EASA Module 11 : Aeroplane

Aerodynamics Structure & Systems

Question
EASA Module 11 : Aeroplane Aerodynamics Structure
& Systems Question-Answer

How many axis does the aircraft autopilot control?

a) Two
b) Three
c) Four
Ans :b

A diode connected across a coil will

a) prevent back EMF and allow faster switching
b) suppress arching when relay is opening and closing
c) prevent the coil being fitted the wrong way
Ans :b

Which fault does not trip the GCR?

a) Under frequency and under volts
b) Over frequency and over volts
c) Over frequency and under frequency
Ans :c

Differential protection in a generating system

a) detects voltage difference between source and load
b) detects current difference between source and load
c) uses the volts coil to trip the GCR
Ans :b
Open phase sensing on a current transformer
a) is detected using all phases
b) is detected using any phase
c) is detected on generator neutral circuit
Ans :c

Emergency floor lighting system is inoperative, then

a) the aircraft is allowed to fly empty to a main base
b) the aircraft is not allowed to fly until repaired
c) the aircraft is allowed to fly in daylight conditions only
Ans :a

A white light must be

a) of five candela showing from starboard side through an angle of 110 degrees in
the horizontal plain
b) of at least 3 candela showing through an angle of 110 degrees from dead astern
in the horizontal plain
c) of at least 3 candela showing through 70 degrees from dead astern to each side in
the horizontal plain
Ans :c

If battery is switched off in flight the

a) battery is disconnected from bus
b) generator voltage falls to zero
c) captain's instruments will be powered from the standby bus
Ans :a

To flash a generator field

a) generator must be stationary
b) rotate but not on line
c) on line and producing a voltage less than the flashing voltage
Ans :a

A hydraulic motor generator's voltage and current is controlled by

a) the swash plate
b) the constant speed drive
c) the voltage regulator
Ans :c

The ground interlock pins are numbered

a) A and B
b) C and N
c) E and F
Ans :c

A nose down change of trim (tuck under) occurs due to shock induced on
a) tip stall on a straight wing aircraft
b) tip stall on a delta wing aircraft
c) root stall on a delta wing aircraft
Ans :c

Zone 320 under the ATA system is

a) vertical stabiliser
b) central fuselage
c) horizontal stabiliser
Ans :a

When doing a bonding check the maximum resistance between component and
earth is
a) 0.005ohms
b) 1/50 ohms
c) 50 milliohms
Ans :c

Which instrument are most likely to damage if you have a rapid drop in pressure,
when carrying out a pilot static leak check?
a) Altimeter
b) Air speed indicator
c) vertical speed indicator
Ans :a

The aeroplane fin is of symmetrical aerofoil section and will therefore provide a side-
load
a) only when the rudder is moved
b) if a suitable angle of attack develops due either yaw or rudder movement
c) only if a suitable angle of attack develops due to yaw
Ans :b

An aircraft left wing is flying low. The aileron trimmer control to the left aileron trim
tab in the cockpit would be
a) moved up causing the left aileron to move down
b) moved up causing the left aileron to move up
c) moved down causing the left aileron to move down
Ans :a

The bearing used in a fibre pulley is

a) a roller bearing
b) a plain bearing
c) a ball bearing
Ans :c

The real time on a CMC is when

a) existing faults page is selected on the CDU
b) ground test page is selected on the CDU
c) fault history page is selected on the CDU
Ans :a

The signal line between the controller and discharge valve is leaking. This will cause
a) the cabin pressure to decrease
b) the cabin pressure to increase
c) it will not effect on cabin pressure
Ans :b

A spill valve opens

a) to control the air from the cabin to outside
b) to control the flow to the cabin
c) to prevent an excessive pressure difference
Ans :b

An aircraft aerofoil is exposed to supersonic flow. The boundary layer

a) is subsonic
b) increases in depth
c) is supersonic
Ans :a

A brake debooster valve is provided for

a) decreasing the pressure and slowly releasing the brakes
b) applying brake pressure slowly and releasing the the brakes quickly
c) increasing the pressure and applying the brakes rapidly
Ans :

A symmetrical aerofoil is accelerating through Mach 1 with an angle of attack of 0°. A

shock wave will form
a) on the upper surface only and move aft
b) on the upper and lower surface and will move aft until the point of maximum
camber
c) on the upper and lower surface and will move aft
Ans :c

One of the inputs in a CMC is autopilot controls. The data will be stored in
a) volatile memory
b) non-volatile memory
c) erased only after end of sector
Ans :b

The runway heading is

a) QDH
b) QDR
c) QDM
Ans :c

A spar web will take loads in

a) shear
b) tension
c) bending
Ans :a

What kind of seal are used on firewall bulkheads?

a) soft rubber
b) fire-proof grommets
c) None required
Ans :b
A fuel cross-feed valve is powered from
a) AC busbar
b) the battery
c) DC busbar
Ans :c

A fuel cross-feed valve is lubricated

a) by the fuel
b) by internal cooling
c) by air
Ans :a

A cabin altitude is protected against reaching an altitude of 13000 ft by

a) bellows in the outflow valve
b) altitude sensor
c) cabin over pressure relief valve
Ans :b
How is damage to the nose cone of an aircraft prevented during a lightning strike?
a) Bonded Strip
b) Earthing Strap
c) Special paint
Ans :a

ILS marker beacon lights are

a) green, blue, amber
b) blue, amber, white
c) blue, white, green
Ans :b

111.1 MHz is
a) an ILS frequency
b) a VOR frequency
c) a HF frequency
Ans :a

An autopilot PFCU servo brake is

a) energised on
b) energised off
c) energised at the same time as the clutch
Ans :b

A fluorescent tube contains

a) orange coatings, rare gases and mercury vapour
b) phosphor coatings, rare gases and mercury vapour
c) iodine coatings and rare gases
Ans :b

Distilled water should be added to a ni-cad battery

a) when fully charged
b) at any time
c) only in the battery workshop
Ans :a

Overflowing electrolyte in a ni-cad battery indicates

a) excessive charging current
b) not enough charging current
c) low electrolyte temperature
Ans :a

The aviation distress frequency is

a) 122.5MHz
b) 121.5MHz
c) 121.5kHZ
Ans :b

A radar altimeter in track mode is effective to

a) 2000 ft
b) 100 ft
c) 2500 ft
Ans :c

During a normal engine shutdown, generator tripping is initiated by

a) undervoltage
b) underfrequency
c) overcurrent
Ans :a

112.1 MHz is
a) an ILS frequency
b) a VOR frequency
c) an ADF frequency
Ans :b

What does a Decca Navigation system operate on?

