Installation Viper 5101

Remote Start Keyless Entry
Model 5101
Installation Guide
This product is intended for installation by a professional

installer only! Attempts to install this product by a person other than a
trained professional may result in severe damage to a vehicle’s electrical
system and components.
© 2008 Directed Electronics, Vista, CA

N4102V 2008-09
Bitwriter®, Code Hopping™, Doubleguard®, ESP2™, Fail-
Safe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance
Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®,
Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn
Away® are all Trademarks or Registered Trademarks of Directed
Electronics.
The Bitwriter® (p/n 998U)

requires chip version 2.6 or
newer to program this unit.
Bitwriters with date code of 6A or older require an IC upgrade

(p/n 998M). Some Bitwriters with a date code of 6B do not
require the IC upgrade. Refer to Tech Tip # 1112 for more
information. Bitwriter 2 compatible.
Contents
Warning! Safety first..........................................................................................5
What is included................................................................................................7
Installation points to remember.............................................................................7
Virtual tach...............................................................................................7
D2D.........................................................................................................8
The control center......................................................................................8
Valet® program switch...............................................................................8
Status LED.................................................................................................8
Before beginning the installation..................................................................9
After the installation...................................................................................9
Component locations and finding wires .............................................................10
Making your wiring connections........................................................................10
Primary harness (H1), 12-pin connector......................................................11
Auxiliary harness (H2), 7-pin connector......................................................11
Heavy gauge remote start, (H3) 8-pin connector..........................................12
Remote start input, 5-pin connector............................................................12
Remote start auxiliary output, 5-pin............................................................13
Door lock harness, 3-pin connector............................................................13
Wire connection guides....................................................................................14
Primary harness (H1)................................................................................14
Auxiliary harness (H2)..............................................................................20
Heavy Gauge, 8-pin connector..................................................................24
Remote start input - 5-pin connector............................................................26
Remote start auxiliary output, 5-pin............................................................28
Door lock wire diagrams..........................................................................29
Neutral safety switch interface...........................................................................30
Testing the neutral safety switch.................................................................30
Plug-in LED and valet/program switch.................................................................31
Bitwriter interface - 3-pin black plug...................................................................31
Tachometer settings..........................................................................................32
Virtual tach.............................................................................................32
Tach learning..........................................................................................33
Tach threshold On/Off.............................................................................34
D2D Jumper settings.........................................................................................34
Setting the light flash polarity.............................................................................35
Remote control Learn Routine™..........................................................................36
Remote control configuration.............................................................................39
1-way remote control...............................................................................39
Additional system features.................................................................................40
System features learn routine.............................................................................40
Feature menus.................................................................................................43
Menu 1 - Keyless entry ............................................................................43
Menu 2 - Convenience ............................................................................44
Menu 3 - Remote start .............................................................................45
Feature descriptions..........................................................................................46
Menu 1 - Keyless entry ............................................................................46
Menu 2 - Convenience ............................................................................48
Menu 3 - Remote start .............................................................................51
Bitwriter®. .............................................................................................54
Shutdown diagnostics.......................................................................................56
Remote starting diagnostics...............................................................................57
Remote start safety check..................................................................................58
Troubleshooting...............................................................................................59
Keyless entry system.................................................................................59
Remote start ...........................................................................................59
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed Electronics dealer.
• When properly installed, this system can start the vehicle via a command
signal from the remote control. Therefore, never operate the system in an
area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, autho-
rized Directed Electronics dealers should:
• Never use a test light or logic probe when installing this
unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without
ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having
the vehicle serviced, the remote start system must be disabled using the
installed toggle switch. It is the user’s sole responsibility to properly handle
and keep out of reach from children all remote controls to assure that the
system does not unintentionally remote start the vehicle.
USER MUST INSTALL A CARBON MONOXIDE DETECTOR
IN OR ABOUT THE LIVING AREA ADJACENT TO THE VE-
HICLE. ALL DOORS LEADING FROM ADJACENT LIVING AR-
EAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. Except when performing
the Safety Check outlined in this installation guide, (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user will be responsible for having the neutral safety fea-
ture of the vehicle periodically checked, wherein the vehicle must not remotely
start while the car is in gear. This testing should be performed by an authorized
Directed Electronics dealer in accordance with the Safety Check outlined in
this product installation guide. If the vehicle starts in gear, cease remote start
operation immediately and consult with the user to fix the problem immediately.
© 2008 Directed Electronics. All rights reserved. 5

After the remote start module has been installed, test the remote start module
in accordance with the Safety Check outlined in this installation guide. If the
vehicle starts when performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The remote start module must
be removed or properly reinstalled so that the vehicle does not start in gear. All
installations must be performed by an authorized Directed Electronics dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-
ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RE-
SULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE
THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED RE-
MOTE START MODULE. DIRECTED ELECTRONICS, INC. WILL NOT BE HELD
RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly
installed and operated. When testing to ensure the installation is working prop-
erly, only remote start the vehicle in neutral gear, on a flat surface and with a
functional, fully engaged parking brake. Do not allow anyone to stand in front
of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top
with a manual transmission. Installation in such vehicles may pose certain risk.
6 © 2008 Directed Electronics. All rights reserved.

What is included
• The control module
• Control center with integrated status LED and Valet Override switch (p/n
6111T)
• Two five-button /1-way Supercode Remote (p/n 7153V)
• A shut-down toggle switch
Installation points to remember

This product is designed for fuel-injected, automatic transmission, or vehicles
with manual transmissions.
Important! The default option “Manual” is a safety precau-
tion that forces the installer to enable the Manual Transmis-
sion Start (MTS) routine or program the unit to the “Auto-
matic” option before the remote start can be activated for
the first time.
The “Automatic” option should be programmed on to work with automatic trans-

missions. When the “Manual” option is selected a specific routine is required
before exiting the vehicle to enable the MTS mode.
➤ Virtual tach
Virtual Tach is a new feature for Directed this year. It is the default RPM-sensing
method for the new hybrid keyless entry /remote start systems.
Virtual Tach gives the installer the performance of a hard wired tach wire, with
the convenience of voltage sensing. It is far superior to any voltage-sense feature
you’ve tried before.
Virtual Tach monitors the cranking voltage of the vehicle using a very fast micro
controller and an analog-to-digital converter. The microprocessor “saves” the
base voltage as a reference. When Virtual Tach “sees” the slightest uptick in
voltage, indicating that the alternator is charging the battery, the starter motor
shuts off instantly.

➤ D2D
The system has the ability to interface with an XK module through the D2D port.
The advantage to using a D2D interface is that there is less wiring involved in
the installation. Check the XK module installation guide to determine which wires
are not needed, and which options are available.
➤ The control center

The control center position should be discussed with the vehicle’s owner prior to
installation. The LED and Valet switch are housed on the control center, so make
sure the customer is satisfied with the location.
Valet switch
LED
➤ Valet® program switch

The valet/program switch is built into the control center.
Important: When the vehicle is delivered, please show the
user where this switch is located and how to disarm the system
with it.
Note: An optional valet switch (p/n #8631) is available if the onboard valet
switch is not used for the installation.
When installing the external valet switch ensure that the location has sufficient
clearance to the rear. The switch should be well hidden. It should be placed so
passengers or stored items (such as in a glove box or center console) cannot
accidentally hit it. The switch fits into a 9/32-inch hole.
➤ Status LED
The status LED is built into the control center. An optional LED (p/n 8634) is
available if the onboard LED will not be used for the install. The LED fits into a
9/32-inch hole.

➤ Before beginning the installation
• Please read this entire installation guide before beginning the installation.
The installation of this remote start system requires interfacing with many of
the vehicle’s systems. Many new vehicles use low-voltage or multiplexed
systems that can be damaged by low resistance testing devices, such as
test lights and logic probes (computer safe test lights). Test all circuits with a
high quality digital multi-meter before making connections.
• Do not disconnect the battery if the vehicle has an anti-theft-coded radio.
If equipped with an air bag, avoid disconnecting the battery if possible.
Many airbag systems display a diagnostic code through the warning lights
after the lights lose power. Disconnecting the battery causes the anti-theft
code to be erased, which can then require a trip to the dealer.
• If using an external LED or Valet Switch, check with the customer about
where to locate the switch.
• To avoid accidental battery drainage; turn off the interior lights or remove
the dome light fuse.
• Roll down a window to avoid being locked out of the car.
➤ After the installation

• Test all functions. The Using Your System section of the Owner’s Guide is
very helpful when testing.
• Review and complete the Safety Check section of this guide prior to the
vehicle reassembly.

