Cummins Qsk19 Series Diesel Engine Service Repair Manual PDF

Shop Manual
QSK19 Series
Engines
ProCarManuals.com
CopyrightR 1997 Bulletin No. 3666232

Cummins Engine Company, Inc. Printed 12/97
All rights reserved
Foreword
This manual contains complete rebuild procedures and specifications. Disassembly, cleaning, inspection, and as-
sembly instructions are included. A listing of accessory and component suppliers is located in Section M - Component
Manufacturers. Suppliers can be contacted directly for any information not covered in this manual.
Read and follow all safety instructions. Refer to the WARNING in the General Safety Instructions in Section i
- Introduction.
The repair procedures in this manual are based on the engine or component removed from chassis. Some rebuild
procedures require the use of special service tools. Make sure the correct tools are used as described in the procedures.
When a specific brand name, number, or special tool is referenced in this manual, an equivalent product can be used
in place of the recommended item.
A series of specific service manuals (for example: Troubleshooting and Repair, Specifications, and Alternative Repair)
are available and can be ordered by filling out and mailing the Literature Order Form located in Section L - Service
Literature.
Cummins Engine Company, Inc. encourages the user of this manual to report errors, omissions, and recommendations
for improvement. Please use the postage paid, pre-addressed Literature Survey Form in the back of this manual for
communicating your comments.
The specifications and rebuild information in this manual is based on the information in effect at the time of printing.
Cummins Engine Company, Inc. reserves the right to make any changes at any time without obligation. If differences
are found between your engine and the information in this manual, contact a Cummins Authorized Repair Location
or call 1-800-DIESELS (1-800-343-7357).
ProCarManuals.com
The latest technology and the highest quality components are used to manufacture Cummins engines. When re-
placement parts are needed, we recommend using only genuine Cummins or ReConT exchange parts. These parts
can be identified by the following trademarks:
g-01 (shop-frwd)
Table of Contents
Section
Introduction ........................................................................................................................................ i
Engine Identification .......................................................................................................................... E
Complete Engine – Group 00 ............................................................................................................. 0
Cylinder Block – Group 01 ................................................................................................................. 1
Cylinder Head – Group 02 .................................................................................................................. 2
Rocker Levers – Group 03 .................................................................................................................. 3
Cam Followers/Tappets – Group 04 ................................................................................................... 4
Fuel System – Group 05 ..................................................................................................................... 5
Injectors and Fuel Lines – Group 06 ................................................................................................. 6

ProCarManuals.com
Lubricating Oil System – Group 07 .................................................................................................... 7
Cooling System – Group 08 ............................................................................................................... 8
Drive Units – Group 09 ....................................................................................................................... 9
Air Intake System – Group 10 ............................................................................................................ 10
Exhaust System – Group 11 ............................................................................................................... 11
Compressed Air System – Group 12 ................................................................................................. 12
Electrical Equipment – Group 13 ....................................................................................................... 13
Engine Testing – Group 14 ................................................................................................................. 14
Mounting Adaptations – Group 16 ..................................................................................................... 16
Electronic Engine Controls – Group 19 ............................................................................................. 19
Service Literature ............................................................................................................................... L
Component Manufacturers ................................................................................................................. M
Specifications ..................................................................................................................................... V
Index ................................................................................................................................................... X
QSK19
Section i - Introduction Page i-a
Section i - Introduction
Section Contents
Page
About the Manual ............................................................................................................................................. i-1
General Cleaning Instructions.......................................................................................................................... i-9
Glass or Plastic Bead Cleaning ..................................................................................................................... i-9
Solvent and Acid Cleaning ............................................................................................................................ i-9
Steam Cleaning ............................................................................................................................................ i-9
General Repair Instructions.............................................................................................................................. i-8
Welding on a Vehicle with Electronic Components ......................................................................................... i-8
General Safety Instructions.............................................................................................................................. i-7
Important Safety Notice ................................................................................................................................. i-7
How to Use the Manual..................................................................................................................................... i-1
Illustrations ....................................................................................................................................................... i-6
Symbols ............................................................................................................................................................ i-2
ProCarManuals.com
QSK19 About the Manual
Section i - Introduction Page i-1
About the Manual

This manual contains information needed to correctly operate and maintain your engine as recommended by Cummins
Engine Company, Inc. Additional service literature (Shop Manual, Troubleshooting and Repair Manual, etc.) can be
ordered by filling out and mailing the Literature Order Form located in Service Literature, Section L.
This manual does not cover vehicle or equipment maintenance procedures. Consult the vehicle or equipment
manufacturer for specific maintenance recommendations.
Both metric and U.S. customary values are listed in this manual. The metric value is listed first, followed by the U.S.
customary in brackets.
Numerous illustrations and symbols are used to aid in understanding the meaning of the text. Refer to page i-3 through
i-6 for a complete listing of symbols and their definitions.
Each section is preceded by a Section Contents to aid in locating information more quickly.
How to Use the Manual
This manual is organized according to the maintenance intervals that are to be performed. A table that states the
required intervals and the checks to be made is located in Section 2. Locate the maintenance interval that you are
performing and follow all the procedure steps given in that section. In addition, all the previous maintenance interval
procedures must also be performed.
Keep a record of all the checks and inspections made. A record form for recording date, mileage/kilometer or hours,
and what maintenance checks were performed is located in Section 2.
Refer to Section T for a troubleshooting guide to your engine. Follow the Troubleshooting Section Contents for locating
and correcting engine problems.
ProCarManuals.com
Refer to Section V for specifications recommended by Cummins Engine Company, Inc. for your engine. Specifications
and torque values for each engine system are given in that section.
NOTE: Discharge of oil or oily water into or upon the water is a direct violation of today’s laws. Violators are subject
to a penalty of various monetary charges. Dispose of these substances in accordance with standards set by the EPA.
Symbols QSK19
Page i-2 Section i - Introduction
Symbols
The following symbols have been used in this manual to help communicate the intent of the instructions. When one
of the symbols appears, it conveys the meaning defined below:
ProCarManuals.com
g-01 (full-sym)
QSK19 Symbols
ProCarManuals.com
Symbols QSK19
ProCarManuals.com
QSK19 Symbols
ProCarManuals.com
Illustrations QSK19
Illustrations
Some of the illustrations throughout this manual are ge-
neric and will not look exactly like the engine or parts used
in your application. The illustrations can contain symbols
to indicate an action required and an acceptable or not
acceptable condition.
The illustrations are intended to show repair or replace-

ment procedures. The procedure will be the same for all
applications, although the illustration can differ.
ProCarManuals.com
g-01 (illus)
QSK19 General Safety Instructions
General Safety Instructions

Important Safety Notice
WARNING
Improper practices or carelessness can cause burns, cuts, mutilation, asphyxiation or other bodily injury or
death.
Read and understand all of the safety precautions and warnings before performing any repair. This list contains the
general safety precautions that must be followed to provide personal safety. Special safety precautions are included
in the procedures when they apply.
• Make sure the work area surrounding the product is dry, well lit, ventilated, free from clutter, loose tools, parts,
ignition sources and hazardous substances. Be aware of hazardous conditions that can exist.
• Always wear protective glasses and protective shoes when working.
• Rotating parts can cause cuts, mutilation or strangulation.
• Do not wear loose-fitting or torn clothing. Remove all jewelry when working.
• Disconnect the battery (negative [-] cable first) and discharge any capacitors before beginning any repair work.
Disconnect the air starting motor if equipped to prevent accidental engine starting. Put a ‘‘Do Not Operate’’ tag
in the operator’s compartment or on the controls.
• Use ONLY the proper engine barring techniques for manually rotating the engine. Do not attempt to rotate the
crankshaft by pulling or prying on the fan. This practice can cause serious personal injury, property damage,
or damage to the fan blade(s) causing premature fan failure.
• If an engine has been operating and the coolant is hot, allow the engine to cool before you slowly loosen the
filler cap and relieve the pressure from the cooling system.
ProCarManuals.com
• Do not work on anything that is supported ONLY by lifting jacks or a hoist. Always use blocks or proper stands
to support the product before performing any service work.
• Relieve all pressure in the air, oil, fuel and the cooling systems before any lines, fittings, or related items are
removed or disconnected. Be alert for possible pressure when disconnecting any device from a system that
utilizes pressure. Do not check for pressure leaks with your hand. High pressure oil or fuel can cause personal
injury.
• To prevent suffocation and frostbite, wear protective clothing and ONLY disconnect fuel and liquid refrigerant
(freon) lines in a well ventilated area. To protect the environment, liquid refrigerant systems must be properly
emptied and filled using equipment that prevents the release of refrigerant gas (fluorocarbons) into the atmo-
sphere. Federal law requires capturing and recycling refrigerant.
• To avoid personal injury, use a hoist or get assistance when lifting components that weigh 23 kg [50 lb] or more.
Make sure all lifting devices such as chains, hooks, or slings are in good condition and are of the correct capacity.
Make sure hooks are positioned correctly. Always use a spreader bar when necessary. The lifting hooks must
not be side-loaded.
• Corrosion inhibitor, a component of SCA and lubricating oil, contains alkali. Do not get the substance in your
eyes. Avoid prolonged or repeated contact with skin. Do not swallow internally. In case of contact, immediately
wash skin with soap and water. In case of contact, immediately flood eyes with large amounts of water for a
minimum of 15 minutes. IMMEDIATELY CALL A PHYSICIAN. KEEP OUT OF REACH OF CHILDREN.
• Naptha and Methyl Ethyl Ketone (MEK) are flammable materials and must be used with caution. Follow the
manufacturer’s instructions to provide complete safety when using these materials. KEEP OUT OF REACH OF
CHILDREN.
• To avoid burns, be alert for hot parts on products that have just been turned off, and hot fluids in lines, tubes,
and compartments.
• Always use tools that are in good condition. Make sure you understand how to use them before performing any
service work. Use ONLY genuine Cummins or Cummins ReConT replacement parts.
• Always use the same fastener part number (or equivalent) when replacing fasteners. Do not use a fastener of
lesser quality if replacements are necessary.
• Do not perform any repair when fatigued or after consuming alcohol or drugs that can impair your functioning.
• Some state and federal agencies in the United States of America have determined that used engine oil can be
carcinogenic and can cause reproductive toxicity. Avoid inhalation of vapors, ingestion, and prolonged contact
with used engine oil.
g-02 (safety)
General Repair Instructions QSK19
General Repair Instructions

This engine incorporates the latest technology at the time it was manufactured; yet, it is designed to be repaired using
normal repair practices performed to quality standards.
• Cummins Engine Company, Inc. does not recommend or authorize any modifications or repairs to engines
or components except for those detailed in Cummins Service Information. In particular, unauthorized
repair to safety-related components can cause personal injury or death. Below is a partial listing of
components classified as safety-related:
Air Compressor Flywheel Mounting Capscrews

Air Controls Fuel Shutoff Assemblies
Air Shutoff Assemblies Fuel Supply Tubes
Balance Weights Lifting Brackets
Cooling Fan Throttle Controls
Fan Hub Assembly Turbocharger Compressor Casing
Fan Mounting Bracket(s) Turbocharger Oil Drain Line(s)
Fan Mounting Capscrews Turbocharger Oil Supply Line(s)
Fan Hub Spindle Turbocharger Turbine Casing
Flywheel Vibration Damper Mounting Capscrews
Flywheel Crankshaft Adapter
• Follow all safety instructions noted in the procedures

— Follow the manufacturer’s recommendations for cleaning solvents and other substances used during the
ProCarManuals.com
repair of the engine. Some solvents and used engine oil have been identified by government agencies as
toxic or carcinogenic. Avoid excessive breathing, injestion and contact with such substances. Always use
good safety practices with tools and equipment.
• Provide a clean environment and follow the cleaning instructions specified in the procedures
— The engine and its components must be kept clean during any repair. Contamination of the engine or
components will cause premature wear.
• Perform the inspections specified in the procedures
• Replace all components or assemblies which are damaged or worn beyond the specifications
• Use genuine Cummins new or ReConT service parts and assemblies
— The assembly instructions have been written to use again as many components and assemblies as possible.
When it is necessary to replace a component or assembly, the procedure is based on the use of new
Cummins or Cummins ReConT components. All of the repair services described in this manual are available
from all Cummins Distributors and most Dealer locations.
• Follow the specified disassembly and assembly procedures to avoid damage to the components
Complete rebuild instructions are available in the shop manual which can be ordered or purchased from a Cummins
Authorized Repair Location. Refer to Section L — Service Literature for ordering instructions.
Welding on a Vehicle with Electronic Components
CAUTION
Improper welding can destroy the vehicle’s electronic components. Before welding, disconnect the negative
(-) and then positive (+) battery cables. Attach the welder ground cable within 0.61 meters [2 feet] of the part
being welded. Do NOT connect the welder ground cable to any electronic component or component mounting
location. Do NOT weld on the engine or engine-mounted components.
g-03 (repair-e)
QSK19 General Cleaning Instructions
General Cleaning Instructions

Solvent and Acid Cleaning
Several solvent and acid-type cleaners can be used to clean the engine parts. Experience has shown that the best
results can be obtained using a cleaner that can be heated to 90 to 95 degrees Celsius [180 to 200 degrees Fahrenheit].
A cleaning tank that provides a constant mixing and filtering of the cleaning solution will give the best results. Cummins
Engine Company, Inc. does not recommend any specific cleaners. Always follow the cleaner manufacturer’s
instructions.
Remove all the gasket material, o-rings, and the deposits of sludge, carbon, etc., with a wire brush or scraper before
putting the parts in a cleaning tank. Be careful not to damage any gasket surfaces. When possible, steam clean the
parts before putting them in the cleaning tank.
WARNING
Acid is extremely dangerous and can damage the machinery. Always provide a tank of strong soda water as a
neutralizing agent.
Rinse all of the parts in hot water after cleaning. Dry completely with compressed air. Blow the rinse water from all of
the capscrew holes and the oil drillings.
If the parts are not to be used immediately after cleaning, dip them in a suitable rustproofing compound. The
rustproofing compound must be removed from the parts before installation on the engine.
Steam Cleaning
Steam cleaning can be used to remove all types of dirt that can contaminate the cleaning tank. It is a good way to clean
the oil drillings.
ProCarManuals.com
WARNING
Wear protective clothing to prevent personal injury from the high pressure and extreme heat.
Do not steam clean the following parts:
1. Electrical Components 5. Belts and Hoses
2. Wiring 6. Bearings
3. Injectors 7. Electronic Control Module (ECM)
4. Fuel Pump 8. ECM Connectors
Glass or Plastic Bead Cleaning

Glass or plastic bead cleaning can be used on many engine components to remove carbon deposits. The cleaning
process is controlled by the size of the glass or plastic beads, the operating pressure, and the cleaning time.
CAUTION
Do not use glass or plastic bead cleaning on aluminum piston skirts. Do not use glass bead cleaning on
aluminum ring grooves. Small particles of glass or plastic will embed in the aluminum and result in premature
wear. Valves, turbocharger shafts, etc., can also be damaged. Follow the cleaning directions listed in the
procedures.
NOTE: Plastic bead blasting media, Part No. 3822735, can be used to clean aluminum ring grooves. Do not use any
bead blasting media on pin bores or aluminum skirts.
Follow the equipment manufacturer’s cleaning instructions. The following guidelines can be used to adapt to manu-
facturer’s instructions:
1. Bead size: - Use U.S. size No. 16-20 for piston cleaning with plastic bead media, Part No. 3822735.
- Use U.S. size No. 70 for piston domes with glass media.
- Use U.S. size No. 60 for general purpose cleaning with glass media.
2. Operating Pressure: - Glass: Use 620 kPa [90 psi] for general purpose cleaning.
- Plastic: Use 270 kPa [40 psi] for piston cleaning.
3. Steam clean or wash the parts with solvent to remove all of the foreign material and glass or plastic beads after
cleaning. Rinse with hot water. Dry with compressed air.
4. Do not contaminate the wash tanks with glass or plastic beads.
g-01 (clean-e)
General Cleaning Instructions QSK19
NOTES
ProCarManuals.com
QSK19
Section E - Engine Identification Page E-a
Section E - Engine Identification

Section Contents
Page
Engine Diagrams ............................................................................................................................................. E-6
Engine Views ............................................................................................................................................... E-6
Engine Identification ....................................................................................................................................... E-1
Cummins Engine Nomenclature ................................................................................................................... E-1
ECM Dataplate ............................................................................................................................................ E-1
Engine Dataplate ......................................................................................................................................... E-1
Specifications.................................................................................................................................................. E-2
Air Intake System ......................................................................................................................................... E-2
Batteries (Specific Gravity) ............................................................................................................................ E-5
Cooling System ........................................................................................................................................... E-4
Electrical System ......................................................................................................................................... E-2
Exhaust System ........................................................................................................................................... E-4
Fuel System ................................................................................................................................................. E-2
General Specifications ................................................................................................................................. E-2
Lubricating Oil System ................................................................................................................................. E-3
ProCarManuals.com
QSK19 Engine Identification
Section E - Engine Identification Page E-1
Engine Identification
Cummins Engine Nomenclature
The model name provides identification data for the engine.
Refer to the illustration for the model name identification.
The application codes are:
A = Agricultural
C = Construction
D = Generator Drive
F = Fire Pump
G = Generator Set
L = Locomotive
M = Marine
P = Power Unit
R = Railcar
T = Tactical Military
Engine Dataplate
ProCarManuals.com
The engine dataplate shows specific information about the

engine. The engine serial number (ESN) (1), Control Parts
List (CPL) (2), Model (3), and Horsepower and rpm rating
(4) provide information for ordering parts and service needs.
NOTE: The engine dataplate must not be changed unless
approved by Cummins Engine Company, Inc.
ECM Dataplate
The external ECM dataplate is located on top on the ECM.
The dataplate contains the following:
• ECM part number (P/N)
• ECM serial number (S/N)
• Manufacturer date code (D/C)
• Engine serial number (ESN)
• ECM code identifying the software in the ECM
Specifications QSK19
Page E-2 Section E - Engine Identification
Specifications
General Specifications
NOTE: For performance and fuel rate values, refer to the engine data sheet, or the fuel pump code for the particular
model involved.
Engine Speed ................................................... Refer to the fuel pump calibration data for optional speed rating.
Displacement ....................................................................................................................... 19 liters [1150 C.I.D.]
Bore and Stroke ................................................................................. 158.75 mm x 158.75 mm [6.25 in x 6.25 in]
Engine Weight:
Dry ........................................................................................................................................ 1720 kg [3800 lb]
Wet ........................................................................................................................................ 2045 kg [4504 lb]
Firing Order ......................................................................................................................................... 1-5-3-6-2-4
Valve and injector settings:
Intake valve adjustment ....................................................................................................... 0.36 mm [0.014 in]
Intake valve limits ........................................................................................ 0.28 to 0.43 mm [0.011 to 0.017 in]
Exhaust valve adjustment .................................................................................................... 0.81 mm [0.032 in]
Exhaust valve limits ................................................................................... 0.74 to 0.89 mm [0.029 to 0.035 in]
Injector OBC Method adjustment (in engine) ........................................................................ 19 N•m [165 in-lb]
Compression Ratio:
525 HP to 600 HP-Jacket Water Aftercooled (JWAC) ............................................................................... 17.0:1
600 HP to 750 HP-Low Temperature Aftercooled (LTA) ............................................................................. 15.0:1
ProCarManuals.com
Crankshaft Rotation (Viewed from the front of the engine) ..................................................................... Clockwise
Air Intake System
Maximum Allowable Intake Restriction (at rated speed and load)
• With Clean Filter Element ....................................................................................... 380 mm H2O [15 in H2O]
• With Dirty Filter Element ......................................................................................... 635 mm H2O [25 in H2O]
Electrical System
Maximum Starting Circuit Resistance
24 - volt starter .......................................................................................................................... 0.00200 Ohms
Battery Cable Sizes - American Wire Gauge (Maximum length in cranking motor circuit)
24 to 32 - volt
No. 00 ........................................................................................................................................... 6.1 m [20 ft]
No. 000 ......................................................................................................................................... 8.2 m [27 ft]
No. 0000 or two No. 0* ................................................................................................................ 10.7 m [35 ft]
Two No. 00 .................................................................................................................................. 13.7 m [45 ft]
Minimum Cranking Speed Without Starting Aid ....................................................................................... 150 rpm
* Two strands of No. 0 cable can be used instead of one No. 0000 cable, providing all connections are carefully made
to provide equal current flow in each parallel cable.
NOTE: Starting aids, such as block heaters, lubricating oil pan heaters, etc., are available to aid in cold weather starting.
System Voltage Ambient Temperatures

-18°C (0°F) 0°C (32°F)
Cold Cranking Reserve Capacity* Cold Cranking Reserve Capacity*
Amperes Amperes Amperes Amperes
24 Volt** 900 320 640 240
* The number of plates within a given battery size determines reserve capacity. Reserve capacity is the length of time
sustained cranking can occur.
** CCA ratings are based on two 12-volt batteries in series.
Fuel System
QSK19 Specifications
NOTE: For performance and fuel rate values, refer to the engine data sheet, or the fuel pump code for the particular
rating involved.
Basic Application Requirements
Engine Idle Speed ...................................................................................................................... 600 to 1400 rpm
Fuel Inlet Maximum Restriction:
• Clean Fuel Filter ......................................................................................................... 100 mm Hg [4.0 in-Hg]
• Dirty Fuel Filter .......................................................................................................... 203 mm Hg [8.0 in-Hg]
Fuel Drain Line Restriction:
• With Check Valves ...................................................................................................... 0 to 21 kPa [0 to 3 psi]
• With Check Valves Removed* .................................................................................. 14 to 34 kPa [2 to 5 psi]
*All QSK19 engines are built with a check valve.
Fuel Check Valve Between Fuel Pump and Cylinder Head (Integral to Fuel Pump):
• Opening Pressure ..................................................................................................... 21 to 35 kPa [3 to 5 psi]
Engine Minimum Cranking Speed ........................................................................................................... 150 rpm
Fuel Check Valve in Fuel Drain Line:
• Opening Pressure ......................................................................................... 13 to 25 mm Hg [1/4 to 1/2 psi]
Derate Engine Fuel Rate for High Altitude ................................. 4% per 300 m [1000 ft] above 3600 m [12,000 ft]
Derate Engine Fuel Rate for Hot Weather ......................... 2% per 11°C above 38°C [1% per 10°F above 100°F]
Shutoff Valve Solenoid Coil Resistance in Ohms 24VDC ............................................................... 28 to 32 Ohms
ProCarManuals.com
Fuel Pump Cranking Pressure - Minimum: ................................................................ 172 kPa [25 psi] @ 150 rpm
Fuel Pump Pressure - Minimum:
• 1500 rpm: ......................................................................................................................... 1448 kPa [210 psi]
• 1800 rpm: ......................................................................................................................... 1655 kPa [240 psi]
• 2100 rpm: .......................................................................................................................... 1861 kPa [270 psi]
• 2350 rpm: ......................................................................................................................... 1999 kPa [290 psi]
Fuel Filter Specifications (Cummins Engine Company, Inc. Standard No. 14,223)
Efficiency: ......................................................................................................................... 98.7% at 10 microns
96.0% at 8 microns
86.0% at 5 microns
Water Removal: ............................................................................................................................ Free = 95%
Emulsified = 95%
Lubricating Oil System
Oil Pressure (With 15W-40 Oil at 107° C [225° F])
At Idle (Minimum Allowable) .................................................................................................... 138 kPa [20 psi]
At No Load Governed Speed ............................................................................... 345 to 483 kPa [50 to 70 psi]
Oil Temperature
Maximum ................................................................................................................................. 120°C [250° F]
Oil Filter Capacity
Bypass Filter (Spin-On)(LF777 Fleetguard) ............................................................ 2.3 Liters [0.6 U.S. Gallons]
Full-Flow Filter (Spin-On)(LF670 Fleetguard) .......................................................... 2.7 Liters [0.7 U.S. Gallons]
Combination Filter (Two LF3000 Fleetguard) .......................................................... 5.7 Liters [1.5 U.S. Gallons]
Oil Pan Capacity (Liters) [U.S. Gallons]
Oil Pan Part No. High Low High Low
3096460 72 64 19 17
3086096 61 49 16 13
3086097 61 49 16 13
3331695 61 49 16 13
3331568 114 102 30 27
NOTE: When the rear gear train option is specified, add 7.6 liters [2 U.S. gallons] to the oil pan capacity listed above.
Cooling System
Coolant Capacity (Engine Only) ............................................................................................................. 32.2 liters
[34 U.S. Quarts]
Standard Modulating Thermostat Range .............................................................. 82°C to 94°C [180°F to 202°F]
Standard LTA Thermostat Range .......................................................................... 69°C to 78°C [157°F to 172°F]
Maximum Coolant Pressure (Exclusive of Pressure Cap) ............................................................. 241 kPa [35 psi]
Maximum Allowable Top Tank Temperature ..................................................................................... 100°C [212°F]
Minimum Recommended Top Tank Temperature .............................................................................. 70°C [160°F]
Maximum Allowable Deaeration Time .................................................................................................. 25 Minutes
Minimum Allowable Drawdown or 20% of System Capacity (whichever is greater) .......... 11 liters [12 U.S. Quarts]
Minimum Allowable Pressure Cap ................................................................................................... 50 kPa [7 psi]
ProCarManuals.com
Exhaust System
Back Pressure - Maximum (at rated speed and load): ......................................................... 75 mm Hg [3.0 in Hg]
Exhaust Pipe Size (Normally Acceptable Inside Diameter):
• All Ratings ............................................................................................................................ 152 mm [6.0 in]
Batteries (Specific Gravity)

ProCarManuals.com
Engine Diagrams QSK19
Engine Diagrams
Engine Views
The illustrations show the locations of the major external engine components, the filters, and other service and
maintenance points. Some external components will be at different locations for different engine models.
ProCarManuals.com
1. Fuel Rail Quick-Disconnect Fitting A. Fan Hub

2. Timing Rail Quick-Disconnect Fitting B. Aftercooler Assembly
3. Oil Pressure Sensor (OPS) C. Combination Full Flow/
4. Intake Manifold Temperature Sensor (IMTS) Bypass Oil Filters
5. Intake Manifold Pressure Sensor (IMPS) D. Electronic Control
6. Engine Speed Sensor (ESS)(Generator Drive) Module (ECM)
7. Ambient Air Pressure Sensor (AAPS) E. Dipstick
8. Fuel Pump Outlet Quick-Disconnect Fitting F. Fuel Filters
9. Engine Speed Sensor (NOT Generator Drive) G. Control Valve Body
10. Coolant Temperature Sensor (CTS) H. Air Compressor
11. OEM Interface Harness I. Fuel Pump
12. Engine Harness
QSK19 Engine Diagrams
ProCarManuals.com
EXHAUST SIDE - QSK19
1. Coolant Outlet A. Turbocharger

