30RB/30RQ

Pro-Dialog Control

A B C
R

Operation and maintenance instructions

 Contents

1 - SAFETY CONSIDERATIONS................................................................................................................................................ 3
1.1 - General....................................................................................................................................................................................... 3
1.2 - Avoid electrocution................................................................................................................................................................... 3
2 - GENERAL DESCRIPTION..................................................................................................................................................... 3
2.1 - General....................................................................................................................................................................................... 3
2.2 - Abbreviations used................................................................................................................................................................... 3
3 - HARDWARE DESCRIPTION................................................................................................................................................ 4
3.1 - General....................................................................................................................................................................................... 4
3.2 - Electrical supply to boards....................................................................................................................................................... 4
3.3 - Light emitting diodes on boards.............................................................................................................................................. 4
3.4 - The sensors................................................................................................................................................................................. 4
3.5 - The controls................................................................................................................................................................................ 5
3.6 - Connections at the user’s terminal block............................................................................................................................... 5
4 - SETTING UP PRO-DIALOG PLUS CONTROL................................................................................................................ 7
4.1 - User interface general features................................................................................................................................................ 7
4.2 - Unit start/stop control.............................................................................................................................................................. 8
4.3 - Menus......................................................................................................................................................................................... 9
5 - PRO-DIALOG PLUS CONTROL OPERATION............................................................................................................. 28
5.1 - Start/stop control..................................................................................................................................................................... 28
5.2 - Heating/cooling/standby operation....................................................................................................................................... 28
5.3 - Evaporator water pump control............................................................................................................................................ 29
5.4 - Control interlock contact....................................................................................................................................................... 29
5.5 - Evaporator antifreeze protection.......................................................................................................................................... 29
5.6 - Control point........................................................................................................................................................................... 29
5.7 - Demand limit........................................................................................................................................................................... 31
5.8 - Night mode............................................................................................................................................................................... 31
5.9 - Capacity control...................................................................................................................................................................... 31
5.10 - Head pressure control.......................................................................................................................................................... 31
5.11 - Defrost function.................................................................................................................................................................... 31
5.12 - Additional electric heater stage control............................................................................................................................. 31
5.13 - Control of a boiler................................................................................................................................................................. 31
5.14 - Master/slave assembly.......................................................................................................................................................... 31
5.15 - Optional heat reclaim module............................................................................................................................................. 32
5.16 - Free-cooling option............................................................................................................................................................... 32
6 - DIAGNOSTICS - TROUBLESHOOTING.......................................................................................................................... 33
6.1 - General..................................................................................................................................................................................... 33
6.2 - Displaying alarms.................................................................................................................................................................... 33
6.3 - Resetting alarms...................................................................................................................................................................... 33
6.4 - Alarm codes............................................................................................................................................................................. 34

GENERAL LEGEND

Each of the following drawings is replaced in the whole document by the corresponding explanation:
Start/stop button
Return key
Down arrow
Up arrow
DELTA T. Example: temperature difference between entering and leaving heat exchanger temperatures
Means character is flashing

The cover graphics are solely for illustration and forms no part of any offer for sale or any sale contract. The manufacturer
reserves the right to change the design at any time without notice.

2
1 - SAFETY CONSIDERATIONS 2 - GENERAL DESCRIPTION

1.1 - General 2.1 - General

Installation, start-up and servicing of equipment can be Pro-Dialog is a system for controlling single-, dual- or triple-
hazardous if certain factors particular to the installation are circuit 30RB air-cooled liquid chillers or 30RQ air-to-water
not considered: operating pressures, presence of electrical heat pumps. Pro-Dialog controls compressor start-up needed
components and voltages and the installation site (elevated to maintain the desired heat exchanger entering or leaving
plinths and built-up up structures). Only properly qualified water temperature. In cooling mode it controls the operation
installation engineers and highly qualified installers and of the fans to maintain the correct condensing pressure in
technicians, fully trained for the product, are authorised to each circuit. For heat pump units it controls and optimises
install and start-up the equipment safely. During all servicing the defrost cycles of each circuit in order to minimize the
operations all instructions and recommendations which heating capacity reduction. Safety devices are constantly
appear in the installation and service instructions for the monitored by Pro-Dialog to ensure their safe operation.
product, as well as on tags and labels fixed to the equipment Pro-Dialog also gives access to a Quick Test program
and components and accompanying parts supplied sepa- covering all inputs and outputs.
rately, must be read, understood and followed.
• Apply all standard safety codes and practices. All Pro-Dialog Plus controls can work in accordance with
• Wear safety glasses and gloves. three independent modes:
• Use the proper tools to move heavy objects. Move • Local mode: the machine is controlled by commands
units carefully and set them down gently. from the user interface.
• Remote mode: the machine is controlled by remote
1.2 - Avoid electrocution contacts (volt-free contacts).
• CCN mode: the machine is controlled by commands
Only personnel qualified in accordance with IEC (Inter- from the Carrier Comfort Network (CCN). In this
national Electrotechnical Commission) recommendations case, a data communication cable is used to connect
may be permitted access to electrical components. It is the unit to the CCN communication bus.
particularly recommended that all sources of electricity to
the unit be shut off before any work is begun. Shut off the The operating mode must be chosen with the Start/Stop
main power supply at the main circuit breaker or isolator. button described in section 4.2.1. When the Pro-Dialog
Plus system operates autonomously (Local or Remote
IMPORTANT: This equipment uses and emits electro- mode) it retains all of its own control capabilities but does
magnetic signals. Tests have shown that the equipment not offer any of the features of the CCN network.
conforms to all applicable codes with respect to electro-
magnetic compatibility. 2.2 - Abbreviations used

RISK OF ELECTROCUTION: Even when the main In this manual, the refrigeration circuits are called circuit
circuit breaker or isolator is switched off, certain circuits A, circuit B and circuit C. The compressors in circuit A are
may still be energised, since they may be connected to a labelled A1, A2, A3 and A4. Those in circuit B are B1, B2,
separate power source. B3 and B4 and those in circuit C are C1, C2, C3 and C4.

RISK OF BURNS: Electrical currents cause components The following abbreviations are used frequently:
to get hot either temporarily or permanently. Handle CCN : Carrier Comfort Network
power cable, electrical cables and conduits, terminal box CCn : Operating type: CCN
covers and motor frames with great care. LED : Light Emitting Diode
LEN : Sensor Bus (internal communication bus linking
Fan start-up: the basic board to the slave boards)
ATTENTION: In accordance with the operating LOFF : Operating type: Local Off
conditions the fans can be cleaned periodically. A fan can L-On : Operating type: Local On mode
start at any time, even if the unit has been shut down. L-Sc : Operating type: Local On following a time schedule
MASt : Operating type: master unit (master/slave assembly)
rEM : Operating type: by remote contacts
SCT : Saturated Condensing Temperature
SST : Saturated Suction Temperature
EXV : Electronic Expansion Valve

3
3 - HARDWARE DESCRIPTION 3.2 - Electrical supply to boards

3.1 - General All boards are supplied from a common 24 V a.c. supply
referred to earth.
Figure 1 - control board
CAUTION: Maintain the correct polarity when connecting
1 2 3 the power supply to the boards, otherwise the boards may
4
1 be damaged.

In the event of a power supply interrupt, the unit restarts

automatically without the need for an external command.
However, any faults active when the supply is interrupted
5 are saved and may in certain cases prevent a circuit or unit
from restarting.

3.3 - Light emitting diodes on boards

All boards continuously check and indicate the proper

operation of their electronic circuits. A light emitting diode
(LED) lights on each board when it is operating properly.
• The red LED flashing for a 2 second period on the
7 6 NRCP-BASE board indicates correct operation. A
Legend different rate indicates a board or a software failure.
1 CCN connector • The green LED flashes continuously on all boards to
2 Red LED, status of the board
3 Green LED, communication bus LEN
show that the board is communicating correctly over its
4 Orange LED, communication bus CCN internal bus. If the LED is not flashing, this indicates a
5 PD5 basic board LEN bus wiring problem.
6 Remote customer control connection contacts
7 Master board customer connection relay outputs • The orange LED of the master board flashes during
any communication via the CCN bus.
The control system consists of a PD5-BASE board, SPM
boards for compressor control, PD-AUX boards for fan 3.4 - The sensors
control, and an NRCP2-BASE board for units equipped with
energy management option or heat reclaim option. All Pressure sensors
boards communicate via an internal LEN bus. The PD5- Two types of electronic sensors are used to measure the
BASE boards continuously manage the information suction and discharge pressure in each circuit.
received from the various pressure and temperature probes,
and incorporates the program that controls the unit. Thermistors
The evaporator water sensors are installed in the entering
The user interface consists of two display blocks with up to and leaving side. The outdoor temperature sensor is mounted
26 LEDs and 16 buttons (according to unit type). It is below the control box. An optional water system tempera-
connected to the main basic board and gives access to a ture sensor can be used for master/slave assembly control
full array of control parameters. (in the case of leaving water control).

In heat pump units a sensor placed on an air heat exchanger

pipe ensures defrost operation.

4
3.5 - The controls 3.6 - Connections at the user’s terminal block

Evaporator pumps 3.6.1 - General description

The controller can regulate one or two evaporator pumps The contacts below are available at the user’s terminal block
and takes care of automatic change-over between pumps. on the PD5-BASE board (see figure 1). Some of them can
only be used if the unit operates in remote operating type
Evaporator heater (rEM). The following table summarises the connections at
It protects the evaporator (and the pipe heater for units the user’s terminal block.
without pump) against freezing if the unit is off.

Boiler
This relay output authorises start/stop of a boiler.

Cooling units
Description Connector/ Terminal Board Remarks
channel
Evaporator pump 1 control J2A / CH19 PD5-BASE The control can regulate one or two evaporator pumps, and automatically change over
between the two pumps.
Evaporator pump 2 control J2A / CH20 PD5-BASE The control can regulate one or two evaporator pumps, and automatically change over
between the two pumps.
Evaporator heater control J2B / CH21 PD5-BASE This (and the pipe heater for units without pumps) protects the evaporator against frost.
Alarm relay output J3 / CH24 PD5-BASE Indicates alarms.
Alert relay output J3 / CH25 PD5-BASE Indicates alerts.
Operation or ready-to-start relay J3 / CH26 PD5-BASE Indicates if the unit is ready to start or operates.
output
Contact 1: J4 / CH11 32-33 PD5-BASE This contact is used for unit start/stop. It is only taken into account if the unit is under
Start/stop remote operation control (rEM).
Contact 2: J4 / CH12 65-66 PD5-BASE This contact is only taken into account if the unit is under remote operation control (rEM).
Setpoint selection
Contact 3: J4 / CH13 63-64 PD5-BASE See the description of these contacts in sections 3.6.5 and 3.6.6.
Demand limit selection 1
Contact 3 bis: CH9 NRCP2-BASE This contact is only present if the energy management option is used.
Demand limit selection 2
User safety loop input J4 / CH15a 34-35 PD5-BASE This contact is mounted in series with the water flow control contact. It can be used for
any customer safety loop that requires that the unit is stopped, if it is open. If it is unused
this contact must be bridged.
Contact 4: J4 / CH14 PD5-BASE This contact is used to select the heat reclaim mode.This contact is only used, if the heat
Heat reclaim selection reclaim option is used (not compatible with the free cooling option).
Contact 4: J4 / CH14 PD5-BASE If this contact is closed, it is used to prevent operation of the free cooling mode. It is only
Free cooling prevention taken into account, if the unit is under remote operation control (rEM). This contact is only
used if the free cooling option is used (incompatible with the heat reclaim option).
Contact 5: J5C / CH18 PD5-BASE If this contact is open, the pump is controlled and an alarm has tripped.
Pump operation status
Connection to CCN J12 PD5-BASE An RS-485 bus is used for connection to the CCN.
- Pin 1: signal +
- Pin 2: ground
- Pin 3: signal -
Critical alarm relay output J2C / CH23 PD5-BASE Output allows disconnecting the general unit power supply, if a contactor is stuck and
there is an increased risk of the unit being damaged.

5
Heat pump units
Description Connector/ Terminal Board Remarks
channel
Evaporator pump 1 control J2A / CH19 PD5-BASE The control can regulate one or two evaporator pumps, and automatically change over
between the two pumps.
Evaporator pump 2 control J2A / CH20 PD5-BASE The control can regulate one or two evaporator pumps, and automatically change over
between the two pumps.
Evaporator heater control J2B / CH21 PD5-BASE This (and the pipe heater for units without pumps) protects the evaporator against frost.
4-way valve A control J2C/ CH22 PD5-BASE The control regulates the 4-way valve during heat/cool changeover or during defrost
cycles.
4-way valve B control J2C/ CH23 PD5-BASE The control regulates the 4-way valve during heat/cool changeover or during defrost
cycles.
Alarm relay output J3 / CH24 PD5-BASE Indicates alarms.
Alert relay output J3 / CH25 PD5-BASE Indicates alerts.
Operation or ready-to-start relay J3 / CH26 PD5-BASE Indicates if the unit is ready to start or operates.
output
Contact 1: J4 / CH11 32-33 PD5-BASE This contact is used for unit start/stop. It is only taken into account if the unit is under
Start/stop remote operation control (rEM).
Contact 2: J4 / CH12 65-66 PD5-BASE This contact is only taken into account if the unit is under remote operation control (rEM).
Setpoint selection
Contact 3: J4 / CH13 63-64 PD5-BASE See the description of these contacts in sections 3.6.5 and 3.6.6.
Demand limit selection 1
Contact 3 bis: CH9 NRCP2-BASE This contact is only present if the energy management option is used.
Demand limit selection 2
User safety loop input J4 / CH15a 34-35 PD5-BASE This contact is mounted in series with the water flow control contact. It can be used for
any customer safety loop that requires that the unit is stopped, if it is open. If it is unused
this contact must be bridged.
Contact 4: J5B / CH17 PD5-BASE This contact is used for heating/cooling mode selection. It is only taken into account if the
Heating/cooling selection unit is under remote operation control (rEM).
Contact 5: J5C / CH18 PD5-BASE If this contact is open, the pump is controlled and an alarm has tripped.
Pump operation status
Connection to CCN J12 PD5-BASE An RS-485 bus is used for connection to the CCN.
- Pin 1: signal +
- Pin 2: ground
- Pin 3: signal -
Critical alarm relay output J2C / CH22 NRCP2-BASE Output allows disconnecting the general unit power supply, if a contactor is stuck and
there is an increased risk of the unit being damaged (available if the energy management
option is used).

3.6.2 - Volt-free contact on/off/cooling/heating without 3.6.4 - Volt-free setpoint selection

multiplexing This volt-free contact permits changing the setpoint. The
If the automatic heating/cooling changeover function is setpoints can be modified in the setpoint menu.
not selected (see section 5.2) and if the user configuration
allows this (heat pump and Pro-Dialog interface selection) Cooling Heating
the operation of contacts 1 and 4 is as follows: CSP 1 CSP2 Auto HSP1 HSP2 Auto
Contact 2 Open Closed - Open Closed -

OFF ON cooling ON heating

Contact 1 Open Closed Closed
3.6.5 - Volt-free demand limit contact with energy
Contact 4 - Open Closed management option
Contact status not significant For units with the energy management option the demand
limit contact 3 is located on the PD5-BASE board and
3.6.3 - Volt-free contact on/off/cooling/heating with contact 3 bis is on the NRP2-BASE board. Demand limit is
multiplexing now multiplexed.
If the automatic heating/cooling changeover function is
selected (see section 5.2) and if the user configuration Capacity
allows this (heat pump and Pro-Dialog interface selection) 100% limit 1 limit 2 limit 3
the operation of contacts 1 and 4 is multiplexed: Contact 3 Open Closed Open Closed
Contact 3 bis Open Open Closed Closed

OFF ON cooling ON heating ON auto

Contact 1 Open Closed Closed Open
3.6.6 - Volt-free demand limit contact without energy
Contact 4 Open Open Closed Closed management option
For units without energy management option, contact 3 is
NOTE: The automatic changeover function (ON auto) located on the PD5-BASE board.
selects the cooling or heating mode based on the outdoor
temperature (see section 5.2). Capacity
100% limit 1
Contact 3 Open Closed

6
4 - SETTING UP PRO-DIALOG PLUS CONTROL

4.1 - User interface general features

dual-circuit chiller interface Dual-circuit heat pump interface
Main interface summary interface Main interface summary interface

A B A B
R

A B
A B

Menu block Menu block

triple-circuit chiller interface
Main interface Summary interface The local interface enables a number of operating para-
meters to be displayed and modified. The interface consists
of two distinct parts: the main interface (left hand section)
A B C
and the summary interface (right hand section).
R

Main interface
A
It gives access to all Pro-Dialog Plus data and operating
B
functions. It consists of:
C
• A two-digit display showing the number of the item
selected.
• A four-digit display showing the contents of the item
selected.
• LEDs and buttons for unit start/stop, menu selection,
Menu block menu item selection and value adjustment.
Main interface
Button Name Description
Menu Permits the selection of a main menu. Each main menu is represented by an icon. The icon is lit if active.

