PCS 9799 PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 112

PCS-9799

Station Manager
Instruction Manual

NR Electric Co., Ltd.


Preface

Preface

Introduction
This guide and the relevant operating or service manual documentation for the equipment provide
full information on safe handling, commissioning and testing of this equipment.

Documentation for equipment ordered from NR is dispatched separately from manufactured


goods and may not be received at the same time. Therefore, this guide is provided to ensure that
printed information normally present on equipment is fully understood by the recipient.

Before carrying out any work on the equipment, the user should be familiar with the contents of
this manual, and read relevant chapter carefully.

This chapter describes the safety precautions recommended when using the equipment. Before
installing and using the equipment, this chapter must be thoroughly read and understood.

Health and Safety


The information in this chapter of the equipment documentation is intended to ensure that
equipment is properly installed and handled in order to maintain it in a safe condition.

When electrical equipment is in operation, dangerous voltages will be present in certain parts of
the equipment. Failure to observe warning notices, incorrect use, or improper use may endanger
personnel and equipment and cause personal injury or physical damage.

Before working in the terminal strip area, the equipment must be isolated.

Proper and safe operation of the equipment depends on appropriate shipping and handling,
proper storage, installation and commissioning, and on careful operation, maintenance and
servicing. For this reason, only qualified personnel may work on or operate the equipment.

Qualified personnel are individuals who:

 Are familiar with the installation, commissioning, and operation of the equipment and of the
system to which it is being connected;

 Are able to safely perform switching operations in accordance with accepted safety
engineering practices and are authorized to energize and de-energize equipment and to
isolate, ground, and label it;

 Are trained in the care and use of safety apparatus in accordance with safety engineering
practices;

 Are trained in emergency procedures (first aid).

PCS-9799 Station Manager i

Date: 2015-03-31
Preface

Instructions and Warnings


The following indicators and standard definitions are used:

DANGER!

It means that death, severe personal injury, or considerable equipment damage will occur if safety
precautions are disregarded.

WARNING!

It means that death, severe personal, or considerable equipment damage could occur if safety
precautions are disregarded.

CAUTION!

It means that light personal injury or equipment damage may occur if safety precautions are
disregarded. This particularly applies to damage to the device and to resulting damage of the
protected equipment.

WARNING!

The firmware may be upgraded to add new features or enhance/modify existing features,
please make sure that the version of this manual is compatible with the product in your
hand.

WARNING!

During operation of electrical equipment, certain parts of these devices are under high
voltage. Severe personal injury or significant equipment damage could result from
improper behavior.

Only qualified personnel should work on this equipment or in the vicinity of this equipment.
These personnel must be familiar with all warnings and service procedures described in
this manual, as well as safety regulations.

In particular, the general facility and safety regulations for work with high-voltage
equipment must be observed. Noncompliance may result in death, injury, or significant
equipment damage.

DANGER!

Never allow the current transformer (CT) secondary circuit connected to this equipment to
be opened while the primary system is live. Opening the CT circuit will produce a
dangerously high voltage.

ii PCS-9799 Station Manager

Date: 2015-03-31
Preface

WARNING!

 Exposed terminals

Do not touch the exposed terminals of this equipment while the power is on, as the
high voltage generated is dangerous

 Residual voltage

Hazardous voltage can be present in the DC circuit just after switching off the DC
power supply. It takes a few seconds for the voltage to discharge.

CAUTION!

 Earth

The earthing terminal of the equipment must be securely earthed.

 Operating environment

The equipment must only be used within the range of ambient environment detailed
in the specification and in an environment free of abnormal vibration.

 Ratings

Before applying AC voltage and current or the DC power supply to the equipment,
check that they conform to the equipment ratings.

 Printed circuit board

Do not attach and remove printed circuit boards when DC power to the equipment is
on, as this may cause the equipment to malfunction.

 External circuit

When connecting the output contacts of the equipment to an external circuit, carefully
check the supply voltage used in order to prevent the connected circuit from
overheating.

 Connection cable

Carefully handle the connection cable without applying excessive force.

PCS-9799 Station Manager iii

Date: 2015-03-31
Preface

Documentation Structure
The manual provides a functional and technical description of this device and a comprehensive
set of instructions for the device’s use and application.

All contents provided by this manual are summarized as below:

1 Introduction
Brief introduction of the application, functions and features

2 Technical Data
Lists of the technical data such as electrical specifications, mechanical specifications, ambient
temperature and humidity range, communication port parameters, type tests and accuracy limits

3 Operation Theory
Comprehensive and detailed functional description

4 Supervision
Automatic self-supervision function of device

5 Management
Management function (measurement, recording, metering, etc.) of this device

6 Hardware
Description of plug-in modules and definition of pins

7 Settings
Setting lists including system settings, communication settings and etc.

8 Human Machine Interface


Description of the HMI panel, LCD display and menu tree

9 Configurable Function
Brief introduction of configurable functions and configuration software

10 Communication
Introduction of the supported conmmunication protocols

11 Installation
Recommendation for unpacking, handling, inspection and storage with a guide to the mechanical
and electrical installation

12 Commissioning
Commissioning recommendation for comprising checks on the calibration and functionality of
device

iv PCS-9799 Station Manager

Date: 2015-03-31
Preface

13 Maintenance
General maintenance policy

14 Decommissioning and Disposal


General decommissioning and disposal policy

15 Manual Version History


List of instruction manual versions and history records of update.

Copyright © 2015 NR. All rights reserved.

We reserve all rights to this document and to the information contained herein. Improper use in particular reproduction and dissemination
to third parties is strictly forbidden except where expressly authorized.

The information in this manual is carefully checked periodically, and necessary corrections w ill be included in future editions. If
nevertheless any errors are detected, suggestions for correction or improvement are greatly appreciated.

We reserve the rights to make technical improvements without notice.

NR ELECTRIC CO., LTD. Tel: +86-25-87178888

Headquarters: 69, Suyuan Avenue, Jiangning, Nanjing 211102, China Fax: +86-25-87178999

Manufactory: 18, Xinfeng Road, Jiangning, Nanjing 211111, China Website: www.nrelect.com, www.nrec.com

P/N: ZL_PCS-9799_X_Instruction Manual_EN_Overseas General_X Version: R1.00

PCS-9799 Station Manager v

Date: 2015-03-31
Preface

vi PCS-9799 Station Manager

Date: 2015-03-31
1 Introduction

1 Introduction

Table of Contents
1 Introduction .......................................................................................1-a
1.1 Overview .......................................................................................................... 1-1
1.2 Functions ......................................................................................................... 1-2
1.3 Features ........................................................................................................... 1-3

PCS-9799 Station Manager 1-a

Date: 2015-03-31
1 Introduction

1-b PCS-9799 Station Manager

Date: 2015-03-31
1 Introduction

1.1 Overview

The PCS-9799 Station Manager is designed for the highest standards of performance, safety and
reliability to meet requirements of a complex substation automation system (SAS). As a part of the
SAS, it works as a station communication manager, which collects and maps signals of relays,
measurement units, control units and other IEDs the substation to higher-level systems such as
control centers (CC) or distributed control systems.

The PCS-9799 supports several protocols. In which, IEC 61850 client, IEC60870-5-101/104, NR
private 103 (Ethernet port), IEC60870-5-103 (serial port) and CDT form a standard protocol
package to satisfy most requirements. Data can be transmitted to and received from in analog
channel, digital channel or network to CC, distributed control system or other system.

The direct transmission mode of the PCS-9799 allows an independent operation of this device. So
as to avoid any interaction or influence with the HMI system to the substation's SCADA
(Supervisory Control And Data Acquisition) system.

Remote Control Center Other Functional Center

Electric Power
PCS-9799 Data Network
Station Manager
Engineer Operator
workstation workstation

Net A

Net B

Switch A

GPS

Switch B
Net A
LAN

Time
Net B
Synchronization

PCS-9794
Protocol
Converter

On-line
supervision Energy Third party IEDs
NR IEDs
device Meter

Other IEDs

The PCS-9799 Station Manager is applicable to:

1. Power system

Conventional substation and digital substation of various voltage levels

New-build substation SAS implementation and old substation reconstruction or upgrade

PCS-9799 Station Manager 1-1

Date: 2015-03-31
1 Introduction

2. Transport system

Subway, light-rail and electrified railway system

3. Industrial system

Industrial automation applications: mine, petrochemical industry, metallurgy, etc.

Note!

The additional protocol requirement besides the standard package can be customized,
please declare it clearly in the technical agreement and contract.

1.2 Functions

The PCS-9799 is a powerful device, which can meet various requirements of different substation.
It contains a full series of basic functions focus on substation automation, as well as a variety of
advanced functions, which enhance the information transmission and management.

1. Relay information acquisition

Through serial or Ethernet port, this device can communicate with protection relays to gather
their information such as SOE records, tripping signals, supervision alarms, etc.

2. Measurement & control IED information acquisition

Through serial or Ethernet port, this device can communicate with measurement & control
IEDs and intelligent meters to gather their information such as sampled values, binary status,
energy metering signals, etc.

3. Auxiliary IED information acquisition

In addition, this device can gather information of other auxiliary devices, which are useful or
crucial for the operation and safety of substation.

4. Remote control center communication

This device can realize the communication with multiple remote control centers with different
protocols. The mapping transmission tables to different centers can be customized
independently.

5. Synthetic signalization

The synthetic signalization is supported by this device with help of the configuration tool
PCS-COMM. Logical and mathematic operation of data such as AND OR NOT XOR and + - ×
÷ can be proceed for the transmission to remote control centers.

6. Remote command record and query

This device records all the commands and operations from the remote control source, include
control selection, control execution, regulation, setting modification selection, setting

1-2 PCS-9799 Station Manager

Date: 2015-03-31
1 Introduction

modification execution, signal reset, etc. All these records can be viewed and queried with
filter.

7. Communication status check and supervision

This device can automatically check and upload the communication status between itself and
the devices connected. If an abnormality is detected, a corresponding alarm will be sent to
the remote control center.

8. Time synchronization

This device supports several time synchronization formats, including IRIG-B, network SNTP,
time message, etc. It can also synchronize the connected IED with time message to unify the
time in one substation.

9. On-line maintenance and monitoring

This powerful function enables the engineer to monitor the running status of this device
through network, including running information print, message display of Ethernet port and
serial port, on-field configuration, database view, virtual measurement, file transmission,
remote rebooting, etc. With all these advanced functions, the substation upgrade becomes
convenient.

10. Channel redundancy switching

This mode based on 2 devices with the same communication configuration in one substation
and enables the channel redundancy switching for the communication with different remote
control centers (if one channel fails).

11. Binary inputs & outputs

The IO module is equipped to provide 4 binary outputs (normally open contact) and 13 binary
inputs (10 of which are configurable).

12. Self-diagnostic

During the running time, the device keeps a full supervision on its software and hardware,
once an abnormality is found, the device will be self-blocked to ensure no maloperation is
conducted, meanwhile, an alarm will be sent out both digitally and hardware output as alarm.
If the device is dual equipped, at this time, if the abnormal device is on-duty then it will not
only block itself but also activate the backup device to take over all the tasks to ensure the
substation is still running normally.

1.3 Features

1. High performance hardware architecture

Dual CPU >1GHz, 2 GB RAM, optional 4G micro SD or 64G SSD

Capable for data management and communication of the SAS for the whole substation or
power plant

PCS-9799 Station Manager 1-3

Date: 2015-03-31
1 Introduction

Communication ports: up to 12 Ethernet ports, 15 serial ports (supporting RS-232, RS-485,


RS-422 or MODEM)

Air cooling architecture is adopted to avoid the use of fan (motor and vibration)

Non-rotating storage is adopted to avoid vibration


A fully closed chassis with a complete panel
Completely separated spaces for electronic and electrical systems
Designed with anti-interference measures to enhance the device EMC.

2. Real-time database

Compatible for data model IEC 61850 and IEC 103

Support of multiple models including primary/secondary equipment model, association model,


primary schematic diagram model, etc.

Full modeling view and data information

Unified data acquisition and transmission

3. History database

Embedded history database

Optional capacity: 4GB micro SD or 64GB SSD (Solid State Drive)

Multiple data storage including historical SOE records, operation reports, wave files, etc.

4. Real-time data transmission

Internal SOE transmission delay <100ms

5. Unified substation model transmission

The data model transformation between substation and control center is realized by using the
SCD file.

Support of most international standard protocols including IEC60870-5-101/104, NR private


103, IEC60870-5-103, IEC 61850 and CDT.

6. Powerful auxiliary configuration tool

Highly integrated configuration functions

Full substation configuration support including project implementation, running, maintenance,


analysis, diagnostic and debugging.

