WASHING MACHINE

SW70A1(P)/XSE
SW70B1(P)/XSE

WASHING MACHINE CONTENTS

1. Precautions

2. Specifications

3. Features

4. Operating Instructions

5. Schematic and Wiring Diagrams

6. Disassembly and Reassembly

7. Troubleshooting

8. Exploded Views
CONTENTS
1. Precautions
1-1 Safety Precautions 1-1
1-1-1. Use Genuine Parts 1-1
1-1-2. Grounding 1-1
1-2 Servicing Precautions 1-1
1-2-1. Observe Warnings 1-1
1-2-2. Special Precautions for Parts Assembly and Wiring 1-1
1-2-3. Safety Checks after Servicing 1-1
1-2-4. Insulation Check 1-1

2. Specifications 2-1

3. Features
3-1 Dimensions 3-1
3-2 Installation 3-1
3-2-1. Level Specifications and Wall-Clearance Distances 3-1
3-2-2. Balance 3-1
3-2-3. Controlling the Front Adjustable Leg 3-1
3-2-4. Connecting the Drain Hose 3-1
3-2-5. Connecting the water supply hose 3-2
3-2-6. Positioning the Drain hose 3-2

4. Operating Instructions
4-1 Component Identification 4-1
4-2 Control Panel 4-2
4-3 Function Descriptions 4-3
4-3-1. Water Supply 4-3
4-3-2. Water level 4-3
4-3-3. Course 4-3
4-3-4. Function Button 4-3
4-3-5. Delay Time 4-3
4-3-6. Start/Hold 4-3
4-3-7. Power 4-3
4-4 Description of Technical Points 4-4
4-4-1. Weight Recognizing Function 4-4
4-4-2. Water Supplying Function 4-4
4-4-3. Soak Function 4-4
4-4-4. Fuzzy Function 4-4
4-5 Program Chart 4-5

SAMSUNG ELECTRONICS CO., LTD

5. Schematic and Wiring Diagrams

5-1 Wiring Diagram 5-1

5-2 PCB and Pattern Diagram 5-2

6. Disassembly and Reassembly

6-1 Cautions for Disassembly and Reassembly 6-1

6-1-1. Before Servicing 6-1

6-1-2. During Servicing 6-1

6-1-2. After Servicing 6-1

6-2 Disassembly 6-2

6-3 Spin-Nut Repairing Box 6-4

6-3-1. Procedure 6-4

7. Troubleshooting

7-1 Self-diagnostic Functions (Buzzer Alarm) 7-1

7-2 Test Mode 7-2

7-3 Servicing Precautions 7-3

7-4 Troubleshooting 7-4

7-4-1. Troubleshooting of the Power Supply Board 7-4

7-4-2. Keyboard 7-4

7-4-3. Driving Unit 7-5

7-4-4. Inspection After Repair 7-11

8. Exploded Views 8-1

WASHING MACHINE
 Copyright
©Samsung Electronics Co., LTD.
All right reserved.
The information in this manual is subject to change without notice.

1. Precautions
When performing trouble - shooting and part replacement during servicing note the following safety precautions.

1-1 Safety Precautions

1-1-1 Use Genuine Parts 1-1-2 Grounding
The components of the washing machine have safety - Connect the grounding wire to the shell plate, and bury
features such as non - combustibility and voltage it under at least 25cm of earth ; alternatively, connect
withstanding. Therefore, always use the same part as the ground wire to the appropriate pin on a properly
used when replacing parts. In particular, be sure to use grounded power receptacle.
only designated parts in case of major safety parts ¥Never ground it to the telephone line, lightning rod,
identified by the making. or gas pipe.

1-2 Servicing Precautions

1-2-1 Observe warnings 1-2-4 Insulation Check

Be sure to follow special warnings and precautions that Pull out the plug from the power receptacle, pour water
are described on part labels and in the owner's manual. into the spin tub, and then set the timer. Check to see
that the insulation resistance between the terminals of
1-2-2 Special Precautions for Parts Assembly the plug and the exposed metal is greater, than 1 M½.
and wiring
Note : When it is impossible to perform the insulation
When assembling parts that use safety - insulation check with a 500V insulation resistance tester,
material (such as tube and tape), or when installing use other testers for inspection.
internal wiring, be sure to restore all parts and wiring to
their original positions.
Take special care to avoid contact with sharp edges.

1-2-3 Safety Checks after Servicing

After servicing, check to see that the screws, parts, and
wiring are restored to their original positions, and
check the insulation between the external metals and
the socket plug. In addition, place the washing machine
in a level position (less than 1û of grade) to prevent
vibration and noise during operations.

SAMSUNG ELECTRONICS CO., LTD 1-1

2. Specifications

Classifications Specifications

Washing and Dehydrating Capacity SW70A1(P) SW70B1(P) SW75A1S(P) SW75B1S(P)

5.0 kg 5.5 kg
Washing Method Heavy duty rotation type (centripetal current)
Standard Volume of Water High Level 50 ı
Medium Level 43 ı
Low Level 35 ı
Extra low level 28 ı
Applicable Volume of Water 145 ı (high level of water)
Rotation of the Pulsator 126 rpm
Rotation of the Spin Tub 760 rpm
Power Consumption Washing 310 W
Spinning 240 W
Dehydration Method Centrifugal dehydration type
Drain Control Motor driven
Applicable Water Pressure 0.05~0.78Mpa (0.5 kgf / cm2 ~ 8.0 kgf / cm2)
Weight Gross 34kg
Net 31kg
Dimension Gross W 580mm x D 620mm x H 890mm
Net W 540mm x D 560mm x H 850mm
Accessories Water supply hose, drain hose, owner's manual

2-1 WASHING MACHINE

3. Features
3-1 Dimensions

540
345

1170

850 850

30

3-2 Installation

3-2-1 Level Specifications and Wall - Clearance 3-2-3 Controlling the Front Adjustable Leg
To control the height, turn the adjustable leg.
Distances
1. Install the washing machine on a solid and level
floor.
2. Place the machine at least 10cm away from the wall.
3. Placement on an inclined, weak or rough floor may
cause abnormal trembling.

3-2-2 Balance 3-2-4 Connecting the Drain Hose

See if machine is placeed level by checking the 1. After pressing the joint ring(a), insert the drain hose
position of the washing tub. (b) in the drain direction. (Same as pump model.)

