3 Introduction to Dynamic Routing Protocols

3.0 Chapter Introduction

3.0.1 Chapter Introduction

The data networks that we use in our everyday lives to learn, play, and work range from small, local networks
to large, global internetworks. At home, you may have a router and two or more computers. At work, your
organization may have multiple routers and switches servicing the data communication needs of hundreds or
even thousands of PCs.

Dynamic routing protocols are usually used in larger networks to ease the administrative and operational
overhead of using only static routes. Typically, a network uses a combination of both a dynamic routing
protocol and static routes. In most networks, a single dynamic routing protocol is used, however there are cases
where different parts of the network may use different routing protocols.

Since the early 1980's, several different dynamic routing protocols have emerged.

Although many networks will only use a single routing protocol or use only static routes, it is important for a
network professional to understand the concepts and operations of all the different routing protocols. A network
professional must be able to make an informed decision regarding when to use a dynamic routing protocol and
which routing protocol is the best choice for a particular environment.

3.1 Introduction and Advantages

3.1.1 Perspective and Background

The Evolution of Dynamic Routing Protocols

Dynamic routing protocols have been used in networks since the early 1980s. The first version of RIP was
released in 1982, but some of the basic algorithms within the protocol were used on the ARPANET as early as
1969.

As networks have evolved and become more complex, new routing protocols have emerged.

One of the earliest routing protocols was Routing Information Protocol (RIP). RIP has evolved into a newer
version RIPv2. However, the newer version of RIP still does not scale to larger network implementations. To
address the needs of larger networks, two advanced routing protocols were developed: Open Shortest Path First
(OSPF) and Intermediate System-to-Intermediate System (IS-IS). Cisco developed Interior Gateway Routing
Protocol (IGRP) and Enhanced IGRP (EIGRP), which also scales well in larger network implementations.

Additionally, there was the need to interconnect different internetworks and provide routing among them.
Border Gateway Routing (BGP) protocol is now used between ISPs as well as between ISPs and their larger
private clients to exchange routing information.

With the advent of numerous consumer devices using IP, the IPv4 addressing space is nearly exhausted. Thus
IPv6 has emerged. To support the communication based on IPv6, newer versions of the IP routing protocols
have been developed.

The Role of Dynamic Routing Protocol

What exactly are dynamic routing protocols? Routing protocols are used to facilitate the exchange of routing
information between routers. Routing protocols allow routers to dynamically share information about remote
networks and automatically add this information to their own routing tables.

Routing protocols determine the best path to each network which is then added to the routing table. One of the
primary benefits to using a dynamic routing protocol is that routers exchange routing information whenever
there is a topology change. This exchange allows routers to automatically learn about new networks and also to
find alternate paths when there is a link failure to a current network.

Compared to static routing, dynamic routing protocols require less administrative overhead. However, the
expense of using dynamic routing protocols is dedicating part of a router's resources for protocol operation
including CPU time and network link bandwidth. Despite the benefits of dynamic routing, static routing still has
its place. There are times when static routing is more appropriate and other times when dynamic routing is the
better choice. More often than not, you will find a combination of both types of routing in any network that has
a moderate level of complexity. We will discuss the advantages and disadvantages of static and dynamic routing
later in this chapter.

3.1.2 Network discovery and routing table maintenance

The Purpose of Dynamic Routing Protocols

A routing protocol is a set of processes, algorithms, and messages that are used to exchange routing information
and populate the routing table with the routing protocol's choice of best paths. The purpose of a routing protocol
includes:

 Discovery of remote networks

 Maintaining up-to-date routing information
 Choosing the best path to destination networks
 Ability to find a new best path if the current path is no longer available

What are the components of a routing protocol?

 Data structures - Some routing protocols use tables and/or databases for its operations. This
information is kept in RAM.
 Algorithm - An algorithm is a finite list of steps used in accomplishing a task. Routing protocols use
algorithms for facilitating routing information and for best path determination.
 Routing protocol messages - Routing protocols use various types of messages to discover neighboring
routers, exchange routing information, and other tasks to learn and maintain accurate information about
the network.

Dynamic Routing Protocol Operation

All routing protocols have the same purpose - to learn about remote networks and to quickly adapt whenever
there is a change in the topology. The method that a routing protocol uses to accomplish this depends upon the
algorithm it uses and the operational characteristics of that protocol. The operations of a dynamic routing
protocol vary depending upon the type of routing protocol and the routing protocol itself. In general, the
operations of a dynamic routing protocol can be described as follows:

 The router sends and receives routing messages on its interfaces.