Component locations and finding wires
For detailed information on where to locate components, and how to find the
wires you need, please refer to the Direct Tech web site at
www.directechs.com.
Making your wiring connections

Before making your connections, plan how your wires will be routed through
the vehicle. For instance, the red 12V constant input and the remote start igni-
tion wires are often routed together to the ignition switch harness. In order to
keep the wiring neat and make it harder to find, you may wish to wrap these
wires together in electrical tape or conceal them in tubing similar to what the
manufacturer used.
There are two acceptable ways of making a wire connection - solder connec
tions and crimp connectors. When properly performed, either type of connection
is reliable and trouble-free. Regardless of whether you solder your connections
or you use mechanical type crimp-on connections, ensure that all connections
are mechanically sound and that they are insulated, especially when connecting
data lines in the vehicle.
Cheap electrical tape, especially when poorly applied, is not a reliable insu-
lator. It often falls off in hot weather. Use good quality electrical tape or heat
shrink.
• Never twist-and-tape the wires together without soldering.
• Never use “fuse taps”, as they can damage fuse box terminals.
If you use tapping connectors such as T-Taps (not to be confused with Scotch-
Locks), avoid using them in higher-current applications (constant 12V, ground,
etc.) These connectors are inferior in quality and should be avoided.

➤ Primary harness (H1), 12-pin connector
H1/1 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT
H1/2 RED (+)12v CONSTANT INPUT
H1/3 BROWN (-) HORN OUTPUT
H1/4 WHITE/BROWN LIGHT FLASH ISOLATION WIRE - PIN 87a of onboard relay
H1/5 BLACK (-) CHASSIS GROUND
H1/6 VIOLET (+) DOOR TRIGGER INPUT*
H1/7 BLUE (-) FACTORY HORN INPUT**
H1/8 GREEN (-) DOOR TRIGGER INPUT*
H1/9 BLACK/WHITE (-) 200mA DOME LIGHT OUTPUT
H1/10 WHITE/BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
H1/11 WHITE PARKING LIGHT OUTPUT
H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
*Door trigger input is needed if one of the following are used: MTS, passive
arming, auto re-locking, door ajar error honk or Smart Key control.
**Not available with 1- way remote
➤ Auxiliary harness (H2), 7-pin connector

H2/1 LIGHT GREEN/ (-) 200mA FACTORY ALARM DISARM OUTPUT
BLACK
H2/2 LIGHT GREEN/ (-) 200mA FACTORY ALARM ARM OUTPUT
WHITE
H2/3 WHITE/VIOLET (-) 200mA AUX 1 OUTPUT
H2/4 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
H2/5 WHITE/BLACK (-) 200mA AUX 3 OUTPUT
H2/6 LIGHT BLUE (-) 200mA 2ND UNLOCK OUTPUT
H2/7 GRAY/BLACK (-) DIESEL WAIT TO START INPUT

There are three harness connections relative to remote start function, including
the heavy gauge and input and output harnesses.
➤ Heavy gauge remote start, (H3) 8-pin connector

H3/1 PINK IGNITION 1 INPUT/OUTPUT
H3/2 RED/WHITE (+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87
H3/3 ORANGE ACCESSORY OUTPUT
H3/4 VIOLET STARTER OUTPUT
H3/5 RED (+) FUSED (30A) IGNITION 1 INPUT
H3/6 PINK/WHITE IGNITION 2 / FLEX RELAY OUTPUT 30
H3/7 PINK/BLACK FLEX RELAY INPUT 87A key side (if required) of FLEX
RELAY
H3/8 RED/BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT
➤ Remote start input, 5-pin connector

1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT
2 VIOLET/WHITE TACHOMETER INPUT
3 BROWN (+) BRAKE SHUTDOWN INPUT
4 GRAY N/O or N/C (-) HOOD PIN SWITCH INPUT
5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT

➤ Remote start auxiliary output, 5-pin
1 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT
2 ORANGE (-) 200mA ACCESSORY OUTPUT
3 VIOLET (-) 200mA STARTER OUTPUT
4 PINK (-) 200mA IGNITION 1 OUTPUT
5 BLUE (-) 200mA STATUS OUTPUT
Note: Wires 1 - 4 on the remote auxiliary outputs are wired to the (-) triggers for
the onboard remote start relays and are not diode isolated. If connecting these
wires directly to the vehicle you must place a 1-amp diode in line to prevent
feedback from the vehicle.
➤ Door lock harness, 3-pin connector

1 BLUE (+) LOCK (-) UNLOCK OUTPUT
2 EMPTY NOT USED
3 GREEN (-) LOCK (+) UNLOCK OUTPUT

Wire connection guides
➤ Primary harness (H1)
H1/1 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT
When the system receives the code controlling trunk release output for longer
than 1.5 seconds, the red/white wire will supply an output as long as the
transmission continues. This is typically used to operate a trunk/hatch release or
other relay-driven function.
Warning! Never use this wire to drive anything but

a relay or a low-current input, supplied output is only
200mA. Connecting directly to a solenoid, motor, or
other high-current device will cause the module to fail.
H1/2 RED (+)12v CONSTANT INPUT
Before connecting this wire, remove the supplied fuse. Connect to the battery
positive terminal or the constant 12V supply to the ignition switch.
Note: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not
use the 15A fuse in the harness for this purpose. This fuse protects the module.

H1/3 BROWN (-) HORN OUTPUT
This wire supplies a (-) 200 mA output that can be used to honk the vehicle horn.
It outputs a single pulse when locking the doors with the remote, and two pulses
when unlocking with the remote. This wire also outputs pulses for 30 seconds
when Panic Mode is activated. If the vehicle has a (+) horn circuit, an optional
relay can be used to interface with the system.
H1/4 WHITE/BROWN LIGHT FLASH -ISOLATION WIRE - PIN 87a of onboard relay
This wire connects to pin 87a of the onboard light flash relay. It is used when-
ever light switch isolation on the vehicle is necessary. If the vehicle has a mul-
tiplex circuit that needs the light switch isolated, you can remove the onboard
light flash fuse and replace it with the specified resistor (paying attention to the
polarity selection).
Multiplex Lightflash Interface
Lightswitch
Replace fuse with
specified resistor value
Light Flash Fuse

Multiplex Jumper under door
wire in car
White/Brown
x Cut
White
x
To control
module in car

H1/5 BLACK (-) CHASSIS GROUND
We recommend that you do not use a factory ground. Ground all your compo-
nents to the same point in the vehicle, (preferably the kick panel). Scrape away
any paint and use a factory bolt or make your own ground with a self-tapping
screw and a star washer.
H1/6 VIOLET (+) DOOR TRIGGER INPUT*
This wire is used in vehicles that have a positive (+) switched dome light circuit.
Connect the violet wire to a wire that shows (+)12V when any door is opened,
and ground when the door is closed.

H1/7 BLUE (-) FACTORY HORN INPUT*
This optional input can be wired to the factory horn honk output of the vehicle.
When this wire receives an input for a minimum of .5 seconds, the system
reports a trigger on the remote. This is useful on vehicles that have a factory
security system, it notifies the owner that the system was triggered.
Note: The system does not report that a zone has been triggered when unlock-
ing with the remote. Connect to the wire in the vehicle that shows voltage
when the factory alarm system is triggered. If the vehicle has a (+) horn circuit,
an optional relay can be used to interface with the system, as shown below.
(-) GROUND (-) GROUND
(+)HORN CIRCUIT IN VEHICLE H1/7 BLUE
*This feature is only available with a 2-way remote upgrade.
H1/8 GREEN (-) DOOR TRIGGER INPUT*
Most vehicles use negative door trigger circuits. Connect the green wire to a
wire which shows ground when any door is opened. In vehicles with factory
delays on the dome light circuit, there is usually a wire that is unaffected by the
delay circuitry.
H1/9 BLACK/WHITE (-) 200mA DOME LIGHT OUTPUT
Connect this wire to the optional dome light supervision relay as shown below:
Important! This output is only intended to drive a relay. It cannot be connected
directly to the dome light circuit, as the output cannot support the current draw
of one or more light bulbs.
H1/10 WHITE/BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
This input comes from the factory set to 1 activation pulse. This means that it is
necessary to have a single ground pulse on the white/blue wire for the remote
start to activate or to deactivate.
The H1/10 wire can also be used to activate the Turbo Timer mode when the
car is running and this wire receives a ground.
Note: The number of activation inputs can be programmed to 1 or 2 pulses with

an optional momentary switch. This setting affects both the input wire and the
remote control when operating the remote starter.
To white/blue activation
input on system

H1/11 WHITE PARKING LIGHT OUTPUT
This wire should be connected to the parking light wire in the vehicle. See Set-
ting the light flash polarity section of this guide for polarity settings.
(+) Positive Light Flash Output

WHITE H1/11
(+) LIGHT FLASH OUTPUT
(-) Negative Light Flash Output

WHITE H1/11
(-) LIGHT FLASH OUTPUT
Note: For parking light circuits that draw 10-amps or more, the internal jumper
must be switched to a (-) light flash output. (See Setting the light flash polarity
section of this guide.) P/N 8617 or a standard automotive SPDT relay must be
used on the H1/11 light flash output harness wire.
H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
This wire supplies a (-)500 mA ground as long as the system is locked and when
the remote start is activated. (This feature can be turned off by programming the
anti-grind option Off). This output ceases as soon as the system is unlocked. The
GWA can be hooked up to an optional starter kill/anti-grind relay control mod-
ule, a voice module or any accessory that requires a ground when armed.
Note: The one time bypass feature does not disable function.