2. Coolant Inlet B. Thermostat Housing
3. Alternate Location for Engine C. Fan Idler and Assembly
Speed Sensor (ESS)(G-Drive ONLY) D. Coolant Filter
4. Coolant Supply to Turbocharger E. Starting Motor
5. Turbocharger Oil Drain
6. Oil Inlet to Turbocharger F. Flywheel Housing
G. Oil Cooler
Engine Diagrams QSK19
NOTES
ProCarManuals.com
QSK19
Section 0 - Complete Engine - Group 00 Page 0-a
Section 0 - Complete Engine - Group 00

Section Contents
Page
Engine Assembly ........................................................................................................................................... 0-58
Assemble ................................................................................................................................................... 0-58
Engine Disassembly ........................................................................................................................................ 0-8
Disassemble ................................................................................................................................................ 0-9
General Information ...................................................................................................................................... 0-8
Assembly .............................................................................................................................................. 0-8
Disassembly.......................................................................................................................................... 0-8
Service Tools ................................................................................................................................................... 0-1
Engine Disassembly and Assembly ............................................................................................................... 0-1
ProCarManuals.com
QSK19 Service Tools
Section 0 - Complete Engine - Group 00 Page 0-1
Service Tools
Engine Disassembly and Assembly
The following special tools are recommended to perform procedures in this section. The use of these
tools is shown in the appropriate procedure. These tools can be purchased from your local Cummins
Authorized Repair Location.
Tool No. Tool Description Tool Illustration

Engine Support Bracket Kit
Support the front of the engine to allow the front support or oil pan
adapter to be removed.
3375252
ProCarManuals.com
Depth Gauge Assembly

Measure cylinder liner protrusion and cylinder liner counterbore
ledge angle.
3823495
Puller
Remove the alternator and accessory drive pulleys.
ST-647
Main Bearing Cap Pulley

Used to remove the main bearing caps from the cylinder block.
ST-1178
Drill Ream Fixture

Machine dowel hole to install oversize dowels in cylinder block
and flywheel housing. Use with a drill, reamer, and the appro-
ST-1232
priate drill/ream bushing set.
Piston Ring Expander

Designed to install piston rings on the piston without damaging
or distorting the rings.
ST-1269
Service Tools QSK19
Page 0-2 Section 0 - Complete Engine - Group 00

Connecting Rod Guide Pins
Special nylon pins used to protect the crankshaft journal by
guiding the connecting rod during installation or removal.
3375098
Liner Installation Tool

Install cylinder liner in engine.
3375422
Crack Detection Kit

Check for cracks in any engine component. Contains cleaner,
developer, and penetrant.
3375432
ProCarManuals.com
Injection Timing Tool

Check injection timing. The timing fixture is designed to deter-
mine the push tube travel in relation to the piston travel.
3824942
Universal Injector Timing Tool Fixture Kit Update

Up-Date Kit for the previous Universal Injection Timing Tool,
3823451, to include QSK 19 hardware.
3824946
Light Duty Puller Kit

Remove small bushings, oil seals, and bearings.
3375784
Puller Assembly
Remove the crankshaft front gear from the crankshaft. Use with
Part No. 3375835 Puller Jaw.
3375834
Universal Liner Puller

Remove cylinder liner from engine.
3376015
QSK19 Service Tools

Pulley Installation Tool
Install the alternator and accessory drive pulleys.
3376326
Cummins Sealant
Used to prevent coolant or oil leaks. This is one part Room
Temperature Vulcanizing (RTV) silicone rubber, adhesive, and
3823494
sealant material having high heat and oil resistance, and low
compression rate.
Camshaft Bushing Tool Hydraulic Actuator Kit

Hydraulic ram provides the force to install/remove cam bushings
when used with installation/removal kit.
3823621
ProCarManuals.com
Camshaft Bushing Installation/Removal Kit

Used with the Part No. 3823621 Camshaft Bushing Hydraulic
Actuator Kit to remove the camshaft bushing.
3824863
Camshaft Pilot
Install camshaft without damaging the camshaft bushings or
camshaft.
3825150
Camshaft Gear Puller Kit

Remove camshaft gear from camshaft without removing cam-
shaft from engine.
3824900
Main Bearing Roll-out Tool

Used to remove and install main bearing shell.
3823818
Torque Wrench Adapter

Secures the rocker lever adjusting screw while tightening the lock
nut.
ST-669
Service Tools QSK19

Water Tube Driver
Used to install or remove the water transfer tubes from the rocker
housings.
ST-1319
Torque Wrench
A dial-type torque wrench used to accurately adjust injectors in
inch-pounds. Use of a clicker-type torque wrench is not recom-
3824783
mended. 0-35 N•m [0-300 in-lb]

Used to remove small bushings, oil seals, and bearings.
3375784
ProCarManuals.com
Torque Wrench
Inch-pound torque wrench used to tighten the valve lever ad-
justing screw. Does not require screwdriver attachment.
3376592
Valve Setting Gauge Kit

Kit contains two 25.4 mm [1 in] wide feeler gauges for centering
under the swivel foot of the rocker lever when setting the valves.
3824901
The kit contains an intake valve gauge at 0.36 mm [0.014 in] and
an exhaust valve gauge at 0.081 mm [0.032 in].
Fuel Pump/Air Compressor Wrench

Used to reach nuts when removing or installing the fuel pump or
air compressor.
3376845
Filter Wrench
Remove spin-on filter.
3375049
Injector Removal / Installation Tool

Used to remove and install the QSK injector.
3823580
3824830
QSK19 Service Tools

Torque Wrench
This is a [3/8 inch] drive, [300 in-lb], torque wrench used to set
injector preload adjustments on engines with the high pressure
3824783
fuel injection systems such as the QUANTUM™ Series K19.
Pressure Regulator Removal Tool

Remove retaining ring from lubricating oil pump regulator (on
engine).
3375055
Filter Cutter
Open spin-on full-flow filter for inspection.
3376579
ProCarManuals.com
Thermostat Seal Mandrel

Install the thermostat seal in the thermostat housing.
ST-1225
Belt Tension Gauge

Measure the accessory drive belt tension.
ST-1293
Coupling Puller
Used to remove accessory drive coupling and spline coupling
hub.
3376663
Oil Seal Remover/Installer

3824760
Dial depth gauge

This gauge is used to check for proper nozzle ring crush or end
clearance checks on turbochargers.
ST-537
Service Tools QSK19

O-Ring Pick
Use to remove and install o-rings.
3376399
Lubricating Oil Sampling Filter

Used to monitor oil contamination.
ST-1135
Dowel Pin Extractor

Remove dowel pins.
ST-1134
ProCarManuals.com
Drill Ream Fixture

ST-1232 priate drill/ream bushing set.
Digital Volt-Ohm Meter

Measure electrical circuits; voltage (volts), resistance (ohms),
and current (amps).
3377161
Weather-Pack Terminal Removal Tool

Used to repair Weather-Pack connectors.
3822608
Engine Position Sensor Installation Tool

Used to remove and install the engine position sensor.
3822747
Deutsch Terminal Removal Tool

Used to repair Deutsch connectors.
3822760
QSK19 Service Tools

Heat Gun
Used to repair connector wires.
3822860
Wiring Repair Kit

Contains a variety of connectors, pins, seals, terminals, test leads,
and other tools used to repair connectors.
3822926
Wire Crimping Pliers

Used when repairing connector wires.
3284903
ProCarManuals.com
Lubricant DS-ES
Dielectric lithium grease used to lubricate the pins in the elec-
trical connectors before installation.
3822934
Deep Well Socket (1–1/4 inch)

Used to remove and install sensors and actuators.
3823843
Electrical Contact Cleaner

A non-petroleum cleaner used to clean electrical contacts and
connectors.
3824510
Engine Disassembly (000-003) QSK19
Engine Disassembly (000-003)

General Information
General Information
These procedures apply to all QSK19 engines. The differences between engine model due to the application, the
optional equipment on an engine, and the year an engine was built are included in the instructions. Omit the steps
that do not apply to the engine being rebuilt.
WARNING
A Warning statement is included for any component or assembly that weighs more than 23 kg [50 lb]. To avoid
personal injury, use a hoist or get assistance from more than one person when removing or installing these parts.
CAUTION
All fasteners are given in U.S. Customary measurements. All fasteners have right-handed threads unless a
Caution states that a fastener has left-handed threads.
Disassembly
The instructions in this procedure are organized in a logical sequence to disassemble an engine. This is not the only
sequence to disassemble an engine. Certain parts must be removed in the sequence indicated. Use this sequence
until you become familiar with the engine.
Discard all gaskets, seals, hoses, filters, and o-rings. Keep these parts if they are needed for a failure analysis.
Label, tag, or mark the parts for location as the parts are removed. This will help find all the parts that can be involved
ProCarManuals.com
in a failure, and simplify the assembly procedure.

Label, tag, or mark the wiring harness and all components and sensors as they are removed from the engine.
Label, tag, mark, or photograph all special equipment prior to removal from an engine. This engine assembly procedure
does not include the installation of special optional equipment.
Force must be used to remove certain parts. A mallet must be used when force is required.
Avoid as much dirt as possible during disassembly. The accumulation of additional dirt will make it more difficult to
clean the components.
Assembly
This procedure assumes that all of the components and assemblies have been cleaned, replaced, or rebuilt and are
ready to be installed on the engine.
Torque values are listed in each step. If a torque value is not specified, use the chart listed in the Specifications (Section
V) to determine the correct torque value.
Many of the gaskets and o-rings are manufactured from a material designed to absorb oil. These gaskets will enlarge
and provide a tight seal after coming in contact with oil. Use ONLY a recommended contact adhesive or a vegetable
based oil to install these parts.
If the capscrew length is not specified, use the formula in the Specifications (Section V) to determine the correct
capscrew length. The use of a longer capscrew than the capscrew that is listed can result in damage to the engine.
QSK19 Engine Disassembly (000-003)
Disassemble
Remove the Water Filter
Open the draincock on the oil cooler housing and on the
water pump.
Remove and discard the coolant filter.
Prepare Engine to be Mounted on Rebuild Stand

WARNING
When using steam, wear protective clothing and safety
glasses or a face shield. Hot steam can cause serious
personal injury.
CAUTION
Cover all engine openings and electrical components.
ProCarManuals.com
This will prevent water damage.

Use steam to clean the heavy dirt from the exterior of the
engine.
NOTE: Put a tag on all hoses, lines, linkage, and electrical

connections as they are removed to identify location and
aid during the installation process.
WARNING
Hot oil can cause serious personal injury. Drain the oil
when the oil temperature is approximately 60°C [140°F].
WARNING
Some State and Federal agencies in the United States
of America have determined that used engine oil can be
carcinogenic and can cause reproductive toxicity. Avoid
inhalation of vapors, ingestion, and prolonged contact
with used engine oil. Always use the proper procedures
to dispose of the oil.
Remove the oil drain plug from the bottom of the oil sump.
Drain the oil.
Install the drain plug.
Tighten the drain plug.
Torque Value: 100 N•m [75 ft-lb]
Remove the 28 capscrews.

Remove the oil pan.
Remove and discard the gasket.
ProCarManuals.com
Rail Applications
Remove the lubricating oil drain plug.
Drain the lubricating oil.
Replace the drain plug and tighten.
Rail Applications
Remove the lubricating oil filters and filter head.
Remove the fuel filter and filter head.
Remove the coolant filter and filter head.
Rail Applications
Remove 15 capscrews on the top of the oil pan.
Install two 3/8 - 16 guide studs in the capscrew holes.
ProCarManuals.com
Rail Applications
Remove the remaining 23 capscrews.
Remove the lubricating oil pan.
Remove the Fuel Filters

WARNING
Fuel is flammable. Do not allow cigarettes, flames,
sparks, arcing switches or equipment, pilot lights, or
other ignition sources near the fuel system.
Close the fuel line shutoff valve before changing the fuel
filters, or the overhead tank can drain, causing a fuel leak.
Remove the fuel filter with filter wrench, Part No. 3376807.
Remove the thread adapter sealing ring (1).

Use a clean, lint-free towel to clean the surface of the filter
head gasket.
Remove the Oil Filters

The external appearance of the full-flow (1) the bypass (2)
and the combination (3) filters are the same. The accom-
panying picture identifies the differences among the three
filters.
CAUTION
The bypass and combination filters both have the same
threads. Verify correct filter is used for replacement to
ProCarManuals.com
avoid damage to the engine.

NOTE: The full-flow filter contains [1 1/2-16 inch] threads.
The bypass and combination filters contain [2 1/4-12 inch]
threads.
A combination oil filter is used on most engines. The upper

section of the filter contains the full-flow filter element while
the lower section contain the bypass element.
NOTE: The following illustrations show the combination oil

filter. Use the same procedure when changing the remote
bypass oil filters.
Use an oil filter wrench, Part No. 3375049, or equivalent.
Remove the oil filters.
Discard the filters if they are not needed for a failure
analysis.
Remove the Cooling Fan Drive Belt

CAUTION
The fan belt idler is under tension. Do NOT allow your
hands to get between the idler and the belt, or the fan
hub. Personal injury can result.
Loosen nuts (1) and (2). Turn nut (1) counterclockwise to
end of threaded rod to relieve tension on the belt.
Remove the fan belt.

ProCarManuals.com
Check the belt for wear.

If the belt indicates any wear, it must be replaced.
Remove the Alternator Drive Belt

Loosen the adjusting link and the alternator mounting
capscrews.
NOTE: The lower jam nut has left-hand threads.
Loosen both of the jam nuts. Turn the adjusting screw to
relieve the belt tension.
Remove the belt.
Check the belt for wear.

If the belt indicates any wear, it must be replaced.
Remove the Alternator

WARNING
Always disconnect the negative (-) cable first to avoid
sparks that can ignite explosive battery gases.
WARNING
Batteries emit hydrogen gas. To avoid explosion and
personal injury, do not smoke or allow ignition source
ProCarManuals.com
in area when servicing batteries.

Disconnect the wiring and ground strap from the alternator.
Remove capscrews (1) and (2) and the adjusting link.

Remove capscrew (3) and nut.
Remove the alternator.
Remove the Belt Driven Fan Hub

CAUTION
This assembly weighs more than 23 kg [50 lb]. To avoid
personal injury, use a hoist or get personal assistance.
Remove the eight nuts and washers, and the fan hub.
Remove the Fan Drive Idler Arm Assembly

CAUTION
The belt tensioner and the pivot arm assembly will
rotate during removal. Personal injury can result. To
avoid personal injury, use a hoist or get personal as-
sistance to lift the component.
Remove the belt adjusting nut (1) from the tensioner as-
sembly.
Remove the three capscrews (2) from the pivot arm as-
sembly.
Remove the pivot arm and the belt tensioner as an
assembly.
Remove the belt tensioner from the idler arm assembly.

ProCarManuals.com
Remove the Coolant Tubes and Hoses - Conventional

Aftercooling
Remove the bypass tube clip (9).
Loosen both hose clamps.
Remove the bypass tube.
Remove the aftercooler coolant return tube aftercooler cool-

ant supply tube, gaskets and hoses from the thermostat
housing support.
Remove the aftercooler water supply tube clip (7). Loosen

the hose clamps. Remove the support bracket (34).
Remove the tube (31). Remove and discard the o-ring.
Remove the Coolant Tubes and Hoses - Low Tempera-

ture Aftercooling
Remove the bypass tube clamp (9).
Remove the bypass tube, hose, and water connection.
ProCarManuals.com
Remove the water inlet and outlet tube clips (7).

Loosen the hose clamps.
Remove the aftercooler water tube support bracket (34).
Remove the aftercooler water tubes.
Remove and discard the o-rings.
Disconnect the coolant temperature sensor wire (17).
Remove the aftercooler water supply tube clip (7).

Loosen the hose clamps.
Remove the support bracket (34).
Remove the tube (31).
Remove and discard the o-ring.
Remove the Turbocharger Coolant Supply and Return

Hoses
NOTE: This procedure applies to a turbocharger with a
water-cooled bearing housing.
Disconnect the coolant supply hose and the coolant return
hose from the turbocharger.
Remove the Crossover Connection

Remove the four mounting capscrews at the top of the air
crossover.
Loosen the four capscrews at the bottom of the air cross-
over until there is clearance between the washer and the
crossover.
Remove the air crossover hose clamps and slide the hose
down the turbocharger outlet.
ProCarManuals.com
Remove the air crossover.
Remove the Turbocharger

Remove the mounting capscrews, nuts, and the turbo-
charger.
Rail Applications
Remove the turbocharger drain line from the scavenge
cross and the turbocharger.
Loosen the hose clamp and remove the hose.
Rail Applications
Remove the 24 capscrews and intake manifold.
Remove the Exhaust Manifold

Use two [7/16-14x5 in] guide studs (12).
Remove two capscrews as shown.
Install the guide studs as shown.
ProCarManuals.com
CAUTION
personal injury, use a hoist or get assistance to lift the
component.
Remove the remaining capscrews.
Remove the exhaust manifold and the gaskets.
Discard the gaskets.
Marine Applications
NOTE: Do not rip, tear, or damage the insulation of the
exhaust manifolds.
Remove the 7 mounting capscrews.
Remove the heat shield.
The heat shield comes straight off the manifold.
OEM Interface Harness - General Information

The QSK equipped engines use three separate wiring har-
ness to control the engine and some of the vehicle opera-
tions.
1. Engine Harness
2. OEM Interface Harness
3. OEM Harness
Replace a harness if there is an open circuit or a short

circuit found under the protective covering of the harness
body.
ProCarManuals.com
OEM Wiring Harness - General Information

The OEM harness is supplied and installed by the vehicle
manufacturer. Follow the vehicle manufacturer’s instruc-
tions, if replacement is necessary. Refer to the vehicle
manufacturer’s troubleshooting and repair manual.
Remove the OEM Interface Harness

Disconnect the 21-pin and 31-pin connectors from the OEM
harness.
Disconnect the 2-pin and 6-pin Deutsch connectors.
Remove the 21-pin and 31-pin connectors from the harness

support brackets.
ProCarManuals.com
Use a 4 mm [5/32 in] hex head wrench to disconnect the

OEM interface harness Deutsch connector from the ECM.
Cut the six wire ties from the harness support bracket and
remove the OEM interface harness from the engine.
Remove the Engine Wiring Harness

Disconnect the engine harness from the coolant pressure
sensor.
Remove the engine harness clamps.
Cut the ties on the alternator bracket and front engine cover
bracket.
ProCarManuals.com
Disconnect the coolant temperature sensor and engine

position sensor.
Cut the ties on the thermostat housing bracket, aftercooler

tube, and fuel tube.
Disconnect the intake manifold temperature sensor and

intake manifold pressure sensor.
Cut the tie on the engine datalink connector bracket.

Remove the bracket.
Remove the clamp from the hose.
ProCarManuals.com
Disconnect the engine harness from the following:

1. Oil pressure sensor
2. Timing actuator
3. Rail actuator
4. Ambient air pressure sensor
5. Rail pressure sensor
6. Timing pressure sensor
Disconnect the fuel shutoff control wire to the fuel shutoff

solenoid.
Disconnect the engine block ground from the block.
Use a 4 mm [5/32 in] hex head wrench to disconnect the

engine harness Deutsch connector from the ECM.
ProCarManuals.com
Cut the seventeen ties holding the engine harness to the

support bracket.
Cut the corner tie holding the engine harness to the sup-
port bracket.
Remove two screws and C-clamps.
Remove the engine harness.
Remove the Water Pump Outlet Connection Assembly

Remove the water pump outlet connection assembly.
Remove the water transfer tube from the water connection.
Remove and discard the two o-rings (13) and the gasket.
Remove the Torque Converter Cooler Cover (if equipped)

Remove the oil supply (1) and oil return (2) hoses from the
torque converter cooler.
Remove the torque converter cooler cover mounting

capscrews.
NOTE: The cover must be pried from the housing because
of the tight fit between the cover and the o-rings on the
elements.
ProCarManuals.com
Remove the Oil Cooler Cover (if equipped)

Remove all of the capscrews, the oil cooler cover, and
gasket.
Discard the gasket.
Remove the Torque Converter Cooler Housing (if

equipped)
CAUTION
This component weighs 23 kg [50 lb] or more. To avoid
component.
Use two [3/8-16 x 12 in] guide studs to support the housing
while the capscrews are being removed.
Remove the remaining capscrews, the torque converter
cooler housing, and the gasket.
Discard the gasket.
Remove the torque converter cooler element mounting

nuts.
Remove the elements.
Remove and discard the o-rings.
Remove the Oil Cooler Elements

NOTE: There is little clearance between the capscrews and
the block on some engines. If necessary, use a drift and a
mallet to tap the loosened capscrews from the oil cooler
housing.
Remove the eight capscrews and the two oil cooler ele-
ments.
Remove and discard the gaskets.
ProCarManuals.com
Remove the Water Pump and Water Pump Drive Shaft

Remove the capscrew from the water pump support bracket.
Remove the three capscrews and the nut from the water
pump mounting flange.
Remove the water pump and gasket.
Discard the gasket.
Remove the drive shaft (14).
Remove the Starting Motor

Disconnect the electrical connections from the starting
motor.
CAUTION
Remove the starting motor capscrews, the starter, spacers,
and the gaskets.
NOTE: All engines do not contain spacers and gaskets.
Remove the Oil Filter Head

WARNING
with used engine oil. Always follow the proper proce-
dures to dispose the used oil.
ProCarManuals.com
Remove the six capscrews and the filter head assembly.

Lube Oil Transfer Connection Block

Remove the transfer connection block.
Remove the Oil Cooler Housing

Remove the capscrews and oil cooler housing.
Remove the Dipstick and Dipstick Tube (if equipped on

this side of engine)
Remove the dipstick and dipstick tube.
Remove the turbocharger oil supply and drain lines.

Disconnect the oil drain hose and the oil supply hose from
the turbocharger.
ProCarManuals.com
Remove the Alternator Drive Pulley

Remove the plastic plug at the end of the shaft.
Insert the adapter, Part No. 3376089, in the shaft to prevent
damage. The adapter is included with the pulley installation
tool, Part No. 3376326.
NOTE: If the adapter is not available, a [3/4-16 inch]
capscrew with a head ground smaller than the pulley I.D.
can be used.
Put the puller on the pulley.

Remove the pulley.
Remove the adapter.
Remove the Alternator Drive Oil Seal

Remove the six button hex head socket capscrews.
Use three [1/4-20 x 1 in] capscrews to remove the seal from

the alternator drive shaft.
Install the three capscrews in the clinch nuts in the seal
case.
Tighten the capscrews alternately and evenly to remove the
seal.
ProCarManuals.com
Remove the o-ring from the groove in the gear cover.
Remove the Water Pump Drive Assembly

Remove the water pump drive assembly.
NOTE: If necessary, tap on the end of the shaft with a
mallet.
Prepare the Engine Rebuild Stand

The following instructions apply to the Engine Roll over
Stand, Part No. 3375194. If another engine stand is used,
follow the manufacturer’s instructions.
Disengage the locking pin. Turn the swivel plate until the
word “TOP” can be seen as shown.
CAUTION
Six spacers, 20 mm [3/4 - in] thick are required to pre-
vent the engine form contacting the engine stand. Put
the spacers between the adapter plate and the engine
stand.
Use six 5/8-18x3-1/4 in Grade 5 capscrews, plain washers,
and locknuts.
ProCarManuals.com
Use the adapter plate, Part No. 3375596. Use the specified
mounting hardware to install the adapter plate.
NOTE: It will be necessary to rotate the swivel plate to
install all six of the capscrews.
Disengage the locking pin (16). Turn the adapter plate as

shown.
Install one 3/8-16x3-3/4 in capscrew in the location shown.
Put the Engine on the Rebuild Stand

Install engine lifting fixture, Part No. 3822512, to engine
lifting brackets.
WARNING
Engine weighs 2045 kg [4508 lb]. Use a properly rated
hoist and engine lifting fixture, Part No. 3822512, to lift
the engine.
Lift the engine.
WARNING
Be sure the locking pin on the engine stand is in the
“LOCKED” position before removing the lifting hoist.
Use nine 3/8-16x3-3/4 in Grade 5 capscrews, plain wash-
ers, and lockwashers.
Attach the capscrews through the holes as shown.
ProCarManuals.com

Remove the hoist and lifting fixture.
Remove the Oil Filler Cap and Hose

Remove oil filler cap from fill opening.
Remove cap, chain, washer and capscrew from engine.
Loosen the two hose clamps. Remove the hose.
Remove the Hand Hole Cover with Hose Adapter

Remove six capscrews, hand hole cover and gasket.
Discard gasket.
Remove the Aftercooler Assembly

Remove the coolant lines from the aftercooler assembly.
CAUTION
personal injury, use a hoist or get personal assistance
to lift the component.
Remove two mounting capscrews. Install two [3/8-16 in]
guide studs.
Use a hoist, two tee handles, and a lifting sling. Attach the
ProCarManuals.com
tee handles, sling, and hoist.

Raise the hoist until there is tension on the sling.
Remove the remaining capscrews and the aftercooler as-
sembly.
Remove and discard the aftercooler bolt seals from the

aftercooler housing.
Remove the Air Compressor Air Inlet Connection and

Fuel Supply Tubing
Loosen the two hose clamps and remove the inlet hose.
Remove the air compressor air inlet connection.
Remove and discard the hose.
Loosen the fuel tubing nuts at the fuel junction block on the
fuel manifold.
Remove the fuel tubing mounting clamp and the fuel tubes.
Remove the Fuel Manifold

Remove the 12 capscrews.
Remove the front fuel manifold.
Discard the o-rings.
Repeat this process for the removal of the rear fuel manifold.
Remove the ECM

Remove the six capscrews which hold the ECM to the
control valve body.
Remove the ECM from the control valve body.
ProCarManuals.com
Remove the Fuel Control Valve Body Assembly

Clean the control valve body and the surrounding area.
Disconnect the fuel supply hose (1).

Remove the four capscrews.