 The router shares routing messages and routing information with other routers that are using the same
routing protocol.
  Routers exchange routing information to learn about remote networks.
 When a router detects a topology change the routing protocol can advertise this change to other routers.

Note: Understanding dynamic routing protocol operation and concepts and using them in real networks requires
a solid knowledge of IP addressing and subnetting. Three subnetting scenarios are available at the end of this
chapter for your practice.

3.1.3 Advantages

Static Routing Usage

Before identifying the benefits of dynamic routing protocols, we need to consider the reasons why we would
use static routing. Dynamic routing certainly has several advantages over static routing. However, static routing
is still used in networks today. In fact, networks typically use a combination of both static and dynamic routing.

Static routing has several primary uses, including:

 Providing ease of routing table maintenance in smaller networks that are not expected to grow
significantly.
 Routing to and from stub networks (see Chapter 2).
 Use of a single default route, used to represent a path to any network that does not have a more specific
match with another route in the routing table.

Static Routing Advantages and Disadvantages

In the table dynamic and static routing features are directly compared. From this comparison, we can list the
advantages of each routing method. The advantages of one method are the disadvantages of the other.

Static routing advantages:

 Minimal CPU processing.

 Easier for administrator to understand.
 Easy to configure.
 Static routing disadvantages:

 Configuration and maintenance is time-consuming.

 Configuration is error-prone, especially in large networks.
 Administrator intervention is required to maintain changing route information.
 Does not scale well with growing networks; maintenance becomes cumbersome.
 Requires complete knowledge of the whole network for proper implementation.

Dynamic Routing Advantages and Disadvantages

Dynamic routing advantages:

 Administrator has less work maintaining the configuration when adding or deleting networks.
 Protocols automatically react to the topology changes.
 Configuration is less error-prone.
 More scalable, growing the network usually does not present a problem.
Dynamic routing disadvantages:

 Router resources are used (CPU cycles, memory and link bandwidth).
 More administrator knowledge is required for configuration, verification, and troubleshooting.

3.2 Classifying Dynamic Routing Protocols

3.2.1 Overview

Dynamic Routing Protocols Classification

Routing protocols can be classified into different groups according to their characteristics. The most commonly
used routing protocols are:

 RIP - A distance vector interior routing protocol

 IGRP - The distance vector interior routing developed by Cisco (deprecated from 12.2 IOS and later)
 OSPF - A link-state interior routing protocol
 IS-IS - A link-state interior routing protocol
 EIGRP - The advanced distance vector interior routing protocol developed by Cisco
 BGP - A path vector exterior routing protocol

Note: IS-IS and BGP are beyond the scope of this course and are covered in the CCNP curriculum.

The classification criteria are explained later in this chapter.

3.2.2 IGP and EGP

An autonomous system (AS) - otherwise known as a routing domain - is a collection of routers under a common
administration. Typical examples are a company's internal network and an Internet service provider's network.
Because the Internet is based on the autonomous system concept, two types of routing protocols are required:
interior and exterior routing protocols. These protocols are:

 Interior Gateway Protocols (IGP) are used for intra-autonomous system routing - routing inside an
autonomous system.
 Exterior Gateway Protocols (EGP) are used for inter-autonomous system routing - routing between
autonomous systems.

The figure is a simplified view of the difference between IGPs and EGPs. The autonomous system concept will
be explained in more detail later in the chapter.

Characteristics of IGP and EGP Routing Protocols

IGPs are used for routing within a routing domain, those networks within the control of a single organization.
An autonomous system is commonly comprised of many individual networks belonging to companies, schools,
and other institutions. An IGP is used to route within the autonomous system, and also used to route within the
individual networks themselves. For example, CENIC operates an autonomous system comprised of California
schools, colleges and universities. CENIC uses an IGP to route within its autonomous system in order to
interconnect all of these institutions. Each of the educational institutions also uses an IGP of their own choosing
to route within its own individual network. The IGP used by each entity provides best path determination within
its own routing domains, just as the IGP used by CENIC provides best path routes within the autonomous
system itself. IGPs for IP include RIP, IGRP, EIGRP, OSPF, and IS-IS.
Routing protocols, and more specifically the algorithm used by that routing protocol, use a metric to determine
the best path to a network. The metric used by the routing protocol RIP is hop count, which is the number of
routers that a packet must traverse in reaching another network. OSPF uses bandwidth to determine the shortest
path.

