Documentation

User Information

User Name
Address

Tel
Fax
E-Mail

Notes
 Device parametrized
Name, Date, Signature

Device parametrization checked

Name, Date, Signature

Device parametrization released

Name, Date, Signature

18-02-2020 9:18 AM Page 2

Promass 100

Promass 100

Promass 100
Access status tooling Service

Operation / Operation
Access status tooling Service Locking status ---

Operation / Totalizer handling / Totalizer

Control Totalizer 1 Totalize Preset value 2 0.00000 kg
Preset value 1 0.00000 kg Control Totalizer 3 Totalize
Control Totalizer 2 Totalize Preset value 3 500.00000 kg

Operation / Totalizer handling / Operation

Reset all totalizers Cancel

Setup / Setup
Device tag Promass 100

Setup / System units / System units

Mass flow unit kg/min Corrected volume unit Sm³
Mass unit kg Density unit kg/l
Volume flow unit m³/h Reference density unit kg/Nm³
Volume unit m³ Temperature unit °C
Corrected volume flow unit Sm³/h Pressure unit bar

Setup / Medium selection / Select medium

Select medium Liquid

Setup / Communication / Communication

MAC address 00-07-05-11-D0-CF IP address 192.168.1.31
Default network settings Off Subnet mask 255.255.255.0
DHCP client Off Default gateway 192.168.1.1

Setup / Low flow cut off / Low flow cut off

Assign process variable Mass flow Off value low flow cutoff 50 %
On value low flow cutoff 10.0000 kg/min Pressure shock suppression 0.1 s

Setup / Partially filled pipe detection / Partially filled pipe detection

Assign process variable Off

18-02-2020 9:18 AM Page 3

Promass 100

Setup / Advanced setup / Advanced setup

Enter access code 0

Setup / Advanced setup / Calculated values / Corrected volume flow calculation / Corrected volume flow
calculation
Corrected volume flow calculation Linear expansion coefficient 0.0000
Calculated reference density Square expansion coefficient 0.0000
Reference temperature 20.0000 °C

Setup / Advanced setup / Sensor adjustment / Sensor adjustment

Installation direction Flow in arrow direction

Setup / Advanced setup / Sensor adjustment / Zero point adjustment / Zero point adjustment
Zero point adjustment control Cancel Progress 100 %

Setup / Advanced setup / Totalizer 1 / Totalizer 1

Assign process variable Mass flow Totalizer operation mode Forward flow total
Unit totalizer kg Failure mode Stop

Setup / Advanced setup / Totalizer 2 / Totalizer 2

Assign process variable Mass flow Totalizer operation mode Forward flow total
Unit totalizer kg Failure mode Stop

Setup / Advanced setup / Totalizer 3 / Totalizer 3

Assign process variable Mass flow Totalizer operation mode Forward flow total
Unit totalizer kg Failure mode Stop

Setup / Advanced setup / Heartbeat setup / Heartbeat base settings / Heartbeat base settings
Record application reference data Cancel Plant operator --------------------------------
Progress 100 % Location --------------------------------
Status Not done

Setup / Advanced setup / Heartbeat setup / Heartbeat Verification / Heartbeat Verification

Select reference data Factory water calibration

Setup / Advanced setup / Administration / Administration

Define access code 0 Device reset Cancel

Diagnostics / Diagnostics
Actual diagnostics -------- Timestamp 0d00h00m00s
Timestamp 0d00h00m00s Operating time from restart 0d18h13m49s
Previous diagnostics -------- Operating time 746d18h33m07s

Diagnostics / Diagnostic list / Diagnostic list

Diagnostics 1 -------- Diagnostics 2 --------
Timestamp 0d00h00m00s Timestamp 0d00h00m00s

18-02-2020 9:18 AM Page 4

Promass 100

Diagnostics / Diagnostic list / Diagnostic list

Diagnostics 3 -------- Timestamp 0d00h00m00s
Timestamp 0d00h00m00s Diagnostics 5 --------
Diagnostics 4 -------- Timestamp 0d00h00m00s