Remove the control valve body assembly.
Remove the Rocker Lever Covers

NOTE: Crankcase breathers can be mounted in any cyl-
inder location. Record the number of breathers and their
correct location before mounting.
Remove the rocker lever cover and discard the gasket.
ProCarManuals.com
Remove the Rocker Lever Assemblies

NOTE: Do not allow the rocker levers to fall off the shaft
during removal.
Remove the two capscrews.
Remove the rocker lever assemblies.
Remove the Push Rods and Crossheads

NOTE: It is a good service practice to mark the push rods
so they can be installed in their original position.
Remove the push rods and crossheads.
Remove the Injector and Clamp

NOTE: The hold-down clamp can not be removed until the
injector is removed.
Remove the injector hold-down capscrew.
Remove the injector and clamp.
Use injector puller, Part No. 3823579, to remove the injec-
tors. Insert the pin of the tool in the hole provided in the
body of the injector. The hole faces the front of the engine.
If the injector puller mentioned above is not available,
carefully use a pry bar. Pry upward on the injector against
the cylinder head.
Remove the Thermostat Housing Assembly (Conven-

tional)
Disconnect the air compressor water outlet tube from the
thermostat housing.
Remove the four mounting capscrews and the thermostat
housing assembly.
Remove the water transfer tube.
ProCarManuals.com
Remove and discard the two o-rings (19).
Remove the Thermostat Housing Assembly (LTA)

Remove the four mounting capscrews.
Remove the thermostat housing assembly.
Remove the water transfer tube.
Remove and discard the two o-rings.
Use the water tube driver, Part No. ST-1319 (20). Use a
hammer. Drive the water tube towards the front of the
engine until the back part of the tube clears the rocker lever
housing as shown.
Remove the Rocker Lever Housing

Remove the seven mounting capscrews and the rocker
lever housing.
Remove and discard rocker lever housing gasket.

ProCarManuals.com
Remove the Cylinder Head

CAUTION
component.
Remove the six capscrews and the cylinder head. Remove
and discard the gasket.
Remove the Cam Follower Assembly

Remove the cam follower cover.
Remove the cam follower assembly. Pull straight out until

the shaft is off the ring dowels.
Remove the Dipstick and Dipstick Tube (if equipped on

this side of engine)
Remove the dipstick and dipstick tube.
ProCarManuals.com
Remove the Fuel Pump

WARNING
sparks, arching switches or equipment, pilot lights, or
NOTE: Use two wrenches to remove the fuel tubes and
hoses.
Support the mating fittings with a wrench. Loosen the fuel
tube nuts with the other wrench.
Remove the fuel tubes, hoses and o-rings from the fuel
pump and fuel filter head.
Remove the fuel filter head.
Disconnect the fuel inlet hose (1). Disconnect the elec-

tronic fuel control valve supply hose (2). Remove o-rings.
Rail Applications
The lubricating oil scavenge pump (A) must be removed
prior to removing the fuel pump (B) to allow access to the
fuel pump mounting capscrews.
ProCarManuals.com
Remove the four mounting capscrews, and the fuel pump.

Remove the jaw coupling spider (23).
Remove the Air Compressor (Single Cylinder)

WARNING
When using a steam cleaner, wear protective clothing
and safety glasses or a face shield. Hot steam can
cause serious personal injury.
NOTE: The illustrations shown will be the SS model single
cylinder air compressor. Differences in procedures for SS,
QE and ST Cummins air will be shown where necessary.
Use steam to clean the air compressor.
Dry with compressed air.
Remove the fuel pump.
Remove the coolant lines from the air compressor.
CAUTION
This assembly weighs more than 23 kg [50 lb]. Handle
securely to avoid dropping.
Remove the air connections from the air compressor.
Remove the air compressor support bracket and capscrews.
Remove the four capscrews, the air compressor, and splined
ProCarManuals.com
coupling.
Remove the Air Compressor (Twin Cylinder)

Disconnect the coolant lines from the air compressor.
Remove the air inlet and outlet connections from the air
compressor.
Remove the air compressor support mounting capscrews

(5).
Remove the four capscrews (6).
Remove the air compressor.
Remove the splined coupling (1).
CAUTION
Use a capscrew in the shaft to prevent damage to the
shaft threads.
Install a [7/16-20x1 in] capscrew in the shaft.
Use a standard puller, Part No. ST–647, or equivalent.
Remove the accessory drive pulley.
Use a brass drift and remove the woodruff key from the
shaft.
Remove the capscrew from the shaft.
Remove the keyway seal.
Remove the Accessory Drive Seal

Remove the six button head hex socket capscrews.
ProCarManuals.com
Use three [1/4-20 x 1 in] capscrews to remove the seal from

the accessory drive shaft.
Install the three capscrews in the clinch nuts in the seal
case.
seal.
Remove the o-ring from the groove in the gear cover.

NOTE: The crankshaft pulley and damper have been re-
moved for clarity.
Remove the Accessory Drive Assembly

CAUTION
The woodruff key must be removed before removing the
accessory drive assembly. Damage to the bushing can
result.
Remove the four capscrews and the nut (31).
Remove the accessory drive assembly.
Disconnect the Engine Speed Sensor (ESS)

Disconnect the engine speed sensor (ESS) connectors
from the engine harness.
Loosen the locknut.
Remove the ESS from the cylinder block.
ProCarManuals.com
Disconnect the Lubricating Oil Pressure Sensor

Lift up on the tab and disconnect the connector from the
lubricating oil pressure sensor.
Use a deep flank drive socket, Part No. 3823843. Remove
the lubricating oil pressure sensor from the engine block.
Remove the Piston Cooling Nozzles

CAUTION
Do NOT attempt to remove the piston cooling nozzle
when the piston is at BOTTOM DEAD CENTER (BDC).
The nozzle will be damaged and can result in piston
failure.
Remove the piston cooling nozzle mounting capscrew.

Use a slide hammer with a [3/8 x 16 in] thread to remove
the nozzle.
Remove the Vibration Damper and Pulley Assembly

CAUTION
This assembly weighs more than 23 kg. [50 lb]. To avoid
component.
Remove one capscrew and install a [3/4-16x5 in] guide
stud.
ProCarManuals.com
CAUTION
Do not pry or hammer on the vibration damper. Damage
will result.
Remove the remaining capscrews, damper and pulley.
Remove the guide stud.
NOTE: Engines that do not have a belt driven fan hub have
an adapter instead of the pulley.
Remove the pulley from the damper.
Remove the Front Engine Support

Remove the front engine support.
Clean and check the support for reuse. Check for cracks
or damage.
Remove the Front Crankshaft Seal

Remove the eight button head hex socket capscrews.
Use four [1/4-20 UNCx1 in] capscrews to remove the seal

from the crankshaft.
Install the capscrews into the clinch nuts in the seal case.
seal.
ProCarManuals.com
Remove the Hydraulic Pump Drive Assembly

(if equipped)
Remove the hydraulic pump drive.
NOTE: Some engines contain a cover plate instead of a
hydraulic pump drive assembly.
Remove the hydraulic pump drive assembly.
Remove the Gear Cover Clamping Plate

NOTE: Some engines have two plates.
Rail Applications
Remove the front support mounting bracket by removing
fifteen capscrews and washers.
Rail Applications
Remove the scavenge line by disconnecting the tube from
the 90 degree elbow at the base of the front gear cover.
ProCarManuals.com
Remove the Front Gear Cover

NOTE: The master dowel must be removed before the gear
cover can be removed.
Use a 5/16-18 capscrew or a threaded rod. Use an old
piston pin or a slide hammer. Remove the dowel.
NOTE: The front cover contains five capscrews on the
bottom and three capscrews on back.
Remove the capscrews.
WARNING
This assembly weighs more than 23 kg. [50lb]. To avoid
personal injury, use a hoist or get personal assistance
to lift component.
NOTE: The gear cover has 21 capscrews in the front of the
cover and three, Nos. 1, 2, and 3, on the back side of the
cover.
Remove the 24 capscrews, four nuts, washers, and the
gear cover.
Remove the Water Pump Idler Gear

NOTE: The bolt-in idler shafts have a flange that require the
shaft, the idler gear, and the thrust washer to be removed
as an assembly.
Remove the capscrew from the idler gear.
NOTE: To remove the gear assembly, use two pry bars and
pry the gear and the shaft from the block.
Remove the hydraulic pump idler shaft and thrust bearings.

ProCarManuals.com
Remove the Camshaft Idler Gear

Remove the five capscrews, the retaining ring, and the front
thrust bearing.
Remove the camshaft idler gear.
Remove the rear thrust bearing, the idler shaft, and the
thrust bearing wear sleeve.
Remove the Thrust Bearing Plate

Remove the three 12-point capscrews and thrust bearing
plate.
Remove the Camshaft

CAUTION
Pilots must be used to prevent damage to the camshaft
and the bushings. Be sure the hooks do not damage the
camshaft bushings.
Use camshaft installation pilots, Part No. 3825150. Put the
pilots on the inner base circle of the valve lobes for the last
two cylinders before removing camshaft from block.
CAUTION
This part weighs more than 23 kg [50 lbs]. To avoid
component.
Rotate the camshaft during removal so that one of the pilots
is always on the bottom part of the camshaft bushing.
ProCarManuals.com
Remove the Lubricating Oil Pump

Remove the three capscrews from the oil pump mounting
flange.
Use a pry bar and gently pry the oil pump out of the engine
block.
Remove and discard the two o-rings and the seal ring from
the pump.
Remove the Front Gear Cover Spacer Plate

Remove the 14 mounting capscrews from the plate.
Remove the plate and discard the gasket.
NOTE: Tag the special mounting capscrews for future
identification.
Remove the Flywheel

CAUTION
component.
Use two [5/8-18 inch] guide studs to prevent the flywheel
from rotating. Remove two capscrews and install the guide
studs.
Use a hoist, two tee handles, and a lifting sling. Install the
tee handles.
Remove the remaining capscrews.
Remove the flywheel.
NOTE: Use a mallet to tap the flywheel from the crankshaft,
if necessary.
Remove the Rear Crankshaft Seal

Remove the seal mounting capscrews.
ProCarManuals.com
Use four [1/4-20 UNC x 1 inch] capscrews to remove the

seal from the crankshaft.
Install the capscrews in the welded nuts in the seal case.
seal.
Remove the Camshaft Cover Plate

Remove the three capscrews.
Remove the camshaft cover.
Remove the Lubricating Oil Pan and Lubricating Oil Pan

Adapter Cover Plate
Remove the 28 capscrews from the oil pan.
Remove the oil pan.
ProCarManuals.com
Remove the 18 capscrews from the cover plate.

Remove the cover plate.
Remove the Lubricating Oil Pan Suction Tube

Remove the three capscrews from the suction tube.
Remove the oil pan suction tube.
Remove the Lubricating Oil Pan Adapter

Remove the two [7/16-14 inch] capscrews, and the five
[3/8-16 inch] capscrews from the flywheel housing.
CAUTION
The component weighs 23 kg [50 lb] or more. To avoid
component.
Remove all of the capscrews and the pan adapter.
Remove and discard the gasket (40), the two rectangle
seals (41), and the seven bolt seals (42) from the adapter.
ProCarManuals.com
Remove the Rear Engine Mounts

Remove the rear engine mounts from the flywheel housing.
Remove the Flywheel Housing

CAUTION
component.
Use two guide studs to prevent the flywheel housing from
rotating during disassembly. Remove two capscrews. In-
stall the guide studs.
Use a hoist, a tee handle, and a lifting sling. Install the tee
handle. Adjust the hoist until there is tension in the lifting
sling. Remove the remaining capscrews.
Use a mallet and tap the flywheel housing off the two
locating dowels. Remove and discard the rectangular seal
and the bolt seals.
ProCarManuals.com
Remove the Rear Gear Drive - Upper Unit

NOTE: The hydraulic pump supports and the hydraulic
pump adapters can be different. Mark the parts for loca-
tion.
Remove the hydraulic pump support and the hydraulic
pump adapters or cover plates.
NOTE: Some engines will not have an outer hydraulic

drive. These engines require a cover plate and a nonsplined
shaft, but do not use a hydraulic gear.
If using a cover plate, remove the cover plate and nonsplined
shaft.
Remove the seven capscrews from each outboard hydrau-
lic drive or cover plate.
WARNING
Care must be taken to avoid possible breakage of the
capscrew mounting flanges.
CAUTION
This component weighs 23 kg [50 lb.] or more. To avoid
component.
The outboard hydraulic pump supports must be rotated to
remove from the housing. Use a mallet. Carefully tap the
side of the support.
Use a pry bar. Remove both outboard hydraulic pump

supports.
ProCarManuals.com
CAUTION
component.
Use a hoist and lifting sling. Install the lifting sling around
both sides of the upper housing. Adjust the hoist until there
is tension in the lifting sling.
CAUTION
The center gear in the drive protrudes from the bottom
of the housing. Use wood blocks (2) to level the gear
and to prevent the part from being damaged.
Remove the four capscrews from the top of the housing (A),
the four internal capscrews (B), the two capscrews from the
bottom of the upper housing on the left side (C), and the
three capscrews from the bottom on the right side (D).
Remove the rear gear train upper housing from the lower
housing.
Remove the gasket. Keep the gasket for future use.
Remove the Rear Gear Drive - Lower Unit

CAUTION
The component weighs 23 kg [50 lb.] or more. To avoid
component.
With the flywheel housing removed. Use a hoist, two tee
handles, and a lifting sling. Install the tee handles. Adjust
the hoist until there is tension in the lifting sling.
Use a mallet. tap the rear gear train lower housing off the
two locating dowel pins in the rear face of the cylinder
block.
Remove and discard the rectangular seal, bolt seals, and
main oil rifle seal.
Rotate the crankshaft by hand to position a connecting rod

at bottom dead center (BDC).
ProCarManuals.com
The connecting rods must have the cylinder number

marked on both the rod and the cap on the side positioned
toward the camshaft. Check the rods for correct markings.
Use a steel stamp and mark any rod that is not correctly
marked.
Loosen the capscrews until there is 6 mm [1/4 inch] of
clearance between the rod cap and the capscrew head.
Use a mallet. Tap the connecting rod capscrews until the

connecting rod cap and rod separate.
Remove the capscrews and the cap.
Remove the lower rod bearing. Use a awl and mark the
bearing position in the tang area.
NOTE: Mark the cylinder number and the letter “L” in the
flat surface of the bearing tangs.
After installing two guide pins, Part No. 3375098, in the

connecting rod, push the rod up far enough to allow the
upper bearing shell to be removed. Use a “T handle” piston
pusher to push the rod away from the crankshaft.
Remove the Piston and Rod Assembly

Protect the push rod galleys, coolant passages and oil
passages from contamination.
ProCarManuals.com
CAUTION
Do not use abrasive paper to remove the carbon de-
posits. Small particles of abrasive paper will cause se-
vere engine damage.
Use a scraper or a similar blunt-edged tool to loosen the
carbon deposits.
CAUTION
Use extreme care to be sure that no abrasive cleaners
or materials are used in the piston ring travel area.
Remove the remaining carbon with a nylon abrasive pad,
Scotch-Brite 7448, or equivalent, and solvent. The carbon
must be removed, but the surface does not have to appear
like new metal.
WARNING
Wear eye protection to prevent serious eye damage
during this operation.
An alternative method to remove the carbon ridge is to use
a high quality-steel wire wheel installed in a drill.
NOTE: Do not use a steel wire wheel of inferior quality
because the wire wheel will lose steel bristles during op-
eration, and cause additional contamination.
NOTE: Do not use a steel wire wheel in the piston ring
travel area. Operate the wire wheel in a circular motion to
remove the deposits.
Use two connecting rod guide pins, Part No. 3375098, or

equivalent. Install the guide pins in the connecting rod.
Push the piston and connecting rod up until the piston rings
are above the cylinder liner.
ProCarManuals.com
CAUTION
Put the piston and rod assembly in a rack to prevent
damage to the piston and rod assembly.
Remove the piston and rod assembly.
Remove the upper connecting rod bearing.
Use an awl and mark the bearing position in the tang area.
Disassemble the Connecting Rod and Piston

Remove piston rings.
Use internal snap ring pliers. Remove the snap rings from
both sides of the piston.
CAUTION
To prevent personal injury and damage to the piston, do
not drop the piston while removing the piston pin.
When the piston pin is removed from an articulated piston,
the skirt will separate from the crown.
The skirts and crowns are interchangeable.
NOTE: It is recommended that these parts be kept together
for possible failure analysis.
Main Bearings - General Information

NOTE: The upper bearings contain an oil hole. The lower
bearings do not have an oil hole. Both bearings are marked
on the back side indicating location (UPPER or LOWER)
and size (STANDARD [STD] or OVERSIZE [OS]). The
amount of OS is indicated in U.S. customary inches.
Use the same size bearing [STD, 0.010, 0.020, or 0.030]
that was removed.
ProCarManuals.com
The crankshaft will be stamped on the end of the No.1

counterweight to indicate if it has been ground under size.
Thrust bearing size is stamped on a crankshaft counter-
weight adjacent to the thrust location.
NOTE: The location number (No.) of the main bearing caps,

beginning at the front, are No. 1 through No. 7.
The main bearings are two widths. The narrow main bear-
ings fit locations No. 1 and No. 7. The wide bearings fit the
remaining locations.
Remove the Lower Main Bearing

CAUTION
Remove the bearings one pair at a time. Personal injury
and damage to the crankshaft can result if the crank-
shaft falls.
The main bearings caps must be marked for position. The
last number on each bearing cap identifies the cap location
position in the block.
The block and main bearing cap identification numbers
must be identical.
Use a steel stamp and mark any cap that is not marked
correctly.
Loosen the main bearing cap capscrews until there is ap-

proximately 13 mm [1/2-inch] between the capscrew head
and the cap. Use two pry bars to loosen the cap. Put the
pry bars in the notches at the sides of the caps.
Remove the cap and capscrews.
ProCarManuals.com
Remove the lower bearing. Use an awl and mark the bear-
ing position in the tang area.
NOTE: Mark the bearing position for future identification or
for possible failure analysis.
Remove the Lower Thrust Bearings

The No. 6 cap contains two thrust bearings.
Remove and mark them for position in the notched area.
Remove the Upper Thrust Bearings

Remove the upper thrust bearings from the block at the No.
6 location. Mark them for position.
NOTE: If necessary, slide the crankshaft to the front or to
the rear to allow the thrust bearings to be removed.
Remove the Crankshaft

WARNING
This assembly weighs more than 23 kg [50 lb.] To avoid
component.
Remove the main bearing caps and bearings.
Support the weight of the crankshaft with a hoist or lifting
ProCarManuals.com
device.
Remove the crankshaft.
Remove the Cylinder Liner

Use the universal liner puller, Part No. 3376015.
Loosen the set screws (44). Turn the feet (45) of the puller
until the curved side turns away from the center as shown.
Move the holding pins (46) to the last hole as shown.
Install the tool in the cylinder liner. The puller feet must not
touch the top of the liner. The puller arms must be posi-
tioned firmly on the bottom of the liner.
Turn the puller screw until the liner loosens in the block.
Remove the tool and the liner.
Use a liquid metal marker to mark the cylinder number on

each liner.
If sealing rings were used, do the following:
• Use a tag to mark the cylinder number.
• Measure in several places and record the thickness
of the sealing rings used in each cylinder. The thick-
ness of the sealing ring is one factor in determining
liner protrusion. This information must be known
ProCarManuals.com
when the liners are installed in the engine.

Engine Assembly (000-004) QSK19
Engine Assembly (000-004)

Assemble
Clean the bottom of the cylinder liner flange with solvent.
NOTE: The seal rings have three locating tabs on the I.D.
The tabs have an interference fit to the liner Lower Press
Fit (LPF) diameter to hold the seal ring in place during liner
installation.
Install the seal rings.
The seal ring must be straight on the liner upon installation.
Use your fingers to push the seal ring near the tabs to fit
the seal ring down and over the LPF diameter during in-
ProCarManuals.com
stallation.
This practice during installation of the seal ring will prevent
deformation that will result in the seal ring not fitting
squarely on the bottom of the liner flange.
Install the crevice seal. The beveled edge of the crevice

seal (2) must be positioned as shown.
NOTE: Some o-rings have a ‘‘D’’ shape cross section. This
type of o-ring must be installed with the flat side against the
cylinder liner.
Install o-rings in the position shown. Use the mold mark on
the o-ring to check if the o-ring is twisted.
(1) Liner, counterbore sealing ring

(2) Crevice seal
(3) Black o-ring
(4) Red o-ring
Use vegetable oil to lubricate the I.D. of the packing ring

bores.
Use your hands to push the cylinder liners into the block.
NOTE: Do not use RTV or other sealants under liner flange.
QSK19 Engine Assembly (000-004)
Use liner installation tool, Part No. 3375422, or equivalent.

Install the bridge assembly and two cylinder head
capscrews. Tighten the capscrews.
Install the pusher plate in the liner. Be sure it is aligned
correctly in the liner. Turn the pusher screw until it touches
the plate.
Turn the pusher screw until the liner flange touches the
counterbore ledge. Do not use more than 65 N•m [50 ft-lb]
of torque. Remove the tool.
NOTE: New cylinder liners can be 0.005 mm to 0.015 mm

[0.0002 inch to 0.0006 inch] smaller than the minimum
specifications because of the LubriteT coating.
Use a dial bore gauge and measure the I.D. of the liner at
the top, bottom, and middle of the liner.
ProCarManuals.com
Perform two measurements at each location. The mea-

surements must be 90 degrees apart.
Cylinder Liner I.D. (New)

mm in
158.737 MIN 6.2495
158.775 MAX 6.2510
The I.D. must be no more than 0.076 mm [0.003 inch]
out-of-round at the top two measurements.
If the I.D. is more than 0.05 mm [0.002 inch] out-of-round
in the bottom measurement location, the liner must be
removed.
Check for a twisted o-ring.
Measure the liner protrusion.

If the protrusion is not correct, the liner must be removed.
The protrusion can be adjusted using seal rings and/or
machining the counterbore ledge.
Cylinder Liner Protrusion

mm in
0.13 MIN 0.003
0.18 MAX 0.007
Main Bearings - General Information

NOTE: The upper bearings contain an oil hole. The lower
bearings do not have an oil hole. Both bearings are marked
on the back side indicating location (UPPER or LOWER)
and size (STANDARD [STD] or OVERSIZE [OS]). The
amount of OS is indicated in U.S. customary inches.
Use the same size bearing [STD, 0.010, 0.020, or 0.030]
that was removed.
The crankshaft will be stamped on the end of the No.1

counterweight to indicate if it has been ground under size.
Thrust bearing size is stamped on a crankshaft counter-
weight adjacent to the thrust location.
ProCarManuals.com
NOTE: The location number (No.) of the main bearing caps,

beginning at the front, are No. 1 through No. 7.
The main bearings are two widths. The narrow main bear-
ings fit locations No. 1 and No. 7. The wide bearings fit the
remaining locations.
WARNING
This part weighs more than 23 kg [50 lb]. Personal injury
can result.
Use a lint free cloth. Clean the bearing and the mounting
surface.
CAUTION
Do not lubricate the back of the bearing.
CAUTION
Prevent dirt from mixing with the lubricant. Dirty lubri-
cant will cause low mileage failures.
Align the tang in the bearing with the slot in the block.
Install the bearings. The end of the bearing must be even
with the main bearing cap mounting surface.
Use engine oil if the engine will be operated immediately.
Use LubriplateT No. 105, or equivalent if the engine will not
be operated immediately. Lubricate the bearings
Use a lint free cloth. Clean the crankshaft bearing journals.
CAUTION
ProCarManuals.com
Use a lifting strap that will not damage the crankshaft.

Do not drop the crankshaft on the bearings.
The end of the crankshaft with the smallest diameter must
point toward the front of the block. Install the crankshaft.
Use the same lubricant that was used on the upper main
bearings. Lubricate the upper thrust bearings.
CAUTION
The grooves in the thrust bearings must point toward
the crankshaft.
Install the bearings in the No. 6 location.
NOTE: Move the crankshaft to the front or rear to install the
second thrust bearing.
Use a lint-free cloth. Clean the lower main bearings, the
lower thrust bearings, and the mounting surfaces.
NOTE: Do not lubricate the back of the main bearings.
Align tang (1) in the bearing with the slot (2) in the main
bearing cap. Install the bearing. The end of the bearing
must be even with the main bearing cap mounting surface.
Lubricate the bearing surface with engine oil.
Lubricate the cap screw head and threads with SAE EP

140W oil. Allow excess oil to drip off of the capscrews
before installing in the block.
Install capscrews in the cap.
CAUTION
The grooves in the thrust bearing must point toward the
crankshaft. The dowels that secure the bearings must
not protrude above the housing.
Install the two thrust bearings on No. 6 main bearing cap.
CAUTION
The numbers on the main bearing caps must be the
same as the numbers on the block.
Check the numbers on the main bearing caps. The last
digit of each number (1 to 7), indicates the correct location.
ProCarManuals.com
Use engine oil. Lubricate the upper thrust bearings.
CAUTION
The grooves in the thrust bearings must point toward
the crankshaft.
Install the bearings in the No. 6 location.
NOTE: Move the crankshaft to the front or to the rear to so
the second thrust bearing to be installed.
CAUTION
Do not rotate the crankshaft until all of the main bearing
caps are pulled to the block. Damage will result if the
bearings move out of location.
NOTE: Use your hands to install the capscrews.
Turn each capscrew until it touches the main bearing caps
NOTE: Do not use an impact wrench. The bearing shells

can fall out.
Use both of the capscrews to pull the main bearing cap into
position.
Use two wrenches and tighten both capscrews at the same
time.
Check to be sure the No. 7 cap is even with the back of the
block.
ProCarManuals.com
Use the following steps and tighten the capscrews in the

sequence shown.
Torque Value:
Main Bearing
Cap Step 1 265 N•m [195 ft-lb]
Step 2 605 N•m [445 ft-lb]
Step 3 Loosen Loosen
Step 4 265 N•m [195 ft-lb]
Step 5 605 N•m [445 ft-lb]
NOTE: The crankshaft will turn freely if the main bearings

are installed correctly.
Use a dial indicator and measure the crankshaft end clear-

ance.
Crankshaft End Clearance

mm in
0.10 MIN 0.004
0.41 MAX 0.016
If the clearance is not within specifications, check for for-
eign material. Oversize thrust bearings are available to
adjust the end clearance.
NOTE: The upper and lower thrust bearing on the same
side of the main caps must be the same thickness.
Install a new snap ring in one piston pin bore of each piston
skirt.
Position the skirt over the piston crown.
NOTE: It is not necessary to heat the articulated pistons
before assembly. The piston pin is slip-fit.
ProCarManuals.com
CAUTION
Do not use a hammer to install the piston pin. The
piston can distort, causing it to seize in the liner.
Use engine oil. Lubricate the piston pin and connecting rod
bushing.
Align the pin bore of the rod with the pin bore of the piston
skirt and crown, and install the piston pin.
The snap ring must be seated completely in the piston

groove to prevent engine damage during engine operation.
Install a new snap ring in the piston pin bore.
NOTE: Do not install the piston rings until the pistons are
installed of the rods.
NOTE: The piston rings are marked with the part number.
The shipping package is marked with the location. The part
number on the ring must be positioned toward the top of
the piston.
Use a ring expander, Part No. ST-1269, or equivalent.
Install piston rings.
NOTE: Do not align the gap of a ring with the piston pin
bore.
NOTE: The gap in the oil ring expander must be turned 180
degrees opposite the gap on the oil ring.
Rotate the rings until the gaps are positioned as shown.