● Open the lid of the machine, pour wster into the tub (a)
up to the level just below the pulsator, and adjust
the legs so that the pulsator is positioned at the
center of the water as shown in the figure.
● Place the machine more than 10cm away the wall
WATER (b)
2. Install the drain hose about 70~80cm
above the ground (for pump model).

SAMSUNG ELECTRONICS CO., LTD 3-1

3. Features

3-2-5 Connecting the water supply hose

1. Romove the adaptor from the 2. First, using a "+" type screwdriver, 3. Connect adaptor to the water tap
water supply hose. loosen the three screws on the by firmly tightening the screws.
adaptor. Then turn part (b), following the
Next, take the adaptor and hold arrow, and put (a) and (b) toge-
parts (a) and (b) with a gap about ther.
5mm between them.

a
a
b
b

4. Connect the water supply hose to 5. Connect the other end of the If the water tap is a screw type,
the adaptor. Pull down part (c) of water supply hose to the inlet connect a water supply hose that
the water supply hose. When part water valve at the back of the fits to the tap as shown.
(c) is released, the hose is washer.
automatically connected to the Screw the hose clockwise, all the
adaptor, and makes a 'click' way in.
sound.

3-2-6 Positioning the Drain Hose

1. When there is no threshold, the length of 4. Other precautions
the drain hose should not exceed 3m.
2. When it is necessary to connect the drain
hose with the drain outlet located far
away, connect the extension hose and
applicable parts (available from dealers
or service centers).

3m
Do not put the end of the drain Do not place the hose below the
hose into the water. floor level of the drain outlet.

3. Do not install the drain hose where it

must extend over a threshold of 5cm or
more ; do not install where there is a
threshold and the hose must extend for
more than 2m.
2m
Do not make the mid part of the If the drain hose must be
hose than the ends positioned positioned at a high angle, install
5cm higher. the washing machine so that it is
in an even higher position.

3-2 WASHING MACHINE

4. Operating Instructions
4-1 Component Identification

LID Option
Be sure to keep the lid WATER SUPPLY HOSE
closed during washing (HOT) Option
and spinning

WATER SUPPLY HOSE

(COLD)

DRAIN HOSE
(PUMP) Option

FABRIC SOFTENER BASKET SPIN

DISPENSER Option

'BOOMERANG"
BLEACH INLET PULSATOR

Option
POWER CORD

MAGIC FILTER SOUND ABSORPTION

Lint will be collected in the PANEL Option
filter during washing.

FRONT CONTROL
Option PANEL Option
GROUND LEAD

ADJUST ABLE LEGS WATER DRAIN HOSE

SAMSUNG ELECTRONICS CO., LTD 4-1

4. Operating Instructions

4-2 Control Panel

1 2 3 4

6 7 8 9

4-2-1 ① REMAINING TIME INDICATOR LIGHT 4-2-5 ➄ Delay Start

1. Button controls and washing processes are 1. This function is to finish the washing operation at
displayed here. the time user set.
2. Each icon is described under its control button. 2. You may change the delay start time by using this
button. (from 3 hours to 18 hours)
4-2-2 ➁ Function Indicator Light
1. In use indicated by a flashing symbol. 4-2-6 ➅ Water Supply (option)
2. The light goes out at the end of the function. 1. Press this button to select water temperature.
2. The selection order is :
4-2-3 ➂ Start/Hold Cold ➝ Cold + Hot ➝ Hot ➝ Cold
1. Press this button to alternately 'start' or 'hold'. 3. Selecting the Wool Course automatically selects
2. This button is a convenient way to change washing cold water (to protect the wool fabric)
courses or a commands.
4-2-7 ➆ Water Level
4-2-4 ➃ Power 1. Press this button to select the water height.
1. Press this button for power ON/OFF. 2. The selection order is :
2. When the washing operation is completed, the Med ➝ High ➝ Extra Low ➝ Low
power automatically turns off and the buzzer 3. Selecting the Wool Course limits the water levels to
sounds off 5 times. high or medium.
3. Allow at least a 3-second interval before turning the
washing machine again . 4-2-8 ⑧ Function
1. The selection order is :
Soak, Wash, Rinse, Spin ➝ Wash ➝ Rinse ➝ Spin
➝ Wash + Rinse ➝ Rinse + Spin

4-2-9 ⑨ Course
1. Press this button to select the type of washing cycle.
Fuzzy ➝ Heavy ➝ Speedy ➝ Woolen

4-2 WASHING MACHINE

 4. Operating Instructions

4-3 Function Descriptions

4-3-1 Water Supply FUNCTION TIME
1. In all the cases of prior to the first press of START/HOLD WASH 18 min
key, during operating or hold state, they follow the below RINSE 15 min
sequences. SPIN 9 min
➝ COLD ➝ COLD + HOT ➝ HOT WASH + RINSE 38 min
RINSE + SPIN 24 min
2. When wool course is selected, water supply is selected
automatically to cold water without key input.
4. This key is used as adjusting function.
3. Once water supply is changed by key input, this water
① Rinsing times are added by one time when function
supply keeps on the changed course. key is pressed under general course operation
In case of wool course, cold water is selected automatically, (FUZZY, HEAVY, SPEEDY and woolen/) and
but if the user'd like to change it to other course, the course function operation (RINSE, WASH + RINSE,
will return to the previous course. RINSE + SPIN, ) as pressing this key.
4. While water supplying, the lamp selected is flashing(one Display is changing as follows.
second ON/OFF) ➝ 2 (times) ➝ 3 ➝ 4 ➝ 5 ➝ 1