➤ Auxiliary harness (H2)
H2/1 LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT
This wire sends a negative pulse every time the remote start is activated , chan-
nel 2 is activated (programmable on/off) or when the doors are unlocked with
the remote. This can be used to pulse the disarm wire of the vehicle’s factory anti-
theft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown
in the following diagrams.
Relay for Negative (-) Relay for Positive (+)

Disarm Wire Disarm Wire
H2/2 LIGHT GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT
This wire sends a negative pulse every time the remote start shuts down or when
the doors are locked with the remote. This can be used to pulse the arm wire
of the vehicle’s factory anti-theft device. Use a relay to send a (-) or (+) pulse to
the arm wire.

H2/3 WHITE/VIOLET (-) 200mA AUX 1 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter but-
tons controlling Aux 1 channel is pressed. (See descriptions for Aux 3)
Warning! Never use this wire to drive anything

but a relay or a low-current input, supplied
output is only 200mA. Connecting directly to
a solenoid, motor, or other high-current device
will cause the module to fail.
H2/4 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter but-
tons controlling Aux 2 channel is pressed. (See descriptions for Aux 3.)

but a relay or a low-current input, supplied out-
put is only 200mA. Connecting directly to a
solenoid, motor, or other high-current device will
cause the module to fail.
H2/5 WHITE/BLACK (-) 200mA AUX 3 OUTPUT
This wire provides 200 mA programmable output whenever the transmitter

button(s) controlling Aux 3 is pressed. This output can be programmed to provide
the following types of outputs
• Validity: Output that sends a signal as long as the transmission is re-

ceived.
• Latched: Output that sends a signal when the Aux channel button is pressed
and continues until the same button is pressed.

• Latched, reset with ignition: Similar to the latched output, this type of output
turns On the first time the Aux channel button is pressed, and turns Off the
next time the same button is pressed. This type of output additionally stops
and resets whenever the ignition is turned On and then Off.
• 30 seconds timed: The output sends a continuous signal for 30 seconds.
Note: Bitwriter® programs from 1 to 90 seconds.

but a relay or a low-current input, supplied out-
put is only 200mA. Connecting directly to a
solenoid, motor, or other high-current device
will cause the module to fail.
H2/6 LIGHT BLUE (-) 200mA 2ND UNLOCK OUTPUT
This wire produces a (-) 200mA output for progressive locks in which the driver
door unlocks first and the remaining locks will unlock with a second press of the
unlock button on the remote.
Note: This feature will need to be programmed “On” to function correctly (see
System Feature Menu #1, feature 8).
H2/7 GRAY/BLACK (-) DIESEL WAIT TO START INPUT
Connect this wire to the wire in the vehicle that sends the signal to turn on the
WAIT-TO-START bulb in the dashboard. In most diesels the wire is negative
(ground turns on the bulb) and the GRAY/BLACK wire can be directly connected
to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the
bulb) a relay must be used to change the polarity.
The system has a programmable onboard timer (See Feature menu#3, feature 9)
so it is not mandatory to connect to the wait-to-start wire in the vehicle.

Note: A 1-amp diode must be installed in line on the factory wire between the
wait-to-start indicator and the ECM. (See the following diagram for details).
(+)WAIT-TO-START WIRE

➤ Heavy Gauge, 8-pin connector
There are 8 heavy gauge wires coming from the large 8-pin connector. They
are used to energize the ignition circuits in the vehicle. It is crucial to ensure that
these connections are capable of handling the current demands. For this reason,
Scotch-Locks, T-taps and other such connectors are strongly discouraged.
H3/1 PINK IGNITION 1 INPUT/OUTPUT
Connect this wire to the ignition wire in the vehicle. This wire not only supplies
voltage for the ignition line in the vehicle, it is also the ignition feed for the remote
start system.
H3/2 RED/WHITE (+) FUSED (30A) FUSED IGNITION 2 /FLEX RELAY INPUT 87
This wire is the polarity feed for the ignition 2/flex relay.
H3/3 ORANGE ACCESSORY OUTPUT
Connect this wire to the accessory wire that powers the climate control system
H3/4 VIOLET STARTER OUTPUT
Connect this wire to the starter wire in the vehicle.
H3/5 RED (+) FUSED (30A) IGNITION 1 INPUT
This wire is the polarity feed for the Ignition 1 relay.

H3/6 PINK/WHITE IGNITION 2 / FLEX RELAY OUTPUT 30
This wire is factory programmed as Ignition 2 and can be programmed as a

2nd accessory or 2nd starter.

H3/7 PINK/BLACK FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY
This wire is used when an ignition switch isolation on the vehicle is necessary.
This is common on Toyota and Nissans which required the use of Tech Tip
document #1077. (See menu # 3 Feature 8 for programming options) See the
diagram below for more wiring detail.)
H3/8 RED/BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT
This wire is the polarity feed to the accessory and starter relays.

➤ Remote start input - 5-pin connector
1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT
Connect this wire to a ground source if installing this unit in an automatic trans-
mission vehicle. If this unit is being installed in a manual transmission vehicle then
connect it to the emergency brake wire. This input MUST rest at ground in order
for the remote start system to operate.
Important! Always perform the steps outlined in Safety Check section to verify
that the vehicle cannot be started in ANY drive gear and that the override switch
is functioning properly.
2 VIOLET/WHITE TACHOMETER INPUT WIRE
This input provides the module with information about the engine’s revolutions
per minute (RPMs). It can be connected to the uncommon colored wire of the
fuel injector, the crankshaft position sensor, the camshaft position sensor or the
negative side of the coil in vehicles with conventional coils. In multi-coil and high
energy ignition systems locating a proper signal may be more difficult. Once
connected, you must teach the system the tach signal.
Note: This wire MUST be used when installing this unit on a manual transmis-
sion vehicle.
3 BROWN (+) BRAKE SHUTDOWN WIRE
This wire MUST be connected to the vehicle’s brake light wire. This is the wire
that shows (+) 12V when the brake pedal is depressed. The remote start will be
disabled or shut down any time the brake pedal is depressed.

4 GRAY N/O or N/C (-) HOOD PIN SWITCH INPUT
This wire MUST be connected to a hoodpin switch. This input will disable or shut
down the remote start when the hood is opened.
See Feature Descriptions, Menu #1 feature 11 for details about programming.
5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT
This wire supplies a 200mA output as soon as the module begins the remote start
process. The Blue/White wire can also be used to activate the defogger trigger
(latched/pulsed) 10-seconds after the remote start engages. (See the Feature
Descriptions, Menu#3, feature 11 for details about programming this output.)

➤ Remote start auxiliary output, 5-pin
These signals are provided to drive additional optional relays.
1 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT
This wire is programmed as (-) 2nd ignition output from factory and can be
programmed (to drive a relay) as a (-) starter or an accessory output. (See
Feature programming Menu 3, feature 8.)
2 ORANGE (-) 200mA ACCESSORY OUTPUT
This wire works like the main accessory wire and can be used (with a relay) to
drive any additional accessory circuits in the vehicle.
3 VIOLET (-) 200mA STARTER OUTPUT
This wire works like the starter wire and can be used (with a relay) to drive any
additional starter circuits in the vehicle.
4 PINK (-) 200mA IGNITION 1 OUTPUT
This wire works like the ignition 1 wire and can be used (with a relay) to drive
any additional ignition circuits in the vehicle.
Note: Wires 1 - 4 on the remote start auxiliary outputs are wired to the (-) triggers
for the onboard remote start relays and are not diode isolated. If connecting
these wires directly to the vehicle you must place a 1-amp diode in line to pre-
vent feedback from the vehicle.
5 BLUE (-) 200mA STATUS OUTPUT
This wire supplies an output as soon as the module begins the remote start pro-
cess. It can be used to activate a bypass module or power the key sense wire
in most vehicles to disarm the factory alarm without unlocking.
Note: Check vehicle information to verify if a bypass module is needed or if the
key sense wire is needed.