ProCarManuals.com
Use a lint-free cloth. Clean the connecting rod and the

bearing shells.
Install the rod bearing. Be sure the tang is positioned as
shown. The end of the bearing must be even with the cap
mounting surface.
CAUTION
Do not lubricate the back side of the bearing shells.
Use engine oil. Lubricate the bearing surface. The bear-
ings must be installed in their original location if new bear-
ings are not used.
NOTE: All of the rod bearings are identical.
Install two connecting rod guide pins, Part No. 3375098, in

the rod. The guide pins will aid the assembly and protect
the crankshaft.
CAUTION
The connecting rods and caps are not interchangeable.
The rods and the caps are machined as an assembly.
Failure will result if they are mixed.
Install the lower bearing shell in the rod cap. Be sure the
tang of the bearing shell is in the slot of the cap and the end
of the bearing is even with the cap surface.
Use engine oil. Lubricate the connecting rod capscrews

and washers as shown. Install the washers and capscrews
in the caps.
ProCarManuals.com
Lubricate the cylinder liner with engine oil. The entire bore
must be lubricated.
Immerse the piston in engine oil until the rings are covered.
Allow the excess oil to drip off of the assembly.
Check to be sure the ring gap position is still correct.
CAUTION
Be sure the rings fit correctly in the piston rings.
Use a piston ring compressor, Part No. 3375342, or equiva-

lent. Install the ring compressor on the piston.
NOTE: The ring compressor has a tapered bore. The small
end of the taper must be positioned toward the piston skirt.
ProCarManuals.com
CAUTION
The cylinder number on the rod and cap must be the
same.
CAUTION
The side of the rod with the cylinder number (bearing
tang side) must be toward the camshaft.
Rotate the crankshaft until the journal for the rod being
installed is at bottom dead center (BDC).
NOTE: If the engine has a crankshaft with bolt-on coun-
terweights, the journal must be at ‘‘TDC’’ top dead center.
Check the crankshaft rod journals for damage.

Install the rod and piston until the ring compressor touches
the block. Align the rod with the crankshaft journal.
Hold the ring compressor firmly against the block. Use a
wooden hammer handle to push the piston into the liner.
Push the piston into the bore until the rod bearing contacts
the crankshaft journal. Remove the guide pins.
ProCarManuals.com
CAUTION
The cylinder number on the rod and cap must be the
same.
CAUTION
The side of the cap with the cylinder number marking
(bearing tang side) must be toward the camshaft.
Install the connecting rod cap.
Tighten the capscrews alternately and evenly to pull the

cap over the dowel pins. Use the following steps to tighten
the capscrews.
Torque Value:
Connecting
Rod Capscrews Step 1 100 N•m [75 ft-lb]
2 205 N•m [150 ft-lb]
3 339 N•m [250 ft-lb]
4 Loosen Loosen
5 100 N•m [75 ft-lb]
6 205 N•m [150 ft-lb]
7 339 N•m [250 ft-lb]
Check the side clearance between the rod and the crank-
shaft.
The rod must move freely from side-to-side.
Measurements over 0.51 mm [0.020 in] must be measured
with dial indicator.
Maximum side clearance for used clearance is 5.1 mm
[0.200 in].
Connecting Rod and Crankshaft Side Clearance

New or Remanufactured Parts
mm in
0.20 MIN 0.008
0.35 MAX 0.014
NOTE: Tighten the suction tube to the block capscrews

before installing any support bracket capscrews.
NOTE: The suction tube shape can vary from the illustra-
tion. All suction tubes attach to the block in the same
manner.
Install the gasket, oil suction tube, washers, and capscrews.
Tighten the capscrews.
ProCarManuals.com

CAUTION
Do not pry or bend the suction tube to get the support
bracket capscrew holes to align.
Connect the support bracket to the adapter with the
capscrew.
Separate the gasket as shown.

Discard the center tab sections.
The diamond dowel (15) must be installed with the flat

surface turned toward the master dowel hole at the lower
right hand corner of the block. Guide studs (14) will aid the
installation.
CAUTION
Do not use gasket cement. Damage to the gasket will
result.
Use Cummins sealant, Part No. 3823494, or equivalent.
Apply a small amount to both sides of the gasket at the butt
joint. Install the gasket.
NOTE: The bottom of the gasket must be even with the
ProCarManuals.com
bottom of the block and the spacer plate.
NOTE: Special capscrews are required to attach the spacer

plate and the gear housing. The capscrews have a captive,
cone-shaped washer to maintain torque.
Install the spacer plate and the 11 capscrews as shown.

Remove the guide studs (14).
NOTE: If the oil pan adapter is removed, spacer plate

alignment must be checked. If the oil pan adapter is in-
stalled, alignment does not require checking.
Use a gauge block, Part No. ST-547, or equivalent, and
measure the distance from the bottom of the block to the
bottom of the plate.
The bottom of the plate or housing must be within 0.05 mm
[0.002 inch] of the bottom of the block.
Align the plate or housing with the bottom of the block if
necessary.
Use the sequence shown and tighten the capscrews.

Measure the plate or the housing to the block alignment
again to be sure it is within specifications.
ProCarManuals.com
Install the camshaft gear.
Camshaft keys are available in different sizes (amount of

offset). The injection timing is controlled by:
• the selection of the camshaft key.
• the direction of the key offset when compared to the
camshaft gear rotation.
• the amount of offset.
Install the same part number key in the same orientation as
the key that was removed.
CAUTION
Wear protective clothing to prevent personal injury from
burns.
CAUTION
Do not exceed the specified time or the temperature.
Damage to the gear and the gear teeth will result.
CAUTION
Do not attempt to install the gear without using heat.
Use an oven and adjust the heat to 235° C [450° F]. Heat
the gear for a minimum of 1 hour, but no more than a
maximum of 6 hours. The I.D. of the gear will become larger
and will simplify installation.
CAUTION
burns.
CAUTION
Allow the gear to cool slowly. Do not use water or oil to
reduce the cooling time. This will cause the gear to
ProCarManuals.com
crack.
NOTE: The timing mark on the camshaft gear must be
visible from the front of the gear after it is installed on the
camshaft.
Remove the gear from the oven and install on the camshaft.
The keyway in the gear must be aligned with the key in the
camshaft.
Use a dial indicator and measure the camshaft end clear-

ance.
Camshaft End Clearance

mm in
0.15 MIN 0.006
0.33 MAX 0.013
If the clearance is too small, check for foreign material or
a piece of gasket between the thrust plate and the block.
Install the hydraulic pump idler gear.
CAUTION
Engines that contain a hydraulic pump must have the oil
holes in the hydraulic pump idler shaft as shown. Idler
gear bushing failure will result if the oil holes are not
aligned correctly.
Mark the flange to show oil hole orientation.
ProCarManuals.com
CAUTION
The grooves in the thrust washers must be turned to-
ward the gear.
Use LubriplateT No. 105, or equivalent. Lubricate the gear,
bushing, shaft, and the thrust washer.
Use engine oil. Lubricate the capscrew. Assemble the parts
as shown.
CAUTION
Engines that contain a hydraulic pump must have the oil
holes in the hydraulic pump idler shaft oriented as
shown. Idler gear bushing failure will result if the oil
holes are not aligned correctly.
Align the oil holes in the shaft to an angle 45 degrees to the
left of vertical.
Use the capscrew to pull the shaft into the bore. Tighten the
capscrew.
CAUTION
Engines that do not have a hydraulic pump drive must
have a plug installed in place of the idler shaft. Low oil
pressure will result if the plug is omitted.
CAUTION
The capscrew that is used for the lug must not protrude
beyond the block.
Use a 9/16–UNF-inch capscrew, lock washer, and a plain
washer that is larger than the block bore. Tighten the
capscrews.
Use a dial indicator and measure the idler gear end clear-
ance.
Hydraulic Pump Idler Gear — End Clearance

mm in
0.10 MIN 0.004
0.36 MAX 0.014
NOTE: If the clearance is not within specifications, check
for foreign material between the parts, or check for proper
ProCarManuals.com
location of the thrust washers. Oversize thrust washers are

available.
Install the water pump idler gear.
CAUTION
The grooves in the thrust washers must be turned to-
ward the gear.
use LubriplateT No. 105, or equivalent. Lubricate the gear,
bushing, shaft, and thrust washer.
Use engine oil. Lubricate the capscrew. Assemble the parts
as shown.
Align the oil holes in the shaft to an angle 45 degrees to the

left of vertical.
Use the capscrew to pull the shaft into the bore. tighten the
capscrew.
Use a dial indicator and measure the idler gear end clear-
ance.
Water Pump Idler Gear — End Clearance

mm in
0.10 MIN 0.004
0.36 MAX 0.014
ProCarManuals.com
location of the thrust washers. Oversize washers are

available.
Install the camshaft idler.
NOTE: If the idler shaft ring dowel remained in the cylinder

block during disassembly, remove the dowel from the block
and install it into the idler shaft. The bore in the thrust
bearing wear plate and the O.D. of the dowel are designed
to provide a slight press fit to hold the wear plate in position
during installation of the idler assembly.
CAUTION
The grooves in the thrust bearing must be positioned
toward the gear.
NOTE: The timing marks on the camshaft gear must be
visible when the gear is installed.
Use LubriplateT No. 105, or equivalent. Lubricate the gear,
bushing, shaft, and thrust washier.
Use engine oil. Lubricate the capscrews. Assemble the
parts as shown.
NOTE: The camshaft idler gear is the only idler gear that
has timing marks.
Align the “O” on the idler gear with the “O” on the crank-
shaft gear. Align the “X” on the camshaft gear with the “X”
on the idler gear.
ProCarManuals.com
Rotate the idler shaft as necessary to align the mounting

capscrew holes.
Use the capscrew to pull the shaft into the bore.
Use the following steps and tighten the capscrews in the
sequence shown.
Torque Value:
Step 1 45 N•m [35 ft-lb]
Step 3 150 N•m [110 ft-lb]
Use a dial indicator. Measure the idler gear end clearance.
Camshaft Idler Gear — End Clearance

mm in
0.29 MIN 0.012
0.51 MAX 0.020
location of the thrust washers. Oversize thrust washers are
available.
Static Injection Timing-Check

If the camshaft or camshaft gear was replaced, check the
injection timing. Machine tolerances can cause the timing
to be out of specifications.
CAUTION
Use ONLY the crankshaft to rotate the engine. The use
of the gears will result in false measurement. Gear lash
must be closed up in the direction of normal rotation.
NOTE: Three guide bolts equally spaced in front of the
crankshaft will help rotate the engine.
Turn the crankshaft in the direction of normal rotation while
ProCarManuals.com
observing both of the timing tool plungers. Both plungers

will begin moving upward when the cylinder is on the com-
pression stroke.
NOTE: Assuming all the gear index marks were aligned
when the injection timing process was started, the crank-
shaft will have to be rotated approximately three-quarters
of a revolution to get to the compression stroke for the No.
3 cylinder.
If both plungers are not moving upward (one upwardand
one downward), the engine is on the exhaust stroke. Ro-
tate the crankshaft one revolution to get to the compression
stroke.
Establish Top Dead Center (TDC) by slowly rotating the

crankshaft in the direction of normal rotation while observ-
ing the piston plunger (10). The plunger will move upward,
STOP, then begin to move downward. The STOP point of
the plunger is TDC. Rotate the engine opposite the di-
rection of normal rotation until the plunger begins to moves
downward. The cylinder is now Before Top Dead Center
(BTDC) slightly.
Turn the indicator so that the stem is touching the plunger.

Carefully move the indicator downward until the needle
has turned a minimum of five revolutions 12.7 mm [0.500
inch]. LOCK the indicator in position.
Slowly turn the crankshaft in the direction of normal rotation
until the indicator needle STOPS turning clockwise (TDC).
Move the indicator downward until there is ONLY one
revolution 2.54 mm [0.100 inch] of travel remaining until the
indicator bottoms out.
Adjust the indicator to ZERO.
Turn the push rod indicator so that the stem touches the
plunger.
Carefully lower the indicator until it bottoms out. Raise the
indicator when the needle has turned a minimum of three
revolutions 7.62 mm [0.300 inch].
ProCarManuals.com
Slowly turn the crankshaft in the direction of normal rotation

until the push rod indicator STOPS (1), momentarily re-
verses direction (2) (this is the crush nose on the cam-
shaft), and STOPS again (3). The cam follower is now on
the outer base circle of the camshaft. The piston is now
approximately 45 degrees After Top Dead Center (ATDC).
CAUTION
It is important to record the amount of travel remaining
in the push rod travel indicator for later reference.
Carefully lower the push rod travel indicator until it bottoms
out. Raise the indicator approximately one-half of a revo-
lution 12.7 mm [0.050 inch]. LOCK the indicator in position.
Set the indicator at ZERO.
Set The Piston at 5.1613 mm [0.2032 inch] BTDC

Observe the piston travel indicator as you slowly rotate the
crankshaft opposite the direction of normal rotation.
STOP rotating the crankshaft when the piston travel indi-
cator indicates the piston is at TDC (ZERO).
CAUTION
The crankshaft must be turned slowly to accurately
count the indicator revolutions.
Turn the crankshaft opposite the direction of normal rota-
tion until the indicator needle moves two and one-half revo-
lutions 6.35 mm [0.250 inch].
The piston is now 6.35 mm [0.250 inch] BTDC.
CAUTION
ONLY move the piston to 5.1613 mm [0.2032 inch] BTDC
by turning the crankshaft in the direction of normal
rotation. If you accidently turn the crankshaft too far,
you must turn the crankshaft opposite the direction of
normal rotation MORE than 5.1613 mm [0.2032 inch]
BTDC. Then very slowly turn the crankshaft in the di-
rection of normal rotation until the indicator indicates
ProCarManuals.com
that the piston is 5.1613 mm [0.2032 inch] BTDC.

NOTE: Remember that all QSK19 injection timing speci-
fications are more than one indicator revolution [0.100
inch].
Read the push rod travel indicator counterclockwise from
ZERO. This is the injection timing measurement to com-
pare to the specification. An example of .354 mm [0.118
inch] is shown.
If you are not sure of the number of push rod indicator

revolutions, check by carefully lifting the indicator stem
until the indicator has bottomed out. Lower the stem the
amount of excess travel you set in the third preceding step.
Lower the stem to the plunger. Read the indicator.
If the injection timing is within specification and you are
using a slipper-fit gear, install the standard gear. Repeat
the injection timing procedure after the camshaft gear has
cooled.
If the injection timing is not within specification, repeat the

measurement procedure to check the tool setup and the
ZERO settings.
If the timing is still not within specification, the camshaft
key must be changed.
Record the orientation of any offset of the key. Use the
following worksheet to determine an alternate key.
CAUTION
You must confirm the timing measurement after change
the key.
ProCarManuals.com
ProCarManuals.com
ProCarManuals.com
ProCarManuals.com
ProCarManuals.com
Install the gear cover and related components.
NOTE: Trim the gasket to the correct width since the spacer
plate is already installed.
Install the service gasket piece on top of the oil pan adapter.
Use a spray adhesive to hold it in position. Use Cummins
sealant, Part No. 3823494, at the joints.
ProCarManuals.com
This illustration shows the capscrew length requirements

for the front cover.
NOTE: Do not tighten the capscrews until the master dowel

pin is installed.
The use of guide bolts will aid the assembly. Install the front
cover gasket, cover, and capscrews.
Put the clamping plate in position and begin the installation

of the capscrew.
NOTE: The plate must remain loose until the fan hub or the
cover plate is installed.
Use a 5/16-8x3 inch capscrew and a mallet. Install the

threaded master dowel. Drive the dowel in until it touches
the bottom of the hole in the block.
ProCarManuals.com
Tighten the mounting capscrews in the sequence shown.

NOTE: Capscrew No. 1, 2, and 3 are located at the back
of the spacer plate.
Install the five capscrews that attach to the bottom of the

oil pan adapter. Tighten the capscrews.
Install the hydraulic pump drive.

Using engine oil, lubricate the bushing in the cover.
Install the gasket, drive or cover, washers, and capscrews.
NOTE: If an SAE 1 flywheel housing option is used, there

must be two [5/8–11 x 6 1/2 in] studs, Part No. 3065777,
installed in the upper holes of the cylinder block.
Apply a small amount of LubriplateT 105 or gasket adhesive
on the seal ring groove, the capscrew counterbores, and
the dowel counterbores on the block side of the lower
housing.
Install the new rectangular seal ring, with the joint at the top
ProCarManuals.com
into the groove in the lower housing.

Install the ten new capscrew seals into the capscrew
counterbores in the lower housing.
Use LubriplateT 105 or equivalent on the main rifle seal.
Install the main rifle seal into the counterbore surrounding
the main rifle drilling.
CAUTION
Caution: The component weighs 23 kg [50 lb] or more.
To avoid personal injury, use a hoist or get assistance
to lift the components.
Install two 5/8-11x1/2 inch guide studs into the rear face of
the cylinder block. Use a hoist, two tee handles, and a
lifting sling. Install the tee handles.
Lift the lower housing of the rear gear train.
Install the lower housing of the rear gear train onto the
dowel pins.
Check the alignment of all capscrews seals, rectangular
seal, and the main oil rifle seal.
Use two 5/8-11x5 inch capscrews with flat washers in the
locations shown.
Tighten the capscrews alternately to pull the lower housing
to the block.
Use a dial indicator. Be sure the two capscrews are holding

the lower housing firmly against the cylinder block. Check
the gear lash.
Lower Housing-To-Cylinder Block Gear Backlash

mm in
0.05 MIN 0.002
0.51 MAX 0.015
If the gear lash is above acceptable limits, the rear gear
train lower idler gear or crankshaft gear must be replaced.
NOTE: Replace the idler gear first.
If the gear lash is below acceptable limits (or if the gear
replacement does not correct the lash), replace the
housing.
Use LubriplateT No. 105 or gasket adhesive on the seal ring

groove and the 10 capscrew counterbores on the rear gear
train lower housing side of the flywheel housing.
Install the new rectangular seal ring, with the joint at the
top, into the groove in the flywheel housing.
Install the new capscrew seals and dowel seals into the
ProCarManuals.com
CAUTION
personal injury, use a hoist or get assistance to life the
component.
Use two 5/8-11x6 1/2 inch guide studs. Use a hoist, tee
handles, and a lifting sling. Install the flywheel housing onto
the dowels in the rear gear train lower housing.
Install the lock washers, capscrews, and nuts.
Use the following steps.

Tighten using the sequence shown.
Torque Value: Step 1 100 N•m [75 ft-lb]
2 205 N•m [150 ft-lb]
Install the two capscrews 7/16-14x4 3/4 inch, Part No.

190799, and the five capscrews 3/8-16x4 3/4 inch, Part No.
S106-C, with flat washers and lockwashers.
Torque Value:
3/8-16 inch 45 N•m [35 ft-lb]
7/16-14 inch 65 N•m [50 ft-lb]
Install the upper housing of the rear gear train.

ProCarManuals.com
Use gasket adhesive on the gasket. Do not use an exces-

sive amount of adhesive on the gasket.
Align and install the rear gear train upper housing gasket
to the rear gear train lower housing.
CAUTION
The component weighs 23 kg [50 lbs.] or more. To avoid
component.
NOTE: Use extra care when aligning the upper housing
onto the lower housing to prevent gasket damage.
Use the dowel pins to align the upper housing onto the
lower housing.
Use only SAE Grade 8 capscrews to install the upper

housing. Install the following capscrews according to the
table below.
Ref Location Part No. Size [inch] Qty
1 Top-Front 3202224 1/2-13 x 9 2
1/4
2 Top-Rear 3202223 1/2-13 x 7 2
1/2
3 Internal 1691695 1/2-13 x 1 4
3/4
4 Bottom-Left Side 3202222 1/2-13 x 1 2
3/4
5 Bottom-Right Side 3202222 1/2-13 x 1 3
3/4
Use the sequence shown to tighten the bolts.

Torque Value:
Step 2 150 N•m [110 ft-lb]
ProCarManuals.com
Use a dial indicator. Be sure the lower idler gear is secure.

If the gear is not secure, the indicator reading will include
the lower idler gear to the crankshaft gear backlash.
Idler Gear Backlash

mm in
0.05 MIN 0.002
0.51 MAX 0.020
If the gear lash is less than specified limits, thicker gaskets

are available. Do not use more than two gaskets to correct
the backlash.
If the gear lash is greater than the specification and the
thinnest gasket is used, the upper and lower gears must
be replaced.
Use LubriplateT No. 105, or equivalent. Lubricate the outer

hydraulic pump support bushing in the upper housing.
Lubricate the bushing surfaces on both shafts in the outer
hydraulic pump support drive assemblies.
Install the outer hydraulic pump support drive.

pump support drive. These engines require a cover plate
and a non-splined shaft, but do not use a hydraulic gear.
Use gasket adhesive sparingly. Install the hydraulic sup-
port housing gaskets to both support mounting flanges on
the outer hydraulic pump support drive assemblies.
ProCarManuals.com
If using the outer hydraulic pump support cover plate, in-

stall the non-splined shaft onto the cover plate. Use a
3/8–16 x 1-1/4 inch capscrew.
Tighten the capscrew.
Use three 7/16-14 x 4 inch guide studs. Install one outer

hydraulic pump support drive assembly.
Install four capscrews.

Hand-tighten the capscrews.
Remove the guide studs.
Install the remaining three capscrews. Use the sequence
and torque as shown.
Install the other outer hydraulic pump using the same

procedure.
ProCarManuals.com
NOTE: Be sure the flywheel housing dowels have been

installed in the block.
Install the sealing ring (7) in the groove on the housing. If
a wet type is used, install the seals (8) in the counterbores
as shown. The holes (9) do not require seals.
Use guide bolts to help during alignment. Install the hous-
ing and the capscrews.
Torque the flywheel housing capscrews using the sequence

shown.
2 205 N•m [150 ft-lb]
Measure the flywheel housing alignment.

NOTE: The bore and the face of the housing must be in
alignment with the crankshaft.
NOTE: The indicator arm must be rigid for an accurate
reading. It must not sag.
Attach an indicator to the crankshaft as shown.
Position the indicator at the 12 o’clock position. Adjust the

dial until the needle points to ZERO. Rotate the crankshaft
one complete revolution (360 degrees). Record the TIR.
ProCarManuals.com
The maximum allowable TIR depends on the diameter of

the bore.
Bore Diameter/Maximum TIR
MIN/MAX MIN/MAX SAE mm in
mm in No.
787.4/810.5 [31.00/31.91] 00 0.30 [0.012]
647.7/648.0 [25.50/25.51] 0 0.25 [0.010]
584.2/584.4 [23.00/23.008] 1/2 0.25 [0.010]
511.2/511.3 [20.125/20.13] 1 0.20 [0.008]
If the alignment is not within specifications and the bore is
round, the housing can be shifted.
If the alignment is not within specifications and the bore is
not round, the housing must be replaced.
NOTE: The crankshaft end clearance must be pushed or

pulled in the same direction each time a point is measured.
Attach an indicator as shown. Position the indicator at the
12 o’clock position. Adjust the dial until the needle points
to ZERO.
Record the indicator reading at 3 different points; 3 o’clock,

6 o’clock, and 9 o’clock.
Turn backward to the original position. Be sure the needle
still points to ZERO. Determine the total indicator runout
(TIR).
mm in
Example:
3 o’clock 0.00 [0.00]
6 o’clock +0.08 [+0.003]
9 o’clock -0.05 [-0.002]
——— ———-
Equal TIR: 0.13 [0.005]
The maximum allowable TIR depends on the diameter of

the bore.
Bore Diameter/Maximum TIR
MIN/MAX MIN/MAX SAE mm in
mm in No.
787.4/810.5 [31.00/31.91] 00 0.30 [0.012]
647.7/648.0 [25.50/25.51] 0 0.25 [0.010]
584.2/584.4 [23.00/23.008] 1/2 0.25 [0.010]
ProCarManuals.com
511.2/511.3 [20.125/20.13] 1 0.20 [0.008]

NOTE: If the alignment is not within specifications, remove
the housing. Check for nicks, burrs, or foreign material
between the block and the housing. Check the alignment
again. If the alignment is not within specifications, the
block or the housing is not machined correctly.
Tighten the five [3/8-inch] washers and capscrews in the

sequence shown.
2 40 N•m [30 ft-lb]
3 45 N•m [35 ft-lb]
Install the two [7/16-inch] washers and capscrews as shown.

Install the flywheel housing mounting capscrews.

Install a new o-ring on the seal housing.

Use vegetable oil to lubricate the o-ring.
ProCarManuals.com
To aid in seal installation, use a small nonmetallic bristle

brush to apply a thin film of 15W-40 oil to the inside di-
ameter of the seal case.
CAUTION
Do not allow oil to come in contact with other areas of
the seal to avoid damage to sealing surfaces.
Use hand pressure to push the seal on the crankshaft as

far as possible.
Use the pin supplied in the seal kit to align the seal mount-
ing holes with the mounting capscrew holes in the flywheel
housing.
Attach the seal installation tool that is supplied with the seal
to the crankshaft, using three flywheel mounting capscrews.
ProCarManuals.com
Align the installation tool with the pilot flange on the seal
carrier.
Tighten the three capscrews alternately and evenly in one-

half of a turn increments until the seal carrier seats against
the flywheel housing.
Remove the seal installation tool.
Install the seal mounting capscrews. Tighten the capscrews.

Torque Value: 11 N•m [95 in-lb]
ProCarManuals.com
NOTE: Use a contact adhesive such as 3M Spray 77 or 3M

4693 to hold the bolt seals in position.
Install the four bolt seals on the oil pan adapter.
The two rectangular seals have an adhesive on one side.
Remove the protective paper strips from the seals. Install
the seals on the oil pan adapter.
CAUTION
Gasket cement will prevent the gasket from sealing
properly.
4693 to hold the gasket in position.
Install the gasket. Make sure the gasket touches the rect-
angular seals.
Use Cummins sealant, Part No.3823494, or equivalent.