a) Low Frequency
b) High Frequency
c) Very High Frequency
Ans :a

What is the minimum separation between a seat back cushion and another seat or
fixed structure?
a) 24 inches
b) 26 inches
c) 28 inches
Ans :b

In an autoland aircraft fitted with a CMC

a) all faults are recorded in Volatile memory
b) all faults are recorded in Non-Volatile memory
c) only Primary Faults are recorded
Ans :b

Adhesive Bonding is
a) wetting + gripping
b) wetting + Setting
c) spread + setting
Ans :b

Tension is the stress of

a) twisting
b) elongating or stretch
c) crush or compression
Ans :b

What are the minimum number of fire bottles in a cabin with 201- 300 people?
a) 3 BCF
b) 4 Methyl Bromide
c) 4 Fire Extinguishers
Ans :c

On an aircraft with asymmetrical ailerons what happens to induced drag when

banking right?
a) Drag on inside aileron goes up but not as much as the outer
b) Drag on the outer aileron increases
c) Drag on the outer aileron is less
Ans :c

When the primary stops fitted to a control run have been contacted
a) a clearance exists at the secondary stops
b) the secondary stops will just be in contact
c) the secondary stops have been over-ridden
Ans :a
Excessive wear on both sides of the control cable pulley groove is evidence of
a) pulley misalignment
b) cable misalignment
c) excessive cable tension

Ans :a

Auto pilot servo brake is energised

a) to actuate off
b) at the same time as the clutch
c) to actuate on
Ans :a

Hand held mikes are not permissible on

a) public transport aircraft
b) public transport or aerial work
c) private aircraft only
Ans :a

Track altitude in a radio altimeter system begins at

a) 10 000ft radio alt.
b) 2 500ft radio alt.
c) 1 000ft radio alt.
Ans :b

A fuel crossfeed valve is usually in

a) the open position
b) the closed position
c) its last position
Ans :b

Full time yaw damper system detects

a) only low frequencies
b) all frequencies
c) band pass frequencies
Ans :c

What is the radio altimeter track altitude?

a) 500ft
b) 2500ft
c) 10000ft
Ans :b

Which category are hand mikes considered essential?

a) Light aircraft
b) Aerial work aircraft
c) Heavy passenger aircraft
Ans :a

Emergency frequency is
a) 121.5
b) 123.5
c) 125.5
Ans :a

Sliding couplings in fuel systems are used on

a) high pressure systems
b) low pressure systems
c) air or vapour systems
Ans :c

Cargo and baggage compartments in which a fire is completely confined come under
a) Class B
b) Class C
c) Class D
Ans :c

When a current transformer is disconnected what should be done?

a) Terminals shorted
b) Resistor placed across terminals
c) Left open circuit
Ans :a

What does the differential sensing coil sense?

a) Current
b) Volts
c) Power
Ans :a

121.5 Mhz is what frequency?

a) VHF
b) ILS
c) VOR
Ans :a

112.1 Mhz is what frequency?

a) VOR
b) ILS
c) VHF
Ans :a

Where does the GCU gets its power?

a) PMG
b) Battery
c) RAT
Ans :a

Galley loads are wired in

a) series
b) parallel so load shedding will lower current consumption
c) either series or parallel depending on the design
Ans :b

On a fibreglass aerial, what paint should be used?

a) Cellulose only
b) Not cellulose
c) Polyurethane
Ans :b

A current limiter
a) limits current flow to a load
b) opens a circuit after a time/current condition has been exceeded
c) can be used as a radio suppressor
Ans :b

When a load is shed from a busbar the

a) busbar voltage increases
b) current consumption from the bar decreases
c) busbar voltage decreases
Ans :b

In unparalleled AC generation systems the phase rotation of one generator in

relation to the others
a) is unimportant
b) must be synchronised prior to paralleling
c) must be BCA
Ans :a

In a multi-generator system, the generator which takes more than its reactive power
share is protected by
a) overcurrent and under current protection circuits
b) over voltage and under voltage protection circuits
c) over excitation and under excitation protection circuits
Ans :b

Sharing of electrical loads by paralleled DC generators is controlled by

a) equalising circuits which control the speed of the generators
b) equalising circuits which control the field excitation of the generators
c) automatic load shedding
Ans :b

Excessive commutator sparking can be caused by

a) brushes positioned on MNA
b) weak spring tension
c) rotating field diode failure
Ans :b

Before checking the SG of a battery recently removed from an aircraft

a) allow to stabilise for one hour
b) take the temperature of the electrolyte
c) carry out a capacity test
Ans :a

When painting a neoprene coated radio antenna

a) use cellulose paint
b) use any paint
c) do not use cellulose paint
Ans :c

On an AC external power plug, the interlock circuit is controlled by pins

a) AB
b) CD
c) EF
Ans :c
Over voltage protection circuits are activated
a) before the over voltage limit is exceeded
b) dependent on the magnitude of the overvoltage
c) after a fixed time delay
Ans :b

With respect to flight spoilers they

a) only operate on the ground
b) only operate in flight
c) can operate both on the ground and in flight
Ans :c

Aircraft emergency escape slides are usually pressurised with

a) oxygen
b) CO2
c) helium
Ans :b

As an aircraft descends from cruising altitude (34,000ft), the cabin altitude must
a) stay the same
b) increase
c) decrease
Ans :c

A refrigerant is used in which of the following?

a) Air cycle machine
b) Pneumatic pump
c) Vapour cycle
Ans :c

With aircraft lights - which of the following is true?

a) Starboard light red, port light green, tail light Red
b) Starboard light red, port light green, tail light White
c) Starboard light green, port light red, tail light white
Ans :c

An ECAM system is tested under the following conditions:-

a) Aircraft on the ground with one engine running
b) Aircraft on the ground with parking brake set/on
c) Aircraft in the air with both engines running
Ans :b

With respect Differential Aileron Control, which of the following is true?

a) The up going Aileron moves through a smaller angle than the down going aileron
b) The up going and down going ailerons both deflect to the same angle
c) The down going aileron moves through a smaller angle than the up going aileron
Ans :c

A lead-acid battery is considered to be fully charged when the

a) SG reaches 1.180
b) cells begin to gas freely
c) SG and voltage remain constant for specified period
Ans :c

The preferred method of battery charging a Ni-Cad battery is constant

a) voltage
b) current
c) power
Ans :b

Wing spoilers, when used asymmetrically, are associated with

a) elevators
b) rudder
c) ailerons
Ans :c
In an aircraft flying control system employing servo-tabs, the installation of external
ground locks to the main control surface
a) is unnecessary since the system is irreversible and therefore the control surface
cannot be displaced by the wind
b) would not prevent movement of the control column
c) would also prevent movement of the control column
Ans :b