Diagnostics / Event logbook / Event logbook

Filter options All Clear event list Cancel

Diagnostics / Device information / Device information 1

Device tag Promass 100 Device name Promass 100
Serial number M90FF002000 Order code 8E1B50-2HL2/0
Firmware version 01.02.01 ENP version 2.02.00

Diagnostics / Device information / Device information 1 / Extended order code

Extended order code 1 8E1B50-AADNAANSAD2SH Extended order code 3
Extended order code 2 +AA

Diagnostics / Device information / Device information 3

IP address 192.168.1.31 Default gateway 192.168.1.1
Subnet mask 255.255.255.0

Diagnostics / Measured values / Process variables / Process variables

Mass flow 0.0000 kg/min Reference density 1049.4970 kg/Nm³
Volume flow 0.0000 m³/h Temperature 26.2583 °C
Corrected volume flow 0.0000 Sm³/h Pressure value 1.0133 bar
Density 1.0494 kg/l

Diagnostics / Measured values / Totalizer / Totalizer

Totalizer value 1 649.74300 kg Totalizer overflow 2 0
Totalizer overflow 1 0 Totalizer value 3 1149.76700 kg
Totalizer value 2 649.76660 kg Totalizer overflow 3 0

Diagnostics / Heartbeat / Performing verification / Performing verification

Year 10 Start verification Cancel
Month January Progress 100 %
Day 1d Status Not done
Hour 12 h Overall result Check not done
Minute 0 min

Diagnostics / Heartbeat / Verification results / Verification results

Overall result Check not done

Diagnostics / Simulation / Simulation 1

Assign simulation process variable Off

18-02-2020 9:18 AM Page 5

Promass 100

Diagnostics / Simulation / Simulation 3

Simulation device alarm Off Simulation diagnostic event Off
Simulation diagnostic event 65533

Expert / Expert
Locking status --- Enter access code 0
Access status tooling Service

Expert / System / Diagnostic handling / Diagnostic handling

Alarm delay 0s

Expert / System / Diagnostic handling / Diagnostic behavior / Diagnostic behavior

Assign behavior of diagnostic no. 252 Alarm Assign behavior of diagnostic no. 913 Warning
Assign behavior of diagnostic no. 140 Warning Assign behavior of diagnostic no. 944 Warning
Assign behavior of diagnostic no. 046 Warning Assign behavior of diagnostic no. 948 Warning
Assign behavior of diagnostic no. 144 Alarm Assign behavior of diagnostic no. 192 Warning
Assign behavior of diagnostic no. 832 Warning Assign behavior of diagnostic no. 274 Warning
Assign behavior of diagnostic no. 833 Warning Assign behavior of diagnostic no. 392 Warning
Assign behavior of diagnostic no. 834 Warning Assign behavior of diagnostic no. 592 Warning
Assign behavior of diagnostic no. 835 Warning Assign behavior of diagnostic no. 992 Warning
Assign behavior of diagnostic no. 912 Warning

Expert / System / Administration / Administration

Define access code 0 Software option overview Extended HistoROM,
Device reset Cancel Heartbeat Verification,
Heartbeat Monitoring
Activate SW option 16859699

Expert / Sensor / Measured values / Process variables / Process variables

Mass flow 0.0000 kg/min Reference density 1049.4970 kg/Nm³
Volume flow 0.0000 m³/h Temperature 26.2583 °C
Corrected volume flow 0.0000 Sm³/h Pressure value 1.0133 bar
Density 1.0494 kg/l

Expert / Sensor / Measured values / Totalizer / Totalizer

Totalizer value 1 649.74300 kg Totalizer overflow 2 0
Totalizer overflow 1 0 Totalizer value 3 1149.76700 kg
Totalizer value 2 649.76660 kg Totalizer overflow 3 0