EGPs on the other hand, are designed for use between different autonomous systems that are under the control
of different administrations. BGP is the only currently-viable EGP and is the routing protocol used by the
Internet. BGP is a path vector protocol that can use many different attributes to measure routes. At the ISP level,
there are often more important issues than just choosing the fastest path. BGP is typically used between ISPs
and sometimes between a company and an ISP. BGP is not part of this course or CCNA; it is covered in CCNP.

In this activity, the network has already been configured within the autonomous systems. You will configure a
default route from AS2 and AS3 (two different companies) to the ISP (AS1) to simulate the Exterior Gateway
Routing that would take place from both companies to their ISP. Then you will configure a static route from the
ISP (AS1) to AS2 and AS3 to simulate the Exterior Gateway Routing that would take place from the ISP to its 2
customers AS2 and AS3. View the routing table before and after both static routes and default routes are added
to observe how the routing table has changed.

3.2.3 Distance Vector and Link State

Interior Gateway Protocols (IGPs) can be classified as two types:

 Distance vector routing protocols

 Link-state routing protocols

Distance Vector Routing Protocol Operation

Distance vector means that routes are advertised as vectors of distance and direction. Distance is defined in
terms of a metric such as hop count and direction is simply the next-hop router or exit interface. Distance vector
protocols typically use the Bellman-Ford algorithm for the best path route determination.

Some distance vector protocols periodically send complete routing tables to all connected neighbors. In large
networks, these routing updates can become enormous, causing significant traffic on the links.

Although the Bellman-Ford algorithm eventually accumulates enough knowledge to maintain a database of
reachable networks, the algorithm does not allow a router to know the exact topology of an internetwork. The
router only knows the routing information received from its neighbors.

Distance vector protocols use routers as sign posts along the path to the final destination. The only information
a router knows about a remote network is the distance or metric to reach that network and which path or
interface to use to get there. Distance vector routing protocols do not have an actual map of the network
topology.

Distance vector protocols work best in situations where:

 The network is simple and flat and does not require a special hierarchical design.
 The administrators do not have enough knowledge to configure and troubleshoot link-state protocols.
 Specific types of networks, such as hub-and-spoke networks, are being implemented.
 Worst-case convergence times in a network are not a concern.
Distance vector routing protocol functions and operations will be explained in the next chapter. You will also
learn about the operations and configuration of the distance vector routing protocols RIP and EIGRP.

Link-state Protocol Operation

In contrast to distance vector routing protocol operation, a router configured with a link-state routing protocol
can create a "complete view" or topology of the network by gathering information from all of the other routers.
To continue our analogy of sign posts, using a link-state routing protocol is like having a complete map of the
network topology. The sign posts along the way from source to destination are not necessary, because all link-
state routers are using an identical "map" of the network. A link-state router uses the link-state information to
create a topology map and to select the best path to all destination networks in the topology.

With some distance vector routing protocols, routers send periodic updates of their routing information to their
neighbors. Link-state routing protocols do not use periodic updates. After the network has converged, a link-
state update only sent when there is a change in the topology. For example, the link-state update in the
animation is not sent until the 172.16.3.0 network goes down.

Link-state protocols work best in situations where:

 The network design is hierarchical, usually occurring in large networks.

 The administrators have a good knowledge of the implemented link-state routing protocol.
 Fast convergence of the network is crucial.

Link-state routing protocol functions and operations will be explained in later chapters. You will also learn
about the operations and configuration of the link-state routing protocol OSPF.

3.2.4 Classful and Classless

Classful Routing Protocols

Classful routing protocols do not send subnet mask information in routing updates. The first routing
protocols such as RIP, were classful. This was at a time when network addresses were allocated based on
classes, class A, B, or C. A routing protocol did not need to include the subnet mask in the routing update
because the network mask could be determined based on the first octet of the network address.

Classful routing protocols can still be used in some of today's networks, but because they do not include the
subnet mask they cannot be used in all situations. Classful routing protocols cannot be used when a network is
subnetted using more than one subnet mask, in other words classful routing protocols do not support variable
length subnet masks (VLSM).

There are other limitations to classful routing protocols including their inability to support discontiguous
networks. Classful routing protocols, discontiguous networks and VLSM will all be discussed in later chapters.

Classful routing protocols include RIPv1 and IGRP.

Classless Routing Protocols

Classless routing protocols include the subnet mask with the network address in routing updates. Today's
networks are no longer allocated based on classes and the subnet mask cannot be determined by the value of the
first octet. Classless routing protocols are required in most networks today because of their support for VLSM,
discontiguous networks and other features which will be discussed in later chapters.

