13a25 PDF

FILE NO.
050-200503
(MFR’S VERSION A)
SERVICE MANUAL
COLOR TELEVISION
13A25
13A25C
DOCUMENT CREATED IN JAPAN, February, 2005

SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK
make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode-
resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Headphone jack
deal with it.
HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section of
the heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease may
cause damages to the IC and Transistor.)
A1-1 13A25/13A25C
ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF printing on the PCB.
(Please refer to figures.)
Caution:
• Pb free solder has a higher melting point than standard solder;
Typically the melting point is 50°F~70°F(30°C~40°C) higher.
Please use a soldering iron with temperature control and adjust it to 650°F ± 20°F (350°C ± 10°C).
In case of using high temperature soldering iron, please be carefull not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F/ 600°C).
• All products with the printed circuit board with PbF printing must be serviced with lead free solder.
When soldering or unsoldering, completely remove all of the solder from the pins or solder area,
and be sure to heat the soldering points with the lead free solder until it melts sufficiently.
Recommendations
Recommended lead free solder composition is Sn-3.0Ag-0.5Cu.
A1-2 13A25/13A25C
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING ...................................................................................................... A1-1

HOW TO ORDER PARTS ........................................................................................................................... A1-1
IMPORTANT ................................................................................................................................................ A1-1
ABOUT LEAD FREE SOLDER (PbF) ......................................................................................................... A1-2
TABLE OF CONTENTS .............................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................................... A3-1~A3-10
DISASSEMBLY INSTRUCTIONS
1.REMOVAL OF ANODE CAP .............................................................................................................. B1-1
2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................................... B2-1, B2-2
SERVICE MODE LIST ................................................................................................................................. C-1
CONFIRMATION OF HOURS USED .......................................................................................................... C-1
WHEN REPLACING EEPROM (MEMORY) IC ........................................................................................... C-1
ELECTRICAL ADJUSTMENTS .................................................................................................................. D-1~D-5
BLOCK DIAGRAM ...................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT ............................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ...................................................................................................................... G-1, G-2
TV POWER ............................................................................................................................................. G-3, G-4
DEFLECTION/CRT ................................................................................................................................. G-5, G-6
SOUND/AV ............................................................................................................................................. G-7, G-8
WAVEFORMS ............................................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEW .............................................................................................................. I-1, I-2
MECHANICAL REPLACEMENT PARTS LIST .......................................................................................... J1-1, J1-2
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................ J2-1~ J2-6
A2-1 13A25/13A25C
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G/0.18G
Color System NTSC
Speaker 1Speaker
Position Bottom
Size 3 Inch
Impedance 8 ohm
Sound Output MAX 1.0 W
10%(Typical) 0.8 W
NTSC3.58+4.43 /PAL60Hz No
G-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
54 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety UL
Radiation FCC
X-Radiation DHHS
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH
A3-1 13A25
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-8 OSD Language English French Spanish
G-9 Clock and Sleep Timer Max Time 120 Min

Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
A3-2 13A25
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No
A3-3 13A25
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
Type USA,ORION Type
BBE No
Auto Search No
CH Allocation No
SAP No
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer (Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
G-12 Accessories Owner's Manual Language English/Spanish[From '04 DEC O/R]
w/Guarantee Card Yes
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal -
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safeguard No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery Yes
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card (NDL Card) Yes
ESP Card No
300 ohm to 75 ohm Antenna Adapter No
A3-4 13A25
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power Yes
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal Ear Phone
Rear Video Input(Rear1) No
Video Input(Rear2) No
Audio Input(Rear1) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 362 x 360 x 320.5
G-15 Weight Net (Approx.) 9.5 kg ( 20.9 lbs)
Gross (Approx.) 11.0kg ( 24.4lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 440 x 408 x 380
Design As per Buyer's
Description of Origin Yes
Natural Dropping At 1 Corner / 3
Drop Test
Edges / 6 Surfaces
Height (cm) 62
Container Stuffing 866 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand Yes
G-18 Environment Pb Free Phase3
A3-5 13A25
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G/0.18G
Color System NTSC
Speaker 1Speaker
Position Bottom
Size 3 Inch
Impedance 8 ohm
Sound Output MAX 1.0 W
10%(Typical) 0.8 W
NTSC3.58+4.43 /PAL60Hz No
G-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
54 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety CSA
Radiation IC
X-Radiation HWC
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH
A3-6 13A25C
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip No
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating No
G-8 OSD Language English French Spanish
G-9 Clock and Sleep Timer Max Time 120 Min

Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
A3-7 13A25C
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No
A3-8 13A25C
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip No
Type
BBE No
Auto Search No
CH Allocation No
SAP No
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer (Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
G-12 Accessories Owner's Manual Language English/French
w/Guarantee Card Yes
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal -
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safeguard No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery Yes
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card (NDL Card) No
ESP Card No
300 ohm to 75 ohm Antenna Adapter No
A3-9 13A25C
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power Yes
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal Ear Phone
Rear Video Input(Rear1) No
Video Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 362 x 360 x 320.5
G-15 Weight Net (Approx.) 9.5 kg ( 20.9 lbs)
Gross (Approx.) 11.0kg ( 24.4lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 440 x 408 x 380
Design As per Buyer's
Description of Origin Yes
Natural Dropping At 1 Corner / 3
Drop Test
Edges / 6 Surfaces
Height (cm) 62
Container Stuffing 866 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand Yes
G-18 Environment Pb-free Soldering Yes
Parts Specificat Yes
A3-10 13A25C
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Fig. 1-3
GND on the CRT NOTE

Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver CRT
Support
Alligator Clip
Fig. 1-4
GND on the CRT Fig. 1-1
4. Insert one end of the Anode Support into the anode button,
2. Flip up the sides of the Rubber Cap in the direction of the then the other as shown in Fig. 1-5.
arrow and remove one side of the support.
Rubber Cap
Support
CRT
Fig. 1-5
CRT
Support 5. Confirm that the Support is securely connected.
Fig. 1-2
6. Put on the Rubber Cap without moving any parts.
B1-1 13A25/13A25C
2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using a
FLAT PACKAGE IC tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put Masking Tape (cotton tape) around the Flat Package
Some ICs on the PCB are affixed with glue, so be
IC to protect other parts from any damage. careful not to break or damage the foil of each IC leads
(Refer to Fig. 2-1.) or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within 10 Blower type IC
mm distance from IC leads. desoldering
machine
Masking Tape IC
(Cotton Tape)
Tweezers
Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not rotate or move the IC back and forth , until IC 5. Absorb the solder left on the pattern using the Braided
can move back and forth easily after desoldering the Shield Wire. (Refer to Fig. 2-4.)
leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
IC pattern
Fig. 2-2 Fig. 2-4
B2-1 13A25/13A25C
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-tip
1. Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.)
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.
Thin-tip Soldering Iron IC
Soldering Iron
Fig. 2-8
5. Finally, confirm the soldering status on four sides of the IC

