Max232 PDF
Max232 PDF
Max232 PDF
MAX220–MAX249
The MAX220–MAX249 family of line drivers/receivers is Superior to Bipolar
intended for all EIA/TIA-232E and V.28/V.24 communica- ♦ Operate from Single +5V Power Supply
tions interfaces, particularly applications where ±12V is
(+5V and +12V—MAX231/MAX239)
not available.
♦ Low-Power Receive Mode in Shutdown
These parts are especially useful in battery-powered sys-
(MAX223/MAX242)
tems, since their low-power shutdown mode reduces
power dissipation to less than 5µW. The MAX225, ♦ Meet All EIA/TIA-232E and V.28 Specifications
MAX233, MAX235, and MAX245/MAX246/MAX247 use ♦ Multiple Drivers and Receivers
no external components and are recommended for appli- ♦ 3-State Driver and Receiver Outputs
cations where printed circuit board space is critical. ♦ Open-Line Detection (MAX243)
Selection Table
Power No. of Nominal SHDN Rx
Part Supply RS-232 No. of Cap. Value & Three- Active in Data Rate
Number (V) Drivers/Rx Ext. Caps (µF) State SHDN (kbps) Features
MAX220 +5 2/2 4 4.7/10 No — 120 Ultra-low-power, industry-standard pinout
MAX222 +5 2/2 4 0.1 Yes — 200 Low-power shutdown
MAX223 (MAX213) +5 4/5 4 1.0 (0.1) Yes ✔ 120 MAX241 and receivers active in shutdown
MAX225 +5 5/5 0 — Yes ✔ 120 Available in SO
MAX230 (MAX200) +5 5/0 4 1.0 (0.1) Yes — 120 5 drivers with shutdown
MAX231 (MAX201) +5 and 2/2 2 1.0 (0.1) No — 120 Standard +5/+12V or battery supplies;
+7.5 to +13.2 same functions as MAX232
MAX232 (MAX202) +5 2/2 4 1.0 (0.1) No — 120 (64) Industry standard
MAX232A +5 2/2 4 0.1 No — 200 Higher slew rate, small caps
MAX233 (MAX203) +5 2/2 0 — No — 120 No external caps
MAX233A +5 2/2 0 — No — 200 No external caps, high slew rate
MAX234 (MAX204) +5 4/0 4 1.0 (0.1) No — 120 Replaces 1488
MAX235 (MAX205) +5 5/5 0 — Yes — 120 No external caps
MAX236 (MAX206) +5 4/3 4 1.0 (0.1) Yes — 120 Shutdown, three state
MAX237 (MAX207) +5 5/3 4 1.0 (0.1) No — 120 Complements IBM PC serial port
MAX238 (MAX208) +5 4/4 4 1.0 (0.1) No — 120 Replaces 1488 and 1489
MAX239 (MAX209) +5 and 3/5 2 1.0 (0.1) No — 120 Standard +5/+12V or battery supplies;
+7.5 to +13.2 single-package solution for IBM PC serial port
MAX240 +5 5/5 4 1.0 Yes — 120 DIP or flatpack package
MAX241 (MAX211) +5 4/5 4 1.0 (0.1) Yes — 120 Complete IBM PC serial port
MAX242 +5 2/2 4 0.1 Yes ✔ 200 Separate shutdown and enable
MAX243 +5 2/2 4 0.1 No — 200 Open-line detection simplifies cabling
MAX244 +5 8/10 4 1.0 No — 120 High slew rate
MAX245 +5 8/10 0 — Yes ✔ 120 High slew rate, int. caps, two shutdown modes
MAX246 +5 8/10 0 — Yes ✔ 120 High slew rate, int. caps, three shutdown modes
MAX247 +5 8/9 0 — Yes ✔ 120 High slew rate, int. caps, nine operating modes
MAX248 +5 8/8 4 1.0 Yes ✔ 120 High slew rate, selective half-chip enables
MAX249 +5 6/10 4 1.0 Yes ✔ 120 Available in quad flatpack package
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ABSOLUTE MAXIMUM RATINGS—MAX220/222/232A/233A/242/243
MAX220–MAX249
Supply Voltage (VCC) ...............................................-0.3V to +6V 16-Pin Narrow SO (derate 8.70mW/°C above +70°C) ...696mW
Input Voltages 16-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW
TIN..............................................................-0.3V to (VCC - 0.3V) 18-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW
RIN .....................................................................................±30V 20-Pin Wide SO (derate 10.00mW/°C above +70°C)....800mW
TOUT (Note 1).....................................................................±15V 20-Pin SSOP (derate 8.00mW/°C above +70°C) ..........640mW
Output Voltages 16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW
TOUT ...................................................................................±15V 18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW
ROUT .........................................................-0.3V to (VCC + 0.3V) Operating Temperature Ranges
Driver/Receiver Output Short Circuited to GND.........Continuous MAX2_ _AC_ _, MAX2_ _C_ _ .............................0°C to +70°C
Continuous Power Dissipation (TA = +70°C) MAX2_ _AE_ _, MAX2_ _E_ _ ..........................-40°C to +85°C
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW MAX2_ _AM_ _, MAX2_ _M_ _ .......................-55°C to +125°C
18-Pin Plastic DIP (derate 11.11mW/°C above +70°C)....889mW Storage Temperature Range .............................-65°C to +160°C
20-Pin Plastic DIP (derate 8.00mW/°C above +70°C) ....440mW Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Input voltage measured with TOUT in high-impedance state, SHDN or VCC = 0V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243
(VCC = +5V ±10%, C1–C4 = 0.1µF‚ TA = TMIN to TMAX‚ unless otherwise noted.)
2 _______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243 (continued)
MAX220–MAX249
(VCC = +5V ±10%, C1–C4 = 0.1µF‚ TA = TMIN to TMAX‚ unless otherwise noted.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
EN Input Threshold Low MAX242 1.4 0.8 V
EN Input Threshold High MAX242 2.0 1.4 V
CL = 50pF to 2500pF,
RL = 3kΩ to 7kΩ, MAX222/232A/233A/242/243 6 12 30
Transition Slew Rate VCC = 5V, TA = +25°C, V/µs
measured from +3V MAX220 1.5 3 30
to -3V or -3V to +3V
MAX222/232A/233A/242/243 1.3 3.5
Transmitter Propagation Delay tPHLT
MAX220 4 10
TLL to RS-232 (normal operation), µs
Figure 1 MAX222/232A/233A/242/243 1.5 3.5
tPLHT
MAX220 5 10
MAX222/232A/233A/242/243 0.5 1
Receiver Propagation Delay tPHLR
MAX220 0.6 3
RS-232 to TLL (normal operation), µs
Figure 2 MAX222/232A/233A/242/243 0.6 1
tPLHR
MAX220 0.8 3
Receiver Propagation Delay tPHLS MAX242 0.5 10
µs
RS-232 to TLL (shutdown), Figure 2 tPLHS MAX242 2.5 10
Receiver-Output Enable Time, Figure 3 tER MAX242 125 500 ns
Receiver-Output Disable Time, Figure 3 tDR MAX242 160 500 ns
Transmitter-Output Enable Time MAX222/242, 0.1µF caps
tET 250 µs
(SHDN goes high), Figure 4 (includes charge-pump start-up)
Transmitter-Output Disable Time
tDT MAX222/242, 0.1µF caps 600 ns
(SHDN goes low), Figure 4
Transmitter + to - Propagation MAX222/232A/233A/242/243 300
tPHLT - tPLHT ns
Delay Difference (normal operation) MAX220 2000
Receiver + to - Propagation MAX222/232A/233A/242/243 100
tPHLR - tPLHR ns
Delay Difference (normal operation) MAX220 225
Note 2: MAX243 R2OUT is guaranteed to be low when R2IN is ≥ 0V or is floating.
