) Cable connection: motor
- LF encoder cable
- PE sensor cable
- Paper feed relay harness ass'y
- Paper feed motor harness ass'y
Re-connect the cables.
If any damage or breakage of the
cable is found, replace the cable.
(5) LF lock arm spring:
Attach the spring properly.
4 times Purge cam [5C00] (1) Foreign material around the purge drive - Purge drive
sensor error system unit: system unit
Remove foreign material. - Logic board
(2) Cable connection: ass'y
- Valve cam harness (CN700)
Re-connect the cable.
(3) Strange sound at power-on:
Replace the purge drive system unit.
5 times ASF (cam) [5700] (1) Cable connection: - ASF unit
sensor error - PE sensor cable - PE sensor board
Re-connect the cable. ass'y
If any damage or breakage of the - Logic board
cable is found, replace the cable. ass'y
6 times Internal [5400] (1) Cable connection: - Spur unit
temperature - Ink absorber multi harness (CN701) - Logic board
error Re-connect the cable. ass'y
If any damage or breakage of the - Print head
cable is found, replace the spur unit.
7 times Ink absorber [5B00] (1) Ink absorber condition:
full [5B01] Replace the ink absorber, and reset
the ink absorber counter value in the
EEPROM.
8 times Print head [5200] (1) Print head condition (face surface and - Print head
temperature rise mold): - Logic board
error If a burn mark or heat deformation is ass'y
seen on the face surface or the mold, - Carriage unit
replace the print head.
(2) Head contact pin condition of the carriage
unit:
If the pin is bent or deformed, replace
the carriage unit.
9/70
(3) Cable connection:
- CR FFC (CN401, CN402, CN403)
Re-connect the cable.
If any damage or breakage of the
cable is found, replace the carriage
unit.
9 times EEPROM error [6800] (1) Part replacement:
[6801] Replace the logic board ass'y.
10 times VH monitor [B200] (1) Print head condition (face surface and - AC adapter
error mold): - Carriage unit
If a burn mark or heat deformation is
seen on the face surface or the mold,
replace the print head and the logic
board in set. (Be sure to replace them
at the same time.)
(2) Burn mark or heat deformation of the
logic board:
If a burn mark or heat deformation is
seen on the logic board, replace the
print head and the logic board in set.
(Be sure to replace them at the same
time.)
(3) Head contact pin condition of the carriage
unit:
If the pin is bent or deformed, replace
the carriage unit.
(4) Cable connection:
- CR FFC (CN401, CN402, CN403)
Re-connect the cable.
If any damage or breakage of the
cable is found, replace the carriage
unit.
11 times Carriage lift [5110] (1) Foreign material that obstructs the - Switch system
mechanism carriage movement: unit
error Remove foreign material. - Carriage unit
12 times APP position [6A80] (1) Cap absorber and wiper blade: - Timing slit disk
error If the cap absorber contacts the wiper APP film
blade, lower the cap absorber so that - PE sensor board
it will not contact the wiper blade. ass'y
(2) Foreign material around the purge drive - Purge drive
system unit: system unit
Remove foreign material. - Logic board
APP position [6A81] (3) Ink absorber right beneath the purge drive ass'y
error during system unit:
initial purging Confirm that the absorber stays in
place and does not contact the unit.
(4) Foreign material around the ASF unit:
Remove foreign material.
(5) APP slit film condition:

10/70
14 times APP sensor [6A90] Clean the APP slit film using lint-free
error paper.
(6) APP code wheel gear condition:
If the gear wears, replace the gear.
(7) Cable connection:
- PE sensor cable
- Motor multi harness ass'y
Re-connect the cables.
If any damage or breakage of the
cable is found, replace the cable.
Paper feed cam [6B10] (1) Ink absorber counter value: - Pick-up arm
sensor error If the value exceeds 60%, replace the unit
ink absorber. Follow the "Guideline - Duplex paper
for Preventive Replacement of the Ink feed roller unit
Absorber."
(2) Jammed paper or foreign material in the
under guide:
Remove the jammed paper and
foreign material.
15 times USB host Vbus [9000] (1) Part replacement:
overcurrent Replace the logic board ass'y.
16 times Pump roller [5C20] (1) Cable connection: - Purge drive
sensor error - Valve cam harness (CN700) system unit
Re-connect the cable.
17 times Paper eject [6010] (1) Smearing on the LF / EJ slit film: - Timing sensor
encoder error Clean the LF / EJ slit film using lint- unit
free paper. - Platen unit
(2) Foreign material in the paper path: - Logic board
Remove foreign material. ass'y
(3) Cable connection: - Paper feed
- LF encoder cable motor
- PE sensor cable
Re-connect the cable.
If any damage or breakage of the
cable is found, replace the cable.
(4) Scratches on the LF / EJ slit film:
Replace the timing slit disk feed film
or the timing slit disk eject film.
19 times Ink tank [6502] (1) Ink tank position: - Spur unit
position sensor Confirm the ink tank position. - Logic board
error (2) Re-set or replacement of ink tanks: ass'y
If the error persists, replace the ink
tanks.
(3) Cable connection:
- Ink absorber multi harness (CN701)
Re-connect the cable.
20 times Other errors [6500] (1) Cable connection: - Logic board
- Wireless LAN cable ass'y

11/70
Re-connect the cable. - Wireless LAN
If any damage or breakage of the board ass'y
cable is found, replace the cable.
21 times Drive switch [C000] (1) Foreign material in the drive switch area - Purge drive
error of the purge drive system unit: system unit
Remove foreign material. - ASF unit
(2) Ink tank conditions: - Carriage unit
Confirm that the ink tanks are seated
properly and they do not interfere
with the carriage movement.
22 times Scanner home [5000] (1) Cable connection: - Scanner unit
position sensor - CCD FFC (CN1100) - Logic board
error - Scanner motor relay harness ass'y ass'y
Re-connect the cables.
Scanner error [5011] (1) Cable connection: - Scanner unit
- CCD FFC (CN1100) - Logic board
- Lamp harness ass'y ass'y
- Scanner motor relay harness ass'y - Scanner motor
Re-connect the cables. relay harness
(2) Document pressure sheet conditions: - Lamp harness
Re-attach the document pressure ass'y
sheet, or replace it.
Error during [5021] (1) Scanner lock switch: - Scanner unit
scanning Unlock the switch, - Logic board
operation and power off and on the machine ass'y
again.
(2) Cable connection:
- CCD FFC (CN1100)
- Lamp harness ass'y
- Scanner motor relay harness ass'y
Re-connect the cables.
Scanner light [5030] (1) Cable connection: - Scanner unit
source not - CCD FFC (CN1100) - Logic board
turned on - Lamp harness ass'y ass'y
Re-connect the cables.
(2) Document pressure sheet conditions:
Re-attach the document pressure
sheet, or replace it.
Scanner electric [5050] (1) Cable connection: - Scanner unit
circuit error - CCD FFC (CN1100)
- Lamp harness ass'y
- Scanner motor relay harness ass'y
Re-connect the cables.
23 times Valve cam [6C10] (1) Foreign material around the purge drive - Purge drive
sensor error system unit: system unit
Remove foreign material. - Logic board
(2) Cable connection: ass'y
- Valve cam harness (CN700)
12/70
Re-connect the cable.
Alarm and Scanner lock [5020] (1) Scanner lock switch: - Scanner unit
Power LED's error Unlock the switch,
lit and power off and on the machine
again.
(2) Cable connection:
- CCD FFC (CN1100)
Re-connect the cables.

Before replacement of the logic board, check the ink absorber counter value, and register it to
the replaced new logic board. (The value can be set in 10% increments.) In addition, according
to the "Guideline for Preventive Replacement of Ink Absorber," replace the ink absorber. [See
3. ADJUSTMENT / SETTINGS, 3-3. Adjustment and Settings in Service Mode, for details.]