Air above Mach 0.7 is

a) compressible
b) incompressible
c) compressible only when above the speed of sound
Ans :a

Supersonic air passing through a divergent duct causes the

a) pressure to increase, velocity to increase
b) pressure to decrease, velocity to increase
c) pressure to increase, velocity to decrease
Ans :b

An aircraft flying below the tropopause descends at a constant True Airspeed, its
Mach. No. will
a) increase
b) decrease
c) not change
Ans :b

Spongy brakes are usually a result of

a) air in the system
b) internal leakage
c) external leakage
Ans :a

Over inflated tyres may cause damage to the

a) wheel hub
b) wheel flange
c) brake drum
Ans :b

Blowout panels are fitted to floors of pressurised aircraft to

a) provide access for pressurising the aircraft
b) relieve pressure if the maximum differential is exceeded
c) provide venting should a differential pressure build up across the floor
Ans :c

If an aircraft is yawing to the left, where would you position the trim tab on the
rudder?
a) To the left
b) To the right
c) To the centre
Ans :a

If an aircraft is flying with a left wing low, where would you move the left aileron trim
tab?
a) Up
b) Down
c) Moving the aileron trim tab will not correct the situation
Ans :a

When a Leading edge flap is fully extended, what is the slot in the wing for?
a) To increase the lift
b) To re-energise the boundary layer
c) To allow the flap to retract into it when it retracts
Ans :b

A purpose of a cut-out in a hydraulic system

a) is to limit loss of fluid in the event of pipe fracture
b) is to prevent creep in jack operated services which have several selected
positions
c) is to relieve the pump of load when the operation of services is complete and the
accumulator charged with fluid
Ans :c

Hydraulic pressure can be restored by

a) the use of a pressure/heat exchanger
b) compressing the air charge in an accumulator
c) compressing the fluid in a reservoir
Ans :b

A universal protractor used to measure degrees of aileron travel should be zeroed

a) with the aileron in the neutral position
b) with the aileron in the down position
c) when the aircraft is in level flight attitude

A flying control static friction check

a) can only be carried out during flight
b) will demonstrate that a high force is always necessary to operate non-powered
controls.
c) demonstrates the force the pilot requires to overcome system inertia and move the
controls

Anoxia is due to
a) release of nitrogen bubbles in the blood
b) lack of oxygen
c) low air pressure on the body

The basic system of cabin pressurisation is to arrange a constant

a) inlet and outlet
b) outlet and vary the inlet
c) inlet and vary the outlet

The purpose of the differential capsule in a pressure controller is to control

 a) the rate of pressurisation
b) cabin differential pressure
c) cabin air flow

Control of rate of change of cabin pressure is

a) more important in descent
b) equally important in ascent and descent
c) more important in ascent

With a pressurised aircraft at max differential pressure and a cabin pressure

increase occurs, the differential capsule in the pressure controller will
a) have a constant mass flow
b) let all pressurising air to be spilled over board
c) let pressurisation to be switched off until leaks cause a drop in pressure

If the cabin altitude increases above the normal maximum

a) a warning light comes on in the cockpit
b) compressor delivery is automatically boosted
c) an inward relief valve opens

Fuel cross feed valves are lubricated by

a) fuel
b) special lubricant
c) no lubrication needed

Fuel cross feed valves are operated by

a) 28 v dc bus
b) battery dc
c) 115 v ac

Part - 2

1. Static margin is the distance between

a) aerodynamic center & neutral point
b) aerodynamic center & center of gravity
c) center of pressure & center of gravity
d) neutral point and center of gravity

2. During nidder maintenance

a) chord line should be parallel to horizontal
b) hose over condition is called over balance
c) hose down condition is called over balance
d) as in a & c

3. Loft does not depend on

a) aerofoil design
b) amount of using dehedral
c) density of air & velocity
d) wing surface area

4. Which of the following should also be checked in addition to hard landing

inspection items, when the a/c makes hard landing
a) wing center section
b) arcing of propeller
c) balancing of control surfaces
d) none

5. Artificial feel is used in

a) aileron control system
b) elevator control system
c) rudder system
d) all

6. Which of the following takes the structural loads in the wheel bay?
a) keel beam
b) transverse beam
c) box beam
d) all

7. Structural fuse
a) prevents primary structure damage
b) previcts shear loads
c) prevents overflow of current in the circuit
d) as in a & c

8. Color coding of ‘O’ rings indicates

a) age
b) temp
c) vapour compatibility
d) all

9. The angle of attack where lift/drag ratio is maximum is called

a) ditedral
b) anhedral
c) incidence
d) washin

10. Mark the correct statement

a) stall speed with c.g forward movement
b) stall speed with backward movement
c) stall speed does not change with c.g movement

11. Station 185 indicates

a) 183 mm back of the nose or reference datum
b) 183 inch back of the reference datum
c) 183 cm back of the nose or reference datum
d) 18.30 inch back of the nose or reference datum

12. ‘Out of freezer’ life is associated with

a) epoxy resin
b) catalyst
c) prepeg
d) thermosetting

13. Amount of roll dies not depend on

a) Angle of pitch
b) Angle of bank
c) Angle of turn
d) As in a & c

14. Damage of rivets around the head is usually

a) grey
b) white
c) brown
d) as in a & c

15. The a/c is about to land, the fowler flap is extended, it will cause:
a) in lift
b) in drag
c) lift with nose drag movement
d) normal

16. When the temperature is more than standard value, the TAS will be
a) higher
b) lower
c) first & then remains with effected
d) remains inaffected

17. Strain is measured by

a) original length divided by change in length
b) force by area
c) pressure multiplied with change in length
d) unit distortion of body

18. How selection provides

a) 250v AC
b) 218 v AC & 121v respectively
c) 218v, 400 Hz AC
d) none

19. Adverse load distribution requires

a) gross weight inspection
b) aft adverse loading check
c) forward adverse loading check
d) all the above

20. Which pressurization system component prevents cabin altitude being more than
the a/c altitude
a) safety relief valve
b) negative pressure relief valve
c) compressor inlet sentor

21. A solid metallic sound in coin tap test of honeycomb structure indicates:
a) core damage
b) facing damage
c) facing & core damage
d) separation of layers in honeycomb constructions

22. Smoke clearance system is used with

a) pneumatic systems
b) fire protection system
c) as in b and a pre-set temperature