_______________________________________________________________________________________ 3
+5V-Powered, Multichannel RS-232
Drivers/Receivers
__________________________________________Typical Operating Characteristics
MAX220–MAX249
MAX220/MAX222/MAX232A/MAX233A/MAX242/MAX243
AVAILABLE OUTPUT CURRENT MAX222/MAX242
OUTPUT VOLTAGE vs. LOAD CURRENT vs. DATA RATE ON-TIME EXITING SHUTDOWN
10 11 +10V
MAX220-01
MAX220-02
MAX220-03
1µF V+
8 OUTPUT LOAD CURRENT 1µF CAPS
10 FLOWS FROM V+ TO V-
6 EITHER V+ OR V- LOADED V+
0.1µF CAPS
ALL CAPS +5V
OUTPUT CURRENT (mA)
VCC = ±5V 0.1µF
OUTPUT VOLTAGE (V)
4 9 1µF +5V
4 _______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ABSOLUTE MAXIMUM RATINGS—MAX223/MAX230–MAX241
MAX220–MAX249
VCC ...........................................................................-0.3V to +6V 20-Pin Wide SO (derate 10 00mW/°C above +70°C).......800mW
V+ ................................................................(VCC - 0.3V) to +14V 24-Pin Wide SO (derate 11.76mW/°C above +70°C).......941mW
V- ............................................................................+0.3V to -14V 28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W
Input Voltages 44-Pin Plastic FP (derate 11.11mW/°C above +70°C) .....889mW
TIN ............................................................-0.3V to (VCC + 0.3V) 14-Pin CERDIP (derate 9.09mW/°C above +70°C) ..........727mW
RIN......................................................................................±30V 16-Pin CERDIP (derate 10.00mW/°C above +70°C) ........800mW
Output Voltages 20-Pin CERDIP (derate 11.11mW/°C above +70°C) ........889mW
TOUT ...................................................(V+ + 0.3V) to (V- - 0.3V) 24-Pin Narrow CERDIP
ROUT .........................................................-0.3V to (VCC + 0.3V) (derate 12.50mW/°C above +70°C) ..............1W
Short-Circuit Duration, TOUT ......................................Continuous 24-Pin Sidebraze (derate 20.0mW/°C above +70°C)..........1.6W
Continuous Power Dissipation (TA = +70°C) 28-Pin SSOP (derate 9.52mW/°C above +70°C).............762mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW Operating Temperature Ranges
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW MAX2 _ _ C _ _......................................................0°C to +70°C
20-Pin Plastic DIP (derate 11.11mW/°C above +70°C)....889mW MAX2 _ _ E _ _ ...................................................-40°C to +85°C
24-Pin Narrow Plastic DIP MAX2 _ _ M _ _ ...............................................-55°C to +125°C
(derate 13.33mW/°C above +70°C) ..........1.07W Storage Temperature Range .............................-65°C to +160°C
24-Pin Plastic DIP (derate 9.09mW/°C above +70°C)......500mW Lead Temperature (soldering, 10sec) .............................+300°C
16-Pin Wide SO (derate 9.52mW/°C above +70°C).........762mW
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241
(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10; MAX233/MAX235, VCC = 5V ±5%‚ C1–C4 = 1.0µF; MAX231/MAX239,
VCC = 5V ±10%; V+ = 7.5V to 13.2V; TA = TMIN to TMAX; unless otherwise noted.)
_______________________________________________________________________________________ 5
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241 (continued)
MAX220–MAX249
(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10; MAX233/MAX235, VCC = 5V ±5%‚ C1–C4 = 1.0µF; MAX231/MAX239,
VCC = 5V ±10%; V+ = 7.5V to 13.2V; TA = TMIN to TMAX; unless otherwise noted.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
Normal operation
SHDN = 5V (MAX223) 0.8 1.2
TA = +25°C, SHDN = 0V (MAX235/236/240/241)
RS-232 Input Threshold Low V
VCC = 5V Shutdown (MAX223)
SHDN = 0V, 0.6 1.5
EN = 5V (R4IN, R5IN)
Normal operation
SHDN = 5V (MAX223) 1.7 2.4
TA = +25°C, SHDN = 0V (MAX235/236/240/241)
RS-232 Input Threshold High V
VCC = 5V Shutdown (MAX223)
SHDN = 0V, 1.5 2.4
EN = 5V (R4IN‚ R5IN)
RS-232 Input Hysteresis VCC = 5V, no hysteresis in shutdown 0.2 0.5 1.0 V
RS-232 Input Resistance TA = +25°C, VCC = 5V 3 5 7 kΩ
TTL/CMOS Output Voltage Low IOUT = 1.6mA (MAX231/232/233, IOUT = 3.2mA) 0.4 V
TTL/CMOS Output Voltage High IOUT = -1mA 3.5 VCC - 0.4 V
0V ≤ ROUT ≤ VCC; EN = 0V (MAX223);
TTL/CMOS Output Leakage Current 0.05 ±10 µA
EN = VCC (MAX235–241 )
6 _______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
__________________________________________Typical Operating Characteristics
MAX220–MAX249
MAX223/MAX230–MAX241
TRANSMITTER OUTPUT VOLTAGE (VOH)
TRANSMITTER OUTPUT vs. LOAD CAPACITANCE AT TRANSMITTER SLEW RATE
VOLTAGE (VOH) vs. VCC DIFFERENT DATA RATES vs. LOAD CAPACITANCE
8.5 7.4 12.0
MAX220-04
MAX220-06
MAX220-05
1 TRANSMITTER LOADED TA = +25°C
2 TRANSMITTERS
LOADED 7.2 11.0 VCC = +5V
LOADED, RL = 3kΩ
8.0 10.0 C1–C4 = 1µF
7.0
6.8
VOH (V)
MAX220-09
MAX220-08
MAX220-07
V- LOADED,
VOL (V)
VOL (V)
V+ AND V- V+ LOADED,
160kbits/sec NO LOAD
-7.5 -6.8 0 EQUALLY
80kbits/sec ON V+ NO LOAD
1 TRANS- -2 LOADED ON V-
-7.0 20Kkbits/sec
-8.0 MITTER
LOADED -4
-7.2
2 TRANS- 3 TRANS- -6
-8.5
MITTERS MITTERS -7.4
-8
LOADED LOADED ALL TRANSMITTERS UNLOADED
-9.0 -7.6 -10
4.5 5.0 5.5 0 500 1000 1500 2000 2500 0 5 10 15 20 25 30 35 40 45 50
VCC (V) LOAD CAPACITANCE (pF) CURRENT (mA)
V+
V-
SHDN*
500ms/div
*SHUTDOWN POLARITY IS REVERSED
FOR NON MAX241 PARTS
_______________________________________________________________________________________ 7
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ABSOLUTE MAXIMUM RATINGS—MAX225/MAX244–MAX249
MAX220–MAX249
Supply Voltage (VCC) ...............................................-0.3V to +6V Continuous Power Dissipation (TA = +70°C)
Input Voltages 28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W
TIN‚ ENA, ENB, ENR, ENT, ENRA, 40-Pin Plastic DIP (derate 11.11mW/°C above +70°C) ...611mW
ENRB, ENTA, ENTB..................................-0.3V to (VCC + 0.3V) 44-Pin PLCC (derate 13.33mW/°C above +70°C) ...........1.07W
RIN .....................................................................................±25V Operating Temperature Ranges
TOUT (Note 3).....................................................................±15V MAX225C_ _, MAX24_C_ _ ..................................0°C to +70°C
ROUT ........................................................-0.3V to (VCC + 0.3V) MAX225E_ _, MAX24_E_ _ ...............................-40°C to +85°C
Short Circuit (one output at a time) Storage Temperature Range .............................-65°C to +160°C
TOUT to GND ............................................................Continuous Lead Temperature (soldering,10sec) ..............................+300°C
ROUT to GND............................................................Continuous
Note 3: Input voltage measured with transmitter output in a high-impedance state, shutdown, or VCC = 0V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249
(MAX225, VCC = 5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA = TMIN to TMAX; unless oth-
erwise noted.)