Apply the sealant as shown.
CAUTION
component.
NOTE: Be sure the seals remain in position when the
adapter is installed.
Lift the adapter up against the block surface, and then
ProCarManuals.com
move it back against the flywheel housing. Hand tighten

four capscrews to hold the adapter in position.
NOTE: The four capscrews shown must be tightened al-

ternately and evenly to be sure the adapter is pulled evenly
to the block and flywheel housing.
Install the four washers and capscrews as shown. Push the
adapter towards the block and flywheel housing while tight-
ening the capscrews.
Use the following steps while tightening the oil pan adapter
capscrews.
2 25 N•m [20 ft-lb]
3 40 N•m [30 ft-lb]
4 45 N•m [35 ft-lb]
Install the three capscrews located in the center of the

flywheel housing and tighten them in the sequence shown.
Use the steps and torque values below when tightening the
capscrews.
2 40 N•m [30 ft-lb]
3 45 N•m [35 ft-lb]
Install the two [7/16-inch] washers and capscrews shown.

NOTE: Capscrews No. 24 through 28 thread into the front

cover on engines.
Install capscrews 24 through 28.
Install the remaining [3/8-inch] washers and capscrews (1
through 23).
Tighten all the capscrews that thread into the block.
Torque Value:
ProCarManuals.com
Capscrews 1 – 23 60 N•m [45 ft-lb]

Torque Value:
Capscrews 24 – 28 45 N•m [35 ft-lb]
Install the [9/16-inch] washer and capscrew. Tighten the

capscrew.
Install the front engine support bracket.

CAUTION
This component weighs 23 kg [50 lbs.] or more. To avoid
component.
Install the support, washers, and capscrews. Tighten the
capscrews.
CAUTION
properly.
Install the gaskets and oil pan.
ProCarManuals.com
Use the sequence shown to install the capscrews.

Rail Applications
Install two 3/8 - 16 guide studs in the top row of capscrew
holes.
Rail Applications
CAUTION
properly.
Install the gasket and lubricating oil pan.
Rail Applications
Use the sequence shown to install the 38 capscrews.
ProCarManuals.com
Install the gasket. Install the water pump drive assembly.

The drive will be secured in position by the stud.
Install the o-ring in the groove in the gear cover.


brush to apply a thin film of clean SAE 15W-40 oil to the
inside diameter of the seal.
NOTE: Do not allow oil to come in contact with other areas
of the seal.
Install the seal on the alternator drive shaft.

ProCarManuals.com
Use the seal installation tool that is supplied with the ser-
vice seal to push the seal on the alternator drive shaft.
Put the installation tool against the seal.
Use the pulley installation tool, Part No. 3376426, to push

the seal on the alternator drive shaft.
Position the pulley installer on the accessory drive shaft.
Put the pulley installation housing on the pulley installer.
Align the three clinch nuts on the back of the seal carrier
flange with the three counterbores in the gear cover seal
mounting surface.
ProCarManuals.com
Use the tool to push the seal on the shaft until the seal
carrier flange contacts the gear cover.
Remove the pulley installation tool housing, seal installa-

tion tool, and pulley installer.
Install the six, button head hex socket capscrews.

Tighten the capscrews alternately and evenly.
CAUTION
Do not use a hammer to drive the pulley into position.
The thrust washers will be damaged.
Use the pulley installation kit, Part No. 3376326, or equiva-
lent. Install the correct adapter in the pusher.
Install the pulley on the shaft. The pulley must touch the
step on the shaft.
ProCarManuals.com
Remove the tool and adapter.
Install the o-ring in the groove in the gear cover.

brush to apply a thin film of clean SAE 15W-40 oil to the
inside diameter of the seal case.
NOTE: Do not allow oil to come in contact with other areas
of the seal.
Install the seal on the accessory drive shaft.
Use the seal installation tool that is supplied with the ser-
vice seal to push the seal on the accessory drive shaft.
Put the installation tool against the seal.
ProCarManuals.com
Use the pulley installation tool, Part No. 3376426, to push

the seal on the accessory drive shaft.
Position the pulley installer on the accessory drive shaft.
Put the pulley installation housing on the pulley installer.

Align the three clinch nuts on the back of the seal carrier
flange with the three counterbores in the gear cover seal
mounting surface.
Use the tool to push the seal on the shaft until the seal
carrier flange contacts the gear cover.
ProCarManuals.com
Remove the pulley installation tool housing, seal installa-

tion tool, and pulley installer.
Install the six button head hex socket capscrews. Tighten

the capscrews alternately and evenly.
Install the keyway seal.

Install the woodruf key into accessory drive shaft.
NOTE: Keyway seal must be installed prior to installation

of keyway and accessory drive pulley.
Install the accessory drive pulley.
ProCarManuals.com
CAUTION
Damage to the thrust bearing will result.
Use a pulley installation tool kit, Part No. 3376326. Insert
the appropriate adapter (7) in the pusher.
Lubricate the shaft O.D. and the pulley I.D. with engine oil.
Align the keyway in the pulley with the key in the shaft. Use
the tool to push the pulley on the shaft until it touches the
step on the shaft.
Use vegetable oil to lubricate the new o-ring. Do not soak

the new o-ring in engine oil.
CAUTION
Use care when handling the piston cooling nozzle. Any
damage to the piston cooling nozzle can result in major
engine damage.
Install the o-ring in the groove of the piston cooling nozzle
that is the least distance to the flange.
Install the piston ring type (steel) seal ring in the groove that
is the most distance from the flange.
Align one of the valve set marks with the mark cast in the
accessory drive seal boss.
ProCarManuals.com
Refer to the sequence chart illustrated to identify the two

piston cooling nozzles that can be installed.
CAUTION
Do not use the capscrew to pull the nozzle into the
cylinder block. Nozzles and o-ring damage or external
oil leaks can result.
Install the two piston cooling nozzles. Use only your hand
to push the nozzle into the bore until the flange touches the
block.
Install and tighten the capscrew.
Torque Value 45 N•m [35 ft-lb]
Rotate the barring device and align the next valve set mark
with the mark cast into the gear cover.
Repeat the process to install the remaining piston cooling
nozzles.
Install the air compressor.

ProCarManuals.com
Single Cylinder
Install the splined coupling (1) on the accessory drive shaft.
Be sure the gasket surfaces of the accessory drive and air
compressor are clean and not damaged.
Use a new gasket to install the air compressor.
CAUTION
Do not tighten any capscrew until the support bracket
is aligned.
Install the four capscrews and two nuts (2). The capscrews
(4) must be loose.
Install the two capscrews (5) for the bracket. The support
bracket must be flat against the block. Turn the compressor
until the bracket is flat.
Tighten the compressor to the accessory drive capscrews

(2).
Tighten the bracket to the block capscrews (5).
CAUTION
The bracket MUST be flat against the compressor.
Tighten the bracket to the compressor capscrew (4).
NOTE: If rubber grommets are used on the coolant lines,

be sure they are installed carefully to prevent cuts or tears
to the grommets which cause coolant leaks. When flexible
tubing is used, make sure that it does not rub any other
surface.
Install the coolant and air lines to the air compressor and
tighten.
Install the fuel pump drive coupling on the air compressor.
ProCarManuals.com
Install the gasket and the cover plate (support bracket) on

the compressor.
Do not tighten the six capscrews. The support must be
adjusted.
NOTE: Do not install the splined coupling or the mounting

gasket.
Install the compressor on the accessory drive.
Install the four capscrews (6). Only tighten the capscrews
enough to pull the compressor to the accessory drive. The
compressor must be turned to align the support bracket.
CAUTION
The support MUST be flat against the block. Rotate the
compressor until the support is aligned properly against
the block. If the support in NOT flat, the compressor
and/or accessory drive will fail.
Tighten the four capscrews (6).
The bracket must remain flat against the block. Tighten the
support capscrews (7) that are accessible.
Remove the four capscrews (6).

Remove the compressor.
Tighten the two remaining support to the compressor
capscrews.
ProCarManuals.com
Install the splined coupling (1), the gasket, and the com-
pressor.
CAUTION
The support MUST be flat against the block. Rotate the
compressor until the support is aligned properly against
the block. If the support is NOT flat, the compressor
and/or accessory will fail.
Install the four capscrews (6) and two capscrews (5).
Torque Value:
Capscrew (6) 60 N•m [54 ft-lb]
Capscrew (5) 45 N•m [35 ft-lb]
Install the lubricating oil filters.

Clean the top of the cylinder block and the cylinder liners.
Use a scraper or a fibrous abrasive pad such as Scotch-
Brite 7477, or equivalent, and solvent. Clean the top deck
surface of the block. Do not allow any dirt into the cylinder.
The surface must be free of dirt, oil, and gasket material,
but does not have to look like new metal.
NOTE: Check the top surface of the block for wear. If
fretting damage is present in an area where a head gasket
seal ring or a grommet makes contact, the surface must be
repaired. Refer to the Alternative Repair Manual.
NOTE: Fretting damage in any other area is acceptable
only if it does not change the protrusion measurement of
the counterbore or liner.
Visually inspect the groove pins for damage. Use the ST-
1134 dowel pin extractor, or equivalent to remove the pins.
ProCarManuals.com
Inspect the cylinder block to determine if an oversize or a

standard size head gasket is required.
NOTE: An oversize head gasket may be required on blocks
that have had material removed from the top surface of the
block. Check the block for markings indicating an over-
sized gasket is required.
NOTE: The word TOP stamped on top of the head gasket

must be visible after the gasket is installed.
Install the gasket.
Install the cylinder head. It must slide easily over the groove
pins.
Lubricate the capscrew head flange with SAE EP 140W oil.
Lubricate the capscrew threads with clean engine oil. Allow
excess oil to drip off of the capscrews before installing in
the block.
Install the capscrews.
NOTE: When using torque plus angle, the tolerance on the

90 degree angle of rotation is one to two flats (90 degrees
± 30 degrees). If the capscrew is rotated beyond two flats,
do not loosen the capscrew. The clamp load is still ac-
ceptable, however, rotating the capscrew beyond two flats
causes additional stretch and reduces the life of the
capscrew. With proper torquing, the capscrew can typically
be reused for the life of the engine.
After all capscrews on one head have been torqued to 300
ProCarManuals.com
N•m [220 ft-lb], they must be rotated in the tightening

direction an additional 90 degrees. Rotate the capscrew
until the mark on the cylinder head(1) is between the next
two marks joined by an arc (more than one flat and less
than two flats).
The markings on the head of the flange head capscrews

serve as an aid during installation. After torquing the
capscrew to 300 N•m [220 ft-lb], mark the cylinder head(1)
adjacent to one of the two single marks on the capscrew
head.
Tighten the capscrews using the following steps and in the

sequence shown.
2 205 N•m [150 ft-lb]
3 300 N•m [220 ft-lb]
4 Rotate 90 Degrees
Use clean, 15W-40 oil. Lubricate the o-rings.
Install the hold-down clamp on the side of the injector.

ProCarManuals.com
Install the injector and hold-down clamp in the cylinder

head.
Use injector installation tool, Part No. 3824830, it set the
injector in the bore.
The slide hammer will make a dull sound when the injector
is seated properly.
NOTE: If the injector installation tool, Part No. 3824830, is
not available, use a 40 mm (1 9/16-inch) socket with an
extension and a rubber mallet to install the injector.
Use clean, engine oil. Lubricate the injector hold-down

capscrew.
Install the injector hold-down capscrew.
Use vegetable oil. Lubricate the o-rings (2). Install the

o-rings.
Install the water transfer tube (1).
NOTE: The gasket and housing must be aligned correctly

with the dowel pins.
Install the gasket and the housing.
Install the seven capscrews.
ProCarManuals.com
Use the sequence shown to tighten the capscrews.

NOTE: The push rods must be seated correctly in the cam

followers.
NOTE: The injector push rods are thicker in the middle. The
valve push rods are the same for both intake and exhaust.
Use engine oil. Lubricate the sockets in the cam followers.
Install the push rods.
Lubricate the crosshead pockets with clean engine oil.
Install the valve crossheads.
Install the rocker levers.
NOTE: Be sure the ring dowel that aligns the rocker shaft
is installed in the housing.
NOTE: Be sure the adjusting screws are loose.
Position the rocker lever assembly on the housing. Install
the capscrews 2 or 3 revolutions.
Align the push rod sockets with the adjusting screws.
ProCarManuals.com
Adjust the valves and injectors.
NOTE: The barring device shaft turns approximately two

revolutions before the engine begins to turn. The device will
not turn the engine opposite the direction of normal rota-
tion.
Push the shaft in and turn the barring device counter-
clockwise until the ‘‘A’’ mark on the pulley is aligned with
the mark that is cast into the boss for the accessory drive
seal on the front gear cover.
Determine the Cylinder in Position for Valve Set

The valves will be adjusted on the cylinder that has all the
valves closed. Use the table to determine the cylinders for
valve position.
If the rocker lever assemblies have been removed, use this

step to determine the cylinder to be set.
NOTE: All adjusting screws must be loose on all cylinders,
and the push rod must remain in alignment.
NOTE: Perform this step on both cylinders to be checked.
Hold both rocker levers against the crossheads. Turn the
adjusting screws until they touch the push rods. Turn the
lock nuts until they touch the levers.
ProCarManuals.com
NOTE: The push rods will be the same height above the top
of the rocker lever housing on the cylinder ready for valve
adjustment.
If the rocker levers have not been removed, wiggle the

valve rocker levers on the two cylinders in question. Set the
valves on the cylinder where both levers feel loose.
Use the chart to determine the injector that is ready to

adjust.
NOTE: Adjustment can begin on any valve set mark.
In our example, assume the A mark is aligned and the push
rod heights indicate that the valves on cylinder No. 6 are
closed. The chart shows the valves on No. 2 are ready to
adjust. The chart shows the injector on cylinder No. 3 is
ready to adjust.
After the adjustment, bar the engine to the B set mark.
Adjust the valves on cylinder No. 4 and adjust the injector
on cylinder No. 6.
Valves – Setting
Valve Adjustment (Initial Set)
Reference mm in
Point
A 0.81 Exhaust 0.032
B 0.36 Intake 0.014
NOTE: To provide a consistent set, lubricate the adjusting

screws prior to setting the valves.
NOTE: Be sure the crosshead is firmly in place on the valve
stem tips.
NOTE: Be sure the feeler gauge is under the center of the
ball and socket, or the socket can rock or tip, resulting in
an incorrect adjustment.
Select a feeler gauge for the correct valve lash specifica-
ProCarManuals.com
tion. Use service tool Part No. 3824901. Insert the gauge
(2) between the rocker lever socket and the crosshead.
Two different methods for establishing valve lash clearance

are described below. Either method can be used. The
torque wrench method has proven to be the most consis-
tent.
• Torque Wrench Method: Use Part No. 3376592,
Inch Pound Torque Wrench. Tighten the adjusting
screw to 1 N•m [6 in-lb] torque.
• Feel Method: Use a nut driver and turn the adjust-
ing screw only until the lever touches the feeler
gauge.
Valve Set — Torque Wrench Method

Hold the torque wrench in a position that allows you to look
in a direct line at the dial. This is to be sure that the dial will
read accurately.
Be sure the parts are in alignment and squeeze the oil out
of the valve and the injector train while tightening the ad-
justing screw.
After loosening the adjusting screw at least 1 revolution,
tighten the adjusting screw again.
NOTE: The feeler gauge must slide backward and for-

ward with only a slight drag.
NOTE: The adjusting screw must not turn when the lock
nut is tightened.
Torque Value:
With Torque Wrench
Adapter, Part No.
ST-669 (1) 45 N•m [35 ft-lb]
Without Adapter 60 N•m [45 ft-lb]
Attempt to insert a feeler gauge that is 0.03 mm [0.001 in]
thicker. The valve lash is not correct when the thicker
gauge will fit.
Repeat the adjustment process until the clearance is cor-
rect on both the intake and the exhaust valves.
Injectors — Setting
Use a dial-type torque wrench to tighten the injector rocker
lever adjusting screw. If the screw chatters during setting,
repair the screw and lever as required.
Hold the torque wrench in a position that allows you to look
in a direct line at the dial. This is to be sure the dial will be
read accurately.
ProCarManuals.com
Be sure the parts are in alignment and squeeze the oil out
of the valve and injector train, while tightening the adjusting
screw.
Loosen the adjusting screw at least 1 revolution.
Tighten the adjusting screw again.
NOTE: The torque wrench must be calibrated, have a
resolution of 0.28 N•m [2.5 in-lb], and have a range of 17
to 23 N•m [150 to 200 in-lb]. Do not use a clicker-type
torque wrench.
Hold the adjusting screw in this position. The adjusting

screw must not turn when the lock nut is tightened.
Tighten the lock nut to the following values:
Torque Value:
With Torque Wrench
Adapter, Part No. ST-
669 (1) 45 N•m [35 ft-lb]
Without Adapter 60 N•m [45 ft-lb]
NOTE: To provide a constant set, lubricate the injector
adjusting screw prior to setting the injectors.
1. Engine firing order 1-5-3-6-2-4

2. Cylinders are numbered from the front gear cover end of the engine.
3. Two crankshaft revolutions are required to adjust all of the valves and the injectors.
4. One pair of valves and one injector are adjusted at each pulley index mark before rotating the engine to the next
index mark.
5. The valves and the injectors on the same cylinder are not adjusted at the same mark.
6. Each cylinder has three rocker levers. The lever nearest to the front of the engine is the exhaust lever.
The following chart is useful for recording values.
NOTE: Refer to Procedure 003–006, Overhead Set (OBC), for value and injector adjustment procedures.
Inspection Report for Valve Lash and Injector Torque
Work Valves Intake Exhaust Reset Crosshead Cylinder Injector Reset
Sequence to be Set (Y/N) (OK/Reset) No. Torque (Y/N)
______ A-5 ______ ______ ______ _______ 4 ______ ______
______ B-3 ______ ______ ______ _______ 1 ______ ______
______ C-6 ______ ______ ______ _______ 5 ______ ______
______ A-2 ______ ______ ______ _______ 3 ______ ______
______ B-4 ______ ______ ______ _______ 6 ______ ______
______ C-1 ______ ______ ______ _______ 2 ______ ______
Customer: ............................................................................................................................................................
ProCarManuals.com
Location: ..............................................................................................................................................................
Unit No. ............................................ Hours: ............................................ Date: ............................................
Job No.: ...............................................................................................................................................................
Engine Model No.: ....................................................... Engine Serial No.: .......................................................
Type of Inspection (Failure, Routine, Complaint):
Inspection Notes: .................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
............................................................................................................................................................................
This page can be copied for your convenience.

NOTE: Do not use gasket cement. It will prevent the gasket

from sealing properly.
Install the rocker lever cover, gasket, and capscrews.
Install the coolant thermostat housing support.

ProCarManuals.com
Conventional Aftercooling
Install the o-rings (19) on the water transfer tube.
Use vegetable oil. Lubricate the o-rings. Install the tube in
the bore of the rocker lever housing.
Align the bore in the thermostat housing support with the
transfer tube. Push the support into position.
NOTE: The outside capscrew holds a clip for the after-

cooler water inlet tube.
Install the four lockwashers and capscrews. Tighten the
capscrews.
Use vegetable oil to lubricate the o-ring. Install a new o-ring

on the aftercooler water supply tube (31).
Install the tube in the bore of the thermostat housing.
Install the retainer clip (7) and capscrew.
NOTE: The retainer clip leg should point towards the ther-
mostat housing.
Torque Value:
Capscrew 20 N•m [15 ft-lb]
Tighten the hose clamps.
Torque Value:
Hose Clamp 6 N•m [50 in-lb]
Attach the support clip to the bracket (34).
Connect the aftercooler coolant return tube (7) and hose(s)

to the aftercooler.
Install the gasket and return tube capscrews.
ProCarManuals.com
Install the vent hose (6).

Connect the coolant temperature sensor wire.
NOTE: If the engine is equipped with an air compressor,
install the air compressor coolant return tube.
Use vegetable oil. Lubricate the o-ring on the bypass tube.

Install the bypass tube.
Install the retainer (9) and capscrew. Tighten the capscrew.
Torque Value:
Torque Value:
Low Temperature Aftercooling

Install the o-rings (19) on the water transfer tube.
Use vegetable oil. Lubricate the o-rings.
Install the tube in the bore of the rocker lever housing.
Align the bore in the thermostat housing support with the
transfer tube. Push the support into position.
NOTE: The outside capscrew holds a clip for the after-

cooler water inlet tube.
Install the four lockwashers and capscrews. Tighten the
capscrews.
ProCarManuals.com

Install the retainer (9) and capscrew.
mostat housing.
Torque Value:
Torque Value:
Use vegetable oil to lubricate the o-ring. Install a new o-ring

on the aftercooler water supply tube (31).
Install the tube in the bore of the thermostat housing.
Install the retainer clip (7) and capscrew.
mostat housing.
Torque Value:
Torque Value:
Attach the support clip to the bracket (34).
Use vegetable oil to lubricate the new o-rings. Install the

o-rings on the aftercooler water inlet and outlet tubes.
Install the tubes.
Install the retainer clips (7) and capscrews.
ProCarManuals.com
Torque Value:
Torque Value:
Attach the support clips to the bracket (34).
Connect the coolant temperature sensor wire (17).
NOTE: Service replacement cam followers are coated with

a heavy preservative to prevent rust. This preservative must
be removed completely with solvent before the parts are
installed on the engine.
CAUTION
The cam follower mounting capscrews are special 12-
point flange heads. Shaft failure will result if standard
capscrews are used.
Use engine oil to lubricate the camshaft and cam followers.
Install the cam follower assembly. The shaft must fit on

both ring dowels.
2 110 N•m [80 ft-lb]
3 165 N•m [120 ft-lb]
CAUTION
The tabs on the cover gasket must be removed before
installation.
Install the gasket, cover, and capscrews.
ProCarManuals.com
Tighten the 14 capscrews in sequence shown.

Install the crankcase vent hose, fuel supply line, and the
wiring harness.
Rail Applications
Install the face seal o-rings.
Install the two scavenging tubes on the fittings of the cam
follower cover.
Rail Applications
Connect the turbocharger drain hose to the scavenge cross.
NOTE: The dipstick tube and fuel filter mounting locations

vary depending on the application of the engine.
Install the dipstick tube.
Tighten the nut 3/4 turn to 1 turn after contact with the
ferrule.
ProCarManuals.com
Install the gasket, filter head and six capscrews.

Oil Transfer Connection Block

Install the lube oil transfer connection block gasket, remove
tab as shown.
Install the lube oil transfer connection block.
Remove the two straight threaded o-ring plugs from the

timing holes in the front cover.
Check the index mark alignment.
CAUTION
Do not use the ‘‘A’’ on the camshaft idler gear for the
accessory drive alignment unless the ‘‘X’’ marks on the
camshaft and the camshaft idler gears are aligned and
centered in the upper timing plug hole. If the ‘‘X’’ marks
are not visible in the upper hole, rotate the engine until
the ‘‘X’’ marks on the camshaft gear and camshaft idler
gear are aligned and centered in the upper timing plug
ProCarManuals.com
hole.
NOTE: Install the accessory drive so that the ‘‘A’’ on the
accessory drive gear is centered in the lower timing plug
hole.
Install the gasket, capscrews, and nut. Tighten the

capscrews.
Install the straight threaded o-ring plugs. Tighten the o-ring

plugs.
Install the accessory drive seal.
NOTE: The keyway seal must be installed before installing

the woodruff key.
ProCarManuals.com
Install the woodruff key.
CAUTION
Use pulley installation tool kit, Part No. 3376326. Insert the
appropriate adapter (7) in the pusher.
step on the shaft.
All QSK19 engines use a light green fuel pump drive cou-
pling.
Install the fuel pump drive coupling (23), gasket, fuel pump,
and four capscrews. Tighten the capscrews.
ProCarManuals.com
Check for the proper installation of the o-rings in both

locations.
Install the fuel pump inlet hose and the fuel supply hose.
Tighten the hoses.
Torque Value:
Fuel Pump Inlet Hose 88 N•m [65 ft-lb]
Fuel Supply Hose 60 N•m [45 ft-lb]
Install the fuel filter head.

Install the two mounting capscrews.
Connect the fuel line to the fuel filter head.
Install a new thread adapter sealing ring supplied with the

new filter.
A fuel-water separator or fuel filter and water separator
combination must be installed.
Apply a light coating of clean engine oil to the surface of the
filter gasket.
Fill the filter with clean fuel.
ProCarManuals.com
Install the filter on the filter head. Turn the filter until the
gasket touches the surface of the filter head.
Tighten the filter an additional 1/2 to 3/4 of a turn after the
gasket touches the filter head surface.
Open the fuel line shutoff valve and check for leaks.
Install the four capscrews to secure the control valve body

assembly and the wire harness and brackets.
Tighten the nut that holds the electrical connection post on

the fuel shutoff valve coil.
Install the electrical connection on the fuel shutoff valve.

Install the nut on the threaded post of the coil.
Use two [3/8-inch] wrenches. Hold the post of the nut firmly
while tightening the connection nut.
ProCarManuals.com
Inspect the actuator and pressure sensor connections for

dirt and debris.
Use dielectric lithium grease, Part No. 3822934, and QDT
contact cleaner, Part No. 3824510. Clean and lubricate the
connections and actuator if cleaning is required.
NOTE: If the electrical connections were not labeled for

identification purposes during disassembly, verify the types
of connections on the wiring diagram.
Connect the actuator and pressure sensor connections.
Connect the fuel supply hose (1), the timing rail pressure
line (2), and the metering rail pressure lines (3) to the
control valve body.
Tighten the fuel supply hose (1).
Tighten the timing pressure (2) and rail pressure lines (3).
Torque Value:
Fuel Supply Hose (1) 61 N•m [45 ft-lb]
Timing and Rail

Pressure Lines (2
and 3) 27 N•m [20 ft-lb]
Use LubriplateT No. 105, or equivalent, to position and

secure the o-rings. Install the o-rings.
ProCarManuals.com
Install the front fuel manifold. Use the sequence illustrated

to tighten the 12 capscrews.
Torque Value: 9.6 N•m [85 in-lb]
Repeat this process for the installation of the rear fuel
manifold.
On engines equipped with an air compressor, install the air

inlet connection hose, and new gasket.
Install the engine wiring harness and brackets.
Fuel Tank-To-Fuel Filter

Install and tighten the fuel inlet line.
ProCarManuals.com
Fuel Rail Supply Line

Fuel Timing Supply Line
Loosely assemble the fuel tubes and clamps.
NOTE: It is a good service practice to use two wrenches

when tightening the fuel fittings.
Support the fitting. Use a crowfoot wrench and a torque
wrench. Tighten the fuel tube nut.
Tighten the fuel tube clamps.