In the figure, notice that the classless version of the network is using both /30 and /27 subnet masks in the same
topology. Also notice that this topology is using a discontiguous design.

Classless routing protocols are RIPv2, EIGRP, OSPF, IS-IS, BGP.

3.2.5 Convergence

What is Convergence?

Convergence is when all routers' routing tables are at a state of consistency. The network has converged when
all routers have complete and accurate information about the network. Convergence time is the time it takes
routers to share information, calculate best paths, and update their routing tables. A network is not completely
operable until the network has converged; therefore, most networks require short convergence times.

Convergence is both collaborative and independent. The routers share information with each other but must
independently calculate the impacts of the topology change on their own routes. Because they develop an
agreement with the new topology independently, they are said to converge on this consensus.

Convergence properties include the speed of propagation of routing information and the calculation of optimal
paths. Routing protocols can be rated based on the speed to convergence; the faster the convergence, the better
the routing protocol. Generally, RIP and IGRP are slow to converge, whereas EIGRP and OSPF are faster to
converge.

3.3 Metrics

3.3.1 Purpose of a Metric

There are cases when a routing protocol learns of more than one route to the same destination. To select the best
path, the routing protocol must be able to evaluate and differentiate between the available paths. For this
purpose a metric is used. A metric is a value used by routing protocols to assign costs to reach remote
networks. The metric is used to determine which path is most preferable when there are multiple paths to the
same remote network.

Each routing protocol uses its own metric. For example, RIP uses hop count, EIGRP uses a combination of
bandwidth and delay, and Cisco's implementation of OSPF uses bandwidth. Hop count is the easiest metric to
envision. The hop count refers to the number of routers a packet must cross to reach the destination network.
For R3 in the figure, network 172.16.3.0 is two hops, or two routers away.

Note: The metrics for a particular routing protocol and how they are calculated will be discussed in the chapter
for that routing protocol.

3.3.2 Metrics and Routing Protocols

The Metric Parameters

Different routing protocols use different metrics. The metric used by one routing protocol is not comparable to
the metric used by another routing protocol. Two different routing protocols might choose different paths to the
same destination due to using different metrics.

RIP would choose the path with the least amount of hops, whereas OSPF would choose the path with the
highest bandwidth.

Metrics used in IP routing protocols include:

 Hop count - A simple metric that counts the number of routers a packet must traverse
 Bandwidth - Influences path selection by preferring the path with the highest bandwidth
 Load - Considers the traffic utilization of a certain link
 Delay - Considers the time a packet takes to traverse a path
 Reliability - Assesses the probability of a link failure, calculated from the interface error count or
previous link failures
 Cost - A value determined either by the IOS or by the network administrator to indicate preference for a
route. Cost can represent a metric, a combination of metrics or a policy.

Note: At this point, it is not important to completely understand these metrics; they will be explained in later
chapters.

The Metric Field in the Routing Table

The metric for each routing protocol is:

 RIP: Hop count - Best path is chosen by the route with the lowest hop count.
 IGRP and EIGRP: Bandwidth, Delay, Reliability, and Load - Best path is chosen by the route with the
smallest composite metric value calculated from these multiple parameters. By default, only bandwidth
and delay are used.
 IS-IS and OSPF: Cost - Best path is chosen by the route with the lowest cost. . Cisco's implementation
of OSPF uses bandwidth. IS-IS is discussed in CCNP.

Routing protocols determine best path based on the route with the lowest metric.

Refer to the example in the figure The routers are using the RIP routing protocol. The metric associated with a
certain route can be best viewed using the show ip route command. The metric value is the second value in the
brackets for a routing table entry. In the figure, R2 has a route to the 192.168.8.0/24 network that is 2 hops
away.

R 192.168.8.0/24 [120/2] via 192.168.4.1, 00:00:26, Serial0/0/1

Note: More detailed information about specific routing protocol metrics and how to calculate them will be
available in the later chapters describing the individual routing protocols.

3.3.3 Load Balancing

We have discussed that individual routing protocols use metrics to determine the best route to reach remote
networks. But what happens when two or more routes to the same destination have identical metric values?
How will the router decide which path to use for packet forwarding? In this case, the router does not choose
only one route. Instead, the router "load balances" between these equal cost paths. The packets are
forwarded using all equal-cost paths.

To see whether load balancing is in effect, check the routing table. Load balancing is in effect if two or more
routes are associated with the same destination.