Up arrow Permits scrolling through the menu items (in the two-digit display). If the modification mode is active this button authorises increase of the
value of any parameter.
Down arrow Permits scrolling through the menu items (in the two-digit display). If the modification mode is active this button authorises decrease of the
value of any parameter.
Enter Gives access to the modification mode, validates a modification or displays expanded item description.

Start/stop Authorises start or stop of the chiller in local mode or modification of its operating type.

Main interface menu LEDs

LED Name Description
INFORMATION menu Displays the general operating parameters for the unit.

TEMPERATURES menu Displays the unit operating temperatures.

PRESSURES menu Displays the unit operating pressures.

SETPOINTS menu Displays the unit setpoints and enables them to be modified.

INPUTS menu Displays the status of the unit digital and analogue inputs.

OUTPUTS/TESTS menu Displays the status of the unit outputs and enables them to be tested.

CONFIGURATIONS menu Displays the unit configuration and enables it to be modified.

ALARMS menu Displays active alarms.

ALARMS HISTORY menu Displays the history of the alarms.

OPERATING LOG menu Displays the operating times and number of starts for the unit and the compressors.

7
The summary interface (right hand section) includes a mimic 4.2 - Unit start/stop control
diagram of the unit, together with push-buttons and LEDs.
It gives quick access to the main operating parameters of 4.2.1 - Description
the unit. The unit start/stop can be controlled by one of the following
methods:
Summary interface LEDs • Locally on the actual unit (Local control type)
LED Indication when lit • By remote control with the aid of user contacts (remote
Green LED:
The unit is authorised to start or is already running control type)
A Red LED: • By CCN control with the aid of the CCN (CCN control
- Lit: circuit A or unit shut down by alarm type)
- Flashing: circuit A or unit running with alarm present
B Red LED:
- Lit: circuit B or unit shut down by alarm The main interface includes a Start/Stop button which can
- Flashing: circuit B or unit running with alarm present
be used to stop or start the unit in the local operating type
C Red LED:
- Lit: circuit C or unit shut down by alarm or to select the remote or CCN operating type.
- Flashing: circuit C or unit running with alarm present
Green LED:
The evaporator pump is running.
The available operating types are described in the following
Yellow LEDs: table.
From top to bottom - start/stop status of compressor A1, A2, A3 and A4
or B1, B2, B3 and B4 or C1, C2, C3 and C4. Flashing LED indicates that
the circuit is in the protection or defrost mode (A, B or C). The following operating types can be selected using the
Green LED: Start/Stop button:
The unit operates in heating mode.
Green LED:
Operating types
The unit operates in cooling mode.
4-digit Description
display
Summary interface push buttons (dual-circuit)
LOFF Local Off. The unit is halted in local mode.
Button Display
L-On Local On. The unit is in local control mode and is authorised to start.
Blue button: evaporator leaving or entering water temperature in °C
Gray button: outdoor air temperature in °C L-Sc* Local On - timer control. The unit is in local control mode. It is
authorised to start if the period is occupied. If the timer program for
Control point (setpoint + reset) in °C unit operation is unoccupied, the unit remains shut down until the
period becomes occupied.
CCN CCN. The unit is controlled by CCN commands.
Press 1: circuit A/B discharge pressure in kPa rEM Remote. The unit is controlled by remote control contacts.
(1) Press 2: circuit A/B saturated condensing temperature in °C MAST* Master Unit. The unit runs as a master in a two unit lead/lag
arrange-ment. This is displayed if the unit is configured for master/
Press 1: circuit A/B suction pressure in kPa
slave control.
(1) Press 2: circuit A/B saturated suction temperature in °C
* Displayed if the configuration requires it.
Press 1: compressor A1/B1 operating hours in h/10 or h/100 Section 5.1 gives a more detailed description of the commands to start/stop
(1) Press 2: compressor A2/B2 operating hours in h/10 or h/100 the unit, analysed by operating type.
Press 3: compressor A3/B3 operating hours in h/10 or h/100
Press 4: compressor A4/B4 operating hours in h/10 or h/100
(1) There is a separate button for each of the two circuits. 4.2.2 - Stopping the unit in local mode
The unit can be stopped in local mode at any time by
Summary interface push buttons (triple-circuit) pressing the Start/Stop button.
Button Display
Blue button: evaporator leaving or entering water temperature in °C To stop the unit
Gray button: outdoor air temperature in °C
Button Action 2-digit display 4-digit display
Control point (setpoint + reset) in °C Press the Start/Stop button for C LOFF
less than 4 seconds (one short
press is enough).
Press 1: circuit A/B/C discharge pressure in kPa If the button is released, the unit t LOFF
(1) Press 2: circuit A/B/C saturated condensing temperature in °C stops without the need for further
action.
Press 1: circuit A/B/C suction pressure in kPa
(1) Press 2: circuit A/B/C saturated suction temperature in °C
4.2.3 - Starting unit and selecting an operating type
Press 1: compressor A1/B1/C1 operating hours in h/10 or h/100
(1) Press 2: compressor A2/B2/C2 operating hours in h/10 or h/100 The unit can be started in local mode, or unit operating
Press 3: compressor A3/B3/C3 operating hours in h/10 or h/100 type can be changed at any time using the Start/Stop
Press 4: compressor A4/B4/C4 operating hours in h/10 or h/100
button. In the example that follows, the unit is stopped
Press 1: Selects circuit A to display information
A (only on triple-circuit units) (LOFF) and the user wants to start the unit in local mode.
Press 1: Selects circuit B to display information
B
A (only on triple-circuit units)
Press 1: Selects circuit C to display information
C
A (only on triple-circuit units)
(1) There is a common button for the three circuits; for circuit selection press one
of the three last buttons described above.

8
Start-up with the previously used operating type when the unit is stopped The following example shows how to access item 3 in the
in local mode (loff)
Pressures menu.
Button Action 2-digit 4-digit
display display
The unit is in local stop mode. The previously LOFF Selecting a menu item
used operating type is local on (L-ON) Operation Press Menu LED Item number
button 2-digit display
Press the Start/Stop button for 4 seconds (one L-On
short press-down is sufficient). L-ON Press the MENU button until 0
illuminates immediately. “C” flashes in the the LED marked PRESSURE
2-digit display to show that the controller is lights.
awaiting confirmation. 0
Press the Enter button to confirm the operating L-On
type. “t” is displayed in the 2-digit display to
Press one of the Arrow buttons 1
indicate the operating type selected. If the
until the two-digit display shows
Enter button is not pressed soon enough, the
3 (item number 3).
controller will cancel the change and remain in
2
the stop mode.

Changing the operating type 3

Button Action 2-digit 4-digit
display display
Continually press the operating type selection C LOFF 4.3.3 - Modifying the value of a parameter/access to a sub-
button for more than 4 seconds. menu
Hold down the Start/Stop button. L-On
The available operating types are displayed L-Sc
Press the Enter button for more than 2 seconds to enter the
one by one until the button is released. modification mode or to select a sub-menu. This lets you
correct the value of an item or select a sub-menu with the
aid of the up and down Arrow buttons (if you are authorised
rEM to overwrite the item concerned). When modification mode
Release the Start/Stop button if the operating
type you want is displayed (in this example
is activated, the LED for the main menu to which the item
L-On). “C” flashes in the 2-digit display to show belongs as well as the 2-digit display flash in the menu block.
that the controller is awaiting confirmation. Once the required value is obtained, press the Enter button
Press the Enter button to confirm the operating t L-On
type selected (in this example: L-On). “t” is again to validate the change or to access the sub-menu. The
displayed in the 2-digit display to indicate the LED for the menu to which the item and the 2-digit display
operating type selected. If the Enter button is
not pressed soon enough, the controller will
belong then stops flashing, indicating that modification
cancel the change and continue to use the mode no longer applies.
previous operating type.

In modification mode, the value to be modified increases

4.3 - Menus or decreases in steps of 0.1 every time you press the Arrow
buttons. Holding one of these buttons down increases the
4.3.1 - Selecting a menu rate of increase or decrease.
The MENU button authorises you to select a menu from
the 10 main menus that are available. Each time you press NOTE: The access to a sub-menu may require entering a
this button one of the 10 LEDs lights up in turn alongside password. This is automatically requested. See section
each of the icons representing a main menu. The active 4.3.11.2.
menu is the one against which the LED is lit. If a menu is
empty then its LED is not lit. To scroll quickly through the The following example shows how to modify the value of
menus, hold the MENU button down. item 1 in the Setpoint menu.
4.3.2 - Selecting a menu item
The up and down Arrow buttons let you scroll through the
menu items. Menu item numbers are displayed in the two-
digit display. The item number increases or decreases every
time you press the up or down Arrow button. The menu
items that are not in use or incompatible with the configu-
ration are not displayed. The value or status associated
with the active item is displayed in the four-digit display.
To scroll quickly through the items, hold the up or down
Arrow button down.

9
4.3.4 - Expand display
Pressing the Enter button causes a 23 character text expan-
sion to be scrolled across the four-digit display. All user
menus provide an expansion of the current displayed
parameters. If the expansion is complete the four-digit
display reverts to item value. This function can be inhibited
through the User Configuration menu.

Modifying the value of a parameter

Operation value Press button Menu LED Item number Item 4-digit
2-digit display display
Hold on the MENU button until the LED for SETPOINT lights. 0

Press one of the Arrow buttons until the two-digit display shows 1 (item number 1- cooling setpoint 2). 1 6.0
The value for setpoint 2 is displayed in the four-digit display (6.0°C in this example).

Press the Enter button for more than 2 seconds to enable the value associated with item 1 to be 6.0
modified. The Setpoint menu LED and the two-digit display flash indicating that modification mode is 1
active.
Keep pressing the Down Arrow button until the value 5.7 is displayed in the four-digit display. The 5.9
Setpoint menu LED and the two-digit display keep flashing. 1

1 5.8

1 5.7
Press the Enter button again to validate the change. The new setpoint is 5.7°C.The Setpoint menu 1 5.7
LED and the two-digit display stop flashing, indicating that modification mode no longer applies.

10
 MAIN MENUS

INFORMATIONS
INFORMATION TEMPERATURES
TEMPERATURES PRESSION S
PRESSURES CONSIGNES
SETPOINTS ENTREES
INPUTS SORTIES
OUTPUTS CONFIGURATION
CONFIGURATION ALARMES
ALARMS HISTORIQUE ALARMES
ALARM HISTORY ALARMES
RUNTIME

SUB-MENUS

OUTPUT 1 OUTPUT 2 USER SERVICE FACTORY RUNTIME 1 RUNTIME 2 RUNTIME 3 MAINTENANCE

SUB-SUB-MENUS

USER
USER 11 USER
USER 22 TIME & DATE
TIME & DATE SCHEDULE
SCHEDULE 11 SCHEDULE
SCHEDULE 22 HOLIDAY
HOLIDAYS BROADCAST SERVICE
SERVICE11 SERVICE2
SERVICE 2 MASTER/SLAVE
MASTER/SLAVE HSM
HSM

PERIOD 1 PERIOD 1 HOLIDAY 1

PERIOD 2 PERIOD 2 HOLIDAY 2

PERIOD 3 PERIOD 3 HOLIDAY 3

SUB-SUB-SUB-MENUS PERIOD 4 PERIOD 4 HOLIDAY 4

PERIOD 5 PERIOD 5 HOLIDAY 5

PERIOD 6 PERIOD 6 HOLIDAY 6

PERIOD 7 PERIOD 7 HOLIDAY 7

Menu structure

PERIOD 8 PERIOD 8 HOLIDAY 8

HOLIDAY 16

11
12
ITEM STATUS TEMP PRESSURES SETPOINTS INPUTS OUTPUTS CONFIG ALARMS ALARMS HISTORY RUNTIMES
0 Default display Evaporator water Discharge Cooling setpoint 1 Contact 1: on/off/heating/ Output 1 SUB-MENU: User Number of active Historic alarm code 1** SUB-MENU:
entering temp. pressure circuit A cooling Configuration (USEr) alarms/resets** Runtimes 1
1 Mode Evaporator water Suction pressure Cooling setpoint 2 Contact 2: setpoint selection Output 2 SUB-MENU: Service Active alarm code 1** Historic alarm code 2** SUB-MENU:
leaving temp. circuit A Configuration Runtimes 2
(SErviCE)
2 Chiller occupied mode* Outdoor temperature Discharge Ice storage setpoint* Contact 4: heating/cooling [1]* - SUB-MENU: Factory Active alarm code 2** Historic alarm code 3** SUB-MENU:
pressure circuit B* Configuration Runtimes 3
(FACtorY)
3 Minutes left Heat reclaim entering Suction pressure Heating setpoint 1* Contact 4: heat reclaim [2]* - - Active alarm code 3** Historic alarm code 4** SUB-MENU:
water temp.* circuit B* OR free cooling prevention [2] Maintenance
4 Cooling/heating Heat reclaim leaving Discharge Heating setpoint 2* User safety loop input status - - Active alarm code 4** Historic alarm code 5** -
selection* water temp.* pressure circuit C*
5 Cooling/heating status* Saturated discharge Suction pressure Auto changeover Water pump operation - - Active alarm code 5** Historic alarm code 6** -
temperature circuit A circuit C* threshold (cooling mode)* contact status*
6 Heat reclaim selection* Saturated suction Vacuum pressure, Auto changeover Control box thermostat - - - Historic alarm code 7** -
temp. circuit A circuit A* threshold (heating mode)*
7 Total capacity in % Suction temperature, Vacuum pressure, Heat reclaim mode input Contact 3: demand limit - - - Historic alarm code 8** -
circuit A circuit B* setpoint* selection 1*
8 Capacity circuit A in % Superheat, circuit A - Heat reclaim mode input Contact 3 bis: demand limit - - - Historic alarm code 9** -
dead band* selection 2*
9 Capacity circuit B in % Saturated discharge - Setpoint demand Ice storage remote contact* - - - Historic alarm code 10** -
temp. circuit B limitation 1*
10 Capacity circuit C in Saturated discharge - Setpoint demand Remote unit contact, - - - Historic alarm code 11** -
%* temp. circuit B limitation 2* continued occupied mode*
11 Present demand limit Suction temperature, - Setpoint demand User safety loop input* - - - Historic alarm code 12** -
in % circuit B limitation 3*
Menu tree structure

12 Present lag limit in %* Superheat, circuit B - Ramp loading* Demand limit control - - - Historic alarm code 13** -
limitation value*
13 Setpoint in local Saturated discharge - Cooling - zero reset Setpoint reset value* - - - Historic alarm code 14** -
control temp. circuit C* threshold*
14 Setpoint occupied Saturated discharge - Cooling - full reset Ambient temperature value* - - - Historic alarm code 15** -
mode temp. circuit C* threshold*
15 Active setpoint Suction temperature, - Cooling - full reset value* Subcooling liquid - - - Historic alarm code 16** -
circuit C* temperature, circuit A*
16 Control point Superheat, circuit C* - Heating - zero reset Subcooling liquid - - - Historic alarm code 17** -
threshold* temperature, circuit B*
17 Controlled water Defrost temperature, - Heating - full reset Subcooling temperature, - - - Historic alarm code 18** -
temperature circuit A* threshold* circuit A*
18 Indicator, heat recovery Defrost temperature, - Heating - full reset value* Subcooling temperature, - - - Historic alarm code 19** -
in progress, circuit A* circuit B* circuit B*
19 Indicator, heat recovery System water - - - - - - Historic alarm code 20** -
in progress, circuit B* temperature*
Legend
* Displayed if the configuration requires it 1 For heat pump units
** Displayed if the alarm exists 2 For cooling only units
- Not in use
4.3.5 - Description of the Information menu

Information menu (3)

Item Format Units Description
0 Automatic display mode. It cycles through the following displays:
±nn.n °C 1: Controlled water temperature: temperature of the water that the unit tries to maintain at the control point.