On engines equipped with an air compressor, install the air

compressor air inlet connection with a new hose and gas-
ket.
Torque Value:
Flange Capscrew: 4 N•m [35 in-lb]
Torque Value:
Clamp: 6 N•m [50 in-lb]
ProCarManuals.com
Fuel Control Supply Lines

Install new o-rings on the control valve body inlet fitting and
the fuel pump outlet fitting. Be sure the o-ring is installed
properly.
Install and tighten the fuel control valve supply hose.

Fuel Inlet Line

Install new o-rings on the fuel pump inlet fitting and fuel
filter head outlet fitting. Check for proper o-ring installation.
Install the hose at the fuel pump inlet and fuel filter head
outlet fitting.
Tighten the hose.
ProCarManuals.com
Install the bolt seals in the aftercooler housing.
NOTE: Use guide studs long enough to protrude beyond

the installed part.
Install 12 guide studs in the upper row of capscrew holes
in the cylinder heads.
Install the gaskets on the studs with the raised bead on the
gasket toward the cylinder head.
CAUTION
component.
Install the aftercooler and the bottom row of capscrews.
Tighten the capscrews only enough to hold the part.
Remove the guide studs and install the top row of
capscrews.
Use the sequence shown, and the steps and values indi-
cated below to tighten the capscrews.
2 45 N•m [35 ft-lb]
ProCarManuals.com
Rail Applications
Install the intake manifold and 24 capscrews. Tighten the
24 capscrews in the sequence shown.
Rail Applications
Install the turbocharger drain line to the turbocharger.
Rail Applications
Install the face seal o-ring.
Install the turbocharger drain line to scavenge cross.
Rail Applications
Install hose and tighten hose clamp.
ProCarManuals.com
Connect the inlet hose. Tighten the clamps.

Torque Value 6 N•m [50 in-lb]
Connect the water outlet hose (8). Tighten the clamps.

Install the coolant vent and tighten.
Install two guide studs. Put the gasket and housing into
position.
Install, but do not tighten, capscrews.
CAUTION
Do not tighten the capscrews until the oil cooler cover
or torque converter cooler cover is installed.
Install the capscrews as shown.
CAUTION
The two capscrew holes marked ‘‘X’’ align with cylinder
ProCarManuals.com
head capscrews. The cylinder head capscrews will be

damaged if the cooler housing capscrews are too long.
Oil Cooler Capscrew Lengths
Illustration Callout No. Without Oil Filter
1 1-1/4 in
2 1-3/4 in
3 1-5/8 in
4 1-3/4 in
5 1-5/8 in
NOTE: Remove the plastic shipping plugs from the new oil
cooler elements.
Install the gaskets, oil cooler elements, and capscrews.
Install the oil cooler cover.
Install the elements.

Tighten the self-locking nuts.
Use new o-rings. Lubricate the o-rings with vegetable oil.
Install the o-rings on the cooler elements.
ProCarManuals.com
CAUTION
component.
Use two [3/8-16 x 12 inch] guide studs to support the
housing during installation.
Install the gasket and housing.
Install the capscrews in the bottom row of holes on the
housing. These capscrews are all 101.6 mm [4 in] long.
NOTE: The length and location of all the capscrews on the

torque converter cooler and cover are shown. Be sure the
capscrews are the correct length.
Do not tighten any of the capscrews until all of them have
been installed.
NOTE: Be sure the capscrews are the correct length.

Use vegetable oil to lubricate the o-rings on the cooler
element and the bores in the cover.
Install the gasket and cover. Push the cover over the o-rings
until the cover is against the housing.
Install the remaining capscrews.
Tighten the capscrews in the sequence shown.

ProCarManuals.com
Use vegetable oil. Lubricate the o-rings (13).

Install the transfer tube in the water pump outlet connec-
tion.
Install the water pump outlet connection, gasket, and
capscrews.
Connect the aftercooler supply hose to the water pump

outlet connection.
Tighten the clamps.
Use vegetable oil. Lubricate the o-ring on the water bypass

tube.
Tighten the capscrew and hose clamp.
Torque Value:
Clamp 5.6 N•m [50 in-lb]
Connect the torque converter oil hoses to the torque con-

verter cooler.
ProCarManuals.com
Install the oil cooler cover and new gasket. Use several
capscrews to secure the cover in position, but do not tighten
the capscrews.
Install the capscrews as shown.

Tighten the capscrews to the values specified and in the

sequence shown.
Use vegetable oil. Lubricate the o-rings (13).

tion.
capscrews.
ProCarManuals.com

outlet connection.
Tighten the clamps.

Tighten the capscrew and the hose clamps.
Torque Value:
Torque Value:
CAUTION
Do not use gasket cement or the gasket will fail.
Install the guide studs used during removal.
Use contact adhesive and attach the gasket on the cylinder
head exhaust ports.
Install the exhaust manifold.
Apply an antiseize compound on the capscrew threads.

Remove the two guide studs (12) and install the remaining
capscrews.
ProCarManuals.com
Tighten the capscrews in the sequence shown.

Marine Applications
NOTE: Do not rip, tear, or damage the insulation on the
exhaust manifold.
Install the heat shield.
Install the 7 mounting capscrews.
Holset turbocharger(s) are used on the QSK19 engine.

Refer to the data tag on the turbocharger to determine the
model.
NOTE: The name is also cast on the housing of a
turbocharger.
NOTE: All turbocharger fittings are the flat face o-ring type
fittings. Be sure the o-ring is in place before attaching the
hose(s) to the fittings.
The Holset turbocharger uses a [9/16-18 UNF], straight
thread, o-ring type oil supply fitting.
ProCarManuals.com
Apply an antiseize compound to the mounting capscrews.

Install the gasket.
NOTE: The word “OUT” must be positioned toward the
turbocharger or the raised gasket bead.
Install the turbocharger, washers, and nuts.
Position the turbocharger drain tube. The drain tube must

be within 35 degrees of vertical. Turn the bearing housing
to align the tube, if necessary.
NOTE: The turbocharger uses capscrews to attach the
bearing housing to the turbine housing.
Bearing Housing Adjustment

Bend the lockplate off the capscrew heads.
Rotate the bearing housing. Align the drain tube and the
capscrew holes.
Install the lockplates and capscrews.

Bend the lockplate tabs over the capscrews.
ProCarManuals.com
CAUTION
These parts are a safety-related item. Be sure the parts
are clamped correctly to prevent fretting.
Install the oil drain tube and gasket.
Tighten drain hose swivel to oil pan adapter.
Pour clean engine oil into the turbocharger oil supply fit-
ting.
Turbocharger Oil Supply
50 to 60 cc
[2.0 to 3.0 oz.]
Connect the oil supply hose.

Tighten the hose fitting.
Connect the coolant supply hose and the coolant return

hose to the turbocharger.
Tighten the hose fittings.
ProCarManuals.com
Check the air crossover-to-turbocharger alignment.

• Install the air crossover on the aftercooler.
• Look at the alignment between the crossover and
the turbocharger compressor outlet.
• Remove the crossover and proceed with the assem-
bly if the alignment is correct.
• Proceed to the next step to adjust the compressor
housing if the alignment is not correct.
To adjust the turbocharger compressor housing alignment:

Loosen the V-band clamp.
Turn the compressor housing to the correct alignment.
Tighten the clamp.
Tap the clamp with a mallet and tighten the clamp again.
Install the hose and two hose clamps on the air crossover
tube.
Install the air crossover. Slide the hose down and over the
turbocharger outlet. Install the gasket and capscrews.
Use the sequence illustrated.

Torque Value 45 N•m [35 ft-lb]
Tighten the clamps.
ProCarManuals.com
Connect the inlet piping to the turbocharger.

Tighten the clamps.
Connect the exhaust piping to the turbocharger.

Tighten the V-band clamp.
Install the belt tensioner on the idler arm.

Install the idler arm assembly and capscrews (2).

Install the belt tensioning nut (1). Do not tighten the nut.
ProCarManuals.com
CAUTION
This assembly weighs more than 23 kg [50 lb] . To avoid
Install the fan hub, the eight washers and nuts.
Tighten the fan hub nuts.
Install the fan belt.

Install the fan.
Tighten the belt tensioning nut.
Install the inlet connection (1), gasket, and capscrews.

NOTE: Do not tighten the support bracket until the water
pump is assembled to the engine. Use a heavy, plain washer
on the capscrew that attaches through the slotted hole.
Install the support bracket (2).
NOTE: Failure of the water pump drive shaft will result

when the wrong shaft is installed.
Use shaft (1) with cast iron impeller pumps (Marine appli-
cations). Use shaft (2) with phenolic (plastic) impeller
pumps.
NOTE: Install the shaft with the oil hole at the side of the
shaft toward the water pump.
ProCarManuals.com
Use engine oil and lubricate the drive shaft (14). Install the
shaft in the splined hole in the water pump drive.
NOTE: Do not tighten the capscrews and nut until the
support bracket is aligned with the cylinder block.
Install the gasket and water pump. Install three capscrews
and nuts.
Tighten the capscrews and nuts.
The support bracket must be flat against the water pump

and the cylinder block. Align the bracket before tightening
the capscrews.
Install the capscrew through the bracket.
Check the alignment between the support bracket and the
water pump. Loosen the capscrew and adjust if necessary.
Tighten the capscrews holding the support bracket to the
water pump.
Use vegetable oil and lubricate the o-rings (13).

tion.
capscrews.

outlet connection.
Tighten the clamps.
ProCarManuals.com
Install the bypass connection gasket.

Use vegetable oil and lubricate the o-ring on the bypass
tube. Install the bypass tube.
Install the retainer and capscrew.
Torque Value:
Use engine oil and lubricate the seal on the filter.

NOTE: Do not allow oil to get in the filter. It will adversely
affect the SCA.
Install the coolant filter. Turn the filter until the seal touches
the filter head. Turn an additional 1/2 to 3/4 of a turn after
contact.
Turn the valve to the ON position.

ProCarManuals.com
Lubricate the shaft with engine oil. Install the pulley and nut
on the alternator shaft.
Tighten the nut.
The belt must be adjusted before the capscrews are tight-

ened.
NOTE: The end of the adjusting link with the largest area
at the capscrew hole must be nearest to the alternator.
Install the alternator and the adjusting link as shown.
CAUTION
Do not attempt to pry the belt on the pulley to avoid
damage to pulley and belt.
Install the belt. Turn the adjusting screw counterclockwise
to shorten the link if necessary.
Turn the adjusting screw clockwise to tighten the belt.

Tighten the belt.
Belt Tension 670 N [150 lbf]
Use the (Burroughs) belt tension gauge, Part No. ST-1138,
to check the belt tension.
ProCarManuals.com

Tighten the jam nuts on the adjusting screw.
Tighten the adjusting link and alternator mounting
capscrews.
Torque Value:
Jam Nuts 55 N•m [40 ft-lb]
Alternator Mounting
Capscrews 55 N•m [40 ft-lb]
Connect the wiring to the alternator.

WARNING
Always connect the negative (-) cable last to avoid sparks
that can ignite explosive battery gases.
WARNING
Connect the batteries.
NOTE: Not all engines use spacers.

NOTE: The wet type flywheel housing requires gaskets for
the starting motor.
Install any spacer or gaskets.
Install the starting motor and capscrews.
Use the following to tighten the capscrews.
Torque Value:
W/Cast Iron Flywheel
Housing 215 N•m [160 ft-lb]
W/Aluminum Fly-
wheel Housing 195 N•m [145 ft-lb]
WARNING
Always connect the negative (-) cable last to avoid sparks
that can ignite explosive battery gases.
WARNING
ProCarManuals.com
Install the electrical connections to the starting motor.

Connect the batteries.
NOTES
ProCarManuals.com
Section 1 - Cylinder Block - Group 01 Page 1-a
Section 1 - Cylinder Block - Group 01

Section Contents
Page
Bearings, Connecting Rod .............................................................................................................................. 1-5
Clean ........................................................................................................................................................... 1-5
Inspect for Reuse ......................................................................................................................................... 1-5
Bearings, Main ................................................................................................................................................. 1-5
Clean ........................................................................................................................................................... 1-5
Measure ....................................................................................................................................................... 1-6
Bearings, Thrust .............................................................................................................................................. 1-6
Assemble ...................................................................................................................................................... 1-7
Camshaft.......................................................................................................................................................... 1-7
Clean ........................................................................................................................................................... 1-7
Magnetic Crack Inspect ................................................................................................................................ 1-8
Camshaft Bushings........................................................................................................................................ 1-15
Inspect for Reuse ....................................................................................................................................... 1-16
Install ......................................................................................................................................................... 1-16
Remove ...................................................................................................................................................... 1-15
ProCarManuals.com
Camshaft Gear (Camshaft Removed) ............................................................................................................ 1-10

Install ......................................................................................................................................................... 1-14
Magnetic Crack Inspect .............................................................................................................................. 1-12
Remove ...................................................................................................................................................... 1-10
Connecting Rod ............................................................................................................................................. 1-18
Clean ......................................................................................................................................................... 1-18
Crankshaft ...................................................................................................................................................... 1-25
Bend and Twist Inspect .............................................................................................................................. 1-29
Clean ......................................................................................................................................................... 1-25
Crankshaft Gear, Front (Crankshaft Installed)............................................................................................... 1-34
Install ......................................................................................................................................................... 1-35
Remove ...................................................................................................................................................... 1-34
Crankshaft Gear, Rear (Crankshaft Installed) ................................................................................................ 1-36
Install .......................................................................................................................................................... 1-36
Crankshaft Pulley ........................................................................................................................................... 1-36
Clean ......................................................................................................................................................... 1-36
Cylinder Block................................................................................................................................................ 1-38
Clean ......................................................................................................................................................... 1-39
Worksheet .................................................................................................................................................. 1-38
Cylinder Block - General Information.............................................................................................................. 1-1
Cylinder Block and Liner Seats..................................................................................................................... 1-47
General Information .................................................................................................................................... 1-47
Leak Test ..................................................................................................................................................... 1-51
Measure ..................................................................................................................................................... 1-49
Cylinder Block Counterbore .......................................................................................................................... 1-65
Machine ..................................................................................................................................................... 1-65
Page 1-b Section 1 - Cylinder Block - Group 01
Page
Cylinder Liner................................................................................................................................................. 1-51
Clean ......................................................................................................................................................... 1-51
Cylinder Liner Protrusion .............................................................................................................................. 1-79
Adjust ......................................................................................................................................................... 1-79
Gear Cover Accessory Drive Bushing ........................................................................................................... 1-80
Install ......................................................................................................................................................... 1-80
Remove ...................................................................................................................................................... 1-80
Gear Cover, Front........................................................................................................................................... 1-55
Clean ......................................................................................................................................................... 1-55
Measure ..................................................................................................................................................... 1-57
Gear Cover Spacer Plate ............................................................................................................................... 1-55
Clean ......................................................................................................................................................... 1-55
Idler Gear, Camshaft ...................................................................................................................................... 1-57
Clean ......................................................................................................................................................... 1-57
Idler Gear, Hydraulic Pump............................................................................................................................ 1-59
Clean ......................................................................................................................................................... 1-59
ProCarManuals.com
Idler Gear, Water Pump.................................................................................................................................. 1-60

Clean ......................................................................................................................................................... 1-60
Piston ............................................................................................................................................................. 1-60
Clean ......................................................................................................................................................... 1-60
Service Tools ................................................................................................................................................... 1-2
Cylinder Block............................................................................................................................................... 1-2
Vibration Damper ........................................................................................................................................... 1-63
Clean ......................................................................................................................................................... 1-63
Cylinder Block - General Information
Section 1 - Cylinder Block - Group 01 Page 1-1
Cylinder Block - General Information

General Information
The barring mechanism is inside the front cover. The front cover must be removed from the engine to service or rebuild
the barring mechanism.
This barring mechanism contains a spring loaded worm gear. The worm gear engages the camshaft gear when the
barring shaft is pushed in the front cover and turned in a counterclockwise direction. The barring mechanism will ONLY
turn the engine in the direction of normal rotation. Turn the barring shaft in a clockwise direction to disengage the worm
gear. If the worm gear remains engaged accidently during the engine START, the engine rotation will disengage the
parts without damage.
The static injection timing is adjusted by using different camshaft keys. The selection of a key will change the position
of the camshaft lobes in relation to the timing mark on the camshaft gear. The gear must be removed to change the
injection timing.
The camshaft end clearance is determined by the clearance between the camshaft and the thrust plate. The camshaft
gear must be removed to adjust the camshaft end clearance.
NOTE: The camshaft does not have to be removed to remove the camshaft gear. Use the Camshaft gear puller, Part
No. 3376400.
Camshaft’s that are damaged or worn on the injector or the valve lobes must be replaced. Cummins Engine Co., Inc.
does not recommend the grinding of camshaft lobes.
ProCarManuals.com
The crankshaft uses forged counterweights.

Oversize main bearings and thrust bearings are available for service. Cummins Engine Co., Inc.. recommends
regrinding ALL of the main or the connecting rod journals when ONE requires regrinding
The vibration damper controls the twisting or torsional vibration of the crankshaft. A vibration damper is engineered
for use on a specific engine model.
It is not economical to repair a vibration damper in the field. Install a new or a rebuilt vibration damper if the inspection
indicates that a damper is defective.
The viscous vibration damper has a limited service life. The damper must be replaced.
Service Tools
Page 1-2 Section 1 - Cylinder Block - Group 01
Service Tools
Cylinder Block

Measure cylinder liner protrusion and cylinder liner counterbore
ledge angle.
3823495
ProCarManuals.com
Puller
Remove the alternator and accessory drive pulleys.
ST-647
Dowel Pin Extractor

Remove dowel pins and crosshead guides.
ST-1134
Drill Ream Fixture

ST-1232
priate drill/ream bushing set.
Piston Ring Expander

Designed to install piston rings on the piston without damaging
or distorting the rings.
ST-1269
Connecting Rod Guide Pins

Special nylon pins used to protect the crankshaft journal by
guiding the connecting rod during installation or removal.
3375098
Service Tools

Liner Installation Tool
Install cylinder liner in engine.
3375422
Crack Detection Kit

Check for cracks in any engine component. Contains cleaner,
developer, and penetrant.
3375432
Injection Timing Tool

Check injection timing. The timing fixture is designed to deter-
mine the push tube travel in relation to the piston travel.
3824942
ProCarManuals.com
Universal Timing Tool Adaptor Kit

This kit includes the hardware needed to upfit the Universal
Injector Timing Fixture, Part No. 3823451 to the QSK19 engine.
3824946

Remove small bushings, oil seals, and bearings.
3375784
Puller Assembly
Remove the crankshaft gear from the crankshaft. Use with Part
No. 3375835 Puller Jaw.
3375834
Universal Liner Puller

Remove cylinder liner from engine.
3376015

Install the alternator and accessory drive pulleys.
3376326
Service Tools

Cummins Sealant
Used to prevent coolant or oil leaks. This is one part Room
Temperature Vulcanizing (RTV) silicone rubber, adhesive, and
3823494
sealant material having high heat and oil resistance, and low
compression rate.
Camshaft Bushing Tool Hydraulic Actuator Kit

Hydraulic ram provides the force to install/remove cam bushings
when used with installation/removal kit.
3823621
Camshaft Bushing Installation/Removal Kit

Used with the Part No. 3823621 Camshaft Bushing Hydraulic
Actuator Kit to remove the camshaft bushing.
3824863
ProCarManuals.com
Camshaft Pilot
Install camshaft without damaging the camshaft bushings or
camshaft.
3825150
Camshaft Gear Puller Kit

Remove camshaft gear from camshaft without removing cam-
shaft from engine.
3824900
Main Bearing Roll-out Tool

Used to remove and install upper main bearing shell.
3823818
Bearings, Connecting Rod (001-005)
Bearings, Connecting Rod (001-005)

Clean
The bearings must be marked for location as they are
removed for future identification. Each bearing must be
installed in its original location if the bearing is installed
again.
WARNING
When using solvents, acids or alkaline materials for
cleaning, follow the manufacture’s recommendations
for use. Wear goggles and protective clothing to avoid
personal injury.
Use solvent. Clean the bearings.
Inspect for Reuse

Use a ball-end micrometer.
Measure the thickness of the bearing in the wear location.
Replace the bearing when it is not within specifications.
Connecting Rod Bearing Thickness
ProCarManuals.com
Standard or Oversize (OS)

Size mm in
Standard 3.106 MIN 0.1223
3.157 MAX 0.1243
0.010 (OS) 3.233 MIN 0.1273
3.284 MAX 0.1293
0.020 (OS) 3.360 MIN 0.1323
3.411 MAX 0.1343
0.030 (OS) 3.487 MIN 0.1373
3.538 MAX 0.1393
0.040 (OS) 3.614 MIN 0.1423
3.665 MAX 0.1443
Bearings, Main (001-006)

Clean
CAUTION
Do not use a scraper or a wire brush.
NOTE: Be sure the bearings are marked for location. The
bearings must be installed in the original location after
rebuild.
Use a lint-free cloth. Clean the crankshaft journals, and
connecting rods. Check the crankshaft journal for damage.
Use solvent. Clean the bearings. Dry with compressed air.
Bearings, Thrust (001-007)
Inspect for Reuse

Use a ball-end micrometer. Measure the bearing thickness
at the wear location. The bearing must be replaced if it is
not within specifications.
Main Bearing Thickness
Size mm in
4.336 MAX 0.1707
0.010 (OS) 4.407 MIN 0.1735
4.463 MAX 0.1757
0.020 (OS) 4.534 MIN 0.1785
4.590 MAX 0.1807
0.030 (OS) 4.661 MIN 0.1835
4.717 MAX 0.1857
0.040 (OS) 4.788 MIN 0.1885
4.844 MAX 0.1907
Measure
Measure the thrust bearing thickness. Measure the areas
that shine. The shine indicates where the crankshaft has
contacted the bearing.
ProCarManuals.com
Thrust Bearing Thickness

mm in
3.90 MAX 0.1535
0.010 (OS) 4.08 MIN 0.1605
4.15 MAX 0.1635
0.020 (OS) 4.33 MIN 0.1705
4.41 MAX 0.1735
Bearings, Thrust (001-007)

Inspect for Reuse
Thrust bearings are available in three sizes: [STD, 0.010,
0.020] OS. The upper and lower thrust bearings must be
the same size. The front and rear can be different sizes.
Use the same size as those removed. The crankshaft will
be marked on a counterweight adjacent to the thrust lo-
cation if the thrust flange has been machined for oversize
thrust bearings.
Camshaft (001-008)
Assemble
Camshaft (001-008)
Clean
Use solvent and compressed air. Clean the camshaft.
After the camshaft has been cleaned, do not touch the

machined surfaces with bare hands. This will cause rust to
form. Lubricate the camshaft with clean 15W-40 oil before
handling.
ProCarManuals.com
Inspect for Reuse

CAUTION
Do not repair the camshaft by grinding the valve or the
injector lobes.
Inspect the camshaft.
Check the valve and the injector lobes for damage.
If the camshaft is damaged, it must be replaced.
Measure each of the seven bushing journals.
Measure the O.D.
Camshaft Bushing Journal O.D.

mm in
76.07 MIN 2.995
76.12 MAX 2.997
If the O.D. is not within specifications, the camshaft must
be replaced.
Camshaft (001-008)
Inspect the camshaft thrust bearing. .
Visually inspect the amount of copper exposure on the

camshaft bushing. If it extends more than 180 degrees
around the bushing, the bushing must be replaced.
Measure the I.D.
Camshaft Bushing I.D.

mm in
82.550 MIN 3.2500
82.640 MAX 2.2535
ProCarManuals.com
If the bushing is not with specifications, the bushing must

be replaced.
If camshaft requires replacement, inspect the camshaft

gear for reuse. Refer to Procedure No. 001-013.
Magnetic Crack Inspect

The gear and the thrust plate must be removed before
performing this check.
Use a magnetic particle testing machine. Use the head
shot method.
Adjust the machine to 2000 ampere D.C. or rectified A.C.
Use the continuous method. Do not wet more than one-
third of the camshaft at a time.
Check the camshaft for cracks.
Camshaft (001-008)
CAUTION
Use the coil shot method. Use a coil that is a minimum
of 305 mm [12 in].
Apply coil shot. Use the continuous method.
Amperage
(Ampere Turns)
Min 3600 D.C. or Rectified A.C.
Max 4000 D.C. or Rectified A.C.
NOTE: Ampere turn is an electrical current of one ampere
flowing through the coil, multiplied by the number of turns
in the coil.
Check the camshaft for cracks.
Limits of Acceptance-Bearing Journal

Do not use the camshaft if,
• there are more than four open indications in an axial
direction on one of the bearing journals.
• more than one-half of the open indications extend
more than half the distance across the bearing jour-
nals.
• there is an open indication in a circumferential di-
ProCarManuals.com
rection.
NOTE: The camshaft can be used if there are indications
below the surface.
Camshaft Gear (Camshaft Removed) (001-013)
Limits of Acceptance- Open Indications

An open indication is visible to the eye after the suspension
has been removed. An indication below the surface is not
visible to the eye after the suspension has been removed.
Do not use the camshaft if:
• There is an indication in a circumferential direction.
• There is an indication in the black or shaded areas
shown.
• There is an indication that is longer than 6 mm [1/4
inch].
• There is an indication that is closer than 5 mm [3/16
inch] from the edge.
• There are more than two indications on one of the
lobes.
Limits of Acceptance- Indications Below the Surface
Do not use the camshaft if:
• There are more than two indications in the shaded
area shown.
• There is an indication in the shaded area shown that
is longer than 16 mm [5/8 inch].
• There are more than three indications in the white
area shown.
• There is an indication in the black area on the in-
ProCarManuals.com
jector lobe (1).

• There are more than two indications in the black
area on the valve lobe (2).
• There is an indication in the black area on the valve
lobe that is longer than 3 mm [1/8 inch].
CAUTION
The camshaft must be demagnetized completely and
cleaned thoroughly. Small metal particles will cause
engine damage.
Demagnetize the camshaft.
WARNING
When using solvents, acids, or alkaline materials for
cleaning, follow the manufacturer’s recommendations
personal injury.
Use solvent or steam to clean the camshaft.
Camshaft Gear (Camshaft Removed)

(001-013)
Remove
Use a camshaft gear puller, Part No. 3824900, to remove
camshaft gear.
Attach the puller to the gear. Remove the gear.
Remove the puller.
NOTE: Camshaft keys area available in different sizes

(amount of offset). The injection timing is controlled by:
• The selection of the camshaft key.
• The direction of the key offset when compared to the
camshaft gear rotation.
• The amount of offset.
Check and record the direction of the key offset when
compared to the camshaft gear rotation (same or opposite).
Remove the key.
The camshaft key provides a means of indexing the cam-

shaft with the gear.
Offset keys allow the camshaft profile to be rotated slightly
while the gear train timing remains the same.
The more the top of the offset is moved in the direction of
the camshaft normal rotation, the more the injection timing
will be retarded. The push rod travel numerical value will
increase.
ProCarManuals.com
NOTE: This applies to ALL Cummins engines.