Note: Load balancing can be done either per packet or per destination. How a router actually load balances
packets between the equal-cost paths is governed by the switching process. The switching process will be
discussed in greater detail in a later chapter.

Play the animation.

R2 load balances traffic to PC5 over two equal cost paths.

The show ip route command reveals that the destination network 192.168.6.0 is available through 192.168.2.1
(Serial 0/0/0) and 192.168.4.1 (Serial 0/0/1).

R 192.168.6.0/24 [120/1] via 192.168.2.1, 00:00:24, Serial0/0/0

[120/1] via 192.168.4.1, 00:00:26, Serial0/0/1

All the routing protocols discussed in this course are capable of automatically load balancing traffic for up to
four equal-cost routes by default. EIGRP is also capable of load balancing across unequal-cost paths. This
feature of EIGRP is discussed in the CCNP.

3.4 Administrative Distances

3.4.1 Purpose of Administrative Distance

Multiple Routing Sources

We know that routers learn about adjacent networks that are directly connected and about remote networks by
using static routes and dynamic routing protocols. In fact, a router might learn of a route to the same network
from more than one source. For example, a static route might have been configured for the same network/subnet
mask that was learned dynamically by a dynamic routing protocol, such as RIP. The router must choose which
route to install.

Note: You might be wondering about equal cost paths. Multiple routes to the same network can only be
installed when they come from the same routing source. For example, for equal cost routes to be installed they
both must be static routes or they both must be RIP routes.

Although less common, more than one dynamic routing protocol can be deployed in the same network. In some
situations it may be necessary to route the same network address using multiple routing protocols such as RIP
and OSPF. Because different routing protocols use different metrics, RIP uses hop count and OSPF uses
bandwidth, it is not possible to compare metrics to determine the best path.

So, how does a router determine which route to install in the routing table when it has learned about the same
network from more than one routing source?
The Purpose of Administrative Distance

Administrative distance (AD) defines the preference of a routing source. Each routing source - including
specific routing protocols, static routes, and even directly connected networks - is prioritized in order of most-
to least-preferable using an administrative distance value. Cisco routers use the AD feature to select the best
path when it learns about the same destination network from two or more different routing sources.

Administrative distance is an integer value from 0 to 255. The lower the value the more preferred the route
source. An administrative distance of 0 is the most preferred. Only a directly connected network has an
administrative distance of 0, which cannot be changed.

It is possible to modify the administrative distance for static routes and dynamic routing protocols. This is
discussed in CCNP.

An administrative distance of 255 means the router will not believe the source of that route and it will not be
installed in the routing table.

Note: The term trustworthiness is commonly used when defining administrative distance. The lower the
administrative distance value the more trustworthy the route.

Click show ip route in the figure.

The AD value is the first value in the brackets for a routing table entry. Notice that R2 has a route to the
192.168.6.0/24 network with an AD value of 90.

D 192.168.6.0/24 [90/2172416] via 192.168.2.1, 00:00:24, Serial0/0/0

R2 is running both RIP and EIGRP routing protocols. (Remember: it is not common for routers to run multiple
dynamic routing protocols, but is used here to demonstrate how administrative distance works.) R2 has learned
of the 192.168.6.0/24 route from R1 through EIGRP updates and from R3 through RIP updates. RIP has an
administrative distance of 120, but EIGRP has a lower administrative distance of 90. So, R2 adds the route
learned using EIGRP to the routing table and forwards all packets for the 192.168.6.0/24 network to router R1.

Click show ip rip database in the figure.

What happens if the link to R1 becomes unavailable? Then R2 would not have a route to 192.168.6.0. Actually,
R2 still has the RIP route information for 192.168.6.0 stored in the RIP database. This can be verified with the
show ip rip database command. This command shows all RIP routes learned by R2, whether or not the RIP
route is installed in the routing table.

3.4.2 Dynamic Routing Protocols

Click show ip route in the figure.

You already know that you can verify these AD values with the show ip route command.

Click show ip protocols in the figure.

The AD value can also be verified with the show ip protocols command. This command displays all pertinent
information about routing protocols operating on the router. We will look at the show ip protocols command in
detail many times during the rest of the course. However, for now notice the highlighted output: R2 has two
routing protocols listed and the AD value is called Distance.

Click AD Table in the figure.

Notice the different administrative distance values for various routing protocols.