4-3-2 Water Level ➁ Washing time is adjusted by press of function

key during washing only operation.
1. In all the cases of prior to the first press of START/HOLD ➝15 (min)➝17➝19➝21➝23➝25➝3➝5➝7➝9➝11➝13
key, during operating or hold state, they follow the below
sequences. ③ Spinning time is adjusted by press of function key
➝MED ➝ HIGH ➝ EXTRA LOW ➝ LOW during spinning only operation.
➝ 5(min) ➝6➝7➝1➝2➝3➝4
2. When WOOL is selected, only HIGH & MEDIUM & LOW
water level is possible.
3. If you change the course to WOOL, in case previous water 4-3-5 Delay Start
level is low or medium, the water level is automatically 1. This function is to finish the washing operation at the time
selected High level and in case previous water level is over user set.
Low, the water level is not changed. 2. If the START/HOLD key is pressed after adjusting of
4. While water is supplying, if the water level is changed, the reservation time by pressing the delay start button,
reservation washing begins.
remaining time is changed. 3. If you push START/HOLD key after selecting reservation
washing, the machine carries out three-hour reservation
4-3-3 Course washing.
4. The first beginning value of reservation washing is 3 hour
1. If this key is pressed before the first press of START/HOLD and the order according to delay start key push is as follow.
key or during HOLD state, the selection order is as follow. ➝ 3➝ 4 ➝ 5➝ ¥¥¥ ➝ 16 ➝ 17 ➝ 18
Even if manual washing is selected already, the selected
course is cancelled, and the course is selected as follow. 5. Once reservation washing is selected, it follows the fuzzy
course selected and reservation washing can not be changed
➝ FUZZY ➝ HEAVY ➝ SPEEDY ➝ WOOL in reservation procedure. But the change of water level and
water supply selection are possible.
2. During operating, all keys except for COURSE SELECTION 6. If the door is opened in the waiting state of normal
key are valid. reservation, it causes the door open error.
But, only START/HOLD is vaild during spin operation.
3. During operating, If anykey is pressed after pressing the 4-3-6 Start/Hold
START/HOLD key, new Selection course is performed, not
related to previous course. 1. Available only after selecting a course.
4. This key is invalid during operation. 2. Sequence : ➝ START ➝ HOLD ➝ START

3. The display shows the remaining time, including the current

4-3-4 Function Button function, when in 'start' status.
The time decreases 1-min at a time.
1. This key is valid except for weight sensing operation. When in 'Hold' status, the time stays as it is.
2. After START/HOLD during operation or under reset
condition, as pressing this key display is changing as
follows. 4-3-7 Power
➝SOAK, WASH, RINSE, SPIN➝WASH ➝RINSE ➝SPIN 1) This key is always available when the power cord is
connected.
➝WASH + RINSE ➝ RINSE + SPIN ➝INITIAL STATE 2) sequence : ➝ ON ➝ OFF ➝ ON
3. The beginning conditions are as follows when function key 3) After finishing operation, this key is automatically turned
is selected. (ex.High Level) off.

SAMSUNG ELECTRONICS CO., LTD 4-3

4. Operating Instructions

4-4 Description of Technical Points

4-4-1 Weight Recognizing Function

1. Weight recognizing function works first washing

operating before water is supplied, not in WOOL 3. If the water level does not reach to the water level
course and Manual function operation (Wash, selected for 60minutes after starting water
Rinse, Spin, ¥¥¥) supplying, the water supplying Error is displaying
on the display.
2. Weight recognizing function is cancelled when
water level key is pressed prior to the completion of 4. Supplementary water supplying is performed
weight recognizing function. every Washing or Rinsing operating. The steps are
as follows.
3. If the current water level is above lowest at the ● supply water to the water level selected,
beginning of weight sensing, it is automatically ● perform the washing or Rinsing operation for 1.5
decided as a high level. minutes.
● sense the present water level after stopping
4. If you change courses after sensing weight, the high Motor.
water level is automatically selected irrespective of ● compare the present water level to the water
the water level decided by the sensing of weight. level selected.
● if present water level < the water level selected,
supply water to the water level selected.
if present water level ³ the water level selected,
continue the washing or Rinsing operation.
● But total time of supplementary water
4-4-2 Water Supplying Function supplying is not over 60 seconds.

1. Relations between water level, frequency & water

supply capacity.
unit :ı fre : KHz
4-4-3 Soak Function
amount of water
fre
supplied
1. This function works only when Soak washing is
RESET 0 24.80 selected by function select key.

EXTRA LOW 28 ı 23.80 2. It works repeatedly during set time by every 5

minutes(operation for 1 minute and pause for 4
LOW 35 ı 23.40 minutes) for 30 minutes after water is filled to
selected water level.
MEDIUM 43 ı 23.00
3. If water level is set higher during the Soak
HIGH 50 ı 22.50 procedure, Soak procedure stops and water is
refilled, and then, keeps on going the Soak
procedure.
2. Relations between Hot/Cold selection & cycle.
4. Washing cycle of 15 minutes begins after Soak
Hot/Cold Supplementary Pre function completion.
Wash Rinse Remarks
selection Water supply spinning Rinsing times can be adjusted according to Soak
washing procedure.
Cold Cold Cold Cold Cold

Hot / Cold Hot / Cold Hot / Cold Hot / Cold Hot / Cold
4-4-4 Fuzzy Function
Hot Hot Hot / Cold Hot / Cold Hot / Cold This function recognizes the quantity of laundry
load and selects the water level by itself and keep
❈ The rinse of two times is selected to cold
on going washing operation automatically.
water automatically.

4-4 WASHING MACHINE

4. Operating Instructions

4-5
(Unit: minute)
Wash Rinse 1 Rinse 2 Rinse 3 Spin
Function Water Water Water Intermittent Water Water Intermittent Water Water Intermittent Water Water Intermittent Remained time
Soak Wash Spin Stop Rinse Spin Stop Rinse Spin Stop Rinse Spin Stop Min. sec.
course level supply drainage spin supply drainage spin supply drainage spin supply drainage spin for wash
Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec.
High 3 0 15 0 1 30 1 0 1 30 1 30 5 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 30 44 150 46 min. 30 sec.
Medium 2 30 15 0 1 15 1 0 1 30 1 30 4 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 30 41 195 44 min. 15 sec.
Fuzzy
Low 2 0 15 0 1 0 1 0 1 30 1 30 4 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 30 40 60 41 min. 00 sec.
Small 1 30 15 0 0 45 1 0 1 30 1 30 2 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 0 45 1 0 4 0 30 34 285 38 min. 45 sec.
High 3 0 18 0 1 30 1 0 1 30 1 30 5 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 1 30 47 150 49 min. 30 sec.
Medium 2 30 18 0 1 15 1 0 1 30 1 30 4 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 1 30 44 195 47 min. 15 sec.
Strong
Low 2 0 18 0 1 0 1 0 1 30 1 30 4 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 1 30 43 60 44 min. 00 sec.
Small 1 30 18 0 0 45 1 0 1 30 1 30 2 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 0 45 1 0 4 0 1 30 37 285 41 min. 45 sec.
High 3 0 5 0 1 30 1 0 1 30 1 30 5 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 1 30 32 150 34 min. 30 sec.
Medium 2 30 5 0 1 15 1 0 1 30 1 30 4 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 1 30 29 195 32 min. 15 sec.
Save
Low 2 0 5 0 1 0 1 0 1 30 1 30 4 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 1 30 29 60 30 min. 00 sec.
Small 1 30 5 0 0 45 1 0 1 30 1 30 2 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 0 45 1 0 4 0 1 30 23 285 27 min. 45 sec.
High 3 0 6 0 1 30 1 0 1 30 1 30 5 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 1 30 29 150 31 min. 30 sec.