<1. TROUBLESHOOTING>

13/70
MG8100 series TABLE OF CONTENTS

2. REPAIR

2-1. Major Replacement Parts and Adjustment

Service part Recommended removal procedure*1 / Notes on Adjustment / settings / operation


replacement check
Logic board (1) Cassette unit In the service mode:
ass'y (2) Left and right side covers 1. Set the ink absorber counter
(3) Document pressure plate unit (FAU) value.
(4) Scanner unit 2. Set the destination.
(5) Main case 3. Print the integrated inspection
(6) Rear cover pattern.
(7) Logic board ass'y 4. Perform LF / Eject correction
(only when streaks or uneven
- Before replacement, check the ink absorber counter printing occurs).
value (by service test print or EEPROM 5. Set the sensitivity of the
information print). capacitive sensors.
- Before removal of the logic board ass'y, remove the [See 3-3. Adjustment and
power cord, and allow for approx. 1 minute (for Settings in Service Mode, (7)
discharge of capacitor's accumulated charges), to Capacitive sensor sensitivity
prevent damages to the logic board ass'y. setting, for details.]
6. Print the EEPROM information.
[See 3-3. Adjustment and
Settings in Service Mode, for
details.]
In the user mode:
7. Set the language displayed on the
LCD.
8. Reset the LAN settings.
9. Perform print head alignment.
10. Print via USB connection.
11. Copy.
12. Perform direct printing from a
digital camera (PictBridge).
Absorber kit (1) Cassette unit In the service mode:
(2) Left and right side covers 1. Reset the ink absorber counter.
(3) Document pressure plate unit (FAU) [See 3-3. Adjustment and
(4) Scanner unit Settings in Service Mode, for
(5) Main case details.]
(6) Rear cover After the ink absorber counter is
(7) Print unit reset, the counter value is printed
(8) Ink absorber automatically.

- See 2-2. Part Replacement Procedures, (11) Ink


absorber replacement, for details.
Carriage unit (1) Cassette unit 1. Apply grease to the sliding
(2) Left and right side covers portions of the carriage rail.
(3) Document pressure plate unit (FAU) [See 3-4. Grease Application, for

14/70
(4) Scanner unit details.]
(5) Main case
(6) Rear cover In the service mode:
(7) Timing slit strap 2. Print the integrated inspection
- Before removal of the carriage rail, put a mark of the pattern.
carriage rail position. [See 3-3. Adjustment and
(8) Carriage upper rail Settings in Service Mode, for
(9) Carriage unit details.]

In the user mode:


- Keep the timing slit strap (carriage encoder film) 3. Perform automatic print head
free from stain or damage. When returning the alignment.
strap, make sure of its orientation (left and right,
front and back).
- See 2-2. Part Replacement Procedures, (7) Carriage
unit removal, for details.
Switch system (1) Cassette unit 1. Adjust the paper feed motor.
unit (2) Left and right side covers [See 3-5. Special Notes on
(3) Document pressure plate unit (FAU) Servicing, (2) Paper feed motor
(4) Scanner unit adjustment, for details.]
(5) Main case
(6) Rear cover In the service mode:
(7) Print unit 2. Print the integrated inspection
(8) See 2-2. Part Replacement Procedures. pattern.

Paper feed - The screws securing the paper feed motor are
motor allowed to be loosened only for paper feed motor
replacement. (DO NOT loosen them in any other
cases.)
- See 2-2. Part Replacement Procedures, (9) Purge
drive system unit (right plate) and switch system
unit (left plate) removal, for details.
- See 2-2. Part Replacement Procedures, (10) Engine
unit reassembly, for details.
Platen unit (1) Cassette unit In the service mode:
(2) Left and right side covers 1. Perform LF / Eject correction
(3) Document pressure plate unit (FAU) (only when uneven printing or
(4) Scanner unit streaks appear on printouts after
(5) Main case replacement).
(6) Rear cover [See 3-3. Adjustment and
(7) Print unit Settings in Service Mode, for
(8) See 2-2. Part Replacement Procedures, from this details.]
step. 2. Print the integrated inspection
pattern.
Spur unit (1) Cassette unit In the service mode:
(2) Left and right side covers 1. Print the integrated inspection
(3) Document pressure plate unit (FAU) pattern.
(4) Scanner unit 2. Perform LF / Eject correction
(5) Main case (only when uneven printing or
(6) Rear cover streaks appear on printouts after
15/70
(7) Print unit replacement).
(8) See 2-2. Part Replacement Procedures. [See 3-3. Adjustment and
Settings in Service Mode, for
- DO NOT contact the spur edges. details.]
Purge drive (1) Cassette unit In the service mode:
system unit (2) Left and right side covers 1. Print the integrated inspection
(3) Document pressure plate unit (FAU) pattern.
(4) Scanner unit
(5) Main case
(6) Rear cover
(7) Print unit
(8) See 2-2. Part Replacement Procedures.

- See 2-2. Part Replacement Procedures, (9) Purge


drive system unit (right plate) and switch system
unit (left plate) removal, for details.
- See 2-2. Part Replacement Procedures, (10) Engine
unit reassembly, for details.
Carriage rail See 2-2. Part Replacement Procedures, and Parts 1. Apply grease to the sliding
and main Catalog. portions.
chassis [See 3-4. Grease Application, for
details.]
Idler pulley
parallel pin
In the service mode:
APP code 2. Print the integrated inspection
wheel gear pattern.
shaft
Document (1) Cassette unit 1. Confirm the document pressure
pressure sheet (2) Left and right side covers plate sheet position.
(3) Document pressure plate unit (FAU) [See 3-5. Special Notes on
(4) Scanner unit Servicing, (4) Document pressure
sheet replacement, for details.]

Scanner unit In the service mode:


2. Print the integrated inspection
pattern.
Document (1) Right side cover In the service mode:
pressure plate (2) Document pressure plate unit (FAU) 1. Perform button and LCD test.
unit (3) Document top cover unit [See 3-3. Adjustment and
(4) LCD viewer Settings in Service Mode, for
details.]
- Be cautious not to scratch or damage the LCD 2. Set the sensitivity of the
Document top
cable. capacitive sensors.
cover unit
- To protect the external housing of the machine [See 3-3. Adjustment and
from scratches, spread a soft cloth and Settings in Service Mode, (7)
disassemble / reassemble the machine on it. Capacitive sensor sensitivity
LCD viewer
setting, for details.]
unit
3. Print the integrated inspection
pattern.

16/70
Timing slit See 2-2. Part Replacement Procedures, and Parts In the user mode:
strip film Catalog. 1. Perform print head alignment.

Timing slit In the service mode:


disk feed film 2. Print the nozzle check pattern.
- Upon contact with the film, wipe the film with 3. Perform LF / Eject correction
ethanol. (only when uneven printing or
- Confirm no grease is on the film. (Wipe off any streaks appear on printouts after
Timing slit
grease thoroughly with ethanol.) replacement).
disk eject film
- Do not bend the film. [See 3-3. Adjustment and
Settings in Service Mode, for
details.]
Print head In the user mode:
1. Perform print head alignment.

In the service mode:


2. Print the integrated inspection
pattern.
Wireless LAN (1) Cassette unit In the user mode:
board ass'y (2) Left and right side covers 1. Reset the LAN settings.
(3) Document pressure plate unit (FAU)
(4) Scanner unit In the service mode:
(5) Main case 2. Print the integrated inspection
(6) WLAN board pattern, and confirm that the
WLAN MAC address is properly
updated.
Bottom case (1) Cassette unit In the service mode:
(2) Left and right side covers 1. Print the integrated inspection
(3) Document pressure plate unit (FAU) pattern.
(4) Scanner unit
(5) Main case
(6) Front door / bottom case
*1: To reassemble the unit after replacement, follow the procedures in the reverse order.

General notes:
- Make sure that the flexible cables and wires in the harness are in the proper position and connected
correctly. See 2-2. Part Replacement Procedures or the Parts Catalog for details.
- Do not drop the ferrite core, which may cause damage.
- Protect electrical parts from damage due to static electricity.
- Before removing a unit, after removing the power cord, allow the machine to sit for approx. 1 minute
(for capacitor discharging to protect the logic board ass'y from damages).
- Do not touch the timing slit strip film, timing slit disk feed film, and timing slit disk eject film. No
grease or abrasion is allowed.
- Protect the units from soiled with ink.
- Protect the housing from scratches.
- For automatic print head alignment, use Matte Photo Paper MP-101 to maintain the alignment
accuracy.
17/70
- Exercise caution with the screws, as follows:
i. The screws of the paper feed motor may be loosened only at replacement of the paper feed
motor unit (DO NOT loosen them in other cases).
ii. Before loosening the 3 screws that fix the carriage rail to the main chassis, mark the screw
positions so that the carriage rail will be re-attached to the main chassis in its original
position. [See 2-2. Part Replacement Procedures, (7) Carriage unit removal, for details.]

