Dgca Module 07 Part 04

WWW.DGCAQUESTIONPAPERS.
IN - DGCA CAR -66 MODULE 7 PART -4
Visit to download all latest EASA / DGCA CAR 66 Module examination Question papers and study material
Correct Answer is. 1 in 600.

Explanation. CAAIP S Leaflet 2-10.
1(www.dgcaquestionpapers.in), Like us on Facebook @ fb/DGCAQuestionPapers ( All CAR 66 Module Exam QP Available
06. Fits and Clearances. Question Number. 5. Which of the

following shafts would you use to obtain a
clearance fit in a bush 0.750 inch diameter?.
Question Number. 1. Tolerances are
classified in two ways, these are. Option A. 0.752 inch.
Option A. Dimensional and isometric. Option B. 0.748 inch.
Option B. Upper and lower. Option C. 750 inch.
Option C. Dimensional and geometric. Correct Answer is. 0.748 inch.
Correct Answer is. Dimensional and Explanation. NIL.
geometric.
Explanation. CAAIP S leaflet 2-1 p16 para 5.11.
Question Number. 6. Which of the
following is checked when using a 'GO / NO -GO'
gauge?.
Question Number. 2. The maximum Option A. Clearance.
permissible bow in a steel tube is. Option B. Tolerance.
Option A. 1 : 400. Option C. Allowance.
Option B. 1 : 200. Correct Answer is. Tolerance.
Option C. 1 : 600. Explanation. NIL.
Correct Answer is. 1 : 600.
Explanation. CAAIP S Leaflet 6-4.
Question Number. 7. Which of the
following is a 'Bilateral Tolerance'?.
Question Number. 3. The equipment Option A. 2 inches -0.002.
required to carry out a run-out check on a shaft Option B. 2 inches +0.002.
would be. Option C. 2 inches ±0.002.
Option A. a DTI and 'V' blocks. Correct Answer is. 2 inches ±0.002.
Option B. a ball bearing and a micrometer. Explanation. NIL.
Option C. a surface plate and a three leg

trammel. Question Number. 8. A tolerance is.
Correct Answer is. a DTI and 'V' blocks.
Explanation. AC43.13-1B Page 4-20. Option A. a permitted difference between
new and worn dimensions.
Option B. a permitted variation on a
Question Number. 4. What is the dimension to allow for inaccuracy of equipment.
maximum bow allowed in a strut?.
Option A. 1 in 200. Option C. a required difference in dimension
Option B. 1 in 500. between mating parts to obtain a certain class of
Page
Option C. 1 in 600. fit.
DOWNLOAD OUR MOBILE APP FROM PLAY STORE @DGCA QUESTION PAPERS
IF YOU HAVE PREVIOUS SESSION QUESTION PAPERS, SHARE WITH US AT [email protected]
WWW.DGCAQUESTIONPAPERS.IN - DGCA CAR -66 MODULE 7 PART -4
Correct Answer is. a permitted variation on a Option A. no less than ten times the depth.
dimension to allow for inaccuracy of equipment.
Option B. no less than twenty times the

Explanation. NIL. depth.
Option C. no more than twenty times the
depth.
Question Number. 9. A transition fit is Correct Answer is. no less than twenty times
one in which the shaft is. the depth.
Option A. larger than the hole. Explanation. AC43 6.118 6-23.
Option B. smaller than the hole.
Option C. the same size as the hole.
Correct Answer is. the same size as the hole. Question Number. 13. A press fit
requires.
Explanation. BS 4500 Datasheet 4500A., Option A. some sort of driving force.
External document. Option B. the shaft to be shrunk by cooling.
www.tech.plym.ac.uk/sme/disnotes/tola.p
df Option C. the hole to be expanded by heat.
Correct Answer is. some sort of driving force.