8 _______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249 (continued)
MAX220–MAX249
(MAX225, VCC = 5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA = TMIN to TMAX; unless oth-
erwise noted.)
PARAMETER CONDITIONS MIN TYP MAX UNITS
POWER SUPPLY AND CONTROL LOGIC
MAX225 4.75 5.25
Operating Supply Voltage V
MAX244–MAX249 4.5 5.5
MAX225 10 20
No load
VCC Supply Current MAX244–MAX249 11 30
mA
(normal operation) 3kΩ loads on MAX225 40
all outputs MAX244–MAX249 57
TA = +25°C 8 25
Shutdown Supply Current µA
TA = TMIN to TMAX 50
Leakage current ±1 µA
Control Input Threshold low 1.4 0.8
V
Threshold high 2.4 1.4
AC CHARACTERISTICS
CL = 50pF to 2500pF, RL = 3kΩ to 7kΩ, VCC = 5V,
Transition Slew Rate 5 10 30 V/µs
TA = +25°C, measured from +3V to -3V or -3V to +3V
Transmitter + to - Propagation
tPHLT - tPLHT 350 ns
Delay Difference (normal operation)
Receiver + to - Propagation
tPHLR - tPLHR 350 ns
Delay Difference (normal operation)
Receiver-Output Enable Time, Figure 3 tER 100 500 ns
Receiver-Output Disable Time, Figure 3 tDR 100 500 ns
MAX246–MAX249
5 µs
(excludes charge-pump start-up)
Transmitter Enable Time tET
MAX225/MAX245–MAX249
10 ms
(includes charge-pump start-up)
Transmitter Disable Time, Figure 4 tDT 100 ns
Note 4: The 300Ω minimum specification complies with EIA/TIA-232E, but the actual resistance when in shutdown mode or VCC =
0V is 10MΩ as is implied by the leakage specification.
_______________________________________________________________________________________ 9
+5V-Powered, Multichannel RS-232
Drivers/Receivers
__________________________________________Typical Operating Characteristics
MAX220–MAX249
MAX225/MAX244–MAX249
MAX220-11
MAX220-12
VCC = 5V VCC = 5V WITH ALL TRANSMITTERS DRIVEN
8 LOADED WITH 5kΩ
16 V+ AND V- LOADED 8.5
TRANSMITTER SLEW RATE (V/µs)
6 EITHER V+ OR 10kb/sec
14 8.0 20kb/sec
V- LOADED
OUTPUT VOLTAGE (V)
V+, V (V)
1µF CAPACITORS
10 0 8 TRANSMITTERS 7.0 60kb/sec
40kb/s DATA RATE DRIVING 5kΩ AND
8 8 TRANSMITTERS -2
2000pF AT 20kbits/sec 6.5
LOADED WITH 3kΩ -4 V- LOADED
6 6.0 100kb/sec
-6 V+ AND V- LOADED
200kb/sec
4 5.5
-8
V+ LOADED ALL CAPACITIORS 1µF
2 -10 5.0
0 1 2 3 4 5 0 5 10 15 20 25 30 35 0 1 2 3 4 5
LOAD CAPACITANCE (nF) LOAD CURRENT (mA) LOAD CAPACITANCE (nF)
10 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+3V
0V* 50% 50%
+3V INPUT
INPUT
0V
VCC
OUTPUT 50% 50%
V+ GND
0V
OUTPUT
V-
tPHLR tPLHR
tPHLS tPLHS
tPLHT tPHLT
EN
RX OUT 1k
RX IN RX VCC - 2V +3V
SHDN
a) TEST CIRCUIT 0V
150pF
OUTPUT DISABLE TIME (tDT)
+3V
EN INPUT V+
0V +5V
EN
OUTPUT ENABLE TIME (tER) 0V
-5V
+3.5V
V-
RECEIVER
OUTPUTS
+0.8V
a) TIMING DIAGRAM
b) ENABLE TIMING
+3V
EN
0V 1 OR 0 TX
EN INPUT
OUTPUT DISABLE TIME (tDR) 3k 50pF
VOH
VOH - 0.5V
RECEIVER VCC - 2V
OUTPUTS
VOL + 0.5V b) TEST CIRCUIT
VOL
c) DISABLE TIMING
Figure 3. Receiver-Output Enable and Disable Timing Figure 4. Transmitter-Output Disable Timing
______________________________________________________________________________________ 11
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Table 1a. MAX245 Control Pin Configurations
MAX220–MAX249
RA1–RA4 3-State,
1 0 Shutdown All 3-State All Active All Active
RA5 Active
12 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Table 1d. MAX247/MAX248/MAX249 Control Pin Configurations
MAX220–MAX249
TRANSMITTERS RECEIVERS
OPERATION MAX247 TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB5
ENTA ENTB ENRA ENRB
STATUS MAX248 TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB4
MAX249 TA1–TA3 TB1–TB3 RA1–RA5 RB1–RB5
0 0 0 0 Normal Operation All Active All Active All Active All Active
All 3-State, except
0 0 0 1 Normal Operation All Active All Active All Active RB5 stays active on
MAX247
0 0 1 0 Normal Operation All Active All Active All 3-State All Active
All 3-State, except
0 0 1 1 Normal Operation All Active All Active All 3-State RB5 stays active on
MAX247
0 1 0 0 Normal Operation All Active All 3-State All Active All Active
All 3-State, except
0 1 0 1 Normal Operation All Active All 3-State All Active RB5 stays active on
MAX247
0 1 1 0 Normal Operation All Active All 3-State All 3-State All Active
All 3-State, except
0 1 1 1 Normal Operation All Active All 3-State All 3-State B5 stays active on
MAX247
1 0 0 0 Normal Operation All 3-State All Active All Active All Active
All 3-State, except
1 0 0 1 Normal Operation All 3-State All Active All Active RB5 stays active on
MAX247
1 0 1 0 Normal Operation All 3-State All Active All 3-State All Active
All 3-State, except
1 0 1 1 Normal Operation All 3-State All Active All 3-State RB5 stays active on
MAX247
Low-Power Low-Power
1 1 0 0 Shutdown All 3-State All 3-State
Receive Mode Receive Mode
Low-Power
1 1 1 0 Shutdown All 3-State All 3-State All 3-State
Receive Mode
______________________________________________________________________________________ 13
+5V-Powered, Multichannel RS-232
Drivers/Receivers
_______________Detailed Description when device power is removed. Outputs can be driven
MAX220–MAX249
14 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
The receiver input hysteresis is typically 0.5V with a Shutdown—MAX222–MAX242
MAX220–MAX249
guaranteed minimum of 0.2V. This produces clear out- On the MAX222‚ MAX235‚ MAX236‚ MAX240‚ and
put transitions with slow-moving input signals, even MAX241‚ all receivers are disabled during shutdown.