➤ Door lock wire diagrams
Important: Depending on the vehicle, the door locks may be con-

trolled by an optional data bus expansion module. If so, no door
lock interface wiring is required.
There are eight different types of door lock systems (Type A - H).
Type A: Three-wire (+) pulse controlling factory lock relays.
Type B: Three-wire (-) pulse controlling factory lock relays.
Type C: Direct-wired reversing-polarity switches. The switches are wired directly

to the motors. This type of system has no factory relays.
Type D: Adding one or more aftermarket actuators. These include central locking
systems without an actuator in the driver’s door, but with factory actuators in all
the other doors.
Type E: Electrically-activated vacuum systems.

Type F: One-wire system - cut to lock, ground to unlock.
This is a very rare system found mainly in early 90’s imports and some newer
Hyundais.
Type G: Positive (+) multiplex. One wire controls lock and unlock using resis-
tors).
Type H: Negative (-) multiplex. Same as Type G system, but uses (-) pulse in-
stead.
Note: You can use a 456L door lock learn module for Type G and H, instead of
relays and resistors. For additional information and wiring diagrams see Docu-
ment 1041 at www.directechs.com under the Resource tab.

Neutral safety switch interface
Some vehicles do not have an electrical neutral safety switch. Instead, the ve-
hicle has a mechanical neutral safety switch that physically interrupts the starter
wire and is used when the vehicle is in any drive gear. If the remote start is
interfaced before this switch, it will provide protection from starting in gear.
However, some vehicles combine the column shift mechanism and the mechani-
cal neutral safety switch into one mechanical part.
Note: You must complete the remote start system installation before doing the
following test. Ensure that the remote start system is functioning normally. This
includes connecting to the brake as a shut-down.
➤ Testing the neutral safety switch

1. Make sure there is adequate clearance to the front and rear of the
vehicle because it may move slightly.
2. Make sure the hood is closed and there are no remote start shut-downs
active.
3. Set the emergency brake.
4. Turn the key to the “run” position, this will release the shifter.
5. Place the car in drive (D).
6. Place your foot directly over the brake pedal, but do not depress it. Be
ready to step on the brake if the starter engages.
7. Activate the remote start system.
8. If the starter engages, immediately depress the brake to shut the remote
start system down. If the starter does not engage, no additional safety
system is required.
If the starter engages and the vehicle is a General Motors product or
Dodge Dakota pickup, you can find an alternative shut-down method
to prevent the starter from engaging. Refer to www.directechs.com for
Document 1008 under the Resource tab. If the vehicle is not a General
Motors product or a Dodge Dakota pickup, please call Directed Electron-
ics Technical Support for an alternative shut-down method.
Do not return the vehicle to the customer until this feature is properly
installed!

Plug-in LED and valet/program switch
The LED and valet switch are incorporated into the control center the LED line
will plug into the white 2-pin port and the Valet switch line will plug into the blue
2-pin port.
Note: Onboard LED and valet switch can be substituted with an optional out-
board LED (P/N 8634 for Blue LED and 8633 for red LED) and an outboard
valet switch (P/N 8631).
Bitwriter interface - 3-pin black plug

The black 3-pin port is provided for programming the unit using the Bitwriter
(p/n 998T). When using the Bitwriter, it is possible to configure any and all of
the programmable functions as well as lock the Remote Control and System Fea-
tures Learn Routines so that unauthorized users cannot change the configuration
or program remote controls to the unit.
When the learn routines have previously been programmed using the
Bitwriter, they may have been locked. Before proceeding with repro-
gramming the learn routines, they must be unlocked with the Bitwriter
- this cannot be done manually with the Valet switch.
Note: Bitwriters require software v2.6. Bitwriters with date code of 6A or older
require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do
not require the IC upgrade, refer to Tech Tip # 1112 for more information.
Bitwriter 2 compatible.

Tachometer settings
➤ Virtual tach
To program Virtual Tach:
1. After the install is complete, remote start the car.

2. If the car does not start on the first attempt, let the remote start attempt
again.
3. Once the car starts, let it run until the parking lights come on.
4. When the parking lights come on, shut off the remote start with the remote
- that's it! Virtual Tach is programmed.
To reset Virtual Tach, go into the remote programming grid and choose option
#4. Virtual Tach cannot be reset with the Bitwriter.
Note: Virtual Tach cannot be used in MTS Manual Transmission Mode.
Virtual Tach handles disengaging the starter motor during remote starting – it
does not address over-rev. If the customer wants to have the over-rev protection
capability the tach wire must be connected. This may involve more installation
shop charges than initially quoted.
Important: If the Virtual Tach mode over cranks or doesn't

crank the vehicle long enough to start and run the car, use the
Bitwriter to add or subtract the starter output time. You can
adjust the output time in increments of 50mSec of the learned
time using the Bitwriter.

➤ Tach learning
To learn the tach signal:
1. Start the vehicle with the key.
2. Within 5 seconds, press and hold the Valet/Program

switch.
3. After 3 seconds the LED light comes on when the tach

signal is learned.
4. Release the Valet/Program switch.

➤ Tach threshold On/Off
In most cases, this jumper can be left in the Off position. Some new vehicles use
less than 12 volts in their ignition systems. The unit may have trouble learning the
tach signal in these vehicles. Changing the jumper to the On setting changes
the trigger threshold of the digital tach circuit so that it will work with these type
vehicles.
D2D Jumper settings

The security system has the ability to work with a compatible module through
the D2D lines. There are two settings: one for using an internal docking module,
(p/n 400N) or an external module.
Jumpers
Jumper settings when using

an onboard D-2-D module
Jumper settings when using

an external D-2-D module
Jumpers

Setting the light flash polarity
Light flash (+) / (-) polarity
The internal fuse is used to determine the light flash output. In the (+) position, the
onboard relay will output (+)12V on the WHITE wire, H1/11. In the (-) position,
the on-board relay will supply a (-) output When wiring into a multiplex circuit,
you can replace the fuse with a resistor (paying attention to the polarity setting).
(Refer to diagram on p.15, H1/4 White/ Brown wire description).
Note: For parking light circuits that draw 10 amps or more, the internal jumper
must be switched to a (-) light flash output. P/N 8617 or a standard automotive
SPDT relay must be used on the H1/11 light flash output harness wire.
(Light Flash Fuse Jumper is under

access door - use needle nose pliers to
change fuse position)
Access door

Remote control Learn Routine™
The system comes with two 1-way remote controls already programmed to the
system. The system can store up to 4 different remote control codes in memory.
The remote uses a Supercode Protocol and requires setup before programming
the system.
If you want to program a new remote to the system follow the procedures
below
To enter the remote setup mode on the remote:
1. Hold the button on the remote until the transmit LED lights solid (approxi-
mately 10 seconds).
2. Press and hold the button until the remote LED blinks three times, and
AUX
the amber Transmit LED lights up.

3. Next enter the remote control learn routine and choose the func-
tion for “auto learn configuration” listed on the program grid.
Note: You do not need to go through the setup for the other features in the
menu.
After entering the setup mode on the remote, use the following learn routine to
add remote controls to the system.
The learn routine may be locked if previously programmed using the Bitwriter®.
If the horn generates one long honk when attempting to program the unit, the
learn routine is locked and must be unlocked using the Bitwriter® before pro-
ceeding.

The Valet/Program switch, plugged into the blue port, is used for programming.
There is a basic sequence to remember whenever programming this unit: Key,
Choose, Transmit and Release.
1. Insert the key. Turn the ignition to the ON

position. The heavy gauge pink wire must be con-
nected.
2. Choose. Within 10 seconds, press and release the

Program switch corresponding to the number of
the desired function step listed in the following table.
Once you have selected the function step, press the switch once more and hold
it. The LED flashes and the horn honks to confirm the selected functional step. Do
not release the Program switch.