<2-1. Major Replacement Parts and Adjustment>

18/70
MG8100 series --- 2. REPAIR TABLE OF CONTENTS

2-2. Part Replacement Procedures


Be sure to protect the machine from static electricity in repair servicing, especially for the LCD, document top
cover, scanner unit, logic board, card board, IrDA board, PE sensor board, and WLAN board.
Some of the photos are of the iP4700, iP4800, MP640, MP990, and MG6100 series since their structures are same.

(1) External housing, scanner unit, and document cover removal


1) Remove the cassette.
2) Open the front door and scanner unit, then remove the side cover R (2 screws).

3) Remove the scanner FFC, panel cable, FAU lamp cable, and FB motor cable.
<Be cautious of the core location and wiring layout.>

Disconnect the red-circled cables.


19/70
4) Remove the side cover L, scanner unit, then document pressure plate unit (2 screws).
<While holding the scanner unit, sliding it to the right and disengage it from the scanner support
arm.>

Remove 2 screws at the center of the side cover L.

[1] Lift the back of the scanner unit.


[2] Slide it to the right to disengage from the support
arm.

20/70
5) Remove the main case (no screws).

21/70
(2) Operation panel removal
1) Separate the document pressure plate from the scanner unit.
<While pushing the hinge edge inward, pull the plate upward to separate it from the scanner
unit.>
<Remove the panel cable through the slit of the scanner unit. It will make it easier if the cable
core is removed first.>

2) Remove the top cover from the base (13 screws).


To protect the unit from scratches, spread a soft cloth and handle the unit on it.
<Remove the FAU protection sheet and the screws. Then, release the claws near the hinges to
separate the top cover from the base.>

13 screws Be cautious not to damage the claws.

22/70
3) Remove the LCD unit (4 screws).
<Cut the fabric sheet along the perforation. In reassembling, attach the new fabric sheet as it
is over the remaining portions of the sheet.>

the fabric sheet along the perforation and disconnect rews


the flexible cable.

h the LCD unit to separate it from the panel.

(3) Cable wiring and connection


1) Wiring on the right side (on the logic board side)

23/70
2) Wiring of the ink sensor cable, inner cover open sensor cable, WLAN FFC, and PictBridge FFC
<When connecting the WLAN or PictBridge FFC, first fold it according to the instructions
below, then connect it.>

PBIR FFC WLAN FFC

PBIR_FFC & W-LAN_FFC PDF (A4)

24/70
3) Wiring on the left side. Pass the ground cable through the hole to hook it on the side of the bottom
case.

(4) Document window R removal


The window is fixed with the double-sided adhesive tape. Insert a precision screwdriver, etc. into the gap and
slowly remove the window from the tape.

(5) Carriage unlocking


1) Rotate the APP motor drive gear in the red arrow direction in the left photo below to unlock the
carriage.
Slide the carriage to the left (the opposite of the home position).

25/70
(6) ASF unit removal
1) Remove the PE sensor board first, then remove 1 screw from the left plate (the left side of the
ASF unit), and 2 screws from the right plate (the right side of the ASF unit).

(7) Carriage unit removal


1) Unlock the carriage while following the procedures (5) Carriage unlocking.
2) On the main chassis, mark the positions of the screws that fix the carriage upper rail to the main
chassis (3 points for each screw: the left, right, and center).

3) Remove 3 screws that fix the carriage upper rail to the main chassis, then remove the rail.

26/70
4) Slowly slide the carriage unit to where the main chassis is cut as shown in the photo below.

5) Remove the timing slit film. Be cautious to keep it free from any grease or damage.

6) Pass the head of a flat-blade screwdriver through the hole of the main chassis, and press the
carriage belt to release it from the pulley. Be cautious to keep it free from any grease.

27/70
7) Disconnect the carriage FFC from the logic board connector, then remove the carriage cable
cover, carriage cable holder, and FFC core.

8) While being cautious so that the carriage unit will not contact the main chassis, slowly lift the
carriage unit to remove it from the main unit.

28/70
In assembling a new carriage unit, follow the procedures in the reverse order. For the carriage upper
rail, align the rail to the marks that were put in the first step of disassembly, and securely fasten the
screws.

If the carriage unit is not necessary to be replaced, parts under the purge drive system unit, etc.
can be replaced without removing the carriage rail. While holding a set of a) main chassis, b)
upper and lower carriage rails, and c) carriage unit together, just remove the screws from the
left and right plates. This way, you just have to reassemble the set of units (marking of the
carriage rail position to the main chassis is not necessary).

(8) Spur unit and platen unit removal


1) Remove the ink sensor and the inner cover sensor from the front chassis (1 screw each).

2) From the left and right sides of the spur unit, release the springs (2 on the left side, 1 on the right
side). Then, slowly pull the spur unit upward to remove it from the platen unit.

29/70
3) Remove the front chassis (3 screws).

4) Unlock the paper eject roller gear. While raising the front of the platen unit, remove the platen
unit from the printer unit.

30/70
(9) Purge drive system unit (right plate) and switch system unit (left plate) removal
1) Release the springs of the carriage motor cable, duplex printing paper feed roller, cassette feed
roller, cassette feed guide, and paper guide unit (both sides). (See the Parts Catalog for details.)

2) Remove the springs (left and right) from the pressure roller unit.
3) Remove the screws that fix the units to the main chassis (2 on the right, 3 on the left).

31/70
4) Separate the main chassis from the switch system unit and the purge drive system unit.

(10) Engine unit reassembly


After repair, reassemble each unit of the printer engine on the bottom case in the procedures listed below.
Depending on the replaced unit, some steps can be omitted. For specific part names and locations, refer to the
Parts Catalog.

1) Install the switch system unit in the bottom case while fitting the joint to the FD link unit, then
fasten the screws (3 screws).
Although the AC adapter is already attached in the photo below, it can be attached in the last step
of reassembly if it is easier for you to reassemble the units.

32/70
2) Attach the duplex print paper feed roller unit to the purge drive system unit, and fix them to the
bottom case with the screws (3 screws).

3) Attach the cassette feed guide.

33/70
4) Install the cassette feed roller unit.

5) To the paper feed roller unit, attach the paper feed belt and bushing, then install them in the main
unit.

6) Attach the paper guide unit from above the paper feed roller along its bushing, then hook the end
34/70
of each spring on the protrusion of the right and left plates respectively.

7) Install the platen unit and the spur unit.

8) Connect the springs on each side of the spur holder to the switch system unit and the purge drive
system unit respectively.

35/70
9) Attach the inner cover and the release arms (2 arms).

10) Fix the pressure roller unit to the main chassis (screw it to the right and left plates).

11) Attach the carriage unit to the carriage rail, then align the carriage upper rail with the marks on
the main chassis and fasten it with screws.
36/70
The carriage unit will be easy to be attached to the carriage rail when the lever is slid in the red-
arrowed direction in the photo below.

12) Hook the torsion springs of the pressure roller unit to the main chassis, then the springs kept at
the right and left plates in step 6) to the main chassis.
37/70
<Springs in step 6)>

<Springs hooked>

13) While being cautious not to damage the carriage FFC, install the front chassis, hook the springs,
and connect the ground harness.

38/70
14) Attach the ink sensor to the front chassis.

15) Install the ASF unit and attach the PE sensor board.

39/70
16) Install the main PCB chassis.

40/70
17) Arrange each harness.

18) Attach the carriage encoder film.


First, pass the encoder film through the slit of the carriage unit, and hook the hole on the right of
the film to the main chassis. Then, attach the spring in the left hole of the encoder film, and hook
the other end of the spring to the main chassis.