2: Unit operating type

LOFF - Local Off
L-On - Local On
L-Sc - Local On - based on unit clock. Displayed if the CCN/clock board is installed
CCn - CCN Control. Displayed if the CCN/clock board is installed
rEM - Remote Control
MASt - Master unit

3: Unit status
OFF - Off: Unit is stopped and not authorised to start.
rEADY - Ready: Unit is authorised to start
dELAY - Delay: Unit is in delay at start-up. This delay is active after the unit has been switched on. The delay can be configured in the
- User Configuration menu
StOPPing - Stopping: Unit is currently stopping
running - On: Unit is running or authorised to start
triPout - Fault shutdown
OvErridE - Limit: The operating conditions do not allow total unit operation
dEFrOSt - Defrost: One circuit is in defrost mode
FrEEcOOl Free cooling: The unit operates in free cooling mode

4. Unit occupied/unoccupied status

OCCUPIEd - Occupied: Unit in occupied mode
UNOCCUPIEd - Unoccupied: Unit in unoccupied mode

5. Heating/cooling operating mode

COOL - Cooling: Unit operates in cooling mode
HEAT - Heating: Unit operates in heating mode
StAndbY - Standby: Unit is in auto cooling/heating changeover mode, and is in standby
BotH - Both: The unit operates in cooling (compressors) and heating (boiler). Only with HSM operation

- 6: Alarm mode
ALArM - Alarm: Unit is totally stopped because of failure
ALErt Alert: Unit is in failure but not completely stopped

7: Master/Slave status
MAStEr - Master: The master/slave control is active and the unit is the master
SLAvE - Slave: The master/slave control is active and the unit is the slave
Texts 4 and 5 are not displayed if the unit is in Local off mode or if the unit is in remote control mode and contact 1 is open
1 [1] nn Active mode codes. Each active mode is displayed in turn. This Item is masked when nil. Pressing the enter button when a mode
- code is displayed causes a character text expansion to be scrolled accross the four-digit display. See the description in the
following table
2 [2] This item indicates the current unit occupied/unoccupied mode.
occu - Occupied
unoc Unoccupied
Forc The value is displayed in turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
3 nn.n minutes Start-up delay. This item indicates the minutes left before the unit can be started. This delay at start-up is always active after the
unit has been switched on. The delay can be configured in the User Configuration 1 menu.
4 [2] Heating/cooling on selection: This item is accessible in read/write, if the unit is in local control mode.
HEAt - Heating mode selection
COOL - Cooling mode selection
Auto - Automatic heating/cooling mode changeover selection. Only displayed if the auto changeover function is selected (User
- Configuration 1 menu).
5 [2] Heating/cooling mode. This item indicates whether the unit is in cooling or heating. Displayed if the unit controls a boiler.
HEAt - Heating
COOL - Cooling
StbY - Standby: Unit is in auto cooling/heating changeover mode, and is in standby.
both - Both: The unit operates in cooling (compressors) and heating (boiler). Only with HSM operation.
Forc - The value is displayed in turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
6 [2] Yes - Heat reclaim mode selection. Only displayed if the unit is a chiller and the heat reclaim option is used. The value is displayed in
No turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
Forc
6 [2] Yes - Free cooling prevention status. Only shown if the unit is a chiller and if the free cooling option is available. The value is displayed
No in turn with “Forc”, when the unit is in CCN control and if this variable is forced through CCN.
Forc
7 nnn % Total active capacity of unit. It is the percentage of compressor capacity used by the unit.
8 nnn % Total active capacity of circuit A. It is the percentage of compressor capacity used by on circuit A.
9 [2] nnn % Total active capacity of circuit B. It is the percentage of compressor capacity used by on circuit B. Dual-circuit units only.
10 [2] nnn % Total active capacity of circuit C. It is the percentage of compressor capacity used by on circuit C. Triple-circuit units only.
11 nnn % Present demand limit. This is the authorised operating capacity of the unit. See section 5.7.
Forc The value is displayed in turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
12 [2] nnn % Present lag chiller demand limit. Displayed when the master/slave control is selected.
13 [2] Setpoint select in local mode. This point is read/write accessible. Displayed only when the unit is LOFF, L-On or L-Sc operating type.
SP-1 - SP-1 = cooling/heating setpoint 1
SP-2 SP-2 = cooling/heating setpoint 2
AUtO AUtO = active setpoint depends on schedule 2 (setpoint selection schedule). See section 5.6.1 & 4.3.11.6.

13
Information menu (3) continued
Item Format Units Description
14 [2] Setpoint occupied mode.
occu - Occupied: cooling setpoint 1 is active
unoc Unoccupied: cooling setpoint 2 is active
Forc The value shall be displayed in turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
15 ±nn.n °C Active setpoint. This is the current cooling/heating setpoint: cooling/heating setpoints 1, 2 or ice storage setpoint.
16 Control point. This is the setpoint used by the controller to adjust the temperature of the leaving or entering water (according to
configuration).
±nn.n °C Control point = active setpoint + reset. See section 5.6
Forc The value is displayed in turn with ‘Forc’ when the unit is in CCN control and if this variable if forced through CCN.
17 ±nn.n °C Controlled water temperature. Water temperature that the unit tries to maintain at the control point.
18 n Heat reclaim sequence indicator, circuit A (option).
19 n Heat reclaim sequence indicator, circuit B (option).
[1] This item is masked when nil.
[2] This item is displayed in certain unit configurations only.

Description of operating modes (item 1 of the Information menu)

Mode # Mode name Description
1 Delay at start-up active The delay at start-up operates after the unit has been switched on. If the delay has not expired, the mode is
active. The delay is configured in the User Configuration 1 menu.
2 2nd cooling/heating setpoint active The second cooling/heating setpoint is active. See section 5.6.1
3 Setpoint reset active In this mode, the unit uses the reset function to adjust the leaving water temperature setpoint.
4 Demand limit active In this mode, the demand at which the unit is authorised to operate is limited.
5 Ramp loading active Ramp loading is active. This item is referenced to the allowed low and high temperature limits, controlled at the
water heat exchanger in order to prevent compressor overloading. Ramp function must be configured (see
User Configuration 1 menu). Ramp values can be modified (see Setpoint menu).
6 Water heat exchanger heater active The water heat exchanger heater is active.
7 Evaporator pump reversal in effect The unit is fitted with two evaporator water pumps and reversal between pumps is in effect.
8 Evaporator pump periodic start The unit is stopped and the pump is started each day at 14.00 p.m. for two seconds. This function needs to be
configured in the User Configuration 2 menu.
9 Night mode (low noise level) The night mode (low noise level) is active. The number of fans is reduced (if operating conditions allow) and
unit capacity can be limited.
10 Unit in SM control Unit is in control of a System Manager (FSM, CSM III or HSM).
11 Master/slave link active Unit is connected to a secondary unit by a master slave link and the master/slave modes are active.
12 Auto heating/cooling changeover active If the unit is in auto mode, the heating/cooling changeover is automatic, based on the outdoor temperature.
13 Free cooling mode active The free cooling mode is active.
14 Heat reclaim mode active The heat reclaim mode is active.
15 Electric heating stages active The electric heating stages are active.
16 Low water entering temperature protection The unit is in heating mode and compressor start is not authorised, as the entering water temperature is below 10°C.
in heating mode
17 Boiler active The unit controls a boiler and this is operating.
18 Ice storage mode active The unit operates in cooling mode and the ice storage mode is active.
19, 20 Defrost 19 = circuit A, 20 = circuit B. The unit is in heating mode, and the defrost sequence is active on the relevant circuit.
21, 22, 23 Low suction temperature protection 21 = circuit A, 22 = circuit B, 23 = circuit C. Protection for evaporator low suction temperature circuit is active. In
this mode, circuit capacity is not authorised to rise and the circuit can be unloaded.
24, 25, 26 Hot gas protection 24 = circuit A, 25 = circuit B, 26 = circuit C. Hot gas discharge protection is active. In this mode, the circuit
capacity cannot increase, and the circuit may be unloaded.
27, 28, 29 High pressure protection 27 = circuit A, 28 = circuit B, 29 = circuit C. The circuit is in high pressure protection mode because the HP
protection threshold has been exceeded. Circuit has been unloaded and the circuit capacity is not authorised
to rise.
30, 31, 32 Low superheat protection 30 = circuit A, 31 = circuit B, 32 = circuit C. The circuit is in the low superheat protection mode to prevent the
compressors drawing in liquid refrigerant.

14
4.3.6 - Description of the Temperatures menu

Temperatures menu [1]

Item Format Units Comments
0 ±nn.n °C Heat exchanger entering water temperature
1 ±nn.n °C Heat exchanger leaving water temperature
2 ±nn.n °C Outdoor temperature
3 [1] ±nn.n °C Heat reclaim entering water temperature (only if heat reclaim option is configured)
4 [1] ±nn.n °C Heat reclaim leaving water temperature (only if heat reclaim option is configured)
5 ±nn.n °C Saturated condensing temperature, circuit A
6 ±nn.n °C Saturated suction temperature, circuit A
7 ±nn.n °C Suction temperature, circuit A
8 ±nn.n °C Superheat temperature, circuit A
9 ±nn.n °C Saturated condensing temperature, circuit B
10 ±nn.n °C Saturated suction temperature, circuit B
11 ±nn.n °C Suction temperature, circuit B
12 ±nn.n °C Superheat temperature, circuit B
13 [1] ±nn.n °C Saturated condensing temperature, circuit C (displayed if circuit C exists)
14 [1] ±nn.n °C Saturated suction temperature, circuit C (displayed if circuit C exists)
15 [1] ±nn.n °C Suction temperature, circuit C (displayed if circuit C exists)
16 [1] ±nn.n °C Superheat temperature, circuit C (displayed if circuit C exists)
17,18 ±nn.n °C Defrost temperature (displayed if unit is in heat pump mode)
17 = circuit A, 18 = circuit B
19 [1] ±nn.n °C Chilled water system temperature. This item is only displayed when the master/slave option is configured.
[1] This item is displayed in certain unit configurations only

4.3.7 - Description of the Pressures menu

Pressures menu [1]

Item Format Units Comments
0 nnnn kPa Discharge pressure, circuit A. Relative pressure.
1 nnn kPa Suction pressure, circuit A. Relative pressure.
2 nnnn kPa Discharge pressure, circuit B. Relative pressure.
3 nnn kPa Suction pressure, circuit B. Relative pressure.
4 nnnn kPa Discharge pressure, circuit C. Relative pressure.
5 nnn kPa Suction pressure, circuit C. Relative pressure.
6 [1] ±nnn kPa Vacuum pressure, circuit A. Only displayed if heat reclaim option is used.
7 [1] ±nnn kPa Vacuum pressure, circuit B. Only displayed if heat reclaim option is used.
8 [1] nnn kPa Suction pressure, refrigerant pump, circuit A. Only displayed if the free cooling option is available.
9 [1] nnn kPa Discharge pressure, refrigerant pump, circuit A. Only displayed if the free cooling option is available.
10 [1] ±nnn kPa Differential pressure at the terminals of the refrigerant pump, circuit A. Only displayed if the free cooling option is available.
11 [1] nnn kPa Suction pressure, refrigerant pump, circuit B. Only displayed if the free cooling option is available.
12 [1] nnn kPa Discharge pressure, refrigerant pump, circuit B. Only displayed if the free cooling option is available.
13 [1] ±nnn kPa Differential pressure at the terminals of the refrigerant pump, circuit B. Only displayed if the free cooling option is available.
14 [1] nnn kPa Suction pressure, refrigerant pump, circuit C. Only displayed if the free cooling option is available.
15 [1] nnn kPa Discharge pressure, refrigerant pump, circuit C. Only displayed if the free cooling option is available.
16 [1] ±nnn kPa Differential pressure at the terminals of the refrigerant pump, circuit C. Only displayed if the free cooling option is available
[1] This item is displayed in certain unit configurations only.

15
4.3.8 - Description of the Setpoints menu

Setpoints menu [2]

Item Format Units Range Comments
0 ±nn.n °C -28 to 26 This item lets you modify Cooling setpoint 1.
1 ±nn.n °C -28 to 26 This item lets you modify Cooling setpoint 2.
2 [1] ±nn.n °C -28 to 0 This item lets you modify the ice storage setpoint.
3 [1] nnn °C 20 to 50 This item lets you modify Heating setpoint 1, only displayed for heat pumps.
4 nn.n °C 20 to 50 This item lets you modify Heating setpoint 2, only displayed for heat pumps.
5 [2] ±nn.n °C 3.8 to 50 Automatic changeover threshold, cooling mode. This item lets you display and modify the outdoor temperature
threshold at which the unit changes over in cooling mode. Displayed only if the auto cooling/heating changeover function is
selected.
6 [2] ±nn.n °C 0 to 46 Automatic changeover threshold, heating mode. This item lets you display and modify the outdoor temperature
threshold at which the unit changes over in heating mode. Displayed only if the auto cooling/heating changeover function is
selected and if the unit is a heat pump. The heating threshold must be 3.8°C below the cooling threshold, otherwise the new
setpoint will be rejected.
7 [2] nn.n °C 35 to 60 For the desuperheater option, this item permits control the minimum condensing temperature setpoint.
8 [2] nn.n °C 2.7 to 15 This item lets you display and modify the heat reclaim dead band.
9 nnn % 0 to 100 Demand limit 1 setpoint. Limitation by volt-free contact. This item is used to define the maximum capacity that the unit is
authorised to use, if the demand limit contact(s) activate limit 1. Contact control depends on the configuration.
10 [2] nnn % 0 to 100 Demand limit 2 setpoint. Limitation by volt-free contact. This item is used to define the maximum capacity that the unit is
authorised to use, if the demand limit contact(s) activate limit 2. Contact control depends on the configuration. Displayed
and used only for units with energy management option.
11 [2] nnn % 0 to 100 Demand limit 3 setpoint. Limitation by volt-free contact. This item is used to define the maximum capacity that the unit is
authorised to use, if the demand limit contact(s) activate limit 3. Contact control depends on the configuration. Displayed
and used only for units with energy management option.
12 [2] ±nn.n °C/min 0.1 to 1.1 Cooling ramp loading rate. This parameter is only accessible if the ramp function is validated in the User Configuration 1
menu. This item refers to the maximum permitted water heat exchanger low temperature rates (°C/min). When capacity
loading is effectively limited by the ramp, mode 7 is active.
13 [2] ±nn.n °C/min 0.1 to 1.1 Heating ramp loading rate. This parameter is only accessible if the ramp function is validated in the User Configuration 1
menu. This item refers to the maximum permitted water heat exchanger high temperature rates (°C/min). When capacity
loading is effectively limited by the ramp, mode 7 is active.
14 [2] ±nn.n [3] [3 bis] Zero reset threshold, cooling mode.
15 [4] ±nn.n [3] [3 bis] Full reset threshold, cooling mode.
16 [4] ±nn.n °C -16.6 to 16.6 Full reset value, cooling mode.
17 [4] ±nn.n [3] [3 bis] Zero reset threshold, heating mode.
18 [4] ±nn.n [3] [3 bis] Full reset threshold, heating mode.
19 [4] ±nn.n °C -16.6 to 16.6 Full reset value, heating mode.
[1] This item shall be masked when not used.
[2] This item is displayed in certain unit configurations only.
[2] Depends on the configuration of the reset type. If reset type is 1, 2 or 4 the unit is °C; if reset type is 3, the unit is mA.
[3 bis] The scale depends on the reset type selected.
[4] Depends on the value of items 9 or 10 of the user configuration menu 1.
If the reset type selection point
= 0: reset not selected
= 1: reset based on outside temperature
= 2: reset based on temperature difference
= 3: reset based on 4-20 mA control
= 4: reset based on room temperature