SAMSUNG ELECTRONICS CO., LTD

Wool Medium 2 30 6 0 1 15 1 0 1 30 1 30 4 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 1 30 26 195 29 min. 15 sec.
Low 2 0 6 0 1 0 1 0 1 30 1 30 4 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 1 30 26 60 27 min. 00 sec.
4-5 Program Chart

High 3 0 30 0 15 0 1 30 1 0 1 30 1 30 5 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 1 30 74 150 77 min. 30 sec.

Medium 2 30 30 0 15 0 1 15 1 0 1 30 1 30 4 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 1 30 71 195 74 min. 15 sec.
Fuzzy
(soak)
Low 2 0 30 0 15 0 1 0 1 0 1 30 1 30 4 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 1 30 70 60 71 min. 00 sec.
Small 1 30 30 0 15 0 0 45 1 0 1 30 1 30 2 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 0 45 1 0 4 0 1 30 64 285 69 min. 45 sec.
 WASHING MACHINE
(Unit: minute)
Wash Rinse 1 Rinse 2 Rinse 3 Spin
Function Water Water Water Intermittent Water Water Intermittent Water Water Intermittent Water Water Intermittent Remained time
Wash Spin Stop Rinse Spin Stop Rinse Spin Stop Rinse Spin Stop Min. sec.
course level supply drainage spin supply drainage spin supply drainage spin supply drainage spin for wash
Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec. Min. Sec.
High 3 0 15 0 18 0 18 min. 00 sec.
Medium 2 30 15 0 17 30 17 min. 30 sec.
Wash
Low 2 0 15 0 17 0 17 min. 00 sec.
Small 1 30 15 0 16 30 16 min. 30 sec.
High 3 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 14 60 15 min. 00 sec.
Medium 2 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 12 105 13 min. 45 sec.
Rinse
Low 2 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 12 30 12 min. 30 sec.
Small 1 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 9 135 11 min. 15 sec.
High 1 30 1 0 5 0 1 30 8 30 08 min. 30 sec.
Medium 1 15 1 0 5 0 1 30 8 15 08 min. 15 sec.
Spin
Low 1 0 1 0 4 0 1 30 7 0 07 min. 00 sec.
Small 0 45 1 0 4 0 1 30 6 45 06 min. 45 sec.
High 3 0 15 0 1 30 1 0 1 30 1 0 3 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 36 120 38 min. 00 sec.
Medium 2 30 15 0 1 15 1 0 1 30 1 0 2 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 33 180 36 min. 00 sec.
Wash
Rinse
Low 2 0 15 0 1 0 1 0 1 30 1 0 2 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 33 60 34 min. 00 sec.
Small 1 30 15 0 0 45 1 0 1 30 1 0 1 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 28 240 32 min. 00 sec.
High 3 0 2 0 1 30 1 0 1 30 1 30 3 0 2 0 1 30 1 0 5 0 1 30 22 90 23 min. 30 sec.
4. Operating Instructions

Medium 2 30 2 0 1 15 1 0 1 30 1 30 2 30 2 0 1 15 1 0 5 0 1 30 20 120 22 min. 00 sec.

Rinse
Spin
Low 2 0 2 0 1 0 1 0 1 30 1 30 2 0 2 0 1 0 1 0 4 0 1 30 19 30 19 min. 30 sec.
Small 1 30 2 0 0 45 1 0 1 30 1 30 1 30 2 0 0 45 1 0 4 0 1 30 15 180 18 min. 00 sec.

4-6
 6. Disassembly and Reassembly
6-1 Cautions for Disassembly and Reassembly

6-1-1 Before Servicing

1. When laying down the washing machine for repair, Shape
do not place the front side downwards. This may
cause the following :
¥ The round front face may be deformed. CASE-D BAR-S SPRING COLLOR-S
¥ The top-cover and the outer-case (round area) may
not match. Front White Yellow Yellow Red
Rear White Yellow Yellow NTR

2. When removing the top-cover from the outer-case,

remove 2 serews fixing the parts in back of the top-
cover and remove the top-cover while pushing it in
the direction of the front at the same time lift up
quietly the rear side. 3. When replacing the suspension-bar, only use parts
for this model.
Caution) When you do not remove like that 2 fixing 4. Since the length of the bar varies among on models,
hooks easy to break in the front side. installing the wrong size may cause severe
vibration.
5. Do not deform the check-S/W rod of the top-cover.
6. The installation of a deformed check-S/W rod will
result in malfunction of the safety switch during
severe vibration, thus causing an unbalanced error.

3. When removing the top-cover from the outer-case,

do not let the wire bundle fall downwards and
touch the sharp edge of the outer-case. Also, do not
allow tension to stress the wires.

6-1-3 After Servicing

1. Check the level of the washing machine.
2. When setting the wire bundle in the lower section,
make sure that the wire bundle is not stressed by
4. When moving the washing machine to a place with any tension due to tilting of the tub assembly.
a rough floor, do not drag it. If it is dragged, the 3. When setting the wires, do not let the wires touch
rubber may get loose, thereby causing severe any sharp edges.
vibration and noise during washing. 4. Remove any moisture on the wire bundle, and on
areas surrounding the wire connector.

6-1-2 During Servicing

1. When replacing the suspension-bar, be sure to
check both the front and rear suspension-bar
assemblies. This prevents installation of the front
and rear sides in the reverse order.
2. Reversal may cause a severe vibration that might
rock the washing machine.

SAMSUNG ELECTRONICS CO., LTD 6-1

6. Disassembly and Reassembly

6-2 Disassembly

Disassembly Procedure Illustration Remarks

● Removing the Top cover and PCB Assembly

1) Remove 2 serews fixing the parts in back of the top-cover.
2) Remove the top-cover while pushing it in the dirfction of the
front at the same time lift up quietly the rear side.
3) Reverse the top cover.
4) Loose 5 screws for fastening the PCB-Assembly.
5) Take out the PCB-Assembly.