Question Number. 10. The length of a
blended repair of corrosion should be no less than. Explanation. A press fit is a small interference
only.
Option A. 10 times its depth.
Option B. 20 times its depth.
Option C. 5 times its depth. Question Number. 14. What is the typical
Correct Answer is. 20 times its depth. acceptable limit of a dent on a frame member?.
Explanation. NIL.
Option A. One and a half times the skin
thickness.
Question Number. 11. If there is a Option B. Twice the skin gauge and 0.75 inch
positive allowance between the smallest possible diameter.
hole and the largest possible shaft, the fit is known Option C. One gauge depth and 0.75 inch
as. diameter.
Option A. a transition fit. Correct Answer is. One gauge depth and 0.75
Option B. a clearance fit. inch diameter.
Option C. an interference fit. Explanation. NIL.
Correct Answer is. a clearance fit.
Explanation. NIL.
Question Number. 15. A light drive
clearance between 3/4 inch diameter bolt and
Question Number. 12. After mechanical hole, on a drawing would be shown as.
removal of corrosion on an aluminium alloy Option A. 0.005 Inches.
casting, the length of the blended recess should Option B. 0.0015 Inches.
Page
be. Option C. 0.0025 Inches.
Correct Answer is. 0.0015 Inches. Explanation. CAAIP S Leaflet 11-5 Para.8.8.
Explanation. AC43 says 0.0006 for a 3/8 in. bolt,
so 0.0015 is the closest (and reasonable for a 3/4

in. bolt).
Question Number. 4. With a rear release
07. Electrical Cables and Connectors. connector, the pin will be.
Option A. released from the front and
extracted from the rear.
Question Number. 1. In a front release Option B. released from the rear and
connector the pin will be. extracted from the front.
Option A. released from rear and extracted Option C. released from the rear and
from the front. extracted from the rear.
Option B. released from the front and Correct Answer is. released from the rear and
extracted from the front. extracted from the rear.
Option C. released from the front and Explanation. CAAIP S Leaflet 9-3, 8.3.2 (b) (i).
extracted from the rear.
Correct Answer is. released from the front
and extracted from the rear.
Explanation. CAAIP S Leaflet 9-3 8.3.2. Question Number. 5. The maximum
operating temperature for a nickel plated copper
or aluminium connector is.
Option A. 260°C.
Question Number. 2. A wire clamped Option B. 135°C.
vertically at one end and horizontally at the other Option C. 200°C.
end should have a bend radius of no less than. Correct Answer is. 260°C.
Explanation. CAAIP S leaflet 11-5 para 7.2.1.
Option A. 3 times the diameter of the wire.
Option B. 5 times the diameter of the wire.

Question Number. 6. What gauge of pin
Option C. 10 times the diameter of the wire. would a yellow plastic insert/extract tool be used
on?.
Correct Answer is. 3 times the diameter of Option A. 16 - 14.
the wire. Option B. 12 - 10.
Explanation. CAIP S AL/3-2 6.4. Option C. 22 - 18.
Correct Answer is. 12 - 10.
Explanation. NIL.
Question Number. 3. Glycol deicer fluid
in contact with a silver cable can cause.
Option A. a fire. Question Number. 7. Can the insulation
Option B. disintegration of the cable grip be adjusted on a PIDG crimp tool?.
insulation. Option A. No.
Option C. corrosion. Option B. Yes by turning a knob.
Page
Correct Answer is. a fire. Option C. Yes by adjusting the pins.
Correct Answer is. Yes by adjusting the pins. Option A. 12 - 10.

Option B. 16 - 14.
Explanation. NIL. Option C. 22 - 18.