7. System scale

Up to 300 IEDs

Up to 8 control centers

Database < 200,000 signals

1-4 PCS-9799 Station Manager

Date: 2015-03-31
2 Technical Data

2 Technical Data

Table of Contents
2 Technical Data .................................................................................... 2-a
2.1 Electrical Specification ................................................................................... 2-1
2.1.1 Power Supply ....................................................................................................................... 2-1

2.1.2 Binary Input .......................................................................................................................... 2-1

2.1.3 Binary Output........................................................................................................................ 2-1

2.2 Mechanical Specification ................................................................................ 2-1


2.3 Ambient Temperature and Humidity Range .................................................. 2-2
2.4 Communication Port ....................................................................................... 2-2
2.4.1 EIA-485 Port ......................................................................................................................... 2-2

2.4.2 Ethernet Port ........................................................................................................................ 2-2

2.4.3 Clock Synchronization Port .................................................................................................. 2-2

2.4.4 Modem Port .......................................................................................................................... 2-3

2.5 Type Test .......................................................................................................... 2-3


2.5.1 Environmental Test ............................................................................................................... 2-3

2.5.2 Mechanical Test .................................................................................................................... 2-3

2.5.3 Insulation Test ....................................................................................................................... 2-3

2.5.4 Electromagnetic Compatibility .............................................................................................. 2-3

2.6 Management Functions ................................................................................... 2-4


2.6.1 Clock Performance ............................................................................................................... 2-4

2.6.2 Binary Input Signal ............................................................................................................... 2-4

2.7 Certifications .................................................................................................... 2-5

PCS-9799 Station Manager 2-a

Date: 2015-03-31
2 Technical Data

2-b PCS-9799 Station Manager

Date: 2015-03-31
2 Technical Data

2.1 Electrical Specification


2.1.1 Power Supply
Standard IEC 60255-11:2008
Rated voltage 110Vdc/125Vdc, 220Vdc/250Vdc
Operating range 88~300Vdc
Permissible AC ripple voltage ≤15% of the nominal auxiliary voltage
Power consumption Classic < 45W

2.1.2 Binary Input


Rated voltage 24V 48V
Rated current 1.20mA 2.40mA
Pickup voltage 16.8-28.8Vdc 33.6-57.6Vdc
Drop-off voltage <12Vdc <24Vdc
Maximum permissible voltage 100Vdc
Withstand voltage (continu) 2000Vac, 2800Vdc
Response time ≤1ms

2.1.3 Binary Output


Contact Type Parallel Connection Single
Maximal system voltage 380Vac, 250Vdc
Voltage withstand 1000V RMS in 1min
8A@380Vac 5A@380Vac
Continuous carry
8A@250Vdc 5A@250Vdc
12A@3s 8A@3s
18A@1s 12A@1s
Short duration current
[email protected] [email protected]
[email protected] [email protected]
0.65A@48Vdc
0.35A@110Vdc
Breaking capacity (L/R=40ms) 0.30A@125Vdc
0.20A@220Vdc
0.15A@250Vdc
Pickup time < 8ms (typical 3ms)
Drop off time < 5ms
Durability 10,000 operations minimum

2.2 Mechanical Specification


Mounting Way Flush mounted
Chassis color Silver grey
Weight per device Approx. 10kg
Chassis material Aluminum alloy

PCS-9799 Station Manager 2-1

Date: 2015-03-31
2 Technical Data

Location of terminal Rear panel of the device


Device structure Plug-in modular type @ rear side, integrated front plate
Protection class
Standard IEC 60225-1:2009
HMI side IP40
Terminal side IP30
Other sides IP20 (with ventilation hole)

2.3 Ambient Temperature and Humidity Range


Standard IEC 60255-1:2009
Operating temperature -10°C to +55°C
Transport and storage
-40°C to +70°C (Readability of display may be impaired below -20°C)
temperature range
Permissible humidity 5%-95%, without condensation
Altitude <3000m

2.4 Communication Port


2.4.1 EIA-485 Port
Baud rate 4800bps, 9600bps, 19200bps, 38400bps, 57600bps, 115200bps
Protocol IEC 60870-5-103:1997
Maximal capacity 32
Transmission distance <500m
Safety level Isolation to ELV level
Twisted pair Screened twisted pair cable

2.4.2 Ethernet Port


Connecter type RJ-45
Transmission rate 100Mbits/s
Transmission standard 10Base-T/100Base-TX
Transmission distance <100m
Protocol IEC 60870-5-103:1997 or IEC 61850
Safety level Isolation to ELV level

2.4.3 Clock Synchronization Port


Type Differential RS-485
Transmission distance <500m
Maximal capacity 32
Timing standard IRIG-B
Safety level Isolation to ELV level

2-2 PCS-9799 Station Manager

Date: 2015-03-31
2 Technical Data

2.4.4 Modem Port


Port number Up to 9
Baud rate (Asynchromous) 300bps, 600bps,1200bps
Center Frequency 1200Hz, 1350Hz, 1500Hz, 1700Hz, 2880Hz, 3000Hz
Frequency Offset (±) 150Hz, 200Hz, 300Hz, 400Hz
Output Voltage 0dBm, -6dBm, -12dBm, -18dBm
Impedance 600Ω

2.5 Type Test


2.5.1 Environmental Test
Dry cold test IEC 60068-2-1: 2007
Dry heat test IEC 60068-2-2: 2007
Damp heat test, cyclic IEC 60068-2-30: 2005
Seady heat test IEC 60068-2-78: 2001

2.5.2 Mechanical Test


Vibration test IEC 60255-21-1: 1988 Class I
Shock test IEC 60255-21-2: 1988 Class I
Bump test IEC 60255-21-2: 1988 Class I
Earthquake test IEC 60255-21-3: 1993 Class I

2.5.3 Insulation Test


IEC 60255-5: 2000
Insulation resistance
> 100MΩ @500Vdc
IEC 60255-27: 2005
Dielectric withstand 2.8kV, DC, 1min
2.0kV, AC, 1min
IEC 60255-5: 2000
Impulse voltage Rated insulation voltage > 63V, impulse voltage 5kV
Rated insulation voltage < 63V, impulse voltage 1kV
Overvoltage category IEC 60255-5: 2000 Class III
Polution degree IEC 60255-1:2009 Class II
Laser safty Obvious warning sign

2.5.4 Electromagnetic Compatibility


IEC 60255-22-1:2007, Class III
1MHz burst disturbance test Common mode: 2.5kV
Differential mode: 1.0kV
IEC60255-22-2:2008 Class IV
Electrostatic discharge test For contact discharge: ±8kV
For air discharge: ±15kV
Radio frequency interference IEC 60255-22-3:2007 Class III

PCS-9799 Station Manager 2-3

Date: 2015-03-31
2 Technical Data

tests Frequency sweep


Radiated amplitude-modulated
10V/m (rms), f=80~1000MHz
IEC 60255-22-4:2008, Class IV
Fast transient disturbance
Power supply, I/O, Earth: ±4kV, 5kHz for 15ms, 100kHz for 0.75ms
tests
Communication terminals: ±2kV, 5kHz for 15ms, 100kHz for 0.75ms
IEC 60255-22-5:2008, Class IV
Power supply, AC input, I/O port: 1.2/50μs
Surge immunity test
Common mode: ±4kV
Differential mode: ±2kV
Power frequency magnetic IEC 61000-4-8:2001, Class V
field immunity 100A/m for 1min, 1000A/m for 3s
IEC 61000-4-9:2001, Class V
Pulse magnetic field immunity
6.4/16μs, 1000A/m
IEC 60255-22-6:2001, Class III
Conducted RF
Power supply, AC, I/O, Comm. Terminal: 10Vrms, 150kHz~80MHz
electromagnetic disturbance
Spot frequency, f=27MHz/68MHz
IEC 60255-22-7:2003, Class A
Power frequency immunity Common mode: 300V
Differential mode: 150V
IEC 60255-25:2000, Class A
Conducted emission
f=0.15MHz~0.5MHz/0.5kHz~30MHz
IEC 60255-25:2000, Class A
Radiated emission
f=30MHz~230MHz/230MHz~1000MHz
Damped oscillatory magnetic IEC 61000-4-10:2001, Class V
field immunity 100kHz & 1MHz, 100A/m
Auxiliary power supply
performance IEC60255-11: 2008
- Voltage dips Up to 200ms for dips to 40% of rated voltage without reset
- Voltage short interruptions

2.6 Management Functions


2.6.1 Clock Performance
Real time clock accuracy ≤ 3s/day
Accuracy of GPS synchronization ≤ 1ms
External time synchronization IRIG-B (200-98)

2.6.2 Binary Input Signal


Resolution of binary input signal ≤ 1ms
Binary input mode Potential-free contact
Resolution of SOE ≤ 2ms

2-4 PCS-9799 Station Manager

Date: 2015-03-31
2 Technical Data

2.7 Certifications
1. ISO9001:2008

2. ISO14001:2004

3. OHSAS18001:2007

4. ISO10012:2003

5. CMMI L5

6. EMC: 2004/108/EC, EN50263:1999

7. Products safety (PS): 2006/95/EC, EN61010-1:2001

PCS-9799 Station Manager 2-5

Date: 2015-03-31
2 Technical Data

2-6 PCS-9799 Station Manager

Date: 2015-03-31
3 Operation Theory

3 Operation Theory

Table of Contents
3 Operation Theory ............................................................................... 3-a
3.1 Software Structure ........................................................................................... 3-1
3.2 Functions ......................................................................................................... 3-1

PCS-9799 Station Manager 3-a

Date: 2015-03-31
3 Operation Theory

3-b PCS-9799 Station Manager

Date: 2015-03-31
3 Operation Theory

3.1 Software Structure


The PCS-9799 Station Manager applies embedded Linux software platform. The modularization
software design provides high flexibility and applicability.

The software structure is shown in following figure:

Configuration Advanced
IEC 101/104 (Server)
Tool (PC) Application

Keypad
Operation

Database Binary input


& output
LCD
Display

Logical &
mathematical
IEC 61850 (Client) NR Private & IEC 103 (Client) processing

3.2 Functions
No. Subsystem Description
1 Database Data acquisition and management (server and client).
Communication to master station (control center, distribution center, etc.)
Modeling of the whole substation
Data transmission to master station via server protocol (IEC 101/104, CDT,
2 Server protocol
etc.)
Response to master station's interrogation
Transmission of remote control command.
Communication to IED within the substation
Data acquisition from IED via client protocol (IEC 61850/103, NR private 103,
3 Client protocol
etc.)
Processing of remote control command
Edition and analysis of synthesized signal
4 Logical processing
Logical processing of control block logic
Acquisition of binary input status
5 Binary input & output
Output contact based on device's states
LCD display, LED indicators, keypad and configuration tool to realize the
6 Human-machine interaction supervision of running status, communication messages, parameters &
settings, project configuration, diagnostic & analysis
7 Advanced application Advanced customized functions for special requirement.
8 Time synchronization IRIG-B signal reception

PCS-9799 Station Manager 3-1

Date: 2015-03-31
3 Operation Theory

3-2 PCS-9799 Station Manager

Date: 2015-03-31
4 Supervision

4 Supervision

Table of Contents

4.1 Overview ........................................................................................................... 4-1


4.2 Supervision Alarms ......................................................................................... 4-1

List of Tables

Table 4.1-1 Alarm description .................................................................................................... 4-1

Table 4.1-2 Troubleshooting ........................................................................................................ 4-2

PCS-9799 Station Manager


4-1

Date: 2015-03-31
4 Supervision

PCS-9799 Station Manager


4-2
Date: 2015-03-31
4 Supervision

4.1 Overview

The PCS-9799 Station Manager is in quiescent state under normal conditions, and it is required to
respond promptly for faults. When the device is in energizing process before the LED “HEALTHY”
is on, the device need to be checked to ensure no abnormality. Therefore, the automatic
supervision function, which checks the health of the protection system when startup and during
normal operation, plays an important role.

This device based on the microprocessor operations is suitable for implementing this automatic
supervision function of the system.

In case a defect is detected during initialization when DC power supply is provided to the device,
the device will be blocked with indication and alarm of device out of service.

When a failure is detected by the automatic supervision, it is followed by a LCD message, LED
indication and alarm contact outputs. The failure alarm is also recorded in event recording report
and can be printed if required.

4.2 Supervision Alarms

Hardware circuit and operation status of the device are self-supervised continuously. If any
abnormal condition is detected, information or report will be displayed and a corresponding alarm
will be issued.

A minor abnormality may block a certain number of functions while the other functions can still
work. However, if severe hardware failure or abnormality, such as PWR module failure, DC
converter failure and so on, are detected, all functions will be blocked and the LED “HEALTHY”
will be extinguished. The device then cannot work normally and maintenance is required to
eliminate the failure. All the alarm signals and the corresponding handling suggestions are listed
below.

Note!

If the device is blocked or alarm signal is sent during operation, please do find out its
reason with the help of self-diagnostic record. If the reason cannot be found at site, a trial
recovery of the device by re-energization is suggested. Please contact the supplier if the
device is still failure.

Table 4.2-1 Alarm description

No. Item Description Blocking Device


Fail Signals
The signal is always issued when a certain hardware
1 Alm_Brd_Overall error is detected, the device will be blocked and all the Blocked
functions are not available.

PCS-9799 Station Manager


4-1

Date: 2015-03-31
4 Supervision

Alarm Signals
2 Alm_Process The certain module of the program is abnormal. Unblocked
3 Alm_Insuf_Disk The ROM is not enough for the data storage. Unblocked
4 Alm_RecvMON1 The data synchronization module1 is out of service. Unblocked
5 Alm_RecvMON2 The data synchronization module2 is out of service. Unblocked
6 Alm_RecvMON3 The data synchronization module3 is out of service. Unblocked
7 Alm_RecvMON4 The data synchronization module4 is out of service. Unblocked
When running in the dual-device mode, the configuration
8 Alm_Cfg_DualDev_Diff Unblocked
files of two devices are not consistent.
The on-duty configuration file and the backup
9 Alm_Cfg_Backup_Diff configuration files are not consistent (the time stamp of Unblocked
these two files are not same).
When running in the dual-device mode, the programs
10 Alm_MON1_DualDev_Diff running on the MON module 1 of the two devices are not Unblocked
consistent.
Within one device, the programs running on the MON
11 Alm_MON2/MON1_Diff module 2 and the one on MON module 1 are not Unblocked
consistent.
Within one device, the programs running on the MON
12 Alm_MON3/MON1_Diff module 3 and the one on MON module 1 are not Unblocked
consistent.
Within one device, the programs running on the MON
13 Alm_MON4/MON1_Diff module 4 and the one on MON module 1 are not Unblocked
consistent.
One of the power supply of device is in abnormal state.
14 Alm_Pwr_Device (available when the device is working in dual-power Unblocked
supply mode)
There is invalid configuration in the configuration
15 Alm_Cfg_Invalid Unblocked
database.

Table 4.2-2 Troubleshooting

No. Item Handling suggestion


Fail Signals
The signal is always issued when a certain hardware error is detected, the
device will be blocked and all the functions are not available, please check the
1 Alm_Brd_Overall
hardware of the device (module misplaced, module loose etc.) and contact the
manufacturer.
Alarm Signals
2 Alm_Process Generally it will recover automatically, if not, please contact the manufacturer.
3 Alm_Insuf_Disk Generally it will recover automatically, if not, please contact the manufacturer.
4 Alm_RecvMON1 Generally it will recover automatically, if not, please contact the manufacturer.
5 Alm_RecvMON2 Generally it will recover automatically, if not, please contact the manufacturer.
6 Alm_RecvMON3 Generally it will recover automatically, if not, please contact the manufacturer.