41/70
(11) Ink absorber replacement
If the ink absorber alone needs to be replaced (because the ink absorber becomes full, etc.) and no other engine
parts are replaced, the ink absorber can be replaced only by separating the print unit from the bottom case. It is not
necessary to disassemble the whole engine unit.

1) Disconnect the DC harness from the logic board (right side of the machine).
2) Disconnect the ground cable from the front chassis (left side of the machine).
3) Remove a total of 7 screws that fix the switch system unit to the bottom case, and the purge drive
system unit to the bottom case.

Specific screw location:

42/70
4) Slowly lift the print unit to separate it from the bottom case.

43/70
5) Remove the paper separation slope, since a portion of the ink absorber lies under it.

6) Replace the ink absorber.


Confirm that the replaced new ink absorber completely fits in place and is not lifted or dislocated,
especially under the pump.

7) While being cautious of the ink tube and each harness location, return the print unit to the bottom
case, and fasten the screws (7 screws removed in step 3).
8) Properly arrange and connect the harnesses, install the scanner unit, and attach the document
pressure plate unit and external housing.

After replacement of the ink absorber, reset the ink absorber counter (or set the appropriate
counter value) in the service mode.
For details, see 3-3. Adjustment and Settings in Service Mode.

<2-2. Part Replacement Procedures>


44/70
MG8100 series TABLE OF CONTENTS

3. ADJUSTMENT / SETTINGS

3-1. Adjustment
Approx.
Adjustment Purpose Method
time
EEPROM To initialize settings. Service Tool*2, 1 min.
initialization EEPROM Clear
Destination settings To set the machine destination. Service Tool*2, 1 min.
(EEPROM settings) - At logic board replacement "Set Destination" section
Ink absorber counter To reset the ink absorber counter. Service Tool*2, 1 min.
resetting - At ink absorber replacement Main in the "Clear Ink
(EEPROM settings) Counter" section
Ink absorber counter To set the data of the actual ink Service Tool*2, 1 min.
value setting amount absorbed in the ink absorber "Ink Absorber Counter"
(EEPROM settings) to the EEPROM. section
- At logic board replacement
Paper feed motor To adjust the belt tension. Fix the paper feed motor so 5 min.
position adjustment (Position the paper feed motor so that that the belt is stretched
the belt is stretched tight.) tight. (See 3-5. Special
- At paper feed motor replacement Notes on Servicing, (2)
Paper feed motor
adjustment, for details.)
Automatic print head To secure the dot placement Perform automatic print 6 min.
alignment accuracy. head alignment in the user
- At print head replacement mode.
- At logic board replacement Recommended for the
- When print quality is not satisfying MG8100 series.
Manual print head To secure the dot placement Perform manual print head 10 min.
alignment accuracy. alignment in the user mode.
- At print head replacement
- At logic board replacement
- When print quality is not satisfying
even after automatic print head
alignment is performed
Grease application To maintain sliding properties of the Using a brush, etc., apply 1 min.
applicable portions. FLOIL KG-107A.
- At carriage unit replacement
- At APP motor replacement
Ink system function To maintain detection functionality Service Tool*2, 1 min.
check for presence of the ink tanks and each Test Print in the "Print"
ink tank position. section
- At logic board replacement
- At spur unit replacement
- At carriage unit replacement

45/70
LCD language To set the language to be displayed Set the language in the user 1 min.
settings on the LCD. mode.
Not necessary when the machine is
set to the default at shipment from
the production site (On arrival at
user's, the user is to set the language
during setup.).
- At logic board replacement
Platen glass To maintain scanning accuracy, hold In the user mode: 2 min.
protection sheet the sheet with the long side down, (1) Without any document
(document pressure then fit its upper left corner to the on the platen glass,
sheet) position platen glass reference mark (back perform copying.
adjustment left). (2) Confirm that no black
- At protection sheet replacement streaks are on the
- At FAU protection sheet printout.
replacement
- At document pressure plate unit
replacement
- At scanner unit replacement
LF / Eject correction To correct line feeding. Service Tool*2, 5 min.
(manual) - At paper feed roller replacement (1) In the "Print" section,
- At platen unit replacement click LF/EJECT.
- At logic board replacement (2) According to the printed
- At LF / EJ slit film replacement pattern, set the
- At timing slit film replacement correction value in the
"LF / EJECT
Correction" section.
N LF / Eject correction Service Tool*2, in the "Auto 3 min.
(automatic) LF/EJ" section,
Recommended for the (1) Click Print.
MG8100 series (2) Place the printed pattern
on the platen glass, and
click Scan. The
correction value is
automatically set.
Recommended for the
MG8100 series.
Carriage rail position To set the carriage rail to the original Put a mark using a sharp- 1 min.
adjustment position prior to removal or pointed metallic stick, such
replacement of the carriage unit, put as a wimble.
a mark on the main chassis before
removal of the carriage unit.

N Capacitive sensor To correct variation in sensitivity of Service Tool*2, 5 min.

46/70
sensitivity setting the capacitive sensors. "Panel Rank" section
- At logic board replacement
- At document pressure plate unit
replacement
- At document top cover unit
replacement
- When user complaints about the
sensitivity of the operation panel
arise
N: New adjustment item
*2: Install the Service Tool to a pre-registered computer.

- The screws securing the paper feed motor may be loosened only at replacement of the paper
feed motor unit.
- For the automatic print head alignment, use Matte Photo Paper (MP-101), which is packed
with the machine before shipment. If Matte Photo Paper (MP-101) is not available, perform
manual print head alignment using plain paper.
- For the automatic LF / Eject correction, be sure to use Matte Photo Paper (MP-101).

3-2. Adjustment and Maintenance in User Mode


Function Procedures Remarks
Nozzle Perform via the machine operation Set a sheet of plain paper (A4 or Letter) in the
check panel, or from the printer driver cassette, or the rear tray if selected.
pattern Maintenance tab.
printing
Print head - Cleaning both Black and Color: Unclogging of the print head nozzles, and
manual Perform via the machine operation maintenance to keep the print head conditions good.
cleaning panel. If there is a missing portion or white streaks in the
- Cleaning Black or Color separately, or nozzle check pattern printout, perform this cleaning.
both Black and Color:
Perform from the printer driver
Maintenance tab.
Print head Perform via the machine operation If print head manual cleaning is not effective, perform
deep panel, or from the printer driver this cleaning. Since the deep cleaning consumes more
cleaning Maintenance tab. ink than regular cleaning, it is recommended to
perform deep cleaning only when necessary.
Automatic Perform via the machine operation Set a sheet of Matte Photo Paper MP-101 (A4) in the
print head panel, or from the printer driver rear tray. If the automatic print head alignment is not
alignment Maintenance tab. effective, perform manual print head alignment.
Manual print Perform via the machine operation Set 3 sheets of plain paper (A4 or Letter) in the
head panel, or from the printer driver cassette, or the rear tray if selected.
alignment Maintenance tab.
Print head Perform via the machine operation Confirmation of the current print head alignment
alignment panel, or from the printer driver values.
value Maintenance tab.
47/70
printing
Paper feed Perform via the machine operation The paper feed rollers of the selected paper source
roller panel, or from the printer driver (the rear tray or the cassette) rotate while being
cleaning Maintenance tab. pushed to the paper lifting plate. Since the rollers will
wear out in this cleaning, it is recommended that you
perform this only when necessary.
Bottom plate Perform via the machine operation Cleaning of the platen ribs when the back side of
cleaning panel, or from the printer driver paper gets smeared.
Maintenance tab. Fold a sheet of plain paper (A4 or Letter) in half
crosswise, then unfold and set it in the rear tray with
the folded ridge facing down. (No paper feeding from
the cassette)
LAN Perform via the machine operation Resetting of the LAN settings to default via the
resetting panel, or using IJ Network Tool. operation panel (Setup -> Device settings -> LAN
settings -> Reset LAN settings), or using IJ Network
Tool.