Solder temporarily Solder temporarily
using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 2-5 position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, always be sure to replace the IC in this
case.
Solder Soldering Iron
IC Supply soldering
from upper position
to lower position
Fig. 2-6
3. Absorb the solder left on the lead using the Braided Shield
Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 2-7
B2-2 13A25/13A25C
SERVICE MODE LIST
This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter to the Service Mode, press both set key and remote control key for more than 2 seconds.
Set Key Remocon Key Operations
VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of factory data.
NOTE: Do not use this for normal servicing.
VOL. (-) MIN 1
If you set factory initialization, the memories are reset such as the channel setting,
and the POWER ON total hours.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Display of the Adjustment MENU on the screen.
VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set factory initialization, the total hours is reset to "0".
1. Set the VOLUME to minimum. ADDRESS DATA
2. Press both VOL. DOWN button on the set and Channel

button (6) on the remote control for more than 2 seconds.
INIT 00 D0 Initial setting content of MEMORY IC.
3. After the confirmation of using hours, turn off the power.
CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1
+ (ones digit value)
WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
*1
INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F INI USA CANADA
00 D0 04 EB 4E 47 B3 24 69 *1 00 00 05 90 D6 00 07 08 39 38
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. While holding down VOLUME button on front cabinet, press key (6) on remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9. Turn POWER on.
10. While holding down VOLUME button on front cabinet, press key (1) on remote control for more than 2 seconds.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.
C-1 13A25/13A25C
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS
ADJUSTMENTS 2-1: CUT OFF
Read and perform these adjustments when repairing the 1. Adjust the unit to the following settings.
circuits or replacing electrical parts or PCB assemblies. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
CAUTION B.BIAS=64, BRI.CENT=120, CONT.MAX=40.
• Use an isolation transformer when performing any 2. Place the set in Aging Test for more than 15 minutes.
service on this chassis. 3. Activate the adjustment mode display of Fig. 1-1 and
• Before removing the anode cap, discharge electricity press the channel button (01) on the remote control to
because it contains high voltage. select "CUT OFF".
• When removing a PCB or related component, after 4. Adjust the Screen Volume until a dim raster is obtained.
unfastening or changing a wire, be sure to put the wire
2-2: FOCUS
back in its original position.
• When you exchange IC and Transistor with a heat sink, 1. Receive the monoscope pattern.
apply silicon grease on the contact section of the heat 2. Turn the Focus Volume fully counterclockwise once.
sink. Befor applying new silicon grease, remove all the 3. Adjust the Focus Volume until picture is distinct.
old silicon grease. (Old grease may cause damages to
the IC and Transistor.) 2-3: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
Prepare the following measurement tools for electrical
adjustments. 1. Place the set in Aging Test for more than 10 minutes.
2. Receive the white 100% signal from the Pattern
1. Synchro Scope Generator.
2. Digital Voltmeter 3. Using the adjustment control, set the brightness and
On-Screen Display Adjustment contrast to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
1. In the condition of NO indication on the screen. press the channel button (10) on the remote control to
Press the VOL. DOWN button on the set and the select "R.BIAS".
Channel button (9) on the remote control for more than 5. Using the VOL. UP/DOWN button on the remote control,
2 seconds to appear the adjustment mode on the adjust the R.BIAS.
screen as shown in Fig. 1-1. 6. Press the CH. UP/DOWN button on the remote control to
select the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
TV adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.
8. Perform the above adjustments 6 and 7 until the white
color is achieved.
2-4: SUB TINT/SUB COLOR
1. Receive the color bar pattern. (RF Input)
00 OSD 19
2. Connect the oscilloscope to TP023.
Fig. 1-1 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
2. Use the Channel UP/DOWN button or Channel button select "TINT".
(0-9) on the remote control to select the options shown 4. Press the VOL. UP/DOWN button on the remote control
in Fig. 1-2. until the section "A" becomes as straight line.
3. Press the MENU button on the remote control to end (Refer to Fig. 2-1)
the adjustments. 5. Connect the oscilloscope to TP022.
NO. FUNCTION NO. FUNCTION press the channel button (19) on the remote control to
00 OSD H 16 CONTRAST CENT select "COL.CENT".
01 CUT OFF 17 CONTRAST MAX 7. Press the VOL. UP/DOWN button on the remote control
04 H.VCO 18 CONTRAST MIN until the red color level is adjusted to 110 ±10% of the
05 H.PHASE 19 COLOR CENT white level. (Refer to Fig. 2-2)
06 V.SIZE 20 COLOR MAX
07 V.SHIFT 21 COLOR MIN 8. Receive the color bar pattern. (Audio Video Input)
08 R.DRIVE 22 TINT 9. Press the TV/VIDEO button on the remote control to set
09 B.DRIVE 23 SHARPNESS to the AV mode. Then perform the above adjustments
10 R.BIAS 24 FM LEVEL 2~7.
11 G.BIAS 25 LEVEL
12 B.BIAS 26 SEPARATION 1
13 BRIGHT CENT 27 SEPARATION 2
14 BRIGHT MAX 28 TEST MONO
15 BRIGHT MIN 29 TEST STEREO
Fig. 1-2
D-1 13A25/13A25C
horizontal line
;;
;;
;;
;;; Notch
;;
;;
"A" ;;
Shadow mask
Fig. 2-1 Fig. 2-3
2-8: OSD HORIZONTAL