Correct Answer is. 16 - 14.
Explanation. NIL.
Question Number. 8. What gauge of pin
would a red plastic insert/extract tool be used on?.
Question Number. 12. The insulation
Option A. 12 - 10. resistance for wiring in undercarriage wheel-wells
Option B. 22 - 18. should normally be not less than.
Option C. 16 - 14. Option A. 10 megohms.
Correct Answer is. 22 - 18. Option B. 5 megohms.
Explanation. Boeing Standard Wiring Practices, Option C. 2 megohms.
External website. Correct Answer is. 2 megohms.
http://www.cheifaircraft.com/Aircraft/Inst Explanation. CAIP S EEL/1-6 Para 4-5-4 (a).
allationSupply/Terminals.html
Question Number. 9. What cable would Question Number. 13. What causes
you use where temperatures are going to exceed knuckling on older type electrical cables?.
200°C?.
Option A. Tinned copper or aluminium. Option A. Over-temperature soldering.
Option B. Silver plated copper or aluminium. Option B. Applying cable ties too tightly.
Option C. Excessive pull through forces.
Option C. Nickel plated copper or aluminium. Correct Answer is. Excessive pull through
forces.
Correct Answer is. Nickel plated copper or Explanation. Leaflet 1l-5 8.6.
aluminium.
Explanation. CAAIP S Leaflet 11-5, 7.2.1.
Question Number. 14. To find a high
resistance or open circuit, carry out.
Option A. a milli-volt drop test.
Question Number. 10. How long should a Option B. a continuity check.
fireproof cable last in a fire?. Option C. a bonding check.
Option A. 5 minutes. Correct Answer is. a continuity check.
Option B. 50 minutes. Explanation. CAAIP S Leaflet 9-1, 4.2.1.
Option C. 15 minutes.
Correct Answer is. 15 minutes.
Explanation. NIL.
Question Number. 15. The maximum
bonding resistance on an aircraft primary structure
Question Number. 11. What gauge of pin should be.
would a blue plastic insert / extract tool be used Option A. 0.01 ohms.
Page
on?. Option B. 0.001 ohms.
Option C. 0.05 ohms. Explanation. CAAIP S Leaflet 9-3 fig 2.

Correct Answer is. 0.05 ohms.
Explanation. CAAIP S Leaflet 9-1, 3.8.
Question Number. 19. When referring to

Question Number. 16. Before effecting a fuses, HRC means.
crimp, the bare ends of a cable should be. Option A. high rupture capacity.
Option B. hot running capacity.
Option A. tightly twisted. Option C. high running current.
Option B. twisted lightly in the direction of Correct Answer is. high rupture capacity.
the lay. Explanation. High Rupturing Capacity.
Option C. straightened out.
Correct Answer is. twisted lightly in the
direction of the lay.
Explanation. CAAIP S Leaflet 9-3, 7.5.3. Question Number. 20. When wiring an
electrical component to a plug, the live wire is
coloured.
Option A. blue.
Question Number. 17. The number of the Option B. green and yellow.
dots impressed on the insulation of the pre- Option C. brown.
insulated connectors during crimping indicates Correct Answer is. brown.
that. Explanation. NIL.
Option A. the correct connector has been
used.
Option B. the correct tool was used to effect Question Number. 21. A hole is placed in
the connection. the lowest point of electrical cable conduit.
Option C. the crimp is properly formed.
Correct Answer is. the correct tool was used Option A. to allow for pull-through of the
to effect the connection. cables.
Explanation. NIL. Option B. to secure the conduit to a piece of
aircraft structure.
Option C. to allow for drainage of moisture.
Question Number. 18. The pressure of
the insulation crimp jaws on the PIDG crimping Correct Answer is. to allow for drainage of
tool can be changed by. moisture.
Option A. varying the torque applied to the Explanation. Aircraft Electricity and Electronics.
handles. Eismin 5th Edition page 65.
Option B. using different coloured crimping
pliers and terminations.
Option C. changing the position of the pins. Question Number. 22. The minimum
distance between electrical cable splices is.
Correct Answer is. changing the position of
the pins. Option A. 3 feet.
Page
Option B. 12 inches.
Option C. 500 mm. Option A. the bypass valve opens and the
Correct Answer is. 500 mm. ram returns to neutral.
Explanation. NIL. Option B. the foot pedal force is at