Expert / Sensor / System units / System units

Mass flow unit kg/min Density unit kg/l
Mass unit kg Reference density unit kg/Nm³
Volume flow unit m³/h Temperature unit °C
Volume unit m³ Pressure unit bar
Corrected volume flow unit Sm³/h Date/time format dd.mm.yy hh:mm
Corrected volume unit Sm³

18-02-2020 9:18 AM Page 6

Promass 100

Expert / Sensor / System units / User-specific units / User-specific units

User mass text User mass User corrected volume factor 1.0000
User mass offset 0.0000 User density text User dens.
User mass factor 1.0000 User density offset 0.0000
User volume text User vol. User density factor 1.0000
User volume offset 0.0000 User pressure text User pres.
User volume factor 1.0000 User pressure offset 0.0000
User corrected volume text UserCrVol. User pressure factor 1.0000
User corrected volume offset 0.0000

Expert / Sensor / Process parameters / Process parameters

Flow damping 0.00 s Temperature damping 0.00 s
Density damping 0.00 s Flow override Off

Expert / Sensor / Process parameters / Low flow cut off / Low flow cut off
Assign process variable Mass flow Off value low flow cutoff 50 %
On value low flow cutoff 10.0000 kg/min Pressure shock suppression 0.1 s

Expert / Sensor / Process parameters / Partially filled pipe detection / Partially filled pipe detection
Assign process variable Off

Expert / Sensor / Measurement mode / Measurement mode

Select medium Liquid

Expert / Sensor / External compensation / External compensation

Pressure compensation Off Temperature mode Internal measured value

Expert / Sensor / Calculated values / Corrected volume flow calculation / Corrected volume flow
calculation
Corrected volume flow calculation Linear expansion coefficient 0.0000
Calculated reference density Square expansion coefficient 0.0000
Reference temperature 20.0000 °C

Expert / Sensor / Sensor adjustment / Sensor adjustment

Installation direction Flow in arrow direction

Expert / Sensor / Sensor adjustment / Zero point adjustment / Zero point adjustment
Zero point adjustment control Cancel Progress 100 %

Expert / Sensor / Sensor adjustment / Density adjustment / Density adjustment

Density adjustment mode 1 point adjustment Progress 100 %
Density setpoint 1 1.0000 kg/l Density adjustment factor 1.0000
Execute density adjustment Ok Density adjustment offset 0.0000

Expert / Sensor / Sensor adjustment / Process variable adjustment / Process variable adjustment
Mass flow offset 0.0000 kg/s Mass flow factor 1.0000

18-02-2020 9:18 AM Page 7

Promass 100

Expert / Sensor / Sensor adjustment / Process variable adjustment / Process variable adjustment
Volume flow offset 0.0000 m³/s Corrected volume flow factor 1.0000
Volume flow factor 1.0000 Reference density offset 0.0000 kg/Nm³
Density offset 0.0000 kg/m³ Reference density factor 1.0000
Density factor 1.0000 Temperature offset 0.0000 K
Corrected volume flow offset 0.0000 Nm³/s Temperature factor 1.0000

Expert / Sensor / Calibration / Calibration

Calibration factor 1.88160 C5 0.0000000
Zero point -115 A0 295.7786000
Nominal diameter DN50 / 2" A1 5891.2000000
C0 -2076.7280000 A2 0.0000000
C1 575975900.0000000 A3 0.4838866
C2 -241909.7000000 A4 0.0000000
C3 0.0000000 Calibration date/time 26.09.17 00:07
C4 0.0000000