23. Emergency exit devices located/associated with

a) cabin entry doors
b) passenger entry doors
c) cargo entrance

24. To avoid tip stalling & making the aileron effective for complete flight, wing is
provided with was out, wash out means
a) incidence is angle is greater at wing tip than wing root
b) incidence angle is greater at wing root than wing tip
c) wing tip is a located ahead when componed to wing root

25. Under inflation is indicated by

a) shoulder wear out in the tyre
b) more tread wear
c) high brake heat

26. Tail skid prevents

a) tail section damage
b) rotation of a/c
c) as in a & c

27. Static discharge damage is identified by

a) pits on the surface
b) wing tips & trailing edges are damaged
c) round holes on the surface
d) usually found at wing tips, trailing edges & antennas

28. When proper jigs are not available, the smoothness of center of the a/c wing is
measured by
a) applying Vaseline & cellulose paper
b) using a thin cord along the leading edge to trailing edge parallel to the line of flight
c) veins a thin cord long the lending edge to trailing edge parallel to the lateral axis
d) both a & b

29. Boundary layer thickness is minimum where

a) airflow gets zero to max velocity change
b) airflow velocity is maximum
c) –
d) –

30. At high altitudes, presence of foam in hydraulic fluid is caused by

a) defective pressurization system
b) no hydraulic fluid in the system
c) low pr in the system

31. Purpose of surge tank is

a) it protects tank structure damage
b) it allows fuel to flow into the tank which is at a laterally lower level
c) it collects over flowing fuel
d) as in b & c

32. With in airspeed

a) induced drag more than parasite drag
b) parasite drag more than induced drag
c) induced & parasite drag will be same
d) induced & parasite drag will not be affected

33. Surface hardness of steel

a) with of carbon content
b) only upto a certain point with of carbon content
c) max for wrought iron
d) depends on the process involved

34. Parts which are cold worked should not be

a) welded
b) kept in room with high our temp
c) kept in air conditioned room
d) –

35. Corrosion on spot welding seam is detected by

a) X-ray
b) Ultrasonic
c) Straight edge
d) Point peeling off

36. Mark the correct statement

a) spoilers are used with ailerons for lateral stability about longitudinal axis
b) flaps & spoilers are auxiliary control surfaces used for lateral stability
c) –
d) all the above

37. Contamination of hydraulic fluid is found by

a) viscosity
b) flash point
c) moisture content
d) all the above

38. Mark the correct statement

a) damage of nose cone does not affect flt of an a/c
b) damage to secondary structure like wing tip & nose cone does not affect the flt of a/c
c) damage to seat & seat supporting structure affect flight
d) none of the above

39. Mark the correct statement regarding reynold’s number

a) if the Rey’s no is high then kinematic velocity is high
b) higher the Rey’s No., higher the kinematic viscosity
c) higher the Rey’s No, smaller the kinematic viscosity
d) higher the Rey’s No. smaller the kinematic viscosity & velocity

40. Vortex generators are aerofoils installed on wing upper surface because
a) laminar flow is more difficult to separate than turbulent flow
b) turbulent flow is more difficult to separate than laminar flow
c) –
d) –

41. Balance panels are operated

a) hydraulically
b) manually
c) only in turbulent weather
d) to balance the ailesins

42. Mark the correct statement

a) steel & magnesium is used for secondary structural members
b) fiberglass & magnesium is used for secondary structural members
c) Al honey comb & fiberglass honey comb structure is used for secondary structural
member
d) Al is used for a particular type of lead only

43. Mark the correct statement

a) if one rivet is tripped, then the adjacent rivets are also tripped in the same direction
b) bearing failure occurs at rivet shank
c) shearing failure occurs at rivet hole

44. Turn & slip indicator measure

a) the amount of tum
b) the rate of tum
c) in slip the amount of tum is too low
d) in skid the amount of tum is too high

45. The acceptable deviation in magnetic compass due to local effects the aircraft is
a) 1
b) 2
c) 3
d) 5

46. Mark the correct statement

a) phosphating on steels prevents corrosion
b) chromatizing is done on aluminium as a protective treatment against corrosion
c) cadmium plating on aluminium penetrates into the base metal there by giving
corrosion resistance
d) all the above

47. In the operation of VSI

a) diaphragm expands in climbing
b) diaphragm shrinks in climbing
c) diaphragm expands & shrinks in level flt
d) both b & c

Part - 3

1. Alloy used for stringer is

a) 7075-T 76
b) 7075-T 6
c) 7075-T 36
d) 7075-T 36&7075-T 73.

2. A+ Aerodynamics center the potching moment Co-efficient is

(a) dependent upon co-efficient of lift (CL)
(b) dependent upon co-efficient of lift & CP
(c) constant and independent of CL
(d) Dependent upon CL& center.

3. Mark the incorrect statement.

(a) For minimum drag the lift co-efficient is equal to its lift dependent drag Co-efficient.
(b) At higher incendents lift arises from difference between reductions on upper & lower
surface of wing.
(c) For thin aerofoil of infinite aspect ratio in super sonic flow the aeroplynic center is at
50% of chord.
(d) Activity factor is measured on power absorption of Air serves.

4.Location of c.p is a function of –Ref page automotive flight

construction.
(a) Camber (b) CL (c) Camber & CL varies with angle of attack (d) Camber varies with
angle of attack

5.The angle of attack at which fail moment is equal to using movement

(a) Neutral point (b) Trim point (c) Stick fixed point (d) Stick free point @ s/p.
 6. Degree of longitudinal stability is effected by relative position of both
(a) Center of pr & aerodynamic center (b) CP & CG
(c) Aerodynamic center & C.G (d) Aerodynamic center & angle of attack.

7. Static Margin is the distance of

(a) Aerodynamics center to neutral point
(b) C.P is neutral point
(c) CP&C.G
(d) CG to neutral point

8. Tab used at high speed

(a) Servo tab
(b) Balance tab
(c) Spring tab
(d) Trim tab 95/F

STRUCTURE
9.The station number is distance in enhance from
(a) A yew reference point forward of fuselage
(b) Reference point on the nose tip
(c) Reference point at wing of empty a/c.
(d) Reference point at the most forwarded C.G point of empty a/c

10. The languorous are

(a) Rolled HAT section
(b) Extracted z sections
(c) Rolled & extracted z sections
(d) Rolled & forged z sections.