maximum.
Option C. the bypass valve closes and the
Question Number. 23. A fire resistant ram returns to neutral.
cable is proof tested by exposure to a standard fire Correct Answer is. the bypass valve opens
for. and the ram returns to neutral.
Option A. 30 minutes. Explanation. NIL.
Option B. 5 minutes.
Option C. 15 minutes.
Correct Answer is. 5 minutes. Question Number. 27. The type of
Explanation. CAAIP S Leaflet 11-5 4.5 and EASA binding tape used for cables in temperatures
CS-1 Pg.6. above 260°C is which of the following?.
Option A. Nomex.
Option B. Teflon.
Question Number. 24. When fitting Option C. Nylon.
coaxial cable connectors it is important to. Correct Answer is. Teflon.
Explanation. This is probably referring to the
Option A. fit the correct lock nuts. Teflon tape referred to in Aircraft Electricity and
Option B. make sure the outer cup is fitted Electronics by Eismin 5th Edition Page 69. Also
the correct way round. AC43 Para.11.96 z and Appendix 1 (Teflon is
Option C. not damage any seals fitted. Dupont trade-name for PTFE).
Correct Answer is. not damage any seals
fitted.
Explanation. NIL. Question Number. 28. What is the
minimum bend radius of a loom adequately
supported at a terminal block?.
Question Number. 25. When inserting Option A. 10 * diameter.
pins into a front release connector the inserting Option B. 8 * diameter.
tool should be used with the gap facing which Option C. 3 * diameter.
direction?. Correct Answer is. 3 * diameter.
Option A. The centre of the connector. Explanation. Leaflet 9-3 7.3.
Option B. Either direction.
Option C. The outside of the connector.
Correct Answer is. The outside of the Question Number. 29. How are front
connector. release pins removed?.
Explanation. Leaflet 9-3 Para.8.3.2. Option A. The tool is inserted from the front
and the pin is removed from the front.
Option B. The tool is inserted from the rear
Question Number. 26. When using a and the pin Is removed from the front.
hydraulic crimping tool, after completing the Option C. The tool is inserted from the front
crimping operation, the crimp is formed when and the pin is removed from the rear.
Page
when.
Correct Answer is. The tool is inserted from Question Number. 33. When using a heat
the front and the pin is removed from the rear. shrink gun, what should the temperature of the
Explanation. Leaflet 9-3 8.3.2 (b)(ii). gun be set to?.

Option A. 100° below the heat shrink
temperature.
Question Number. 30. If a co-axial cable Option B. 15° below the heat shrink
clamp is over tightened so as to compress the temperature.
dielectric, how will the capacitance change?. Option C. 100° above the heat shrink
temperature.
Option A. Stay the same. Correct Answer is. 100° above the heat shrink
Option B. Increase. temperature.
Option C. Decrease. Explanation. A trick question. The 'Heat shrink
Correct Answer is. Increase. temperature' is the normal 'room' temperature of
Explanation. AC43 11-117. Decreasing dielectric about 20-25°C. Most heat shrink materials shrink
thickness (of a capacitor) increases its capacitance. at around 125°C.
Question Number. 34. In an electrical

Question Number. 31. What is the cable 1EF6B22NMS, what does the letter E
minimum bend radius of a single co-axial cable?. represent?.
Option A. Circuit function.
Option A. 10 * diameter. Option B. Cable size.
Option B. 8 * diameter. Option C. Segment letter.
Option C. 6 * diameter. Correct Answer is. Circuit function.
Correct Answer is. 6 * diameter. Explanation. Leaflet 9-3 Para.9.1.1.
Explanation. AC43.13-1B Page 11-45 Para.11-96
bb. No British reference found.
Question Number. 35. On a coaxial cable,
cable impedance is.
Question Number. 32. What is wet arc Option A. proportional to length.
tracking?. Option B. not effected by length.
Option A. A fault caused by hot stamp Option C. inversely proportional to length.
printing.
Option B. A fault caused by insulation Correct Answer is. not effected by length.
damage. Explanation. The length has nothing to do with
Option C. A fault caused by 'knuckling a coaxial cable impedance. External website.
through'. http://www.epanorama.net/documents/w
Correct Answer is. A fault caused by hot iring/cable_impedance.html
stamp printing.
Explanation. AC43.13-1B, 11-210 and CAAIP S
Leaflet 11-5 Para.8.2. Question Number. 36. A secondary earth
is.
Option A. not less than 0.5mm cross
Page
sectional area.
Option B. 18 AWG. Question Number. 40. When

Option C. 22 AWG. manufacturing an electrical connector the unused
Correct Answer is. 18 AWG. holes are.

Explanation. Leaflet 9-1 para.3.3 & EEL/1-6 Option A. filled with connectors.
3.3.1 (a) ii. Option B. filled with connectors and blanked.
Option C. covered with blanks.