3-3. Adjustment and Settings in Service Mode


(1) Service mode operation procedures
Use the Service Tool on the connected computer.
1) Start the machine in the service mode.
i. With the machine power turned off, press and hold the ON button. (DO NOT release the button.)
ii. When the Power LED lights, while holding the ON button, press the Stop button 5 times*1, and release the
ON button. (Each time the Stop button is pressed, the Alarm and Power LEDs light alternately.)
iii. When the Power LED lights, the machine is ready for the service mode operation.
*1: Without the scanner, press the Stop button 6 times.

2) Start the Service Tool on the connected computer.


i. When a button is clicked in the Service Tool dialog box, that function is performed. During operation of the
selected function, all the Service Tool buttons are dimmed and inactive.
ii. When the operation is completed, "A function was finished." is displayed, and another function can be
selected.
iii. If a non-supported function is selected, "Error!" is displayed. Click OK in the error message dialog box to
exit the error.

(2) Service Tool functions


Service Tool screen: Version 1.081

48/70
No. Name Function Remarks
1 Test Print Service test print Paper will feed from the rear tray (2 sheets).

Service test print:


- Model name
- ROM version
- USB serial number
- Process inspection information
- Barcode (model name + destination + machine serial
number)
- Ink system function check result (printed on the second
sheet)

49/70
2 EEPROM EEPROM information The dialog box opens to select the paper source. Select
print Rear tray or Cassette, and click OK.

EEPROM information print:


- Model name
- ROM version
- Ink absorber counter value (ink amount in the ink
absorber)
- Print information
- Error information, etc.
3 Nozzle Check Nozzle check pattern print The dialog box opens to select the paper source. Select
Rear tray or Cassette, and click OK.
The same pattern as the one in the user mode is printed.
4 Integration Integrated inspection Paper will feed from the rear tray (if the cassette is
pattern print (Nos. 1 to 3 selected, the error is displayed).
are successively printed.) Multiple inspection items are printed just in one page, it is
recommended to use this function for the standard
inspection.

Printed items:
- Model name
- ROM version
- USB serial number
- Nozzle check pattern (same as the one in the user mode)
- Process inspection information
- Barcode (machine serial number)
- Ink system function check result

5 EEPROM EEPROM information The EEPROM information is displayed on the computer


saving or is saved to the computer as a text file. This function is
not available in most cases of errors.
6 N/A

7 LF / EJECT LF / Eject correction Perform LF / Eject correction only when streaks or uneven
pattern print printing occurs after the repair. See "(3) LF / Eject
correction (automatic / manual)" below.
8 Left Margin Left margin pattern print Not used.
9 Auto Cleaning Enabling / disabling of Automatic print head cleaning prior to printing (after
automatic print head replacement of an ink tank or the print head). Select this
cleaning option to enable the cleaning.
10 Deep Cleaning Print head deep cleaning Cleaning of both Black and Color at the same time
11 Main Main ink absorber counter Set a sheet of A4 or Letter sized plain paper. After the ink
(Clear Ink resetting absorber counter is reset, the counter value is printed
Counter) automatically.
Platen Platen ink absorber counter Not used.
(Clear Ink resetting
50/70
Counter)
12 EEPROM Clear EEPROM initialization The following items are NOT initialized, and the shipment
arrival flag is not on:
- USB serial number
- Destination settings
- Record of ink absorber counter resetting and setting
- Disc label print position correction value
- LF / Eject correction values
- Left margin correction value
- Production site E-MIP correction value and enabling of it
- Endurance correction value and enabling of it
- Record of disabling the function to detect the remaining
ink amount
- Ink absorber counter value (ink amount in the ink
absorber)
13 Panel Check Button and LCD test See "(4) Button and LCD test" below.
14 Clear S/N Serial number resetting (to The machine serial number is reset to "000000000."
zero) Not used in regular repair.
15 Set Destination Destination settings Select the destination, and click Set.
ASA, AUS, BRA, CHN, CND, EMB, EUR, JPN, KOR,
LTN, TWN, USA
16 N/A

17 LF / EJECT LF / Eject correction value See "(3) LF / Eject correction (automatic / manual)"
Correction setting below.
Set the correction value based on the printed pattern (7.
LF / EJECT correction pattern print).
18 Auto LF / EJ Automatic LF / Eject More accurate correction than the manual one.
correction Recommended for the MG8100 series. (Use Matte Photo
Paper MP-101.)
19 Left Margin Left margin correction Not used.
Correction value setting
20 Ink Absorber Ink absorber counter See "(5) Ink absorber counter setting" below.
Counter setting
21 Wetting Liquid Wetting liquid counter Not used.
Counter setting
22 Panel Rank Capacitive sensor Adjustment of the sensitivity of the capacitive sensors.
sensitivity setting See "(7) Capacitive sensor sensitivity setting" below.
23 Flatbed Scanner Individual scanner Not used.
adjustment

(3) LF / Eject correction (automatic / manual)

51/70
After replacement of the feed roller, platen unit, LF / Eject slit film, timing slit film, or logic board in repair
servicing or in refurbishment operation, perform the adjustment to maintain the optimal print image quality.
If the print quality is considered unaffected by replacement of those parts, it is not necessary to perform LF / Eject
correction.

< Automatic correction >


In the automatic correction, line feeding can be adjusted more accurately than in the manual correction. For the
MG8100 series, automatic LF / Eject correction is recommended.
1) Print the LF / Eject correction pattern.
In the Auto LF/EJ section of the Service Tool, click Print, select the paper type, and print the pattern.
- Media size: Select either A4 or LTR.
- Media type: Select MP-101.
2) When printing is finished, the machine returns to be ready for selection of another function ("A function was
finished" is displayed on the screen).

52/70
3) Scan the printed pattern.
Place the printed pattern on the platen glass with the printed side facing down and with the blue triangle in the
upper left corner aligning to the platen glass reference mark, then click Scan of the Service Tool.
The LF / Eject correction values will be written to the EEPROM automatically, then "A function was finished"
is displayed on the screen to indicate that the machine returns to be ready for selection of another function.
4) When the LF / Eject correction values are written to the EEPROM, the E-MIP correction value that was set at
shipment from the production site becomes invalid.

< Manual correction >


1) Print the LF / Eject correction pattern.
Click LF/EJECT of the Service Tool, select the paper source and the paper type, and print the pattern. 5 sheets
of A4 paper will be used for the pattern printing.
- Paper source: Select either Rear tray or Cassette.
- Media type: Select one from HR-101, GF-500/Office Planner, HP Bright White, and Canon
Extra/STEINBEIS.
2) When printing is finished, the machine returns to be ready for selection of another function ("A function was
finished" is displayed on the screen).
3) In the printout, determine the Pattern No. in which streaks or lines are the least noticeable for the LF check
pattern and the Eject check pattern respectively.
(LF Pattern No. 0 to 4, Eject Pattern No. 0 to 4)

4) Select and set the correction values.


In the LF/EJECT Correction section of the Service Tool, select the Pattern No. (from 0 to 4) determined in
step 3) for LF and EJECT respectively, and click Set.
5) The selected LF and Eject correction values are written to the EEPROM, making the E-MIP correction value
(which was set at shipment from the production site) invalid.
Note: At the production site, the E-MIP correction, which is equivalent to the LF / Eject
correction, is performed using the special tool, and the E-MIP correction value is written to
the EEPROM as the valid data.
53/70
When LF / Eject correction is performed, the LF / Eject correction values become valid instead of
the E-MIP correction value (thus, in the initial EEPROM information print, "LF = *" and
"EJ = *" are printed, but the selected values are printed after the LF / Eject correction).

(4) Button and LCD test


Confirm the operation after replacement of the operation panel unit, panel board, or LCD.
1) Check to see if the LED turns off properly
1-1) Click Panel Check of the Service Tool. All the LED's on the machine turn on and the LCD turns blue,
waiting for a button to be pressed.
1-2) Press the OK button multiple number of times, and confirm that the LED turns off in the following order
from No. 1 to No. 20 each time the OK button is pressed:
No. No.
1. left function button 11. up cursor
2. center function button 12. right cursor
3. right function button 13. down cursor
4. "Start" text 14. left cursor
5. "Stop" text 15. Back button
6. Stop button 16. HOME button
7. Color button 17. Power lamp
8. Black button 18. Alarm lamp
9. + - buttons 19. Wi-Fi lamp
10. Scroll Wheel 20. OK button
1-3) Press the OK button. The machine becomes ready for the next operation.
2) Button check
2-1) Press each button of the operation panel, to see if every button functions properly.
2-2) The LCD is divided into 24 segments, representing each button. The color of a segment corresponding to
the pressed button changes to red. If 2 or more buttons are pressed at the same time, only one of them is
considered to be pressed, and the other buttons are ignored.