PCS-9799 Station Manager


4-2
Date: 2015-03-31
4 Supervision

7 Alm_RecvMON4 Generally it will recover automatically, if not, please contact the manufacturer.
Please check the configuration files or re-download the same file into the two
8 Alm_Cfg_DualDev_Diff
devices.
9 Alm_Cfg_Backup_Diff Please re-download the latest configuration file into the device and reboot.
10 Alm_MON1_DualDev_Diff Please contact the manufacturer to update the program of the two devices.
11 Alm_MON2/MON1_Diff Please contact the manufacturer to update the program of the device.
12 Alm_MON3/MON1_Diff Please contact the manufacturer to update the program of the device.
13 Alm_MON4/MON1_Diff Please contact the manufacturer to update the program of the device.
14 Alm_Pwr_Device Please check the power supply of the device.
15 Alm_Cfg_Invalid Please check the configuration database.

PCS-9799 Station Manager


4-3

Date: 2015-03-31
4 Supervision

PCS-9799 Station Manager


4-4
Date: 2015-03-31
5 Management

5 Management

Table of Contents
5 Management ....................................................................................... 5-a
5.1 Real Time Data Interrogation .......................................................................... 5-1
5.1.1 IO Status ............................................................................................................................... 5-1

5.1.2 Measurement........................................................................................................................ 5-1

5.1.3 Tap Position .......................................................................................................................... 5-1

5.1.4 Meterage .............................................................................................................................. 5-1

5.1.5 Device Settings..................................................................................................................... 5-1

5.1.6 Setting Group ....................................................................................................................... 5-1

5.1.7 Setting .................................................................................................................................. 5-1

5.2 Event Recording .............................................................................................. 5-2


5.2.1 SOE Records........................................................................................................................ 5-2

5.2.2 Operation Logs ..................................................................................................................... 5-2

PCS-9799 Station Manager 5-a

Date: 2015-03-31
5 Management

5-b PCS-9799 Station Manager

Date: 2015-03-31
5 Management

5.1 Real Time Data Interrogation


This device can display (with the optional LCD) the IO status, measurement & metering values,
settings & parameters of the device itself or a connected IED by the means of network
interrogation.

5.1.1 IO Status
"MainMenu"-> "Database"->"Online"->"Datatype01"

The device's or connected IED's status of the binary inputs, output contacts, certain device alarm
and network communication connection state can be interrogated and viewed.

5.1.2 Measurement
"MainMenu"-> "Database"->"Online"->"Datatype02"

This device can perform continuous measurement of analogue input with optional AC AI module. It
samples 80 points per cycle and calculates the RMS value in each interval. The optional LCD
display is updated in every 0.5 second. The measurement data can also be transmitted to a
local/remote PC via communication protocol.

The device's or connected IED's measured values, including both AC & DC analog inputs, can be
interrogated and viewed.

5.1.3 Tap Position


"MainMenu"-> "Database"->"Online"->"Datatype03"

The device's or connected IED's transduced tap position can be interrogated and viewed.

5.1.4 Meterage
"MainMenu"-> "Database"->"Online"->"Datatype04"

The device's or connected IED's metering values can be interrogated and viewed.

5.1.5 Device Settings


"MainMenu"-> "Database"->"Online"->"Datatype05"

The device's or connected IED's device settings can be interrogated and viewed.

5.1.6 Setting Group


"MainMenu"-> "Database"->"Online"->"Datatype06"

A connected IED's (protection relay) setting group, including the active setting group and the
editing setting group, can be interrogated and viewed.

5.1.7 Setting
"MainMenu"-> "Database"->"Online"->"Datatype07"

The device's or connected IED's parameter can be interrogated and viewed.

PCS-9799 Station Manager 5-1

Date: 2015-03-31
5 Management

5.2 Event Recording


The device can store enormous SOE (Sequence Of Events) records and device logs of this device
itself and all the connected IED in its inner integrated database. All the records are stored
(seperated by their different addresses and record groups) in non-volatile memory and follow the
FIFO principle (First In First Out, when the available space is exhausted, the oldest record will be
automatically overwritten by the latest one).

5.2.1 SOE Records


1. IO Events

"MainMenu"-> "Database"->"Records"->"SOE Records"->"Datatype01"

When a binary input is energized or de-energized, i.e., its state has changed from "0" to "1" or
from "1" to "0", it will be stored and displayed.

2. Supervision Events

"MainMenu"-> "Database"->"Records"->"SOE Records"->"Datatype02"

The device is under automatic supervision all the time. If there is any failure or abnormal
condition detected (E.g. VT circuit failure, abnormal power supply of BI module), it will be
stored and displayed.

3. Disturbance Records

"MainMenu"-> "Database"->"Records"->"SOE Records"->"Datatype03"

When any protection element operates or drops off, such as fault detector, distance protection
etc., they will be logged in disturbance records.

5.2.2 Operation Logs


1. Control Logs

"MainMenu"-> "Database"->"Records"->"Operation Logs"->"Datatype01"

The total sequence of each attempt of control command will be stored and displayed,
including object, source, remote/local mode, interlock condition, command
(selection/execution, open/close, up/down) and result.

5-2 PCS-9799 Station Manager

Date: 2015-03-31
6 Hardware

6 Hardware

Table of Contents
6 Hardware ............................................................................................6-a
6.1 Overview .......................................................................................................... 6-1
6.2 MON Module (Management & Monitoring) .................................................... 6-2
6.3 IO Module (Binary Input and Output)............................................................. 6-4
6.4 COM Module (Extension Communication Ports) .......................................... 6-7
6.5 PWR Module (Power Supply) ....................................................................... 6-13
6.6 HMI Module (Human-Machine Interface) ..................................................... 6-14

List of Figures
Figure 6.1-1 Front view ............................................................................................................... 6-2

Figure 6.1-2 Rear view ................................................................................................................ 6-2

Figure 6.1-3 Module configuration ............................................................................................ 6-2

Figure 6.2-1 MON module........................................................................................................... 6-3

Figure 6.2-2 Wiring of synchronization port ............................................................................ 6-4

Figure 6.3-1 IO module ............................................................................................................... 6-5

Figure 6.3-2 Wiring for dual device inter-block ....................................................................... 6-6

Figure 6.4-1 COM Module (NR1224) .......................................................................................... 6-7

Figure 6.4-2 COM Module (NR1225) ........................................................................................ 6-11

Figure 6.5-1 PWR module......................................................................................................... 6-13

PCS-9799 Station Manager


6-a

Date: 2014-10-15
6 Hardware

PCS-9799 Station Manager


6-b
Date: 2014-10-15
6 Hardware

6.1 Overview
PCS-9799 is designed based on the new generation of UAPC platform. It adopts 32-bit dual-core
high preference processor as its central unit for the communication management, database
arrangement, advanced application, analysis and fault detection. Meanwhile, it adopts DDR2
RAM to ensure the real-time and high-speed calculation. With the massive storage disk, the
hardware is highly integrated which gives the device high extensibility and maintainability. The
internal data bus is based on high-speed Ethernet, which makes sure the communication
between each module is very efficient, enables the distribute computing, balances the system
load and enhances the system extensibility.

This device consists of several different modules. The application and terminal description of each
module are introduced below.

Slot No. Module Type Brief


01 NR1108 MON module, management and monitor module
12 NR1525 IO module, binary input and output module
NR1224, COM module, extension serial ports and modem ports module for
13, 14, 15
NR1225 communication
NR4304,
P1 PWR module, power supply module
NR4305
HMI module, human-machine interface

 MON module provides functions like communication with SAS, event record, setting
management etc. The medium of the Ethernet interface of the MON module is optional.

 IO module provides output contacts and binary inputs via opto-couplers.

 COM module provides up extension serial ports or modem ports for communication with other
device or control system.

 PWR module converts the power supply into various DC voltage levels for different modules
and components in the device.

 HMI module human-machine interface is comprised of LCD, keypad, LED indicators and a
multiplex RJ45 port for debugging.

Note!

In different engineering applications, the arrangement of equipped modules is different


according to the actual requirements.

The following figures will show the example views of the device.

PCS-9799 Station Manager


6-1

Date: 2014-10-15
6 Hardware

HEALTHY

ALARM
PCS-9799
REMOTE STATION MANAGER
CO-DEV OK

SYNC

ENT

Figure 6.1-1 Front view

NR11 08 NR15 25 NR 12 25 NR12 24 NR13 01


5V OK ALM

BO_ALM BO_FAIL

ON

OF F

1 BO _ CO M1
2 BO _ FAIL

3 BO_ AL M

4 BO_ CO M2

5 BO_ FAIL

6 BO _ AL M

7 O PTO+

8 O PTO-

9
10 PWR+

11 PWR-

12 G ND

Figure 6.1-2 Rear view

NR1108 NR1525 NR1224 NR1224 NR1301


COM Module 2
COM Module 1

PWR module 1
MON module

IO Module
Reserve

Reserve

Reserve
Reserve

Reserve

Reserve

Reserve

Reserve
Reserve
Reserve

Slot No.
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 P1

Figure 6.1-3 Module configuration

6.2 MON Module (Management & Monitoring)


The MON module is obligatory and fixed at the first chassis slot 01.

The MON module consists of high-performance built-in processor, FLASH, SRAM, SDRAM,
Ethernet controller and other peripherals. Its functions include management of the complete

PCS-9799 Station Manager


6-2
Date: 2014-10-15
6 Hardware

device, human machine interface, communication and waveform recording, etc.

The MON module uses the internal bus to receive data from other modules. It communicates with
the LCD module by RS-485 bus.

6 Ethernet Port
NR1108

1 Ethernet Port1

2 Ethernet Port2

3 Ethernet Port3

4 Ethernet Port4

5 Ethernet Port5

6 Ethernet Port6

1
GPS IRIG-B Signal
2 SYN+
GPS
Input 3 SYN-

4 SGND

NR1108 12 Ethernet Port

1 Ethernet Port1 7 Ethernet Port7

2 Ethernet Port2 8 Ethernet Port8

3 Ethernet Port3 9 Ethernet Port9

4 Ethernet Port4 10 Ethernet Port10

5 Ethernet Port5 11 Ethernet Port11

6 Ethernet Port6 12 Ethernet Port12

1
GPS IRIG-B Signal
2 SYN+
GPS
Input 3 SYN-

4 SGND

Figure 6.2-1 MON module

Several different types of the MON module are optional:

PCS-9799 Station Manager


6-3

Date: 2014-10-15
6 Hardware

Type RAM Storage Ethernet Port


NR1108C 2G 4G 6
NR1108D 2G 4G 12
NR1108CD 2G 64G 6
NR1108DD 2G 64G 12

The correct wiring is shown in the following figure. Generally, the shielded cable with two pairs of
twisted pairs inside shall be applied. One pair of the twisted pairs are respectively used to connect
the "+" and "–" terminals of difference signal. The other pair of twisted pairs is used to connect the
signal ground of the communication interface. The module reserves a free terminal for all the
communication ports. The free terminal has no connection with any signal of the device, and it is
used to connect the external shields of the cable when connecting multiple devices in series. The
external shield of the cable shall be grounded at one of the ends only.

Twisted pair wire


SYN+ 01

GPS Input
SYN- 02

SGND 03
To the screen of other coaxial 04
cable with single point earthing

Figure 6.2-2 Wiring of synchronization port

6.3 IO Module (Binary Input and Output)


The IO module provides 4 output contacts and 13 binary inputs (10 of which are configurable).

The IO module NR1525 has a 22-pin connector.

PCS-9799 Station Manager


6-4
Date: 2014-10-15
6 Hardware

01
BO_1
NR1525 02

03
BO_2
04

05
BO_3
06

07
BO_4
08

BI_Mainte nance 09

BI_Rmt/Loc 10

BI_Co-DevBlk d 11

BI_4 12

BI_5 13

BI_6 14

BI_7 15

BI_8 16

BI_9 17

BI_10 18

BI_11 19

BI_12 20

BI_13 21

Opto- 22

Figure 6.3-1 IO module

Pin No. Symbol Description


1
BO_1 Output contact 1 (NO)
2
3
BO_2 Output contact 2 (NO)
4
5
BO_3 Output contact 3 (NO)
6
7
BO_4 Output contact 4 (NO)
8
9 BI_Maintenance Binary input for the indication of device maintenance state
10 BI_Rmt/Loc Binary input to switch the remote/local control mode
11 BI_Co-DevBlkd Binary input for the indication of co-operate device's block
12 BI_4
13 BI_5
14 BI_6 Configurable binary input
15 BI_7
16 BI_8

PCS-9799 Station Manager


6-5

Date: 2014-10-15
6 Hardware

Pin No. Symbol Description


17 BI_9
18 BI_10
19 BI_11
20 BI_12
21 BI_13
22 Opto- Common negative pole of binary input.

1. Binary input: [BI_Maintenance]

It is used to block communication export when this binary input is energized. During device
maintenance or testing, this binary input is then energized not to send reports via
communication port, local display and printing still work as usual. This binary input should be
de-energized when the device is restored back to normal.

2. Binary input: [BI_Rmt/Loc]

It is used to select the remote control or the local control.

If it is energized (the remote control), all the binary outputs can be remotely controlled by
control center.

3. Binary input: [BI_Co-DevBlkd]

It is used to identify that the cooperation device is blocked (when dual-device configuration is
applied). This module can realize the inter-block between the on-duty device and backup
device. The wiring is shown in following figure.

Device A Device B
IO IO
01 01
BO_1 BO_1
02 02

03 03
BO_2 BO_2
04 04

05
PWR PWR 05
BO_3 BO_3
06 06
NR1301 NR1301
07 07
BO_4 5 V OK ALM 5 V OK ALM
BO_4
08 08

BI_Mainte nance 09 BI_Mainte nance 09


BO_ ALM BO_ FAIL BO_ALM BO_ FAIL
BI_Rmt/Loc 10 BI_Rmt/Loc 10

BI_Co-DevBlk d 11 BI_Co-DevBlk d 11

BI_4 12 BI_4 12

BI_5 13 BI_5 13
1 BO_ COM1 1 BO_ COM1

BI_6 14 2 BO_ FAIL 2 BO_ FAIL BI_6 14

BI_7 15 3 BO_ ALM 3 BO_ ALM BI_7 15

4 BO_ COM2 4 BO_ COM2


BI_8 16 BI_8 16
5 BO_ FAIL 5 BO_ FAIL
BI_9 17 BI_9 17
6 BO_ ALM 6 BO_ALM
BI_10 18
7 OPTO+ 7 OPTO+ BI_10 18

BI_11 19 8 OPTO- 8 OPTO- BI_11 19

9 9
BI_12 20 BI_12 20
10 PWR+ 10 PWR+
BI_13 21 BI_13 21
11 PWR- 11 PWR-
Opto- 22 Opto- 22
12 GND 12 GND

Figure 6.3-2 Wiring for dual device inter-block

PCS-9799 Station Manager


6-6
Date: 2014-10-15
6 Hardware

6.4 COM Module (Extension Communication Ports)


The COM module provides several extension serial ports or modem ports

Note!