Step Function
1 Auto Learn Standard Configuration (default)
The auto learn configuration will automatically setup the remote
button configuration. Note: Due to the Supercode protocol, you
cannot change the configuration.
2 Delete remotes: This feature will erase all remotes from the memory
of the system. This is useful in cases when a customer’s remote is
lost or stolen. Note: Does not reset the programmed features of the
system or reset the Virtual Tach setting.
3 Reset Features: This resets all the features of the system to the fac-
tory default settings. Note: Does not delete the remotes from the
system or reset the Virtual Tach setting.
4 Virtual Tach Reset: Deletes all previously learned values for Virtual
Tach, and on the next remote start sequence the unit will begin
virtual tach initialization.Note: The “Zap” feature on the Bitwriter
does not reset the Virtual tach setting.
3.Transmit. Press the button on the remote control.

The horn honks to confirm that the code has been suc-
cessfully programmed. It is not possible to teach a
remote control button to the system more than once.
4. Advance. You can advance from one function step to

another by releasing the Valet/Program switch and tap-
ping it to advance function steps and then holding it.
Learn Routine is exited if:

• The ignition is turned off
• The program switch is pressed too many times
• More than 30 seconds elapses between steps

Remote control configuration
➤ 1-way remote control
AUX
Note: If Keypad Lock is On, press and then press to exit.
The remote control buttons that operate the features of the remote start system are
described below. The buttons will operate in this configuration when the remote
control is programmed using the Step 1 Auto-learn routine.
AUX AUX AUX AUX
Level Direct Access x1 x2 x3 x4

Button
Lock Silent Lock
Unlock Silent Unlock Valet Mode Car Finder
Remote Start Reset Timer Mode Smart Start Rear

AUX
Runtime Defogger
AUX
AUX
AAUUXX Trunk Release AUX 1 AUX 2 AUX 3
Function Shift

Additional system features
For information about Valet mode, Remote starting the vehicle, Manual transmis-
sion vehicles and Timer mode, please consult the Owner's Guide (see Using
the system and Using the remote start) on the web at www.directechs.com.
System features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to
access and change any of the feature settings using the Valet/program switch.
However, this process can be simplified by using the Bitwriter®. Any of the
settings can be changed and then assigned to one of four remote controls. This
feature is called Owner Recognition. Each time that particular remote control is
used to disarm the system, the assigned feature settings will be recalled. Owner
Recognition is only possible when programming the unit via the Bitwriter®.
If programming with the Bitwriter®, the learn routine can be locked or

unlocked. If the learn routine has previously been locked, it must be
unlocked with Bitwriter® - this cannot be done manually with the Valet
switch.
1. Ignition. Turn the ignition on, then off. (The heavy gauge
PINK wire must be connected.)
2. Select a Menu. Press and HOLD the Valet/Program

switch. (The Valet/Program switch must be plugged
into the blue port.) After three seconds the LED flashes
and horn honks one-time, indicating entry to the Basic
Features Menu. If this is the menu you want, release the
button and go on to Step 4.
If the button is not released, the program jumps to the

next menu, the LED flashes and the horn honks twice.
There are three possible menus. Select the menu you
want, then release the Valet/Program switch.

3. Select a Feature. Press and release the Valet/Pro-
gram switch the number of times corresponding
to the feature you wish to change. For example,
to access the third feature, press and release 3
times. Then press the button once more and HOLD
it. The LED flashes and horn honks the number of
times equal to the feature you have accessed.
4. Program the Feature. While holding the Valet/Pro-

gram switch, you can toggle the feature on and off
using the remote control. Pressing the button that
locks the system selects the options in increasing
order. Pressing the button that unlocks the system se-
lects the options in descending order. Pressing the
remote start button, resets the feature to the factory
default.
5. Release. Valet/program switch.
Note: Some features have more than two possible settings. Pressing or
will toggle through the two-honk and higher settings.
Once a feature is programmed:

• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete

To access another feature in the same menu:
1. Press and release the Valet/Program switch the number of times necessary
to advance from the feature you just programmed to the next one you want
to program.
2. Then press the Valet/Program switch once more and hold it.
For example, if you just programmed the third feature in the menu and you want
to program the seventh feature in the menu, press and release the Valet/Program
switch four times and then press it once more and hold it. The LED flashes and
the horn honks seven times to confirm access to the seventh feature.
To select another menu:

1. Press and hold the Valet/Program switch.
After three seconds, the unit will advance to the next menu, the LED flashes
and the horn honks, indicating which menu has been accessed.
If you just programmed features in the first menu and you want to program a
feature in the third menu, press and hold the Valet/Program switch. After three
seconds the LED flashes and the horn honks twice indicating access to the sec-
ond menu. Continue to hold the button and three seconds later the LED flashes
and the horn honks three times indicating access to the third menu.
Features in the third menu are then programmable following steps 4 through 6
of the System Features Learn Routine procedure.
The learn routine will be exited if any of the following occurs:

• The ignition is turned On
• There is no activity for 30 seconds
• The Valet/Program switch is pressed too many times

Feature menus
Default settings are indicated in bold type.
➤ Menu 1 - Keyless entry

Menu Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+
Item
1 System Active Passive Auto relock-
Locking locking ing
locking
2 Panic Mode On Ign Off only Off
3 Horn function Confirma- Confirma- Confirma- Confirma- Confirmation

tion honk tion honk tion honk tion honk honks Off,
(20mS) & (30mS) & (40mS) & (50mS) & Panic only
panic panic panic panic
4 Ign-controlled No Ign- Lock & Lock Only Unlock Only
locks locking Unlock
5 DoorLock Single Double Double Lock Double Lock

Pulses Unlock Only Only & Unlock
6 DoorLock 0.8sec 3.5 sec 0.4 sec

Output
Duration
7 2nd Unlock No 2nd 2nd unlock 2nd unlock
unlock on Ign- on Ign-
control after control with
first unlock first unlock
8 Comfort No Comfort Comfort Comfort
Closure Closure Closure 1 Closure 2
9 Hood Trigger Normally Normally

Type Open closed

➤ Menu 2 - Convenience
Menu Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+
Item
1 One-time Off On
Bypass
2 Valet Switch 1 2 3 4 5
Pulse Count
3 Door ajar On Off

Error honk
4 Ign-controlled On Off
Dome light
5 OEM Alarm On Off

Disarm w/Trk
release
6 OEM Alarm With Before Unlock Remote Start

Disarm Output Unlock Only
7 OEM Alarm 1 2
Disarm Pulses
8 Aux 1 Output Validity Latch Latch/reset/ Timed 30 secs Off

type ign
9 Aux 1 Linking No Linking Link to Arm Link to Disarm Link to Arm/ Link to Remote
disarm Start only
10 Aux 2 Output Validity Latch Latch reset/ Timed 30 secs Off

type Ign
11 Aux 2 Linking No Linking Link to Arm Link to Disarm Link to Arm/ Link to Remote
Disarm Start only
12 Aux 3 Output Validity Latch Latch reset/ Timed 30 secs Off

type Ign
13 Aux 3 Linking No Linking Link to Arm Link to Disarm Link to Arm/ Smart Key Control
Disarm (Link to Remote
Start Off)

➤ Menu 3 - Remote start
Menu Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5
Item
1 Transmission Manual Automatic
Mode
2 Engine Virtual Tach Voltage Off Tachometer
Checking
Mode
3 Cranking 0.6 sec 0.8 sec 1.0 sec 1.2 sec 1.4
Time (5)/1.6(6)/
1.8 (7)
2.0(8)4.0(9)
4 Remote Start 12 min 24 min 60 min
Runtime
5 Activation 1 2
Pulse Count
6 Turbo Mode No Turbo On 1 min On- 3 min On 5 min On 10 min
Mode
7 Timer Mode 12 min 3 min 6 min 9 min

Runtime
8 Flex Relay Ignition 2 Accessory 2 Starter 2
Function
9 Diesel Start Wait-to Start Timed 15 sec Timed 30 sec Timed 45 sec
Delay input
10 Accessory On Off
during Diesel
Start Delay
11 Status 2 Status Latch Rear Pulse Rear
Output Defogger Defogger
12 Parking Light Constant Pulsed Off
Output
13 Anti-grind On Off
Output
14 Tach Mode Normal Increase Decrease
Starter
Release
15 Vehicle temp Off On
auto report*
*with 2-way upgrade

Feature descriptions
The features of the system are described below. Features that have additional
settings that can be selected only when programming with the Bitwriter® are
indicated by the following icon:
Important: Default settings are in bold. The numbers in pa-

rentheses indicate the number of times the LED on the control
center flashes.
➤ Menu 1 - Keyless entry