with moderate amounts of noise and ringing. The On the MAX223 and MAX242‚ two receivers continue to
receiver propagation delay is typically 600ns and is operate in a reduced power mode when the chip is in
independent of input swing direction. shutdown. Under these conditions‚ the propagation
delay increases to about 2.5µs for a high-to-low input
Low-Power Receive Mode transition. When in shutdown, the receiver acts as a
The low-power receive-mode feature of the MAX223, CMOS inverter with no hysteresis. The MAX223 and
MAX242, and MAX245–MAX249 puts the IC into shut- MAX242 also have a receiver output enable input (EN
down mode but still allows it to receive information. This for the MAX242 and EN for the MAX223) that allows
is important for applications where systems are periodi- receiver output control independent of SHDN (SHDN
cally awakened to look for activity. Using low-power for MAX241). With all other devices‚ SHDN (SHDN for
receive mode, the system can still receive a signal that MAX241) also disables the receiver outputs.
will activate it on command and prepare it for communi-
cation at faster data rates. This operation conserves The MAX225 provides five transmitters and five
system power. receivers‚ while the MAX245 provides ten receivers and
eight transmitters. Both devices have separate receiver
Negative Threshold—MAX243 and transmitter-enable controls. The charge pumps
The MAX243 is pin compatible with the MAX232A, differ- turn off and the devices shut down when a logic high is
ing only in that RS-232 cable fault protection is removed applied to the ENT input. In this state, the supply cur-
on one of the two receiver inputs. This means that control rent drops to less than 25µA and the receivers continue
lines such as CTS and RTS can either be driven or left to operate in a low-power receive mode. Driver outputs
floating without interrupting communication. Different enter a high-impedance state (three-state mode). On
cables are not needed to interface with different pieces of the MAX225‚ all five receivers are controlled by the
equipment. ENR input. On the MAX245‚ eight of the receiver out-
The input threshold of the receiver without cable fault puts are controlled by the ENR input‚ while the remain-
protection is -0.8V rather than +1.4V. Its output goes ing two receivers (RA5 and RB5) are always active.
positive only if the input is connected to a control line RA1–RA4 and RB1–RB4 are put in a three-state mode
that is actively driven negative. If not driven, it defaults when ENR is a logic high.
to the 0 or “OK to send” state. Normally‚ the MAX243’s Receiver and Transmitter Enable
other receiver (+1.4V threshold) is used for the data line Control Inputs
(TD or RD)‚ while the negative threshold receiver is con- The MAX225 and MAX245–MAX249 feature transmitter
nected to the control line (DTR‚ DTS‚ CTS‚ RTS, etc.). and receiver enable controls.
Other members of the RS-232 family implement the The receivers have three modes of operation: full-speed
optional cable fault protection as specified by EIA/TIA- receive (normal active)‚ three-state (disabled)‚ and low-
232E specifications. This means a receiver output goes power receive (enabled receivers continue to function
high whenever its input is driven negative‚ left floating‚ at lower data rates). The receiver enable inputs control
or shorted to ground. The high output tells the serial the full-speed receive and three-state modes. The
communications IC to stop sending data. To avoid this‚ transmitters have two modes of operation: full-speed
the control lines must either be driven or connected transmit (normal active) and three-state (disabled). The
with jumpers to an appropriate positive voltage level. transmitter enable inputs also control the shutdown
mode. The device enters shutdown mode when all
transmitters are disabled. Enabled receivers function in
the low-power receive mode when in shutdown.
______________________________________________________________________________________ 15
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Tables 1a–1d define the control states. The MAX244 The MAX249 provides ten receivers and six drivers with
MAX220–MAX249
has no control pins and is not included in these tables. four control pins. The ENRA and ENRB receiver enable
The MAX246 has ten receivers and eight drivers with inputs each control five receiver outputs. The ENTA
two control pins, each controlling one side of the and ENTB transmitter enable inputs control three dri-
device. A logic high at the A-side control input (ENA) vers each. There is no always-active receiver. The
causes the four A-side receivers and drivers to go into device enters shutdown mode and transmitters go into
a three-state mode. Similarly, the B-side control input a three-state mode with a logic high on both ENTA and
(ENB) causes the four B-side drivers and receivers to ENTB. In shutdown mode, active receivers operate in a
go into a three-state mode. As in the MAX245, one A- low-power receive mode at data rates up to
side and one B-side receiver (RA5 and RB5) remain 20kbits/sec.
active at all times. The entire device is put into shut- __________Applications Information
down mode when both the A and B sides are disabled
(ENA = ENB = +5V). Figures 5 through 25 show pin configurations and typi-
cal operating circuits. In applications that are sensitive
The MAX247 provides nine receivers and eight drivers to power-supply noise, VCC should be decoupled to
with four control pins. The ENRA and ENRB receiver ground with a capacitor of the same value as C1 and
enable inputs each control four receiver outputs. The C2 connected as close as possible to the device.
ENTA and ENTB transmitter enable inputs each control
four drivers. The ninth receiver (RB5) is always active.
The device enters shutdown mode with a logic high on
both ENTA and ENTB.
The MAX248 provides eight receivers and eight drivers
with four control pins. The ENRA and ENRB receiver
enable inputs each control four receiver outputs. The
ENTA and ENTB transmitter enable inputs control four
drivers each. This part does not have an always-active
receiver. The device enters shutdown mode and trans-
mitters go into a three-state mode with a logic high on
both ENTA and ENTB.
16 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V INPUT C3
TOP VIEW
C5
16
1 VCC
C1+ 1 16 VCC C1+ V+ 2 +10V
C1 +5V TO +10V
V+ 2 3 C1-
15 GND VOLTAGE DOUBLER
4
C1- 3 C2+ +10V TO -10V 6 -10V
14 T1OUT C2 5 C2- VOLTAGE INVERTER
V-
C4
C2+ 4 MAX220 13 R1IN
+5V
MAX232
C2- 5 MAX232A 12 R1OUT 400k
V- 6 11 T1IN T1OUT 14
11 T1IN
+5V
T2OUT 7 10 T2IN TTL/CMOS RS-232
INPUTS 400k OUTPUTS
R2IN 8 9 R2OUT 10 T2IN T2OUT 7
GND
15
+5V INPUT C3
TOP VIEW ALL CAPACITORS = 0.1µF
C5
17
2 VCC 3 +10V
C1+ +5V TO +10V
C1 V+
(N.C.) EN 1 4 C1- VOLTAGE DOUBLER
20 SHDN
5
(N.C.) EN 1 C1+ 2 C2+ 7 -10V
18 SHDN 19 VCC
C2 +10V TO -10V V-
6 C2- C4
VOLTAGE INVERTER
C1+ 2 17 VCC V+ 3 18 GND
V+ 3 C1- 4 +5V
16 GND 17 T1OUT
400k
C1- 4 15 T1OUT C2+ 5 MAX222 16 N.C.