NOTE: The direction of normal rotation on a QSK19 engine
crankshaft is clockwise as viewed from the front of the
engine.
Inspect for Reuse

Inspect the camshaft and camshaft gear for reuse. Check
for fretting damage. The camshaft must be replaced if the
fretting damage is more than 3 mm [1/8 inch] wide.
Measure the O.D. of the camshaft.
Camshaft O.D. (Gear Location)

mm in
57.200 MIN 2.2520
57.210 MAX 2.2525
Visually inspect the camshaft. Refer to Procedure No.

001-008.
Visually inspect the camshaft gear for cracks, chipped or

broken teeth.
Visually inspect the bore of the gear for fretting or burrs.
Measure the I.D.
Camshaft Gear I.D.

mm in
57.200 MIN 2.2520
57.210 MAX 2.2525
The gear must be replaced if the I.D. is not within
specification.
Visually inspect the thrust bearing for damage.

Measure the thickness.

mm in
9.12 MIN 0.359
9.44 MAX 0.372
ProCarManuals.com

CAUTION
Use a copper braid contact that has neoprene covers to
avoid burning the teeth of the gear.
CAUTION
If the gear contains a keyway, position the gear so that
the keyway points toward one of the contacts when
checking.
Use a magnetic particle testing machine.
Use the residual method to apply head shot amperage.
Adjust the amperage to the specified value.
Gear O.D. Amperage
D.C.
Less than 101 mm [4 inch] 1000
101 mm to 203 mm [4 inch to 8 inch] 1500
Greater than 203 mm [8 inch] 2000
Check the gear for cracks.
CAUTION
the keyway points toward the coil.
Use the residual method. Apply coil shot amperage.
Adjust the amperage to the specified value.
Gear O.D. Ampere
Turns
Greater than 203 mm [8 inch] 8000
in the coil.
Limits of Acceptance - on Machined Surfaces

An open indication is visible to the eye after the wetting
operation has been completed. An indication below the
surface is not visible to the eye after the wetting operation
has been completed. An indication below the surface can
ProCarManuals.com
be seen with the use of the ultraviolet light that is part of the
machine.
Do not use the gear if:
• There is an open indication.
• There is an indication below the surface that is in the
shaded area as shown.
• There is an indication below the surface that is longer
than 6 mm [1/4-in].
Limits of Acceptance - on Forged Surfaces

• There is an open indication that is in a circumfer-
ential direction.
• There is an open indication that is longer than 9.5
mm [3/8-in].
shaded area.
An indication below the surface in a radial direction is
acceptable (OK) if it is in the area that is not shaded.
WARNING
personal injury.
CAUTION
The gear must be demagnetized completely and cleaned
thoroughly. Any small metal particles will cause engine
damage.
Demagnetize the gear.
ProCarManuals.com
Use solvent and clean the gear.

Install
NOTE: The camshaft gear must be removed to adjust the
injection timing. If the camshaft was replaced, do not in-
stall the camshaft gear until the injection timing has been
verified.
Use a slip-fit gear to adjust injection timing. Refer to Pro-
cedure No. 006-025.
The following table lists the recommended camshaft key for
each timing code. Machining tolerances on the camshaft
and the gear can cause the injection timing not to be within
specifications. If the timing is not within specifications,
refer to Section 0 for instructions to choose an alternate
camshaft key.
The amount of offset is based @ 5.1613 mm (0.2032 inch)
of piston travel.
Timing Code Camshaft Amount of Offset
Key
JF 216294 0.279 Inj.

KG S-302 0.320 Inj.
Camshaft Bushings (001-010)
WARNING
burns.
CAUTION
CAUTION
Use an oven with the temperature adjusted to 235° C [450°
F]. Heat the gear in the oven for a minimum of one hour
but not more than a maximum of six hours. The I.D. of the
gear will become larger and will simplify the installation.
NOTE: The timing marks must be visible on the front of the

gear after it is installed. The keyway in the gear must be
aligned with the key.
Install the thrust plate. Install the camshaft gear.
CAUTION
Allow the gear to air cool. Do not use water or oil to
ProCarManuals.com
reduce the cooling time. It will cause the gear to crack.
Use a feeler gauge. Measure the camshaft thrust clear-

ance.
Camshaft to Camshaft Gear Clearance

mm in
0.15 MIN 0.006
0.33 MAX 0.013
If the clearance is not within specification the gear must be
removed.

Remove
Use hydraulic actuator kit, Part No. 3823621, and camshaft
bushing installation/removal kit, Part No. 3162228, to re-
move the camshaft bushings.
Remove the camshaft bushings.
Inspect for Reuse

Inspect the camshaft bores in the block for reuse. Use an
emery cloth to remove any burrs and sharp edges from the
bore.
Measure the I.D.
Camshaft Bushing Bore in the Block

mm in
ProCarManuals.com
88.989 MIN 3.5035

89.015 MAX 3.5045
If the I.D. is not within specifications, install a repair sleeve.
Visually inspect the amount of copper exposure on the

camshaft bushing. If it extends more than 180 degrees
around the bushing, the bushing must be replaced.
Measure the I.D.
Camshaft Bushing I.D.

mm in
82.550 MIN 3.2500
82.640 MAX 2.2535
If the bushing is not within specifications, the bushing
must be replaced.
Install
Align the oil holes in the bushing with the oil drilling in the
block.
NOTE: The notch in the bushing must be positioned toward
the front of the block.
CAUTION
Clean the oil groove in the back of the camshaft bush-
ing to prevent contamination of the lubrication system.
Use the camshaft bushing driver assembly, Part No.
3376637, and the specified engine kit (mandrel). Install the
bushing until the edge of the groove on the back (O.D.) is
even with the edge of the block.
Clean the bushing O.D. Remove any metal shavings from
the oil groove.
CAUTION
Be sure that the front bushing is below the surface of
the block.
Install the bushing until the oil holes are aligned.
ProCarManuals.com
Use a 7 mm [1/4 inch] allen wrench. Check the alignment

of the bushing oil holes.
There are three holes in each bushing. All holes must be
aligned except on the front bushing.
NOTE: There is no drilling to align with the upper holes on
the front bushing.
Connecting Rod (001-014)

Clean
WARNING
personal injury.
CAUTION
The number on the connecting rod must be the same
as the number on the rod cap. NEVER assemble a new
cap to an old rod or an old cap to a new rod.
Remove the capscrews, washers, and the cap from the rod.
Use solvent. Clean the parts.
Inspect for Reuse

CAUTION
The connecting rod and connecting rod cap must be
replaced as an assembly if any fretting damage is vis-
ProCarManuals.com
ible on either piece.

Visually inspect the rod caps, connecting rod bearing
saddles, and capscrews for nicks, cracks, burrs, scratches
or fretting.
Check the threads of the connecting rod capscrew for

damage. Check under the capscrew head for cracks.
Measure the connecting rod capscrew
Capscrew Length (1)

mm in
117.09 MIN 4.610
117.86 MAX 4.640
Capscrew O.D. (2)

mm in
15.26 MIN 0.601
15.37 MAX 0.605
Capscrew O.D. (3)

mm in
17.35 MIN 0.683
17.45 MAX 0.687
NOTE: The capscrews must be replaced if not within
specification.
Visually inspect the bearing seating surface for nicks or

burrs. If it is not possible to remove any nicks or burrs with
a fine crocus cloth, the rod must be replaced.
Measure the connecting rod wrist pin bearing I.D.
Connecting Rod Wrist Pin Bearing I.D.

mm in
60.99 MIN 2.4010
61.02 MAX 2.4025
The bushing must be precision machined after installation.
If machining capability is available, the bushing can be
replaced. Refer to the Alternative Repair Manual, Bulletin
ProCarManuals.com
No. 3379035.
CAUTION
Use a vise with brass jaws to hold the rod. Notches,
scratches, or dents in the I-beam area will cause engine
failure.
CAUTION
The number on the connecting rod must be the same
as the number on the rod cap. Never assemble a new
cap to a used rod or a used cap to a new rod.
CAUTION
The connecting rod must be assembled with the
capscrews tightened to specifications before stamping
the cylinder identification number on the rod. Always
stamp a new connecting rod with the cylinder number
of the rod being replaced.
Use engine oil. Lubricate the connecting rod capscrews.
Assemble the rod, cap, washers, and the capscrews.
Tighten the capscrews in the following sequence:
Connecting Rod Capscrew Torque Value Sequence
Step 1. 100 N•m [ 75 ft-lb]
ProCarManuals.com
Step 2. 200 N•m [ 150 ft-lb]

Step 3. 290 N•m [ 250 ft-lb]
Step 4. Loosen both
capscrews. mm [ in]
Step 5. 100 N•m [ 75 ft-lb]
Step 6. 200 N•m [ 150 ft-lb]
Step 7. 290 N•m [ 250 ft-lb]
Use a dial bore indicator to measure the I.D. within a 20°

arc from each side of the parting line.
Measure the I.D. at 90° from the parting line.
Connecting Rod Bearing Bore I.D.

mm in
107.995 MIN 4.2518
108.005 MAX 4.2522
If any of the three measurements are not within specifi-
cations, the rod must be replaced or repaired.
CAUTION
The rod cap must be installed and torqued to specifi-
cation or the measurements will be wrong.
A connecting rod of known length, bend, and twist, called
a master rod, is required to calibrate the fixture. A new
connecting rod that the distance from the center of the
crank pin to the center of the piston pin end to the center
pin end (rod length) is known, can also be used.
Calibrate the Checking Fixture
Install the appropriate mandrel in the piston pin end of the
master connecting rod.
NOTE: Be sure the locating pin in the mandrel for the crank
pin end is touching the rod cap directly opposite the beam
of the rod.
Install the mandrel in the crank pin bore of the master rod.
tighten the mandrel so that it is centered in the bore
correctly.
Install the master rod in the checking fixture.

Loosen the knob and move the indicator bracket until both
ProCarManuals.com
indicators touch the top of the piston pin end mandrel.

Move the bracket toward the mandrel until the indicator
needles have moved approximately 0.25 mm [0.010 inch].
Turn the knob to tighten the bracket.
Adjust the indicator needles to “0”. Move the master rod in
and out to confirm the “0”.
Remove the master rod from the fixture.

Rotate the rod 180 degrees horizontally and install it in the
checking fixture.
Be sure the indicators are at the “0” setting.

If the indicator needles do not return to “0”, adjust the
indicator so that the “0” moves 1/2 of the indicated differ-
ence from the needle to the “0” established during the
previous step.
CAUTION
If the needle is more than 0.10 mm [0.004 inch] from the
“0” established during the previous step, check for dirt
or burrs on the mandrels and fixture. If the “0” is still not
within the specification, check the be sure that the
master rod is not damaged.
CAUTION
Do not adjust the indicators during this step of the
procedure or the measurements will be wrong.
After completing the calibration of the fixture, remove the
mandrels from the master rod.
Measure the Connecting Rod Length

Repeat the same steps to install the mandrels in the rod to
be measured as you did for the master rod.
Install the rod in the fixture.
ProCarManuals.com
Record the indicator reading. The difference of the cali-

brated “0” of the indicators must be added or subtracted
from the known length of the master rod to determine the
length of the rod being measured.
Connecting Rod Length

mm in
289.69 MIN 11.405
289.74 MAX 11.407
If the connecting rod length is not within specifications, the
rod must be replaced or the piston pin bushing replaced
and machined.
Measure the Connecting Rod Bend (Bore Alignment)

CAUTION
Never attempt to straighten a connecting rod useing
heat or force. The rod will break eventually and cause
extensive engine damage.
Make a note of the indicator readings.
Remove the rod from the fixture. Turn the rod 180 degrees
ProCarManuals.com
horizontally.
Compare the indicator readings with those noted in the
previous step. The difference between the indicator read-
ing is the amount of bend in the connecting rod.
Connecting Rod Bend

mm in
0.01 MAX 0.004
MAX 0.008
If the connecting rod bend is not within specification with
the bushing installed, the bushing can be removed and the
bend measured again. If the connecting rod is not within
specifications with the bushing removed, the rod must be
replaced.
Measure the Connecting Rod Twist

Check the fixture and mandrel in the piston pin end for a
gap between the two. If there is any twist in the rod, the
mandrel will only touch one side of the fixture.
Hold the end of the mandrel that is touching the fixture
firmly against the fixture.
Use a feeler gauge to measure the gap between the man-
drel and the fixture. The amount of the gap between the
mandrel and the fixture is the amount of connecting rod
twist.
Maximum Connecting Rod Twist

mm in
Bushing Installed 0.25 MAX 0.010
Bushing Removed 0.51 MAX 0.020
If the connecting rod twist is not within specification with
the bushing installed, the bushing can be removed and
within specification with the bushing remove the must be
replace.

The connecting rod and cap must be assembled during
this check.
Use the residual method. Apply head shot amperage. Ad-
just the amperage to 1500 ampere D.C. or rectified A.C.
Check for cracks.
Use the residual method. Apply coil shot amperage. Check

for cracks.
Amperage
(Ampere Turns)
MIN 2600 D.C. or Rectified
A.C.
MAX 2800 D.C. or Rectified
A.C.
ProCarManuals.com

in the coil.
The connecting rod must be replaced if any indications are

visible in the critical (shaded) areas.
CAUTION
The rod must be demagnetized completely and cleaned
damage.
Demagnetize the connecting rod.
Use solvent or steam. Clean the part.
Crankshaft (001-016)
Clean
NOTE: New crankshafts are coated with a heavy preser-
vative. Use solvent to remove the coating thoroughly. Brush
or flush the packing debris from the oil drilling before in-
stalling the crankshaft in the engine.
Use a hone stone to remove all small scratches, grooves
and to polish the O.D. at the front and rear oil seal loca-
tions, the flywheel mounting location, and the vibration
damper location.
NOTE: Use a light preservative oil to prevent rust during
engine rebuild. Place tape over the threaded holes. If the
crankshaft is not going to be installed immediately, use a
heavy preservative oil.
WARNING
personal injury.
Use solvent to clean the crankshaft.
ProCarManuals.com

NOTE: Make sure to blow out the threaded holes on each
end of the crankshaft and the oil drillings. Use a light
preservative oil to prevent rust during engine rebuild. Tape
over the thread holes.
Use crocus cloth or a 400 grit emery cloth to remove dis-

coloration or light scratches from the machined surfaces.
CAUTION
Do NOT chase the threads in the crankshaft, severe
engine damage may occur.
The QSK19 uses rolled threads in the bolt holes in the nose
of the crankshaft.
To clean the ROLLED threads, flush with solvent.
Dry the threads with compressed air.
If additional cleaning is required, brush with a nylon bristle
brush.
Use a bristle brush and solvent to clean all of the oil drilling.
To prevent rust use, a light preservative oil to lubricate the
crankshaft.
Inspect for Reuse

Measure the O.D. at the locations shown.
Crankshaft O.D.
mm in
Location (1) 152.35 MIN 5.998
152.40 MAX 6.000
Location (2) 111.07 MIN 4.373
ProCarManuals.com
111.13 MAX 4.375

Location (3) 110.74 MIN 4.360
110.77 MAX 4.361
CAUTION
Do NOT chase threads on the crankshaft. Severe engine
damage may occur.
Check the threads for damage at both ends of the crank-
shaft.
If necessary refer to Bulletin No. 3379035, Alternative Re-
pair Manual, for repair instructions.
Check the main bearing journals and the rod bearing jour-
nals for damage or excessive wear. Minor scratches are
OK.
Measure the O.D.
Rod Bearing Journal O.D. (4)

mm in
101.524 MIN 3.997
101.600 MAX 4.000
Main Bearing Journal O.D. (5)

mm in
139.637 MIN 5.4975
139.700 MAX 5.5000
Measure the thrust distance between the thrust faces on
the No. 6 main bearing journal.
Thrust Distance (6)

mm in
60.30 MIN 2.374
60.33 MAX 2.375
NOTE: The crankshaft can be ground undersize if the O.D.
is not within specifications. Always grind all of the journals
when one is not within specifications.
Oversize rod bearings and main bearings are available.
Refer to the Alternative Repair Manual, Bulletin No.
ProCarManuals.com
3379035, for grinding specifications and instructions.
NOTE: Oversize thrust bearings are available if the thrust

distance is not within specifications. A 0.25 mm [0.010
inch] and a 0.51 mm [0.020 inch] oversize thrust bearing
are available. If the crankshaft must be machined to use an
oversize thrust bearing, refer to the Alternative Repair
Manual, Bulletin No. 3379035, for instructions.
Use a light preservative oil. Lubricate the crankshaft to
prevent rust. If the crankshaft is not going to be used
immediately, use a heavy preservative oil.

Perform the head shot and inspection method. Then per-
form the coil shot and inspection method.
Adjust the machine to 1800 ampere D.C. or rectified A.C.
Use the continuous method. Wet only 1/3 of the crankshaft
at a time.
Check the crankshaft for cracks.
Use the coil shot method. Use a coil that is a minimum of

514 mm [20 1/4-inch] in diameter.
Use the continuous method. Apply coil shot.
Amperage - (Ampere Turns)

MIN 4500 D.C. or
Rectified A.C.
MAX 5000 D.C. or
Rectified A.C.
NOTE: Ampere turn is an electrical current of one ampere flowing through the coil, multiplied by the number of turns
in the coil.
Check the crankshaft for cracks.
ProCarManuals.com
Limits of Acceptance - Open Indications

An open indication is visible to the eye after wetting op-
eration has been completed. An indication below the sur-
face is not visible to the eye after the wetting operation has
been completed. An indication below the surface can be
seen with the use of the ultraviolet light that is part of the
machine.
Do not use the crankshaft if:
• There is an indication in the fillet or in the shaded
area.
• There is an indication that passes through the 45
degree diagonal from the oil hole or goes into the oil
hole chamfer.
• There is an indication that is longer than 6 mm
[1/4-inch].
• There are more than four indications on one journal.
Limits of Acceptance - Indications Below the Surface

Do not use the crankshaft if:
• There is an indication in the fillet or in the shaded
area that is in a circumferential direction.
• There is an indication in a circumferential direction
that is longer than 25.4 mm [1.0 inch].
• There is an indication in an axial direction that is
longer than 9.5 mm [3/8-inch].
• There is an indication that is closer than 1.5 mm
[1/16-inch] to an oil hole chamfer.
• There is an indication that passes through the 45
degree diagonal from the oil hole.
CAUTION
The crankshaft must be demagnetized completely and
cleaned thoroughly. Small metal particles will cause
engine damage.
Demagnetize the crankshaft.
CAUTION
burns.
Use steam. Clean the crankshaft and the oil drillings. Refer
to the Procedure 001-016.
Use a light preservative oil. Lubricate the crankshaft to
prevent rust.
NOTE: Use a heavy preservative oil if the crankshaft is not
going to be installed immediately. Protect the part with a
cover to prevent dirt from sticking to the oil.
Bend and Twist Inspect

The crankshaft straightens is determined by the amount of
bow and the adjacent journal run out.
ProCarManuals.com
The following definitions will help you understand the pro-

cedure.
Definitions:
1. Bow:
One-half (1/2) of the TIR measured at the middle bearing
journal when the crankshaft is supported on the two end
journals. Bow is often referred to as the bend or the full
length alignment.
2. Journal Run Out:

The TIR (total sweep of the needle) of the main bearing
journal as the crankshaft is rotated one complete revolution
(360 degrees).
3. Adjacent Journal Run Out:

The relationship of the TIR of a main bearing journal as it
is rotated on a common axis to the TIR of an adjacent
journal.
Adjacent Journal Run Out is often referred to as the step
run out, the bearing-to-bearing run out, or the journal-to-
journal run out.
4. Clock Position:
The location of the journal at the highest TIR point. Com-
pare its angular relationship with the No. 1 crankshaft pin
as viewed from the front of the crankshaft. In this example,
the crankshaft pin is at the 8 o’clock position. This is the
clock position of the journal being measured.
ProCarManuals.com
Use two vee blocks. Put the vee blocks on a flat surface.
Support the crankshaft on the vee blocks at the two end
bearing journals.
Use a dial indicator. Position the indicator so the stem

touches the bearing journal being measured at the journal
centerline.
The point of measurement chosen must be used for mea-
suring all bearing journals.
Rotate the crankshaft and measure the TIR at each bearing

journal. Record the value and the clock position for each
journal.
Determine the Crankshaft Bow

Crankshaft bow as specified, is the TIR of the center journal
when the crankshaft is rotated thru 360 degrees, while
supported on the end of the journals.
Compare the bow to the specifications.
Maximum Crankshaft Bow (TIR)
mm in
ProCarManuals.com
0.23 FFH 0.009

NOTE: All QSK19 crankshafts are Fully Fillet Hardened.
Determine the Adjacent Journal Run Out

For each journal, plot the TIR value at its clock position on
a polar chart illustrated on the following page.
The end journals supported by vee blocks must be plotted
at the center of the chart.
The example illustrates the following plot points.
Journal TIR Clock Position

1 0 0
2 0.0021 12
3 0.0030 12
4 0.0039 1
Draw a straight line between the plotted points, (from jour-

nal No. 1 to No. 2, and from No. 2 to No. 3), until all journals
are plotted on the chart.
To determine the Adjacent Journal Run Out, measure the
length of the line from each journal to its corresponding
journal point.
Illustrated as an example, journal No. 3 and No. 4 is 5.1 mm
[2 inch]. This represents a run out of 5.1 mm [0.002 inch].
Record the adjacent journal run out for each bearing jour-
nal. Compare the adjacent journal run out to specifications.
Maximum Adjacent Journal Run Out

mm QSK19 in
0.089 FFH 0.0035
Replace the crankshaft if any measurement is not within
specifications.
ProCarManuals.com
ProCarManuals.com
Crankshaft Gear, Front (Crankshaft Installed) (001-018)
Crankshaft Gear, Front (Crankshaft

Installed) (001-018)
Remove
Remove the gear cover and all related components. Refer
to the QSK19 Troubleshooting and Repair Manual, Bulletin
No. 3666098-01.
Remove the cover spacer plate. Refer to the QSK19 Trouble-
shooting and Repair Manual, Bulletin No. 3666098-01.
NOTE: ONLY remove the gear when the crankshaft or the

gear is damaged.
Use a puller jaw, Part No. 3375835, and bridge assembly,
Part No. 3375834. Install the puller jaw and bridge assem-
bly on the gear.
ProCarManuals.com
CAUTION
Heat can be used to aid the removal of the gear. Do NOT
use a cutting torch. The high temperature of a torch will
damage the teeth of the gear.
CAUTION
Do not exceed 475 N•m [350 ft-lb] of torque when turn-
ing the jackscrew.
Lubricate the puller jackscrew with engine oil. Hold the pry
bar and turn the jackscrew to remove the gear.
Remove the key.

Use a hone stone and polish the shaft O.D. Remove all of
the small scratches, burrs, and small grooves.
Inspect for Reuse

Clean and visually inspect the crankshaft for reuse. Mea-
sure the O.D.
Crankshaft O.D. (Gear Location)

mm in
111.25 MIN 4.380
111.28 MAX 4.381
Install
Install the key.
ProCarManuals.com
CAUTION
burns.
CAUTION
CAUTION
Use an oven and adjust the heat to 235°C [450°F]. Heat
the gear for a minimum of 1 hour, but no more than a
maximum of 6 hours. The I.D. of the gear will become
larger and will simplify installation.
Crankshaft Gear, Rear (Crankshaft Installed) (001-020)
CAUTION
burns.
CAUTION
Allow the gear to air cool slowly. Do not use water or oil
to reduce the cooling time. This will cause the gear to
crack.
NOTE: The timing mark on the crankshaft gear must be
visible from the front of the gear after it is installed on the
crankshaft.
Lubricate the O.D. of the crankshaft with LubriplateT No.
105, or equivalent. Remove the gear from the oven and
install it on the crankshaft. The keyway in the gear must be
aligned with the key in the crankshaft.
Install the gear cover and related components. Refer to

Procedure No. 001-031.
ProCarManuals.com
Crankshaft Gear, Rear (Crankshaft

Installed) (001-020)
Install
Crankshaft Pulley (001-022)
Clean
WARNING
personal injury.
Use solvent or steam. Clean the pulley.
Inspect for Reuse

Check all mounting pilots and surfaces for damage from
fretting. If it is not possible to remove the damage with a
240 grit abrasive cloth, the part must be replaced.
CAUTION
The mounting pilots and surfaces control the center
and spacing of the pulleys. Do not repair the part by
machining. It will cause an out-of-balance condition or
a crankshaft failure.
Measure the O.D.
Pully O.D.
mm in
134.78 MIN 5.3105
135.04 MAX 5.3115
Measure the I.D.
Pully I.D.
mm in
ProCarManuals.com
110.780 MIN 4.3610

110.806 MAX 4.3620
Vibration damper to pulley torque:

Cylinder Block (001-026)

Worksheet
Cylinder Block Inspection Checklist
1. Cylinder Liner Counterbore
a.Upper Bore I.D.
b. Lower Bore I.D.
c. Depth
d. Ledge Flatness
e. Ledge Cracking
2. Packing Ring Bore I.D.
3. Idler Shaft Bore I.D.
4. Head Deck - Damage
5. Water Hole - Damage
6. Idler Shaft Bore I.D.
7. Camshaft Bushing Bore I.D.
8. Main Bearing Bore
a. Alignment
b. I.D.
9. Main Bearing Cup Fit in Block
10. Cylinder Head Capscrew Threads
ProCarManuals.com
Clean
Use a drill, a sheet metal screw, and the following parts
from a light duty puller kit, Part No. 3375784:
• Slide hammer
• Hook
Remove the following cup plugs:

1. Main oil passage cup plug
2. Piston cooling oil passage cup plug
3. Main oil passage cup plug
4. Piston cooling oil passage cup plug
ProCarManuals.com
Remove the following straight thread pipe plugs:

5. Main oil passage straight thread pipe plug
6. Water pump idler oil passage straight thread pipe plug
7. Piston cooling oil passage
Remove the seven cup plugs from the camshaft oil

passages.
Remove the cup plug from the hydraulic pump idler oil
passage.
Remove the straight thread pipe plug from the lubricating
pump oil passage.
Use a dowel pin extractor, Part No. ST-1134, or equivalent.