● Removing the Pressure-Sensor, Water-Valve, Checker

Assembly, and Transformer

1) Remove two Screws fixing the Top-Cover and the Cover T.C.
2) Lift up the Cover TC while pushing it in the direction of the arrow.

● Pressure Sensor
1) Pull out the Lead Wire Terminal of the Pressure Sensor.
2) Remove the Pressure Sensor.
3) Pull out the Air Hose.
PUSHING

● Water Valve
1) Pull out the Lead Wire Terminals.
2) Remove the Water valve while pushing it in the direction of the
arrow.

● Checker
1) Pull out the Lead Wire Terminals.
2) Remove the two Screws.
3) Lift out the Checker.

● Wire Harness
1) Pull out the Lead Wire Terminals from the PCB.
2) Pull out the Lead Wire Terminals from the parts in back of the
Top Cover.
3) Remove the Wire Harness.

● Transformer
1) Transtomer is built in the PCB Assembly.

6-2 WASHING MACHINE

 6. Disassembly and Reassembly

Disassembly Procedure Illustration Remarks

❍ Removing the Motor

1) Remove the Back Cover.

2) Lay down the Washing Machine with the rear side facing the
floor.
3) Pull out the Sound Absorption Panel.
4) Remove the Wire Housing.
5) Remove the V Belt.
6) Remove the two Bolts fastening the Motor.
7) Remove the Motor Pulley.
8) Pull out the Motor

❍ Removing the Drain Motor

1) Lay down the Washing Machine with the rear side facing the
floor.
2) Pull out the Lead Wire Terminal.
3) Remove the Bolt.
4) Remove the Drain Motor Wire from the Link.
5) Lift out the Drain Motor

❍ Removing the Shaft Assembly

1) Remove the two Screws fixing the Top Cover, and lift up the Top
Cover gently tilt the Top Cover back to expose the Tub Cover.
2) Remove the four Screws fixing the Tub Cover.
3) Remove the Bolt fixing the Pulsator.
4) Remove the Spin Nut fixing the flange Shaft and the Shaft and
pull out the Spin Basket.
Caution
● Disassemble the Spin Nut in a counterclockwise direction.

5) Lay down the Washing Machine with the rear side facing the
floor.
6) Remove the two Bolts fixing the Saddle.
7) Remove the four Bolts fixing the Shaft using the Box and take out
the Shaft Assembly.

❍ Removing the Pump Assy

1) Remove the Back Cover. SCREWS

2) Remove the Lead Wire Terminal and the Earth Wire.

3) Remove the Two Hoses.
4) Remove the 2screws which fix the filter.
5) Lay down the Washer with the right side facing the Floor.
6) Remove the 2 Screws which fix the pump. SCREWS

SAMSUNG ELECTRONICS CO., LTD 6-3

6. Disassembly and Reassembly

6-3 Spin - Nut Repairing Box

6 HANDLE

5 CONNECTING ROD

4 GUIDE
3 JIG PIN

2 SPIN NUT

1 SHAFT

6-3-1 Procedure 3. Insert the connecting rod ° and handle Å into the
square box. Then turn the handle clockwise on the
1. Insert the jig  into the spin-nut - .
axis of the small box to disassemble (Right-hand
thread).*
2. Insert the guide pin à into the groove of the flange -
shaft by rotating it to the right and left.

LOOSEN LOCK
Guide Pin
Inserting Point

SPIN
BASKET *To disassemble the box, give three to four times of
FLANGE instantaneous shocks to the handle in the
SHAFT loosening direction, then disassemble it by turning
the handle when the nut is loosened.

4. To disassemble the box, strike the handle three or

four times-quick shocks to loosen it-then complete
the disassembly by turning the handle as the nut is
loosened.

5. Reassemble in reverse order.

6-4 WASHING MACHINE

7. Troubleshooting
7-1 Self - diagnostic Functions (Buzzer Alarm)

If there is a problem during operation, the following error conditions are shown on the LED display, and the
washing machine stops its operation.
Error Condition Buzzer Solution
Water level sensor error Water level sensor fails to send The buzzer sounds five times Press the "Power"
signal for longer than 15 seconds. with a 0.5sec. ON/0.5sec. OFF button. No other
cycle. buttons work.

Auto - off error Power does not turn off despite 3 the buzzer sounds five times Press the "Power"
power-off trials by program with a 0.5sec. ON/0.5sec. OFF button.
cycle. Another buttons do
not work.

Water supply error No frequency change for 60 The buzzer sounds five times Press the "Power"
minutes from water supply. with a 0.5sec. ON/0.5sec. OFF button.
cycle. No other buttons
work.

Drain error Water level does not decrease to The buzzer sounds five times Press the "Power"
the reset point within 6 minutes with a 0.5sec. ON/0.5sec. OFF button.
from draining water. cycle. No other buttons work.

Door open error Door is open during The buzzer sounds five times Close the door.
dehydration cycle. with a 0.5sec. ON/0.5sec. OFF
Only to raise at spin. cycle.

Pressing "start" button stop

the buzzer.
No buttons work.
Unbalance error An unbalanced load is sensed three The buzzer sounds five times Open the door.
times during dehydration cycle. with a 0.5sec. ON/0.5sec. OFF Balance the laundry.
cycle. Close the door.

Pressing "start" button stops

the buzzer.
No other buttons work.
Overflow error It takes place in case the over The buzzer sounds five times Put off the power
flow rises for three times. with a 0.5sec. ON/0.5sec. OFF and restart.
cycle.

Put off the power and restart.

SAMSUNG ELECTRONICS CO., LTD 7-1

7. Troubleshooting

7-2 Test Mode

7-2-1 Test Mode : WATER LEVEL + POWER

1. Entering : Press the power key while pressing down the WATER LEVEL button.

2. Ò Ò is displayed on the display.

3. If you press the COURSE key, the test mode changes step by step.
➝ 01 ➝ 02 ➝ 03 ➝ 04 ➝ 05 ➝ 06

4. The test is conducted if you press the START/HOLD key when the test mode is in a display state.

5. Each mode description

MODE NO DISPLAY TEST DESCRIPTION REMARKS

Aging test in driving part and then, driving part and

1 display are turned ON/OFF for 1 second.

Repeating 5 min. dehydration and 3 min. stop without draining.

2 It read Lid open and unbalance and shows them.
It shows this on the indicator.

Operate the washing cycle after suppling water

3 to high level.

Indicate the input value of weight sensing pulse

4 with hexa value.

* Mode , are only for manufacturing process.