The device supports at most 3 COM modules, the COM modules can be applied in slot
13, 14, 15.

 NR1224

This module provides 5 serial ports (RS-232/RS-485), besides, the No.5 port can be set as
RS-422.

01 TX/A

NR1224 02 RX/B
RS-232/485
03 SGND

04 SHLD

05 TX/A

06 RX/B
RS-232/485
07 SGND

08 SHLD

09 TX/A

10 RX/B
RS-232/485
11 SGND

12 SHLD

13 TX/A

14 RX/B
RS-232/485
15 SGND

16 SHLD

17 TX/A

18 RX/B

19 SGND
RS-232/485
/422
20 SHLD

21 Y

22 Z

Figure 6.4-1 COM Module (NR1224)

Pin No. Symbol Description Port No.


RS-232: TX (Send)
01 TX/A
RS-485: A
RS-232: RX (Receive)
02 RX/B Serial port 1
RS-485: B
03 SGND Signal ground
04 SHLD Shielded layer

PCS-9799 Station Manager


6-7

Date: 2014-10-15
6 Hardware

Pin No. Symbol Description Port No.


RS-232: TX (Send)
05 TX/A
RS-485: A
RS-232: RX (Receive)
06 RX/B Serial port 2
RS-485: B
07 SGND Signal ground
08 SHLD Shielded layer
RS-232: TX (Send)
09 TX/A
RS-485: A
RS-232: RX (Receive)
10 RX/B Serial port 3
RS-485: B
11 SGND Signal ground
12 SHLD Shielded layer
RS-232: TX (Send)
13 TX/A
RS-485: A
RS-232: RX (Receive)
14 RX/B Serial port 4
RS-485: B
15 SGND Signal ground
16 SHLD Shielded layer
RS-232: TX (Send)
17 TX/A
RS-485,RS-422: A
RS-232: RX (Receive)
18 RX/B
RS-485,RS-422: B
Serial port 5
19 SGND Signal ground
20 SHLD Shielded layer
21 Y RS-422: Y
22 Z RS-422: Z

The mode option of each serial port is realized by the corresponding jumpers which locate on
the COM module. The configuration detail of each port is listed in the following tables (the
black background means connected pins by the jumper).

 Serial port 1

Jumper RS-485 RS-232


1 2 3 1 2 3
P7

1 2 3 1 2 3
P8

1 2 3 1 2 3
P9

1 2

1 2
P5
1 2

PCS-9799 Station Manager


6-8
Date: 2014-10-15
6 Hardware

 Serial port 2

Jumper RS-485 RS-232


1 2 3 1 2 3
P12

1 2 3 1 2 3
P13

1 2 3 1 2 3
P14

1 2

1 2
P10
1 2

 Serial port 3

Jumper RS-485 RS-232


1 2 3 1 2 3
P17

1 2 3 1 2 3
P18

1 2 3 1 2 3
P19

1 2

1 2
P15
1 2

 Serial port 4

Jumper RS-485 RS-232


1 2 3 1 2 3
P22

1 2 3 1 2 3
P23

1 2 3 1 2 3
P24

1 2

1 2
P20
1 2

 Serial port 5

Jumper RS-485 RS-232 RS-422


1 2 3 1 2 3 1 2 3
P27

PCS-9799 Station Manager


6-9

Date: 2014-10-15
6 Hardware

Jumper RS-485 RS-232 RS-422


1 2 3 1 2 3 1 2 3
P28

1 2 3 1 2 3 1 2 3
P29

1 2 3 1 2 3 1 2 3
P30

1 2 1 2 1 2
P31

1 2 1 2 1 2
P32

1 2

1 2 1 2
P25
1 2

1 2

1 2 1 2
P33
1 2

Note!

When the port 1 is used as RS-485 port, the P5 is used as matched resistance. Normally
the jumper is not necessary. If the communication quality is not good enough, users can
use P5 to enhance the quality. Similar principles are adopted for the other ports.

Port 2 as RS-485: P10 as matched resistance

Port 3 as RS-485: P15 as matched resistance

Port 4 as RS-485: P25 as matched resistance

Port 5 as RS-422: P33 as matched resistance

 NR1225

This module provides 2 serial ports (RS-232/RS-485) and 3 modem ports.

PCS-9799 Station Manager


6-10
Date: 2014-10-15
6 Hardware

01 TX/A

NR1225 02 RX/B
RS-232/485
03 SGND

04 SHLD

05 TX/A

06 RX/B RS-232/485

07 SGND

08 TX+

09 TX-

10 RX+ MDM1

11 RX-

12 GND

13 TX+

14 TX-

15 RX+ MDM2

16 RX-

17 GND

18 TX+

19 TX-

20 RX+ MDM3

21 RX-

22 GND

Figure 6.4-2 COM Module (NR1225)

Pin No. Symbol Description Port No.


RS-232: TX (Send)
01 TX/A
RS-485: A
RS-232: RX (Receive)
02 RX/B Serial port 1
RS-485: B
03 SGND RS-232/RS-485 signal ground
04 SHLD RS-232/RS-485 shield layer
RS-232: TX(Send)
05 TX/A
RS-485: A
RS-232: RX(Receive) Serial port 2
06 RX/B
RS-485: B
07 SGND RS-232/RS-485 signal ground
08 TX+ Modem Send +
09 TX- Modem Send -
10 RX+ Modem Receive + Modem port 1
11 RX- Modem Receive -
12 GND Modem signal ground
13 TX+ Modem Send + Modem port 2

PCS-9799 Station Manager


6-11

Date: 2014-10-15
6 Hardware

Pin No. Symbol Description Port No.


14 TX- Modem Send -
15 RX+ Modem Receive +
16 RX- Modem Receive -
17 GND Modem signal ground
18 TX+ Modem Send +
19 TX- Modem Send -
20 RX+ Modem Receive + Modem port 3
21 RX- Modem Receive -
22 GND Modem signal ground

 Serial port 1

Jumper RS-485 RS-232


1 2 3 1 2 3
P7

1 2 3 1 2 3
P8

1 2 3 1 2 3
P9

1 2

1 2
P5
1 2

 Serial port 2

Jumper RS-485 RS-232


1 2 3 1 2 3
P12

1 2 3 1 2 3
P13

1 2 3 1 2 3
P14

1 2

1 2
P10
1 2

Note!

When the port 1 is used as RS-485 port, the P6 is used as matched resistance. Normally
the jumper is not necessary. If the communication quality is not good enough, users can
use P5 to enhance the quality. Similar principle is adopted for the other port.

Port 2 as RS-485: P11 as matched resistance


PCS-9799 Station Manager
6-12
Date: 2014-10-15
6 Hardware

6.5 PWR Module (Power Supply)


The PWR module is a DC/DC or AC/DC converter with electrical insulation between the input and
output. It has an input voltage range as described in the chapter 2. The tolerance of the output
voltage for the electronic components is continuously monitored.

The use of an external miniature circuit breaker is recommended. The miniature circuit breaker
must be in the on position when the device is in operation and in the off position when the device
is in cold reserve.

A 12-pin connector is fixed on the PWR module at the slot P1. The pin definition of the connector
is described as below.

NR1301

5V OK ALM

BO_ALM BO_FAI L

ON

OFF

1 BO_COM1
P101
2 BO_FAIL BO_FAIL1
3 BO_ALM P102
4 BO_COM2
BO_ALM1
P103
5 BO_FAIL
6 BO_ALM
7 OPTO+
P104
BO_FAIL2
8 OPTO- P105
9 BO_ALM2
10 PWR+
P106
11 PWR-
12 GND

Figure 6.5-1 PWR module

Pin No. Symbol Description

01 BO_COM1 Common terminal 1

02 BO_FAIL Indication of device failure 1 (01-02, NC)

03 BO_ALM Indication of device abnormality alarm 1 (01-03, NO)

04 BO_COM2 Common terminal 2

05 BO_FAIL Indication of device failure 2 (04-05, NC)

06 BO_ALM Indication of device abnormality alarm 2 (04-06, NO)

07 OPTO+ Positive pole of power supply for low-voltage opto-coupler (24V)

08 OPTO- Negative pole of power supply for low-voltage opto-coupler (24V)

PCS-9799 Station Manager


6-13

Date: 2014-10-15
6 Hardware

Pin No. Symbol Description

09 Not used

10 PWR+ Positive pole of power supply for device

11 PWR- Negative pole of power supply for device

12 GND Grounded connection of device

Note!

The standard rated voltage of PWR module is self-adaptive to 88~300Vdc. For


non-standard rated voltage power supply module, please specify when placing order and
check if the rated voltage of power supply module is the same as the voltage of power
source before the device being put into service.

The PWR module provides the terminal 12 and grounding screw for device grounding.
The terminal 12 shall be connected to grounding screw and then connected to the earth
copper bar of panel via dedicated grounding wire.

Effective grounding is the most important measure for a device to prevent EMI, so it must
be ensured before the device is put into service.

This device, like all electronic equipments, contains electrolytic capacitors. These
capacitors are well known to be subject to deterioration over time if voltage is not applied
periodically. Deterioration can be avoided by powering the device up once a year.

6.6 HMI Module (Human-Machine Interface)


The HMI module consists of liquid crystal display screen, keypad, LED indicators and RJ-45
debugging port. The contained ARM processor works for display controlling of LCD, keypad
processing, and exchanging data with the MON module. The optional LCD screen is a
high-performance grand liquid crystal panel with back lighting, which has a user-friendly interface
and an extensive display range.

PCS-9799 Station Manager


6-14
Date: 2014-10-15
7 Settings

7 Settings

Table of Contents
7 Settings .............................................................................................. 7-a
7.1 Overview .......................................................................................................... 7-1
7.2 Communication Settings ................................................................................ 7-1
7.3 Identification Settings..................................................................................... 7-1

PCS-9705 Bay Control Unit 7-a

Date: 2015-03-31
7 Settings

7-b PCS-9705 Bay Control Unit

Date: 2015-03-31
7 Settings

7.1 Overview
Setting configuration is an important function of device. The device normal operation depends in
the correct setting configuration. Thus, only a qualified technician should be responsible for the
configuration. Furthermore, if the device is operating abnormally, please check the setting
configuration firstly.

Note!

According to different applications in different engineering requirements, displayed settings


may be different.

7.2 Communication Settings


Access path: "MainMenu" -> "Settings" -> "Comm Settings" -> "IP"

No. Item Range Description


1 Net**-IP** 000.000.000.000~255.255.255.255 The IP address of Ethernet port
The subnet mask of the corresponding
2 Mask 000.000.000.000~255.255.255.255
Ethernet port

Access path: "MainMenu" -> "Settings" -> "Comm Settings" -> "MAC"

No. Item Range Description


The hexadecimal Media Access Control
1 Net** 00:00:00:00:00:00~ff:ff:ff:ff:ff:ff:ff
Address of the corresponding Ethernet port

Access path: "MainMenu" -> "Settings" -> "Comm Settings" -> "Route"

No. Item Range Description


1 Local router 000.000.000.000~255.255.255.255 The IP address of local router

2 Remote segment 000.000.000.000~255.255.255.255 The router's network segment (opposite side)


3 Remote mask 000.000.000.000~255.255.255.255 The router's subnet mask (opposite side)

7.3 Identification Settings


Access path: "MainMenu" -> "Settings" -> "ID Settings"

No. Item Range Description


1 Manager ID 0~999 The identification of this device in the network
The identification of this device in dual-device
2 Co-Dev ID 00 or 01
mode

1. Manager ID

This setting should be different with the other communication management device (i.e.
PCS-9794 Protocol Converter, RCS-9698 Gateway) in the same network.

PCS-9705 Bay Control Unit 7-1

Date: 2015-03-31
7 Settings

2. Co-Dev ID

This setting is only valid if the dual-device mode is applied. The 2 devices should share the
same "Manager ID" in the same network and have different "Co-Dev ID".

7-2 PCS-9705 Bay Control Unit

Date: 2015-03-31
8 Human Machine Interface

8 Human Machine Interface

Table of Contents
8.1 Overview ·······················································································8-1
8.1.1 Design .................................................................................................................................. 8-1

8.1.2 Keypad ................................................................................................................................. 8-1

8.1.3 LED Indicator ....................................................................................................................... 8-2

8.1.4 Front Debugging Port........................................................................................................... 8-3

8.1.5 Ethernet Port Setup ............................................................................................................. 8-4

8.2 LCD Display ···················································································8-4


8.3 Menu Tree ·····················································································8-5
8.3.1 Main Menu ........................................................................................................................... 8-5

8.3.2 Device State ......................................................................................................................... 8-6

8.3.3 Database .............................................................................................................................. 8-6

8.3.4 Settings ................................................................................................................................ 8-7

8.3.5 Local Command ................................................................................................................... 8-8

8.3.6 Information ........................................................................................................................... 8-8

8.3.7 Test ....................................................................................................................................... 8-8

8.3.8 Clock .................................................................................................................................... 8-9

8.3.9 Language ............................................................................................................................. 8-9

PCS-9799 Station Manager 8-a

Date: 2015-03-31
8 Human Machine Interface

8-b PCS-9799 Station Manager

Date: 2015-03-31
8 Human Machine Interface

8.1 Overview

Operator can access the device from the HMI panel. Local communication with the device is
possible in using a computer via the multiplex RJ45 port on the HMI panel. Furthermore, remote
communication is also possible in using a PC with the SCADA via a RS485 port or a Ethernet port
on the MON module.

This chapter describes the human machine interface (HMI), and gives out an instruction about
how to display or print event report, setting and so on through HMI menu tree and display
metering value, including r.m.s. current, voltage and frequency etc. through LCD. Procedure to
change active setting group or a settable parameter value through keypad is also described in
details.