Expert / Sensor / Calibration / Logbook / Logbook

Calibration counter 1 Calibration factor 0 1.88160
Calibration date/time 0 26.09.17 00:07 Calibration factor 1 0.00000
Calibration date/time 1 00.00.00 00:00 Calibration factor 2 0.00000
Calibration date/time 2 00.00.00 00:00 Calibration factor 3 0.00000
Calibration date/time 3 00.00.00 00:00 Calibration factor 4 0.00000
Calibration date/time 4 00.00.00 00:00 Calibration factor 5 0.00000
Calibration date/time 5 00.00.00 00:00 Calibration factor 6 0.00000
Calibration date/time 6 00.00.00 00:00 Calibration factor 7 0.00000
Calibration date/time 7 00.00.00 00:00 Calibration factor 8 0.00000
Calibration date/time 8 00.00.00 00:00 Calibration factor 9 0.00000
Calibration date/time 9 00.00.00 00:00 Calibration factor 10 0.00000
Calibration date/time 10 00.00.00 00:00 Calibration factor 11 0.00000
Calibration date/time 11 00.00.00 00:00 Calibration factor 12 0.00000
Calibration date/time 12 00.00.00 00:00 Calibration factor 13 0.00000
Calibration date/time 13 00.00.00 00:00 Calibration factor 14 0.00000
Calibration date/time 14 00.00.00 00:00

Expert / Sensor / Testpoints / Testpoints

Oscillation frequency 0 426.872 Hz Oscillation damping 1 NaN
Oscillation frequency 1 NaN Hz Tube damping fluctuation 0 0.000534
Frequency fluctuation 0 0.000254 Tube damping fluctuation 1 NaN
Frequency fluctuation 1 NaN Signal asymmetry -0.4 %
Oscillation amplitude 0 34.3 % Electronic temperature 45.3 °C
Oscillation amplitude 1 NaN % Exciter current 0 0.025000 A
Oscillation damping 0 8260.13 Exciter current 1 NaN A

18-02-2020 9:18 AM Page 8

Promass 100

Expert / Sensor / Testpoints / Raw values

RawMassFlow -1.0941 kg/min

Expert / Sensor / Supervision / Oscillation

Limit value measuring tube damping 1000000.0000 A/m

Expert / Communication / Configuration / Configuration

MAC address 00-07-05-11-D0-CF Subnet mask 255.255.255.0
Default network settings Off Default gateway 192.168.1.1
DHCP client Off Web server functionality On
IP address 192.168.1.31

Expert / Communication / Configuration / Configurable input assembly / Configurable input assembly

Input assembly position 1 Mass flow Input assembly position 11 Mass flow unit
Input assembly position 2 Volume flow Input assembly position 12 Volume flow unit
Input assembly position 3 Corrected volume flow Input assembly position 13 Corrected volume flow unit
Input assembly position 4 Temperature Input assembly position 14 Temperature unit
Input assembly position 5 Density Input assembly position 15 Density unit
Input assembly position 6 Reference density Input assembly position 16 Reference density unit
Input assembly position 7 Supervision exciter current 1 Input assembly position 17 Current unit
Input assembly position 8 Totalizer 1 Input assembly position 18 Unit totalizer 1
Input assembly position 9 Totalizer 2 Input assembly position 19 Unit totalizer 2
Input assembly position 10 Totalizer 3 Input assembly position 20 Unit totalizer 3

Expert / Application / Application

Reset all totalizers Cancel

Expert / Application / Totalizer 1 / Totalizer 1

Assign process variable Mass flow Control Totalizer 1 Totalize
Unit totalizer kg Preset value 1 0.00000 kg
Totalizer operation mode Forward flow total Failure mode Stop

Expert / Application / Totalizer 2 / Totalizer 2

Assign process variable Mass flow Control Totalizer 2 Totalize
Unit totalizer kg Preset value 2 0.00000 kg
Totalizer operation mode Forward flow total Failure mode Stop

Expert / Application / Totalizer 3 / Totalizer 3

Assign process variable Mass flow Control Totalizer 3 Totalize
Unit totalizer kg Preset value 3 500.00000 kg
Totalizer operation mode Forward flow total Failure mode Stop