Reset thresholds in cooling or heating mode

Reset threshold Zero Full
Reset based on outdoor air temperature -10 to 51.6°C -10 to 51.6°C
Reset based on temperature difference 0 to 13.6 0 to 13.6
Reset based on 4-20 mA control 0 to 11.1 °C 0 to 11.1 °C
Reset based on room temperature -10 to 51.6°C -10 to 51.6°C

16
4.3.9 - Description of the Inputs menu

Inputs menu [1]

Item Format Units Comments
0 oPEn/CLoS - Remote contact 1 status (on/off switch).
If the auto cooling/heating changeover function is not selected (User Configuration 1), this contact is used to start and stop the unit. If
the auto cooling/heating changeover function is selected, this contact is multiplexed with contact 4 to permit starting and stopping the
unit and the selection of heating/cooling/auto. This contact is only valid, if the unit is in the remote operating control (rEM) mode.
1 oPEn/CLoS - Remote contact 2 status.
Status of remote contact 2. This contact permits the selection of a setpoint. This contact is only active if the unit is in the remote
operation type. See section 3.6.1 for the description of this contact and section 3.6.4 for the description of the setpoint selection function.
2 [1] oPEn/CLoS - Remote contact 4 status.
If the automatic cooling/heating changeover function is not selected (User Configuration 1) this contact is used for the selection of
the heating or cooling operating mode. If the automatic cooling/heating changeover function is selected, this contact is multiplexed
with contact 1 to permit the starting and stopping of the unit and the selection of heating/cooling auto. This contact is only valid, if the
unit is in the remote operation control (rEM) mode.
3 [1] oPEn/CLoS - Remote contact 4 status.
This item is only displayed on chillers.
If the heat reclaim option is available, this contact allows remote selection of heat reclaim.
If the free cooling option is available, this contact allows prevention of free cooling mode operation.
4 oPEn/CLoS - Status user safety contact or water flow control contact. If the contact is open, the unit stops.
5 [1] oPEn/CLoS - Contact status: pump operation status.
6 oPEn/CLoS - Control box thermostat contact or reverse rotation contact.
7 [1] oPEn/CLoS - Remote contact 3 status. This contact permits selection of a demand limit. It is located on board PD5-BASE.
8 [1] oPEn/CLoS - Remote contact 3 bis status. This contact is only used if the energy management option is used. It is multiplexed with contact 3 to
permit selection of one of three demand limits.
9 [1] oPEn/CLoS - Ice storage remote contact status. This contact is located on board NRCP2 of the energy management option. It is used during
unit occupied periods to permit selection of a setpoint or ice storage setpoint.
10 [1] oPEn/CLoS - Unit occupied continued remote contact status. This contact is only used on units with energy management option to maintain
the occupied mode.
11 [1] oPEn/CLoS - User safety loop input status. This contact is accessible on the energy management option board. It can be used for any customer
safety loop that requires unit shut-down if it is closed.
12 [1] nn.n mA Demand limit signal.
This contact is only displayed when the energy management option is selected. This contact permits changing the lowest value,
based on a linear interpolation from 0 to 100% depending on the input value.
13 [1] nn.n mA Setpoint reset signal.
14 [1] °C Room temperature value, only used if the energy management option is selected and the room temperature sensor is installed.
15 [1] °C Liquid subcooling temperature, circuit A. Only used if the heat reclaim option is selected.
16 [1] °C Liquid subcooling temperature, circuit B. Only used if the heat reclaim option is selected.
17 [1] °C Subcooling temperature, circuit A. Only used if the heat reclaim option is selected.
18 [1] °C Subcooling temperature, circuit B. Only used if the heat reclaim option is selected.
19 [1] oPEn/CLoS °C Heat reclaim condenser water flow control. Controls the heat reclaim condenser water circulation.
[1] This item is displayed in certain unit configurations only

17
4.3.10 - Description of the Outputs/Tests menu

4.3.10.1 - General
This menu displays the status of the controller outputs.
Moreover, when the machine is fully stopped (LOFF) the
outputs can be activated for manual tests (the access to the
tests is password controlled).

4.3.10.2 - Menu description

Main outputs menu

Item Format Units Description
0 OUtPUts 1 - This menu permits access to outputs menu 1.
1 OUtPUts 2 - This menu permits access to outputs menu 2.

Outputs status & Tests menu

Item Format Units Description
0 OUtPUts 1 Menu When selected this item authorises return to the previous menu.
1 - Circuit A compressors, command status
b1b2b3b4 b1 = compressor A1
b2 = compressor A2
b3 = compressor A3
b4 = compressor A4
tESt In test mode, the Arrow buttons display 0001, 0010, 0100 and 1000 in succession, so as to force the compressor
outputs in turn. During the test phase, power to the compressor is switched on for 10 seconds only. It is then not possible
to restart the compressor for a further 30 seconds. When the test is completed the following is displayed:
FAIL - Fail: displayed if the test has failed because the compressor was not started or run in reverse rotation.
Good - Good: displayed if test was successful
2 b1b2b3b4 - Circuit B compressor, command status
b1 = compressor B1
tESt b2 = compressor B2
FAIL b3 = compressor B3
Good b4 = compressor B4
In test mode... as above
3 b1b2b3b4 - Circuit C compressor, command status
b1 = compressor C1
tESt b2 = compressor C2
FAIL b3 = compressor C3
Good b4 = compressor C4
In test mode... as above
4 b1b2 4-way reversing cycle valve status. In test mode, the arrow keys successively display 01 and 10, in order to authorise
tESt the test for each valve in turn.
b1 = valve circuit A
b2 = valve circuit B
This item is only displayed for heat pump units.
5 b1b2 b3b4 Compressor heater status, circuit A
tESt b1 = compressor heater A1
b2 = compressor heater A2
b3 = compressor heater A3
b4 = compressor heater A4
In test mode, the Arrow buttons display 0001, 0010, 0100 and 1000 in succession, so as to force the compressor heater
outputs in turn.
6 b1b2 b3b4 Compressor heater status, circuit B
tESt b1 = compressor heater B1
b2 = compressor heater B2
b3 = compressor heater B3
b4 = compressor heater B4
In test mode, the Arrow buttons display 0001, 0010, 0100 and 1000 in succession, so as to force the compressor heater
outputs in turn.
7 b1b2 b3b4 Compressor heater status, circuit C
tESt b1 = compressor heater C1
b2 = compressor heater C2
b3 = compressor heater C3
b4 = compressor heater C4
In test mode, the Arrow buttons display 0001, 0010, 0100 and 1000 in succession, so as to force the compressor heater
outputs in turn.
8 0 to 6 Fan status, circuit A. Permits selection of the fan to be tested.
tESt 1 = fan A1
2 = fan A2
3 = fan A3
4 = fan A4
5 = fan A5
6 = fan A6
9 0 to 6 Fan status, circuit B. Permits selection of the fan to be tested.
tESt 1 = fan B1
2 = fan B2
3 = fan B3
4 = fan B4
5 = fan B5
6 = fan B6

18
Outputs status & Tests menu (continued)
Item Format Units Description
10 0 to 6 Fan status, circuit C. Permits selection of the fan to be tested.
tESt 1 = fan C1
2 = fan C2
3 = fan C3
4 = fan C4
5 = fan C5
6 = fan C6
11 b1b2b3b4 Alarm status
tESt b1 = alarm relay
b2 = alert relay
b3 = general alarm relay (present if energy management option is used)
b4 = critical alarm relay output. Caution: If this output is connected, its activation will disconnect the general unit power
supply.
12 nnn % EXV A position
tESt 0% = EXV closed; 100% = EXV open
In test mode this permits selection of the required position.
13 nnn % EXV B position
tESt 0% = EXV closed; 100% = EXV open
In test mode this permits selection of the required position.
14 nnn % EXV C position
tESt 0% = EXV closed; 100% = EXV open
In test mode this permits selection of the required position.
15 nnn % Fan speed, circuit A. Only displayed if a variable speed controller is selected in circuit A.
tESt In test mode, this permits selection of the required speed.
16 nnn % Fan speed, circuit B. Only displayed if a variable speed controller is selected in circuit B.
tESt In test mode, this permits selection of the required speed.
17 nnn % Fan speed, circuit C. Only displayed if a variable speed controller is selected in circuit C.
tESt In test mode, this permits selection of the required speed.
18 - Evaporator water pump #1 command status. Not displayed if the unit does not control a pump.
On On: pump is running
Stop Stop: pump is stopped
tESt Forc: this item is displayed only when the unit is stopped locally (LOFF). selecting this item authorises turning on the
FAIL pump with no delay and for an unlimited length of time. The pump will remain on until any button of the user interface is
Good pressed: it is then immediately stopped. If the unit is in CCN control, then the pump status is displayed in turn with “Forc” if
Forc the pump status if forced through CCN.
During the test phase, power to the pump is switched on for 10 seconds only. When the test is completed the following is
displayed:
- Fail: displayed if the test has failed because the pump was not started
- Good: displayed if the test was successful
19 On - Evaporator water pump #2 command status. Not displayed if the unit does not control a secondary pump.
OFF On: pump is running
tESt Stop: pump is stopped
FAIL Forc: this item is displayed only when the unit is stopped locally (LOFF). selecting this item authorises turning on the
Good pump with no delay and for an unlimited length of time. The pump will remain on until any button of the user interface is
Forc pressed: it is then immediately stopped. If the unit is in CCN control, then the pump status is displayed in turn with “Forc” if
the pump status if forced through CCN.
During the test phase, ...as above

Submenu outputs 2 (selection)

Item Format Units Description
0 OUtPUts 2 Menu When selected this item authorises return to the previous menu.
1 On Heat reclaim condenser pump status. Only displayed when the heat reclaim option is selected.
OFF Forc: This item is only displayed when the unit is in Local off (LOFF) mode. Selecting this item permits starting up the pump
Forc whithout delay and for an unlimited period. The pump stays on until any button on the user interface is pressed: it is then
tESt immediately stopped. If the unit is under CCN control, the pump status is displayed alternatively with ‘Forc’, if the status is
FAIL forced by CCN.
Good
2 b1b2 Heat exchanger heater status (b1) and heat reclaim condenser heater status (b2).
3 b1b2 b3 Hot gas bypass valve status. Only displayed if the hot gas bypass option is selected.
b1 = hot gas bypass valve, circuit A
b2 = hot gas bypass valve, circuit B
b3 = hot gas bypass valve, circuit C
4 nnn % Heat reclaim condenser water valve position. Only displayed if the heat reclaim option is selected.
tESt
5 b1b2 b3b4 Heat reclaim operation valve status, circuit A.
b1 = air condenser entering valve, circuit A
b2 = water condenser entering valve, circuit A
b3 = air condenser leaving valve, circuit A
b4 = water condenser leaving valve, circuit A
6 b1b2 b3b4 Heat reclaim operation valve status, circuit B.
b1 = air condenser entering valve, circuit B
b2 = water condenser entering valve, circuit B
b3 = air condenser leaving valve, circuit B
b4 = water condenser leaving valve, circuit B
7 0 to 4 Additional heating stage status.
tESt 1 = stage 1
2 = stage 2
3 = stage 3
4 = stage 4

19
Submenu outputs 2 (selection) (continued)
Item Format Units Description
8 On Boiler operating status.
OFF On: operating
tESt OFF: stopped
9 b1b2 b3 Free cooling 3-way valve status (only displayed when the free cooling option is selected).
b1 = 3-way valves, circuit A
b2 = 3-way valves, circuit B
b3 = 3-way valves, circuit C
0 corresponds to a closed valve (cooling position) and 1 corresponds to an open valve (free cooling position)
10 b1b2 b3 Free cooling refrigerant pump status (only displayed when the free cooling option is selected).
tESt b1 = pump, circuit A
b2 = pump, circuit B
b3 = pump, circuit C
11 nn.n Unit capacity 0-10 V signal value (10 V = 100 %). Only displayed if the energy management option is selected.
tESt
12 b1b2 Chiller operating status
b1 = ready (ready-to-start or in operation)
b2 = in operation
13 YES/no Used for local interface test only. Lights or flashes all LEDs and blocks, so as to check that they are working properly.

4.3.10.3 - Manual tests 4.3.11.2 - Password

This function allows the user to test the outputs individually, A password must be entered in order to access the test
if the machine is completely shut down (LOFF). To carry function or to modify a configuration. It is automatically
out a manual test use the arrow keys to access the output to requested, if necessary: ‘EntEr PASS’ is displayed on the
be tested and press the Enter key (longer than 2 seconds) 4-digit display and the configuration menu LED flashes,
to activate the modification mode. The password is auto- indicating that the modification mode is active. Press the
matically requested, if it has not previously been verified. arrow keys until the value ‘11’ is displayed on the 4-digit
The Outputs/Test LED on the user interface begins to flash. display. Press Enter to validate this. The configuration menu
Enter the desired test value and again press Enter to start LED stops flashing. If the password is correct, ‘Good’ is
the test. ‘TESt’ is displayed on the 4-digit display alternately displayed. If the password is incorrect, ‘PASS incorrEct’ is
with the value tested. The Outputs/Test LED stops flashing. displayed. The User password has a default value of 11.
Press the Enter key or an arrow key to stop the test.
This value can be modified through the Service configuration.
4.3.11 - Description of the Configuration menu The password can be entered if the unit is fully stopped,
otherwise ‘ACCES dEniEd’ (access denied) will be displayed
4.3.11.1 - General on the 4-digit display. The controller automatically deacti-
This menu can be used to display and modify all configura- vates the password after 5 minutes without activity (i.e. no
tions: Factory, Service and User. Only the User Configuration buttons pressed) or after powering up.
can be modified by the end-user. The Factory, Service and
master/slave configurations are not described in this
document. A configuration can only be modified if the unit
is fully stopped (LOFF).

The menus User 1 [USEr 1] and User 2 [USEr 2] are

password-protected. The other menus are directly accessible,
except if item 11 of the User 2 menu (password for all
configurations) has been validated.