1. ON button 9. Color button 17 to 24: Scroll Wheel (rotate it)


2. Back button 10. Stop button
3. OK button 11. HOME button
4. up cursor button 12. left function button
5. down cursor button 13. center function button

54/70
6. left cursor button 14. right function button
7. right cursor button 15. +
8. Black button 16. -

2-3) Press the OK button. The machine becomes ready for the next operation.
3) LCD data line short / open check
3-1) The RGB gradation pattern is displayed on the LCD. Visually confirm that the patterns are displayed
properly.

3-3) Press the OK button. The machine becomes ready for the next operation.
4) Color pattern check
4-1) The color pattern is displayed on the LCD. Visually confirm that the patterns are displayed properly.

4-2) Press the ON button. The machine becomes ready for the next operation. Press the ON button again to turn
off the machine.

(5) Ink absorber counter setting


Set the ink absorber counter value to a new EEPROM after the logic board is replaced in servicing.
1) Before replacement of the logic board, check the ink absorber counter value in EEPROM information print.
2) After replacement of the logic board, the ink absorber counter value should be set in the service mode using
the Service Tool.
In the Ink Absorber Counter section of the Service Tool, select Main from the Absorber pull-down menu.
From the Counter Value(%) pull-down menu, select the value (in 10% increments) which is the closest to
the actual counter value confirmed before replacement of the logic board, and click Set.
3) Print EEPROM information to confirm that the value is properly set to the EEPROM.

55/70
(7) Capacitive sensor sensitivity setting
Adjust the level of sensitivity of the capacitive sensors used for the operation panel.
To examine sensitivity, perform (4) Button and LCD test.
1) In the Panel Rank section of the Service Tool, select the rank and click Set.
- When the sensitivity is low (the panel is slow to respond), select "0" (zero).
- When the sensitivity is high (the panel is quick to respond), select "3."

For reference:
- Measure the sensitivity as follows:
Put your finger 2 mm above the panel. If the panel responds, no change to the rank is necessary.
If the panel responds when your finger is 3 mm or more above the panel, set the rank to "3."
If the panel does not respond even if you touch the panel, set the rank to "0."
- In the service part logic board, the rank is set to "0."
- The ranks 0 to 2 use the same correction table, thus there will be no difference in sensitivity from
"0" to "2."

<3-1. Adjustment>
<3-2. Adjustment and Maintenance in Service Mode>
<3-3. Adjustment and Settings in Service Mode>

56/70
MG8100 series --- 4. ADJUSTMENT / SETTINGS TABLE OF CONTENTS

3-4. Grease Application


Grease Number of
Where to apply Drawing
No Part name Grease amount drops x
grease / oil No.
(mg) Location
The surface where the Floil
1 Carriage rail (1) 230 to 290 ---
carriage unit slides KG107A
The surface where the Floil
2 Carriage rail (2) 180 to 220 ---
carriage unit slides KG107A
The surface where the Floil
3 Carriage rail (3) 180 to 220 ---
carriage unit slides KG107A
The surface where the Floil
4 Carriage upper rail (4) 230 to 290 ---
carriage slider moves KG107A
APP code wheel gear
Floil
5 APP code wheel gear shaft sliding portion (the (5) 9 to 18 1x1
KG107A
entire surface)

1 drop = 9 to 18 mg

57/70
3-5. Special Notes on Servicing
(1) For smeared printing, uneven printing, or non-ejection of ink
When smeared printing, uneven printing, or non-ejection of ink occurs, print the nozzle check pattern to determine
58/70
whether the print head is faulty or not.
< Procedures >
1) Examine the ink tank conditions.
- Is the outer film completely removed to open the air-through?
- Re-install the ink tanks.
- Is the ink tank Canon-genuine or not?
- Is the ink tank refilled one or not?
2) Remove and clean any foreign material from the caps of the purge unit.
3) Perform print head cleaning or deep cleaning.
4) Perform print head alignment.
5) Print the nozzle check pattern.
6) If the nozzle check pattern is not printed properly, the print head may be faulty. Perform troubleshooting
while referring to the Print Head Workshop Manual or the Print Head Service Manual, 1-4. Troubleshooting.
Manual name No. Form Price (JPY)
Print Head Workshop Manual QY8-9120-D0C CD-ROM 50,000
Print Head Service Manual QY8-9121-D0C CD-ROM 30,000

(2) Paper feed motor adjustment


1) When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by
the blue arrow in the photo below).
2) After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print
operation (due to dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.

The screws securing the paper feed motor may be loosened only at replacement of the paper
feed motor unit. DO NOT loosen them in other cases.

(3) Carriage unit replacement


In the MG8100 series, the carriage unit can be replaced by removing only the carriage upper rail from the main
chassis (see 2-2. Part Replacement Procedures, (7) Carriage unit removal, for details).
If the lower carriage rail needs to be removed, before removing the screws, put a mark on the main chassis to
indicate the carriage rail position.
After replacing the carriage, return the carriage rail to the original position while aligning the rail to the mark on
the chassis.
59/70
(4) Document pressure sheet (sponge sheet) replacement

1) Peel off the cover sheet from the double-sided adhesive tape on the back of the document pressure sheet.
With the long-side down, position the upper-left corner of the document pressure sheet at the scanning
reference point on the platen glass (back left where the red lines cross in the photo above).
2) Slowly close the document pressure plate with the FAU (document pressure plate frame) attached to it, while
maintaining the hinge position. The document pressure sheet will attach to the plate frame.
3) Open the plate to confirm the following:
- No extension of the sponge edges over the mold part of the upper scanner cover.
- No gap between the platen glass reference edges and the corresponding sponge edges.
- No shades or streaks in monochrome test printing without a document on the platen glass.

(5) Ink absorber counter setting


Before replacement of the logic board, check the ink absorber counter value, and register it to the replaced new
logic board. (The value can be set in 10% increments.)
In addition, according to the "Guideline for Preventive Replacement of Ink Absorber," replace the ink absorber.
When the ink absorber is replaced, reset the applicable ink absorber counter (to 0%). See 3-3. Adjustment and
Settings in Service Mode.

(6) Preventive replacement of ink absorber


Replace the ink absorber in accordance with the "Guideline for Preventive Replacement of Ink Absorber" even
when the ink absorber is not full. (Related Service Information #Q-12E/J-0188)

< Guideline for preventive replacement of ink absorber >


Replace the ink absorber when it falls in either Criteria 1 or Criteria 2.

Criteria Purpose How to know the criteria values


Criteria 1: To avoid re-repair for ink For 2009 2H or earlier products:
The ink absorber life* is 2 absorber replacement in a short EEPROM information print and the
years or less. period of time after repair for quick reference table (Service
other reasons. Information #Q-12E/J-0188)

For 2010 1H and later products:

60/70
EEPROM information print
Criteria 2: To prevent ink leakage during EEPROM information print
The ink absorber counter return of the repaired printer to
value is 80% or more. users.
* The estimated number of months until the ink absorber will become full

< How to judge >


Print the EEPROM information, and check the "D" (ink absorber counter) and "DF" (ink absorber life) values.
Step 1: Is "D" 80% or more?
Yes (80% or more) -> Replace the ink absorber.
No (less than 80%) -> Proceed to Step 2.
Step 2: Is "DF" 24 or more?
No (less than 24 months) -> Replace the ink absorber.
Yes (24 months or more) -> No need to replace the ink absorber.
Note: If the "ST" (installation date) value is 2010/07 or earlier, the "DF" (ink absorber life)
value may not be correct. Skip Step 2. The ink absorber life is an estimated value
calculated based on the user's machine usage.