Expert / Application / Inventory counter / Inventory counter

Totalizer value 6302460.0000 kg Totalizer overflow 0

18-02-2020 9:18 AM Page 9

Promass 100

Expert / Diagnostics / Diagnostics

Actual diagnostics -------- Timestamp 0d00h00m00s
Timestamp 0d00h00m00s Operating time from restart 0d18h13m49s
Previous diagnostics -------- Operating time 746d18h33m07s

Expert / Diagnostics / Diagnostic list / Diagnostic list

Diagnostics 1 -------- Timestamp 0d00h00m00s
Timestamp 0d00h00m00s Diagnostics 4 --------
Diagnostics 2 -------- Timestamp 0d00h00m00s
Timestamp 0d00h00m00s Diagnostics 5 --------
Diagnostics 3 -------- Timestamp 0d00h00m00s

Expert / Diagnostics / Event logbook / Event logbook

Filter options All Clear event list Cancel

Expert / Diagnostics / Device information / Device information

Device tag Promass 100 Order code 8E1B50-2HL2/0
Serial number M90FF002000 Configuration counter 144
Firmware version 01.02.01 ENP version 2.02.00
Device name Promass 100

Expert / Diagnostics / Device information / Device information / Extended order code

Extended order code 1 8E1B50-AADNAANSAD2SH Extended order code 3
Extended order code 2 +AA

Expert / Diagnostics / Sensor module / Sensor module

Hardware revision V2.00.00 Serial number 5200641
Module name Promass E

Expert / Diagnostics / I/O module / I/O module

Software revision 10201 Module name K300
Build no. software 8 Serial number 0123451475
Hardware revision V1.00.00 Bootloader revision 20004

Expert / Diagnostics / Sensor electronic module / Sensor electronic module

Software revision 10301 Module name V300
Build no. software 3 Serial number 0131068351
Hardware revision V1.00.00 Bootloader revision 10001

Expert / Diagnostics / Min/max values / Min/max values

Reset min/max values Cancel

Expert / Diagnostics / Min/max values / Electronic temperature / Electronic temperature

Minimum value 22.9 °C Maximum value 56.6 °C

18-02-2020 9:18 AM Page 10

Promass 100

Expert / Diagnostics / Min/max values / Medium temperature / Medium temperature

Minimum value 19.6 °C Maximum value 35.4 °C

Expert / Diagnostics / Min/max values / Oscillation frequency / Oscillation frequency

Minimum value 415.3 Hz Maximum value 526.0 Hz

Expert / Diagnostics / Min/max values / Oscillation amplitude / Oscillation amplitude

Minimum value 2.0 % Maximum value 118.4 %

Expert / Diagnostics / Min/max values / Oscillation damping / Oscillation damping

Minimum value 295.4 Maximum value 350949.8

Expert / Diagnostics / Min/max values / Signal asymmetry / Signal asymmetry

Minimum value -1.6 % Maximum value 4.7 %

Expert / Diagnostics / Heartbeat / Heartbeat base settings / Heartbeat base settings

Record application reference data Cancel Plant operator --------------------------------
Progress 100 % Location --------------------------------
Status Not done

Expert / Diagnostics / Heartbeat / Heartbeat Verification / Heartbeat Verification

Select reference data Factory water calibration

Expert / Diagnostics / Heartbeat / Performing verification / Performing verification

Year 10 Start verification Cancel
Month January Progress 100 %
Day 1d Status Not done
Hour 12 h Overall result Check not done
Minute 0 min

Expert / Diagnostics / Heartbeat / Verification results / Verification results

Overall result Check not done

Expert / Diagnostics / Simulation / Simulation 1

Assign simulation process variable Off

Expert / Diagnostics / Simulation / Simulation 3

Simulation device alarm Off Simulation diagnostic event Off
Simulation diagnostic event 65533