MAX242 12 T1IN T1OUT 15
C2+ 5 MAX222 14 R1IN C2- 6 15 R1IN +5V
MAX242 TTL/CMOS RS-232
C2- 6 13 R1OUT V- 7 14 R1OUT INPUTS 400k OUTPUTS
11 T2IN T2OUT 8
V- 7 12 T1IN T2OUT 8 13 N.C.
T2OUT 8 11 T2IN R2IN 9 12 T1IN 13 R1OUT R1IN 14
R2IN 9 10 R2OUT R2OUT 10 11 T2IN
TTL/CMOS 5k RS-232
OUTPUTS INPUTS
DIP/SO 10 R2OUT R2IN 9
SSOP
1 (N.C.) EN 5k
( ) ARE FOR MAX222 ONLY. 18
GND SHDN
PIN NUMBERS IN TYPICAL OPERATING CIRCUIT ARE FOR DIP/SO PACKAGES ONLY.
16
______________________________________________________________________________________ 17
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW
0.1
28 27
+5V VCC VCC
400k
T1IN
3 11
ENR 1 +5V T1OUT
28 VCC
400k
ENR 2 27 VCC
T2IN
T1IN 3 4 12
26 ENT +5V T2OUT
T2IN 4 25 T3IN 400k
R1OUT 5 MAX225 24 T4IN T3IN
25 18
+5V T3OUT
R2OUT 6 23 T5IN
400k
R3OUT 7 22 R4OUT
T4IN
24 17
R3IN 8 21 R5OUT +5V T4OUT
R2IN 9 20 R5IN 400k
T5IN T5OUT
R1IN 10 19 R4IN 23 16
T1OUT 11 18 T3OUT ENT
26 15
T2OUT 12 17 T4OUT T5OUT
SO R2OUT R2IN
6 9
5k
R3OUT R3IN
7 8
MAX225 FUNCTIONAL DESCRIPTION
5k
5 RECEIVERS
5 TRANSMITTERS R4OUT R4IN
22 19
2 CONTROL PINS
1 RECEIVER ENABLE (ENR) 5k
1 TRANSMITTER ENABLE (ENT)
R5OUT R5IN
21 20
5k
1 ENR
2 ENR
PINS (ENR, GND, VCC, T5OUT) ARE INTERNALLY CONNECTED. GND GND
CONNECT EITHER OR BOTH EXTERNALLY. T5OUT IS A SINGLE DRIVER. 13 14
18 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V INPUT
TOP VIEW 1.0µF
11
12 1.0µF
C1+ VCC 13
1.0µF 14 +5V TO +10V V+
C1- VOLTAGE DOUBLER
15
C2+ +10V TO -10V 17
1.0µF VOLTAGE INVERTER V-
16 C2-
1.0µF
+5V
400k
7 T1IN T1OUT 2
T1
GND 10 19 R5OUT*
8 R1OUT R1IN 9
VCC 11 18 R5IN* R1
5k
C1+ 12 17 V-
V+ 13 16 C2- R2IN 4
5 R2OUT
R2
C1- 14 15 C2+
5k
Wide SO/
SSOP LOGIC 26 R3OUT R3IN 27 RS-232
R3
OUTPUTS INPUTS
5k
22 R4OUT R4IN 23
R4
5k
19 R5OUT R5IN 18
R5
*R4 AND R5 IN MAX223 REMAIN ACTIVE IN SHUTDOWN 5k
NOTE: PIN LABELS IN ( ) ARE FOR MAX241 24 EN (EN) SHDN 25
(SHDN)
GND
10
______________________________________________________________________________________ 19
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
7 1.0µF
8 C1+ VCC
V+ 9
1.0µF 10 C1- +5V TO +10V
VOLTAGE DOUBLER
T3OUT 1 20 T4OUT 11
C2+ +10V TO -10V 13
T1OUT 2 19 T5IN 1.0µF 12 V-
C2- VOLTAGE INVERTER
1.0µF
T2OUT 3 18 N.C. +5V
400kΩ
T2IN 4 17 SHDN 5 T1IN T1OUT 2
T1 T1
T1IN 5 MAX230 16 T5OUT +5V
400kΩ
GND 6 15 T4IN 4 T2IN T2OUT 3
T2
VCC 7 14 T3IN +5V
400kΩ
C1+ 8 13 V-
TTL/CMOS 14 T3IN T3OUT 1 RS-232
T3
V+ 9 12 C2- INPUTS +5V OUTPUTS
400kΩ
C1- 10 11 C2+ 15 T4IN T4OUT 20
T4
+5V
400kΩ
DIP/SO 19 T5IN T5OUT 16
T5
N.C. x 18 GND
17 SHDN
6
+5V INPUT
TOP VIEW 1.0µF +7.5V TO +12V
13 (15)
1 VCC 14 (16)
C1+ V+
1.0µF 2 +12V TO -12V 3
C1- VOLTAGE CONVERTER V-
C2
+5V 1.0µF
C+ 1 14 V+ C+ 1 16 V+
400kΩ
C- 2 13 VCC C- 2 15 VCC (10) (13)
8 T1IN T1OUT 11
T1
V- 3 12 GND V- 3 14 GND
+5V
TTL/CMOS RS-232
T2OUT 4 MAX231 11 T1OUT T2OUT 4 MAX231 13 T1OUT INPUTS 400kΩ OUTPUTS
R2IN 5 10 R1IN R2IN 5 12 R1IN 7 T2IN T2OUT 4
T2
R2OUT 6 9 R1OUT R2OUT 6 11 R1OUT
(11) (12)
9 R1OUT R1IN 10
T2IN 7 8 T1IN T2IN 7 10 T1IN R1
GND
PIN NUMBERS IN ( ) ARE FOR SO PACKAGE 12 (14)
20 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V INPUT
1.0µF
TOP VIEW
7
+5V VCC
400k
2 T1IN T1OUT 5
T2IN 1 20 R2OUT
+5V
T1IN 2 19 R2IN TTL/CMOS RS-232
400k
INPUTS OUTPUTS
R1OUT 3 18 T2OUT 1 T2IN T2OUT 18
R1IN 4 17 V-
3 R1OUT R1IN 4
T1OUT 5 MAX233 16 C2-
MAX233A
GND 6 15 C2+ TTL/CMOS 5k RS-232
OUTPUTS OUTPUTS
VCC 7 14 V+ (C1-)
(V+) C1+ 8 13 C1- (C1+) 20 R2OUT R2IN 19
+5V INPUT
TOP VIEW 1.0µF
6 1.0µF
7
C1+ VCC 8
+5V TO +10V V+
1.0µF 9
C1- VOLTAGE DOUBLER
10
C2+ +10V TO -10V 12
1.0µF VOLTAGE INVERTER V-
T1OUT 1 11 C2-
16 T3OUT 1.0µF
+5V
T2OUT 2 15 T4OUT
400k
T2IN 3 14 T4IN
4 T1IN T1OUT 1
T1
T1IN 4 MAX234 13 T3IN +5V
GND 5 12 V- 400k
VCC 6 11 C2- 3 T2IN T2OUT 3
T2
C1+ 7 +5V RS-232
10 C2+ TTL/CMOS
INPUTS 400k OUTPUTS
V+ 8 9 C1-
13 T3IN T3OUT 16
T3
+5V
DIP/SO
400k
14 T4IN T4OUT 15
T4
GND
5
______________________________________________________________________________________ 21
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V INPUT
TOP VIEW 1.0µF
12
VCC
+5V
400k
8 T1IN T1OUT 3
T1
+5V
400k
7 T2IN T2OUT 4
T2
+5V
400k
TTL/CMOS 15 T3IN T3OUT 2 RS-232
T3
INPUTS OUTPUTS
T4OUT 1 24 R3IN +5V
400k
T3OUT 2 23 R3OUT T4OUT 1
16 T4IN
T4
T1OUT 3 22 T5IN
+5V
T2OUT 4 21 SHDN 400k
R2IN 5 MAX235 20 EN 22 T5IN T5OUT 19