3.4.3 Static Routes

As you know from Chapter 2, static routes are entered by an administrator who wants to manually configure the
best path to the destination. For that reason, static routes have a default AD value of 1. This means that after
directly connected networks, which have a default AD value of 0, static routes are the most preferred route
source.

There are situations when an administrator will configure a static route to the same destination that is learned
using a dynamic routing protocol, but using a different path. The static route will be configured with an AD
greater than that of the routing protocol. If there is a link failure in the path used by the dynamic routing
protocol, the route entered by the routing protocol is removed from the routing table. The static route will then
become the only source and will automatically be added to the routing table. This is known as a floating static
route and is discussed in CCNP.

A static route using either a next-hop IP address or an exit interface has a default AD value of 1. However, the
AD value is not listed in show ip route when you configure a static route with the exit interface specified.
When a static route is configured with an exit interface, the output shows the network as directly connected via
that interface.

Click show ip route in the figure.

The static route to 172.16.3.0 is listed as directly connected. However, there is no information on what the AD
value is. It is a common misconception to assume that the AD value of this route must be 0 because it states
"directly connected." However, that is a false assumption. The default AD of any static route, including those
configured with an exit interface is 1. Remember, only a directly connected network can have an AD of 0. This
can be verified by extending the show ip route command with the [route] option. Specifying the [route]
reveals detailed information about the route, including its distance, or AD value.

Click show ip route 172.16.3.0 in the figure.

The command show ip route 172.16.3.0 reveals that, in fact, the administrative distance is 1.

3.4.4 Directly Connected Networks

Directly connected networks appear in the routing table as soon as the IP address on the interface is configured
and the interface is enabled and operational. The AD value of directly connected networks is 0, meaning that
this is the most preferred routing source. There is no better route for a router than having one of its interfaces
directly connected to that network. For that reason, the administrative distance of a directly connected network
cannot be changed and no other route source can have an administrative distance of 0.

Click show ip route in the figure.

The output of the show ip route command displays the directly connected networks with no information about
the AD value. The output is similar to the output for static routes that point to an exit interface. The only
difference is the letter C at the beginning of the entry, which indicates that this is a directly connected network.
To see the AD value of a directly connected network, use the [route] option.

Click show ip route 172.16.1.0 in the figure.

The show ip route 172.16.1.0 command reveals that the distance is 0 for that directly connected route.

3.5 Routing Protocols and Subnetting Activities

3.5.1 Identifying Elements of the Routing Table

The purpose of this exercise is to practice how to correctly identify the route source, administrative distance,
and metric for a given route based on output from the show ip route command.

The output is not common for most routing tables. Running more than one routing protocol on the same router
is rare. Running three, as shown here, is more of an academic exercise and has value in that it will help you
learn to interpret the routing table output.

Drag and drop the appropriate responses to the corresponding space in the table.

 Use the information from the Show IP Route as reference.

 Not all answers are used.
 Some answers are used more than once.

3.6 Summary

3.6.1 Summary and Review

Summary

Dynamic routing protocols are used by routers to automatically learn about remote networks from other routers.
In this chapter you were introduced to several different dynamic routing protocols.

You learned that routing protocols can be classified as either classful or classless, either distance vector, link-
state, or path vector, and whether a routing protocol is an interior gateway protocol or an exterior gateway
protocol. The differences in these classifications will become better understood as you learn more about these
routing concepts and protocols in later chapters.

Routing protocols not only discover remote networks, but also have a procedure for maintaining accurate
network information. When there is a change in the topology it is the function of the routing protocol to inform
other routers about this change.

When there is a change in the network topology, some routing protocols can propagate that information
throughout the routing domain faster than other routing protocols. The process of bringing all routing tables to a
state of consistency is called convergence. Convergence is when all of the routers in the same routing domain or
area have complete and accurate information about the network.

Metrics are used by routing protocols to determine the best path or shortest path to reach a destination network.
Different routing protocols may use different metrics. Typically, a lower metric means a better path. Five hops
to reach a network is better than 10 hops.
Routers sometimes learn about multiple routes to the same network from both static routes and dynamic routing
protocols. When a router learns about a destination network from more than one routing source, Cisco routers
use the administrative distance value to determine which source to use. Each dynamic routing protocol has a
unique administrative value, along with static routes and directly connected networks. The lower the
administrative value, the more preferred the route source. A directly connected network is always the preferred
source, followed by static routes and then various dynamic routing protocols.

All of the classifications and concepts in this chapter will be discussed more thoroughly in the rest of the
chapters of this course. At the end of this course you may wish to review this chapter to get a review and
overview of this information.