18-02-2020 9:18 AM Page 11

 Event List

Event List
# Date - Time Operation Hours Event Description
(dddd:hh:mm:ss)
1 18-02-2020 9:19:06 0746:18:33:14 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
2 18-02-2020 9:19:06 0746:18:33:14 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
3 18-02-2020 9:19:00 0746:18:33:08 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
4 18-02-2020 9:19:00 0746:18:33:08 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
5 18-02-2020 9:18:28 0746:18:32:36 I1398 CDI: access status
AM changed
6 18-02-2020 9:17:36 0746:18:31:44 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
7 18-02-2020 9:17:36 0746:18:31:44 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
8 18-02-2020 9:17:25 0746:18:31:33 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
9 18-02-2020 9:17:25 0746:18:31:33 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
10 18-02-2020 9:16:41 0746:18:30:49 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
11 18-02-2020 9:16:41 0746:18:30:49 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
12 18-02-2020 9:16:41 0746:18:30:49 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
13 18-02-2020 9:16:41 0746:18:30:49 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
14 18-02-2020 9:16:24 0746:18:30:32 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
15 18-02-2020 9:16:24 0746:18:30:32 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 12

Event List
16 18-02-2020 9:15:58 0746:18:30:06 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
17 18-02-2020 9:15:58 0746:18:30:06 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
18 18-02-2020 9:15:46 0746:18:29:54 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
19 18-02-2020 9:15:46 0746:18:29:54 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
20 18-02-2020 9:15:32 0746:18:29:40 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
21 18-02-2020 9:15:32 0746:18:29:40 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
22 18-02-2020 9:15:09 0746:18:29:17 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
23 18-02-2020 9:15:09 0746:18:29:17 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
24 18-02-2020 9:14:47 0746:18:28:55 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
25 18-02-2020 9:14:47 0746:18:28:55 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
26 18-02-2020 9:14:42 0746:18:28:50 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
27 18-02-2020 9:14:42 0746:18:28:50 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
28 18-02-2020 9:14:33 0746:18:28:41 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
29 18-02-2020 9:14:33 0746:18:28:41 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
30 18-02-2020 9:14:27 0746:18:28:35 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
31 18-02-2020 9:14:27 0746:18:28:35 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
32 18-02-2020 9:13:55 0746:18:28:03 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 13

Event List
33 18-02-2020 9:13:55 0746:18:28:03 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
34 18-02-2020 9:13:53 0746:18:28:01 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
35 18-02-2020 9:13:53 0746:18:28:01 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
36 18-02-2020 9:13:49 0746:18:27:57 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
37 18-02-2020 9:13:49 0746:18:27:57 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
38 18-02-2020 9:13:44 0746:18:27:52 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
39 18-02-2020 9:13:44 0746:18:27:52 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
40 18-02-2020 9:13:38 0746:18:27:46 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
41 18-02-2020 9:13:38 0746:18:27:46 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
42 18-02-2020 9:13:29 0746:18:27:37 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
43 18-02-2020 9:13:29 0746:18:27:37 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
44 18-02-2020 9:13:27 0746:18:27:35 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
45 18-02-2020 9:13:27 0746:18:27:35 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
46 18-02-2020 9:13:25 0746:18:27:33 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
47 18-02-2020 9:13:24 0746:18:27:32 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
48 18-02-2020 9:13:20 0746:18:27:28 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
49 18-02-2020 9:13:20 0746:18:27:28 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 14

Event List
50 18-02-2020 9:13:17 0746:18:27:25 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
51 18-02-2020 9:13:17 0746:18:27:25 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
52 18-02-2020 9:13:13 0746:18:27:21 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
53 18-02-2020 9:13:13 0746:18:27:21 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
54 18-02-2020 9:13:13 0746:18:27:21 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
55 18-02-2020 9:13:13 0746:18:27:21 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
56 18-02-2020 9:13:11 0746:18:27:19 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
57 18-02-2020 9:13:11 0746:18:27:19 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
58 18-02-2020 9:13:10 0746:18:27:18 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
59 18-02-2020 9:13:10 0746:18:27:18 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
60 18-02-2020 9:13:09 0746:18:27:17 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
61 18-02-2020 9:13:09 0746:18:27:17 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
62 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
63 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
64 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
65 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
66 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 15