T5
R2OUT 6 19 T5OUT
T2IN 7 18 R4IN
9 R1OUT R1IN 10
T1
T1IN 8 17 R4OUT
5k
R1OUT 9 16 T4IN
17 R4OUT R4IN 18
R4
5k
14 R5OUT R5IN 13
R5
5k
20 EN 21
SHDN
GND
11
22 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
TOP VIEW +5V INPUT
1.0µF
9 1.0µF
10 11
C1+ VCC V+
1.0µF +5V TO +10V
12
C1- VOLTAGE DOUBLER
13 15
C2+ V-
1.0µF +10V TO -10V
14 C2- 1.0µF
VOLTAGE INVERTER
+5V
400k
7 T1IN T1OUT 2
T1
C1+ 10 15 V-
V+ 11 14 C2- R1IN 4
5 R1OUT
R1
C1- 12 13 C2+
5k
DIP/SO
22 R2OUT R2IN 23 RS-232
TTL/CMOS R2
OUTPUTS INPUTS
5k
17 R3OUT R3IN 16
R3
5k
20 EN 21
SHDN
GND
______________________________________________________________________________________ 23
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
TOP VIEW
+5V INPUT
1.0µF
9 1.0µF
10 VCC 11
C1+ V+
+5V TO +10V
1.0µF 12 VOLTAGE DOUBLER
C1-
13 15
C2+ V-
1.0µF +10V TO -10V
14 VOLTAGE INVERTER 1.0µF
C2-
+5V
400k
5k
17 R3OUT R3IN 16
R3
5k
GND
8
24 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
TOP VIEW
+5V INPUT
1.0µF
9 1.0µF
10 VCC 11
C1+ V+
+5V TO +10V
1.0µF 12
C1- VOLTAGE DOUBLER
13
C2+ 15
1.0µF +10V TO -10V V-
14
C2- VOLTAGE INVERTER 1.0µF
+5V
400k
C1+ 10 15 V-
DIP/SO
4 R2OUT R2IN 3
R2
TTL/CMOS 5k RS-232
OUTPUTS INPUTS
22 R3OUT R3IN 23
R3
5k
17 R4OUT R4IN 16
R4
5k
GND
8
______________________________________________________________________________________ 25
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
TOP VIEW
7.5V TO 13.2V
+5V INPUT INPUT
1.0µF
4 5
6 VCC V+
C1+ 8
V-
+10V TO -10V
1.0µF 7 1.0µF
C1- VOLTAGE INVERTER
+5V
400k
24 T1IN T1OUT 19
T1
R1OUT 1 24 T1IN +5V
400k
R1IN 2 23 T2IN
TTL/CMOS 23 T2IN T2OUT 20
GND 3 22 R2OUT T2 RS-232
INPUTS OUTPUTS
VCC 4 21 R2IN +5V
400k
V+ 5 MAX239 20 T2OUT
16 T3IN T3OUT 13
C+ 6 19 T1OUT T3
C- 7 18 R3IN
DIP/SO
TTL/CMOS 17 R3OUT R3IN 18 RS-232
R3
OUTPUTS INPUTS
5k
11 R4OUT R4IN 12
R4
5k
10 R5OUT R5IN 9
R5
5k
14 EN 15
N.C.
GND
3
26 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V INPUT
TOP VIEW 1.0µF
19
25 1.0µF
C1+ VCC 26
1.0µF 27 +5V TO +10V V+
C1- VOLTAGE DOUBLER
28
C2+ +5V TO -10V 30
1.0µF VOLTAGE INVERTER V-
29 C2- 1.0µF
+5V
400k
15 T1IN T1OUT 7
T1
+5V
400k
14 T2IN T2OUT 8
T2
R3OUT
T2OUT
T1OUT
T3OUT
T4OUT
R2IN
R3IN
N.C.
N.C.
N.C.
T5IN
+5V
400k
+5V 400k
5k
OUTPUTS INPUTS
5k
Plastic FP
39 R4OUT R4IN 40
R4
5k
36 R5OUT R5IN 35
R5
5k
42 EN 43
SHDN
GND
18
______________________________________________________________________________________ 27
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
16
1
C1+ VCC
2 +10V
0.1µF +5V TO +10V V+
3 C1- VOLTAGE DOUBLER
4
C2+
C1+ 1 16 VCC +10V TO -10V 6 -10V
0.1µF 5 C2- V-
VOLTAGE INVERTER
V+ 2 15 GND 0.1µF
C1- 3 14 T1OUT +5V
V- 6 11 T1IN +5V
TTL/CMOS RS-232
T2OUT 7 10 T2IN INPUTS 400k OUTPUTS
DIP/SO
12 R1OUT R1IN 13
TTL/CMOS 5k RS-232
OUTPUTS INPUTS
9 R2OUT R2IN 8
28 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW 1µF
1µF
20
21
C1+ VCC 22
1µF
TB4OUT
TA4OUT
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
23 C1- +5V TO +10V VOLTAGE DOUBLER V+
RA4IN
RA5IN
RB5IN
24 26
C2+ V- 1µF
1µF 25 C2-
6 5 4 3 2 1 44 43 42 41 40 +10V TO -10V VOLTAGE INVERTER
2 TA1OUT +5V +5V TB1OUT 44
400k
15 TA1IN TB1IN 30
RA3IN 7 39 RB4IN
RA2IN 8 38 RB3IN +5V +5V
2 TA2OUT TB2OUT 43
RA1IN 9 37 RB2IN
400k
RA1OUT 10 36 RB1IN 16 TA2IN TB2IN 29
RA2OUT 11 35 RB1OUT
RA3OUT 12
MAX244 34 RB2OUT 3 TA3OUT +5V +5V TB3OUT 42
RA4OUT 13 33 RB3OUT 400k
RA5OUT 14 32 RB4OUT 17 TA3IN TB3IN 28
TA1IN 15 31 RB5OUT
4 TA4OUT +5V +5V TB4OUT 41
TA2IN 16 30 TB1IN
400k
TA3IN 17 29 TB2IN 18 TA4IN TB4IN 27
9 RA1IN RB1IN 36
18 19 20 21 22 23 24 25 26 27 28
TA4IN
GND
C1+
V+
C1-
C2+
C2-
V-
TB4IN
TB3IN
VCC
5k 5k
5k 5k
MAX249 FUNCTIONAL DESCRIPTION
10 RECEIVERS 11 RA2OUT RB2OUT 34
5 A-SIDE RECEIVER 7 RA3IN RB3IN 38
5 B-SIDE RECEIVER
8 TRANSMITTERS 5k 5k
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS 12 RA3OUT RB3OUT 33
NO CONTROL PINS 6 RA4IN RB4IN 39
5k 5k
13 RA4OUT RB4OUT 32
5 RA5IN RB5IN 40
5k 5k
14 RA5OUT RB5OUT 31
GND
19
______________________________________________________________________________________ 29
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW
1µF
40
VCC
ENR 1 40 VCC 16 TA1OUT +5V +5V TB1OUT 24
400k
TA1IN 2 39 ENT
2 TA1IN TB1IN 38
TA2IN 3 38 TB1IN
17 TA2OUT +5V +5V TB2OUT 23
TA3IN 4 37 TB2IN
400k
TA4IN 5 36 TB3IN
3 TA2IN TB2IN 37