8.1.1 Design
The human-machine interface (HMI) module which allows a communication to be as simple as
possible for the user. The HMI module helps to draw your attention to something that has
occurred which may activate an LED or a report displayed on the LCD. Operator can locate the
data of interest by navigating the keypad.

No. Item Description


A 320×240 dot matrix backlight LCD display is visible in dim lighting
1 LCD conditions. The corresponding messages are displayed when any operation
implemented.
2 LED 20 status indication LEDs in which the first 5 are fixed.
3 Keypad Navigation keypad and 9 keys
4 Communication port A multiplex RJ45 port for debugging

8.1.2 Keypad
ESC UN

+
F

ENT
-

1. "ESC"

 Cancel the operation

 Quit the current menu

2. "ENT"

 Execute the operation

 Confirm the interface

PCS-9799 Station Manager 8-1

Date: 2015-03-31
8 Human Machine Interface

3. "FUN"

 Activate the switching function

4. "◄" and "►"

 Move the cursor horizontally

 Enter the next menu or return to the previous menu

5. "▲" and "▼"

 Move the cursor vertically

 Select command menu within the same level of menu

6. "+" and "-"

 Modify the value

 Modify and display the message number

 Page up/down

8.1.3 LED Indicator

1 11
HEAL THY
2 12
ALARM

3 13
REM OTE
4 14
CO-DEV O K
5 15
S YNC
6 16

7 17

8 18

9 19

10 20

A brief explanation has been made as bellow.

LED Display Description

Off The device is out of service or any hardware error is defected during self-check.
HEALTHY
Green The device is in service and ready for operation.

Off The device is in normal operating condition.


ALARM
Yellow An abnormal alarm is issued.

REMOTE Off This device is in local control.

8-2 PCS-9799 Station Manager

Date: 2015-03-31
8 Human Machine Interface

LED Display Description

Green This device can be controlled remotely.

The co-operating device is blocked or the communication between the two station
Off
CO-DEV OK managers is abnormal.

Green The two station managers are co-operating.

Off None synchronization signal is received.


SYNC
Green The device is successfully synchronized with the time source.

Note!

1. "HEALTHY" LED can only be litted on by energizing the device without any detection
of abnormality.

2. "ALARM" LED is litted on as long as a alarm exists. When all alarms disappear, it will
be turned off.

8.1.4 Front Debugging Port

There is a multiplex RJ45 port on the front panel. This port can be used as an RS-232 serial port
as well as a twisted-pair Ethernet port. As shown in the following figure, a customized cable is
applied for debugging via this multiplex RJ45 port.

P2

P1

P3

P1: To connect the multiplex RJ45 port. An 8-core cable is applied here.

P2: To connect the twisted-pair Ethernet port of the computer.

P3: To connect the RS-232 serial port of the computer.

The definition of the 8-core cable in the above figure is introduced in the following table.

Terminal Device side Computer side


Core color Function
No. (Left) (Right)
1 Orange & white TX+ of the Ethernet port P1-1 P2-1
2 Orange TX- of the Ethernet port P1-2 P2-2
3 Green & white RX+ of the Ethernet port P1-3 P2-3

PCS-9799 Station Manager 8-3

Date: 2015-03-31
8 Human Machine Interface

Terminal Device side Computer side


Core color Function
No. (Left) (Right)
4 Blue TXD of the RS-232 serial port P1-4 P3-2
5 Brown & white RXD of the RS-232 serial port P1-5 P3-3
6 Green RX- for the Ethernet port P1-6 P2-6
7 Blue & white P1-7
The ground connection of the RS-232 port. P3-5
8 Brown P1-8

8.1.5 Ethernet Port Setup

MON plug-in module is equipped with two or four 100Base-TX Ethernet interface. Take
NR4106MB as an example, its rear view and the definition of terminals are shown in the following
figure.

The Ethernet port can be used to communication with PC via auxiliary software (PCS-Explorer)
after connecting the device with PC, so as to fulfill on-line function (please refer to the instruction
manual of PCS-Explorer). At first, the connection between the device and PC must be established.
Through setting the IP address and subnet mask of corresponding Ethernet interface in the menu
"Settings -> Comm Settings -> IP", it should be ensured that the device and PC are in the same
network segment. For example, setting the IP address and subnet mask of network A. (using
network A to connect with PC)

PC: IP address is set as "198.87.96.102", subnet mask is set as "255.255.255.0"

The IP address and subnet mask of device should be [IP_LAN1] = 198.87.96.XXX, [Mask_LAN1]
=255.255.255.0, [En_LAN1] =1. (XXX can be any value from 0 to 255 except 102)

8.2 LCD Display

2014 -04- 11 09 : 40: 15 ID : 113 .1

Station Manager

MON1 MON2 MON3 MON4 COM1 COM6 COM11


1 7 X

2 X 8
3 F 9

4 10
5 11 5 10 15
6 12

This is the normal display of the LCD, each circle on the LCD represents the communication state
of each port. The "MON" represents the MON module where the 12 circles represent the 12

8-4 PCS-9799 Station Manager

Date: 2015-03-31
8 Human Machine Interface

Ethernet ports. The "COM" represents the COM module of which each has 5 serial or modem
ports.

The meaning of the circles:

●: This port is enabled and the communication is ok.

X : This port is enabled but the communication is abnormal.


F : This port is enabled, but the physical connection is abnormal.


○: This port is disabled.

8.3 Menu Tree

Note!

According to different applications in different engineering requirements, display of menu


in HMI may be different.

The descriptions about menu are based on the maximized configuration, for a specific
project, if some function is not available, the corresponding submenu will be hidden.

8.3.1 Main Menu

Press "▲" of any running interface and enter the main menu. Select different submenu by "▲"
and "▼". Enter the selected submenu by pressing "ENT" or "►". Press "◄" and return to the
previous menu. Press "ESC" back to main menu directly.

Device State
Database
Settings
Local Cmd
Extended Functions
Information
Test
Clock
Language

The menu of this device is organized into main menu and submenus, much like a PC directory
structure. The menu of this device is divided into several sections.

PCS-9799 Station Manager 8-5

Date: 2015-03-31
8 Human Machine Interface

8.3.2 Device State

Main Menu

Device State

Comm State

Net State

COM State

IED State

Clock Syn State

Dual Device State

Superv State

This menu is mainly used to display some real-time states, including communication state,
co-operated device state and self-supervision states.

No. Item Function description


To display the states of the communication with IEDs connected to this device.
Net State The communication states of the Ethernet ports.
1 Comm State
COM State The communication states of the serial ports and modem ports.
IED State The communication states of the connected IEDs.
2 Clock Syn State To display the state of the clock synchronization.
3 Dual Device State To display the state of the co-operated device.
4 Superv State To display the alarms of self-supervision.

8.3.3 Database

Main Menu

Database

Online

Records

SOE Records

Operation Logs

8-6 PCS-9799 Station Manager

Date: 2015-03-31
8 Human Machine Interface

This menu is mainly used to display the state of the real-time and historical data.

No. Item Function description

To display all the real-time data including the binary inputs, the measurements, the
1 Online
tap positions, the metering data, the settings, parameters and etc.

To display all the historical data, including SOE reports and operation reports.

2 Records SOE Records To display the SOE (sequence of event) reports.

Operation Logs To display the operation logs.

8.3.4 Settings

Main Menu

Settings

Comm Settings

IP

Route

MAC

ID Settings

This menu is used to configure the parameters of the device, which include the device address, ID,
IP address, MAC address, the route table etc.

No. Item Function description

To display and set and set the IP, MAC address and the route table.

IP To display and set IP address.


1 Comm Settings
Route To display and set the route table.

MAC To display MAC address.

2 ID Settings To display and set and set the device's identification in the network.

PCS-9799 Station Manager 8-7

Date: 2015-03-31
8 Human Machine Interface

8.3.5 Local Command

Main Menu

Local Cmd

Ping

Reset Process

Format Disk

Device Maintenance

This menu is used to do certain operation locally via HMI.

No. Item Function description

1 Ping To start an Ethernet ping test of the specified ranged addresses.

2 Reset Process To reset the progress of a selected application.

3 Format Disk To format the storage disk of this device.

4 Device Maintenance To indicate the maintenance state of the device in communication.

8.3.6 Information

This menu is mainly used to display the version of the firmware, the version of the configuration
and the time of downloading the configuration.

8.3.7 Test

Main Menu

Test

Auto Test

Net Test

COM Test

BI/BO Test

LED Test

LCD Test

This menu is used to self-test the device.

No. Item Function description

1 Auto Test To entirely start all the above tests automatically.

8-8 PCS-9799 Station Manager

Date: 2015-03-31
8 Human Machine Interface

No. Item Function description

2 Net Test To start the communication test of the Ethernet ports.

3 COM Test To start the communication test of the serial ports and modem ports.

4 BI/BO Test To start the contact test of the IO module.

5 LED Test To start the light test of the LED indicators.

6 LCD Test To start the pixel check of the LCD display.

8.3.8 Clock

This menu is mainly used to view and modify the current time of the internal clock in this device.

8.3.9 Language

This menu is used to set the LCD display language with "+" or "-".

PCS-9799 Station Manager 8-9

Date: 2015-03-31
8 Human Machine Interface

8-10 PCS-9799 Station Manager

Date: 2015-03-31
9 Configurable Function

9 Configurable Function

Table of Contents
9 Configurable Function ...................................................................... 9-a
9.1 Overview .......................................................................................................... 9-1
9.2 Function ........................................................................................................... 9-1
9.3 Application....................................................................................................... 9-1

PCS-9799 Station Manager 9-a

Date: 2015-03-31
9 Configurable Function

9-b PCS-9799 Station Manager


Date: 2015-03-31
9 Configurable Function

9.1 Overview

The PCS-COMM configuration and debugging tool is the auxiliary software designed for the PCS
series communication devices (including remote terminal unit, station manager, protocol converter,
and gateway) with offline configuration and online debugging functions.

The PCS series communication device is the new generation of communication device produced
by NR Electric on the research of integrated automation system and the site operation experience
over years. The PCS-COMM configuration and debugging tool works as the associated auxiliary
software is designed and developed on the basis of the object-oriented technology, the
network-based database technology, the cross-platform visual technology and the latest industrial
standards, which can fully support IEC60870-5-103, IEC61850 and other international standards
and to meet the configuration and debugging demands of communication device in traditional
substation, digitalized substation and power plant.

Note!

For the detailed function instruction and operating procedure of the auxiliary software,
please refer to "PCS-COMM Configuration and Debugging Tool Instruction Manual".

9.2 Function
The following functions are included:

 Configuration and management of IED in station: This tool can configure all the IEDs
connected to the PCS series communication device. And in the same time, user can view the
configurations of all the IED through this tool.

 Offline configuration function: The access and transfer rules of the PCS series communication
device can be configured to meet the site requirements

 Visual configuration of device: This graphical and symbolical tool is designed to facilitate the
configuration of the PCS series communication device, most of the operations can be
accomplished several clicks on the mouse.

 Online debugging function: This tool integrates the download and debugging functions. The
configured scheme can be downloaded to the corresponding PCS series communication
device, and the device status can be viewed and debugged online through the tool.

9.3 Application
The PCS-COMM configuration and debugging tool of the PCS series communication device is
applicable to:

 Power system

The integrated automation system of a new substation (traditional, digitalized, various voltage

PCS-9799 Station Manager 9-1

Date: 2015-03-31
9 Configurable Function

levels)

The renewal of integrated automation system of an existing substation (traditional, digitalized,

various voltage levels)

 Other systems

The monitoring system of wind power station and photovoltaic power plant.

9-2 PCS-9799 Station Manager


Date: 2015-03-31
10 Communication

10 Communication

Table of Contents
10 Communication ............................................................................. 10-a
10.1 Overview ...................................................................................................... 10-1
10.2 Rear Communication Port .......................................................................... 10-1
10.2.1 RS-485 Interface.............................................................................................................. 10-1

10.2.2 Ethernet Interface ............................................................................................................ 10-3

10.3 IEC60870-5-103 Interface over Serial Port ................................................ 10-4


10.3.1 Physical Connection and Link Layer ............................................................................... 10-4

10.3.2 Initialization ...................................................................................................................... 10-4

10.3.3 Time Synchronization ...................................................................................................... 10-5

10.3.4 Spontaneous Events ........................................................................................................ 10-5

10.3.5 General Interrogation ....................................................................................................... 10-5

10.3.6 General Service ............................................................................................................... 10-5

10.3.7 Disturbance Records ....................................................................................................... 10-5

10.4 Brief of IEC 61850 Protocol ........................................................................ 10-6


10.5 Brief of IEC 60870-5-101 Protocol .............................................................. 10-6
10.5.1 Features ........................................................................................................................... 10-7

10.5.2 Frame Format .................................................................................................................. 10-7

10.5.3 Types supported .............................................................................................................. 10-7

10.6 Brief of IEC 60870-5-104 Protocol .............................................................. 10-8

List of Figures
Figure 10.2-1 EIA RS-485 bus connection arrangements ..................................................... 10-2

Figure 10.2-2 Ethernet communication cable ........................................................................ 10-3

Figure 10.2-3 Ethernet communication structure .................................................................. 10-4

PCS-9799 Station Manager 10-a


Date: 2015-03-31
10 Communication

10-b PCS-9799 Station Manager


Date: 2015-03-31
10 Communication

10.1 Overview

This section outlines the remote communications interfaces of this device. This device supports
several protocols (server & client) via the rear communication interfaces. The standard protocols
provided by the device are instructed in this chapter.

The rear EIA RS-485 interface is isolated and is suitable for permanent connection of whichever
protocol is selected. The advantage of this type of connection is that up to 32 devices can be
"daisy chained" together using a simple twisted pair electrical connection.

It should be noted that the descriptions contained within this section do not aim to fully detail the
protocol itself. The relevant documentation for the protocol should be referred to for this
information. This section serves to describe the specific implementation of the protocol in the
device.

Note!

A special demand besides the standard protocols described in this chapter must be
declared obviously and clearly in the technic sheet and the contract. Please pay attention
and provide detailed protocol demand when ordering.