Question Number. 37. E' on a wire, under Correct Answer is. filled with connectors and
ATA 100 is a. blanked.
Option A. phase indication. Explanation. Leaflet 9-3 para 8.3.2 f)iii) and AC
Option B. system ID code. 43.13B 11-234.
Option C. cable size.
Correct Answer is. system ID code.
Explanation. Leaflet 9-3 para.9.1.1. Question Number. 41. Co-axial cable is
preferred to airframe cable in which application?.
Question Number. 38. To prevent wet arc Option A. Where the diameter of cable is not
tracking. important.
Option A. cable grips should be tight. Option B. High frequency interference.
Option B. ensure hot stamp printing is Option C. Low frequency interference.
controlled. Correct Answer is. Where the diameter of
Option C. cables should not be stretched. cable is not important.
Correct Answer is. ensure hot stamp printing Explanation. Cable is susceptible to all
is controlled. frequencies of interference. Co-axial cable is
Explanation. Leaflet 11-5 8.2 and 6.7. reasonably well protected from all frequencies of
interference but is much thicker overall than
airframe cable.
Question Number. 39. When splicing a
cable with a soldered joint, the operation is
finished when. Question Number. 42. Forward release
Option A. the solder has melted. electrical connectors are removed by the wire
Option B. the solder sleeve disappears. being.
Option C. the solder and insulation have Option A. pushed forwards.
formed. Option B. twisted to the right.
Correct Answer is. the solder and insulation Option C. pulled backwards.
have formed. Correct Answer is. pulled backwards.
Explanation. The solder sleeve is a plastic Explanation. Leaflet 9-3 8.32 II.
cylinder with two rings of plastic at each end and a
solder ring in the middle. When heated the
cylinder first melts on to the wires, then the plastic Question Number. 43. When crimping
rings melt, sealing the ends of the cylinder. wires, the wires should be.
Option A. straight.
Option B. lightly twisted.
Page
Option C. twisted.
Correct Answer is. lightly twisted. Explanation. NIL.

Explanation. Leaflet 9-3 7.5.5 ©.
Question Number. 48. The value of the

Question Number. 44. Why are copper insulation resistance of an electric motor
wires used in electrical systems?. compared to its supply leads is.
Option A. They have high permeability. Option A. greater.
Option B. They do not give off a magnetic Option B. same.
field. Option C. smaller.
Option C. They have a low resistance to Correct Answer is. smaller.
current. Explanation. Leaflet 9-1 4.5.4 (c) 'Rated voltage
Correct Answer is. They have a low resistance / 150' whereas supply leads must take the supply
to current. voltage at least.
Explanation. Copper has a low resistance to
current.
Question Number. 49. According to ATA
100, a symbol code 'X' on a wiring number
Question Number. 45. When crimping denotes.
wires, the wire should. Option A. a warning circuit.
Option A. be flush with the crimp. Option B. a ground circuit.
Option B. extend 0.8 mm beyond the crimp. Option C. AC power.
Correct Answer is. AC power.
Option C. be beneath the crimp. Explanation. Aircraft Electricity and Electronics.
Correct Answer is. extend 0.8 mm beyond the Eismin 5th Edition page 79.
crimp.
Explanation. NIL.
Question Number. 50. When securing
wire after it leaves an LRU, cable bundle bends
Question Number. 46. 1EF6B22 NMSV. should be not less than?.
What does the B mean?. Option A. minimum radius of five times the
Option A. Segment letter. outside diameter of the cable, or cable bundle.
Option B. Cable number. Option B. minimum radius of three times the
Option C. Circuit function. outside diameter of the cable, or cable bundle.
Correct Answer is. Segment letter. Option C. minimum radius of eight times the
Explanation. Leaflet 9-3 9.1.1. outside diameter of the cable, or cable bundle.
Correct Answer is. minimum radius of eight
times the outside diameter of the cable, or cable
Question Number. 47. A white/blue bundle.
insertion-extraction tool would be used on a cable Explanation. CAAIP 9-3, 7.4 states 8 times the
of what size?. diameter (not 3 times, because it is not at a
Option A. 10. terminal block).
Option B. 22.
Option C. 16.
Page
Correct Answer is. 16.
Question Number. 51. When terminating Explanation. Leaflet 9-3 7.5.5 (d).
an aluminium cable, what preparations would be
carried out before crimping?.