1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-4)
TV
White 100% Red 110%

Fig. 2-2
2-5: HORIZONTAL PHASE

00 OSD 19
1. Receive the monoscope pattern.
2. Using the adjustment control, set the brightness and
contrast to normal position. A B Fig. 2-4
press the channel button (05) on the remote control to
select "H.PHAS". 2-9: BRIGHT MANUAL
4. Press the VOL. UP/DOWN button on the remote 1. Receive the monoscope pattern.(RF Input)
control until the SHIFT quantity of the OVER SCAN on 2. Using the adjustment control, set the brightness and
right and left becomes minimum. contrast to normal position.
2-6: VERTICAL SIZE press the channel button (13) on the remote control to
1. Receive the monoscope Pattern. select "BRI.CENT".
2. Using the adjustment control, set the brightness and 4. Press the VOL.UP/DOWN button on the remote control
contrast to normal position. until the white 10% is starting to be visible.
3. Activate the adjustment mode display of Fig. 1-1 and 5. Press the TV/VIDEO button on the remote to set to the
press the channel button (06) on the remote control to AV mode. Then perform the above adjustment 2~4.
select "V.SIZE".
4. Press the VOL. UP/DOWN button on the remote control 2-10: SUB CONTRAST
until the SHIFT quantity of the OVER SCAN on upside 1. Receive an 70dB the color bar pattern.
and downside becomes 10 ± 2%. 2. Activate the adjustment mode display of Fig. 1-1
press the channel button (17) on the remote control
2-7: VERTICAL SHIFT to select "CONT.MAX".
1. Receive the monoscope Pattern. 3. Press the VOL. UP/DOWN button on the remote control
2. Using the adjustment control, set the brightness and until the contrast step No. becomes "43".
contrast to normal position. 4. Press the TV/VIDEO button on the remote control to set
3. Activate the adjustment mode display of Fig. 1-1 to the AV mode.
and press the channel button (07) on the remote 5. Activate the adiustment mode display of Fig. 1-1
control to select "V.SFT". paess the channel button (17) on the remote control
4. Press the VOL. UP/DOWN button on the remote to select "CONT.MAX".
control until the horizontal line becomes fit to the 6. Press the VOL.UP/DOWN button on the remote control
notch of the shadow mask. (Refer to Fig. 2-3) unitil the contrast step No. becomes "52".
7. Receive a broadcast and check if the picture is normal.
D-2 13A25/13A25C
2-11: Confirmation of Fixed Value (step No.)
Please check if the fixed values of the each adjustment
items are set correctly referring below. (RF/AV)
NO. FUNCTION STEP NO. NO. FUNCTION STEP NO.
04 H VCO 04 21 COLOR MIN 00
14 BRIGHT MAX 140 23 SHARPNESS 53
15 BRIGHT MIN 60 24 FM LEVEL 00
16 CONT CENT 30 25 LEVEL 00
18 CONT MIN 15 26 SEPARATION 1 00
20 COLOR MAX 74 27 SEPARATION 2 00
D-3 13A25/13A25C
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Receive the crosshatch pattern from the color bar
1. Turn the unit on and let it warm up for at least 30
generator.
minutes before performing the following adjustments.
2. Combine red and blue of the 3 color crosshatch pattern
2. Place the CRT surface facing east or west to reduce the
on the center of the screen by adjusting the pair of
terrestrial magnetism.
4 pole magnets.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted 3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar 1. Adjust the differences around the screen by moving
generator. the deflection yoke upward/downward and right/left.
3. Slide the deflection yoke until it touches the funnel (Refer to Fig. 3-2-a)
side of the CRT. 2. Insert three wedges between the deflection yoke
4. Adjust center of screen to green, with red and blue on the and
sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern.
RGB RGB
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B
8. Adjust the crosshatch pattern to change to white R
G
by repeating steps 6 and 7. B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW
Fig. 3-2-b
MAGNET SCREW
PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1
D-4 13A25/13A25C
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
CP806
R8
B
03
03
P8
R8
TP022
07
FB401 CP803A TU001
TP023
1
40
CP
01
CP802B
J8
CP801
CD801
CR
T
DY
GND CRT
DEGAUSS COIL
L503
CP502
S501B
CP802A
S501A
CD501
AC IN
CD101A
CD101B SPEAKER
MAIN PCB
D-5 13A25/13A25C
BLOCK DIAGRAM
TU001
2
EAR PHONE_JACK
10 11 12 13 17 3 J1001
CH. DOWN
1
IC1001 AN7511
VOL. DOWN
2 6
21 20 34 SPEAKER
SOUND AMP SP1001
CH. UP IC
4 8
66 ATT
VOL. UP RGB Proc.2
73 OSD SW Q801
CONTRAST BRIGHTNESS
67 RGB OUTPUT Stage 50 RED OUT
POWER
Chroma DRIVE
68 51
Proc. CUT OFF Q802
69 ACC/C-BPF HV BLK 52
OS101 I/O GREEN OUT
MCU APC/KILLER
70 IIC RGB Proc.1
CLK TINT/DEMO
1 TIM RGB MATRIX
INT COLOR CONT Q607
74 Q803
PWM
78 H-CTL
AD BLUE OUT
76 OSD Ver.Proc. Hor.Proc. 46
D106 Q105 Ver SYNC SEP SYNC SEPA/Hor. VCO
Ver.COUNT DOWN Hor.COUNT DOWN 45
SW
ROM V RAMP AFC-1/H COINCIDENT
RAM AFC-2 H PHASE Q402
J703 H. DRIVE
2 Q401
VCXO H. OUTPUT
J702
2
56 58 57 27 26 37 38 16 3 9 7
MICON/CHROM IC
IC101 OEC7091C X601 B G R
Q505 3.579545MHz V801
Heater
P. FAIL
V-OUT IC 4 F 8
IC501 IC401 LA78040N-E
T502 LTV-817M-VB
Q507 5 6
FEED BACK MEMORY IC PUMP UP
4 FEED BACK SW SDA SCL IC199
16
BR24L02F-WE2 -
AMP
8 Q502 DEGAUSS COIL +
BUFFER L503
13 VCC
7 1 3 6 5 DY
6
Q501 D501~D504
POWER AMP RECTIFIER FB401
9
Q503 1 F
PROTECT DRV. 2 S
L501 10 HV
2 4
3
1 3
F501
AC IN
E-1 13A25/13A25C E-2

MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
D408 CP601
C406
D404
R403
C435
HEATER
W003
R429
D410
D411
CP803A
GND
AFC
C420
S101A
ABL
D405
180V
W002
R410
W008
W007 C403
8V
TU001
C448_1
12V
CP4
T401
01
25V
COL
C434
+B
C401_1
C007
D412
C440_1 C43
7
FB401
R408_1 R421
C004
D001
L401 W001
C44
W062 3
R404
Q402 R503
W011
HS402
R409_1
D512
D509
D409
D506 R542
W830
Q401
R446
C446
Q501
R448 HS501
R427 W004
C511
R401_1
R449 R506
C516
W827
W010 Q502
W819
R520
S801X
D406
1 R417
40 C410_1 R508
IC R504 C510_1 C509
C51
C002 D516
W009 R510_1
47
4_1
01 R4
S4 R424 R418
D508
H
B501
D513
R413
C414 C417_2
R405
T502
R514
C526_1
C422
C418
R509
R501
W039
W038
C427
D502
R416
C521
D403
W037
W015
R415
IC501
L001
B504
R002
C515
C517_1
D501
C506
R422
W036
D510
W834 D503
W050
W006
D504
D505
R001 R527_2 C508 C503
W049 C518
C502
R445 C507
Q602 Q503
W048 Q601 W005 D528
R5
W802
W831 C617 Q603 W014
17
R523_2 CP502
R6 TP401
_1
R516
W019
29
R528
R518_1 D511 CP503
D515
W067
W046 C606 W817 L501
R515
W012 R507
W035
R602 R505 R603 R52

R537_1
R608 5 R513
W070
W034
Q505 C519 R512
C513_1
W810
W809
C601 D521 R502

C106 Q606
R423
W832
W833 L801 TH501_1

S801Y
D514
W025
D606
X601
RISK
C103
W040
W073
R604
_1
R519 Q507
_1
C602 W024 C623
05
03
W023
R8
R119
R130
R8
W065
OF FIRE - REPLACE AS MARKED.

FH502
C605 W069 D522
_1
W059 R538
S1
R804 CP806
CMD009A
D602
07
01
C
TP024
P8
B
R8
W058 W064 W020 C8
03
C615 W071 19
B
W057 R605
R601 TP022 C505
W816 R802
W056
Q802
F501
C621
W054
W018 S501B
W055
C616
C620_1
IC1001
W803
TP023
W017
C622 C809 Q801

W053 C628 R815
C610
CCD004A
W823 C1003
C1005
FH501
R606 R811 R816
C624_1
W828
W052
W051
C630
D604
R621 W068 W033 C808
C1001 CD501
S501A
R813 Q803
R607 C810
S102A
R5
W061
CP802A
R809 R814
R1001
D603
R611
00
R620
R614 W032 R806

W043
W045
W044
C1008 J8
R613 W031 01
Q105 S102B
R617
CP801
R615 W030
W066
W813 CP802B
W028
C633 W812
Q607
R616
W029
W027 R1007
R113
R112
OS101
R121
W808 CD101A C123
R110
R109
W042
W026
D106_1
J1001
C614
W041
C118
CD101B J703 J702
C612 SW101 SW102 SW103 SW104 SW105
R704_2
W060
W811
R701
F-1 13A25/13A25C F-2