10.2 Rear Communication Port

10.2.1 RS-485 Interface


This device provides several rear RS-485 communication ports, and each port has three terminals
in the connector located on the back of the device and each port has a ground terminal for the
earth shield of the communication cable. The rear ports provide RS-485 serial data communication
and are intended for use with a permanently wired connection to a remote control center.

10.2.1.1 EIA RS-485 Standardized Bus

The EIA RS-485 two-wire connection provides a half-duplex fully isolated serial connection to the
product. The connection is polarized and whilst the product’s connection diagrams indicate the
polarization of the connection terminals it should be borne in mind that there is no agreed
definition of which terminal is which. If the master is unable to communicate with the product, and
the communication parameters match, then it is possible that the two-wire connection is reversed.

10.2.1.2 Bus Termination

The EIA RS-485 bus must have 120Ω (Ohm) ½ Watt terminating resistors fitted at either end
across the signal wires (refer to the following figure). Some devices may be able to provide the bus
terminating resistors by different connection or configuration arrangements, in which case
separate external components will not be required. However, this product does not provide such a
facility, so if it is located at the bus terminus then an external termination resistor will be required.

PCS-9799 Station Manager 10-1


Date: 2015-03-31
10 Communication

Master 120Ohm

120Ohm

Slave Slave Slave

Figure 10.2-1 EIA RS-485 bus connection arrangements

10.2.1.3 Bus Connections & Topologies

The EIA RS-485 standard requires that each device be directly connected to the physical cable
that is the communications bus. Stubs and tees are expressly forbidden, such as star topologies.
Loop bus topologies are not part of the EIA RS-485 standard and are forbidden by it.

Two-core screened cable is recommended. The specification of the cable will be dependent on the
application, although a multi-strand 0.5mm 2 per core is normally adequate. Total cable length must
not exceed 500m. The screen must be continuous and connected to ground at one end, normally
at the master connection point; it is important to avoid circulating currents, especially when the
cable runs between buildings, for both safety and noise reasons.

This product does not provide a signal ground connection. If a signal ground connection is present
in the bus cable then it must be ignored, although it must have continuity for the benefit of other
devices connected to the bus. At no stage must the signal ground be connected to the cables
screen or to the product’s chassis. This is for both safety and noise reasons.

10.2.1.4 Biasing

It may also be necessary to bias the signal wires to prevent jabber. Jabber occurs when the signal
level has an indeterminate state because the bus is not being actively driven. This can occur when
all the slaves are in receive mode and the master is slow to turn from receive mode to transmit
mode. This may be because the master purposefully waits in receive mode, or even in a high
impedance state, until it has something to transmit. Jabber causes the receiving device(s) to miss
the first bits of the first character in the packet, which results in the slave rejecting the message
and consequentially not responding. Symptoms of these are poor response times (due to retries),
increasing message error counters, erratic communications, and even a complete failure to
communicate.

Biasing requires that the signal lines be weakly pulled to a defined voltage level of about 1V. There
should only be one bias point on the bus, which is best situated at the master connection point.
The DC source used for the bias must be clean; otherwise, noise will be injected. Note that some
devices may (optionally) be able to provide the bus bias, in which case external components will
not be required.

10-2 PCS-9799 Station Manager


Date: 2015-03-31
10 Communication

Note!

It is extremely important that the 120Ω termination resistors be fitted. Failure to do so will
result in an excessive bias voltage that may damage the devices connected to the bus.

As the field voltage is much higher than that required, NR cannot assume responsibility for
any damage that may occur to a device connected to the network because of incorrect
application of this voltage.

Ensure that the field voltage is not being used for other purposes (i.e. powering logic inputs)
as this may cause noise to be passed to the communication network.

10.2.2 Ethernet Interface


This device can provide four rear Ethernet interfaces (optional) and they are unattached each
other. Parameters of each Ethernet port can be configured in the menu "Settings→Device
Setup→Comm Settings".

10.2.2.1 Ethernet Standardized Communication Cable

It is recommended to use twisted shielded eight-core cable as the communication cable. A picture
is shown below.

Figure 10.2-2 Ethernet communication cable

10.2.2.2 Connections and Topologies

Each equipment is connected with an exchanger via communication cable, and thereby it forms a
star structure network. Dual-network is recommended in order to increase reliability. SCADA is
connected to the exchanger and will play a role as master station, other equipment connected to
the exchanger will play a role as slave unit.

PCS-9799 Station Manager 10-3


Date: 2015-03-31
10 Communication

SCADA

Switch: Net A

Switch: Net B

……

Figure 10.2-3 Ethernet communication structure

10.3 IEC60870-5-103 Interface over Serial Port

The IEC60870-5-103 interface via serial port (RS-485) is a master/slave interface with the device
as the slave device. It is properly developed by NR.

The device conforms to compatibility level 3.

The following IEC60870-5-103 facilities are supported by this interface:

1. Initialization (reset)

2. Time synchronization

3. Event record extraction

4. General interrogation

5. General commands

6. Disturbance records

10.3.1 Physical Connection and Link Layer


Two EIA RS-485 standardized ports are available for IEC60870-5-103 in this device. The
transmission speed is optional: 4800 bit/s, 9600 bit/s, 19200 bit/s or 38400 bit/s.

The link layer strictly abides by the rules defined in the IEC60870-5-103.

10.3.2 Initialization
Whenever the device has been powered up, or if the communication parameters have been
changed, a reset command is required to initialize the communications. The device will respond to
either of the two reset commands (Reset CU or Reset FCB), the difference is that the Reset CU

10-4 PCS-9799 Station Manager


Date: 2015-03-31
10 Communication

will clear any unsent messages in the transmit buffer.

The device will respond to the reset command with an identification message ASDU 5, the COT
(Cause Of Transmission) of this response will be either Reset CU or Reset FCB depending on the
nature of the reset command.

10.3.3 Time Synchronization


The device time and date can be set using the time synchronization feature of the
IEC60870-5-103 protocol. The device will correct for the transmission delay as specified in
IEC60870-5-103. If the time synchronization message is sent as a send/confirm message then the
device will respond with a confirmation. Whether the time-synchronization message is sent as a
send confirmation or a broadcast (send/no reply) message, a time synchronization class 1 event
will be generated/produced.

If the device clock is synchronized using the IRIG-B input then it will not be possible to set the
device time using the IEC60870-5-103 interface. An attempt to set the time via the interface will
cause the device to create an event with the current date and time taken from the IRIG-B
synchronized internal clock.

10.3.4 Spontaneous Events


Events are categorized using the following information:

1. Type identification (TYP)

2. Function type (FUN)

3. Information number (INF)

Messages sent to substation automation system are grouped according to IEC60870-5-103


protocol. Operating elements are sent by ASDU2 (time-tagged message with relative time), and
status of binary signal and alarm element are sent by ASDU1 (time-tagged message). The cause
of transmission (COT) of these responses is 1.

10.3.5 General Interrogation


The GI can be used to read the status of the device, the function numbers, and information
numbers that will be returned during the GI cycle. The GI cycle strictly abides by the rules defined
in the IEC60870-5-103.

Refer the IEC60870-5-103 standard can get the enough details about general interrogation.

10.3.6 General Service


The generic functions can be used to read the setting and measurement of the device, and modify
the setting. Two supported type identifications are ASDU 21 and ASDU 10. For more details about
generic functions, see the IEC60870-5-103 standard.

10.3.7 Disturbance Records


This device can store up to eight disturbance records in its memory. A pickup of the fault detector
or an operation of the device can make the device store the disturbance records.

PCS-9799 Station Manager 10-5


Date: 2015-03-31
10 Communication

The disturbance records are stored in uncompressed format and can be extracted using the
standard mechanisms described in IEC60870-5-103.

10.4 Brief of IEC 61850 Protocol


The IEC 61850 standard is the result of years of work by electric utilities and vendors of electronic
equipment to produce standardized communications systems. IEC 61850 is a series of standards
describing client/server and peer-to-peer communications, substation design and configuration,
testing, environmental and project standards. The complete set includes:

1. IEC 61850-1: Introduction and overview

2. IEC 61850-2: Glossary

3. IEC 61850-3: General requirements

4. IEC 61850-4: System and project management

5. IEC 61850-5: Communications and requirements for functions and device models

6. IEC 61850-6: Configuration description language for communication in electrical substations


related to IEDs

7. IEC 61850-7-1: Basic communication structure for substation and feeder equipment–
Principles and models

8. IEC 61850-7-2: Basic communication structure for substation and feeder equipment - Abstract
communication service interface (ACSI)

9. IEC 61850-7-3: Basic communication structure for substation and feeder equipment–
Common data classes

10. IEC 61850-7-4: Basic communication structure for substation and feeder equipment–
Compatible logical node classes and data classes

11. IEC 61850-8-1: Specific Communication Service Mapping (SCSM) – Mappings to MMS (ISO
9506-1 and ISO 9506-2) and to ISO/IEC 8802-3

12. IEC 61850-9-1: Specific Communication Service Mapping (SCSM) – Sampled values over
serial unidirectional multidrop point to point link

13. IEC 61850-9-2: Specific Communication Service Mapping (SCSM) – Sampled values over
ISO/IEC 8802-3

14. IEC 61850-10: Conformance testing

These documents can be obtained from the IEC (http://www.iec.ch). It is strongly recommended
that all those involved with any IEC 61850 implementation obtain this document set.

10.5 Brief of IEC 60870-5-101 Protocol


IEC 60870-5-101 is a standard for power system monitoring, control & associated communications
for telecontrol, teleprotection, and associated telecommunications for electric power systems. This

10-6 PCS-9799 Station Manager


Date: 2015-03-31
10 Communication

is completely compatible with IEC 60870-5-1 to IEC 60870-5-5 standards and uses standard
asynchronous serial tele-control channel interface between DTE (Data Terminal Equipment) and
DCE (Data Circuit-terminating Equipment). The standard is suitable for multiple configurations like
point-to-point, star, mutidropped etc.

10.5.1 Features
 Supports unbalanced (only master initiated message) & balanced (can be master/slave
initiated) modes of data transfer.

 Link address and ASDU (Application Service Data Unit) addresses are provided for
classifying the end station and different segments under the same.

 Data is classified into different information objects and each information object is provided
with a specific address.

 Facility to classify the data into high priority (class-1) and low priority (class-2) and transfer the
same using separate mechanisms.

 Possibility of classifying the data into different groups (1-16) to get the data according to the
group by issuing specific group interrogation commands from the master & obtaining data
under all the groups by issuing a general interrogation.

 Cyclic & Spontaneous data updating schemes are provided.

 Facility for time synchronization

 Schemes for transfer of files-Example:IED's will store disturbance recorder file in the memory,
When electrical disturbance is occurred in the field. This file can be retrieved through IEC104
protocol for fault analysis

10.5.2 Frame Format


Character format of IEC 101 uses 1 start bit, 1 stop bit, 1 parity bit & 8 data bits. FT1.2 (defined in
IEC 60870-5-1) is used for frame format of IEC 101 which is suitable for asynchronous
communication with hamming distance of 4. This uses 3 types of frame formats - Frame with
variable length ASDU, Frame with fixed length & single character. Single character is used for
acknowledgments, fixed length frames are used for commands & variable lengths are used for
sending data.

10.5.3 Types supported


 Single indication without / with 24 / with 56 bit timestamps.

 Double indication without / with 24 / with 56 bit timestamps.

 Step position information without / with 24 / with 56 bit timestamps.

 Measured value – normalized, scaled, short floating point without / with timestamps.

 Bitstring of 32 bit without / with timestamps.

 Integrated totals (counters) without / with timestamps.

PCS-9799 Station Manager 10-7


Date: 2015-03-31
10 Communication

 Packed events (start & tripping ) of protection equipments

 Single commands

 Double commands

 Regulating step command

 Set point commands of various data formats

 Bitstring commands

 Interrogation commands

 Clock synchronization & delay acquisition commands

 Test & reset commands

10.6 Brief of IEC 60870-5-104 Protocol


IEC 60870-5-104 protocol is an extension of IEC101 protocol with the changes in transport,
network, link & physical layer services to suit the complete network access. The standard uses an
open TCP/IP interface to network to have connectivity to the LAN (Local Area Network) and
routers with different facility (ISDN, X.25, Frame relay etc.) can be used to connect to the WAN
(Wide Area Network). Application layer of IEC 104 is preserved same as that of IEC101 with some
of the data types and facilities not used. There are two separate link layers defined in the standard,
which is suitable for data transfer over Ethernet & serial line (P2P Point-to-Point Protocol). The
control field data of IEC104 contains various types of mechanisms for effective handling of
network data synchronization.

10-8 PCS-9799 Station Manager


Date: 2015-03-31
11 Installation

11 Installation

Table of Contents
11 Installation ...................................................................................... 11-a
11.1 Overview ........................................................................................................ 11-1
11.2 Safety Information ........................................................................................ 11-1
11.3 Check Shipment ............................................................................................ 11-2
11.4 Material and Tools Required ........................................................................ 11-2
11.5 Device Location and Ambient Conditions .................................................. 11-2
11.6 Mechanical Installation ................................................................................. 11-3
11.7 Electrical Installation and Wiring ................................................................. 11-4
11.7.1 Grounding Guidelines ........................................................................................................11-4

11.7.2 Cubicle Grounding .............................................................................................................11-4

11.7.3 Ground Connection on the Device ....................................................................................11-5

11.7.4 Grounding Strips and their Installation ..............................................................................11-6

11.7.5 Guidelines for Wiring .........................................................................................................11-6

List of Figures
Figure 11.6-1 Dimensions (full-width chassis, rear wiring, unit: mm) ................................. 11-3

Figure 11.6-5 Demonstration of module insertion ................................................................. 11-4

Figure 11.7-1 Cubicle grounding system ................................................................................ 11-5

Figure 11.7-2 Ground terminal of this device ......................................................................... 11-6

Figure 11.7-3 Ground strip and termination ........................................................................... 11-6

PCS-9799 Station Manager 11-a

Date: 2015-03-31
11 Installation

11-b PCS-9799 Station Manager

Date: 2015-03-31
11 Installation

11.1 Overview
The device must be shipped, stored and installed with the greatest care.

Choose the place of installation such that the communication interface and the controls on the
front of the device are easily accessible.

Air must circulate freely around the equipment. Observe all the requirements regarding place of
installation and ambient conditions given in this instruction manual.

