Scribd Logo
Upload

Welcome to Scribd!

  • 248 views

    7.2.3.3 Packet Tracer - Configuring An IPv4 ACL On VTY Lines Instructions

    Uploaded by

    Walter Jones
    The document describes configuring an IPv4 ACL on VTY lines of a router to allow Telnet access from only one approved IP address and deny access from all other IP addresses. It provides steps to configure a numbered standard ACL permitting the approved IP address, apply the ACL to VTY lines 0-15 using the access-class command, and verify the ACL is properly configured and working as intended.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    7.2.3.3 Packet Tracer - Configuring An IPv4 ACL On VTY Lines Instructions

    Uploaded by

    Walter Jones
    248 views2 pages
    The document describes configuring an IPv4 ACL on VTY lines of a router to allow Telnet access from only one approved IP address and deny access from all other IP addresses. It provides steps to configure a numbered standard ACL permitting the approved IP address, apply the ACL to VTY lines 0-15 using the access-class command, and verify the ACL is properly configured and working as intended.

    Original Title

    7.2.3.3 Packet Tracer - Configuring an IPv4 ACL on VTY Lines Instructions

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes configuring an IPv4 ACL on VTY lines of a router to allow Telnet access from only one approved IP address and deny access from all other IP addresses. It provides steps to configure a numbered standard ACL permitting the approved IP address, apply the ACL to VTY lines 0-15 using the access-class command, and verify the ACL is properly configured and working as intended.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    248 views2 pages

    7.2.3.3 Packet Tracer - Configuring An IPv4 ACL On VTY Lines Instructions

    Uploaded by

    Walter Jones
    The document describes configuring an IPv4 ACL on VTY lines of a router to allow Telnet access from only one approved IP address and deny access from all other IP addresses. It provides steps to configure a numbered standard ACL permitting the approved IP address, apply the ACL to VTY lines 0-15 using the access-class command, and verify the ACL is properly configured and working as intended.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Packet Tracer - Configuring an IPv4 ACL on VTY Lines

    Topology

    Addressing Table

    Device Interface IP Address Subnet Mask Default Gateway

    Router F0/0 10.0.0.254 255.0.0.0 N/A


    PC NIC 10.0.0.1 255.0.0.0 10.0.0.254
    Laptop NIC 10.0.0.2 255.0.0.0 10.0.0.254

    Objectives
    Part 1: Configure and Apply an ACL to VTY Lines
    Part 2: Verify the ACL Implementation

    Background
    As network administrator, you must have remote access to your router. This access should not be available to
    other users of the network. Therefore, you will configure and apply an access control list (ACL) that allows PC
    access to the Telnet lines, but denies all other source IP addresses.

    Part 1: Configure and Apply an ACL to VTY Lines


    Step 1: Verify Telnet access before the ACL is configured.
    Both computers should be able to Telnet to the Router. The password is cisco.

    Step 2: Configure a numbered standard ACL.


    Configure the following numbered ACL on Router.
    Router(config)# access-list 99 permit host 10.0.0.1

    © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 2
    Packet Tracer - Configuring an ACL on VTY Lines

    Because we do not want to permit access from any other computers, the implicit deny property of the access
    list satisfies our requirements.

    Step 3: Place a named standard ACL on the router.


    Access to the Router interfaces must be allowed, while Telnet access must be restricted. Therefore, we must
    place the ACL on Telnet lines 0 through 4. From the configuration prompt of Router, enter line configuration
    mode for lines 0 – 4 and use the access-class command to apply the ACL to all the VTY lines:
    Router(config)# line vty 0 15
    Router(config-line)# access-class 99 in

    Part 2: Verify the ACL Implementation


    Step 1: Verify the ACL configuration and application to the VTY lines.
    Use the show access-lists to verify the ACL configuration. Use the show run command to verify the ACL is
    applied to the VTY lines.

    Step 2: Verify that the ACL is working properly.


    Both computers should be able to ping the Router, but only PC should be able to Telnet to it.

    © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 2

    You might also like