20
Sub-menu user configuration
Item User 1 User 2 Date Schedule 1 Schedule 2 Holidays Broadcast
[USER1] [USER2] [dAtE] [ScHEduLE 1MEnu] [ScHEduLE 2 MEnu] [HOLidAy MEnu] [BrodCASt]
0 Return to previous menu Return to previous menu Return to previousReturn to previous Return to previous Return to previous menu Return to previous
menu menu menu menu
1 Selection of lead circuit Periodic pump start-up Hour SUB-MENU: SUB-MENU: SUB-MENU: Broadcast
Period 1 [PErIod 1] Period 1 [PErIod 1] Holidays 1 [HOLidAy 1] acknowledger selection
2 Load sequence selection Night mode - start hour Day of the week SUB-MENU: SUB-MENU: SUB-MENU: Broadcast activation
Period 2 [PErIod 2] Period 2 [PErIod 2] Holidays 2 [HOLidAy 2]
3 Ramp selection Night mode - end hour Day and month SUB-MENU: SUB-MENU: SUB-MENU: Outdoor temperature
Period 3 [PErIod 3] Period 3 [PErIod 3] Holidays 3 [HOLidAy 3] broadcast bus
4 Start-up delay Night mode maximum Year SUB-MENU: SUB-MENU: SUB-MENU: Outdoor temperature
demand Period 4 [PErIod 4] Period 4 [PErIod 4] Holidays 4 [HOLidAy 4] broadcast element
5 Water pump selection Number clock 1 Summertime SUB-MENU: SUB-MENU: SUB-MENU:
activation Period 5 [PErIod 5] Period 5 [PErIod 5] Holidays 5 [HOLidAy 5]
6 Water pump changover Number clock 2 Summertime start SUB-MENU: SUB-MENU: SUB-MENU:
delay month Period 6 [PErIod 6] Period 6 [PErIod 6] Holidays 6 [HOLidAy 6]
7 Pump shutdown in standby CCN element number Summertime start SUB-MENU: SUB-MENU: SUB-MENU:
mode day of the week Period 7 [PErIod 7] Period 7 [PErIod 7] Holidays 7 [HOLidAy 7]
8 Verification of the water flow CCN bus number Summertime start SUB-MENU: SUB-MENU: SUB-MENU:
rate if the pump has stopped week of the month Period 8 [PErIod 8] Period 8 [PErIod 8] Holidays 8 [HOLidAy 8]
9 Setpoint reset selection, Interface text language Summertime end SUB-MENU:
cooling mode month Holidays 9 [HOLidAy 9]
10 Setpoint reset selection, Extended display Summertime end SUB-MENU:
heating mode selection day of the week Holidays 10 [HOLidAy 10]
11 Automatic heating/cooling Password for all user Summertime end SUB-MENU:
changeover selection configurations week of the month Holidays 11 [HOLidAy 11]
12 Demand limit selection Software version number SUB-MENU:
Holidays 12 [HOLidAy 12]
13 Maximum demand limit Boiler activation SUB-MENU:
current value temperature threshold Holidays 13 [HOLidAy 13]
14 Minimum demand limit Ice storage mode SUB-MENU:
current value authorisation Holidays 14 [HOLidAy 14]
15 Electric heating stage Free cooling authorisation SUB-MENU:
operation threshold temperature limit (max.) Holidays 15 [HOLidAy 15]
16 Electric heating stage Authorisation of pre-cooling SUB-MENU:
operation schedule by free cooling Holidays 16 [HOLidAy 16]
17 Electric heating safety stage Maximum duration of full
threshold load operation in free
cooling
18 Quick start-up, electric
heater stages in defrost mode

NOTE: The items in brackets show what is displayed on

the user interface.

CONFIGURATION Sub-menu period configuration*

Item Period 1 to 8
USER
[PEriod X MEnu]*
[USEr] 0 Return to previous menu
1 Start of occupied period
USER1 USER2 SCHEDULE 1 SCHEDULE 2 HOLIDAYS HOUR + DATE BROADCAST 2 End of occupied period
[USEr 1] [USEr 2] [SCHEduLE 1]* [SCHEduLE 2]* [HOLIDAYS]* [dAtE]* [broAdCASE]*
3 Selection Monday
4 Selection Tuesday
5 Selection Wednesday
PERIOD 1 PERIOD 1 HOLIDAY 1 6 Selection Thursday
7 Selection Friday
8 Selection Saturday
PERIOD 2 PERIOD 2 HOLIDAY 2
9 Selection Sunday
10 Selection holidays
PERIOD 3 PERIOD 3 HOLIDAY 3

PERIOD 4 PERIOD 4 HOLIDAY 4

SUB-MENU HOLIDAY CONFIGURATION*
Item HOLIDAYS 1 to 16
PERIOD 5 PERIOD 5 HOLIDAY 5
[HoLidAy X MEnu]*
0 Return to previous menu
1 Start month holidays
PERIOD 6 PERIOD 6 HOLIDAY 6
3 Start day holidays
4 Number of days, holidays
PERIOD 7 PERIOD 7 HOLIDAY 7 * only displayed if configuration requires.

PERIOD 8 PERIOD 8 HOLIDAY 8

NOTE: The items in brackets show what is displayed on
the user interface.
...

...

...

HOLIDAY 15

HOLIDAY 16

21
4.3.11.3 - Description of the User 1 Configuration sub-menu

User 1 Configuration sub-menu

Item Format Units Comments
0 USEr MEnu - When selected this item authorises return to the previous menu.
1 [1] 0/1/2/3 Selection of lead circuit.
0 = automatic; 1 = circuit A; 2 = circuit B; 3 = circuit C
2 0/1 - Load sequence selection.
0 = balanced loading: compressors belonging to different circuits are started alternatively.
1 = priority loading: all compressors in the same circuit are started, before starting those in another circuit.
3 YES/no - Ramp loading select.
Yes = ramp enabled
No = ramp disabled
This configuration enables the ramp to be activated for heating or cooling (depending on configuration). This item refers to the
authorised low or high temperature rates, controlled by the water heat exchanger (°C/min). Ramp setting value can be configured
in the Setpoint menu.
4 1 to 15 min Delay at start-up. This value is reinitialised after power-up or when both circuits are halted by local, remote or CCN command.
No compressor will be started up until this pause has expired. However, the evaporator pump command will be activated
immediately. The safety lockout loop will not be checked until the pause has expired.
5 0/1/2/3/4 - Pump sequence select
0 = no pump
1 = one pump only
2 = two pumps with auto rotation
3 = pump #1 manual select
4 = pump #2 manual select
If the auto sequence is selected, the pump change-over occurs when the rotation delay is elapsed. If the manual sequence is
selected then, the selected pump is used in priority. Change-over occurs if one pump fails.
6 [1] 24 to 3000 hours Pump changeover delay. Displayed if auto pump sequence is selected. This parameter is used for pump auto-rotation: the
control tries to limit the pump run time difference to the pump changeover delay value. Change-over between pumps occurs
when this difference becomes greater than the configured pump changeover delay.
7 [1] «YES/no» - Pump shutdown in standby mode
Displayed if the unit controls a water pump. If this parameter is validated, the pump will be shut down when the standby mode is
active (in automatic heating/cooling changeover). It automatically restarts in heating or cooling mode.
8 [1] «YES/no» - Activation of the water flow control verification, when the pump is stopped.
Prevents the water flow alarm, when the pump has stopped and when the user/water flow rate safety loop is closed.
9 0/1/2/3/4 - Cooling setpoint reset select.
0 = reset not selected
1 = reset based on outdoor temperature
2 = reset based on return water temperature
3 = reset based on 4-20 mA input (of the energy management option is used)
4 = reset based on room temperature (if the energy management option is used and the room temperature sensor is installed)
10 0/1/2/3 - Heating setpoint reset select. Only displayed in heat pump mode.
0 = reset not selected
1 = reset based on outdoor temperature
2 = reset based on return water temperature
3 = reset based on 4-20 mA input (of the energy management option is used)
11 «YES/no» - Automatic cooling/heating changeover select.
12 0/1/2 - Demand limit
0 = no demand limit
1 = demand limit generated by the contact inputs
2 = demand limit generated by the 0-20 mA input
13 [1] nn mA Maximum demand limit signal. Only displayed if the energy management option is used.
14 [1] nn mA Minimum demand limit signal. Only displayed if the energy management option is used.
15 [1] nnn °C Boiler threshold. Outdoor air temperature limit; if the temperature is lower, the heat pump is stopped or only the boiler is used for
hot water production. Only for heat pumps controlling an additional boiler.
16 [1] 0 to 60 minutes Electric heating stage operation schedule. Permits configuration of a start-up delay after unit start-up during which the electric
heater stages are not allowed to start.
17 [1] «YES/no» - Electric heating safety stage. In this configuration the last electric heating stage is only activated in the safety mode (in case of
a unit fault that prevents unit operation in heat pump mode). The other electric heating stages operate normally.
18 [1] «YES/no» - Electric heater stages in defrost mode. If a circuit switches to defrost mode, the electric heater stages are allowed to start up
immediately.
19 [1] -20 to 0 °C Minimum outside temperature threshold in heating mode. If the outside temperature is below this value, no compressor is
allowed to start.
[1] This item shall be masked when not used.

22
4.3.11.4 - Description of the User 2 Configuration sub-menu

User 2 Configuration sub-menu

Item Format Units Comments
0 [1] USEr 2 Menu When selected this item authorises return to the previous menu.
1 «YES/no» - Periodic pump quick-start of the water pump(s)
Yes = the pump is started periodically when the unit is manually stopped.
No = periodic pump start is disabled
When the unit is manually stopped (e.g. during the winter season) the pump is started each day at 14.00 hours for 2 seconds. If
two pumps are available, pump #1 is started on odd days and pump #2 on even days.
2 n1n2n3 n4 - Night control mode - start time*
00:00 to 23:59 Authorises entering the time of day at which the night control mode starts. During this period the fan runs at low speed (to reduce
fan noise) and unit capacity is limited to the maximum night values.
3 n1n2n3 n4 - Night control mode - end time*
00:00 to 23:59 Authorises entering the time of day at which the night control mode ends.
4 0 to 100 % Minimum demand limit threshold in night mode. The unit capacity is never unloaded below this threshold, when the night
mode is active (low noise level).
5 0 or 65 to 99 - Schedule 1 clock number (for unit on/off schedule, see section 4.3.11.6)
0 = schedule in local operating mode
65 to 99 = schedule in CCN operating mode
6 0 or 65 to 99 - Schedule 2 clock number (schedule for setpoint selection, see section 4.3.11.6)
0 = schedule in local operating mode
65 to 99 = schedule in CCN operating mode
7 1 to 239 - CCN element address
No two network elements can have the same element number and bus number at the same time.
8 0 to 239 - CCN bus number
No two network elements can have the same element number and bus number at the same time.
9 0/1/2/3/4 - User interface description text language
0 = English
1 = Spanish
2 = French
3 = Portuguese
4 = other (requires additional remote downloading)
10 «YES/no» - Extended display selection
YES = description of available menu
No = description of deactivated menu. This item permits activation or deactivation of the display showing the menu items.
11 «YES/no» - Activation of the user password for all user configurations: date, time schedules and broadcast.
12 nnn - Software version number
This item shows the number of the software version used by this controller. Access is read only.
13 [1] nnn °C Boiler activation temperature threshold. If the outside temperature is below this value, the boiler is started.
14 «YES/no» - Ice storage mode authorisation
YES = the ice storage mode is authorised
No = the ice storage mode is not authorised
15 nn °C Outdoor temperature limit (maximum) for authorisation of free cooling
16 «YES/no» - Authorisation of pre-cooling by free cooling
YES = pre-cooling by the free cooling mode is authorised (i.e. free cooling is started when the difference between the outside
temperature and the leaving water temperature is higher than the threshold value of 8°C without taking into consideration the
temperature difference between the outside temperature and the set-point).
No = pre-cooling by the free cooling mode is not authorised (i.e. free cooling is only started when the difference between the
outside temperature and the set-point is higher than the threshold value of 8°C).
17 5 to 60 minutes Maximum duration of full load operation in free cooling
If the unit operates at full load in free cooling for this duration, and if the set-point temperature is not satisfied, the free cooling
session must be stopped to allow the unit to restart in normal cooling mode (using the compressors).
* n1n2: hours (00 to 23). The first time the Enter button is continuously pressed, the first two characters in the 4-digit display flash so that hours can be adjusted.
n3n4: minutes (00 to 59). Continuous pressing of the Enter key again causes the last two characters to flash so that minutes can be adjusted.
[1] This item shall be masked when not used.

23
4.3.11.5 - Description of Date and Time configuration sub-menu

Date & Time configuration sub-menu

Item Format Comments
0 dAtE MEnu When selected this item authorises return to the previous menu.
1 n1n2n3n4 Current time setting.
00:00 to 23:59 n1n2: hours (00 to 23). The first time the Enter button is continuously pressed, the first two characters in the 4-digit display flash so that hours
can be adjusted.
n3n4: minutes (00 to 59). Continuous pressing of the Enter key again causes the last two characters to flash and minutes can be adjusted.
2 Current day of week setting.
«Mon» Monday
«tUe» Tuesday
«uEd» Wednesday
«tHu» Thursday
«FrI» Friday
«SAt» Saturday
«Sun» Sunday
3 n1n2n3n4 Current day and month setting. The control mode is the same as for the time.
01:01 to 31:12 n1n2:day (01 to 31).
n3n4:month (01 to 12).
4 n1n2n3n4 Current year setting.
5 YES/no Summertime activation. One hour is added when summertime starts, and one hour is deducted when it ends. The time changes at 2.00 am.
6 nn Summertime start month control.
7 Summertime start day of the week control.
«Mon» Monday
«tUe» Tuesday
«uEd» Wednesday
«tHu» Thursday
«FrI» Friday
«SAt» Saturday
«Sun» Sunday
8 0 to 5 Summertime start week of the month control.
9 nn Summertime end month control.
10 Summertime end day of the week control.
«Mon» Monday
«tUe» Tuesday
«uEd» Wednesday
«tHu» Thursday
«FrI» Friday
«SAt» Saturday
«Sun» Sunday
11 nn Summertime end week of the month control.

4.3.11.6 - Description of the Time Schedules sub-menus Period X configuration sub-menus (X = 1 to 8)

The control provides two timer programs: schedule 1 and Item Format Comments
0 Period X Menu Indicates the period (X) you are going to configure.
schedule 2 that can be activated. When selected this item authorises a return to the
main menu.
The first timer program (schedule #1) provides a means to 1 n1n2n3n4 Occupied period - Start time*.
00:00 to 23:59 Authorises entering the time of day at which the
automatically switch the unit from an occupied mode to an occupied period starts.
unoccupied mode: the unit is started during occupied 2 n1n2n3n4 Occupied period - End time*.
00:00 to 23:59 Authorises entering the time of day at which the
periods. occupied period ends.
3 Mo- 0 or Mo- 1 1 = the period is in effect on Monday.
The second timer program (schedule #2) provides a means to 0 = period not in effect on Monday
4 tu- 0 or tu- 1 1 = the period is in effect on Tuesday.
automatically switch the active setpoint from an occupied 0 = period not in effect on Tuesday.
setpoint to an unoccupied setpoint: cooling setpoint 1 is 5 UE-0 or UE- 1 1 = the period is in effect on Wednesday.
used during occupied periods, cooling or heating setpoint 2 0 = period not in effect on Wednesday.
6 tH- 0 or tH- 1 1 = the period is in effect on Thursday.
during unoccupied periods. 0 = period not in effect on Thursday.
7 Fr-0 or Fr- 1 1 = the period is in effect on Friday.
Each schedule consists of eight time periods set by the 0 = period not in effect on Friday.
8 SA- 0 or SA- 1 1 = the period is in effect on Saturday.
operator. These time periods can be flagged to be in effect or 0 = period not in effect on Saturday.
not in effect on each day of the week plus a holiday period. 9 Su- 0 or Su- 1 1 = the period is in effect on Sunday.
The day begins at 00.00 hours and ends at 23.59 hours. 0 = period not in effect on Sunday.
10 Ho- 0 or Ho- 1 1 = the period is in effect on public holidays.
0 = period not in effect on public holidays.
Program is in unoccupied mode unless a schedule time * n1n2: hours (00 to 23). The first time the Enter button is continuously pressed,
period is in effect. If two periods overlap and are both the first two characters in the 4-digit display flash so that hours can be
adjusted.
active on the same day, the occupied mode takes priority n3n4: minutes (00 to 59). Continuous pressing of the Enter key again causes the
over the unoccupied period. last two characters to flash so that minutes can be adjusted.

Each of the eight periods can be displayed and changed

with the aid of a sub-sub-menu. The table below shows
how to access the period configuration. Method is the
same for the time schedule #1 or the time schedule #2.