Take care that the external wiring is properly brought into the equipment and terminated correctly
and pay special attention to grounding. Strictly observe the corresponding guidelines contained in
this section.

11.2 Safety Information


Modules and units may only be replaced by correspondingly trained personnel. Always observe
the basic precautions to avoid damage due to electrostatic discharge when handling the
equipment.

In certain cases, the settings have to be configured according to the demands of the engineering
configuration after replacement. It is therefore assumed that the personnel who replace modules
and units are familiar with the use of the operator program on the service PC.

DANGER!

Only insert or withdraw the PWR module while the power supply is switched off. To this
end, disconnect the power supply cable that connects with the PWR module.

WARNING!

Only insert or withdraw other modules while the power supply is switched off.

WARNING!

The modules may only be inserted in the slots designated in Section 6.2. Components
can be damaged or destroyed by inserting boards in the wrong slots.

DANGER!

Improper handling of the equipment can cause damage or an incorrect response of the
equipment itself or the primary plant.

WARNING!

Industry packs and ribbon cables may only be replaced or the positions of jumpers be
changed on a workbench appropriately designed for working on electronic equipment.

PCS-9799 Station Manager 11-1

Date: 2015-03-31
11 Installation

The modules, bus backplanes are sensitive to electrostatic discharge when not in the
unit's housing.

The basic precautions to guard against electrostatic discharge are as follows:

1. Should boards have to be removed from this device installed in a grounded cubicle in an HV
switchgear installation, please discharge yourself by touching station ground (the cubicle)
beforehand.

2. Only hold electronic boards at the edges, taking care not to touch the components.

3. Only works on the board which has been removed from the cubicle on a workbench designed
for electronic equipment and wear a grounded wristband. Do not wear a grounded wristband,
however, while inserting or withdrawing units.

4. Always store and ship the electronic boards in their original packing. Place electronic parts in
electrostatic screened packing materials.

11.3 Check Shipment


Check that the consignment is complete immediately upon receipt. Notify the nearest NR
Company or agent, should departures from the delivery note, the shipping papers or the order be
found.

Visually inspect all the material when unpacking it. When there is evidence of transport damage,
lodge a claim immediately in writing with the last carrier and notify the nearest NR Company or
agent.

If the equipment is not going to be installed immediately, store all the parts in their original packing
in a clean dry place at a moderate temperature. The humidity at a maximum temperature and the
permissible storage temperature range in dry air are listed in Chapter “Technical Data”.

11.4 Material and Tools Required


The necessary mounting kits will be provided, including screws, pincers and assembly
instructions.

A suitable drill and spanners are required to secure the cubicles to the floor using the plugs
provided (if this device is mounted in cubicles).

11.5 Device Location and Ambient Conditions


The place of installation should permit easy access especially to front of the device, i.e. to the
human machine interface of the equipment.

There should also be free access at the rear of the equipment for additions and replacement of
electronic boards.

Since every piece of technical equipment can be damaged or destroyed by inadmissible ambient
conditions, such as:

11-2 PCS-9799 Station Manager

Date: 2015-03-31
11 Installation

1. The location should not be exposed to excessive air pollution (dust, aggressive substances).

2. Surge voltages of high amplitude and short rise time, extreme changes of temperature, high
levels of humidity, severe vibration and strong induced magnetic fields should be avoided as
far as possible.

3. Air must not be allowed to circulate freely around the equipment.

The equipment can in principle be mounted in any attitude, but it is normally mounted vertically
(visibility of markings).

WARNING!

Excessively high temperature can appreciably reduce the operating life of this device.

11.6 Mechanical Installation


This device is made of single layer 4U chassis. The following figures show the dimensions and
cut-out size in the cubicle for reference in mounting.

482.6 (290)
465

Front Side
101.6

177

465±0.2
+0.4
451 -0

4-Ø6.8
101.6±0.1

+0.4

Cut-Out
179 -0

Figure 11.6-1 Dimensions (full-width chassis, rear wiring, unit: mm)

Note!

It is necessary to leave enough space top and bottom of the cut-out in the cubicle for heat
emission of this device.

The following figure shows the installation way of a module being plugged into a corresponding
slot.

PCS-9799 Station Manager 11-3

Date: 2015-03-31
11 Installation

Figure 11.6-2 Demonstration of module insertion

In the case of equipment supplied in cubicles, place the cubicles on the foundations that have
been prepared. Take care while doing so not to jam or otherwise damage any of the cables that
have already been installed. Secure the cubicles to the foundations.

11.7 Electrical Installation and Wiring


11.7.1 Grounding Guidelines
Switching operations in HV installations generate transient over voltages on control signal cables.
There is also a background of electromagnetic RF fields in electrical installations that can induce
spurious currents in the devices themselves or the leads connected to them.

All these influences can influence the operation of electronic apparatus.

On the other hand, electronic apparatus can transmit interference that can disrupt the operation of
other apparatus.

In order to minimize these influences as far as possible, certain standards have to be observed
with respect to grounding, wiring and screening.

Note!

All these precautions can only be effective if the station ground is of good quality.

11.7.2 Cubicle Grounding


The cubicle must be designed and fitted out such that the impedance for RF interference of the
ground path from the electronic device to the cubicle ground terminal is as low as possible.

Metal accessories such as side plates, blanking plates etc., must be effectively connected
surface-to-surface to the grounded frame to ensure a low-impedance path to ground for RF
interference. The contact surfaces must not only conduct well, they must also be non-corroding.

Note!

If the above conditions are not fulfilled, there is a possibility of the cubicle or parts of it
forming a resonant circuit at certain frequencies that would amplify the transmission of

11-4 PCS-9799 Station Manager

Date: 2015-03-31
11 Installation

interference by the devices installed and also reduce their immunity to induced
interference.

Movable parts of the cubicle such as doors (front and back) or hinged equipment frames must be
effectively grounded to the frame by three braided copper strips (see Figure 11.7-1).

The metal parts of the cubicle housing and the ground rail are interconnected electrically
conducting and corrosion proof. The contact surfaces shall be as large as possible.

Note!

For metallic connections please observe the voltage difference of both materials
according to the electrochemical code.

The cubicle ground rail must be effectively connected to the station ground rail by a grounding strip
(braided copper).

Door or hinged
equipment frame

Cubicle ground
rail close to floor

Braided
copper strip
Station
ground

Conducting
connection

Figure 11.7-1 Cubicle grounding system

11.7.3 Ground Connection on the Device


There is a ground terminal on the rear panel, and the ground braided copper strip can be
connected with it. Take care that the grounding strip is always as short as possible. The main thing
is that the device is only grounded at one point. Grounding loops from unit to unit are not allowed.

There are some ground terminals on some connectors of this device, and the sign is “GND”. All the
ground terminals are connected in the cabinet of this device. Therefore, the ground terminal on the
rear panel (see Figure 11.7-2) is the only ground terminal of this device.

PCS-9799 Station Manager 11-5

Date: 2015-03-31
11 Installation

Figure 11.7-2 Ground terminal of this device

11.7.4 Grounding Strips and their Installation


High frequency currents are produced by interference in the ground connections and because of
skin effect at these frequencies, only the surface region of the grounding strips is of consequence.

The grounding strips must therefore be of (preferably tinned) braided copper and not round copper
conductors, as the cross-section of round copper would have to be too large.

Proper terminations must be fitted to both ends (press/pinch fit and tinned) with a hole for bolting
them firmly to the items to be connected.

The surfaces to which the grounding strips are bolted must be electrically conducting and
non-corroding.

The following figure shows the ground strip and termination.

Press/pinch fit
cable terminal

Braided
copper strip Terminal bolt

Contact surface

Figure 11.7-3 Ground strip and termination

11.7.5 Guidelines for Wiring


There are several types of cables that are used in the connection of this device: braided copper
cable, serial communication cable etc. Recommendation of each cable:

1. Grounding: braided copper cable, 2.5mm 2 ~ 6.0mm 2

2. Power supply, binary inputs & outputs: brained copper cable, 1.0mm 2 ~ 2.5mm 2

3. AC voltage inputs: brained copper cable, 1.0mm 2 ~ 2.5mm 2

4. AC current inputs: brained copper cable, 1.5mm2 ~ 4.0mm 2

5. Serial communication: 4-core shielded braided cable

6. Ethernet communication: 4-pair shielded twisted category 5E cable

11-6 PCS-9799 Station Manager

Date: 2015-03-31
12 Commissioning

12 Commissioning

Table of Contents
12 Commissioning ............................................................................. 12-a
12.1 Overview ....................................................................................................... 12-1
12.2 Safety Instruction ......................................................................................... 12-1
12.3 Commission Tool ......................................................................................... 12-2
12.4 Setting Familiarization ................................................................................. 12-2
12.5 Product Check .............................................................................................. 12-3
12.5.1 With the Device De-energized .......................................................................................... 12-3

12.5.2 With the Device Energized ............................................................................................... 12-5

12.5.3 On-load Check .................................................................................................................. 12-8

12.6 Final Check ................................................................................................... 12-8

PCS-9799 Station Manager 12-a

Date: 2015-03-31
12 Commissioning

12-b PCS-9799 Station Manager

Date: 2015-03-31
12 Commissioning

12.1 Overview
This device is numerical in their design, implementing all functions in software. The device
employs a high degree self-checking so in the unlikely event of a failure, it will give an alarm.

Blank commissioning test and setting records are provided at the end of this manual for
completion as required.

Before carrying out any work on the equipment, the user should be familiar with the contents of
the safety and technical data sections and the ratings on the equipment’s rating label.

12.2 Safety Instruction

WARNING!

Hazardous voltages are present in this electrical equipment during operation.


Non-observance of the safety rules can result in severe personal injury or property
damage.

WARNING!

Only the qualified personnel shall work on and around this equipment after becoming
thoroughly familiar with all warnings and safety notices of this manual as well as with the
applicable safety regulations.

Particular attention must be drawn to the following:

1. The earthing screw of the device must be connected solidly to the protective earth conductor
before any other electrical connection is made.

2. Hazardous voltages can be present on all circuits and components connected to the supply
voltage or to the measuring and test quantities.

3. Hazardous voltages can be present in the device even after disconnection of the supply
voltage (storage capacitors!)

4. The limit values stated in the Chapter "Technical Data” must not be exceeded at all, not even
during testing and commissioning.

5. When testing the device with secondary test equipment, make sure that no other
measurement quantities are connected. Take also into consideration that the trip circuits and
may be close commands to the circuit breakers and other primary switches are disconnected
from the device unless expressly stated.

DANGER!

Current transformer secondary circuits must have been short-circuited before the current
leads to the device are disconnected.

PCS-9799 Station Manager 12-1

Date: 2015-03-31
12 Commissioning

WARNING!

Primary test may only be carried out by qualified personnel, who are familiar with the
commissioning of the system, the operation of the plant and safety rules and regulations
(switching, earthing, etc.).

12.3 Commission Tool


Minimum equipment required:

1. Multifunctional dynamic current and voltage injection test set with interval timer.

2. Multimeter with suitable AC current range and AC/DC voltage ranges of 0~440V and 0~250V
respectively.

3. Continuity tester (if not included in the multimeter).

Note!

Modern test set may contain many of the above features in one unit.

Optional equipment:

1. An electronic or brushless insulation tester with a DC output not exceeding 500V (for
insulation resistance test when required).

2. A portable PC, with appropriate software (this enables the rear communications port to be
tested, if this is to be used, and will also save considerable time during commissioning).

3. EIA RS-485 to EIA RS-232 converter (if EIA RS-485 IEC60870-5-103 port is being tested).

4. Tester: HELP-9000.

12.4 Setting Familiarization


When commissioning this device for the first time, sufficient time should be allowed to become
familiar with the method by which the settings are applied. A detailed description of the menu
structure of this device is contained in Chapter "Operation Theory” and Chapter "Settings”.

With the front cover in place all keys are accessible. All menu cells can be read. The LED
indicators and alarms can be reset. Protection or configuration settings can be changed, or fault
and event records cleared. However, menu cells will require the appropriate password to be
entered before changes can be made.

Alternatively, if a portable PC is available together with suitable setting software (such as


PCS-9700 HMI software), the menu can be viewed one page at a time to display a full column of
data and text. This PC software also allows settings to be entered more easily, saved to a file on
disk for future reference or printed to produce a setting record. Refer to the PC software user
manual for details. If the software is being used for the first time, allow sufficient time to become
familiar with its operation.

12-2 PCS-9799 Station Manager

Date: 2015-03-31
12 Commissioning

12.5 Product Check


These product checks cover all aspects of the device which should be checked to ensure that it
has not been physically damaged prior to commissioning, is functioning correctly and all input
quantity measurements are within the stated tolerances.

If the application-specific settings have been applied to the device prior to commissioning, it is
advisable to make a copy of the settings so as to allow them restoration later. This could be done
by extracting the settings from the device itself via printer or manually creating a setting record.

12.5.1 With the Device De-energized

This device is fully numerical and the hardware is continuously monitored. Commissioning tests
can be kept to a minimum and need only include hardware tests and conjunctive tests. The
function tests are carried out according to user’s correlative regulations.

The following tests are necessary to ensure the normal operation of the equipment before it is first
put into service.

1. Hardware tests

These tests are performed for the following hardware to ensure that there is no hardware
defect. Defects of hardware circuits other than the following can be detected by
self-monitoring when the DC power is supplied.

2. User interfaces test

3. Binary input circuits and output circuits test

4. AC input circuits test

5. Function tests

These tests are performed for the following functions that are fully software-based.

1. Measuring elements test

2. Timers test

3. Conjunctive tests

The tests are performed after the device is connected with the primary equipment and other
external equipment.

1. On load test.

2. Phase sequence check and polarity check.

12.5.1.1 Visual Inspection

After unpacking the product, check for any damage to the device case. If there is any damage, the
internal module might also have been affected, contact the vendor. The following items listed are
necessary.

1. Device panel

PCS-9799 Station Manager 12-3

Date: 2015-03-31
12 Commissioning

Carefully examine the device panel, device inside and other parts inside to see that no
physical damage has occurred since installation.

2. Panel wiring

Check the conducting wire which is used in the panel to assure that their cross section
meeting the requirement.

Carefully examine the wiring to see that they are no connection failure exists.

3. Device plug-in modules

Check each plug-in module of the equipment on the panel to make sure that they are well
installed into the equipment without any screw loosened.

