Solution Pet110 2014

PART A: Short-answer questions (50%; each worth 2%)
Your answers should be brief (just a few words) and may be written on these
pages if you wish. Remember to hand these pages in with your other exam pages!
1. The figure here is from a geophysical survey carried out over a salt dome. What kind of
survey was it and what property of the salt is instrumental in producing such a map?
 magnetic survey
 small negative
magnetic susceptibility
2. The figure here shows another geophysical survey carried out over the same salt. What
kind of survey was it and what characteristic of the salt would yield such a map?
 gravity survey
 relatively low density
3. To represent a seismic signal without aliasing, how densely must it be sampled if the
highest frequency in the signal is 125 Hz?
 ts = 0.004 s -or- fs = 250 Hz
4. How would the P-wave velocity of a porous, water-saturated sandstone change if some of
the water were replaced by natural gas?
 It would decrease.
5. As a seismic wavelet propagates further and further through a rock medium, what
happens to its amplitude spectrum?
 It decreases overall, and gets narrower due to greater loss of higher frequencies.
6. When a P-wave strikes the interface between two rock layers at normal incidence (angle of
incidence = 90), what waves travel on from there, and which way?
 Reflected P travels vertically upward and transmitted P travels vertically downward (no S).
7. 2D seismic data are acquired along a 1D line on the surface. 3D seismic data are acquired
over a 2D area of the surface. How is 4D seismic data acquired?
 as identical 3D surveys repeated at different times (i.e. with time lapses)
8. The acoustic impedance of a rock layer is a parameter that may be calculated from some
other common rock parameters. Write down an expression for this calculation in words,
not just symbols (unless you define the symbols).
 acoustic impedance = density x P-wave velocity
9. What kind of mathematical curve (or function) might we see for the traveltime curve (or
function) on a seismic shot gather representing the reflection from the dipping base of a
single layer?
 a hyperbola shifted in the updip direction
10. What do we call a seismic gather in which each trace has the same shot-receiver distance?
 a common-offset gather
11. Write down an equation that expresses Snell’s law.
 p = (sin)V = constant -or- (sin)V = (sin)V
12. If we have a two-layer situation where V1 = 1950 m/s and V2 = 3900 m/s (P-wave
velocities), what will the P-wave critical angle be?
 c = sin-1(1950/3900) = 30°
13. In this figure, what will be observed that will help locate the salt body?
 early arrival times (time

leads) for rays passing
through salt (due to salt’s
higher velocity)
14. In a gravity survey, what observations must you acquire (or, what information do you
need) in order to be able to carry out a drift correction?
 several g readings at same (base) station and the times they were made (klokkeslett)
15. In a gravity survey, what observations do you have to acquire (or, what information do
you need) in order to be able to carry out the Bouguer correction?
 near-surface density and elevation (thickness of layer above reference level)
16. If you apply the free-air correction in a gravity survey, what does it correct for?
 elevation (only)
17. Name two different geological features or structures or rock types that you might be able
to map by carrying out a magnetic survey.
 basement structure; igneous intrusives; salt; metallic ore bodies; rocks rich in magnetite; etc.
18. Name one geological feature or occurrence that you might be able to find with resistivity
(electrical) prospecting, and indicate how or why.
 salt – high resistivity; metallic ore – low ; hydrocarbons – high ; sediment (low ) that is
intercalated in basalt (high )
19. What sort of data could this be and what process could have been applied to (a) to get (b)?
(a)
 gravity or magnetic; could

even be topography or
some electrical data;
 high-cut or low-pass filter,
or upward continuation
(smoothing: small
deduction of ¼ %)
(b)
20. You have a seismic line from a region where problems were caused by a great assortment
of structures (faults, folds, dipping boundaries, etc.) in the deep subsurface. What sort of
seismic process do you think you’ll need to apply?
 migration
21. What are the main differences between these two types of data?
(a) (b)
 resolution in (a) better in deeper section, resolution in (b) better in shallower section; time scales are
different (over 2:1) but apparently same depth range, indicating P and S (or PP and PS) sections
22. What do the letters CMP stand for? • common midpoint
23. A seismic wavelet, generated by an airgun, propagates in all directions through a layered
rock medium. What three (3) mechanisms will be active in decreasing the amplitude of
deep reflections that are recorded back at the surface?
 absorption (internal friction); geometric spreading (spherical divergence); partitioning
at boundaries (reflection and transmission)
24. You have a land-seismic line from a region where problems were caused by large
variations in the thickness of the near-surface weathered layer. What sort of seismic
process do you think you’ll need to apply?
 statics
25. What process was applied to (a) to get (b)?
(a) (b)
(a) (b)
 correlation (vibroseis correlation)

Solution Pet110 2014

Uploaded by

Copyright:

Available Formats

Solution Pet110 2014

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Solution Pet110 2014

Uploaded by

Copyright:

Available Formats

PART A: Short-answer questions (50%; each worth 2%)

 ts = 0.004 s -or- fs = 250 Hz

 as identical 3D surveys repeated at different times (i.e. with time lapses)

 acoustic impedance = density x P-wave velocity

11. Write down an equation that expresses Snell’s law.

 p = (sin)V = constant -or- (sin)V = (sin)V

 early arrival times (time

 near-surface density and elevation (thickness of layer above reference level)

 gravity or magnetic; could

25. What process was applied to (a) to get (b)?

You might also like