Option A. Degrease stripped cable. Question Number. 55. A cable loom
Option B. Just terminate. should be protected by conduit when fed through
Option C. Apply a mixture of 50% petroleum the.
jelly and zinc oxide. Option A. main equipment centre.
Correct Answer is. Apply a mixture of 50% Option B. wheelwell door.
petroleum jelly and zinc oxide. Option C. cargo compartment ceiling.
Explanation. CAAIP S Leaflet 9-1 3.5.4. Correct Answer is. wheelwell door.
Explanation. NIL.
Question Number. 52. An in-line splice Question Number. 56. The size of proper
should be positioned on the. conduit for electrical wires must be.
Option A. terminal of the loom. Option A. 75% larger than the maximum
Option B. outside of the loom. diameter of wires.
Option C. outer surface of the loom for easy Option B. 25% larger than the maximum
inspection. diameter of wires.
Correct Answer is. outer surface of the loom Option C. 100% larger than the average
for easy inspection. diameter of wires.
Explanation. NIL. Correct Answer is. 25% larger than the
maximum diameter of wires.
Explanation. AC43 11-249.
Question Number. 53. A conductor after
being crimped. The maximum amount of
conductor which protrudes from the terminal end Question Number. 57. Blue metal extract
should be tool would be used with contacts sized.
Option A. 1/32 inch. Option A. 16.
Option B. 1/8 inch. Option B. 12.
Option C. 1/16 inch. Option C. 22.
Correct Answer is. 1/32 inch. Correct Answer is. 16.
Explanation. Leaflet 9-1 Fig 1 (0.8 mm = 1/32 Explanation. NIL.
in.).
Question Number. 58. A Silver coated

Question Number. 54. Two or more conductor in an unpresurised area is subject to
operations should be performed to strip wire with moisture and has a damaged coating would be
hand operated wire stripper if the total stripping likely to cause.
length exceeds. Option A. Wet Arc Tracking.
Option A. 0.50 in. Option B. Knuckling Through.
Option B. 0.75 inch. Option C. Red Plague.
Option C. 0.25 in. Correct Answer is. Red Plague.
Page
Correct Answer is. 0.75 inch. Explanation. NIL.
Question Number. 5. What is the

08. Riveting. normal spacing between rivets?.
Option A. 2 D.
Option B. 4 D.
Question Number. 1. When riveting, the Option C. 3 D.
distance from the edge to the rivet (land) should Correct Answer is. 4 D.
not be less than. Explanation. NIL.
Option A. 1D.
Option B. 2D.
Option C. 4D. Question Number. 6. In British rivets
Correct Answer is. 2D. (solid) what is the length grading unit?.
Explanation. A&P Technician Airframe Textbook Option A. 1/16.
2-53. Option B. 1/10.
Option C. 1/32.
Correct Answer is. 1/16.
Question Number. 2. The strength of a Explanation. CAIP S BL/6-1, 4.2.
riveted joint compared to that of the original metal
is.
Option A. 75%. Question Number. 7. If the thickness of
Option B. 100%. a single sheet of material, about to be joined by
Option C. 125%. riveting was 1/16 of an inch thick what would be
Correct Answer is. 75%. the approximate diameter of the rivets to be
Explanation. NIL. used?.
Option A. 1/16 inch.
Option B. 3/16 inch.
Question Number. 3. A repair has a Option C. 1/8 inch.
double riveted joint. The shear strength would be. Correct Answer is. 3/16 inch.
Explanation. CAIP S BL/6-29 Para 3.
Option A. 125%.
Option B. 75%.
Option C. 100%. Question Number. 8. Regarding riveting,
Correct Answer is. 75%. which of the following is correct?.
Explanation. NIL. Option A. Both of the above are correct.
Option B. The length of a countersunk rivet
(flush head) is measured from the end of the rivet
Question Number. 4. The standard to the top of the countersunk head.
minimum rivet row spacing is. Option C. The length of a round head or flat
Option A. 2 1/4 D. head is measured from the end of the rivet to
Option B. 3 D. underside of rivet head.
Option C. 4 D. Correct Answer is. Both of the above are
Correct Answer is. 4 D. correct.
Explanation. NIL. Explanation. Jeppesen A&P Airframe Textbook
2-36 and AC43 page 4.16.
Page
Question Number. 9. When riveting, a Question Number. 12. Rivets kept at a

