Scribd Logo
Upload

Welcome to Scribd!

  • 94 views

    Lifting lug-U-FA 121 - R0

    Uploaded by

    manish318
    The document provides design specifications and stress analysis results for a lifting lug attached to a vessel. It specifies dimensions and materials for the vessel and lifting lug. Stress analyses were performed for weld shear stress, shear stress in the lug above the hole, pin hole bearing stress, and combined stress at the base of the lug. All calculated stresses were found to be below the allowable stresses for the materials.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Lifting lug-U-FA 121 - R0

    Uploaded by

    manish318
    94 views2 pages
    The document provides design specifications and stress analysis results for a lifting lug attached to a vessel. It specifies dimensions and materials for the vessel and lifting lug. Stress analyses were performed for weld shear stress, shear stress in the lug above the hole, pin hole bearing stress, and combined stress at the base of the lug. All calculated stresses were found to be below the allowable stresses for the materials.

    Original Description:

    Lifting lug for pressure vessel

    Original Title

    lifting lug-U-FA 121_R0

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides design specifications and stress analysis results for a lifting lug attached to a vessel. It specifies dimensions and materials for the vessel and lifting lug. Stress analyses were performed for weld shear stress, shear stress in the lug above the hole, pin hole bearing stress, and combined stress at the base of the lug. All calculated stresses were found to be below the allowable stresses for the materials.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    94 views2 pages

    Lifting lug-U-FA 121 - R0

    Uploaded by

    manish318
    The document provides design specifications and stress analysis results for a lifting lug attached to a vessel. It specifies dimensions and materials for the vessel and lifting lug. Stress analyses were performed for weld shear stress, shear stress in the lug above the hole, pin hole bearing stress, and combined stress at the base of the lug. All calculated stresses were found to be below the allowable stresses for the materials.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Input Echo, Leg & Lug Item 1, Description: New Leg/Lug

    Design Internal Pressure 0.00 MPa


    Design Temperature for Attachment TEMP 40.00 C
    Vessel Outside Diameter OD 1210.000 mm
    Vessel Wall Thickness Ts 5.0000 mm
    Vessel Corrosion Allowance Cas 0.0000 mm
    Vessel Material SA-240 304L
    Vessel Material UNS Number S30403
    Vessel Allowable Stress at Design S 115.23 MPa
    Analysis Type: Lifting Lug

    Empty Weight of Vessel Wemp 10000.00 N


    Operating Weight of Vessel (vertical load ) W 0.00 N

    Lifting Lug Material SA-240 304


    Lifting Lug Material UNS Number S30400
    Lifting Lug Yield Stress YIELD 205.18 MPa

    Lifting Lug Orientation to Vessel Perpendicular


    Total Height of Lifting Lug w 160.0000 mm
    Thickness of Lifting Lug t 12.0000 mm
    Diameter of Hole in Lifting Lug dh 60.0000 mm
    Radius of Semi-Circular Arc of Lifting Lug r 60.0000 mm
    Height of Lug from bottom to Center of Hole h 100.0000 mm
    Offset from Vessel OD to Center of Hole off 100.0000 mm
    Minimum thickness of Fillet Weld around Lug tw 5.0000 mm
    Length of weld along side of Lifting Lug wl 12.0000 mm
    Length of Weld along Bottom of Lifting Lug wb 160.0000 mm
    Lift Orientation Vertical
    Force Along Vessel Axis Fax 5000.00 N
    Force Normal to Vessel Fn 0.00 N
    Force Tangential to Vessel Ft 0.00 N
    Impact Factor Impfac 1.50

    Occasional Load Factor (AISC A5.2) Occfac 1.00

    Results for lifting lugs, Description : New Leg/Lug

    Weld Group Inertia about the Circumferential Axis ILC 120373.227 mm^4
    Weld Group Centroid distance in the Long. Direction YLL 11.000 mm
    Dist. of Weld Group Centroid from Lug bottom YLL_B 6.000 mm
    Weld Group Inertia about the Longitudinal Axis ILL 3422249.750 mm^4
    Weld Group Centroid Distance in the Circ. Direction YLC 11.000 mm

    Applying the Impact factor to the loads:


    Fax = 5000.00 * 1.50 = 7500.00 N

    Primary Shear Stress in the Welds due to Shear Loads [Ssll]:


    = Sqrt( Fax^2+Ft^2+Fn^2 ) / ( (2*wl+wb) * tw )
    = Sqrt(7500^2+0^2+0^2) / ( (2*12.0 +160.0 ) * 5.0000 )
    = 8.16 MPa

    Shear Stress in the Welds due to Bending Loads [Sblf]:


    = (Fn*(h-YLL_B)) *YLL/ILC + (Fax*off *YLL/ILC) + (Ft*off *YLC/ILL)
    = (0 *(100.000 -6.000 )) * 11.000 /120373.227 +
    (7500 *100.000 * 11.000 /120373.227) +
    (0 *100.000 * 11.000 /3422249 )
    = 68.59 MPa

    Total Shear Stress for Combined Loads [St]:


    = Ssll + Sblf
    = 8.159 + 68.592
    = 76.75 MPa

    Allowable Shear Stress for Combined Loads [Sta]:


    = 0.4 * Yield * Occfac (AISC Shear All.)
    = 0.4 * 205 * 1.00
    = 82.07 MPa

    Shear Stress in Lug above Hole [Shs]:


    = Sqrt( Fax^2 + Fn^2 + Ft^2 ) / Sha
    = Sqrt( 7500^2 + 0^2 + 0^2 ) / 720.000
    = 10.43 MPa

    Allowable Shear Stress in Lug above Hole [Sas]:


    = 0.4 * Yield * Occfac
    = 0.4 * 205 * 1.00
    = 82.07 MPa

    Pin Hole Bearing Stress [Pbs]:


    = Sqrt( Fax^2 + Fn^2 ) / ( t * dh )
    = Sqrt( 7500^2 + 0^2 ) / ( 12.000 * 60.000 )
    = 10.43 MPa

    Allowable Bearing Stress [Pba]:


    = Min( 0.75 * Yield * Occfac, 0.9*Yield ) AISC Bearing All.
    = Min( 0.75 * 205 * 1.00 , 184.7 )
    = 153.89 MPa

    Bending stress at the base of the lug [Fbs]:


    = Ft*off / (w*t^(2) / 6) + Fax*off / (w^(2)*t / 6)
    = 0 * 100.000 / (160.000 * 12.000^(2) / 6) +
    7500 * 100.000 / (160.000^(2) * 12.000 / 6)
    = 14.66 MPa

    Tensile stress at the base of the lug [Fa]:


    = Fn / (w * t) = 0 / (160.000 * 12.000 )
    = 0.00 MPa

    Total Combined Stress at the base of the lug:


    = Fbs + Fa = 14.7 MPa

    Lug Allowable Stress for Bending and Tension:


    = Min( 0.66 * Yield * Occfac, 0.75*Yield )
    = Min( 0.66 * 205 * 1.00 , 153.9 ) = 135.4 MPa

    Note: Check the Shell Stresses using method such as WRC-107.

    Summary of Results

    Stress (MPa
    ------------------------------------------------------------------------------
    Primary Shear Stress of Weld : 76.75 82.07 Ok |
    Shear Stress above Hole : 10.43 82.07 Ok |
    Pin Hole Bearing Stress : 10.43 153.89 Ok |
    Total Combined Stress at the lug base : 14.66 135.42 Ok |

    PV Elite is a trademark of Intergraph CADWorx & Analysis Solutions, Inc. 2016

    You might also like