F-3
C501
R101
CCD004A
R1005
C1004
R419 R1008
R1004
R420
C001 R1003 R126

R116 R143
SOLDER SIDE
R115
R004 R003
R107
R128
R106
R125 R618
R124
R127
C629
MAIN (CHIP MOUNTED PARTS)
R105
R129
64
R108
1
R627
R609
IC
10
1 C627
41
C626 C112_1
C102
R610
R103
25
C105 C104
R102
IC199_1
C107
C108
C101 R703
C603
R702
R104 C604
C609
CMD009A
13A25/13A25C
F-4
A B C D E F G H
MICON/CHROMA/TUNER SCHEMATIC DIAGRAM
IC199_1 BR24L02F-WE2
0 0 0 0
1 2 3 4
(MAIN PCB)
VSS
E1
E2
E0
MEMORY IC
8 8
50V 10 KA
C633
MODE
VCC
SDA
SCL
W823
W828
R621
4.9 5
47K 1/4W
8 7 6 5
R617
2.2K 1/2W
4.9 0 4.9 4.9 220 1/4W
H.CTL
5.6
R620
Q607
W808
R618 KTC3198
P.CON+5V
P.CON+5V
22K
3
H_OUT
H_CTL
FROM/TO DEFLECTION/CRT
R608
11E1-EIC ABCL
PROTECT
DEGAUSS_H
STANDBY_H
H_CTL
H_SYNC
G.OUT
R.OUT
B.OUT
7 C118 CLAMP 7
2 1K 1/4W
P.CON+B
6.3V 100 KA C101
V_OUT
R109
0.01 F
100 1/4W
100 1/4W
100 1/4W
GND
10K 1/4W C630
R610
V_FEEDBACK
10K
R110
1 MKT
D606
AT+5V
F
F
ABCL
C626
10K 1/4W
100P CH
C627
10K 1/4W 10V 470 YK
C112_1
C624_1
0.01
R105
R611
R124 H_OUT
0.01
4.7K
R609
R614
120K
R615
R613
X-RAY
50V 1 KA
10K C629
63V
SDA
1/4W
C628
1 CNVSS 41 NC
R616
R.OUT
R107
R130 0.01 F
R106
R108
4.7K
100
2 XIN 42 HVCO F/B
100
SCL G.OUT
C623
R627
1K
5 6 7
10K
3 XOUT 43 AFC FILTER 10K 1/4W
B.OUT
NC
4 TEST1 44 DEF GND 0 0 0 0 0 4.9 0.3 4.9 0 4.6 NC 2.3 3.2 3.2 3.5 8.0 0 8.0 4.6 4.9 0 3.4 3.7 0 NC 50V 2.2 KA
H_SYNC
5 VSS 45 FBP IN 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 7.9
6 R119 4.9 8.8 R607
8V REG 6
6 MCU VCC 46 H OUT 8.5 Q606
65
40
KTC3203_Y
7 TEST0 47 DEF VCC 22K 1/4W 4.6 100 1/4W
2.4
AFT MCU GND 11.3 FROM/TO TV POWER
66
39
8 FILT 48 NC 4
R112 2.2K 1/4W Ver.Proc. UNREG+12V
9 HLT 49 HI VCC 4.9 IIC BUS Hor.Proc. 4.5
KEY1 PGB OUTPUT Stage Ver SYNC SEP V_OUT
67
38
10 VHOLD 50 R OUT R113 2.2K 1/4W DECODER DRIVE SYNC SEPA/Hor.VCO POWER_FAIL
Ver.COUNT DOWN 2.6
4.9 CUT-OFF Hor.COUNT DOWN R606
11 CVIN 51 G OUT KEY2 SDA/SCL AFC-1/H COINCIDENT V RAMP V_FEEDBACK UNREG+12V
68
37
ROM HV BLK
R116 2.2K AFC-2 H PHASE
12 RESET IN 52 B OUT RAM OSD 0 22K 1/4W X-RAY
4.9
POWER_ON GND
69
36
13 MCU RESET OUT 53 ACL R115 22K
14 Y SW OUT 54 NC 4.9 3.3 C622 C621
REMOCON
70
35
15 V/C GND 55 PROTECT 0 I/O 4.0 50V 1 KA 16V 47 YK
AT+5V
16 3.58 XTAL 56 SDA AUDIO_OUT C620_1
71
34
NC RGB Proc.2
17 C-APC 57 H_CTL 4.9 OSD SW RGB Proc.1 4.6
5 1 0.01 B 5
72 RGB MATRIX
33
18 MCU5.7V REG OUT 58 SCL NC CONTRAST NC
BRIGHTNESS COLOR CONT D603 D604
19 NC 59 NC 4.9 P-ON CONT Power Manage. 3.1
AUDIO_MUTE IIC
73
32
MCU RESET NC 1SS133 FROM/TO SOUND/AV
20 CVBS IN3 60 NC MTZJ8.2B
2.9 TIM 8.8 R605
21 AUDIO IN3 61 NC R125 X-RAY CCD
74
31
INT Vldeo Proc. Chroma Proc.
22 V/C VCC 62 DEGAUSS_H 2.0 P.CON+5V 220 1/2W AUDIO_MUTE
47K R127 4.9 C-TRAP/YDELAY ACC/C-BPF
IIC_OFF NC
75
30
23 MCU TEST 63 STANDBY_H PWM APC/KILLER TUNER+5V VIDEO_IN
SHARPNESS
1K 0 CLK CONT TINT/DEMO 2.3
24 CVBS IN2 64 VOLUME AD MCU BLACK STRETCH S801X AUDIO_IN
ON_TIMER CPU core NC 5V REG
76
29
25 AUDIO IN2 65 NC CLK Y MUTE Q602 AUDIO_OUT
0 4.9
5.7 R604 KTC3203_Y
26 CVBS IN1 66 AFT P.CON+5V
77
28
NC LPF
27 AUDIO IN1 6bB AMP 5.5
67 KEY1
4.9 ATT 2.3 C614 100 1/4W 7.2 R629 GND
POWER_FAIL AUDIO_IN
78
27
28 5.7V REG OUT 68 KEY2 C617
VCO 2.0 50V 1 KA C612
29 C(Y/C) IN 69 POWER_ON R129 0 XO 22 3W
VIDEO_IN 10V 100 YK 7.2
79
26
4 30 Y(Y/C) IN 70 REMOCON
47K 4.9 50V 1 KA 5.5 C001 4
VCXO 2.2
31 VREG VCC 71 AV2
80
25
19
18
NC NC 5V REG 4.9 0.01 F
32 FSC OUT 72 AV1 Q603 NC 1 NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 KTC3203_Y C002
33 MONITOR OUT 73 AUDIO_MUTE
0 0 5.0 5.0 0 4.9 0 1.2 2.0 0.8 3.4 4.9 5.0 3.4 0 3.4 2.9 5.6 0 2.9 2.8 5.0 0 2.0 NC 2 NC
34 AUDIO ATT OUT 74 X-RAY MICON/CHROMA IC NC
NC NC
3.579545MHz
22P CH 100CT3R505
100 1/4W
470P B 1K 0.01 F
6.3V 1000 YK L001
R602
IC101
220P B 50V 1 KA
TUNER+5V
0.001 B
R102 C104
35 AUDIO ATT FILTER 75 IIC_OFF
50V 1 KA
C108
TUNER+5V 3
C601
OEC7091C
X601
C102 3.3uH 0305
36 TEST 3 76 ON_TIMER AT+5V
C106
NC 4 NC
10V 100 YK
37 V RAMP F/B 77 SYNC 0.01 F C615
TU_VIDEO
F
W833
C602
38 V RAMP OUT 78 POWER FAIL
C603
50V 1 KA NC 5 NC
0.1
C606
39 V RAMP CAP 79 NC
1K
C609 D602
16V 47 YK
C103
40 8.7V REG OUT 80 EXT_MUTE NC

W809
6 NC
0.022 F
R104
0.01 F
1M
C604
C105
MTZJ9.1B
R103
C107
C610
3 3
50V 1 KA
6.3V 47 KA C616
C605
TU_AUDIO NC 7 NC
W816
50V 1 KA
5.1 NC 8 NC
R601
1/4W
8.2K
0 ON_TIMER
NC 9 NC
SWITCHING
Q105 R004 TEST POINT
4.8 SCL
KRA102MAT SCL 10
CP601
REMOCON
POWER_ON
100
AT+5V
KEY1
R003
KEY2
SDA A2001WR2-6P
SDA 11
NC 6
100
AFT 12 AFT NC 5
IIC_OFF
R143 IIC_OFF 4
1/4W
TU_AUDIO 13 TU_AUDIO SDA