11. Extensive use of metal biding in a/c constructions

(a) Fatigue resistance only (b) Corrosion resistance of only power
(c) Fatigue & corrosion resistance (d) corrosion resistance wire

12. Inboard & king of taper rolled provide

(a) Max thickness area of heavy loading
(b) Min thickness area of reduced loading
(c) Thickness skin at root and across fuselage.
(d) Thickness at high tort ional loads

13. Plate between front and rear span

(a) Has thickness tapered
(b) Is butt spliced
(c) Has tapered thickness and is but spliced
(d) Has tapered thickness with flush fastness

14. Alloys use in a/c are hardened by

(a) Cold working (b) Aging (c) Heat treatment (d) Chemical treatment.
 INSTRUMENTS
15.In sensitive ASI the scale can be made liner by
(a) Introducing banana shaped slat in the toothed wheel, which meshes with
pointer percon
(b) using turning spring
(c) Keeping capsule in mathematically curved shape
(d) All the above.

16. Max safe airspeed criclicator

(a) Does not require true temperature compensation
(b) Require true max safe and total Airspeed
(c) Has a subsidiary scales which can be set to max speed of given a/c and structure
(d) None above is correct

17. Mark the correct statement

(a) There is no apparent wander of gyro at equator
(b) If gyro is moved from north pole to south pole around earth surface than the
apparent wonder would change from counter clock wise to clock wise
(c) Error due to apparent wonder at any point is to 15Lat/hr (latitude in degree)
(d) All the above are correct.

18. In ratio meter type instrument

(a) Coil carring stranger current moves in stronger part of it
(b) No effect of flucations of input voltage
(c) Controlling force provided by spring is quit stronger and has to counter balance

19. Artificial Horizon

(a) Has a complete freedom 360 in roll and 85 freedom input is hat it is difficult But not
impossible topple the horizon
(b) Has a wonder rate of gyro less than 15 per hour
(c) Has a gyro axis titled forward about 15 to compensate to rate of turning
(d) All the above are correct.

20. If a/c alternates on easterly heading the compass will indicate

(a) Apparent turn towards north
(b) Apparent turn towards south
(c) Doping of compass
(d) None of the above.

21. Hear spring is a instrument

(a) Is provided to negative back lash and statement
(b) Serves as controlling force against reflecting force
(c) Is strip of Nl, Fe alloy to sensitive to allows greater amount of flux between the pole
to pole temperature when temp increases + statement
(d) None of the above

22. Air speed indicator measures

(a) Dynamic pr (b) Dynamic-static pr (c) Dynamic+static pr (d) Staticpressure
 23. Cabin altitude indicator is
(a) An alternator calibrated to some pr latitude test as a normal altimeter
(b) A bounden type pr gauge
(c) Contains siphon open carbon
(d) None of the above

24. Rate of climb indicator is

(a) A different pr gauge to indicate rate of altitude change
(b) Not a  pr gauge sime operation depends upon static programme
(c) Having, is most cases, a logarithmic scale as it is advantageous in start & statement
(d) Effected by position error

25. Rate of climb indicator

(a) Has two springs for selling range, which bears on stem connected to center piece.
(b) With range setting spring to extent force of capsule to achieve relation between
capsule pr deflection characteristic
(c) Has spring screws the upper row of screws to upper row of spring control rate of
decent calibration
(d) All above the are correct

26. Dip magnetic compass

(a) Is caused by the horizontal component of earths magnetic field
(b) Is called by vertical component of earth magnetic field
(c) Is max at equator & min at poles
(d) Both a & b are correct

27.If pilot tube is blocked airspeed indicator reading while sending will
(a) Decrease (b) Increase (c) under speed (d) over head

28.ASI indicator can be modified to read

(a) Equivalent air speed
(b) Mach numbers
(c) True air speed
(e) All the above

AUTO PILOT

29. In two phase induction motor type of serve motor of an auto pilot the reference
phase is supplied by
(a) 26v 50 Hz (b) 115v, 400Hz (c) 240v, 400Hz (d) 220v, 50

30.When automatic control is selected in electro HYDRAULIC auto pilot system

(a) The engage com is out of detent
(b) Engage signal is fed to the 5.0 volts
(c) a & b
(d) Pilot control valve is operated
 31. The component different between position control servomechanism and speed
control mechanism is
(a) Serve motor (b) Techno generator (c) Potentiono meter (d) error detector

32.Mark the correct statement

(a) Yaw damper will not oppose pedal movement of pilot
(b) The speed monitor identifies speed a/c for application of control
(c) In disengage condition of electro prumatic Autopilot the lines and pistons are
retracted.
(d) Under normal condition of load, the torque applied to input member by servo meter is
transmitted to intermediate member.

33. When control wheel is released in control wheel sterling the automatic control
(a) Holds a/c at originally selected altitude
(b) Is provided by a pilot & Roll forces simultaneously pilot through force transactions
(c) Holds the a/c a newly established altitude
(d) Both b& c correct.

34.Wing leading edge using control achieved by

(a) PrerumaticThermal & thermal system
(b) Thermal & electrical system
(c) Electrical & Alcohol system
(d) All the above

35. Thix tropic Agent

(a) Decreases stress
(b) Decreases temp sensitivity
(c) Increases stress
(d) Increases temp sensitivity

36. Expansion slot in rotary brake discus assembly

(a) Prevents excessive heat description
(b) Prevents warping from heat
(c) Enhance heat disruption
(d) Increases efficiency of brakes system when brakes area

37. Mark the correct statement

(a) Pr demand type of regulator is used for both crews
(b) Pr demand type of regulator is used only for crew

38. Upper & lower bearing in main L/G shock strat programme
(a) Only sliding surface between inner Souter cylinder
(b) Only air seal between inner & outer cylinder
(c) Only sliding surface with minimum friction
(d) Sliding surface and air seal between inner souter cylinder

39. In HYD main L/G system the rate of gear extension is slowed by
(a) In build snubber design
(b) Check valve is upline
(c) Orifice check valve in down line
 (d) Orifice check valve in upline

40. What prevents L/G from being retracted after has lowered
(a) Lock strut (b) Down lock & Lock strut (c) Down lock (d) Down lock & weight of
the a/c

41. Some relief valves provide an overflow features to

(a) To provide pr lock
(b) Prevents cavitations
(c) Test reverse flow chalk valve
(d) Compensate for temperature variation

42. Mark incorrect statement

(a) HYD fuse is device to seal broken HYD line
(b) Follow up selector valves are used in L/G system
(c) Pr relief valves are priority valve
(d) Sequence valves are sprout type and by pass check valves

43. In angular type HYD pump the angle between cylinder block axis and drive shaft axis
can be varied by
(a) Pr control unit
(b) Spring unit
(c) Contrail cylinder
(d) Swivel yoker