< How to read the EEPROM information print >

<3-4. Grease Application & 3-5. Special Notes on Servicing>

61/70
MG8100 series TABLE OF CONTENTS

4. VERIFICATION AFTER REPAIR

4-1. Standard Inspection Flow


In each step below, confirm that printing is performed properly and the machine operates properly without any strange noise.

EEPROM information print


<Check point>
- The information must be printed properly.

<Additional verification to be made> See 2-1. Major Replacement Parts and Adjustment.
- At logic board replacement
- At ink absorber replacement
- At platen unit or spur unit replacement
- At document pressure plate unit, document top cover unit, or LCD viewer unit replacement
- At wireless LAN board replacement
Integrated inspection pattern print
<Check point>
- The pattern must be printed properly.

Copy function
<Check point>
- Copying must be performed properly.

<Additional verification to be made> See 2-1. Major Replacement Parts and Adjustment.
- At document pressure sheet or scanner unit replacement
Communication with a connected computer
<Check point>
- Via USB connection to the computer, printing from the computer must be performed properly
(paper feeding from the rear tray and from the cassette respectively).

<Additional verification to be made>


- For repair of a specific problem, confirm the applicable specific function in the user mode.
PictBridge, IrDA communication, Bluetooth communication, LAN, Copy, Scan,
Scan-to-Memory function, Film scanning, Film copying, Card Direct printing

Wired / Copy, Scan, Scan-


PictBridge, IrDA, Card
Wireless to-Memory, Film
Bluetooth Direct
LAN scanning or copying

Power-off in the service mode


<Check point>
- The paper lifting plate must be in the raised position.

External and internal appearance


<Check point>
- No grease, oil, or smearing on the timing slit strip film.
- No lifting of the platen ink absorber.
- No foreign material or dislocation of any part inside the printer.
- No damage or scratches that will affect the functionality.
Packaging
<Check point> See 6. MACHINE TRANSPORTATION.
- The carriage must be locked in the home position.
62/70
4-2. Integrated Inspection Pattern Print
< Print sample >

63/70
4-3. Ink Absorber Counter Value Print
<Print sample>

<4. VERIFICATION AFTER REPAIR>

64/70
MG8100 series TABLE OF CONTENTS

5. APPENDIX

5-1. Customer Maintenance


Approx.
Adjustment Timing Purpose Tool
time
Automatic - At print head replacement To ensure accurate - Machine buttons 5 min.
print head - When print quality is not dot placement. - 1 sheet of MP-101
alignment satisfying (uneven printing, - Computer (printer driver)
etc.)
Manual print - At print head replacement To ensure accurate - Machine buttons 10 min.
head alignment - When print quality is not dot placement. - Computer (printer driver)
satisfying (uneven printing,
etc.)
Print head When print quality is not To improve nozzle - Machine buttons 1 min.
cleaning satisfying. conditions. - Computer (printer driver)
Print head deep When print quality is not To improve nozzle - Machine buttons 2 min.
cleaning satisfying, and not improved conditions. - Computer (printer driver)
by print head cleaning.
Ink tank When an ink tank becomes To replace the empty --- 1 min.
replacement empty. ("No ink error" ink tank.
displayed on the monitor or
on the machine LCD, or short
flashing of an ink tank LED)
Paper feed - When paper does not feed To clean the paper - Machine buttons 2 min.
roller cleaning properly. feed rollers of the - Computer (printer driver)
- When the front side of the selected paper
paper is smeared. source (rear tray or
cassette).
Bottom plate When the back side of the To clean the platen - Machine buttons 1 min.
cleaning paper is smeared. ribs. (Feed the paper - Computer (printer driver)
from the rear tray.)
Scanning area When the platen glass or To clean the platen Soft, dry, and clean lint- 1 min.
cleaning document pressure sheet is glass and pressure free cloth.
dirty. sheet.
Exterior When necessary To clean the Soft, dry, and clean lint- 1 min.
cleaning machine exterior, or free cloth.
to wipe off dusts.

65/70
5-2. Special Tools
Name Tool No. Application Remarks
To the carriage rail sliding portions and joint In common with other
FLOIL KG-107A QY9-0057-000
of the front door and bottom case. products on the market

5-3. Sensors
No. Sensor Function Detectable problems
1 Scanner open Detects opening and closing of the - The carriage does not move to the center even
sensor scanning unit (cover). when the scanning unit is opened.
2 Scanner home Detects the operation position of the - Faulty scanner
position sensor scanner CCD module, and controls - An error during scanning
scanning operation. - Home position sensor error
- Faulty scanned or copied images
3 Inner cover sensor Detects opening and closing of the - The inner cover is open when it should be
inner cover. closed.
- The inner cover is closed when it should be
opened.
4 PE sensor Detects the leading and trailing - No paper
edges of paper. - Paper jam
5 ASF cam sensor Detects the position of the ASF cam - ASF cam sensor error
(for paper feeding from the rear - Paper feeding problem
tray).
6 APP encoder Detects rotation of the APP - APP sensor error
sensor encoder, and controls paper feeding - APP position error
(from the rear tray and from the
cassette) and purging operation.
7 Carriage encoder Detects the position of the carriage. - Carriage position error
sensor - Printing shifts from the correct position.
- Uneven printing
- Strange noise
8 Temperature & Detects the temperature of the - Internal temperature error
Ink amount sensor inside of the machine and the - Low-ink or out-of-ink warning
remaining ink amount.
9 Ink sensor Detects the position of an ink tank. - Wrong position of an ink tank
- Installation of multiple ink tanks of the same
color
- No recognition of an ink tank
10 LF encoder sensor Detects rotation of the LF encoder, - LF position error
and controls paper feeding. - Uneven printing
11 Eject encoder Detects rotation of the eject - LF position error
sensor encoder, and controls paper feeding. - Uneven printing
12 Valve cam sensor Detects the position of the purge - Valve cam sensor error
valve cam, and controls purging
operation.

66/70
13 Pump roller sensor Detects the position of the pump - Pump roller sensor error
roller, and controls purging
operation.
14 Purge cam sensor Detects the position of the purge - PG cam sensor error
main cam, and controls purging
operation.

67/70
68/70
5-4. Serial Number Location
On the inner guide over the upper portion of the spur holder (visible when the scanning unit (cover) is opened).
The photos are for the MP990 as examples.

When the machine power is OFF. When the machine power is ON.

<5. APPENDIX>

69/70
MG8100 series TABLE OF CONTENTS

6. MACHINE TRANSPORTATION

This section describes the procedures for transporting the machine for returning after repair, etc.
1) In the service mode, press the ON button to finish the mode, and confirm that the paper lifting plate of the rear
tray is raised.
2) Keep the print head and ink tanks installed in the carriage.
See Caution 1 below.
3) Turn off the machine to securely lock the carriage in the home position. (When the machine is turned off, the
carriage is automatically locked in place.)
See Caution 2 below.
4) Slide the scanner lock switch (in the red circle in the photo below) to the lock position, in order to fix the
CCD unit of the scanner in place and to protect it from vibration during transportation.

(1) If the print head is removed from the machine and left alone by itself, ink (the pigment-
based black ink in particular) is likely to dry. For this reason, keep the print head installed
in the machine even during transportation.
(2) Securely lock the carriage in the home position, to prevent the carriage from moving and
applying stress to the carriage flexible cable, or causing ink leakage, during
transportation. Make sure that the carriage is locked in place at power-off.

- If the print head must be removed from the machine and transported alone, attach the protective cap
(used when the packing was opened) to the print head (to protect the print head face from damage due
to shocks).