certain clearance must exist between the rivet and temperature of between –15°C and –20°C are
the hole in which it is fitted, to allow for shank usable for.
expansion. If the clearance is too large, what could Option A. 150 days.
be the result?. Option B. 150 minutes.
Option A. Indentations by rivet head on the Option C. 150 hours.
material. Correct Answer is. 150 hours.
Option B. Separation of the sheets may Explanation. CAIP S BL/6-27 Para 6-2.
occur.
Option C. Sheet may tend to buckle.
Correct Answer is. Separation of the sheets Question Number. 13. Avdel rivets are
may occur. closed by.
Explanation. CAIP S BL/6-29 Para 9.3.1 -Fig 4, Option A. a broaching process.
Too small a hole causes buckling, too large causes Option B. a tapered mandrel.
separation. Option C. a squeezing process.
Correct Answer is. a broaching process.
Explanation. CAIP S BL/6-28 Para 3.2 Fig 2.
Question Number. 10. To replace one 1/8
inch rivet.
Option A. three 1/16 inch rivets would be Question Number. 14. What is the
required. purpose of the Avdel pin tester?.
Option B. two 1/16 inch rivets would be Option A. To test the tightness of the pin in
required. the rivet.
Option C. four 1/16 inch rivets would be Option B. To test the tightness of the rivet in
required. the hole.
Correct Answer is. four 1/16 inch rivets would Option C. To test the shear strength of the
be required. pin.
Explanation. CAIP BL/6-27 in the NOTE below Correct Answer is. To test the tightness of the
para 5.3. pin in the rivet.
Explanation. Inspection after Installation of
AVDEL rivets. The security of the mandrel must be
Question Number. 11. If treated rivets tested.Use the AVDEL PIN TESTER (Part Number
have not been used within the prescribed time 79/95-0700) set to 35 Lbs. No movement of the
they can be re-treated. What is the maximum mandrel is permitted. Ref. SRM A300-600.Chapter
number of times that they can be heat-treated?. 51-40-21.
Option A. If no more in Stores, as many

times as required. Question Number. 15. The stems of an
Option B. Twice only. Avdel rivet are.
Option C. Three times. Option A. removed with the riveting tool.
Correct Answer is. Three times. Option B. nipped off and milled flush with
Explanation. CAIP S BL/6-27 Para 6-3. the head.
Page
Option C. removed with a taper punch.
Correct Answer is. nipped off and milled flush

with the head.
Explanation. NIL.
Question Number. 16. What is the

pressure range for the Avdel Riveter Type F?.
Option A. 40 to 60 lbs per sq. in. Question Number. 19. Rivet allowance is.
Option B. 20 to 60 lbs per sq. in.
Option C. 60 to 80 lbs per sq. in. Option A. the distance the rivet is positioned
Correct Answer is. 60 to 80 lbs per sq. in. from the edge of the repair plate.
Explanation. NIL. Option B. the amount of material required to
form the rivet on installation.
Option C. the distance between rivets in the
Question Number. 17. When same row.
countersinking rivet holes in a material. Correct Answer is. the amount of material
Option A. a special countersinking bit with a required to form the rivet on installation.
pad to prevent drilling too deep should be used. Explanation. BL/6-29 8.1.
Option B. a plain countersinking bit should
be used.
Option C. the rivet head should stand 1/32 Question Number. 20. What is the
of an inch above the surface. approximate distance of the sphere of influence of
Correct Answer is. a special countersinking a rivet?.
bit with a pad to prevent drilling too deep should Option A. 4 D.
be used. Option B. 2 D.
Explanation. NIL. Option C. 5 D.
Correct Answer is. 5 D.
Explanation. NIL.
Question Number. 18. The riveting defect
in the figure shown is.
Question Number. 21. Rivet clearance is.
Option A. the distance between rivets in the

same row.
Option A. too much hammering. Option B. the amount that the rivet hole
Option B. the dolly was not square. diameter exceeds the rivet diameter.
Option C. the snap was not square. Option C. the distance between rows of
Correct Answer is. the snap was not square. rivets.
Correct Answer is. the amount that the rivet
Explanation. BL/6-29 Para 9-3-1 Fig 4. hole diameter exceeds the rivet diameter.
Explanation. BL/6-29 4.2.
Page
Question Number. 22. The minimum rivet Correct Answer is. the thickness of plates
pitch is. which can be fastened.
Option A. 2 1/2 * the rivet diameter. Explanation. NIL.