1-1 Active/Passive Locking/Auto-relocking: When active locking (1) is select-
ed, the system only locks when the transmitter is used. When set to passive (2)
the system automatically locks 30-seconds after the last door is closed. To alert
the consumer of passive locking, the horn honks 20-seconds after the door is
closed. This provides the consumer with an audible warning prior to the system
actually locking. At the 30-second mark the system locks, but without the horn
honk.
When Auto re-locking (3) is On, the system re-locks the doors 30 seconds after
the system is unlocked when using the remote, and the doors on the vehicle
have not been opened. If a door is opened when the re-lock timer is active, the
auto re-lock feature is defeated until the system sees another unlock command
from the remote.
Important: The optional door input must be connected for

this feature to work.
1-2 Panic On: (1 LED flash) This feature controls whether or not the panic mode
is available with the ignition on. In some states there are laws prohibiting a
horn continually sounding in a moving vehicle. This feature makes the system
compliant with these regulations. The LED flashes twice (2) to indicate Panic with
ignition Off. When Panic is Off, the LED flashes (3)

1-3, Horn Function: Turns On/Off the confirmation honks when locking/unlock-
ing. Use it to change the output pulse duration for vehicles that require a longer
pulse for the horn to honk. Confirmation honks ON (20mS) & panic, (1)
Confirmation honk (30mS) & panic, (2) Confirmation honk (40mS) & panic (3)
Confirmation honk (50mS) & panic (4) Confirmation honks OFF, panic only (5).
When choosing panic only; the horn will not sound when locking or unlocking,
only when the panic feature is used.
1-4 Ignition Locks Off: (1) When turned Off the system does not lock/unlock the
doors when the ignition is turned on. (2) Lock and Unlock. The doors lock three
seconds after the vehicles doors are closed when the ignition is turned On, and
unlock when the ignition is turned Off. (3) Lock: Locks the doors three seconds
after the ignition is turned On and the vehicles doors are closed. 4) Unlock:
Unlocks the doors when the ignition is turned off.
Important: The optional door input must be connected for
the ignition controlled lock feature to work.
1-5 Single Pulse Lock/Unlock(1): The system sends out a single pulse when lock-
ing and unlocking. (2) Double-pulse unlock sends out 2 pulses when unlocking.
(3) Double-pulse lock sends out 2 pulses when locking. (4) Double-pulse lock/
unlock sends out 2 pulses when locking and unlocking.
1-6 0.8 sec Door Lock Pulse (1)Duration:The default setting is 0.8 second door
lock pulses. Some European vehicles, such as Mercedes-Benz and Audi, require
longer lock and unlock pulses to operate the vacuum pump. Programming the
system to provide 3.5 second (2) pulses, accommodates the door lock interface
in these vehicles. (See door lock connections section for wiring information re-
garding Type E door locks interfacing. The 0.4 second (3) pulse is required on
some vehicles where the lock wires can also control the windows and the 0.8
second pulse causes the windows to open/close when locking or unlocking.
1-7 No 2nd Unlock Output (1): The second unlock output is defeated at all
times. 2nd unlock On with ignition control, after first unlock turns on the 2nd un-
lock output and unlocks the passengers doors after the driver’s door is unlocked
with ignition controlled locks. (3) 2nd unlock on with ignition control with first
unlock will turn on the 2nd unlock output and will unlock the passengers doors at
the same time the driver door is unlocked with ignition controlled locks.

1-8 Comfort Closure Off(1): The system can be programmed to close the win-
dows when the system is locked. If programmed ON, the lock output provides a
20 second pulse when the system is locked. The output will be cancelled if the
unlock button is pressed. In the Off setting the system will not do this function.
(2) Comfort closure 1 - Activates the 20 second timer after the door lock pulse.
(3) Comfort Closure 2 - Activates the 20 second timer with the door lock
pulse.
To test if the car has the comfort closure:

1. Insert the key into the drivers door key cylinder.
2. Turn the key to the lock position and hold for about 10 seconds.
If Comfort closure is available, the windows (and in some cars the
sunroof] will close.
Note: Some cars require that you turn the key once, release it, and then turn and
hold into the lock position.
Important: Comfort closure can only be used on cars that
have the capability of closing the windows (and on some cars
the sunroof as well) with the key cylinder in the door.
1-9 Hood Trigger (Normally Open): Hood trigger (normally closed). To pro-
gram the unit for either a normally open (rests open, or at 12v when the hood
is closed) or a normally closed (rests at ground when the hood is closed) pin
switch.
➤ Menu 2 - Convenience
2-1 One time bypass OFF: When programmed Off (1) the unit does not pas-
sively lock for one cycle when turning the ignition On and Off within 3 seconds.
When going through this procedure the horn honks once indicating that One
Time Bypass has been activated. One time bypass On (2), the system passively
locks the vehicle 30 seconds after the ignition is turned off, and the door has
been opened and closed.

2-2 Valet switch pulse count, 1 pulse. Optional starter kill emergency override.
From valet, 2 - 5 pulses. The system can be programmed to count the number of
presses of the valet switch before disabling the optional starter kill. The factory
default setting is one pulse. The unit can also be set for two to five pulses.
2-3 Door trigger error notification: Door trigger error honk Off. When On (1) ,
this feature controls the error honk that is generated if the system is locked with
the door trigger active. This is useful in vehicles with a long dome light delay
after the door is closed. If the system is locked before the dome light turns Off,
the system generates the door trigger error notification. If this error notification
is not desired, use this feature to disable the door open error notification. If the
error notification is turned Off, (2), no bypass horn is generated, even if a door
is accidentally left open.
Important: The optional door input has to be connected for

this feature to work.
2-4 Ignition Controlled Dome Light Supervision On: If turned On (1), the system
turns On the dome light for 60 seconds when the ignition is turned off. The
optional dome light supervision feature must be installed as described in the
Wire Connection Guide. Use the two-honk setting for: Ignition controlled dome
light Off.
2-5 FAD w/trunk release ON: FAD w/trunk release OFF. In the default setting
the factory alarm disarm output will disarm the factory alarm system any time the
button controlling the trunk release output is pressed.
2-6 Factory Alarm Disarm-With Unlock, Before Unlock, Remote Start Only: In
the default setting the factory alarm disarm output will disarm the factory alarm
system any time the button controlling Unlock or Remote Start is pressed. The
“Before Unlock” output will disarm the factory alarm before the unlock output ac-
tivates and when remote start is activated. The “Remote Start Only” will disarm
the factory alarm only when the remote start is activated.
2-7 FAD 1 pulse: FAD 2 pulses. This setting determines how many pulses the
system will output on the Factory alarm disarm wire.

2-8 Aux 1 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. timed
(4)
• Validity: Output that will send a signal as long as the transmission is re-
ceived.
• Latched: Output that will send a signal when the Aux 1 button is pressed
and will continue until the same button) is pressed again.
• Latched, reset with ignition: Similar to the latched output this output type
turns ON the first time the Aux 1 button is pressed and turns OFF the next
the same button is pressed. This output type additionally stops and resets
whenever the ignition is turned ON, and then OFF.
• 30-second timed: Output that will send a continuous signal for 30 sec-
onds.
• Off: Output is disabled.
Note: All auxiliary channel timed outputs can be programmed using the Bit-
writer® (1-90 seconds)
2-9 Aux 1 Linking, None (1) Lock (2) Unlock (3) Lock/Unlock (4) Remote Start
(5). When programming to Validity or timed output this can be programmed to
activate when locking or unlocking (or remote start) with the transmitter.
Note: Aux linking gives you option to have the auxiliary wire activate when
locking, unlocking, locking and unlocking or with remote start.
2-10 Aux 2 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. timed,
(4) Output, (5) Off: Auxl 2 can be programmed for these output configurations.
The unit is set to the default validity output. To change the configuration use the
two-honk setting to toggle through the different configurations. Refer to feature
2-8 for additional details
.
2-11 Aux 2 Linking None (1) Arm (2) Disarm (3) Arm/Disarm (4) Remote Start
(5). Refer to feature 2-9 for additional details.
2-12 Aux 3 Validity (1) Latched (2), Latch reset w/ignition (3), 30 -sec. timed,
(4) Output, (5) Off: Aux 3 can be programmed for these output configurations.
The unit is set to the default validity output. To change the configuration use the
two-honk setting to toggle through the different configurations. Refer to feature
2-8 for additional details.