SDA 3
25V 10 KA
R121
47
0.022 B
SCL
C123
C007
2 R128 SCL 2 2
270
5V REG NC 14 NC
5.5 GND 1
560 Q601 R002 R001
R603 P.CON+B 15 P.CON+B
KTC3203_Y
POWER ON/ON TIMER
R126 R101 15K 1/2W 15K 1/2W
0.022 F
4.9
SLR-342VCT32
8.8 120 1/2W
C004
2.7K 560 NC 16 NC
D106_1
4.9
4.8
VOL DOWN
TU001
EVQ21505R
EVQ21505R
EVQ21505R
0
EVQ21505R
EVQ21505R
CH DOWN
TU_VIDEO
SW101
SW103
SW104
POWER
VOL UP
SW102
SW105
CH UP
115-V-KA35ARB TU_VIDEO 17
MTZJ33B
B+ 3
GND 2
1
D001
Vout
20
21
PCB010
CMD009
OS101
RPM7138-WH5
R.SIGNAL
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT G.SIGNAL 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES DEFLECTION SIGNAL
TUNER VIDEO SIGNAL
A B C D E F G H
G-1 13A25/13A25C G-2
A B C D E F G H
TV POWER SCHEMATIC DIAGRAM

(MAIN PCB)
8 8
CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.
4A 125V ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES

D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).
TO SOUND/AV
GND
R517_1
D505
SOUND+B
7 21DQ09N 1 1W 7
16V 1000 YK
C518
C519
500V 470P B
SOUND_GND
FROM/TO DEFLECTION/CRT
D510
+-10%
+B
2.7M 1/2W
DEGAUSS COIL
RU2AM-EIC
R500
L503 UNREG+12V
DYD1-3020-80 CP502 W802 W834
P.CON+B
A1561WV2-2P
C517_1 135.0 0
160V 100 MHE

1
1
6 2 2KV 820P RR
2
C521
100V 10 MHE
135.0 PROTECT DRIVE
C507
Q503
TH501_1 2SA1624
R501 R514
1
R523_2 R527_2
B59203-S1060-B14 CP503
5.6 5W C 0.22 1W
1N4005-EIC
003P-2100 47K 1/6W 5.6K 1/6W
1N4005-EIC
D502
1/2W
D501
R525
R510_1
3.3M
1.5 2W
GND
ECQUL
1/4W
B
1N4005-EIC
B
R528
500V 0.001
1/2W
1N4005-EIC
200V 220 YK
C503
D503
C502
500V 0.001
MTZJ18B
C526_1
C505
R538
D504
3 4
6.8K
275V 0.22
T502
D509
5 4A 125V FROM/TO MICON/CHROMA/TUNER 5
81291084
W832
1.5M
F501 1 2 POWER_FAIL
51MS040L
D521 0 R537_1
COIL,LINE FILTER D516 R504 R505 4.9
1.7 10.0 X-RAY
4A125V L501 8 11 P.FAIL 22K 1/4W
FH501 FH502 1N4937 100 1/4W 1K 1/4W
MTZJ6.8B Q505
50V 1 YK
1/4W
EYF-52BCY EYF-52BCY ELF15N010AP
0 4.8 KTA1266
C516
R516
NC 7 12
10K
144.0 132.3 B504 D513
6 13 UNREG+12V
W5RH3.5X5X1.0
16V 2200 YK
W5RH3.5X5X1.0 21DQ09N
0
B501
C515
NC 5 14 AT+5V
AC120V_60Hz
S501A
CD501
09414909 10.3 0
4 15 GND
4 4
S501B
BLACK
W819
6.6 11.3
C506 3 16
BLADE
WIDE
WHITE
2KV 820P RR
250V 0.001 KX 10.3

C514_1
144.0
2 17 NC
POWER AMP D R508
C509
1SS133
G 4.8
D512
Q501
2SK3563(ORION_Q) S 220 1W 0.047 M 18 NC
W827
0.1
12K 1/4W
1N4937
D515
R520
100 1/4W
R503
1SS133
D508
C511
W830
1/4W
R506
W810
50V 1 KA
3 BUFFER 3
1/4W
2.7K
R509
Q502
MTZJ18B
CH
KTC3198
C513_1
D506
0.68 1W
220
R542
1/4W
1/2W
R502
0.001
4.8 0.1
R515
100
0.0082 B
120K
HS501
C501
0
763WSAA021
C508
9.5
1/4W
6.0
R513
250V 0.0047 KX
FEED BACK
1SS133
1SS133
5.5
D522
2.2K
D514
SWITCHING
1SS133
Q507
D511
FEED BACK
KTC3198
IC501
LTV-817M-VB
2 C510_1 11.5 10.5 R519 2
R512
4
1/4W
1.2K 1/4W
0.1 F 680 1/4W
R507
3
27
0.1 9.5
MTZJ5.6B
D528
5.6K +-1%1/4W
R518_1
PCB010
CMD009
1 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
IS NON POLAR ONE.
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-3 13A25/13A25C G-4
A B C D E F G H
(CRT PCB)
CP802A CP802B
FROM MICON/CHROMA/TUNER DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB) GND
B2013H02-5P
GND 1 1
B2013H02-5P
GND
GND
CLAMP CLAMP
CLAMP CLAMP 2 2 CLAMP
G.OUT G.OUT
8 G.OUT G.OUT 3 3 G.OUT 8
R.OUT R.OUT
R.OUT R.OUT 4 4 R.OUT
B.OUT B.OUT
B.OUT B.OUT 5 5 B.OUT
V-OUT IC IC401 LA78040N-E
CP803A B2013H02-4P CP803B B2013H02-4P
HEATER HEATER
THERMAL HEATER 1 1 HEATER
PROTECTION GND GND
GND 2 2 GND
PUMP
UP AMP NC 3 3 NC
180V 180V
180V 4 4 180V
4.7K 1/4W
4.7K 1/4W
4.7K 1/4W
R811
R809
R814
1 2 3 4 5 6 7 CP801
3.5 25.0 2.0 0 12.0 25.0 3.5 CD801_1 TBS-X01X-A1
RED OUT GREEN OUT BLUE OUT
35V 100
C414
1 1 Q801 Q802 Q803
YK
2SC1473A 2SC1473A 2SC1473A
7 7
220uH
3.2 3.2 3.2
L801
8
R423 100.6 98.4 95.4
12
D403
100 1/4W 2.7 2.7 2.7
13
R424 V801
11E1-EIC
A34JXV70X73N45
330 1/2W
470 1/4W
100V 0.15
C422
R410
9
MKT
B
C808
C809
C810
10
330P
330P
R420
330P
R418 R
330 1/4W
8
330 1/4W
330 1/4W
G
R813
25V 470 YK
R815
R816
6
R419
22K 1/4W 2.7K R415
470
35V 22 YK
10K 1/4W
B
C418
11
R417
1/2W
1.8K 1/2W 5 7 1
C417_2
R416
50V 10 YK
2.2K 1/2W
2.2 1/2W
R413
1
C427
TO DY
HS401
R422
S801Y
6 763WSAA021 6
5 CP401 14 15 16
4 A1561WV2-A5P
3 TP022 TP024 TP023
100V 22 YK
10K +-1% 1/4W
C434
R429 NC 2
R408_1
1
4.7 1W
1/4W
2.7K 1/4W
2.7K 1/4W
1W
1W
15K 1W
D411
MTZJ5.1B
D412
15K
15K
2.7K
AU02A-EIC
R803_1
R805_1
R807_1
R802
R804
R806
FROM/TO MICON//CHROMA/TUNER
R401_1 R409_1
W831
5 X-RAY 5
27K +-1% 1/4W 27K +-1% 1/4W
P.CON+B
250V 4.7 YK
C401_1
250V 0.47 PMS
T401
4.7mH
L401
C437
9 ETH09K14BZ
3 4
NC 2
470 1/2W
150 1/2W
R446
1 6
GND
R404
H.DRIVE
V_FEEDBACK Q402
4 10 4
V_OUT
50V 22 YK
2SC1627_Y
ABCL 27.0 FB401 FNI14B002_M
C446
11
100V 0.01 MMTS
H_OUT 130.0 COL