7-2 WASHING MACHINE

 7. Troubleshooting

7-3 Servicing Precautions

When trouble shooting or parts, be sure to observe 5.Be sure to use only authorized replacement parts.
the following.
6. AC 110V-220V is applied between T1 and T2 of the
1. Be sure to let the resistance of 1 M½ contact the
triac on the P.C.B Therefore, touching the radiating
human body before grounding. When it is
plate accidentally may cause electric shock. Also,
impossible to ground, let the human body contact
the P.C.B. Both high and low voltages exist on the
the power plug and the grounding wire once to
P.C.B.
eliminate the potential damaging shock hazard.
¥ After replacing the controller, the defective parts
7. Do not replace any parts on the board, except the
should be returned to the suppliers of these parts
tact switch on the P.C.B. assembly is in trouble. The
for root-cause analysis and incorporation into for
P.C.B assembly is treated with an insulation
future product planning. At the time of return, be
coating, the enhanced moisture-proofing.
sure to pack them together with repair parts.
Otherwise, it is impossible to perform root cause
8. When you suspect that the operation of the micom
analysis due to the static electricity.
is faulty, take actions in accordance with the
specified troubleshooting procedures. Do not
attempt to replace the entire P.C.B. assembly
without first doing a root-cause analysis.

9. Because the parts installed in the P.C.B. are treated

with a urethane coating, they cannot be inspected
<Notice on disassembly and repair> by the test bar. Therefore, first check the lower parts
for any abnormality using the lead wire of the
2. The wiring should be properly connected in housing (LP-09-1). Going down connected with the
accordance with the wiring diagram. Erroneous P.C.B.
wiring may cause faulty operation, smoke, or fire.

3. Be sure to pull out the power plug during repair.

4. Special attention should be paid to connection,

insulation treatment, and wiring work for the lead
wire.
¥ The lead wire should be soldered, and insulation-
treated with vinyl tape, or connected to the
pressure connection terminal for drain treatment.
¥ When connecting the lead wire, take care not to let
it touch hight components of metal sugared. This is
a "wloow"

SAMSUNG ELECTRONICS CO., LTD 7-3

7. Troubleshooting

7-4 Troubleshooting
7-4-1 Troubleshooting of the Power Supply Board
If any of the following occurs, the PCB is defective. Replace the PCB.
1. Pressing a selection button illuminates the LED display, but the buzzer does not sound.
2. Pressing a selection button sounds the buzzer, but does not illuminate the LED.
3. Pressing a selection button illuminates the wrong LED.

Insert the power plug into the receptacle and press the Power button. If the stored parameters do not display,
check the following :

The power does not turn on.

YES

Is the power NO
Connect the power plug securely.
plug connected?

YES

YES
Is the fuse blown? Replace the fuse.

NO

Is the
connection of the power NO
Check the harness.
trans harness OK?

YES
Replace the PCB assembly.

7-4-2 Keyboard
¥ When pressing a selection button, the buzzer does not sound, or the LED does not display.

There is no buzzer sound, and the

LED display does not turn on.
YES

Is the power NO
Turn the power switch on.
switch turned on?

YES

Are the contacts of the NO

Replace the selection switch (tact switch).
selection switch OK?

YES
Replace the PCB assembly.

7-4 WASHING MACHINE

 7. Troubleshooting

7-4-3 Driving Unit

¥ Water supply Error

Water is not supplied.

YES

Is the
Start/Hold button NO Press the Start/Hold button.
pressed after selecting Open the faucet.
the course?

YES

Does the
water valve make a YES NO
"Jee" sound when water is Is the fauct open? Open the faucet.
supplied ?

Securely connect the YES

NO
terminal

NO Is the connection Is the water YES Close the faucet, pull out the water
of the water valve terminal supply stopped?
all right? hose and turn it off.

YES NO

Is the Is there
winding wire of the any foreign material YES Clean the water valve filter with a
water valve electrically attached to the water hose and
the water valve toothbrush, etc.
connected?
filter?

NO NO
YES

Is the Replace the water valve.

connection of the
water valve with the water YES
level sensor terminal
OK?

NO
YES
Does the pulsator rotate? Replace the water level sensor.

NO

Replace the PCB assembly.

SAMSUNG ELECTRONICS CO., LTD 7-5

7. Troubleshooting

¥Water Stop Error

The water supply does not stop.

YES

Pull out the plug.

YES

The water valve is defective.

NO
Does the water supply stop? * Remove the foreign material in
the water velve.

YES

Is there water in YES Air is leaking. Check the connection,

the water level sensor
and apply the adhesives.
hose?

NO

Is the water level YES

Correct the bent hose.
sensor hose bent?

NO

Is the
water coming out Remove foreign materials such as
through the drain hose with YES
Check the drain valve.
the operation of the drawn thread, hair, pin and buttons.
drain valve?

NO

Replace the PCB assembly.

¥ Washing is started without water supply.

Washing starts without water spply.

YES

Is the connection NO
of the water level sensor Connect the terminal securely.
terminal OK?

YES

NO
Does washing continue? Turn off the power, and then start again.

YES
Replace the PCB assembly.

7-6 WASHING MACHINE

 7. Troubleshooting

¥ The pulsator does not rotate during washing.

ã This malfunction may be caused by defective contacts of the wire harness.

The pulsator does not rotate.

YES

Does the water Is the connection

NO YES
supply stop after filling to the of the water level sensor Replace the water level sensor.
specified level? terminal all right?

NO
YES
Connect the terminal securely.

Does the YES

motor make a "woong" Replace the condenser.
sound?

YES
NO Is water supplied?

NO
Now it is normal
Does the pulsator
operate normally? NO

Check the motor for short -

circuit, and replace it if Replace the PCB assembly.
necessary.

Does the pulsator NO

operate normally?

YES
Is the V belt NO
positioned correctly? Install the V belt correctly.
The motor is defective.
Check for a racing motor due to
excessively strong or weak tension of
YES the V - belt.

Replace the PCB assembly.

SAMSUNG ELECTRONICS CO., LTD 7-7

7. Troubleshooting

¥ Defective Rotation during Washing

The pulsator rotates one - side.

YES

Is the connection NO
of the housing all right? Securely connect it.

YES

Is the winding
wire on the one side of the motor
YES
Replace the motor.
disconnected?

NO
Replace the PCB assembly.

¥ Noise Occurs during Washing.

Noise coccurs during washing.