<6. MACHINE TRANSPORTATION>

70/70
PIXMA MG8120

PARTS
CATALOG

Canon
Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
Parts Catalog PIXMA MG8120
FIGURE 1 PACKING CONTENTS FIGURE 2 AC ADAPTER
& PRINT HEAD

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


1- 1 QM3-7589-000 CASSETTE UNIT 2- 1 QM3-7439-000 AC ADAPTER: 100V-240V 50/60HZ
2 QY6-0078-000 PRINT HEAD 2 QC3-0459-000 CAP, LAN CONNECTOR
3 QH2-2719-000 CORD, POWER 100V-120V

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
1 of 6
Parts Catalog PIXMA MG8120
FIGURE 3 EXTERNAL COVERS & FIGURE 4 DOCUMENT PRESSURE PLATE
SCANNER UNIT

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


3- 1 QM3-7574-000 SCANNER UNIT 4- 1 QC3-4845-000 LABEL, PRODUCT NAME, MG8120
2 QM3-7590-000 PAPER SUPPORT UNIT 2 QC3-4844-000 DOCUMENT WINDOW R
3 QM3-7587-000 SIDE COVER R UNIT 3 QM3-7581-000 LCD VIEWER UNIT
4 QM3-7588-000 SIDE COVER L UNIT 4 QM3-7598-000 DOCUMENT PRESSURE PLATE UNIT
5 QC3-4828-000 ARM, SCANNER SUPPORT 5 QM3-7599-000 DOCUMENT TOP COVER UNIT
6 WE8-6741-000 CORE, RING 6 QC3-4842-000 FLAPPER, LCD
7 QC3-4708-000 SPRING,FLAPPER
8 QC3-4701-000 HINGE, LCD R
9 QC3-4702-000 HINGE, LCD L
10 QC3-4766-000 RING, HINGE
11 QC3-4987-000 SHEET, LCD
12 QC3-4713-000 KEY, POWER
13 QM3-7472-000 POWER SW HARNESS ASS’Y
14 QK1-6727-000 CABLE, PANEL 1
15 QK1-6729-000 CABLE, PANEL 2
16 QM3-7651-000 LAMP HARNESS ASS’Y
17 QM3-4503-000 FILM GUIDE UNIT
18 QC3-4791-000 FRAME, DOCUMENT PRESSURE PLATE
19 QC3-1271-000 SHEET, DOCUMENT PRESSURE
20 KE2-5096-000 TAPE, DOUBLE SIDE
21 QZ7-0065-000 TAPE, DOUBLE STICK

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
2 of 6
Parts Catalog PIXMA MG8120
FIGURE 5 MAIN CASE UNIT & FIGURE 6 BOTTOM CASE &
FRONT DOOR UNIT INK ABSORBERS

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


5- 1 QM3-4762-000 REAR GUIDE UNIT 6- 1 QM3-7593-000 FRONT DOOR LINK UNIT
2 QM3-7585-000 MAIN CASE UNIT 2 QC2-7534-000 PAPER SEPARATION SLOPE
3 QM3-7586-000 FRONT DOOR UNIT 3 QC2-7533-000 PAPER SEPARATION KNURL
4 QM3-7640-000 DC HARNESS ASS’Y
5 QC2-7716-000 FLAPPER, DUPLEX PAPER FEED
6 QC2-7708-000 ROLLER, CASSETTE FEED PRESSURE
7 QC2-9243-000 SPRING, COIL
8 QC2-7529-000 CASSETTE RAIL L
9 QM3-3640-000 CASSETTE RAIL R UNIT
10 QC2-7654-000 GEAR, PICK UP SHAFT
11 QM3-6794-000 PICK UP ARM UNIT
12 QC2-9286-000 SHEET, INK ABSORBER
13 QY5-0233-02A ABSORBER KIT
14 QY5-0233-02B ABSORBER KIT
15 QC3-4839-000 CASE, BOTTOM
16 QC1-6457-000 FOOT, RUBBER
17 QC2-9287-000 SHEET, ANTISTATIC
18 QC2-5330-000 TAPE, DOUBLE SIDE

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
3 of 6
Parts Catalog PIXMA MG8120
FIGURE 7 LOGIC BOARD & FIGURE 8 SHEET FEED UNIT
PE SENSOR BOARD ASS’Y

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


7- 1 QC2-7678-000 ARM, RELEASE 8- 1 QM3-5625-000 ASF UNIT
2 QM3-7387-000 INNER COVER UNIT 2 QL2-3484-000 CASSETTE FEED ROLLER UNIT
3 WE8-6741-000 CORE, RING 3 QC2-7699-000 GUIDE, CASSETTE FEED
4 QK1-6731-000 CABLE, CARD SLOT 4 QL2-3485-000 DUPLEX PAPER FEED ROLLER UNIT
5 QK1-6707-000 CABLE, PICTBRIDGE 5 QM3-6814-000 PAPER GUIDE UNIT
6 QK1-6689-000 CABLE, WIRELESS LAN 6 QC2-7743-000 SPRING, COIL
7 QC3-4809-000 HOLDER, CORE 7 QC2-7657-000 SPRING, COIL
8 QC3-4836-000 PANEL, CARD SLOT
9 QM3-7545-000 CARD BOARD ASS’Y
10 QM3-7500-000 WIRELESS LAN BOARD ASS’Y
11 QM3-6886-000 PICTBRIDGE BOARD ASS’Y
12 QM3-7584-000 LOGIC BOARD ASS’Y
13 QM3-7447-000 PE SENSOR BOARD ASS’Y
14 QK1-6648-000 CABLE, PE SENSOR
15 QK1-4990-000 CABLE, LF ENCODER
16 WE8-6719-000 CORE, RING
17 QM3-7648-000 SCANNER MOTOR RELAY HARNESS ASS’Y
18 VS1-8611-004 CONNECTOR, CABLE
19 QC2-7490-000 COVER, GAP
20 QC3-4812-000 HOLDER, W-LAN CORE

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
4 of 6
Parts Catalog PIXMA MG8120
FIGURE 9 CARRIAGE UNIT & FIGURE 10 PLATEN UNIT &
PRESSURE ROLLER UNIT SPUR UNIT

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


9- 1 QC3-5524-000 SPRING, COIL 10- 1 QC2-7745-000 SPRING, COIL
2 QC3-3938-000 FILM, TIMING SLIT STRIP 2 QC2-7782-000 SPRING, COIL
3 QM3-7526-000 CARRIAGE UNIT 3 QC2-7526-000 BELT, PAPER FEED
4 QC2-7739-000 HOLDER, CARRIAGE CABLE 4 QL2-3253-000 PAPER FEED ROLLER UNIT
5 QC2-9235-000 COVER, CARRIAGE CABLE 5 QC3-4870-000 BUSHING, PAPER FEED ROLLER
6 QL2-2534-000 PULLEY HOLDER UNIT 6 QC3-3925-000 FILM, TIMING SLIT DISK FEED
7 QC1-6202-000 SPRING, COIL 7 QC3-3926-000 FILM, TIMING SLIT DISK EJECT
8 QK1-1500-000 MOTOR, CARRIAGE 8 QM3-7600-000 PLATEN UNIT
9 QC2-7528-000 SPRING, TORSION 9 QC3-4610-000 ABSORBER, INK
10 QC2-7571-000 SPRING, COIL 10 QM3-7596-000 SPUR UNIT
11 QM3-6870-000 PRESSURE ROLLER UNIT 11 QC2-9232-000 GUIDE, INNER

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
5 of 6
Parts Catalog PIXMA MG8120
FIGURE 11 PURGE SYSTEM DRIVE UNIT &
SWITCH SYSTEM UNIT

NUM. PART # DESCRIPTION NUM. PART # DESCRIPTION


11- 1 QC2-7787-000 SPRING, COIL
2 QM3-7594-000 PURGE DRIVE SYSTEM UNIT
3 QC2-9212-000 TUBE, INK JOINT
4 QC2-7483-000 TUBE, INK
5 QM3-6793-000 PURGE MOTOR UNIT
6 QC2-7652-000 GEAR, APP CODEWHEEL
7 QC2-9226-000 FILM, TIMING SLIT DISK APP
8 QM3-7642-000 MOTOR MULTI HARNESS ASS’Y
9 QM3-7644-000 PAPER FEED RELAY HARNESS ASS’Y
10 QM3-7537-000 SWITCH SYSTEM UNIT
11 QK1-3849-000 MOTOR, PAPER FEED
12 QM3-7488-000 PAPER FEED MOTOR HARNESS ASS’Y
13 QM3-4411-000 TIMING SENSOR UNIT
14 QC2-7682-000 GEAR, IDLER
15 QM3-7436-000 GND HARNESS ASS’Y
16 QC2-9216-000 SPRING, LEAF

Copyright © 2010, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
6 of 6

You might also like