0.3 1 HV
1.25KV 0.0084 MPP
H_SYNC 0 FOCUS
CH
C440_1
130.0
C410_1
CP806
1K 1/4W
H.OUTPUT
R405
0.001
FOCUS
C443
100 1/4W
0 Q401 132.5 VIDEO F

FROM/TO TV POWER 6 SCREEN
0
R427
2SC5885
2KV 0.001 B
SCREEN
C819
132.5 B+ S
GND 2
HS402 GND 0
48.0 11
TP401 763WSA0043 AFC
9
HEA ABL 4.3 96.4
7.0 7
W817 10 TER
+B
9
0
8
3 GND 3
R403 8
7
101.6
10K 1/4W NC 4 E12 GND 0
F
6
8
P.CON+B 25.0 E25 0
3
1
C406
5
E8
5 NC 0 0
4
3
500V 150P B
6.4 99.6 J801
ISMS01S
MTZJ6.2B
D404
AU02A-EIC
AU02A-EIC
D405
D410
R447
D406 PCB110
UNREG+12V
CCD004
150 2W 11E1-EIC
2 2
820P RR
11E1-EIC
D409
C420
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY
ARE
2KV
DESCRIBED IN PARTS LIST ONLY

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
R449 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
560 1/2W
R.SIGNAL
R448 NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
560 1/2W THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP G.SIGNAL
R445
IS NON POLAR ONE. B.SIGNAL
220K 1/4W
11E1-EIC
250V 22
180K 1/4W
100V 0.1
D408
C448_1
35V 470
MHE
1 1
R421
C403
C435
DEFLECTION SIGNAL
YK
YK
PCB010
CMD009 ATTENTION:LES PIECES REPAREES PAR UN ETANT
N’UTILISER QUE CELLS DECRITES
A B C D E F G H
G-5 13A25/13A25C G-6
A B C D E F G H
SOUND/AV SCHEMATIC DIAGRAM

8
(MAIN PCB) 8
RCA JACK WHITE

TO MICON/CHROMA/TUNER J703
ACCESSORY
AV1-09AD-4
19
R703
E
AUDIO 2 W811
7 AUDIO_IN 7
1
820
UM-4
20
R704_2
E
VIDEO 2 BT001
VIDEO_IN
1
GR03X-SP2
10 1/4W
68 1/4W
R701
R702
47K
RCA JACK YELLOW
UM-4
J702 TM101
RC-EH050(CT-859) BT002
AV1-09AD-3
GR03X-SP2
GND
6 6
EAR PHONE_JACK
5 J1001 5
MSJ-035-12A_PC
2
R1007 3
1
10 1/2W
KA
W812
C1008
16V 47
4 4
18
FROM TV POWER
CD101A
SOUND_GND SPEAKER
C3012004
1 1
SOUND+B 2 2
CD101B
SP1001
C3012005 S08F21A
GND 8.2 3.5 0 3.4
8 OHM
5 6 7 8
AN7511
SOUND AMP IC
+ -
3 3
FROM MICON/CHROMA/TUNER
IC1001
4 3 2 1
W813
R1001 5.1 0 0.3 3.9
AUDIO_MUTE
47K 1/4W
R1003
P.CON+5V
68K
KA
C1003
R1004
25V 10 KA
R1005
100K
270K
W803
C1005
2 2
C1004
50V
0.0022
R1008
GND
47K
C1001 17
AUDIO_OUT
50V 0.1 KA PCB010
CMD009
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
TUNER VIDEO SIGNAL
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES AUDIO SIGNAL
A B C D E F G H
G-7 13A25/13A25C G-8
WAVEFORMS
MICON/CHROMA/TUNER
1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div
2 20V 20µs/div 12 10V 5ms/div

7 1V 20µs/div
DEFLECTION/CRT
3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div
4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div
5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1 13A25/31A25C
WAVEFORMS
16 50V 20µs/div
SOUND/AV
17 0.5V 1ms/div
18 1V 1ms/div
19 200mV 500µs/div
20 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2 13A25/31A25C
MECHANICAL EXPLODED VIEW
202
107
202
202
202
121
201
102
104
202
111
201 PCB110
110 103
201 (CRT PCB ASS'Y)
111
205
111
201 204
106
203
111
106
106
101D 108 PCB010
120
(MAIN PCB ASS'Y)
101B
207
101C
206
109
101A
101
I-1 13A25/13A25C
MECHANICAL EXPLODED VIEW
(PACKING DIAGRAM)
105, 118, 119,

TM101 114
114
114
113
116
115
112
115
115
115
I-2 13A25/13A25C
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
101 AE006001 7A701A312A FRONT CABI ASS'Y

101A AE005701 701WPJC918 CABINET,FRONT
101B AE005702 713WPAA203 GLASS,LED
101C AE005703 713WPAA202 GUIDE,REMOCON
101D AE005704 735WPBB315 BUTTON,FRAME
102 AE006002 A3M131X740 CABINET,BACK ASS'Y
103 BZ710260 899HV3T000 HOLDER,ANODE WIRE

104 AE007109 726000A101 SHEET,CRT SERVICEMAN
105 AE005707 J3M13121A INSTRUCTION BOOK(E/S)
106 AE000535 800WQ0A024 FELT SHEET
107 AE005708 722549A412 SHEET,RATING
108 AE005650 723000C727 SHEET,CAUTION
109 AE005709 735WPAA837 SPEAKER HOLDER
110 BZ710660 741WUA0021 SPRING,EARTH

111 AE005971 769WSAA012 WASHER CRT T=0.5
112 AE007110 723000C835 SHEET,BARCODE
113 AE005712 791WHAA122 FILM BAG
114 AD300809 792WHAA052 PACKAGE,TOP
115 AD300810 792WHAA053 PACKAGE,BOTTOM
116 AE005713 793WCDC593 GIFT BOX
117 AE005714 A3M131V975 INSTRUCTION BOOK KIT
118 AE005715 JB5KD200 POLYBAG,INSTRUCTION(RED CAUTION)
119 AE004983 J2D60117A REGISTRATION CARD
201 AE005716 8121J50B5U SCREW,TAP TITE(P) GW20 5x28

202 AE004847 8117540A6U SCREW,TAP TITE(B0) TRUSS 4x16
203 AE003531 810763080U SCREW,TAP TITE(S) BRAZIER 3x8
204 AE005717 8109I3060U SCREW,TAP TITE(B) WH7 3x6
206 AE003528 8110630A0U SCREW,TAP TITE(P) BRAZIER 3x10
207 AE003529 811063080U SCREW,TAP TITE(P) BRAZIER 3x8
J1-1 13A25
MECHANICAL REPLACEMENT PARTS LIST
101 AE006001 7A701A312A FRONT CABI ASS'Y