RA5OUT 6 35 TB4IN
RA4OUT 7
MAX245 34 RB5OUT 18 TA3OUT +5V +5V TB3OUT 22
400k
RA3OUT 8 33 RB4OUT
4 TA3IN TB3IN 36
RA2OUT 9 32 RB3OUT
19 TA4OUT +5V +5V TB4OUT 21
RA1OUT 10 31 RB2OUT
400k
RA1IN 11 30 RB1OUT 5 TA4IN TB4IN 35
RA2IN 12 29 RB1IN
1 ENR ENT 39
RA3IN 13 28 RB2IN
11 RA1IN RB1IN 29
RA4IN 14 27 RB3IN
RA5IN 15 26 RB4IN
5k 5k
TA1OUT 16 25 RB5IN
TA4OUT 19 22 TB3OUT
5k 5k
GND 20 21 TB4OUT
9 RA2OUT RB2OUT 31
DIP 13 RA3IN RB3IN 27
5k 5k
8 RA3OUT RB3OUT 32
MAX245 FUNCTIONAL DESCRIPTION
14 RA4IN RB4IN 26
10 RECEIVERS
5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE)
5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE) 5k 5k
8 TRANSMITTTERS
7 RA4OUT RB4OUT 33
4 A-SIDE TRANSMITTERS
15 RA5IN RB5IN 25
2 CONTROL PINS
1 RECEIVER ENABLE (ENR)
5k 5k
1 TRANSMITTER ENABLE (ENT)
6 RA5OUT RB5OUT 34
GND
20
30 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW
1µF
40
VCC
ENA 1 40 VCC +5V +5V
16 TA1OUT TB1OUT 24
TA1IN 2 39 ENB
400k
TA2IN 3 38 TB1IN
2 TA1IN TB1IN 38
TA3IN 4 37 TB2IN +5V +5V
TA4IN 5 36 TB3IN 17 TA2OUT TB2OUT 23
400k
RA5OUT 6 35 TB4IN
3 TA2IN TB2IN 37
RA4OUT 7 MAX246 34 RB5OUT +5V +5V
RA3OUT 8 33 RB4OUT 18 TA3OUT TB3OUT 22
TA1OUT 16 25 RB5IN 5k 5k
TA2OUT 17 24 TB1OUT
10 RA1OUT RB1OUT 30
TA3OUT 18 23 TB2OUT
12 RA2IN RB2IN 28
TA4OUT 19 22 TB3OUT
GND 20 21 TB4OUT 5k 5k
5k 5k
MAX246 FUNCTIONAL DESCRIPTION
10 RECEIVERS 8 RA3OUT RB3OUT 32
5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE)
14 RA4IN RB4IN 26
5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)
8 TRANSMITTERS
5k 5k
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS 7 RA4OUT RB4OUT 33
2 CONTROL PINS 15 RA5IN RB5IN 25
ENABLE A-SIDE (ENA)
ENABLE B-SIDE (ENB) 5k 5k
6 RA5OUT RB5OUT 34
GND
20
______________________________________________________________________________________ 31
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW
1µF
40
1 ENTA VCC ENTB 39
ENTA 1 40 VCC +5V +5V
16 TA1OUT TB1OUT 24
TA1IN 2 39 ENTB
400k
TA2IN 3 38 TB1IN 2 TA1IN TB1IN 38
TA3IN 4 37 TB2IN +5V +5V
17 TA2OUT TB2OUT 23
TA4IN 5 36 TB3IN
400k
RB5OUT 6 35 TB4IN 3 TA2IN TB2IN 37
RA4OUT 7 MAX247 34 RB4OUT +5V +5V
18 TA3OUT TB3OUT 22
RA3OUT 8 33 RB3OUT
400k
RA2OUT 9 32 RB2OUT
4 TA3IN TB3IN 36
RA1OUT 10 31 RB1OUT +5V +5V
19 TA4OUT TB4OUT 21
ENRA 11 30 ENRB
400k
RA1IN 12 29 RB1IN
5 TA4IN TB4IN 35
RA2IN 13 28 RB2IN
6 RB5OUT RB5IN 25
RA3IN 14 27 RB3IN
RA4IN 15 26 RB4IN 5k
TA1OUT 16 25 RB5IN
TA3OUT 18 23 TB2OUT
5k 5k
TA4OUT 19 22 TB3OUT
32 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
TOP VIEW +5V
1µF
1µF
20
21
C1+ VCC 22
TA4OUT
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
TA4OUT
1µF V+
23 C1-
RA3IN
RA4IN
RB4IN
+5V TO +10V VOLTAGE DOUBLER 26
24 V-
C2+ 1µF
6 5 4 3 2 1 44 43 42 41 40 1µF 25 C2- +10V TO -10V VOLTAGE INVERTER
18 ENTA ENTB 27
+5V +5V
1 TA1OUT TB1OUT 44
RA2IN 7 39 RB3IN 400k
RA1IN 8 38 RB2IN 14 TA1IN TB1IN 31
ENRA 9 37 RB1IN +5V +5V
RA1OUT 10 36 ENRB 2 TA2OUT TB2OUT 43
RA2OUT 11 35 RB1OUT 400k
RA3OUT 12
MAX248 34 RB2OUT 15 TA2IN TB2IN 30
RA4OUT 13 33 RB3OUT +5V +5V
3 TA3OUT TB3OUT 42
TA1IN 14 32 RB4OUT
TA2IN 15 31 TB1IN 400k
16 TA3IN TB3IN 29
TA3IN 16 30 TB2IN
TA4IN 17 29 TB3IN
+5V +5V
4 TA4OUT TB4OUT 41
400k
18 19 20 21 22 23 24 25 26 27 28
17 TA4IN TB4IN 28
ENTA
GND
C1+
V+
C1-
C2+
C2-
V-
ENTB
TB4IN
VCC
8 RA1IN RB1IN 37
PLCC
5k 5k
5k 5k
13 RA4OUT RB4OUT 32
9 ENRA ENRB 36
GND
19
______________________________________________________________________________________ 33
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX220–MAX249
+5V
TOP VIEW 1µF
1µF
20
21
C1+ VCC 22
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
1µF V+
23 C1-
RA3IN
RA4IN
RA5IN
RB5IN
RB4IN
+5V TO +10V VOLTAGE DOUBLER 26
24 V-
C2+ 1µF
6 5 4 3 2 1 44 43 42 41 40 1µF 25 C2- +10V TO -10V VOLTAGE INVERTER
18 ENTA ENTB 27
+5V +5V
1 TA1OUT TB1OUT 44
RA2IN 7 39 RB3IN 400k
RA1IN 8 38 RB2IN 15 TA1IN TB1IN 30
ENRA 9 37 RB1IN +5V +5V
RA1OUT 10 36 ENRB 2 TA2OUT TB2OUT 43
RA2OUT 11 35 RB1OUT 400k
RA3OUT 12
MAX249 34 RB2OUT 16 TA2IN TB2IN 29
RA4OUT 13 33 RB3OUT +5V +5V
3 TA3OUT TB3OUT 42
RA5OUT 14 32 RB4OUT
TA1IN 15 31 RB5OUT 400k
17 TA3IN TB3IN 28
TA2IN 16 30 TB1IN
8 RA1IN RB1IN 37
TA3IN 17 29 TB2IN
18 19 20 21 22 23 24 25 26 27 28 5k 5k
ENTA
GND
C1+
V+
C1-
C2+
C2-
V-
ENTB
TB3IN
VCC
10 RA1OUT RB1OUT 35
7 RA2IN RB2IN 38
PLCC
