Scribd
Upload
1K views2 pages

CAN-bus Interface

CAN-bus Interface

Uploaded by

mohamed abd el razek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

CAN-bus Interface

CAN-bus Interface

Uploaded by

mohamed abd el razek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

speedsignal GmbH

CAN-bus Interface
Type ADIF FI01
for:
Fiat: Fiat 500 (2007-), Fiorino (III, 2008-), Punto (2004-2007,
2005-2010, 2012-),
Punto Evo (2010-2011), Grande Punto (2005-), Stilo (2004-2008),
Doblo (I: 2001-2010, II: 2010-), Croma (2005-2010), Panda (2003-),
Idea (2003-)
Ford: Ka (RU8, 2009-)
Citroen: Nemo (2007-)
Peugeot: Bipper (2008-)
Only vehicles with interior- or comfort CAN-bus!

Copyright and technichal changes under reserve.


FI01/1 FI01/0 Available accessory for FI01/0:
plug-in for Harman/Becker systems and universal connexion, long cable,approx. 1m
many more length of cable approx. 0,15m

It is an interface to connect to vehicles CAN bus. It provides the


speed signal, ACC/ignition, illumination and reverse signal.

pin assignment table


colour of
I/O purpose note
wire
input ground black
input battery 12 V red The interface is designed for 12V DC.
input CAN high yellow At vehicle: grey/black or pink/black or blue**)
input CAN low brown At vehicle: white/green or pink/white or white**)
Output voltage:
output*) speedsignal white square signal 0 .. 12 Volt,
approx. 1 Hz per km/h (for KA version: 4 Hz per km/h)
output 0 V: off
output*) reverse gear signal green
output 12 V: on (reverse driving)
output 0 V: off (ACC/ignition off)
output*) ACC/ignition yellow/red
output 12 V: on (ACC/ignition on)
output 0 V: off (illumination off)
output*) illumination orange
output 12 V: on (illumination on)

*) The maximum current per output is 180 mA. However, the total current of all outputs together may not
exceed 200 mA. Otherwise, the interface could be destroyed. In case a higher current is needed (ignition,
reverse signal) use a relay with coil resistant of min. 75 Ω or min. 150 Ω if two relays are used.
**) The twisted pair is either grey/black and white/green or pink/black and pink/white or blue and white.

speedsignal GmbH +49-8061 / 49518-0 342FI01_R5_en


Carl-von-Ossietzky-Straße 3 +49-8061 / 49518-10 issue03/2015
83043 Bad Aibling revision 5
www.speedsignal.de page 1/2
How to connect the FI01/0:
1. remove car key from lock
2. unlink the 8pole Molex MiniFit plug
3. connect the single wire ends to the car as given in
pin assignment table and double check
4. reconnect the interface
5. switch on ACC / ignition and check performance of interface

How to find the CAN-bus at the vehicle:


At vehicles audio head unit connector (black 8 pole ISO).
Pin-
colour of wire signal
number
grey/black
CAN high
or
Pin 1 ( at FIAT defined as
pink/black
CAN B)
or blue
white/green
CAN low
or
Pin 3 ( at FIAT defined as
pink/white
CAN A)
or white
grey/black
CAN high

Copyright and technichal changes under reserve.


or
Pin 1 ( at FIAT defined as
pink/black
CAN B)
or blue
white/green front view,
CAN low
or numbering at OBD of vehicle
Pin 9 ( at FIAT defined as
pink/white
CAN A)
or white

How to connect other brands systems:


Please check this pin assignment with the navigation systems pin assignment and change if necessary. In
column „Blaupunkt“, you find the pin assignment for Blaupunkt systems. The difference is highlighted in blue.
PIN number
Harman/Becker / Sony / JVC /
connector A Blaupunkt
Pioneer / VDO Dayton MS 4150
(ISO) female
1 speedsignal speedsignal
2 reverse gear signal tel. Mute
3 tel. Mute reverse gear signal
4 Battery / constant +12V (Cl. 30) Battery / constant +12V (Cl. 30)
5 el. antenna / amplifier remote el. antenna / amplifier remote
6 Illumination (CL. 58) Illumination (CL. 58)
7 ACC / Ignition (CL. 15) ACC / Ignition (CL. 15)
8 Ground (CL. 31) Ground (CL. 31)

Disclaimer
Please strictly refer to the automobile manufacturers installation guide lines and terms of warranty when installing electronic units in automobiles. Inform the
customer(car owner) about the installation and the related risks. To disclaim, it may be useful to contact the automobiles manufacturer or an authorised
workshop.

speedsignal GmbH +49-8061 / 49518-0 342FI01_R5_en


Carl-von-Ossietzky-Straße 3 +49-8061 / 49518-10 issue03/2015
83043 Bad Aibling revision 5
www.speedsignal.de page 2/2

You might also like