44.When sprout type hydraulic pr regulator is in KIKKED” in piston the directional

sprout is in a position to direct pr to
(a) The pilot valve to keep it open
(b) The unloading valve to keep it closed.
(c) The unloading valve to it open
(d) The pilot valve to keep it closed.
45.Fittings used to attach the MLG to wings are secured with
(a) Interference fit
(b) Closed tolerame fit
(c) Both a & b
(d) Permanent type

46. Antiskid system

(a) Can use mechanical fly wheel type of skid detector
(b) Can use electrical & selectronic type skid detector
(c) Provides optimum braking and avoids dragging of wheel
(d) All the above are correct

47. Co lour Hyd system tabbing is

(a) Yellow, blue, Yellow
(b) White, blue, white.
(c) Blue, green, blue
(d) Light blue, Yellow, Colorless.
 PRESSURISATION
48. A line from isobaric control valve to the throat of ambient venture
(a) A low pr reference to manual controller
(b) A low pr reference to auto controller
(c) A high pr reference to manual controller
(d) A high pr reference to auto controller

49. The rate of selection of pressurization system regulates rate of air flow between
(a) Control chamber & venture
(b) Rate chamber & venture
(c) Controller chamber & rate chamber
(d) Rate chamber & manual controller

50. Mark the correct statement

(a) Vacuum relief system provides automatic control signals only
(b) Vacuum relief system provides both auto & manual continue signals only
(c) Positive pr. Relief valve is built in to the flow valve
(d) Cabin barometric selector control landing field altitude

51. The purpose of negative pr relief valve is to

(a) Select pressurization at stations when aerodrome elevation below sea level
(b) Allow out –side air to enter fuselage when out side pr is greater than inside pressure
(c) Allow out flow to open when inside pr greater than ambient
(d) Half differential pr. Relief valve in case ambient pr become less than pr inside
airplane

52.Turbine engine air is used for air conditioning & pressurization cooled
(a) Compressed air (b) Ram air (c) Conditioned air (d) Bleed-Air.

53. How the cabin of an a/c usually controlled

(a) By pressure automatic out flow that dumps all pressure excess of the amount for
which it is
(b) By pr- sensitive valve that consents output of pressurization pump.

54. Cooling device in planes consist of

(a) Fan air, Ram air actuator, ACM
(b) Primary H.E., secondary H.E., and Fam air
(c) ACM, primary H.E., Fam air
(d) ACM, primary H.E., 7 secondary H.E.,

55. Air in pack is at lowest temperature at

(a) Out let of primary H.E.,
(b) Out let of secondary H.E.,
(c) Inlet of compressor
(d) Out let of turbine

56. Out flow valve is for

(a) A./c system only
(b) Pressurization systems only
(c) A/c & pressurization systems only
(d) A/c & recirculation only

57. In the event of pressurization failure protection by

(a) Positive pr. Relief valve
(b) Negative pr. Relief valve
(c) Servo valve
(d) Check valve

58.In pressurization system mode selection switch on ground

(a) For recirculation
(b) For ground operation
(c) For controlling cabin temp on ground
(d) For ground operation of ventilation systems

59. A small orifice in manual control pressurization valve provides

(a) High pr reference for manual controller
(b) High pr reference for auto controller
(c) A low pr reference for manual controller
(d) A low pr reference for auto controller

Part-4

1. Composite with high compressive strength - boron

2. L/G lateral load taken by – Side strut
3. Before fuel tank welding – purge with steam
4. Composite for core – PVC & urathene
5. ‘Flag Out’ goes out of view – when PWR is out
6. Primary structures – Frame & longeron
7. Wing heating due to engine location – will accelerate transition
8. Flap over load valve – Retract flaps to prevent damage.
9. Velocity increases – induced drag decreases
10. L/G down causes – parasite drag
11. Principle of AOA indicting system – not parallel to the true AOA of a/c
12. Definition – wing bitt line
13. Roof skin thickness is – less
14. Stressed skin metal sing subjected to velocity – a group of rivet lead dipping
15. Damage on wing tip & radame – will not affect a/c safety
16. Static pr line disconnected inside pressurized cabin – ASI & altimeter read low
17. L/G down enabling by orifice check valve
18. Brake creeping – contamination of brake linings / glazing
19. To check shock strut fluid level – release air & remove valve
20. Cricket bull seam, rough surface – high Reynolds number, lift
21. T/Reverser principle – Newton’s law
22. Fast erection of gyro hampered by –
23. At the time of installation accelerometer should read + 1G
24. Wind shield made of thermosetting plastic
25. L.E flap made of – Al casting
26. Intergranular corrosion – grain boundaries
27. Sherordizing process – Dipped in molten Zn
28. In a/c, air enter – reheater to turbine
29. Gyros – terrain clearance
30. Spoiler – Assist in roll control
31. Remissible deviation in magnetic compass
32. Compass caliberation, coefficient A is
33. Compass compensation – divide by 8
34. If O2 system pr kept law – moisture accumulating
35. Smoke clearance is part of – A/c system
36. If peak temp goes high – temp control valve modulate close
37. Purpose of fuel tank venting – to prevent damage, collapse suction
38. A stripe mark rim to side wall of tyre. Slippage (creep) identification
39. Annealing makes st. steel – removal stresses, soft machinative
40. Gear type hyd pump is +ve displacement pump because – transfers uniform rol
of fluid in each turn
41. Resistance type temp indicator used – wheel stone bridge circuit
42. Shear between layer takes place – within boundary layer
43. A/C nose tip – stagnation pt, highest pr
44. Plain flap on deflection - effective AOA
Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest

AIRCRAFT AIRFRAME QUE FOR

DGCA & EASA EXAM
1. A new piece of tube cut 10% longer for

1. Bending. 2. Minor vibration in bending 3. Coupling. 4.

None

2. The marking of solid shank rivet head indicates

1. Size of rivet 2. Material of rivet. 3. Head style 4. None

3. Helicoids are precision formed screw thread coils made up of

1.18-8 stainless steel. 2. As in 1 have a circular cross section

3. As in2 &provide protection to the thread cut into casting made of soft metal

4. As in 3 & to be installed in the field when thread in casting are stripped out

4. Grip length of bolt is the

1. Total length of bolt. 2. Length of the threaded portion

3. Length of the unthreaded portion with head. 4. None is correct

5. Chief reason for replacement of cupper tubing by aluminum alloy or CRS tubing is due to

1. Low fatigue factor of copper tube. 2. High fatigue factor of copper tube

3. High aging factor of copper tube

6. External brake lines should be always made of

 1. Monel metal. 2. Annealed CRS. 3. 7075 alloy. 4. 6053 alloy

7. The useful load of an a/c consist of the

1. Crew, Fuel, Passenger, and cargo. 2. Crew, fuel, oil, and fixed equipments

3. Crew, Passenger, fuel, oil, cargo, and fixed equipments,

4. Crew, power plant, fuel, oil, cargo, and passenger

8. In the theory of weight & balance what is the name of distance from the fulcrum to an object

1. Lever arm. 2. Beam length. 3. Balance arm. 4. Fulcrum arm.

9. The empty weight of an airplane is determined by

1. Adding the gross weight on each weighing points and multiplying by the measured distance

to the datum.