Event List
67 18-02-2020 9:13:07 0746:18:27:15 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
68 18-02-2020 9:13:06 0746:18:27:14 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
69 18-02-2020 9:13:06 0746:18:27:14 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
70 18-02-2020 9:13:04 0746:18:27:12 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
71 18-02-2020 9:13:04 0746:18:27:12 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
72 18-02-2020 9:13:03 0746:18:27:11 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
73 18-02-2020 9:13:03 0746:18:27:11 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
74 18-02-2020 9:13:03 0746:18:27:11 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
75 18-02-2020 9:13:03 0746:18:27:11 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
76 18-02-2020 9:13:01 0746:18:27:09 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
77 18-02-2020 9:13:01 0746:18:27:09 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
78 18-02-2020 9:13:01 0746:18:27:09 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
79 18-02-2020 9:13:01 0746:18:27:09 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
80 18-02-2020 9:13:00 0746:18:27:08 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
81 18-02-2020 9:13:00 0746:18:27:08 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
82 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
83 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 16

Event List
84 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
85 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
86 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
87 18-02-2020 9:12:59 0746:18:27:07 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
88 18-02-2020 9:12:58 0746:18:27:06 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
89 18-02-2020 9:12:58 0746:18:27:06 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
90 18-02-2020 9:12:57 0746:18:27:05 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
91 18-02-2020 9:12:57 0746:18:27:05 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
92 18-02-2020 9:12:57 0746:18:27:05 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
93 18-02-2020 9:12:56 0746:18:27:04 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
94 18-02-2020 9:12:56 0746:18:27:04 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
95 18-02-2020 9:12:56 0746:18:27:04 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
96 18-02-2020 9:12:56 0746:18:27:04 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
97 18-02-2020 9:12:56 0746:18:27:04 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
98 18-02-2020 9:12:54 0746:18:27:02 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
99 18-02-2020 9:12:54 0746:18:27:02 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)
100 18-02-2020 9:12:54 0746:18:27:02 S842 Process limit Low flow cut off active!
AM 1. Check low flow cut off configuration
(Service ID:145)

18-02-2020 9:18 AM Page 17

 Concentration Module

Promass F
Calibration type: Standard calibration (Field density adjustment: No )
Liquid/Application: Defined liquid Aquaeous glucose
Table data of concentration range [%] Low: 0 High: 100
Table data of temperature range [°C] Low: 10 High: 45
Quantity of table data:
Measuring uncertainty of density: +/- 0.01 kg/l

Measuring uncertainty of temperature: +/- 0.5 °C

Coefficients overview
Calculated coefficients Calculated coefficients
A0 B1 E-3

A1 B2 E-6

A2 B3 E-9

A3
A4

Diagram Absolute deviation vs. concentration

[%]

2.00

0.00

-2.00

-4.00

10.00 20.00 30.00 40.00 50.00 60.00 70.00 [%]

Concentration
Max. negative measured error
Max. positive measured error
Max. approximation error

18-02-2020 9:18 AM Page 18

 Viscosity Module

Calculation model
Compensation coefficient X1 NaN
Compensation coefficient X2 NaN
Reference temperature NaN °C
Temperature unit °C
Dynamic viscosity unit/ cP
Kinematic viscosity unit

Diagram measured viscosity vs. temperature

[cP]

0.40

0.30

0.20

0.10

0.00
10.00 20.00 30.00 40.00 50.00 60.00 70.00 [°C]

measured viscosity.
temperature corrected viscosity
reference point

18-02-2020 9:18 AM Page 19