2-13 Aux 3 Linking None (1) Lock (2) Unlock (3) Lock/Unlock (4) Smart key
control (link to remote start Off. (5). When aux 3 is programmed to Smart Key
control, this wire outputs a 800ms pulse when the Remote Start is shut Off.
The system also monitors the door trigger input. When the door is opened dur-
ing the remote start runtime, the remote start shuts down and this wire outputs
the 800ms pulse.
Important: This wire is connected to the pushbutton wire that start
and stops the car. It pulses the wire at the button to shut off the
car when the remote start is deactivated.
➤ Menu 3 - Remote start

3-1 Manual Transmission Mode: This is the default setting. The two-honk setting
is used for Automatic transmission mode. In the default setting the remote start
unit is programmed to look for a shutdown procedure to activate the remote
start.
Important: The optional door input has to be connected for
manual transmission start to work.
3-2 Engine Checking Virtual Tach: (1) When set to “virtual tach” (1) the remote
start monitors the cranking voltage of the vehicle and sets it as a reference point.
Fifteen seconds after the crank output sequence the remote start checks the volt-
age again to determine if the vehicle is running.
When set to voltage, (2) the unit cranks the starter for the programmed time and
then attempts to sense that the engine is running by detecting an increase in volt-
age. If programmed Off (3) the vehicle cranks for the programmed crank time.
The tach setting or voltage setting is not checked to verify that the car is running.
In the OFF setting, if the vehicle fails to start, the ignition stays on for the run dura-
tion. Using tach or either of the voltage settings is recommended.
When set to Tachometer, (4) the unit references the learned tach signal to disen-
gage the starter. In addition it will monitor the RPM and shut down if the engine
RPM is too high or too low.
Important: The tach wire must be connected and
programmed for the manual transmission mode to work.

3-3 Crank Time 0.6 0.8 (2) 1.0 (3) 1.2 (4) 1.4 (5) 1.6 (6) 1.8 (7) 2.0 (8)
4.0 (9) SECONDS: If the unit is programmed for no engine checking or voltage
sense, the crank time must be set to the appropriate duration. The default setting
is 0.6 second and the LED will flash once. If a different crank time is desired,
toggle through the higher settings by using the two-honk settings.
3-4 Run Time 12 (1), 24 (2) 60 (3) MINUTES: Selects the time in minutes
that the system will operate the engine until the system “times out”. The system
may be shut down using the remote or any of the shutdowns at any time. Using
the Bitwriter®, the run time can be programmed for any duration from 1-60
minutes.
3-5 Activation Pulse One: This allows the system to use 1 or 2 pulses to activate
the remote start sequence. The default setting is 1-pulse.
Note: This setting affects both the input wire and the remote control.
3-6 Turbo Mode: The factory default is OFF (1). On1 min (2), On 3 min (3) On
5 min (4) On 10 min (5): In the Off setting the turbo mode does not function. In
the On and timed setting, the remote start can be used as a turbo timer. The car
remains running for the programmed runtime, and the ignition is turned Off.
3-7 Timer Mode Run Time—12min (1): This is the default setting. Selects
the time in minutes that the system will operate the engine until the system “times
out” when the remote start activates in timer mode. Use the two-honk setting for
3(2), 6 (3), 9 (4) MINUTES: This is the maximum operation period and the
system may be shut down using a shutdown at any time. Using the Bitwriter®,
the run time can be programmed for any duration from 1-16 minutes.
3-8 Flex Relay Function: Ignition 2 (1) In the factory setting, the flex relay will
function the same as the pink ignition 1 wire, in accessory setting the flex relay
will function the same as the Orange accessory 1 wire, in starter setting the flex
relay will function the same as the purple starter 1 wire.
3-9 Diesel Timer—Wait-To-Start Input - Timed 15, 30, 45 SECONDS:

Default is the “Wait-to-Start” input control wire, or programmable to ignore the
input control wire by a delay of 15 (2), 30 (3), or 45(4) seconds. This feature
can also be optionally programmed with the Bitwriter®, with a delay from 1 to
90 seconds.

3-10 Accessory State During Wait-To-Start On: This feature will allow the se-
lection of the accessory output to be ON or OFF during wait-to-start. Use the
two-honk setting for OFF.
3-11 2nd Status Output: Normal: This feature will allow selection of status
output or a rear defogger mode that turns on ten seconds after the vehicle has
started if the vehicle interior temperature is below 55 degrees F. The defogger
mode has two selections, latched, the LED will flash twice, or pulsed, the LED will
flash three times. Latched mode will only stay on for 10 minutes.
Note: When the defogger mode is on, the output will always be active and can
be turned on independently with the remote for a one-time activation. (See the
Remote control configuration table.)
3-12 Parking Lights Constant: In the default setting, the parking lights (if con-
nected) will come on solid during the remote start runtime. In the two- flash setting
the parking lights will flash during the remote start runtime. In the OFF setting, the
parking lights will not come ON or flash, when the vehicle is remote started.
3-13 Anti-Grind On: With the anti-grind On (default) the ground-when-armed

output will be active during remote start operation. This activates the optional
starter kill relay and prevents the customer from re-cranking the car with the key,
when doing key takeover. If accessories such as a voice module or window
module are added to the unit, it may be necessary to use the two-honk setting
to program this feature OFF.
3-14 Tach Mode Starter Release: Normal: Use the two-honk setting to in-
crease time by 15% of the original tach programmed time. The LED will flash
twice (2). To decrease by 15% of the original programmed time, the LED will
flash three (3) times.
3-15 Vehicle temperature auto report ON or OFF*. The default setting is OFF.
When programmed ON the main unit will store the interior temperature of the
vehicle in its temporary memory. When the vehicle’s interior temperature chang-
es 1 degree Celsius, the main unit automatically sends the interior temperature
message to the remote and the LED’s light up accordingly to display the current
temperature.
*with 2-way upgrade
➤ Bitwriter®
The Bitwriter® has the ability to fine tune certain features of the system.
These features and the adjustments that may be programmed are described in
the table that follows.
Note: Feature programming for Responder LC remote controls with a display

screen are available when using the Bitwriter, however these features do not
apply to this system.
Feature Default Optional settings

setting
Aux/ trunk icon type Trunk Window, sunroof, audio, lights, left slider
dr, right slider dr, rear hatch.
Aux 1 timed output 30 seconds 1-90 seconds
Diesel start timer 15 seconds 1-90 seconds
Timer mode run time 12 minutes 1-16 minutes
Timer mode starts 6 starts 1/2/3/4/6/8/10/12/14/16/
1820/22/24 (Starts)
Timer mode intervals 3 hours 1/2/3/4/6/8/10/12/14/16/
18/20/22/24 (Hours)
Smart start low temp 0 (F) OFF/-20/-10/0/10/20/30/40/50

/60/70 (F)
Smart start high temp 100 (F) OFF/40/50/60/70/80/90/100/

110/120/130 (F)
Smart start low battery 10.5 volts OFF/12.5/12/11.5/11/10.5/10/
9.5/9 volts
Tach mode starter 10 (normal) 0/1/2/3/4/5/6/7/8/9/10/11/1
release 2/13/14/15/16/17/18/19/20
Virtual tach fine tune Not initialized 0 - 1 second in 50mS increments

Feature Default Optional settings
setting
Feature programming Unlocked Locked
Transmitter programming Unlocked Locked
Remote start runtime 12 minutes 1-60 minutes

Shutdown diagnostics
To perform shutdown diagnostics:
1. With the ignition OFF, press and hold the Valet/Program switch.
2. Turn the ignition ON and then back OFF while holding the Valet/Pro-
gram switch.
3. Release the Valet/Program switch.
4. Press and release the Valet/Program switch. The LED flashes a number of
times on the control center to report the last shutdown for one minute or
until the ignition is turned on, as shown in the following table:
LED Flashes Shutdown Mode

1 Runtime expired
2 Over-rev shutdown
3 Low or no RPM
4 Transmitter shutdown (or optional push button)
5 (+) Brake shutdown
6 (-) Hood shutdown
7 Timer mode/Turbo mode/Manual mode error *
8 Neutral safety shutdown
9 Low battery (voltage mode)
10 -------------------------------------------------------
11 Wait-to-start input timed out
* Timer mode error: Ignition is on or shutdown input is active when activating
timer mode.
Turbo mode error: Turbo mode is programmed off, engine is not on or
shutdown input is active.
Manual mode error: MTS not enabled.