2. Adding the net weight of each weighing point and multiplying the measured distance to the
datum

3. Subtracting the tare weight from the scale reading and adding the weight of each weighing
point

4. Multiplying the measure distance from each weighing point to the datum times the sum of scale

reading less the tare weight.

10. When dealing with weight and balance of an a/c, the term maximum weight is interpreted to mean

the minimum

1. Weight of the empty a/c. 2. Weight of the useful load. 3. Authorised weight of a/c and its
contents

4. Weight of all optional or special equipment that can be installed in the a/c.

11. The most important reason for a/c weight and balance control in today a/c is

1. Efficiency in-flight. 2. To reduce noise level. 3. Safety. 4. To increase pay loads.

12. The amount of fuel for computing empty weight and corresponding CG is

1. Empty fuel tanks. 2. Unuseable fuel. 3. Full fuel tanks. 4. The amount of fuel necessary
for ½ an hour of operation.

13. A fuel that vaporize too readily may cause

1. Hard starting. 2. Detonation. 3. Slow warm up. 4. Vapour lock.

14. Characteristics of aviation gasoline are

1. High heat value, high volatility. 2. High heat value, low volatility.

3. Low heat value, high volatility. 4. Low heat value, low volatility.

15. Which of the metal has the most tendencies to oxidize?

 1. Magnesium. 2. Aluminum. 3. Cadmium. 4. Zinc.

16. Stress corrosion can be prevented by

1. Painting the outer surface. 2. Shot peening. 3. Grit blasting. 4. Electroplating.

17. Alodizing is a chemical treatment for aluminum alloy to improve their paint bonding quality and
to

1. Relieve internal stress. 2. Increase corrosion resistance. 3. Decrease corrosion

resistance

4. Making the surface slightly anodic.

18. A chemical treatment to ferrous metal which convert the surface to non metallic oil absorptive
phosphate

coating to reduce wear

1. Bondersing. 2. Colesterising. 3. Granodising. 4. None.

19. Rivet smoking is related to which type of corrosion

1. Fill form. 2. Fretting. 3. Stress. 4. Exfoliation.

20. Which type of corrosion occurs in stainless steel when it is welded?

1. Fretting. 2. Surface. 3. Intergranular. 4. Both 2 & 3 are correct.

21. What is the advantage of a double flare on aluminum tubing?

1. It is less concentric than a single flare. 2. Ease of construction

3. It is less resistant to the shearing effect of torque.

4. It is more resistant to the shearing effect of torque.

22. The maximum distance between end fittings to which a straight hose assembly is to be connected is 50
inches .The minimum hose length to make such a connection should be

1. 54.5 inches. 2. 50-3/4 inch 3. 51 inches. 4. 52-1/2 inches

23. A scratch or nick in aluminum alloy tubing can be repaired by burnishing provided the scratch or nick
does not

1. Exceed 5% of tube diameter. 2. Appear in the heel of a bend in the tube.

3. Exceed 20% of the wall thickness of the tube. 4. Exceed 10 % of the tube dia.

24. If too much time is allowed to elapse during the transfer of 2017 & 2024 aluminums alloy

from the heat treatment medium to the quench tank ,it may result in

1. Case hardening. 2. A dull stained or streaked surface.

3. Retarded age hardening. 4. Impaired corrosion resistance

25. Nitriding is a process in which

 1. Forms a hard case on apart to resist wear. 2. Decrease the size of the grain structure

3. Toughens steel to increase its tensile strength. 4. Increase bearing heat resistance

26. Which type of steel is best suited for case hardening

1. Low carbon, low alloy. 2. High carbon, low alloy.

3. Low carbon high alloy. 4. High carbon, high alloy

27. Aircraft bolts with across or asterisk marked on the bolt head are

1. Made of stainless steel. 2. Made of aluminum alloy.

3. Close tolerance bolt. 4. Standard steel bolt.

28. A fiber type self locking nut must never be used on an a/c if the bolt is

1. Under shear loading. 2. Under tension

loading

3. Subject to rotation. 4. To be removed in a vertical position.

29. What is used to remove corrosion from highly stressed steel surface

1. Steel wire brushes. 2. Fine grit aluminum oxide.

3. High speed wire buffing. 4. Medium grit carborundam paper

30. The interior surface of sealed structural steel tubing is best protected against corrosion by

1. Purging the interior with dry air before sealing. 2. A coating of hot linseed oil.

3. Evacuating the tubing before sealing.

31. In SAE numbering system 2 indicates

1. Nickle steel. 2. Chromium steel. 3. Nickle chromium. 4. Molybdenum steel.

32. The brinell is the

1. Load in kilogram divided by area of the spherical surface of the impression in square inch.

2. Load in pound divided by area of the spherical surface of the impression in square inch.

3. Load in kilogram divided by the area of the spherical surface of the impression in square
mm.

4. Load in pounds multiplied by the area of the spherical surface of the impression in
millimeter.

33. “Penetration hardness “is possessed by

1. Manganese. 2. Nickle. 3. Chromium. 4. Both 1 & 3 are correct

34. In aluminum annealed condition is designated by

 1.”O”. 2. “A”. 3. “H”. 4.”T”.

