Zytel FR50 NC010 A

PRODUCT INFORMATION
DuPont™ Zytel® FR50 NC010A

NYLON RESIN
Product Information
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature
performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to
create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option,
incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
Zytel® FR50 NC010A is a 25% glass fiber reinforced, flame retardant polyamide 66 resin for injection molding.
General information Value Unit Test Standard

Resin Identification PA66-GF25FR(17) - ISO 1043
Part Marking Code PA66-GF25FR(17) - ISO 11469
Rheological properties dry / cond Unit Test Standard
Molding shrinkage, parallel 0.3 / * % ISO 294-4, 2577
Molding shrinkage, normal 0.8 / * % ISO 294-4, 2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 10640 / 7500 MPa ISO 527-1/-2
Stress at break 170 / - MPa ISO 527-1/-2
Strain at break 2.5 / - % ISO 527-1/-2
Flexural Modulus 9450 / - MPa ISO 178
Charpy impact strength, 73°F 40 / - kJ/m² ISO 179/1eU
Charpy notched impact strength ISO 179/1eA
73°F 11.3 / - kJ/m²
-40°F 10.8 / - kJ/m²
Thermal properties dry / cond Unit Test Standard
Melting temperature, 18°F/min 261 / * °C ISO 11357-1/-3
Glass transition temperature, 18°F/min 80 / - °C ISO 11357-1/-2 DS
Temp. of deflection under load ISO 75-1/-2
260 psi 246 / * °C
65 psi 256 / * °C
Coeff. of linear therm. expansion, parallel 19 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 100 / * E-6/K ISO 11359-1/-2
Thermal conductivity of melt 0.22 W/(m K) -
Spec. heat capacity of melt 1660 J/(kg K) -
RTI, electrical UL 746B
30mil 130 / * °C
60mil 130 / * °C
120mil 130 °C
RTI, impact UL 746B
30mil 105 °C
60mil 115 / * °C
120mil 115 °C
RTI, strength UL 746B
30mil 105 °C
60mil 115 / * °C
120mil 120 °C
DS: Derived from similar grade
Flammability dry / cond Unit Test Standard
Burning Behav. at 60mil nom. thickn. V-0 / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
Revised: 2016-06-28 Page: 1 of 9

To find out more, visit DuPont Performance Polymers or contact nearest DuPont location.
North America Asia Pacific Europe/Middle East/Africa
Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
Copyright 2014 DuPont. The DuPont Oval Logo is a trademark or registered trademark of E.I. du Pont de Nemours and
Company or its affiliates. All rights reserved.
NYLON RESIN
UL recognition yes / * - UL 94
Burning Behav. at thickness h V-0 / * class IEC 60695-11-10
Burning Behav. 5V at thickness h 5VA / * class IEC 60695-11-20
Oxygen index 35 / * % ISO 4589-1/-2
Glow Wire Flammability Index IEC 60695-2-1/2
30mil 960 / - °C
60mil 960 / - °C
120mil 960 / - °C
Glow Wire Ignition Temperature IEC 60695-2-1/3
30mil 900 /- °C
60mil 900 /- °C
120mil 930 /- °C
Flammability, 3.0mm V-0 /* - IEC 60695-11-10
FMVSS Class B - ISO 3795 (FMVSS 302)
Burning rate, Thickness 1 mm <100 mm/min ISO 3795 (FMVSS 302)
Electrical properties dry / cond Unit Test Standard
Relative permittivity, 1MHz 3.8 / - - IEC 60250
Dissipation factor IEC 60250
100Hz 180 / - E-4
1MHz 180 / - E-4
Volume resistivity >1E13 / - Ohm*m IEC 60093
Electric strength 38 / - kV/mm IEC 60243-1
Comparative tracking index
Comparative tracking index 285 / - - IEC 60112
CTI, 23°C 2/- PLC UL 746A
Other properties dry / cond Unit Test Standard
Humidity absorption, 80mil 0.7 / * % Sim. to ISO 62
Density 1600 / - kg/m³ ISO 1183
Density of melt 1400 kg/m³ -
VDA Properties Value Unit Test Standard
Emission of organic compounds 4.7 µgC/g VDA 277
Odor test 4.5 class VDA 270
Injection dry / cond Unit Test Standard
Drying Recommended yes - -
Drying Temperature 80 °C -
Drying Time, Dehumidified Dryer 2-4 h -
Processing Moisture Content ≤0.2 % -
Melt Temperature Optimum 290 °C -
Min. melt temperature 280 °C -
Max. melt temperature 300 °C -
Max. screw tangential speed 0.2 / * m/s -
Mold Temperature Optimum 100 °C -
Min. mold temperature 50 °C -
Max. mold temperature 90 °C -
Hold pressure range 50 - 100 MPa -
Hold pressure time 3 s/mm -
Ejection temperature 210 °C -
Characteristics
Processing Injection Molding
Delivery form Pellets
Additives Release agent