4. Earthing cable

Check whether the earthing cable from the panel terminal block is safely screwed to the panel
steel sheet.

5. Switch, keypad, isolator binary inputs and push button

Check whether all the switches, equipment keypad, isolator binary inputs and push buttons
work normally and smoothly.

12.5.1.2 Insulation Test (if required)

Insulation resistance tests are only necessary during commissioning if it is required for them to be
done and they have not been performed during installation.

Isolate all wiring from the earth and test the isolation with an electronic or brushless insulation
tester at a DC voltage not exceeding 500V, The circuits need to be tested should include:

1. Voltage transformer circuits

2. Current transformer circuits

3. DC power supply

4. Optic-isolated control inputs

5. Output contacts

6. Communication ports

The insulation resistance should be greater than 100MΩ at 500V.

Test method:

To unplug all the terminals sockets of this device, and do the Insulation resistance test for each
circuit above with an electronic or brushless insulation tester.

On completion of the insulation resistance tests, ensure all external wiring is correctly
reconnected to the device.

12-4 PCS-9799 Station Manager

Date: 2015-03-31
12 Commissioning

12.5.1.3 External Wiring

Check that the external wiring is correct to the relevant device diagram and scheme diagram.
Ensure as far as practical that phasing/phase rotation appears to be as expected.

Check the wiring against the schematic diagram for the installation to ensure compliance with the
customer’s normal practice.

12.5.1.4 Auxiliary Power Supply

The device only can be operated under the auxiliary power supply depending on the device’s
nominal power supply rating.

The incoming voltage must be within the operating range specified in Chapter "Technical Data”,
before energizing the device, measure the auxiliary supply to ensure it within the operating range.

Other requirements to the auxiliary power supply are specified in Chapter "Technical Data”. See
this section for further details about the parameters of the power supply.

WARNING!

Energize this device only if the power supply is within the specified operating ranges in
Chapter "Technical Data”.

12.5.2 With the Device Energized


The following groups of checks verify that the device hardware and software is functioning
correctly and should be carried out with the auxiliary supply applied to the device.

The current and voltage transformer connections must remain isolated from the device for these
checks. The trip circuit should also remain isolated to prevent accidental operation of the
associated circuit breaker.

12.5.2.1 Front Panel LCD Display

Connect the device to DC power supply correctly and turn the device on. Check program version
and forming time displayed in command menu to ensure that are corresponding to what ordered.

12.5.2.2 Date and Time

If the time and date is not being maintained by substation automation system, the date and time
should be set manually.

Set the date and time to the correct local time and date using menu item "Clock”.

In the event of the auxiliary supply failing, with a battery fitted on CPU board, the time and date
will be maintained. Therefore when the auxiliary supply is restored the time and date will be
correct and not need to set again.

To test this, remove the auxiliary supply from the device for approximately 30s. After being
re-energized, the time and date should be correct.

PCS-9799 Station Manager 12-5

Date: 2015-03-31
12 Commissioning

12.5.2.3 Light Emitting Diode (LED)

On power up, the green LED "HEALTHY” should have illuminated and stayed on indicating that
the device is healthy.

The device has latched signal devices which remember the state of the trip, auto-reclose when
the device was last energized from an auxiliary supply. Therefore these indicators may also
illuminate when the auxiliary supply is applied. If any of these LEDs are on then they should be
reset before proceeding with further testing. If the LED successfully reset, the LED goes out.
There is no testing required for that that LED because it is known to be operational.

It is likely that alarms related to voltage transformer supervision will not reset at this stage.

12.5.2.4 LED Test

1. Apply the rated DC power supply and check that the "HEALTHY” LED is lighting in green. We
need to emphasize that the "HEALTHY” LED is always lighting in operation course except that
the equipment find serious errors in it.

2. Produce one of the abnormal conditions listed in Chapter "Supervision”, the "ALARM” LED
will light in yellow. When abnormal condition reset, the "ALARM” LED extinguishes.

3. Switch the remote/local control mode of the device to verify it will not transmit any remote
control command if the "REMOTE" LED is off.

4. The "CO-DEV OK" LED is lighting in green if the dual-device mode is applied. Switch of the
other device to check if the LED is off.

5. The "SYNC" LED is lighting in green if a time synchronization source is connected to the
device and the signal is normal. The LED will be of if there is no signal or the signal is
anormal.

12.5.2.5 Binary status change test

This test verifies the correctness and the trasmission response time of remote signalisation of
binary status' change.

Steps of test:

1. Select the device to test.

2. According to the terminal arrangement of the device, produce certain change of binary status
(0->1 or 1->0).

3. Register the data and compare it to the display of SCADA and gateway.

4. Verify the response time of SCADA and gateway.

Note!

The binary inputs should be energized one at a time, see external connection diagrams
for terminal numbers.

12-6 PCS-9799 Station Manager

Date: 2015-03-31
12 Commissioning

Ensure that the voltage applied on the binary input must be within its operating range.

Cabinet name Cabinet No. Contact No. Device type Device address

SCADA Gateway
No. Real status Device display
Display response time Display response time

……

12.5.2.6 Remote control test

This test verifies the sequence and correctness of remote control.

Steps of test:

1. Select the the primary switchgear to control.

2. Send a remote control command from Dispatching Centre or SCADA or local control device.

3. Verify the result of remote control.

4. Verify the response time of SCADA and gateway in using a multimeter on the output contact.

Note!

See the external connection diagram for the position of output contact.

No. Device type Device address Control object Open Close Response time

……

12.5.2.7 SOE record test

This test verifies the correctness and response time of SOE record.

Steps of test:

1. Select the three devices to test.

2. For each device, connect 10 binary inputs in parallel and produce a change of status together

3. Verify and compare the recording time of SCADA and the local device.

Cabinet name Cabinet No. Contact No. Device type Device address

PCS-9799 Station Manager 12-7

Date: 2015-03-31
12 Commissioning

SOE recording time


No. Real status
Device SCADA

……

12.5.3 On-load Check

The objectives of the on-load checks are:

1. Confirm the external wiring to the current and voltage inputs is correct.

2. Measure the magnitude of on-load current and voltage (if applicable).

3. Check the polarity of each current transformer.

However, these checks can only be carried out if there are no restrictions preventing the
tenderization of the plant being protected.

Remove all test leads, temporary shorting leads, etc. and replace any external wiring that has
been removed to allow testing.

If it has been necessary to disconnect any of the external wiring from the device in order to
perform any of the foregoing tests, it should be ensured that all connections are replaced in
accordance with the relevant external connection or scheme diagram. Confirm current and
voltage transformer wiring.

12.6 Final Check


After the above tests are completed, remove all test or temporary shorting leads, etc. If it has been
necessary to disconnect any of the external wiring from the device in order to perform the wiring
verification tests, it should be ensured that all connections are replaced in accordance with the
relevant external connection or scheme diagram.

Ensure that the device has been restored to service.

If the device is in a new installation or the circuit breaker has just been maintained, the circuit
breaker maintenance and current counters should be zero. If a test block is installed, remove the
test plug and replace the cover so that the device is put into service.

Ensure that all event records, fault records and alarms have been cleared and LED’s has been
reset before leaving the device.

12-8 PCS-9799 Station Manager

Date: 2015-03-31
13 Maintenance

13 Maintenance

Table of Contents
13 Maintenance ................................................................................... 13-1
13.1 Appearance Check ....................................................................................... 13-1
13.2 Failure Tracing and Repair .......................................................................... 13-1
13.3 Module Replacement ................................................................................... 13-1
13.4 Cleaning ........................................................................................................ 13-3
13.5 Storage .......................................................................................................... 13-3

PCS-9799 Station Manager 13-1

Date: 2015-03-31
13 Maintenance

13-2 PCS-9799 Station Manager

Date: 2015-03-31
13 Maintenance

This device is designed to require no special maintenance. All measurement and signal
processing circuit are fully solid state. All input modules are also fully solid state. The output relays
are hermetically sealed.

Since the device is almost completely self-monitored, from the measuring inputs to the output
relays, hardware and software defects are automatically detected and reported. The
self-monitoring ensures the high availability of the device and generally allows for a corrective
rather than preventive maintenance strategy. Therefore, maintenance checks in short intervals
are not required.

Operation of the device is automatically blocked when a hardware failure is detected. If a problem
is detected in the external measuring circuits, the device normally only provides alarm messages.

13.1 Appearance Check


1. The device case should be clean without any dust stratification. Case cover should be sealed
well. No component has any mechanical damage and distortion, and they should be firmly
fixed in the case. Device terminals should be in good condition. The keys on the front panel
with very good feeling can be operated flexibly.

2. It is only allowed to plug or withdraw device board when the supply is reliably switched off.
Never allow the CT secondary circuit connected to this equipment to be opened while the
primary system is live when withdrawing an AC module. Never try to insert or withdraw the
device board when it is unnecessary.

3. Check weld spots on PCB whether they are well soldered without any rosin joint. All dual
inline components must be well plugged.

13.2 Failure Tracing and Repair


Failures will be detected by automatic supervision or regular testing.

When a failure is detected by supervision, a remote alarm is issued and the failure is indicated on
the front panel with LED indicators and LCD display. It is also recorded in the event record.
Failures detected by supervision are traced by checking the “Superv State” screen on the LCD.

When a failure is detected during regular testing, confirm the following:

1. Test circuit connections are correct

2. Modules are securely inserted in position

3. Correct DC power voltage is applied

4. Correct AC inputs are applied

5. Test procedures comply with those stated in the manual

13.3 Module Replacement


If the failure is identified to be in the device module and the user has spare modules, the user can

PCS-9799 Station Manager 13-1

Date: 2015-03-31
13 Maintenance

recover the device by replacing the failed modules.

Repair at the site should be limited to module replacement. Maintenance at the component level
is not recommended.

Check that the replacement module has an identical module name (AI, PWR, MON, BI, BO, etc.)
and hardware type-form as the removed module. Furthermore, the MON module replaced should
have the same software version. In addition, the AI and PWR module replaced should have the
same ratings.

The module name is indicated on the top front of the module. The software version is indicated in
LCD menu “Information”->“Version Info”.

Caution!

When handling a module, take anti-static measures such as wearing an earthed wristband
and placing modules on an earthed conductive mat. Otherwise, many of the electronic
components could suffer damage.

1. Replacing a module

1) Switch off the DC power supply

2) Disconnect the trip outputs

3) Short circuit all AC current inputs and disconnect all AC voltage inputs

4) Unscrew the module connector

5) Unplug the connector from the target module.

6) Unscrew the module.

7) Pull out the module

8) Inset the replacement module in the reverser procedure.

9) After replacing the MON module, input the application-specific setting values again.

Warning!

Hazardous voltage can be present in the DC circuit just after switching off the DC power
supply. It takes approximately 30 seconds for the voltage to discharge.

2. Replacing the Human Machine Interface Module (front panel)

1) Open the device front panel

2) Unplug the ribbon cable on the front panel by pushing the catch outside.

3) Detach the HMI module from the device

4) Attach the replacement module in the reverse procedure.

13-2 PCS-9799 Station Manager

Date: 2015-03-31
13 Maintenance

Warning!

Units and modules may only be replaced while the supply is switched off and only by
appropriately trained and qualified personnel. Strictly observe the basic precautions to
guard against electrostatic discharge.

Warning!

When handling a module, take anti-static measures such as wearing an earthed wristband
and placing modules on an earthed conductive mat. Otherwise, many of the electronic
components could suffer damage. After replacing the MON module, check the settings.

Danger!

After replacing modules, be sure to check that the same configuration is set as before the
replacement. If this is not the case, there is a danger of the unintended operation of
switchgear taking place or of devices not functioning correctly. Persons may also be put in
danger.

13.4 Cleaning
Before cleaning the device, ensure that all AC/DC supplies, current transformer connections are
isolated to prevent any chance of an electric shock whilst cleaning. Use a smooth cloth to clean
the front panel. Do not use abrasive material or detergent chemicals.

13.5 Storage
The spare device or module should be stored in a dry and clean room. Based on IEC standard
60255-1 the storage temperature should be from -40°C to +70°C, but the temperature of from 0°C
to +40°C is recommended for long-term storage.

PCS-9799 Station Manager 13-3

Date: 2015-03-31
13 Maintenance

13-4 PCS-9799 Station Manager

Date: 2015-03-31
14 Decommissioning and Disposal

14 Decommissioning and Disposal

Table of Contents
14 Decommissioning and Disposal .................................................. 14-a
14.1 Decommissioning ........................................................................................ 14-1
14.2 Disposal........................................................................................................ 14-1

PCS-9799 Station Manager 14-a

Date: 2015-03-31
14 Decommissioning and Disposal

14-b PCS-9799 Station Manager

Date: 2015-03-31
14 Decommissioning and Disposal

14.1 Decommissioning
1. Switching off

To switch off this device, switch off the external miniature circuit breaker of the power supply.

2. Disconnecting Cables

Disconnect the cables in accordance with the rules and recommendations made by relational
department.

Danger!

Before disconnecting the power supply cables that connected with the PWR module of this
device, make sure that the external miniature circuit breaker of the power supply is
switched off.

Danger!

Before disconnecting the cables that are used to connect analog input module with the
primary CTs and VTs, make sure that the circuit breaker for the primary CTs and VTs is
switched off.

3. Dismantling

The device rack may now be removed from the system cubicle, after which the cubicles may
also be removed.

Danger!

When the station is in operation, make sure that there is an adequate safety distance to
live parts, especially as dismantling is often performed by unskilled personnel.

14.2 Disposal
In every country there are companies specialized in the proper disposal of electronic waste.

Note!

Strictly observe all local and national regulations when disposing of the device.

PCS-9799 Station Manager 14-1

Date: 2015-03-31
14 Decommissioning and Disposal

14-2 PCS-9799 Station Manager

Date: 2015-03-31
15 Manual Version History

15 Manual Version History


In the latest version of the instruction manual, several descriptions on existing features have been
modified.

Manual version and modification history records

Manual Version Software


Date Description of change
Source New Version
R1.00 R1.00 2015-03-31 Form the original manual.

PCS-9799 Station Manager 15-1

Date: 2015-03-31
15 Manual Version History

15-2 PCS-9799 Station Manager

Date: 2015-03-31

You might also like