YES

Does the noise YES

occur from the inside of the
washing tub?
Are there
any foreign materials YES
stuck between the washing net Remove any foreign materials.
and the pulsator?
NO
NO

Adjust the clearance of the pulsator.

Is there noise YES

from the clutch?

Is the position
NO of the brake lever adjusted
properly?

YES Is there noise

from the motor? The noise is either the contact noise inside
YES
the clutch, or it is noise caused by the wear
and deformation of parts.
Contact noise due to the
wear of motor bearing NO
1. Check the fastening screws for the motor
and the motor pulley.
2. Check the caulking of the motor pulley.
Noise of loosing screws YES 3. Check the internal components for any
from the connection area. abnormality.

(The following soond does not indicate any problem :

The "Sha" sound generated during the stop of the dehydration tub is the sound of the water moving by automatic
balance in the dehydration tub.)

7-8 WASHING MACHINE

 7. Troubleshooting

¥ Defective Dehydration

Dehydration is not effective.

YES

This is normal : A three

YES
Is the water being drained? minute water crwn occurs
(In case of drain error, dehydration before dehydration.
is inoperative.)
NO

YES
Does the pulsator rotate?

NO
Any operating YES The clutch is defective.
sound from the drain motor
Is the tension heard? Repair it.
YES
Adjust the tension. of the V - belt excessively
high or low?
NO

NO Is the NO
drain motor electrically Replace the drain motor.
YES connected?
Tell the customer to close the lid. Is the lid open?
YES

NO
Is operation of NO The drain motor is
the drain motor alone
Is the terminal possible? short - circuited.
After checking, YES
of the safety switch lifted up
adjust the safety switch. when closing the YES
lid?

NO Replace the PCB assembly.

Is there
NO continuity between
Replace the safety switch. the safety switch COM and
the door terminal.

YES
One or two unbalances
automatically corrected through YES
the process of water supply Is the load unbalanced?
and washing.

NO
(The third time causes an
Short - circuited motor. When
"unbalance error".
Spread the laundry evenly, Is operation the motor makes a "woong"
NO
and start again.) of the motor alone sound, the condenser ia
possible? defective, or one side of the
motor windings is shorted.
YES

Change the PCB assembly.

SAMSUNG ELECTRONICS CO., LTD 7-9

7. Troubleshooting

¥ Draining Water is not Possible.

Water cannot drain.

YES

NO
Is the drain hose lowered? Lower the hose.

YES

YES
Is the drain hose bent? Correct the hose.

NO

Press the Start/Hold button 3 to

4 times during the drain and
dehydration cycles.

Any there
NO
operating sounds from the
drain motor?

YES
Is the NO
Is the drain motor electrically Replace the drain motor.
YES wire connecting the connected?
Securely connect it drain valve and the drain
motor dropped
out? YES
NO
Is operation NO
of the drain motor alone The drain motor is shorted.
Is the possible?
YES
outlet of the drain hose
clogged?
YES
Remove the foreign material NO
completely. Is the wire NO
connection secure? Securely connect it.
Has there drawn
thread, or the like attached to
YES the drain valve? YES

NO Replace the PCB assembly.

Pull out the spin basket.

Is there any foreign

YES material attached to the
drain outlet?

NO

Now it is normal.

7-10 WASHING MACHINE

 7. Troubleshooting

¥ No draining. (With PUMP MODEL)

No draining.
YES

Is there any Remove the foreign matercal

YES
operating sound of
Pump - Drain? from the Filter - Case.

NO

Does the motor YES Is the wire connection Connect it firmly.

drain operate? of pump OK?

NO NO

Fault on PCB assembly. Fault on Pump - Drain.

Relace it. Replace it.

7-4-4 Inspection After Repair

Inspection Item Description

Check grounding Check that the original grounding wire of the washing machine is securely grounded.
Connection of the grounding wire? wire to a gas or water pipe made of vinyl chloride is
very dangerous.

Check the safety Check the operation of the brake. If the following braking times are exceeded, readjust
system or repair the brake system.

Load Braking Time

No load Below 7 seconds
Rated load (5.0/5.5kg) Below 10 seconds

Dressing the lead wires Tie the lead wires with a separate wire to prevent them from scattering.
Check that they are securely connected.

Check the locking nuts and screws Check that the nuts and screws are securely locked, and be sure to apply screw lock.

Check inside the washing machine Check for any vinyl wires, screws, or foreign materials inside the washing machine.

Check for oil (lubricant) or In particular, check the surrounding areas of driving units for oil (lubricant) leakage, and
water leakage check the moving parts of the drain valve for water leakage.

Checking the connection of the Check the power cord, plug, and receptacle for any damage. Make sure they comply
power cord with the working voltage.

Adjustment of horizontal level Adjust the height of the two adjusting legs (front of the washing machine) so that
of the washing machine the washing machine is horizontally level.

SAMSUNG ELECTRONICS CO., LTD 7-11

8. Exploded Views

12
13
4

15
16
14

7
19
8
9
10
11

18

17
2 2-1

20

8-1 WASHING MACHINE

 NO. CODE-NO DESCRIPTION SPECIFICATION Q’TY REMARK

1 DC64-00015B NLAY-PANEL COLD*ONLY 1 ENG

2 DC96-00062A ASSÕY-P.C.B URETHAN SW70A1(P) 1 COLD ONLY220V/50HZ
2-1 DC26-00002A TRANS-FORMER SW70A1(P) 1 220V/ 50,60HZ
3 DC97-00161A ASSÕY LID T.C ABS(CRYSTAL) 1 SW70A1(P)
4 DC61-00062A SPRING-Q(R) STS304 1
5 DC61-10729C COVER-T.C ABS(L/GRY) 1 SW70A1
DC61-10729D COVER-T.C ABS(L/GRY) 1 SW70B1
6 DC62-30310H VALVE-WATER HOT 1 110/120V/50.60HZ
DC62-30310E VALVE-WATER HOT 1 220/240V/50,60HZ
7 DC62-30310G VALVE-WATER COLD 1 110/120V/50.60HZ
DC62-30310F VALVE-WATER COLD 1 220/240V/50,60HZ
8 DC62-00004A HOSE-INLET NBR 2
9 DC62-00012A FILTER-GUIDE FOAM 1
10 DC65-10001B CABLE-TIE DA-100 4
11 DC61-00020A GUIDE-WATER PP,NTR 1 HOT*COLD
DC61-00020B GUIDE-WATER PP,NTR 1 COLD ONLY
12 DC90-11054S ASSÕY-CHECKER S/W SW70A1 1 NO-COVER
13 DC32-30006M SENSOR-PRESSURE DN-S12 1 TERMINAL-TYPE
14 DC66-10003A WIRE-VINYL L180 1
15 DC61-20226J DOOR-HINGE(L) POM 1 L/GRY
16 DC61-20226K DOOR-HINGE(R) POM 1 L/GRY
17 DC96-00055A ASSÕY-MAIN WIRE HARNESS SW70A1 1 COLD-ONLY
DC96-00040A ASSÕY-MAIN WIRE HARNESS SW70A1 1 COLD*HOT
18 3601-000485 FUSE-FERRULE 250V,10A 1
19 DC61-10728B COVER-TOP ABS(L/GRY) 1 SW70A1(P)
20 DC34-30006H SWITCH REED 5V,0.3A 1