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
North America Asia Pacific Near East/Africa
Regional Availability
Europe South and Central America Global

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Diagrams
Viscosity-shear rate
1E4 260 °C
270 °C
280 °C
1E3
Viscosity in Pa s
1E2
1E1
1E2 1E3 1E4
Shear rate in 1/s
Shearstress-shear rate
1E6 260 °C
270 °C
280 °C
Shearstress in Pa
1E5
1E4
1E2 1E3 1E4
Shear rate in 1/s

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Stress-strain (dry)
200 -40 °C
23 °C
B 100 °C
150 °C
B - Break
150
B
Stress in MPa
100
50
0
0 1 2 3 4
Strain in %

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Secant modulus-strain (dry)
10000 -40 °C
23 °C
100 °C
150 °C
B - Break
8000
B B
Secant modulus in MPa
6000
4000
B
2000
B
0
0 1 2 3 4
Strain in %

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Specific volume-temperature (pvT)
0.72 0.1 MPa

40 MPa
120 MPa
200 MPa
0.7
Spec. volume in E-3 m³/kg
0.68
0.66
0.64
0.62
0.6
0 50 100 150 200 250 300
Temperature in °C

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Chemical Media Resistance
Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)
Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C)
Toluene (23°C)
iso-Octane (23°C)
Ketones
Acetone (23°C)
Ethers
Diethyl ether (23°C)
Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)
Standard Fuels
ISO 1817 Liquid 1 - E5 (60°C)
ISO 1817 Liquid 2 - M15E4 (60°C)
ISO 1817 Liquid 3 - M3E7 (60°C)
ISO 1817 Liquid 4 - M15 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575
NYLON RESIN
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)
Sodium Carbonate solution (2% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)
Other
Ethyl Acetate (23°C)
Hydrogen peroxide (23°C)
DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)
50% Oleic acid + 50% Olive Oil (23°C)
Water (23°C)
Water (90°C)
Phenol solution (5% by mass) (23°C)
Symbols used:
possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and
expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).
not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast
cleaning with thorough rinsing, spills, wiping, vapor exposure).
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.
ISO Mechanical properties measured at 160 mil (Hytrel® measured at 80 mil), IEC Electrical properties measured at 80 mil, all ASTM properties
measured at 120 mil, and test temperatures are 73°F unless otherwise stated.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls within
the normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not be
used to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding that
those using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since conditions of product use
and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this
information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a
license to operate or a recommendation to infringe on patents. Caution: Do not use in medical applications involving permanent implantation in
the human body. For other medical applications, discuss with your DuPont customer representative and read Medical Caution H-50103-4.
Copyright © 2016 DuPont or its affiliates. All Rights Reserved. The DuPont Oval Logo, DuPont™, The miracles of science™ and all products
denoted with ® or ™ are registered trademarks or trademarks of E.I. du Pont de Nemours and Company or its affiliates.

Tel: +1 302 999-4592 Tel: +81 3 5521 8600 Tel: +41 22 717 51 11
Toll-Free (USA): 800 441-0575

Zytel FR50 NC010 A

Uploaded by

Copyright:

Available Formats

Zytel FR50 NC010 A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Zytel FR50 NC010 A

Uploaded by

Copyright:

Available Formats

PRODUCT INFORMATION

DuPont™ Zytel® FR50 NC010A

General information Value Unit Test Standard

Revised: 2016-06-28 Page: 1 of 9

Revised: 2016-06-28 Page: 2 of 9

Revised: 2016-06-28 Page: 3 of 9

Shear rate in 1/s

Shear rate in 1/s

Revised: 2016-06-28 Page: 4 of 9

Revised: 2016-06-28 Page: 5 of 9

Secant modulus-strain (dry)

Revised: 2016-06-28 Page: 6 of 9

Specific volume-temperature (pvT)

0.72 0.1 MPa

Revised: 2016-06-28 Page: 7 of 9

Chemical Media Resistance

Revised: 2016-06-28 Page: 8 of 9

not recommended - see explanation

Revised: 2016-06-28 Page: 9 of 9

You might also like