Remote starting diagnostics
When the remote start function is activated, you can determine the cause of
the no-start situation by counting the number of parking light flashes from the
vehicle.
Parking Light
Flashes
5 Brake wire is active

6 Hoodpin wire is active
7 Manual transmission mode is enabled and not
initialized.
8 Neutral safety wire has no ground or the neutral safety
switch is Off.

Remote start safety check
Before vehicle reassembly, the remote start system must be checked to ensure safe
and trouble-free operation. The following test procedure must be used to verify
proper installation and operation of the system. The installation must be com-
pleted before testing, including connection to the brake switch and hood switch.
1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the
remote start system. Once the engine is running, press the brake pedal.
The engine should shut down immediately. If the engine continues to run,
check the brake circuit connection.
2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the
hood. Activate the remote start system. The vehicle should not start. If the
starter engages, check your hood pin and connections.
3. Test the NEUTRAL SAFETY shutdown circuit.
Important: Make sure there is adequate clearance to the
front and rear of the vehicle before attempting this test.
4. Make sure the hood is closed and no other shutdown circuits are active.
5. Set the emergency brake.
6. Turn the ignition key to run position but do not start the engine.
7. Put the vehicle in Drive (D).
8. Put your foot over the brake pedal but do not press down on it. Be ready
to step on the brake to shutdown the remote start system.
9. Activate the remote start system.
• If the starter engages, immediately step on the brake to shut down the
system. If it does engage, recheck the neutral safety input connection. The
vehicle may use a mechanical neutral safety switch. (See H3/1 BLACK/
WHITE neutral safety switch input in Remote Start Harness Wire Connec-
tion Guide section of this guide.)
• If the starter does not engage, the test is complete. Once the system passes
the tests, the vehicle can be re-assembled and delivered. Do not the use
the remote start system or finalize the installation if it fails any of the safety
check tests.

Troubleshooting
➤ Keyless entry system
• System will not passively lock until it is remotely locked and then un-
locked:
Are the door inputs connected? Is the H1/6 blue wire connected to the door
trigger wire in the vehicle? Either the H1/5 green or the H1/7 violet should be
used instead. (See wiring diagrams.)
• The Valet/Program switch doesn’t work.

Is it plugged into the correct socket? See Plug-In LED and Valet/Program Switch
section of this guide.
• Status LED doesn’t work.

Is it plugged in? (See Plug-In LED and Valet/Program Switch section of this
guide.) Is the LED plugged into the correct socket?
• Door locks operate backwards.

This unit has easily-reversed lock/unlock outputs. Recheck wire connections to
see if you have reversed these.
➤ Remote start
• The remote start will not activate
1. Check remote startup diagnostics to determine what may be the cause of
the no start situation.
2. Check the harnesses and their connections. Make sure that the harnesses
are completely plugged into the remote start module. Make sure there are
good connections to the vehicle wiring.
3. Check voltage and fuses on the main 12-pin harness and on the heavy
gauge remote start harness.

• The remote start will activate, but the starter never engages.
1. Check for voltage on the purple starter wire two seconds after the remote
start becomes active. If there is voltage present, skip to Step 4. If there is
not voltage present, advance to Step 2.
2. Check the 30A fuses.
3. If the gray/black wait-to-start wire is detecting ground upon activation, the
starter will not crank.
4. Make sure the purple starter wire is connected on the starter side of the
optional starter kill/anti-grind relay.
5. Does the vehicle have an immobilizer? Some immobilizer systems will not
allow the vehicle to crank if active.
6. Check connections. The heavy gauge remote start input wires on the
heavy gauge 10-pin connector should have a solid connection. “T-taps”
or “scotch locks” are not recommended for any high current heavy gauge
wiring.
• The vehicle starts, but immediately dies.

1. Does the vehicle have an immobilizer? The vehicle’s immobilizer will cut
the fuel and/or spark during unauthorized starting attempts.
2. Is the remote start programmed for virtual tach voltage sense? If so, the
crank time may not be set high enough. Voltage sense will not work on
some vehicles.
3. Check diagnostics. Sometimes a shutdown will become active during
cranking or just after cranking.
• The vehicle starts, but the starter keeps running.

1. Is the system programmed for engine checking off or virtual tach voltage
sense? When programmed for either of these features, the engine cranks
for the pre programmed crank time regardless of how long it takes for the
vehicle to actually start. Adjust to a lower cranking time.
2. Was the Tach Learn successful? The LED must light solid and bright to
indicate a successful learn.
3. Make sure that there is a tach signal at the purple/white tach input wire
of the remote start. If there is not a tach signal, recheck the connection to
the vehicle’s tach wire and make sure the wire is not broken or shorted to
ground leading to the remote start.

• The vehicle starts, but will only run for 10 seconds.
1. Is the remote start programmed for voltage sense? If this does not work, a
tach wire should be used.
2. Check shutdown diagnostics.
• The climate control system does not work while the unit is operating the
vehicle.
Either the wrong accessory wire is being energized or more than one igni-
tion or accessory wire must be energized in order to operate the climate
control system.
• Manual Transmission Start diagnostics

When enabling MTS, if you get a failure notification from the remote or
the vehicle fails to remain started when you shut off the key, check for
following:
• Hood Open (gray wire)
• Foot Brake active (brown wire)
• No Parking Brake input-Black/white neutral safety wire not showing
ground with parking brake set.
• Tach not hooked up or programmed
• Toggle switch not installed or not in the ON position.
N4102V 2008-09
Vista, CA 92081
www.directed.com
© 2008 Directed Electronics—All rights reserved

Installation Viper 5101

Uploaded by

Copyright:

Available Formats

Installation Viper 5101

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation Viper 5101

Uploaded by

Copyright:

Available Formats

Remote Start Keyless Entry

This product is intended for installation by a professional

© 2008 Directed Electronics, Vista, CA

The Bitwriter® (p/n 998U)

Bitwriters with date code of 6A or older require an IC upgrade

© 2008 Directed Electronics. All rights reserved. 5

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

6 © 2008 Directed Electronics. All rights reserved.

Installation points to remember

The “Automatic” option should be programmed on to work with automatic trans-

© 2008 Directed Electronics. All rights reserved. 7

➤ The control center

➤ Valet® program switch

8 © 2008 Directed Electronics. All rights reserved.

➤ After the installation

© 2008 Directed Electronics. All rights reserved. 9

Making your wiring connections

10 © 2008 Directed Electronics. All rights reserved.

**Not available with 1- way remote

➤ Auxiliary harness (H2), 7-pin connector

© 2008 Directed Electronics. All rights reserved. 11

➤ Heavy gauge remote start, (H3) 8-pin connector

➤ Remote start input, 5-pin connector

12 © 2008 Directed Electronics. All rights reserved.

➤ Door lock harness, 3-pin connector

© 2008 Directed Electronics. All rights reserved. 13

Warning! Never use this wire to drive anything but

H1/2 RED (+)12v CONSTANT INPUT

14 © 2008 Directed Electronics. All rights reserved.

Light Flash Fuse

© 2008 Directed Electronics. All rights reserved. 15

H1/6 VIOLET (+) DOOR TRIGGER INPUT*

16 © 2008 Directed Electronics. All rights reserved.

(-) GROUND (-) GROUND

(+)HORN CIRCUIT IN VEHICLE H1/7 BLUE

*This feature is only available with a 2-way remote upgrade.

H1/8 GREEN (-) DOOR TRIGGER INPUT*

H1/10 WHITE/BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT

Note: The number of activation inputs can be programmed to 1 or 2 pulses with

18 © 2008 Directed Electronics. All rights reserved.

(+) Positive Light Flash Output

(-) Negative Light Flash Output

H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT

© 2008 Directed Electronics. All rights reserved. 19

Relay for Negative (-) Relay for Positive (+)

H2/2 LIGHT GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT

20 © 2008 Directed Electronics. All rights reserved.

Warning! Never use this wire to drive anything

H2/4 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT

Warning! Never use this wire to drive anything

H2/5 WHITE/BLACK (-) 200mA AUX 3 OUTPUT

This wire provides 200 mA programmable output whenever the transmitter

• Validity: Output that sends a signal as long as the transmission is re-

© 2008 Directed Electronics. All rights reserved. 21

Note: Bitwriter® programs from 1 to 90 seconds.

Warning! Never use this wire to drive anything

H2/6 LIGHT BLUE (-) 200mA 2ND UNLOCK OUTPUT

H2/7 GRAY/BLACK (-) DIESEL WAIT TO START INPUT

22 © 2008 Directed Electronics. All rights reserved.

© 2008 Directed Electronics. All rights reserved. 23