Scribd
Upload
232 views

Lecture 6

- An angular contact ball bearing is to be selected for location C to support a thrust load, and a cylindrical roller bearing is to be selected for location D to support a radial load. - For location D, a 02-25mm or 03-25mm cylindrical roller bearing is selected from the catalog with a radial load rating greater than 316 lbf. - For location C, an iterative process is used to select an angular contact ball bearing to support the 464.4 lbf radial load and 356.6 lbf thrust load. The process involves choosing values from tables 11-1 and 11-2 until a consistent bearing is selected.

Uploaded by

Gianardo Satria Primandanu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
232 views

Lecture 6

- An angular contact ball bearing is to be selected for location C to support a thrust load, and a cylindrical roller bearing is to be selected for location D to support a radial load. - For location D, a 02-25mm or 03-25mm cylindrical roller bearing is selected from the catalog with a radial load rating greater than 316 lbf. - For location C, an iterative process is used to select an angular contact ball bearing to support the 464.4 lbf radial load and 356.6 lbf thrust load. The process involves choosing values from tables 11-1 and 11-2 until a consistent bearing is selected.

Uploaded by

Gianardo Satria Primandanu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 33

Q2(13p).A gear-reduction unit uses the countershaft depicted in the figure.

Find the
two bearing reactions.The bearings are to be angular-contact ball bearings, having
a desired life of 50 kh when used at 400 rev/min. Use 1.2 for the application factor
and a reliability goal for the bearing pair of 0.98.
a-Select the bearings from Table 11–2.

T=10(180cos40)=-1378.9lbf.in
T1+T2=0
F=1378.9/5cos25=304.28 lbf

Ryc=131.4
Ryc-180sin40-Fsin25+Roy=
Roy=112.86
Rcz=-153.2
Roz=Fcos25-180cos40-153.2= 15.136
Ro=15.12 +112.862=114.24 113.95
Rc=153.22+131.42=201.8
11-6 Combined Radial and Thrust Loading

Bearings are usually operated with some combination of radial and thrust load.
Catalog ratings are based only on radial loads. Follow the guideline in catalogs to
obtain the equivalent radial load.
In order to choose the bearing, an equivalent radial load Fe must be found
How to handle combined loading

• What about combined radial, Fr, and axial loading , Fa?


– Use an equivalent load, Fe, that does the same amount of
damage.

Fe  X i V Fr  Yi Fa
• Where V = 1.2 for outer ring rotation and 1 for inner ring
– This has to do with the fact that outer ring fails more often
• Xi and Yi are a function of the
– Axial load, Fa
– Static load rating, Co
M is specified asgiven in this table.
A ball bearing is capable of resisting radial loading and a thrust loading. These can be
combined.
• Fa = the axial th ust load.
• F = the adial load.
• Fe = e uivale t adial load that does the sa e da age as the combined radial and
thrust loads together.
• The a s issa e is defined by the intersection of the two lines.

V=1 when the inner ring rotates


V=1.2 when the outer ring rotates

X> the intercept of the line with vertical


Angular Contact Bearings

To attain high stiffness and load capacity:


 Two, three, or four (or more) bearings can be
used forming Duplex,
Triplex, or Quadruplex sets:
Bearing Specifications

Bearings are defined by a two digit number: dimension-series code


First number is the width series, 0,1,2,3,4,5 and 6

Second number is the diameter series Dimension series for radial bearings
Bearing Specifications
ABMA Boundary Dimensions
Ex:An SKF 6210 angular-contact ball bearing (a=3)has an axial
load Fa of 1.8 kN applied, a radial load Fr of 2.2 kN applied with
the outer ring stationary. The basic static load rating C0is 19.8kN
and the basic load rating C10is 35 kN.
Estimate the LD life at a speed of 720 r/min.

V=1 and Fa/Co=1.8/19.8=0.09


Interpolate for e in Table 11-1; e= 0.285
since Fa/ (VFr)=1800/ [(1)2200]=0.818
Interpolate Y2
Fe=X2VFr+Y2Fa=0.56(1)2.2+1.527(1.8)=3.96kN
11-7 Variable Loading

Equation (11–1) can be written as


FaL = constant = K

If a load level of F1 is selected and run to


the failure criterion, then the area under
the F1-L1 trace is numerically equal to K.
The same is true for a load level F2; that
is, the area under the F2-L2 trace is
numerically equal to K
load level F1, the area from L = 0 to L = L A does damage measured by Fa L A = D.

The damage done by loads Fe1, Fe2, and Fe3 is

The equivalent steady load Feq when


run for l1 + l2 + l3 revolutions does the same
damage D.

fi is the fraction of revolution run up under load Fei


Fei are equivalent steady radial loads for combined radial–thrust loads
Since li can be expressed as ni ti , where ni is the rotational speed at load Fei and ti is the
duration of that speed, then it follows that

The character of the individual loads can change, so an application factor (af ) can
be prefixed to each Fei as (af i Fei )a ;
Selection of ball and cylindrical roller bearing

This selection procedure contains an iterative


process:
-Choose Y2from Table 11-1
-Find C10
-Tentatively indentifya suitable bearing 11-2, note Co
-Using Fa/Coenter Table 11-1 to obataina new value
of Y2
-If the same bearing is obtain, stop
-If not, take next bearing and go to step 4.
11–8 Selection of Ball and Cylindrical Roller Bearings
Ex- The second shaft on a parallel-shaft 25-hp foundry crane speed
reducer contains a helical gear with a pitch diameter of 8.08 in.
Helical gears transmit components of force in the tangential, radial,
and axial directions . The components of the gear force transmitted
to the second shaft are shown in the Figure below at point A.
The bearing reactions at C and D, assuming simple-supports, are also
shown. A ball bearing is to be selected for location C to accept the
thrust, and a cylindrical roller bearing is to be utilized at location D.
The life goal of the speed reducer is 10 kh, with a reliability factor for
the assembly of all four bearings (both shafts) to equal or exceed
0.96 for the Weibull parameters are b=1.483, X0= 0.2,
=4.439+0.2. The application factor is to be 1.2.
(a) Select the roller bearing for location D.
(b) Select the ball bearing (angular contact) for location C, assuming
the inner ring rotates.
The torque transmitted is T = 595(4.04) = 2404 lbf.in

The speed at the rated horse power,

-The radial load at D is √106.62 + 297.52 = 316.0 lbf,


-the radial load at C is
√356.62 + 297.52 = 464.4 lbf
The individual bearing reliabilities, if equal, must be
2 bearing for each shaft so at least 4√ 0.96 = 0.98985 .= 0.99
The dimensionless design life for both bearings is
a = 10/3 for the roller bearing at D, the catalog rating should be
equal to or Greater than

Choose a 02-25 mm series, or a 03-25 mm series cylindrical roller bearing from Table
11–3.
The ball bearing at C involves a thrust component. This selection
procedure requires an iterative procedure. Assuming Fa/(V Fr) > e,

1 Choose Y2 from Table 11–1.


2 Find C10.
3 Tentatively identify a suitable bearing from Table 11–2, note C0.
4 Using Fa/C0 enter Table 11–1 to obtain a new value of Y2.
5 Find C10.
6 If the same bearing is obtained, stop.
7 If not, take next bearing and go to step 4.

take the middle entry from Table 11–1:


X2 = 0.56 Y2 = 1.63.
The life goal of the speed reducer is 10kh. The desired speed is 656 rev/min.

You might also like