101A AE005701 701WPJC918 CABINET,FRONT
101B AE005702 713WPAA203 GLASS,LED
101C AE005703 713WPAA202 GUIDE,REMOCON
101D AE005704 735WPBB315 BUTTON,FRAME
102 AE007111 A3M132X740 CABINET,BACK ASS'Y
103 BZ710260 899HV3T000 HOLDER,ANODE WIRE

104 AE007109 726000A101 SHEET,CRT SERVICEMAN
105 AE007112 J3M13221A INSTRUCTION BOOK
106 AE000535 800WQ0A024 FELT SHEET
107 AE007113 722549A440 SHEET,RATING
108 AE006290 723000C728 SHEET,CAUTION
109 AE005709 735WPAA837 SPEAKER HOLDER
110 BZ710660 741WUA0021 SPRING,EARTH

111 AE005971 769WSAA012 WASHER CRT T=0.5
112 AE007114 723000C853 SHEET,BARCODE
113 AE005712 791WHAA122 FILM BAG
114 AD300809 792WHAA052 PACKAGE,TOP
115 AD300810 792WHAA053 PACKAGE,BOTTOM
116 AE007115 793WCDC661 GIFT BOX
117 AE007116 A3M132X975 INSTRUCTION BOOK KIT
118 AE007117 JB5KD100 POLYBAG,INSTRUCTION(RED CAUTION)
120 AE000091 722000A023 SHEET,HWC

121 AE006166 722000A267 SHEET,CSA WARNING
201 AE005716 8121J50B5U SCREW,TAP TITE(P) GW20 5x28

202 AE004847 8117540A6U SCREW,TAP TITE(B0) TRUSS 4x16
203 AE003531 810763080U SCREW,TAP TITE(S) BRAZIER 3x8
206 AE003528 8110630A0U SCREW,TAP TITE(P) BRAZIER 3x10
207 AE003529 811063080U SCREW,TAP TITE(P) BRAZIER 3x8
J1-2 13A25C
ELECTRICAL REPLACEMENT PARTS LIST
RESISTORS
! R401 AE005733 R4K1T4273F R,METAL 2 27K OHM 1/4W
! R404 AE004065 R615U2151J R,FUSE 150 OHM 1/2W
! R429 AE005699 R638814R7J R,FUSE 4.7 OHM 1W
! R447 AE005729 R3K58A151J R,METAL OXIDE 150 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AE000366 R5X2CD5R6J R,CEMENT 5.6 OHM 5W
! R508 AE005727 R3K581221J R,METAL OXIDE 220 OHM 1W
R509 BZ210135 R002T4221J RC 220 OHM 1/4W
R510 AE003327 R00202335J RC 3.3M OHM 1/2W
R515 BZ210081 R002T2124J RC 120K OHM 1/2W
! R518 AE005734 R4K1T4562F R,METAL 5.6K OHM 1/4W
! R519 BZ210124 R002T4122J RC 1.2K OHM 1/4W
! R525 AE005730 R3K58A1R5J R,METAL OXIDE 1.5 OHM 2W
! R538 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R542 AE005728 R3K581R68J R,METAL OXIDE 0.68 OHM 1W
! R629 AE005731 R3K58B220J R,METAL OXIDE 22 OHM 3W
! R803 AE005689 R3K581153J R,METAL OXIDE 15K OHM 1W
CAPACITORS
! C403 BZ110149 E02LT4471M CE 470 UF 35V
! C414 AD301434 E02LU4101M CE 100 UF 35V
! C418 BZ110041 E02LT3471M CE 470 UF 25V
C420 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR
! C434 BZ110195 E02LU8220M CE 22 UF 100V
C437 BZ210173 P4J7F3474J CMPP 0.47 UF 250V PMS
! C443 AE001322 P4N8FJ842H CMPP 0.0084UF 1.25KV
C446 BZ110205 E02LU5220M CE 22 UF 50V
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
C503 BZ110061 C0JTB0513K CC 0.001 UF 500V B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C506 AD301026 CD39E0M13M CC 0.001 UF 250V
! C508 AE002878 CD39E0MQ3M CC 0.0047UF 250V
! C515 BZ110135 E02L02222M CE 2200 UF 16V
! C519 BZ110207 E02LT2102M CE 1000 UF 16V
! C521 BZ110092 E5EZFB101M CE 100 UF 160V
! C526 BZ110089 E02LFC221M CE 220 UF 200V
C819 BZ110247 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
D403 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D404 BZ410066 D97U06R21B DIODE,ZENER MTZJ6.2B T-77
! D405 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D406 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D412 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
! D501 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D505 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
! D512 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D515 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D516 AD300731 D2WXN49370 DIODE,SILICON 1N4937
J2-1 13A25
DIODES
ICS
IC101 AE005644 I56F07091C IC OEC7091C
IC199 AE005724 A3M131V015 INIT DATA BR24L02F-WE2
! IC401 AE002783 I03TD804N0 IC LA78040N-E
! IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
IC1001 BZ611001 I01DP75110 IC AN7511
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
! Q401 AE000656 TC1G058850 TRANSISTOR,SILICON 2SC5885
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q501 AE002251 T25F035630 FET 2SK3563(ORION_Q)
! Q502 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q601 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
! Q801 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
COILS &TRANSFORMERS
L001 AE000290 02167F3R3J COIL 3.3 UH
L401 AD301644 021L75472J COIL 4.7 MH
! L501 AE005719 0293000130 COIL,LINE FILTER ELF15N010AP
! L503 AE005718 028B140033 COIL,DEGAUSS DYD1-3020-80
L801 BZ310113 021673221K COIL 220 UH
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T502 AD302162 0481291084 TRANSFORMER,SWITCHING 81291084
JACKS
J702 AE005633 060Q401112 RCA JACK AV1-09AD-3
! J801 BZ614434 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
! J1001 AD302163 060J121014 JACK,RCA,3.5 MSJ-035-12A_PC
SWITCHES
SW101 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
P.C.BOARD ASSEMBLIES
PCB010 AE005723 A3M131V010 PCB ASS'Y CMD009A
PCB110 AE005725 A3M131V110 PCB ASS'Y CCD004A
MISCELLANEOUS
B501 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
BT001 AE005640 141R004016 BATTERY,MANGAN GR03X-SP2
! CD501 AE005639 1209414909 CORD,AC BUSH 9414909
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 BZ614283 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP503 BZ614016 069W01001A CONNECTOR PCB SIDE 003P-2100
CP601 AE005634 069S260639 CONNECTOR PCB SIDE A2001WR2-6P
CP801 AE007181 069W010340 CONNECTOR PCB SIDE 131001101K1
CD101A AE005720 06C3012004 CORD,CONNECTOR C3012004
CD101B AE005721 06C3012005 CORD,CONNECTOR C3012005
CP802A BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP802B BZ614276 067U005049 WIRE HOLDER B2013H02-5P
EL001 BZ614043 124116281A EYE LET XRY16X28BD
J2-2 13A25
MISCELLANEOUS
! F501 AD302166 081PC04005 FUSE 51MS040L
! FB401 AE003330 043214050F TRANSFORMER,FLYBACK FNI14B002_M
FH501 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-WH5
S101 AD302168 WBL6026038 FLAT CABLE AWM2468 AWG26 4C BLACK 260MM
S102 BZ614371 WCL6834038 FLAT CABLE AWM2468 AWG26 5C GRAY 340MM
! SP1001 AE005722 070Y132027 SPEAKER S08F21A
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AE003331 076N0EH050 TRANSMITTER RC-EH050(CT-859)
! TU001 AE006069 0163300018 RF UNIT 115-V-KA35ARB
! V801 BZ614442 098Y1404C8 CRT W/DY A34JXV70X73N45
X601 BZ613004 100CT3R505 CRYSTAL HC-49/U
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-3 13A25
RESISTORS
! R404 AE004065 R615U2151J R,FUSE 150 OHM 1/2W
! R447 AE005729 R3K58A151J R,METAL OXIDE 150 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AE000366 R5X2CD5R6J R,CEMENT 5.6 OHM 5W
R509 BZ210135 R002T4221J RC 220 OHM 1/4W
R510 AE003327 R00202335J RC 3.3M OHM 1/2W
R515 BZ210081 R002T2124J RC 120K OHM 1/2W
! R518 AE005734 R4K1T4562F R,METAL 5.6K OHM 1/4W
! R519 BZ210124 R002T4122J RC 1.2K OHM 1/4W
! R525 AE005730 R3K58A1R5J R,METAL OXIDE 1.5 OHM 2W
! R538 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R542 AE005728 R3K581R68J R,METAL OXIDE 0.68 OHM 1W
! R629 AE005731 R3K58B220J R,METAL OXIDE 22 OHM 3W
CAPACITORS
! C403 BZ110149 E02LT4471M CE 470 UF 35V
! C414 AD301434 E02LU4101M CE 100 UF 35V
! C418 BZ110041 E02LT3471M CE 470 UF 25V
! C434 BZ110195 E02LU8220M CE 22 UF 100V
C437 BZ210173 P4J7F3474J CMPP 0.47 UF 250V PMS
! C443 AE001322 P4N8FJ842H CMPP 0.0084UF 1.25KV
C446 BZ110205 E02LU5220M CE 22 UF 50V
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
C503 BZ110061 C0JTB0513K CC 0.001 UF 500V B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C506 AD301026 CD39E0M13M CC 0.001 UF 250V
! C508 AE002878 CD39E0MQ3M CC 0.0047UF 250V
! C515 BZ110135 E02L02222M CE 2200 UF 16V
! C519 BZ110207 E02LT2102M CE 1000 UF 16V
! C521 BZ110092 E5EZFB101M CE 100 UF 160V
! C526 BZ110089 E02LFC221M CE 220 UF 200V
C819 BZ110247 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
! D406 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D412 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
! D512 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D515 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D516 AD300731 D2WXN49370 DIODE,SILICON 1N4937
J2-4 13A25C
DIODES
ICS
IC101 AE005644 I56F07091C IC OEC7091C
IC199 AE007183 A3M132X015 INIT DATA BR24L02F-WE2
! IC401 AE002783 I03TD804N0 IC LA78040N-E
! IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
IC1001 BZ611001 I01DP75110 IC
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
! Q401 AE000656 TC1G058850 TRANSISTOR,SILICON 2SC5885
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q501 AE002251 T25F035630 FET 2SK3563(ORION_Q)
! Q502 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
COILS &TRANSFORMERS
L001 AE000290 02167F3R3J COIL 3.3 UH
L401 AD301644 021L75472J COIL 4.7 MH
! L501 AE005719 0293000130 COIL,LINE FILTER ELF15N010AP
! L503 AE005718 028B140033 COIL,DEGAUSS DYD1-3020-80
L801 BZ310113 021673221K COIL 220 UH
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T502 AD302162 0481291084 TRANSFORMER,SWITCHING 81291084
JACKS
! J801 BZ614434 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
! J1001 AD302163 060J121014 JACK,RCA,3.5 MSJ-035-12A_PC
SWITCHES
P.C.BOARD ASSEMBLIES
PCB010 AE007182 A3M132X010 PCB ASS'Y CMD009A
PCB110 AE005725 A3M131V110 PCB ASS'Y CCD004A
MISCELLANEOUS
! CD501 AE005639 1209414909 CORD,AC BUSH 9414909
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 BZ614283 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP503 BZ614016 069W01001A CONNECTOR PCB SIDE 003P-2100
CP601 AE005634 069S260639 CONNECTOR PCB SIDE A2001WR2-6P
CP801 AE007181 069W010340 CONNECTOR PCB SIDE 131001101K1
CD101A AE005720 06C3012004 CORD,CONNECTOR C3012004
CD101B AE005721 06C3012005 CORD,CONNECTOR C3012005
J2-5 13A25C
! F501 AD302166 081PC04005 FUSE 51MS040L
! FB401 AE003330 043214050F TRANSFORMER,FLYBACK FNI14B002_M
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-WH5
S101 AD302168 WBL6026038 FLAT CABLE AWM2468 AWG26 4C BLACK 260MM
S102 BZ614371 WCL6834038 FLAT CABLE AWM2468 AWG26 5C GRAY 340MM
! SP1001 AE005722 070Y132027 SPEAKER S08F21A
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AE003331 076N0EH050 TRANSMITTER RC-EH050(CT-859)
! TU001 AE006069 0163300018 RF UNIT 115-V-KA35ARB
! V801 BZ614442 098Y1404C8 CRT W/DY A34JXV70X73N45
X601 BZ613004 100CT3R505 CRYSTAL HC-49/U
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-6 13A25C
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN

13a25 PDF

Uploaded by

Copyright:

Available Formats

13a25 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

13a25 PDF

Uploaded by

Copyright:

Available Formats

FILE NO.

DOCUMENT CREATED IN JAPAN, February, 2005

HOW TO ORDER PARTS

SERVICING NOTICES ON CHECKING ...................................................................................................... A1-1

G-9 Clock and Sleep Timer Max Time 120 Min

G-9 Clock and Sleep Timer Max Time 120 Min

GND on the CRT NOTE

Braided Shield Wire

5. Finally, confirm the soldering status on four sides of the IC

Solder Soldering Iron

Braided Shield Wire

CONFIRMATION OF HOURS USED

2. Press both VOL. DOWN button on the set and Channel

WHEN REPLACING EEPROM (MEMORY) IC

Fig. 2-1 Fig. 2-3

2-8: OSD HORIZONTAL

White 100% Red 110%

2-5: HORIZONTAL PHASE

4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

E-1 13A25/13A25C E-2

R518_1 D511 CP503

W046 C606 W817 L501

R602 R505 R603 R52

Q505 C519 R512

C601 D521 R502

W833 L801 TH501_1

OF FIRE - REPLACE AS MARKED.

C622 C809 Q801

R614 W032 R806

F-1 13A25/13A25C F-2

C001 R1003 R126

MICON/CHROMA/TUNER SCHEMATIC DIAGRAM

6.3V 1000 YK L001

35 AUDIO ATT FILTER 75 IIC_OFF

40 8.7V REG OUT 80 EXT_MUTE NC

TU_AUDIO 13 TU_AUDIO SDA

R126 R101 15K 1/2W 15K 1/2W

8.8 120 1/2W

TV POWER SCHEMATIC DIAGRAM

CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

4A 125V ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES

160V 100 MHE

250V 0.001 KX 10.3

H_OUT 130.0 COL

0 Q401 132.5 VIDEO F

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

DESCRIBED IN PARTS LIST ONLY

SOUND/AV SCHEMATIC DIAGRAM

RCA JACK WHITE

1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div

2 20V 20µs/div 12 10V 5ms/div

3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div

4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div

5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div

105, 118, 119,

101 AE006001 7A701A312A FRONT CABI ASS'Y

102 AE006002 A3M131X740 CABINET,BACK ASS'Y

103 BZ710260 899HV3T000 HOLDER,ANODE WIRE

110 BZ710660 741WUA0021 SPRING,EARTH