Option B. 3 * the rivet diameter.
Option C. 2 * the rivet diameter.
Correct Answer is. 3 * the rivet diameter. Question Number. 25. The strength of a
Explanation. A&P Airframe Textbook CH12-37 riveted joint is determined by.
Fig 12-57. (BL/6-29 3.1 - staggered double row Option A. shear strength and pitch of rivet.
only).
Option B. pitch and tensile strength of rivet.
Question Number. 23. The riveting defect Option C. shear strength of rivet and
in the figure shown is. material it is made of.
Correct Answer is. shear strength and pitch of
rivet.
Explanation. BL/6-27 5.2 The shear strength of
the rivet is determined by the material it is made
Option A. the snap was not square. of. All rivets are under shear.
Option B. the hole was too small.
Option C. an incorrect snap has been used.
Question Number. 26. If the bearing
Correct Answer is. the hole was too small. strength of a metal is greater than the shear
Explanation. CAIP S BL/6-29 Para 9.3.1 Fig 4. strength of the rivet, what will occur?.
AC43 21. Option A. Rivet will joggle.
Option B. Rivet will show incorrectly
installed.
Option C. Rivet will pull through the metal.
Correct Answer is. Rivet will joggle.

Explanation. NIL.
Question Number. 24. The ‘grip’ of a rivet

is.
Option A. the length of rivet left to form the
head.
Option B. the thickness of plates which can
be fastened.
Option C. the area of the plates held firmly
together.
Page

Dgca Module 07 Part 04

Uploaded by

Copyright:

Available Formats

Dgca Module 07 Part 04

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dgca Module 07 Part 04

Uploaded by

Copyright:

Available Formats

WWW.DGCAQUESTIONPAPERS.

IN - DGCA CAR -66 MODULE 7 PART -4

Correct Answer is. 1 in 600.

06. Fits and Clearances. Question Number. 5. Which of the

Option C. a surface plate and a three leg

Option C. 1 in 600. fit.

Option B. no less than twenty times the

Correct Answer is. some sort of driving force.

be. Option C. 0.0025 Inches.

so 0.0015 is the closest (and reasonable for a 3/4

Option B. 5 times the diameter of the wire.

Correct Answer is. a fire. Option C. Yes by adjusting the pins.

Correct Answer is. Yes by adjusting the pins. Option A. 12 - 10.

Explanation. NIL. Option C. 22 - 18.

on?. Option B. 0.001 ohms.

Option C. 0.05 ohms. Explanation. CAAIP S Leaflet 9-3 fig 2.

Explanation. CAAIP S Leaflet 9-1, 3.8.

Question Number. 19. When referring to

Explanation. NIL. Option B. the foot pedal force is at

Explanation. Leaflet 9-3 8.3.2 (b)(ii). gun be set to?.

Question Number. 34. In an electrical

Option B. 18 AWG. Question Number. 40. When

Correct Answer is. 18 AWG. holes are.

Option C. covered with blanks.

Correct Answer is. lightly twisted. Explanation. NIL.

Question Number. 48. The value of the

Correct Answer is. 16.

carried out before crimping?.

Question Number. 58. A Silver coated

Correct Answer is. 0.75 inch. Explanation. NIL.

Question Number. 5. What is the

Question Number. 9. When riveting, a Question Number. 12. Rivets kept at a

Option A. If no more in Stores, as many

Option C. removed with a taper punch.

Correct Answer is. nipped off and milled flush

Question Number. 16. What is the

Option A. the distance between rivets in the

Option A. 2 1/2 * the rivet diameter. Explanation. NIL.

Correct Answer is. Rivet will joggle.

Question Number. 24. The ‘grip’ of a rivet

You might also like