35. Alclad consists of

1. Pure aluminum coated with an aluminum alloy. 2. Aluminum alloy coated with pure
aluminum.

3. Pure aluminum coated with magnesium alloy. 4. Magnesium alloy coated with pure
aluminum.

36. Hardness is obtained by

1. Slow cooling. 2. Slow heating. 3. Rapid heating. 4. Rapid cooling.

37. Cutting tools retain hardness at dull redness because of presence of

1. Titanium. 2. Cobalt. 3. Tungsten. 4. Molybdenum.

38. While tempering the hardened chisel, the colour of the cutting edge at which it is to be dipped
in water

1. Purple brown. 2. Blue. 3. Brown. 4. Yellow.

39. Anti corrosion treatment given to aluminum alloy is

1. Chromating. 2. Nitriding. 3. Galvanising. 4. Anodising.

40. A double flare should be used on

1. Steel alloy. 2. 2024 al-alloy. 3. 5052 –O al-alloy. 4. None of these.

41. Hi –shear rivets has same shear strength

1. Nuts of equal dia. 2. Bolts of equal dia. 3. Both 1 &2. 4. None

42. Hi-shear rivet are classified as

1. Blind rivet. 2. Self plugging. 3. Mechanical lock rivet. 4. None of the above.

43. The material of the Rivnut is

1. 5053 Al.-alloy. 2. 6063. Al-alloy. 3. 7075 Al- alloy. 4. 1100 Al-alloy.

44. AN 950 washer is

1. Lock washer. 2. Shake proof washer. 3. Ball socket & seat washer. 4. Plain
washer

45. If a tube burst or cracks, it is generally the result of successive

1. Vibration. 2. Improper installation. 3. Collision. 4. All

46. During maintenance of cable in control system.

1. Clean cable by suitable solvent. 2. Clean cable by any type of solvent.

3. Clean cable with wet cloth. 4. Cable should be cleaned with dry cloth.

47. The diameter of DZUS fastener is measure by

 1. 16th of an inch. 2. 100th of an inch.

3. As in 2 and the length of the stud is the distance from the head of the stud to the bottom of

the spring hole.

4. As in 1 & quarter clockwise turn is require to fastened the member.

48. S peed nut are used

1. with self-tapping screw. 2. With machine screw. 3. in non structural location

4. None of the above

49. Re-usable flexible hose fitting uses

1. Swaged fittings. 2. Socket, nut & nipple. 3. Beaded end fitting. 4. All are
correct.

50. The term “aircraft plumbing” refer

1. Hose. 2. Tubing. 3. Fitting. 4. All the above.

51. In magnetic test, which material is non- magnetic

1. Monel. 2. Nickel steel. 3. Pure nickel. 4. None of these.

52. The color code of 3003 al-alloy tubing

1. White. 2. Green. 3. Gray. 4. Red

53. Which type of rubber is an excellent material to used with phosphate ester based hydraulic fluid
(skydrol)

1. Buna-N. 2. Buna-S. 3. But. 4. Neoprene.

54. When safety-wiring closely spaced bolts

1. A group of three should be the maximum in series.

2. Number that can be safety-wired by a 24” length of wire is the maximum in a series.

3. A group of five should be the maximum in a series.

4. There is no such restriction in safety wiring.

55. Grub screw

1. Is a headless screw. 2. Has round head. 3. Flat

head

4. As in 1 and used with self locking nut

56. Which nut should not be used when temp is more than 2500C

1. Elastic stop nut. 2. Sheet spring nut. 3. Boots self locking nut.

57. Shake proof lock washer are

 1. Round washer. 2. As in (1) and designed with tabs

3. As in (2) and tap is bent upwards. 4. As in (3) and tab is bent downwards.

58. The materials of studs of dzus fasteners

1. Steel and cadmium plated. 2. Steel and chromium plated.

3. As in (1) and designed in 3 head style. 4. As in (2) and designed in 3 head style.

59. A/C control cables are fabricated from

1. Carbon steel. 2. Stainless steel. 3. Both 1and 2 are correct.

4. None.

60. The contamination of water in aviation Fuel is permitted upto

1. 30 PPM. 2. 20 PPM. 3. 7 PPM.

61. What is the purpose of Lump Valve

1. To jettison the fuel. 2. To transfer fuel from one tank to other.

3. To dump the fuel after emergency.

62. The special washer used with Internal wrenching bolt is

1. NAS 143 & 143C. 2. MS 20002 & MS 20002C. 3. Both 1 and 2 are correct.

4. NAS 143 & MS 20002.

63. The bolt head is marked with either recessed or raised triangle, the bolt is

1. NAS close tolerance bolt. 2. Close tolerance bolt. 3. Std bolt. 4.CAS bolt.

64. The length of clevis bolt is measured in

1. 16th of an inch. 2. 8th of an inch. 3. 32nd of an inch.

65. Incase of ‘V’ rings the open end of V should always be

1. Face the pressure. 2. Away from the pressure. 3. Anyway can be put.

66. Wipers are

1. Static seals. 2. Used to clean exposed portion of piston shafts

3. As in (2) also prevents dirt entering the system. 4. As in (3) & made of Neoprene.

67. Anodising is a chemical treatment

1. For all Al alloys. 2. Only clad surface. 3. Only Non-clad surfaces.

4. As per situation it demands.

68. What is to be used to clean surfaces oil, hyd fluid, grease from a/c tyre

1. Aliphatic Naptha. 2. Aromatic Naptha. 3. Mild soap solution. 4. Water.

 69. MS 20470 is a

1. Flat head rivet. 2. CSK head rivets. 3. Brazier head. 4. Universal head
rivets.

70. If a rivets is marked with recessed double dots on its head, the rivets is

1. Monel. 2. Aluminium. 3. Brass. 4. Titanium.

71. The letter F indicates that rivets materials is

1. CRS. 2. Carbon steel. 3. Inconel. 4. None.

72. Tank lining for aromatic aviation gasoline is made of

1. Buna. 2. Neoprene. 3. Thikol. 4. Butyl rubber.

73. Magnesium alloy casting are solution heat treated

1. To lower tensile & ductility. 2. As in (1) & also shock resistance.

3. As in (1) & also shock resistance. 4. All are correct.

74. Most widely used alloy in a/c construction are hardened by

1. Heat treatment. 2. Cold worked. 3. Hot worked. 4. None

75. Which of the following is having lowest fusing temperature

1. Eutectoid. 2. Hypo-eutectoid. 3. Hyper-eutectoid. 4. Pearlite.

76. Black pitting & reddish brown corrosion occurs on

1. CRS. 2. Cast Iron. 3. Magnesium. 4. Aluminium.

77. AN 545 is a

1. Machine screw nut. 2. Slotted engine nut. 3. Wing nut. 4. Shear castle nut.

78. Type of rivet to be installed on an aerodynamically smooth surface or if clearance of an assembly is

needed

1. CSK rivets. 2. Round head. 3. Flat head. 4. Brazier head.

79. Alclad surfaces

1. Are to be left unpainted. 2. As in (1) & require no anodic treatment. 3. Both

statements are wrong.

80. Solvent & Emulsion type cleaner are

1. Heavy duty cleaner. 2. Light duty cleaner. 3. Medium duty cleaner. 4. All the
above.