24
Typical timer program: ATTENTION: The broadcast function must be activated
to utilise the holiday schedule, even if the unit is running
Time MON TUE WES THU FRI SAT SUN HOL
in stand-alone mode (not connected to CCN). See section
0 P1
4.3.11.8.
1 P1
2 P1
3 Holiday period X configuration sub-menus (X = 1 to 16)
Item Format Comments
4
0 HoLidAy X Sub-menu When selected this item authorises a return to
5
the configuration menu.
6
1 0 to 12 Start month of public holiday period
7 P2 P2 P3 P4 P4 P5 0 = period not in use
8 P2 P2 P3 P4 P4 P5 1 = January, 2 = February, etc.
9 P2 P2 P3 P4 P4 P5 2 0 to 31 Start day of public holiday period. 0 period
10 P2 P2 P3 P4 P4 P5 not in use.
11 P2 P2 P3 P4 P4 P5 3 0 to 99 days Duration of the public holiday period in days.
12 P2 P2 P3 P4 P4 Typical programming for public holidays:
A public holiday period lasting 1 day on 20th May, for instance, is configured as
13 P2 P2 P3 P4 P4
MON: Monday follows: start month = 5, start day = 20, duration = 1
14 P2 P2 P3 P4 P4 A public holiday period lasting 2 day on 25th May, for instance, is configured as
TUE: Tuesday
15 P2 P2 P3 P4 P4
WED: Wednesday follows: start month = 5, start day = 25, duration = 2
16 P2 P2 P3 P4 P4 THU: Thursday
17 P2 P2 P3 FRI: Friday 4.3.11.8 - Description of the Broadcast sub-menu
18 P3 SAT: Saturday
19 P3 SUN: Sunday
(broAdCASt)
20 P3 P6 HOL: Public holidays The controller provides a broadcast configuration menu
21 which you can use to configure the unit to be the CCN’s
22 Occupied
Unoccupied
broadcaster, responsible for transmitting the time, outdoor
23
temperature, and holiday flags to all system elements.

This menu also authorises setting the date of the daylight

Starts at Ends at Active on saving time. There should be only one broadcaster in a
P1: period 1 0h00 3h00 Monday CCN, so this table should not be configured if any other
P2: period 2 7h00 18h00 Monday and Tuesday system element is acting as broadcaster.
P3: period 3 7h00 21h00 Wednesday
P4: period 4 7h00 17h00 Thursday and Friday
P5: period 5 7h00 12h00 Saturday ATTENTION: If the unit operates in standalone mode
P6: period 6 20h00 21h00 Public holidays (not CCN connected) this menu can also must be used if
P7: period 7 Not used in this example the holiday function is used or to correct for daylight
P8: period 8 Not used in this example
saving time.
4.3.11.7 - Description of the Holidays sub-menus
This function is used to define 16 public holiday periods.
Each period is defined with the aid of three parameters:
the month, starting day and duration of the public holiday
period. During these public holidays the controller will be
in occupied or unoccupied mode, depending on the
programmed periods validated for public holidays.

Each of these public holiday periods can be displayed and

changed with the aid of a sub-menu.

Broadcast configuration sub-menu (broAdCASt)

Item Format Comments
0 broAdCASt MEnu When selected this item authorises a return to the main menu.
1 YES/no Determines whether or not the unit is a broadcast acknowledger when the unit is connected on a CCN network. There must be only one
broadcast acknowledger in a CCN.

Warning: if the unit operates in standalone mode (not CCN connected) this choice must be set to Yes if the holiday function is used (see
section 4.3.11.6) or if you want to configure the daylight saving time function.
2 0/1/2 This item permits activation or deactivation of the broadcast mode.
0 = the controller is not the broadcaster, and it is not useful to configure another selection in this table.
1 = broadcasts time, date, holidays and the outside temperature.
2 = for chillers only. Summertime and holidays are not taken into consideration without broadcasting the information on the bus.
3 nnn OAT Broadcaster bus number: it is the bus number of the system that has the outside air temperature sensor connected to it.
4 nnn OAT Broadcaster element number: it is the element number of the system element that has the outside air temperature sensor connected
to it.

25
4.3.12 - Description of the Alarms menu 4.3.14.1 - Description of the Runtimes 1 menu
This menu is used to display and reset up to 5 active alarms.
It also permits alarm reset. If no alarm is active this menu Runtimes menu [1]
is not accessible. Item Format Units Comments
0 RuntiME 1 menu - When selected this item authorises
return to the previous menu
Alarms menu 1 nnnn | M 10 | M100 hrs/10 or 100 Unit operating hours*
Item Format Comments 2 nnnn | M 10 | M100 hrs/10 or 100 Compressor A1 operating hours*
0 [1] X ALArM X alarms are active 3 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor A2 operating hours*
rESEt ALArM Reset of alarms is requested. 4 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor A3 operating hours*
5 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor A4 operating hours*
To reset all active alarms, continuously press the
6 nnnn | M 10 | M100 hrs/10 or 100 Compressor B1 operating hours*
Enter key. ‘rESET ALArM’ is then displayed.
Press the select key again: all alarms are reset. 7 nnnn | M 10 | M100 hrs/10 or 100 Compressor B2 operating hours*
1 [1] Alarm code text Current alarm code 1** 8 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor B3 operating hours*
2 [1] Alarm code text Current alarm code 2** 9 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor B4 operating hours*
3 [1] Alarm code text Current alarm code 3** 10 - | M 10 | M100 -/10 or 100 Machine starts*
4 [1] Alarm code text Current alarm code 4** 11 - | M 10 | M100 -/10 or 100 Compressor A1 starts*
5 [1] Alarm code text Current alarm code 5** 12 [1] - | M 10 | M100 -/10 or 100 Compressor A2 starts*
[1] This item is masked when nil 13 [1] - | M 10 | M100 -/10 or 100 Compressor A3 starts*
* See section “Alarm codes” 14 [1] - | M 10 | M100 -/10 or 100 Compressor A4 starts*
** Pressing the Enter key when alarm code is displayed causes the following 15 - | M 10 | M100 -/10 or 100 Compressor B1 starts*
message to be scrolled: 16 - | M 10 | M100 -/10 or 100 Compressor B2 starts*
“time of alarm” “date of alarm” “full CCN alarm message” 17 [1] - | M 10 | M100 -/10 or 100 Compressor B3 starts*
- “time of alarm”: xxhmm 18 [1] - | M 10 | M100 -/10 or 100 Compressor B4 starts*
- “date”: dd-mm
[1] This item is masked when not used
- “full CCN alarm message”: up to 64 characters
NOTES
* Certain values are divided by 10 or by 100, so that number of hours or
4.3.13 - Description of the Alarms History menu start-ups of less then 10 are displayed as 0.

Alarms History menu When the value is divided by 10 or by 100 it is displayed in turn with “M 10” or
“M100”.
Item Format Comments
0 [1] Alarm code text* Alarm history code 1**
1 [1] Alarm code text* Alarm history code 2** 4.3.14.2 - Description of Runtimes 2 menu
2 [1] Alarm code text* Alarm history code 3**
3 [1] Alarm code text* Alarm history code 4**
Runtimes menu [1]
4 [1] Alarm code text* Alarm history code 5**
Item Format Units Comments
5 [1] Alarm code text* Alarm history code 6**
0 RuntiME 2 menu - When selected this item
6 [1] Alarm code text* Alarm history code 7**
authorises return to the previous
7 [1] Alarm code text* Alarm history code 8** menu
8 [1] Alarm code text* Alarm history code 9** 1 [1] nnnn | M 10 | M100 hrs/10 or 100 Pump 1 operating hours*
9 [1] Alarm code text* Alarm history code 10** 2 [1] nnnn | M 10 | M100 hrs/10 or 100 Pump 2 operating hours*
10 [1] Alarm code text* Alarm history code 11** 3 [1] nnnn | M 10 | M100 hrs/10 or 100 Heat reclaim condenser pump
.... .... .... operating hours
19 [1] Alarm code text* Alarm history code 20** 4 nnnn - Compressor starts for compressor
[1] This item is masked when nil with most starts during the last
* See section “Alarm codes” hour
** Pressing the Enter key when alarm code is displayed causes the following 5 nnnn - 24 hours average number of
message to be scrolled: starts/hour, compressor
“time of alarm” “date of alarm” “full CCN alarm message” 6 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor C1 operating hours
- “time of alarm”: xxhmm
7 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor C2 operating hours
- “date”: dd-mm
- “full CCN alarm message”: up to 64 characters 8 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor C3 operating hours
9 [1] nnnn | M 10 | M100 hrs/10 or 100 Compressor C4 operating hours
10 [1] nnnn | M 10 | M100 -/10 or 100 Compressor C1 starts
4.3.14 - Description of the Runtime menu 11 [1] nnnn | M 10 | M100 -/10 or 100 Compressor C2 starts
12 [1] nnnn | M 10 | M100 -/10 or 100 Compressor C3 starts
13 [1] nnnn | M 10 | M100 -/10 or 100 Compressor C4 starts
RUNTIMES 14 [1] nnnn | M 10 | M100 -/10 or 100 No. of defrost cycles, circuit A
15 [1] nnnn | M 10 | M100 -/10 or 100 No. of defrost cycles, circuit B
16 [1] nnnn | M 10 | M100 -/10 or 100 Free cooling refrigerant pump
operating hours, circuit A
17 [1] nnnn | M 10 | M100 -/10 or 100 Free cooling refrigerant pump
operating hours, circuit B
RUNTIMES 1 RUNTIMES 2 RUNTIMES 3 MAINTENANCE
[runtiMES 1] [runtiMES 2] [runtiMES 3] [MAintEnAnCE] 18 [1] nnnn | M 10 | M100 -/10 or 100 Free cooling refrigerant pump
operating hours, circuit C
[1] This item is masked when not used

26
4.3.14.3 - Description of the Runtimes 3 menu 4.3.14.4 - Maintenance menu description
To be active, the maintenance function must be preset in
Runtimes menu the Service configuration.
Item Format Units Comments
0 RuntiME 3 menu - When selected this item
authorises return to the Item Format Description
previous menu 0 MAintEnAnCE MEnu When selected this item authorises return to the
1 nnnn | M 10 | M100 hrs/10 or 100 Fan A1 operating hours previous menu.
2 nnnn | M 10 | M100 hrs/10 or 100 Fan A2 operating hours 1 [1] 0 to 6 Deletes the maintenance alerts.
3 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan A3 operating hours 2 [1] YES/no Refrigerant control.
4 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan A4 operating hours 3 [1] YES/no Water loop rate to low
5 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan A5 operating hours 4 [1] nnnn Next primary pump maintenance operation in
nnn days. If the number of days = 0, the delay
6 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan A6 operating hours
before maintenance has elapsed.
7 nnnn | M 10 | M100 hrs/10 or 100 Fan B1 operating hours
5 [1] nnnn Next secondary pump maintenance operation in
8 nnnn | M 10 | M100 hrs/10 or 100 Fan B2 operating hours nnn days. If the number of days = 0, the delay
9 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan B3 operating hours before maintenance has elapsed.
10 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan B4 operating hours 6 [1] nnnn Next maintenance operation on the heat reclaim
11 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan B5 operating hours condenser pump. If the number of days = 0, the
12 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan B6 operating hours delay before maintenance has elapsed.
13 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C1 operating hours 7 [1] nnnn Next water filter maintenance operation in nnn
14 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C2 operating hours days. If the number of days = 0, the delay before
15 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C3 operating hours maintenance has elapsed.
16 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C4 operating hours [1] This item is masked when not used.
17 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C5 operating hours
18 [1] nnnn | M 10 | M100 hrs/10 or 100 Fan C6 operating hours
[1] This item is masked when not used

27
5 - PRO-DIALOG PLUS CONTROL OPERATION • Start/Stop schedule: occupied or unoccupied status of
the unit as determined by the chiller start/stop program
5.1 - Start/stop control (Schedule #1).
• Master control type. This parameter is used when the
The table below summarises the unit control type and stop unit is the master unit in a two chiller lead/lag arrange-
or go status with regard to the following parameters. ment. The master control type determines whether the
• Operating type: this is selected using the start/stop unit is to be controlled locally, remotely or through
button on the front of the user interface. CCN (this parameter is a Service configuration).
• Remote start/stop contacts: these contacts are used • CCN emergency shutdown: if this CCN command is
when the unit is in remote operating type (rEM). See activated, it shuts the unit down whatever the active
sections 3.6.2 and 3.6.3. operating type.
• CHIL_S_S: this network command relates to the chiller • General alarm: the unit is totally stopped due to failure.
start/stop when the unit is in CCN control (CCn).
Variable forced to disable: the unit is halted. Variable
forced to Enable: the unit runs in accordance with
schedule 1.

Active operating type Status of parameters Control Unit

LOFF L-ON L-SC rEM CCN MASt CHIL_S_S Remote Master Start/stop CCN General type mode
start/stop control schedule emergency alarm
contact type mode shutdown
- - - - - - - - - - Enable - - Off
- - - - - - - - - - - Yes - Off
Active - - - - - - - - - - - Local Off
- - Active - - - - - - Unoccupied - - Local Off
- - - Active - - - Off - - - - Remote Off
- - - Active - - - - - Unoccupied - - Remote Off
- - - - Active - Disable - - - - - CCN Off
- - - - Active - - - - Unoccupied - - CCN Off
- - - - - Active - - Local Unoccupied - - Local Off
- - - - - Active - Off Remote - - - Remote Off
- - - - - Active - - Remote Unoccupied - - Remote Off
- - - - - Active Disable - CCN - - - CCN Off
- - - - - Active - - CCN Unoccupied - - CCN Off
- Active - - - - - - - - Disable No Local On
- - Active - - - - - - Occupied Disable No Local On
- - - Active - - - On cooling - Occupied Disable No Remote On
- - - Active - - - On heating - Occupied Disable No Remote On
- - - Active - - - On auto - Occupied Disable No Remote On
- - - - Active - Enable - - Occupied Disable No CCN On
- - - - - Active - - Local Occupied Disable No Local On
- - - - - Active - On cooling Remote Occupied Disable No Remote On
- - - - - Active - On heating Remote Occupied Disable No Remote On
- - - - - Active - On auto Remote Occupied Disable No Remote On
- - - - - Active Enable - CCN Occupied Disable No CCN On

5.2 - Heating/cooling/standby operation

HEATING STANDBY COOLING
5.2.1 - General Outdoor
temperature
The heating/cooling/standby selection applies to all units.
But only 30RB (liquid chillers) units, controlling a boiler
can change over to heating mode. Heating/cooling control Heating Cooling
can be automatic or manual. threshold* threshold

* This threshold does not apply to cooling only units that do not control a boiler.
In automatic mode the outdoor temperature determines
the heating/cooling/standby changeover based on the two
threshold values configured by the user (see Setpoint menu
for cooling and heating mode changeover thresholds). If the
unit is in standby it does not cool or heat, and no compressor
can be activated. The diagram below summarises the
operating principle in automatic mode.

28
5.2.2 - Heating/cooling/auto selection • Remote heating/cooling contacts: these contacts are
The table below summarises the unit heating/cooling only active if the unit is under remote control. See
operation, based on the following parameters: sections 3.6.2 and 3.6.3.
• Control type: indicates whether the unit operates in • HC_SEL: this network command permits heating/
local, remote or CCN mode. See section 5.1. cooling/auto control, if the unit is in CCN operating
• Unit on/off status: indicates whether the unit is shut mode.
down (not authorised to start) or in operation (or • Outdoor temperature: determines the operation, if
authorised to start). the unit is in automatic heating/cooling/standby
• Heating/cooling/auto selection in local mode: changeover mode.
operating mode selected via the user interface. See
Information menu.

