Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    Install

    Uploaded by

    Bülent Bulut

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Install

    Uploaded by

    Bülent Bulut
    18 views1 page

    Original Title

    092304171425_install

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    18 views1 page

    Install

    Uploaded by

    Bülent Bulut

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ©2018 202220974-1118

    Exterior Storm Window


    Installation Instructions
    TOOLS REQUIRED
    Electric/cordless drill 3/32” drill bit Pliers For additional information on storm windows,
    Phillips screwdriver bit Utility knife Tape measure installation, and to register your new window, go to
    Caulk gun www.LARSONdoors.com/windows

    OVERLAP MOUNT INSTALLATION


    1. If your model includes an adjustable expander, slide the expander
    onto the bottom of the window unit. (The bottom mounting flange
    JAMB JAMB
    does not have round pre-punched installation holes).
    2. Position the storm window over the opening to check for a proper
    STORM WINDOW fit. Use caution when handling the window to ensure the glass
    BLIND STOP
    MOUNTING panes stay within the frame.
    FLANGE
    OPENING WIDTH If your storm window is too large, the mounting flange can be
    trimmed. Determine how much of the flange to remove. Using a
    BRICKMOLD GLASS utility knife, score the mounting flange along the appropriate grove.
    Bend the flange back and forth with pliers until it breaks off.

    3. Apply caulk to the head (top) and jambs (sides) of the existing
    window where the storm window will be mounted. To allow for
    BLINDSTOP MOUNT INSTALLATION proper drainage, DO NOT caulk the sill.
    4. Set the storm window in place, ensuring it is square, centered in
    JAMB JAMB the opening and that the frame does not bow toward or away from
    BLIND STOP the center of the window. Predrill a 3/32” pilot hole through each of
    STORM WINDOW MOUNTING
    the holes in the mounting flange, and secure window with the
    FLANGE provided screws.
    OPENING WIDTH BRICKMOLD 5. Adjust the expander (if applicable) so that it makes even contact
    GLASS across the window sill.

    GENERAL GLASS Wash using household glass cleaner or a warm water/mild detergent mixture and a
    CLEANING soft cloth or paper towel. A solution of four parts water/one part vinegar may also
    INSTRUCTIONS be used.

    SPECIAL CARE Clean the glass with plain water, using a clean soft sponge or lint-free cloth to
    FOR LOW-E GLASS remove as much surface grime from the glass as possible. If needed, wash the
    (SELECT MODELS) surface of the glass again with a solution of 80% water and 20% vinegar with a
    clean soft lint-free cloth. Dry with a new soft cloth.
    Cleaning may cause streaks when dried if the glass is exceptionally dirty. In this case
    repeat the above steps.

    Low
    NOTE:
    • Care must be exercised when using rubber squeegees on the coated surface, as

    E
    they can leave streaks that are hard to remove if they are used incorrectly or are in
    poor condition.
    • Never use ANY type of scraper or abrasive cleaner on the coated surface. Particles
    from these materials can be deposited on the coated surface and are very difficult
    S
    GLAS to remove.
    (Select Models)
    • For unusually hard to remove spots such as crayon or grease, isopropyl alcohol,
    SPECIAL CARE GooGone® or GoofOff® may be used. After spot cleaning, the full glass surface
    (Select Models) should be cleaned as discussed above.

    You might also like