5k 5k
11 RA2OUT RB2OUT 34
MAX249 FUNCTIONAL DESCRIPTION
6 RA3IN RB3IN 39
10 RECEIVERS
5 A-SIDE RECEIVERS
5k 5k
5 B-SIDE RECEIVERS
6 TRANSMITTERS 12 RA3OUT RB3OUT 33
3 A-SIDE TRANSMITTERS 5 RA4IN RB4IN 40
3 B-SIDE TRANSMITTERS
4 CONTROL PINS
5k 5k
ENABLE RECEIVER A-SIDE (ENRA)
ENABLE RECEIVER B-SIDE (ENRB) 13 RA4OUT RB4OUT 32
ENABLE RECEIVER A-SIDE (ENTA) 4 RA5IN RB5IN 41
ENABLE RECEIVER B-SIDE (ENTB)
5k 5k
14 RA5OUT RB5OUT 31
9 ENRA ENRB 36
GND
19
34 ______________________________________________________________________________________
+5V-Powered, Multichannel RS-232
Drivers/Receivers
___________________________________________Ordering Information (continued)
MAX220–MAX249
PART TEMP. RANGE PIN-PACKAGE MAX232AC/D 0°C to +70°C Dice*
MAX222CPN 0°C to +70°C 18 Plastic DIP MAX232AEPE -40°C to +85°C 16 Plastic DIP
MAX222CWN 0°C to +70°C 18 Wide SO MAX232AESE -40°C to +85°C 16 Narrow SO
MAX222C/D 0°C to +70°C Dice* MAX232AEWE -40°C to +85°C 16 Wide SO
MAX222EPN -40°C to +85°C 18 Plastic DIP MAX232AEJE -40°C to +85°C 16 CERDIP
MAX222EWN -40°C to +85°C 18 Wide SO MAX232AMJE -55°C to +125°C 16 CERDIP
MAX222EJN -40°C to +85°C 18 CERDIP MAX232AMLP -55°C to +125°C 20 LCC
MAX222MJN -55°C to +125°C 18 CERDIP MAX233CPP 0°C to +70°C 20 Plastic DIP
MAX223CAI 0°C to +70°C 28 SSOP MAX233EPP -40°C to +85°C 20 Plastic DIP
MAX223CWI 0°C to +70°C 28 Wide SO MAX233ACPP 0°C to +70°C 20 Plastic DIP
MAX223C/D 0°C to +70°C Dice* MAX233ACWP 0°C to +70°C 20 Wide SO
MAX223EAI -40°C to +85°C 28 SSOP MAX233AEPP -40°C to +85°C 20 Plastic DIP
MAX223EWI -40°C to +85°C 28 Wide SO MAX233AEWP -40°C to +85°C 20 Wide SO
MAX225CWI 0°C to +70°C 28 Wide SO MAX234CPE 0°C to +70°C 16 Plastic DIP
MAX225EWI -40°C to +85°C 28 Wide SO MAX234CWE 0°C to +70°C 16 Wide SO
MAX230CPP 0°C to +70°C 20 Plastic DIP MAX234C/D 0°C to +70°C Dice*
MAX230CWP 0°C to +70°C 20 Wide SO MAX234EPE -40°C to +85°C 16 Plastic DIP
MAX230C/D 0°C to +70°C Dice* MAX234EWE -40°C to +85°C 16 Wide SO
MAX230EPP -40°C to +85°C 20 Plastic DIP MAX234EJE -40°C to +85°C 16 CERDIP
MAX230EWP -40°C to +85°C 20 Wide SO MAX234MJE -55°C to +125°C 16 CERDIP
MAX230EJP -40°C to +85°C 20 CERDIP MAX235CPG 0°C to +70°C 24 Wide Plastic DIP
MAX230MJP -55°C to +125°C 20 CERDIP MAX235EPG -40°C to +85°C 24 Wide Plastic DIP
MAX231CPD 0°C to +70°C 14 Plastic DIP MAX235EDG -40°C to +85°C 24 Ceramic SB
MAX231CWE 0°C to +70°C 16 Wide SO MAX235MDG -55°C to +125°C 24 Ceramic SB
MAX231CJD 0°C to +70°C 14 CERDIP MAX236CNG 0°C to +70°C 24 Narrow Plastic DIP
MAX231C/D 0°C to +70°C Dice* MAX236CWG 0°C to +70°C 24 Wide SO
MAX231EPD -40°C to +85°C 14 Plastic DIP MAX236C/D 0°C to +70°C Dice*
MAX231EWE -40°C to +85°C 16 Wide SO MAX236ENG -40°C to +85°C 24 Narrow Plastic DIP
MAX231EJD -40°C to +85°C 14 CERDIP MAX236EWG -40°C to +85°C 24 Wide SO
MAX231MJD -55°C to +125°C 14 CERDIP MAX236ERG -40°C to +85°C 24 Narrow CERDIP
MAX232CPE 0°C to +70°C 16 Plastic DIP MAX236MRG -55°C to +125°C 24 Narrow CERDIP
MAX232CSE 0°C to +70°C 16 Narrow SO MAX237CNG 0°C to +70°C 24 Narrow Plastic DIP
MAX232CWE 0°C to +70°C 16 Wide SO MAX237CWG 0°C to +70°C 24 Wide SO
MAX232C/D 0°C to +70°C Dice* MAX237C/D 0°C to +70°C Dice*
MAX232EPE -40°C to +85°C 16 Plastic DIP MAX237ENG -40°C to +85°C 24 Narrow Plastic DIP
MAX232ESE -40°C to +85°C 16 Narrow SO MAX237EWG -40°C to +85°C 24 Wide SO
MAX232EWE -40°C to +85°C 16 Wide SO MAX237ERG -40°C to +85°C 24 Narrow CERDIP
MAX232EJE -40°C to +85°C 16 CERDIP MAX237MRG -55°C to +125°C 24 Narrow CERDIP
MAX232MJE -55°C to +125°C 16 CERDIP MAX238CNG 0°C to +70°C 24 Narrow Plastic DIP
MAX232MLP -55°C to +125°C 20 LCC MAX238CWG 0°C to +70°C 24 Wide SO
MAX232ACPE 0°C to +70°C 16 Plastic DIP MAX238C/D 0°C to +70°C Dice*
MAX232ACSE 0°C to +70°C 16 Narrow SO MAX238ENG -40°C to +85°C 24 Narrow Plastic DIP
MAX232ACWE 0°C to +70°C 16 Wide SO * Contact factory for dice specifications.
______________________________________________________________________________________ 35
+5V-Powered, Multichannel RS-232
Drivers/Receivers
___________________________________________Ordering Information (continued)
MAX220–MAX249
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
36 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1997 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.