Parameter status
On/off status Control type Heating/cooling selection Remote heating/ HC_SEL Outdoor temperature Operating mode
in local mode cooling contacts
Off - - - - - Cooling
On Local Cooling - - - Cooling
On Local Heating - - - Heating
On Local Auto - - > Cooling threshold Cooling
On Local Auto - - < Heating threshold Heating*
On Local Auto - - Between cooling and heating thresholds Standby
On Remote - Cooling mode - - Cooling
On Remote - Heating mode - - Heating
On Remote - Auto mode - > Cooling threshold Cooling
On Remote - Auto mode - < Heating threshold Heating*
On Remote - Auto mode - Between cooling and heating thresholds Standby
On CCN - - Cooling - Cooling
On CCN - - Heating - Heating
On CCN - - Auto > Cooling threshold Cooling
On CCN - - Auto < Heating threshold Heating*
On CCN - - Auto Between cooling and heating thresholds Standby
* Does not apply to cooling only units that do not control a boiler.

5.3 - Evaporator water pump control 5.4 - Control interlock contact

The unit can control one or two evaporator water pumps. This contact checks the status of a loop (water flow switch
The evaporator water pump is turned on when this option and customer safety loop, see section 3.6). It prevents the
is configured (see User configuration) and when the unit is unit from starting if it is open when the delay at start-up has
in one of the on modes described above or in delay mode. expired. This open contact leads to an alarm shut-down, if
Since the minimum value for the delay at start-up is 1 minute the unit is running.
(configurable between 1 and 15 minutes), the pump will run
for at least one minute before the first compressor starts. 5.5 - Evaporator antifreeze protection
The pump is kept running for 20 seconds after the unit goes to
stop mode. The pump keeps working when the unit switches The heater for the evaporator and water pump (for units
from heating to cooling mode or vice-versa. It is turned off with a pump) can be energised to protect the evaporator, if
if the unit is shut down due to an alarm unless the fault is a it can be damaged by freezing, when the unit is shut down
frost protection error. The pump can be started in particular for a long time at low outdoor temperature.
operating conditions when the evaporator heater is active (see
section 5.5). See section 5.14 for the particular evaporator NOTE: Evaporator heater control parameters can be
pump control for the follower unit (master/slave assembly). modified, using the Service configuration.

If two pumps are controlled and the reversing function has 5.6 - Control point
been selected (see User 1 configuration), the control tries to
limit the pump run time delta to the configured pump change- The control point represents the water temperature that
over delay. If this delay has elapsed, the pump reversing the unit must produce. The inlet water is controlled by
function is activated, when the unit is running. During the default, but the outlet water can also be controlled
reversing function both pumps run together for two seconds. (requires a Service configuration modification).

If a pump has failed and a secondary pump is available, the Control point = active setpoint + reset
unit is stopped and started again with this pump.
5.6.1 - Active setpoint
The control provides a means to automatically start the Two setpoints can be selected as active in cooling mode and
pump each day at 14.00 hours for 2 seconds when the unit two in heating mode. Usually, the second cooling setpoint
is off. If the unit is fitted with two pumps, the first pump is is used for unoccupied periods. The second setpoint in
started on odd days and the second pump is started on heating mode is used for unoccupied periods.
even days. Starting the pump periodically for few seconds
increases the life-time of the pump bearings and the
tightness of the pump seal.

29
Depending on the current operations, the active setpoint The following tables summarise the possible selections
can be selected by choosing the item in the Information depending on the control types (local, remote or CCN)
menu, with the user’s volt-free contacts, with network and the following parameters:
commands or with the setpoint timer program (schedule 2). • Setpoint select in local control: item #13 of the Infor-
mation menu permits selection of the active setpoint,
if the unit is in local operating type.
• Heating/cooling operating mode.
• Control contacts 2: status of control contact 2.
• Schedule 2 status: schedule for setpoint selection.

Local operating mode

Heating/cooling operating Local setpoint selection Ice storage Ice storage contact Schedule 2 status Active setpoint
mode configuration [2] status [2]
Cooling sp 1 Cooling setpoint 1
Cooling sp 2 Cooling setpoint 2
Cooling [2] Auto Activated Unoccupied Ice storage setpoint
Cooling [2] Auto Activated Open Unoccupied Cooling setpoint 2
Cooling Auto Closed Occupied Cooling setpoint 1
Cooling Auto Deactivated Unoccupied Cooling setpoint 2
Heating sp 1 Heating setpoint 1
Heating sp 2 Heating setpoint 2
Heating Auto Occupied Heating setpoint 1
Heating Auto Unoccupied Heating setpoint 2

Remote operating mode

Heating/cooling operating Local setpoint Ice storage Ice storage contact Control contact 2 Active setpoint
mode selection configuration [2] status [2]
Cooling [2] sp control Control setpoint
Cooling sp 1 (open) Cooling setpoint 1
Cooling sp 2 (closed) Cooling setpoint 2
Cooling [2] Activated Open Cooling setpoint 1
Cooling [2] Activated Open Closed Ice storage setpoint
Cooling [2] Activated Closed Closed Cooling setpoint 2
Heating sp 1 (open) Heating setpoint 1
Heating sp 2 (closed) Heating setpoint 2

Remote operating mode - dual-circuit units

Parameter status
Heating/cooling operating mode Ice storage configuration [2] Ice storage contact status [2] Schedule 2 status Active setpoint
Cooling Occupied Cooling setpoint 1
Cooling Unoccupied Cooling setpoint 2
Cooling [2] Activated Open Unoccupied Ice storage setpoint
Cooling [2] Activated Closed Unoccupied Cooling setpoint 2
Heating Occupied Heating setpoint 1
Heating Unoccupied Heating setpoint 2
[2] Only with energy management option.

5.6.2 - Reset • A reference at which reset is zero (outdoor

Reset means that the active setpoint is modified so that temperature or delta T - no reset value).
less machine capacity is required (in cooling mode, the • A reference at which reset is maximum (outdoor
setpoint is increased, in heating mode it is decreased). This temperature or delta T - full reset value).
modification is in general a reaction to a drop in the load. • The maximum reset value.
For the Pro-Dialog control system, the source of the reset
can be configured in the User 1 configuration: it can be Reset example in cooling mode based on the outside
provided either by the outdoor temperature (that gives a temperature
measure of the load trends for the building) or by the return
water temperature (delta T that gives an average building
load) either for the reset setpoint based on a 4-20 mA input
(with energy management option) or based on the room
Reset value

% Building load

temperature, using a room temperature sensor (when the

energy management option is used). In response to a drop
in the outdoor temperature or to a drop in delta T, the
cooling setpoint is normally reset upwards in order to
optimise unit performance:
Outdoor temperature (OAT)
In the three cases the reset parameters, i.e. slope, source Evaporator Delta T
and maximum value, are configurable in the Setpoints
Legend
menu (see section 4.3.8). Reset is a linear function based A Maximum reset value C OAT or delta T for full reset
on three parameters. B OAT or delta T for no reset D Building Load

30
5.7 - Demand limit 5.11 - Defrost function

The demand limit is used to restrict the unit power consump- Defrost is activated, when the unit is in heating mode, in
tion. The Pro-Dialog control system allows limitation of order to reduce frost build-up on the air heat exchanger.
the unit capacity, using one of two methods: The defrost cycle can only be applied to one circuit at a
• by means of user-controlled volt-free contacts. The time. During the defrost cycle the fans of that circuit are
units without energy management option only have one stopped, and the four-way refrigerant valve is reversed,
demand limit level (only one contact: control contact 3). forcing the circuit to cooling mode. The fan can temporarily
The units equipped with energy management option be restarted during the defrost cycle. The defrost cycle is
permit three demand limit levels (2 contacts). The unit fully automatic and does not require any setting.
capacity can never exceed the limit setpoint activated
by these contacts. The limit setpoints can be modified 5.12 - Additional electric heater stage control
in the setpoint menu.
• by means of a 4-20 mA input type on the energy manage- The heat pump units can control up to four additional
ment board. The limit is now based on a linear interpo- electric heating stages.
lation from 0 to 100%, based on the input signal. The
demand limit in night mode is selectable (if the value The electric heating stages are activated to complement the
is below the one controlled by the external signal). heating capacity when the following conditions are satisfied:
• The unit uses 100% of the available heating capacity,
5.8 - Night mode or the unit is limited in its operation by a protection
mode (low suction temperature, hot gas or defrost
The night period is defined (see User configuration) by a sequence in progress protection), and in all cases
start time and an end time that are the same for each day cannot satisfy the heating load.
of the week. During the night period, the number of fans • The outdoor temperature is below a configured threshold
operating can be reduced, and the unit capacity may be (see User 1 configuration).
limited (but a minimum capacity value can be configured). • The unit demand limit is not active.

5.9 - Capacity control The user may configure the last available electric heating
stages as a safety stage. In this case, the safety stage is only
This function adjusts the number of active compressors to activated in addition to the other stages if there is a machine
keep the heat exchanger water temperature at its setpoint. fault, preventing the use of the heating capacity. The other
The precision with which this is achieved depends on the electric heating stages will continue to operate as described
capacity of the water loop, the flow rate, the load, and the above.
number of stages available on the unit. The control system
continuously takes account of the temperature error with 5.13 - Control of a boiler
respect to the setpoint, as well as the rate of change in this
error and the difference between entering and leaving NOTE: The control of the electric heating stages or of a
water temperatures, in order to determine the optimum boiler is not authorised for slave units.
moment at which to add or withdraw a capacity stage. If the
same compressor undergoes too many starts (per hour) or The unit can control the start-up of a boiler, if it is in heating
runs below one minute each time it is started this automa- mode. When the boiler is operating, the unit water pump is
tically brings about reduction of compressor starts, which stopped.
makes leaving water temperature control less precise. In
addition, the high pressure, low pressure or defrost unloading A heat pump unit and a boiler cannot operate together. In
functions can also affect the temperature control accuracy. this case the boiler output is activated in the following
Compressors are started and stopped in a sequence designed conditions:
to equalise the number of start-ups (value weighted by • The unit is in heating mode, but a fault prevents the
their operating time). use of the heat pump capacity.
• The unit is in heating mode, but works at a very low
5.10 - Head pressure control outdoor temperature, making the heat pump capacity
insufficient. The outdoor air temperature threshold
The head pressure is controlled by a maximum of six fans. for use of the boiler is fixed at -10°C, but this value
As an option, a variable-speed controller can control one or can be adjusted in the User 1 menu.
all of the fans. The head pressure is independently controlled
for each circuit, based on the saturated condensing tempe- 5.14 - Master/slave assembly
rature value.
Two PRO-DIALOG Plus units can be linked to produce a
Fan start-up: master/slave assembly. The two machines are interconnected
ATTENTION: The fans can be started periodically (for over the CCN bus. All parameters required for the master/
cleaning), even if the unit is switched off. slave function must be configured through the Service
configuration menu. Master/slave operation requires the
connection of a temperature probe at the common manifold
on each machine, if the heat exchanger leaving water
temperature is controlled.

31
The master/slave assembly can operate with constant or 5.15 - Optional heat reclaim module
variable flow. In the case of variable flow each machine
must control its own water pump and automatically shut This option requires the installation of an additional board.
down the pump, if the cooling capacity is zero. For constant
flow operation the pumps for each unit are continuously This board allows control of:
operating, if the system is operating. The master unit can • A heat reclaim condenser pump,
control a common pump that will be activated, when the • A heat reclaim condenser heater,
system is started. In this case the slave unit pump is not used. • Two solenoid valves to shut off the heat reclaim coil
(one for each circuit),
All control commands to the master/slave assembly (start/ • Two solenoid drain valves for the heat reclaim coil
stop, setpoint, heating/cooling operation, load shedding, (one for each circuit),
etc.) are handled by the unit which is configured as the • Two solenoid valves to shut off the water condenser
master, and must therefore only be applied to the master (one for each circuit),
unit. They will be transmitted automatically to the slave • Two solenoid drain valves for the water condenser
unit. The master unit can be controlled locally, remotely or (one for each circuit).
by CCN com-mands. Therefore to start up the assembly,
simply validate the Master operating type (MASt) on the Selecting the heat reclaim mode can be done with either
master unit. If the Master has been configured for remote the local interface or remotely with the (recl_sw) contact or
control then use the remote volt-free contacts for unit by CCN.
start/stop. The slave unit must stay in CCN operating type
continuously. To stop the master/slave assembly, select The heat reclaim function is active when: the heat reclaim
Local Off (LOFF) on the master unit or use the remote entering water temperature is lower than the heat reclaim
volt-free contacts if the unit has been configured for setpoint, minus half of the heat reclaim dead band.
remote control.
The heat reclaim function is not active when: the heat
One of the functions of the master unit (depending on its reclaim entering water temperature is higher than the heat
configuration) may be the designation, whether the master reclaim setpoint, plus half of the heat reclaim dead band.
or slave is to be the lead machine or the follower. The roles
of lead machine and follower will be reversed when the In the dead band the function remains in its active mode.
differ-ence in running hours between the two units exceeds The default value of the dead band is 4.4 K. This value can
a con-figurable value, ensuring that the running times of be modified by Carrier Service.
the two units are automatically equalised. The changeover
between lead machine and follower may take place when Changeover procedure from cooling to heat reclaim mode:
the assembly is started up, or even whilst running. The • Start-up of the condenser pump.
running time balancing function is not active if it has not • Verification of the condenser flow switch control
been configured: in this case the lead machine is always the contact. If this remains open after one minute of
master unit. condenser pump operation, the circuit remains in
cooling mode and an alarm will be activated.
The lead machine will always be started first. When the • As soon as the saturated condensing temperature
lead machine is at its full available capacity, start-up delay reaches 30°C, the pumpdown sequence is activated.
(configurable) is initialised on the follower. When this • Pumpdown: opening of the condenser water inlet
delay has expired, and if the error on the control point is valve and closing of the air condenser air valves 3
greater than 1.7°C, the follower unit is authorised to start seconds later.
and the pump is activated. The follower will automatically • After one minute or when the subcooling value is
use the master unit active setpoint. The lead machine will be above -10°C the heat reclaim function is effective.
held at its full available capacity for as long as the active
capacity on the follower is not zero. When the follower 5.16 - Free-cooling option
unit receives a command to stop, its evaporator water
pump is turned off with 20 seconds delay. The direct-expansion free-cooling principle is to circulate
the liquid refrigerant with a pump and to condense it to a
In the event of a communication fault between the two lower temperature at the condenser when the outside
units, each shall return to an autonomous operating mode temperature is low (below the setpoint). The performance
until the fault is cleared. If the master unit is halted due to achieved is huge, as only a pump and fans are activated.
an alarm, the slave unit is authorised to start without prior
conditions. This option requires the installation of an additional board
for each circuit. These boards allow control of:
ATTENTION: For heat pumps operating in master/slave • a three-way compressor shut-off valve
mode and with leaving water temperature control the first • a refrigerant pump.
AUX2 fan board must be replaced by the AUX1 board
and connected to a common temperature sensor. The following sensors are connected to each board:
• a pump suction pressure sensor
• a pump discharge pressure sensor
• a potentiometer to copy the position of the three-way
valve.