SAMSUNG ELECTRONICS CO., LTD 8-2

8. Exploded Views

1
11
10

2 12

4
5
6 13

14

7-1 8

15
7-2
7-3

7-4 15-1 16
7-5

7-6 17
PLASTIC
9

18
8
19
7-1

9-1
20

9-2

26
21
9-3 27

28
9-4
22
29

23
75
30
24
STAINLESS
25
31

8-3 WASHING MACHINE

 NO. CODE-NO DESCRIPTION SPECIFICATION Q’TY REMARK
1 DC61-10236A COVER-TUB PP 1
2 DC60-00004A BOLT-PULSATOR M6*20.5, STS 1
3 DC66-50194A PULSATOR PP 1
4 DC60-60003B WASHER-PULSATOR 1
5 DC60-50004A NUT-SPIN ALDC M24 1
6 DC60-60015A WASHER-PLAIN 24.2-35*T1.0, STS304 1
7 DC97-00113A ASSÕY-S.BASKET SPIN SW70A1(P), SW70B1(P) 1 PP
7-1 DC97-00033A ASSÕY-BALANCER P.P,PANTON-COOL GRY 1
7-2 DC61-60524A GUIDE-W/F PP, WATER-FALL 1
7-3 DC61-60525A GUIDE-W/F PP, FILTER 1
7-4 DC61-30123A BASKET-SPIN PP 1
7-5 DC66-40010A FLANGE-SHAFT ALDE 1
8 DC97-00114A ASSÕY-FILTER ABS 1 MAGIC-FILTER
9 DC97-00155A ASSÕY-S.BASKET SPIN SW75A1(P),SW75B1(P) 1 STAINLESS
9-1 DC61-00016A GUIDE-W/F WATERFALL 1 FOR STAINLESS
9-2 DC61-00015A GUIDE-W/F FILTER 1 FOR STAINLESS
9-3 DC61-30124A BASKET-BOWL P.P 1 FOR STAINLESS
9-4 DC61-30125A BASKET-WAPPER STS 1 STAINLESS
10 DC61-30100A TUB-OUTER PP 1
11 DC62-10293A HOSE-DRAIN EPDM,245mm 1 PUMP
12 DC62-10092C HOSE-PUMP EPDM, 349.5mm 1 PUMP
13 DC61-70063A DIE-MOTOR SBHG1 1
14 6046-000311 STAND OFF NYLON66 5
15 DC91-10255A ASSÕY-CASE D.V 1 NO PUMP
15-1 DC91-10363A ASSÕY-CUFF HOSE EPDM(154mm) 1 NO PUMP
16 DC66-30027C LINK POM 1 BLK
17 DC31-20014B MOTOR-DRAIN 220/240V 50HZ,60HZ 1 BKT-HIGH
18 DC62-50011F CONDENSER-M.F 400VAC 12uF 1 220V/50HZ
19 DC61-40077A HOLDER-CONDENSER PP 1 60HZ
20 DC96-00056A ASSÕY-WIRE HARNESS SW70A1 1
DC96-00039A ASSÕY-WIRE HARNESS SW70A1 1 NO PUMP
21 DC61-60026A CUSHION-MOTOR FRPP 2 PUMP
22 DC31-00005A MOTOR-WASH 220V 50HZ 1
23 DC91-11258U ASSÕY-SCREW M8*30 2
24 DC66-10174A PULLEY-MOTOR 50HZ 1
25 DC60-50150A NUT-HEX M8*6.5 2
26 DC97-00347A ASSÕY-SHAFT SEM-50D1(SEC) 1
27 DC60-80017B PIN-LINK 1
28 DC91-11258E ASSÕY-SCREW M8*20 4 PUMP
29 DC66-10045D BELT-V M20.5(M20.6) 1
30 DC61-40053B SADDLE EGI 1 50HZ
31 DC60-20064C SCREW-TAPPING 6.2*20 2

SAMSUNG ELECTRONICS CO., LTD 8-4

 4
5

1
2

10
11

12

13

14

8-5 WASHING MACHINE

 8. Exploded Views

NO. CODE-NO DESCRIPTION SPECIFICATION Q’TY REMARK

1 ASSY-WIRE EARTH 2.6m 1 OPTION

2 DC90-10065C ASSÕY-POWER CORD 1
3 DC61-10226A COVER-BACK PP 1
4 DC97-00121A ASSÕY-DAMPER FRONT/RED 2
DC97-00121B ASSÕY-DAMPER REAR/NTR 2
5 DC97-00107A ASSÕY-FRAME SBHG1-A 1 NO PUMP,NO-HANDLE
DC97-00107B ASSÕY-FRAME SBHG1-A 1 PUMP, NO-HANDLE
6 6046-000310 STAND OFF 7
7 ASSÕY-PUMP DRAIN 1
8 DC91-11905A ASSÕY-BASE PP 1
9 DC61-30314A BASE PP 1
10 DC97-00170A ASSY-LEG SW70A1(P) 2
11 DC61-50009C LEG-ADJUST PP 2
12 DC61-50015B LEG-RUBBER BUTYL,SW70A1,BLK 4
13 DC61-20211A (PAN-SILENT)SHUTTER PP 1 OPTION
14 DC91-11790A ASSÕY-HOSE WATER EXP/1.0M/COLD 1 NIX

SAMSUNG ELECTRONICS CO., LTD 8-6

5. Schematic and Circuit and PCB Pattern Diagram
5-1 Schematic Diagram

SAMSUNG ELECTRONICS CO., LTD 5-1