32
The prevention or authorisation of free cooling mode 6 - DIAGNOSTICS - TROUBLESHOOTING
operation can be controlled by the local interface or
remotely by customer contact 4 or by the CCN network. 6.1 - General

If pre-cooling is prohibited, free cooling starts if: The Pro-Dialog Plus control system has many fault tracing
• the outside temperature is lower than the aid functions. The local interface and its various menus
programmed threshold value (USER2 menu, item 15) give access to all unit operating conditions. If an operating
• the difference between outside temperature and fault is detected, an alarm is activated and an alarm code is
control point is higher than the minimum operating stored in the Alarm menu.
threshold value (4°C)
6.2 - Displaying alarms
If pre-cooling is authorised, free cooling starts if:
• the outside temperature is lower than the programmed The alarm LEDs on the summary interface (see section
threshold value (USER2 menu, item 15) 4.1) give a quick display of the status of each circuit and
• the difference between outside temperature and leaving the unit as a whole.
water temperature is higher than the minimum • A flashing LED shows that the circuit is operating but
operating threshold value (4°C) there is an alarm.
• A steady LED shows that the circuit has been shut
To stop the free cooling, a hysteresis of 0.5 K has been applied down due to a fault.
to these temperatures. When free cooling is stopped, a new
session is prohibited for one hour. The Alarm menu on the main interface displays up to 5
fault codes that are active on the unit.
Free cooling change-over procedure:
• The compressors stop (if the unit was operating) 6.3 - Resetting alarms
• The high/low pressure is equalised by opening the EXV
• The three-way valve receives the command to open When the cause of the alarm has been corrected the alarm
can be reset, depending on the type, either automatically on
Procedure to start up one circuit in free cooling: return to normal, or manually when action has been taken
• Wait for the complete opening of the three-way valve on the unit. Alarms can be reset even if the unit is running.
• Draw a vacuum and transfer the residual compressor
charge to the free-cooling circuit by starting up a This means that an alarm can be reset without stopping the
compressor (“pump-down”), machine. In the event of a power supply interrupt, the unit
• Start up the fans restarts automatically without the need for an external
• Cycle the pump (rotation for 10 seconds, shut-down command. However, any faults active when the supply is
for 4 seconds) interrupted are saved and may in certain cases prevent a
• Verify that a differential pressure is established at the circuit or a unit from restarting.
pump terminals.
A manual reset must be run from the main interface using
During free cooling operation all fans are activated except the following procedure:
when the differential between the outside temperature and
the leaving water temperature reaches a certain threshold Reset of active alarms
value. In this case only half of the fans are energised. Operation Item number Item value Press Menu
2-digit 4-digit button LED
display display
Expansion valve (EXV) control is based on the difference Hold down the MENU 0
button until the LED for
between the outside temperature and the leaving water alarms lights. The 4-digit
temperature to prevent disengaging or cavitation of the display shows the number
refrigerant pump. of active alarms (2 in this 0 2 ALArM
example).
Press the Enter button until 0 rESEt ALArM
The same pump stability logic can activate a pump-down “rESEt ALARrM” is shown
in the 4-digit display.
cycle, based on the pressure level detected in the compressors
at shut-down (up to three times in a free-cooling cycle) to
make the full refrigerant charge in the free-cooling circuit Press the Enter button 0 Good then,
again to validate the reset. 2 AL then,
available. “Good” is displayed for 2 no ALArM
seconds then, “2 ALArM”
and then, “no ALArM”.

33
6.4 - Alarm codes

The following list gives a complete description of each alarm code and its possible cause.

Alarm code descriptions

Alarm code Alarm description Reset type Probable cause Action taken by the control
Thermistor faults
th-01 Sensor fault, fluid entering water heat exchanger Automatic when the Defective thermistor Unit is shut down
temperature measured by
the sensor returns to normal
th-02 Sensor fault, fluid leaving water heat exchanger As above As above As above
th-03 Defrost fault, circuit A As above As above Circuit is shut down, if the unit is in heating
mode
th-04 Defrost fault, circuit B As above As above As above
th-08 Heat reclaim condenser inlet sensor fault As above As above The heat reclaim mode is stopped
th-09 Heat reclaim consenser outlet sensor fault As above As above As above
th-10 Outside temperature sensor fault As above As above Unit is shut down
th-11 CHWS fluid sensor fault (master/slave) As above As above The master/slave mode is stopped
th-12 Suction sensor fault, circuit A As above As above Circuit is shut down
th-13 Suction sensor fault, circuit B As above As above As above
th-14 Suction sensor fault, circuit C As above As above As above
th-18 Condenser subcooling liquid sensor fault, circuit A As above As above The heat reclaim mode of the circuit is stopped
th-19 Condenser subcooling liquid sensor fault, circuit B As above As above As above
th-21 Room temperature sensor fault As above As above Set-point control by the thermostat is stopped
Pressure transducers
Pr-01 Discharge pressure transducer fault, circuit A Automatic when the voltage Defective transducer Circuit is shut down
transmitted by the sensor or installation fault
returns to normal
Pr-02 Discharge pressure transducer fault, circuit B As above As above As above
Pr-03 Discharge pressure transducer fault, circuit C As above As above As above
Pr-04 Suction pressure transducer fault, circuit A As above As above As above
Pr-05 Suction pressure transducer fault, circuit B As above As above As above
Pr-06 Suction pressure transducer fault, circuit C As above As above As above
Pr-07 Heat reclaim pressure sensor, circuit A As above As above The heat reclaim mode is stopped
Pr-08 Heat reclaim pressure sensor, circuit B As above As above As above
Pr-16 Suction pressure sensor, free cooling refrigerant As above As above The free cooling mode is stopped
pump, circuit A
Pr-17 Discharge pressure sensor, free cooling refrigerant As above As above As above
pump, circuit A
Pr-18 Suction pressure sensor, free cooling refrigerant As above As above As above
pump, circuit B
Pr-19 Discharge pressure sensor, free cooling refrigerant As above As above As above
pump, circuit B
Pr-20 Suction pressure sensor, free cooling refrigerant As above As above As above
pump, circuit C
Pr-21 Discharge pressure sensor, free cooling refrigerant As above As above As above
pump, circuit C
Communication with slave boards
Co-a1 Communication loss with compressor A1 board Automatic when Installation bus fault or Compressor is shut down
communication is re- defective slave board
established
Co-a2 Communication loss with compressor A2 board As above As above As above
Co-a3 Communication loss with compressor A3 board As above As above As above
Co-a4 Communication loss with compressor A4 board As above As above As above
Co-b1 Communication loss with compressor B1 board As above As above As above
Co-b2 Communication loss with compressor B2 board As above As above As above
Co-b3 Communication loss with compressor B3 board As above As above As above
Co-b4 Communication loss with compressor B4 board As above As above As above
Co-c1 Communication loss with compressor C1 board As above As above As above
Co-c2 Communication loss with compressor C2 board As above As above As above
Co-c3 Communication loss with compressor C3 board As above As above As above
Co-c4 Communication loss with compressor C4 board As above As above As above
Co-e1 Communication loss with EXV No. 1 board As above As above Circuits A and B are shut down
Co-e2 Communication loss with EXV No. 2 board As above As above Circuit C is shut down
Co-f1 Communication loss with fan No. 1 board As above As above Circuit A is shut down (on certain units also
circuit B)
Co-f2 Communication loss with fan No. 2 board As above As above Circuit B is shut down
Co-f3 Communication loss with fan No. 3 board As above As above Circuit C is shut down
Co-02 Communication loss with electric heater board As above As above Electric heater control is stopped
Co-03 Communication loss with energy management As above As above The EMM accessory functions are stopped
board NRCP2
Co-04 Communication loss with heat recovery board As above As above Unit is shut down
NRCP2
Co-05 Communication loss with the AUX1 free-cooling Automatic, when the Bus installation fault Circuit A is shut down
board of circuit A communication is re- or slave board faulty
established
Co-06 Communication loss with the AUX1 free-cooling As above As above Circuit B is shut down
board of circuit B
Co-07 Communication loss with the AUX1 free-cooling As above As above Circuit C is shut down
board of circuit C

34
Alarm code descriptions (continued)
Alarm code Alarm description Reset type Probable cause Action taken by the control
Process faults
P-01 Water heat exchanger frost protection Automatic if the same alarm has Water flow rate to low or Unit is shut down
not tripped during the last 24 defective thermistor
hours, otherwise manual
P-05 Low suction temperature, circuit A Automatic when the temperature Pressure sensor defective, Circuit is shut down
returns to normal, and if this alarm EXV blocked or low
has not appeared during the last refrigerant charge
24 hours, otherwise manual
P-06 Low suction temperature, circuit B As above As above As above
P-07 Low suction temperature, circuit C As above As above As above
P-08 High superheat, circuit A As above As above As above
If free-cooling option is
used: 3-way valve position
incorrect
P-09 High superheat, circuit B As above As above As above
P-10 High superheat, circuit C As above As above As above
P-11 Low superheat, circuit A As above As above As above
If free-cooling option is
used: 3-way valve position
incorrect
P-12 Low superheat, circuit B As above As above As above
P-13 Low superheat, circuit C As above As above As above
P-14 Water flow control and customer interlock fault Automatic if the unit is in manual Evaporator pump defect or Unit is shut down
shut-down status, otherwise water flow switch fault
manual
P-15 Condenser water flow controller fault Manual Sensor defective The heat reclaim mode is stopped
P-16 Compressor A1 not started or no pressure increase Manual Connection problem Compressor is shut down
P-17 Compressor A2 not started or no pressure increase Manual Connection problem As above
P-18 Compressor A3 not started or no pressure increase Manual Connection problem As above
P-19 Compressor A4 not started or no pressure increase Manual Connection problem As above
P-20 Compressor B1 not started or no pressure increase Manual Connection problem As above
P-21 Compressor B2 not started or no pressure increase Manual Connection problem As above
P-22 Compressor B3 not started or no pressure increase Manual Connection problem As above
P-23 Compressor B4 not started or no pressure increase Manual Connection problem As above
P-24 Compressor C1 not started or no pressure increase Manual Connection problem As above
P-25 Compressor C2 not started or no pressure increase Manual Connection problem As above
P-26 Compressor C3 not started or no pressure increase Manual Connection problem As above
P-27 Compressor C4 not started or no pressure increase Manual Connection problem As above
P-28 Control box thermostat or phase reversal detected Automatic when the contact closes Control box badly Unit is shut down
again ventilated or poor
electrical connection
P-29 Communication loss with the System Manager Automatic when communication is CCN installation bus Unit goes into autonomous mode
re-established defective
P-30 Communicaiton loss between master and slave Automatic when communication is CCN installation bus As above
re-established defective
MC-nn Master chiller No. 1 configuration error at nn Automatic when the master Master/slave configuration Master/slave mode is stopped
configuration returns to normal or error
when the unit is no longer in
master/slave mode
FC-n0 No factory configuration Automatic when the configuration The unit size has not been Unit is shut down
is entered configured
FC-01 Illegal factory configuration number Manual The unit size has been As above
configured with the wrong
value
P-31 CCN emergency stop Manual Network command As above
P-32 Fault water pump 1 Manual Pump overheating or poor Unit is completely stopped if there is
pump connection no emergency pump
P-33 Fault water pump 2 Manual Pump overheating or poor As above
pump connection
P-34 Reclaim operation failure, circuit A Manual Sensor defective or low The heat reclaim mode of the circuit
condenser water flow rate is stopped
P-35 Reclaim operation failure, circuit B Manual Sensor defective or low As above
condenser water flow rate
P-37 Repeated high pressure unloading, circuit A Automatic Transducer defective or None
ventilation circuit fault
P-38 Repeated high pressure unloading, circuit B Automatic As above As above
P-39 Repeated high pressure unloading, circuit C Automatic As above As above
P-40 Repeated low suction temperature unloading in Manual Pressure sensor defective Circuit is shut down
heating mode, circuit A or refrigerant charge too
low
P-41 Repeated low suction temperature unloading in Manual As above As above
heating mode, circuit B
P-42 Repeated low suction temperature unloading, Manual As above As above
circuit C
P-43 Heat exchanger temperature too low, less than Automatic when the temperature Operating compressor The unit cannot start
10°C, prevents unit start-up detected returns to normal or protection out of range or
when the mode returns to cooling pressure sensor fault

35
Alarm code descriptions
Alarm code Alarm description Reset type Probable cause Action taken by the control
Process faults (cont’d)
P-91 Position of the free cooling 3-way valve Manual The valve has not reached Unit is shut down
incorrect for circuit A the expected position in the
time assigned
P-92 Position of the free cooling 3-way valve As above As above As above
incorrect for circuit B
P-93 Position of the free cooling 3-way valve As above As above As above
incorrect for circuit C
P-94 Operating fault in free cooling, circuit A Automatic, if the unit switches The refrigerant pump has The free cooling mode of the circuit is
back to normal cooling mode not correctly started or has stopped
cavitated
P-95 Operating fault in free cooling, circuit B As above As above As above
P-96 Operating fault in free cooling, circuit C As above As above As above
P-97 Reversed entering/leaving water sensors Manual Sensor defective, sensors Unit is stopped
reversed
CT-01 Fault, contactor stuck, circuit A Manual A compressor contactor is Ventilation and EXV control are maintained.
stuck, the compressor A second critical fault can result in the shut
cannot shut down down of the ventilation, closure of the EXV
and destruction of the compressor
CT-02 Fault, contactor stuck, circuit B As above As above As above
CT-03 Fault, contactor stuck, circuit C As above As above As above
V0-xx Fault, variable speed controller, circuit A Manual or automatic Speed controller fault or The circuit continues to operate, the speed
alert controller slows down the motor. The circuit
shuts down
V1-xx Fault, variable speed controller, circuit B As above As above As above
V2-xx Fault, variable speed controller, circuit C As above As above As above
Maintenance alarms
A1-01 Maintenance alert, service number nn Manual The preventive maintenance
date has passed
Compressor faults
A1-01 Fault, compressor A1 N°1 See compressor alarm subcode
A1-nn Fault, compressor A1 N°nn See compressor alarm subcode
A2-01 Fault, compressor A2 N°1 See compressor alarm subcode
A2-nn Fault, compressor A2 N°nn See compressor alarm subcode
A3-01 Fault, compressor A3 N°1 See compressor alarm subcode
A3-nn Fault, compressor A3 N°nn See compressor alarm subcode
A4-01 Fault, compressor A4 N°1 See compressor alarm subcode
A4-nn Fault, compressor A4 N°nn See compressor alarm subcode
B1-01 Fault, compressor B1 N°1 See compressor alarm subcode
B1-nn Fault, compressor B1 N°nn See compressor alarm subcode
B2-01 Fault, compressor B2 N°1 See compressor alarm subcode
B2-nn Fault, compressor B2 N°nn See compressor alarm subcode
B3-01 Fault, compressor B3 N°1 See compressor alarm subcode
B3-nn Fault, compressor B3 N°nn See compressor alarm subcode
B4-01 Fault, compressor B4 N°1 See compressor alarm subcode
B4-nn Fault, compressor B4 N°nn See compressor alarm subcode
C1-01 Fault, compressor C1 N°1 See compressor alarm subcode
C1-nn Fault, compressor C1 N°nn See compressor alarm subcode
C2-01 Fault, compressor C2 N°1 See compressor alarm subcode
C2-nn Fault, compressor C2 N°nn See compressor alarm subcode
C3-01 Fault, compressor C3 N°1 See compressor alarm subcode
C3-nn Fault, compressor C3 N°nn See compressor alarm subcode
C4-01 Fault, compressor C4 N°1 See compressor alarm subcode
C4-nn Fault, compressor C4 N°nn See compressor alarm subcode
Process faults
XX-01* Compressor B1 motor temperature too high Manual Motor fault, wiring The compressor is shut down
XX-02* Compressor B1 crankcase heater fault Manual Crankcase heater defective, As above
wiring fault
XX-03* Compressor B1 high pressure switch fault Manual Condenser flow rate too low, As above
condenser valve blocked, fan
circuit fault, condenser air or
water entering temperature
too high
XX-04* PTC temperature probe Manual Probe defective As above
Compressor motor B1 out of range
XX-05 Compressor board power supply is Automatic Unstable system voltage, Compressor is shut down
disconnected system power supply
unavailable
XX-06 Compressor board and contactor power Automatic Unstable system voltage, Compressor is shut down to avoid damage
supply drop system power supply to the contactors
unavailable
* XX-04 = A1 to A4, B1 to B4 and C1 to C4

Order No. 13440-76, 03.2013. Supersedes order No.: 13440-76,10.2011. Manufactured by: Carrier SCS, Montluel, France.
Manufacturer reserves the right to change any product specification without notice. Printed in the European Union.