Remove the 12 cylinder head groove pins.
• Put the split collet (8) over the groove pin.
• Slide the extractor collar (9) over the split collet.
• Use the slide hammer (10) to push the extractor
collar over the split collet tightly.
• Use the slide hammer to remove the groove pin.
ProCarManuals.com
CAUTION
Do not damage the machined gasket surfaces or the
camshaft bushings.
Use a scraper, a wire brush, or a 120-grit emery cloth.
Clean all of the heavy dirt deposits off of the cylinder block.
Clean:
• all of the gasket surfaces,
• all of the mounting surfaces,
• the cylinder liner counterbore ledge and the press
fit areas,
• the cylinder liner packing ring bore,
• the top of the block,
• the main bearing saddles and the caps,
• all of the cup plug bores.
Use a bottle brush with a long handle. Clean all the oil
passages.
WARNING
Use gloves, an apron, and goggles to prevent personal
injury.
CAUTION
Use a cleaning solution that will not damage the cam-
shaft bushings.
Remove the block from the engine stand.
Follow the instructions of the manufacturer of the cleaning
tank and the manufacturer of the cleaning solution.
NOTE: Cummins Engine Co., Inc. does not recommend
any specific cleaning solution.
Past experience shows that the best results are obtained
using a cleaning solution that can be heated from 80°C to
95°C (180°F to 200°F).
A cleaning tank that will mix and filter the cleaning solution
will give the best results.
WARNING
Use gloves, an apron, and goggles to prevent personal
ProCarManuals.com
injury.
Remove the block from the cleaning tank.
Use a steam cleaner. Be sure all of the oil passages are
clean.
CAUTION
Be sure all of the water is removed from the capscrew
holes and the oil passages.
Use compressed air. Dry the block.
NOTE: If the cylinder block is not going to be used imme-
diately, apply a coating of preservative oil to prevent rust.
Cover the block to prevent dirt from sticking to the oil.
Inspect for Reuse

Cylinder Block Surface Condition
CAUTION
All measurements of the cylinder block must be made
when the block is positioned on a flat surface. If the
block is mounted on an engine stand, distortion will
cause the measurements to be wrong.
Definition of numerical terms:
1. Upper Counterbore Inside Diameter
2. Counterbore Depth
3. Lower Counterbore Inside Diameter
4. Packing Ring Bore
5. Counterbore Ledge
6. Counterbore Radius
CAUTION
Do not install any cup plugs or pipe plugs in the block
until the inspection and any necessary repair proce-
dures are completed. This will prevent dirt from being
trapped in the oil passages.
Use pipe Loctite sealant, Part No. 3375068, or equivalent,
and the correct size cup plug driver.
Use a cup plug driver handle, part No. 3376795 with all cup
plug drivers.
Check the top surface of the block for wear. If fretting

damage is present in an area where a head gasket seal ring
or a grommet makes contact, the surface must be repaired.
Fretting damage in any other area is acceptable if it does
not change the protrusion measurement of the counter-
bore or liner.
A newly machined surface must be flat within 0.05 mm
[0.002 inch] under a cylinder head. Waves on the surface
ProCarManuals.com
are acceptable as long as they are not more than 0.018 mm

[0.0007 inch] high, and the high and low points of the
waves are not closer than 25 mm [1.0 inch].
A newly machined surface must meet the specifications for
block height as stated in the next illustration. If the top
surface of the cylinder liner counterbore must be machined.
Refer to procedure No. 001–058.
CAUTION
The parting line of the main bearing cap is not at the
same height as the centerline of the main bearing bore.
(13) Cylinder Block Height

mm in
481.91 MIN 18.9735
482.76 MAX 19.0065
If the height of the block is less than 482.42 mm [18.993
inch], a 0.51 mm [0.020 inch] oversize head gasket must
be used.
If the checking ring or the centering ring is not available,
the height of the block can be measured from the top of the
main bearing saddle (14)
(14) Cylinder Block Height- Main bearing Saddle

mm in
407.70 MIN 16.051
408.53 MAX 16.084
If the block height is less than 408.20 mm [16.071 inch] a

0.51 mm [0.020 inch] oversize head gasket must be used.
The height of the block must not vary more than 0.05 mm
[0.002 inch] from end to end of the block. If the block height
is not within specifications, the top surface of the block
must be machined or the block must be replaced.
NOTE: If the top surface of the block is machined, the ledge
depth of the cylinder liner Canterbury must be machined.
Refer to procedure number 001-058.
Measure the Main Bearing Bore Alignment

Use two centering rings, Part No. ST-1177-54 [5.846 inch
diameter]. Put the rings in the No. 2 and the No. 6 main
bearing locations.
ProCarManuals.com
CAUTION
The main bearing caps are numbered through 7. Install
each cap in the correct location. The slot in the cap for
the bearing tang must be on the same side as the slot
in the block.
Install each capscrew by hand to be sure the capscrew is
positioned properly.
Use a mallet. Install the caps until they touch the block.
If any of the caps do not require force during installation,
mark the cap to check the side clearance.
Tighten the main bearing caps using two steps.
Torque Value:
Step 1 270 N•m [200 ft-lb]
Step 2 610 N•m [450 ft-lb]
Use engine oil. Lubricate the I.D. of the two centering rings.
Install the alignment/boring bar, Part No. ST-1177-16, in the
two centering rings. The bar must turn easily. If the bar
does not turn easily, check to be sure that the main bearing
caps are installed correctly. If they appear to be OK, move
one of the centering rings to another bearing location.
Use your hands to install the checking ring in the main

bearing bore. If the ring will not slide through the bore,
check the bore for burrs. If the ring will still not slide through
the bore, the bore is undersized and must be repaired.
Refer to Bulletin No. 337035, Alternative Repair Manual,
for repair procedures.
Use a 0.075 mm [0.003 inch] feeler gauge that is not more

than 13 mm [0.5 inch] wide.
Center the checking ring in the bore. Try to put the feeler
gauge between the checking ring and the bore. Rotate the
gauge in the bore at both sides of the checking ring.
the bore alignment of the main bearing is OK if:
• The gauge does not enter at any point.
• The gauge will enter, but will not slide through or
ProCarManuals.com
around the bore, and the alignment bar will rotate

with the gauge inserted.
The bore alignment of the main bearing is not OK if:
• The gauge enters and slides around the bore. this
means that the bore is oversize and must be re-
paired.
• The gauge will enter on one side only, but can slide
around the bore. This means that the bore is tapered
and must be repaired.
If the tools to check the main bearing bore alignment are

not available, use a dial bore indicator.
Measure the I.D. in the three positions shown. The I.D.
must be completely round within 0.013 mm [0.0005 inch].
NOTE: Support the rear portion of the block on a flat sur-
face to obtain the most accurate measurement of the I.D.
Check the main bearing caps that are loose. The main
bearing cap must be replaced if :
• The clearance causes the main bore alignment not
to be within specifications.
• The clearance between the block and the cap is
more than 0.17 mm [0.007 inch] on either side of the
cap when the cap is installed and torqued to speci-
fications.
• There is fretting or heat damage to the cap.
NOTE: On new or reconditioned blocks, the main bearing
cap is 0.00 mm to 0.013 mm [0.00 inch to 0.010 inch] larger
than the block. Force must be used to install the cap.
Service caps do not have the bore machined to a final
specification. If the cap is machined. Use the correct parts
of the main bearing boring tool, Part No. ST-1177. Refer to
Bulletin No. 3379035, Alternative Repair Manual.
Check the water holes (15). If erosion or pitting is more than

0.08 mm [0.003 inch] deep, or extends more than 2.41 mm
[0.095 inch] from the edge of the hole, the water hole must
be repaired. Refer to Bulletin No. 3379035, Alternative
Repair Manual.
Check the threads of the bolt holes (16) for damage. Use
ProCarManuals.com
a threaded insert if a damaged bolt hole must be repaired.

Refer to bulletin No. 3379035, Alternative Repair Manual.

Use a crack detection kit, Part No. 337532, or equivalent,
and check the counterbore ledge for cracks.
Circumferential cracks of the counterbore ledge are ac-
ceptable if they do not extend to or over the edge of the
ledge (LPF I.D.). Circumferential cracks in the radius are
acceptable if they do not extend more than 90 degrees
around the radius.
It is not necessary to machine the block in an effort to

remove ACCEPTABLE cracks. If cracks that are not ac-
ceptable are found during the initial inspection, the count-
erbore ledge must be machined. Refer to Procedure No.
001-058. If a crack that is not acceptable remains after the
machining repair procedure is completed, the block is not
acceptable for reuse.
Capscrew Hole Cracks

Cracks that extend from the counterbore wall to the
capscrew hole are acceptable for reuse only if it does not
extend into the threaded portion of the hole.
Cracks that extend into threaded portion of the hole require

repair with a blind end thread insert. Refer to the Alterna-
tive Repair Manual, Bulletin No. 3379035.
ProCarManuals.com
Coolant Passage Cracks

If a crack is running horizontally around the counterbore,
all the coolant passages that are close to the bore must be
repaired with coolant passage threaded inserts.
Some cracks will run vertically to a coolant passage or a

capscrew hole. Those passages must be repaired with
coolant passage threaded inserts.
Use the Coolant Passage Repair Kit, Part No. 3824047, to
repair the coolant passages.
NOTE: If the crack extends over the counterbore ledge the
block can not be repaired.
Cylinder Block and Liner Seats (001-027)
Cylinder blocks with vertical cracks that extend from a

coolant passage down over the counterbore ledge can not
be repaired.
Cylinder Block and Liner Seats

(001-027)
General Information
Definition of numerical terms (call-outs):
1. Upper counterbore inside diameter
2. Counterbore depth
ProCarManuals.com
3. Lower counterbore inside diameter

4. Packing ring bore
5. Counterbore ledge
6. Counterbore radius
Rail Applications
To allow for the proper coolant drainage of the cylinder
head and engine block on a horizontally mounted QSK19
Rail engine, a coolant drain drilling was added to the cyl-
inder block. The drilling runs the entire length of the cyl-
inder block and passes through the center of each cylinder
liner cavity. The drilling is plugged by a 1/4” pipe plug.
NOTE: Do not remove the plug.
Inspect for Reuse

Measure the liner protrusion. .
NOTE: If the protrusion is not correct, remove the liner.
Refer to Procedure 001-064. The protrusion can be ad-
justed using seal rings, and machining the counterbore
ledge.
Inspect the cylinder block to determine if an oversize or a

standard size head gasket is required.
NOTE: An oversize head gasket may be required on blocks
that have had material removed from the top surface of the
block. Check the block for markings indicating an over-
sized gasket is required.
Use a scraper or a fibrous abrasive pad such as Scotch-

Brite 7477, or equivalent, and solvent. Clean the top deck
surface of the block. Do not allow any dirt into the cylinder.
The surface must be free of dirt, oil, and gasket material,
but does not have to look like new metal.
NOTE: Check the top surface of the block for wear. If
fretting damage is present in an area where a head gasket
seal ring or a grommet makes contact, the surface must be
repaired. Refer to the Alternative Repair Manual, Bulletin
ProCarManuals.com
No. 3379035.
NOTE: Fretting damage in any other area is acceptable
only if it does not change the protrusion measurement of
the counterbore or liner.
Visually inspect the groove pins for damage. Use the ST-
1134 dowel pin extractor, or equivalent, to remove the pins.
Measure
NOTE: Be sure the micrometer contacts the flat surface of
the ledge. It must not touch the radius.
NOTE: If the counterbore depth does not meet specifica-
tions, a thicker or thinner seal ring may have been used
in a previous machining bore process. Measure and record
the measurement so that the liner protrusion can be de-
termined.
Use a depth micrometer and measure the counterbore
depth at the four places shown.
Counterbore Depth
mm in
13.755 MIN 0.5415
13.805 MAX 0.5435
The four measurements must not vary more than 0.25 mm
[0.001 inch]. If the measurements exceed the specifica-
tions, the counterbore ledge must be machined.
NOTE: Be sure that the indicator does not contact the

counterbore radius on a block that does not have a double
undercut.
ProCarManuals.com
Use depth gauge assembly, Part No. 3823495. Measure

the angle of the counterbore ledge at four places on the
counterbore circumference.
The measurement of the ledge depth must be as near to
the counterbore radius as possible, and as near to the
counterbore edge as possible.
The angle (12) of the counterbore ledge is acceptable (OK)

if the measurement that is near the counterbore edge is the
same or no more than 0.036 mm [0.0014 inch] shorter than
the measurement near the counterbore radius. If the mea-
surement near the counterbore ledge is longer than the
measurement near the counterbore radius, the ledge must
be machined.
Measure the I.D. of the upper counterbore (1). The point of

measurement must be within 2.54 mm [0.100 inch] from
the top of the block.
Counterbore Diameter - UPPER Press Fit Diameter

mm in
188.16 MIN 7.409
188.21 MAX 7.410
The I.D. of the upper counterbore must be completely
round within 0.050 mm [0.002 inch]. If the measurement is
not within specification, check to see if the block can be
machined to use oversize liners.
NOTE: The upper counterbore must be no more than
0.076 mm [0.003 inch] larger than the cylinder liner flange.
NOTE: If the counterbore does not meet specifications, an
oversize liner may have been used in a previous machining
bore process. Measure and record the measurement so
that the proper press fit liner can be determined.
Measure the I.D. of the lower counterbore (3). The point of

measurement must be within 2.54 mm [0.100 inch] from
the top of the counterbore ledge.
ProCarManuals.com
Counterbore Diameter - LOWER Press Fit Diameter

mm in
180.09 MIN 7.090
180.14 MAX 7.092
The I.D. of the lower counterbore must be completely round
within 0.050 mm [0.002 inch].
NOTE: If the counterbore does not meet specifications, an
oversize liner may have been used in a previous machining
bore process. Measure and record the measurement so
that the proper press fit liner protrusion can be determined.
If the block is not within specifications, do not use the
block.
Check the chamfer at the top of the packing ring bore.

Excessive pitting must be repaired. Refer to the Alternative
Repair Manual, Bulletin No. 3379035.
(4) Packing Ring Bore

mm in
177.34 MIN 6.982
177.40 MAX 6.984
Cylinder Liner (001-028)
Leak Test
Clean
CAUTION
Do not use a hone, deglazing, or prebrushing to clean
the cylinder liners. Abrasives can damage the finish and
the crosshatch pattern and can contaminate the liner.
WARNING
Wear eye protection. Make sure the wire brush is rated
for the RPM being used if the brush is motor driven.
Use a high quality steel wire brush to clean the liner flange
seating area.
Use a non-metallic bristle brush, detergent soap, and warm

water to clean the inside diameter.
Use a steam cleaner or solvent tank to lean the liners.
ProCarManuals.com
Use clean engine oil. Lubricate the I.D.

Allow the liner to soak for five to ten minutes
CAUTION
Do not use a cloth towel. Lint will cause severe engine
damage.
Use a paper towels. Wipe the liner I.D.
Repeat these three cleaning steps until the paper towel
shows no gray or black residue.
Inspect for Reuse

Visually inspect the liners for cracks on the inside and the
outside diameters.
Inspect for cracks under the flange.

NOTE: Cracks can also be detected by using either mag-
netic inspection or the dye method.
ProCarManuals.com
Visually inspect the outside diameter for excessive corro-

sion or pitting. Pits must not be more than 1.6 mm [0.063
in] deep.
Replace the liner if the pits are too deep or if the corrosion
can not be removed with a fine emery cloth.
Inspect the inside diameters for vertical scratches deep

enough to be felt with a fingernail.
NOTE: If a fingernail catches in the scratch, the liner must
be replaced.
Visually inspect the inside diameter for scuffing or scoring.
Visually inspect the inside diameter for liner bore polishing.

A moderate polish produces a bright mirror finish in the
worn area with traces of the original hone marks or an
indication of an etch pattern.
A heavy polish produces a bright mirror finish in the worn
area with no traces of hone marks or an etch pattern.
NOTE: Refer to Parts Reuse Guidelines, Bulletin No.
3810303, for further information on liner bore polishing.
Replace the liner if:

• A heavy polish is present over twenty percent (20%)
of the piston ring travel area.
• Thirty percent (30%) of the piston ring travel area
has both moderate and heavy polish, and one-half
(15 percent) is heavy polish.
ProCarManuals.com
Use a dial bore gauge. Measure the I.D. of the liner at the
top, the bottom, and the middle of the piston ring travel
area. Perform two measurements at each location. The
measurements must be 90 degrees apart.
Cylinder Liner I.D.

mm in
158.737 MIN 6.2495
158.877 MAX 6.2550
NOTE: The I.D. of a new cylinder liner can be 0.015 mm
[0.0006 inch] smaller than specifications because of the
LubriteT coating.
Measure the liner flange outside diameter.
Upper Press Fit Liner Flange Diameter

mm in
188.24 MAX 7.411
Oversize 20/20 188.70 MIN 7.429
188.75 MAX 7.431
NOTE: The liner design incorporates a press fit between

the upper liner bore and the area of the liner directly below
the liner flange. This is referred to as the Lower Press Fit
(LPF) design.
NOTE: Cylinder liners with standard and oversize press fit
diameters are available.
Measure the lower press fit diameter.
Lower Press Fit Area O.D.

mm in
180.21 MAX 7.095
Oversize 20/20 180.67 MIN 7.113
180.72 MAX 7.115
ProCarManuals.com
Measure the liner flange thickness.
Liner Flange Thickness

mm in
13.398 MIN 0.5275
13.424 MAX 0.5285
Apply a thick film of clean 15W-40 oil to the bores of the

liners for final cleaning. Leave the oil on for 5 to 10 minutes.
Use a clean, lint-free paper towel, not cloth, to wipe the oil
from the bores until the black and gray deposits are re-
moved.
NOTE: Do not set the liners in an area where dirty air flow
can contaminate the liners.
Gear Cover Spacer Plate (001-029)

Clean
Use solvent, clean the Gear Cover Spacer Plate.
Inspect for Reuse

Inspect the plate for reuse. Check for fretting damage on
both sides of the gasket surface. Replace the plate if dam-
aged.
Check the mounting stud threads for damage.
Install new studs to the specified height.
Accessory Drive Stud (1)- Installed Height

ProCarManuals.com
mm in
31.88 MIN 1.255
33.15 MAX 1.305
Water Pump Drive Stud (2) — Installed Height

Gear Spacer Plate and Gear Housing
mm in
62.99 MIN 2.480
63.75 MAX 2.510
Gear Cover, Front (001-031)

Clean
WARNING
When using solvents, acids or alkaline materials or
steam for cleaning, follow the manufacture’s recom-
mendations for use. Wearing goggles and protective
clothing to avoid personal injury.
Use solvent or steam. Clean the front cover and related
parts.
Inspect for Reuse

Measure the I.D. of the bushings. The bushings must be
replaced if not within specifications.
Accessory Drive & Water Pump Drive Bushing I.D.

mm in
39.75 MIN 1.565
39.90 MAX 1.571
Hydraulic Pump Drive (2) Bushing I.D.

mm in
38.13 MIN 1.501
38.25 MAX 1.506
Remove and check the barring mechanism.

Push the shaft in. Hold in position. Slide the worm gear until
the spring is compressed.
Use a screwdriver. Remove the retaining ring.
ProCarManuals.com
Remove the parts:

• Shaft
• Spring
• Worm gear
Remove the o-ring from the shaft. Discard the o-ring.
Use solvent to clean the parts. Flush the oil drillings. Dry
with compressed air.
NOTE: Some contact marks on gear are acceptable.
Check the parts for severe damage.
Use vegetable oil to lubricate the o-ring. Install the o-ring

on the barring shaft.
Install the parts:
• Worm gear
• Spring
• Shaft
Idler Gear, Camshaft (001-036)
Install the retaining ring.

Rotate the shaft. Check for correct assembly.
Measure
Barring Mechanism Bushing Bore
Measure the I.D. of the bushing bore.
Barring Mechanism Bushing Bore

mm in
18.215 MIN 0.717
18.265 MAX 0.719
ProCarManuals.com
The bushing must be replaced if not within specifications.

Clean
Use solvent. Clean the idler gear and parts.
Inspect for Reuse

Check the parts for damage.
Measure the I.D. of the idler.
Idler Gear Bushing I.D.

mm in
47.638 MIN 1.8755
47.714 MAX 1.8785
NOTE: The bushing in the gear is precision bored after
installation. If machining capability is not available, replace
the bushing and the gear as an assembly.

CAUTION
Use a copper braid contact that has neoprene covers to
avoid burning the teeth of the gear.
CAUTION
the keyway points toward one of the contacts when
checking.
Use the residual method. Apply head shot amperage.
Adjust the amperage to the specified value
Gear O.D. Amperage D
Greater than 203mm [8 inch] 2000
CAUTION
ProCarManuals.com
the keyway points toward the coil.

Adjust the amperage to the specified value
Gear 0.D. Ampere Turns
Less than 101 mm [4 4000
inch]
101 mm to 203 mm [4 6000
inch to 8 inch]
Greater than 203 mm [8 8000
inch]
in the coil.
Idler Gear, Hydraulic Pump (001-039)
Limits of Acceptance — on Machined Surfaces

An open indication is visible to the eye after the wetting
operation has been completed. An indication below the
surface is not visible to the eye after the wetting operation
has been completed. An indication below the surface can
be seen with the use of the ultraviolet light that is part of the
machine.
• There is an open indication.
shaded area as shown.
• There is an indication below the surface that is longer
than 6 mm [1/4 inch].
Limits of Acceptance — on Forged Surfaces
• There is an open indication that is in a circumfer-
ential direction.
• There is an open indication that is longer than 9.5
mm [3/8 inch].
shaded area.
An indication below the surface in a radial direction is
ProCarManuals.com
acceptable (OK) if it is in the area that is not shaded.

CAUTION
The gear must be demagnetized completely and cleaned
damage.
Demagnetize the gear.
Use solvent or steam. Clean the part.
Idler Gear, Hydraulic Pump (001-039)

Clean
Use solvent. Clean the idler gear.
Idler Gear, Water Pump (001-040)
Inspect for Reuse

Check the gear and parts for any damage.
Idler Gear, Water Pump (001-040)

Clean
Use solvent clean the part.
Dry with compressed air
ProCarManuals.com
Inspect for Reuse

Check all parts for damage.
Piston (001-043)
Clean
WARNING
When using a steam cleaner, wear protective clothing
and safety glasses or a face shield. Hot steam can
cause serious personal injury.
Use steam to clean the outer layers of carbon from the
piston surface. The bead blast method can be used to clean
the top of the piston. If this method is used, cover the ring
grooves and skirt securely.
NOTE: It is only necessary to remove the carbon buildup.
It is not necessary to make the crown appear new.
Piston (001-043)
CAUTION
Do not contaminate the wash tank solution with bead
blast materials.
Use a kerosene emulsion-based solvent. Do not use a
solvent that is higher than 9.5 pH. Do not use a solvent
that contains chlorinated hydrocarbons with cresol,
phenols, or cresylic components.
Allow the pistons to soak in the solvent a minimum of 30
minutes.
NOTE: For best results soak the pistons several hours or
overnight. Use a solvent that can be heated from 90°C to
95°C [194°F to 203°F]. Use a cleaning tank that will cir-
culate and filter the solvent.
CAUTION
Do not use the bead blast method to clean the skirt. The
piston skirt will be damaged by blast material being
embedded in the aluminum.
CAUTION
Do not use a metal bristle brush to clean the pistons.
ProCarManuals.com
Damage to the ring grooves will result.

Use a brush to clean the ring grooves. Walnut shell blasting
can be used on the piston crown.
Repeat the soaking and scrubbing process until the piston
is thoroughly clean.
Use steam to rinse the solvent from the pistons. Dry the
pistons with compressed air.
Inspect for Reuse

Visually inspect both the crown and skirt. Do not use the
crown or skirt if cracks or scuff marks are found. Scratches
in the skirt are not acceptable if they are visually not
acceptable. Use crack detection kit, Part No. 3375432, or
its equivalent, to check for cracks on the piston crown and
in and around the piston pin bore. Do not use if cracked or
scuffed. If the crown is not acceptable, replace the crown
and pin.
Piston (001-043)
Visually inspect the ring grooves. The pistons must be

replaced if there is a visible ridge in the back of the groove.
The piston must be replaced if a lip has formed on the O.D.
of the groove.
Use piston ring groove wear gauge, Part No. 3824846, and
a 6 to 7 inch micrometer to inspect the top groove (com-
pression ring).
NOTE: The piston must be replaced if measured dimen-
sions are less than those in the table below.
Measure the top and second ring grooves (diameter over
pins) when the piston temperature is at 21°C (70°F) in two
places 90 degrees apart as shown.
ProCarManuals.com
Ring Groove Wear Limits (Diameter Over Pins)

mm in
Top Ring 159.100 MIN 6.2638
Second Ring 159.413 MIN 6.2761
Measure the oil ring groove. The piston must be replaced

if it is not within specification.
Piston Oil Ring Groove Width

mm in
4.788 MIN 0.1885
4.851 MAX 0.1910
Measure the piston pin bore inside diameter.
Articulated Piston Pin Bore I.D. (Crown)

mm in
60.960 MIN 2.4000
61.059 MAX 2.4039
Articulated Piston Pin Bore I.D. (Skirt)

mm in
60.949 MIN 2.3996
60.961 MAX 2.4000
Vibration Damper (001-052)
Measure the piston pin outside diameter and length.
Piston Pin O.D.

mm in
60.929 MIN 2.3988
60.935 MAX 2.3990
Piston Pin Length

mm in
132.59 MIN 5.220
132.85 MAX 5.230

Clean
Vibration dampers have a limited service life. The damper
must be replaced after 15,000 hours in service.
Do not repair or balance a viscous damper in the field.
WARNING
ProCarManuals.com

cleaning, follow the manufacture’s recommendation for
use. Wear goggles and protective clothing to avoid per-
sonal injury.
Use solvent. Clean the exterior of the damper.
Inspect for Reuse

NOTE: Vibration dampers have a limited service life. The
damper must be replaced after 576,000 km, [360,000
miles], or 15,000 hours of service.
NOTE: Do not repair or balance a viscous damper in the
field.
Inspect the damper for reuse. Inspect for cracks on the
mounting flange. Inspect for dents or bulges on the hous-
ing.
If the damper is damaged, it must be replaced.
Use a paint solvent and fine crocus cloth. Remove the paint
from the front and back of the housing at the four areas
shown.
Measure no less than 3 mm [1/8 inch] from the O.D. to be
sure that the measurement is on a flat surface.
Measure the thickness at four places. If the measurements
vary more than 0.25 mm [0.010 inch], or if the thickness
exceeds 42.24 mm [1.663 inch], the damper must be
replaced.
NOTE: The following illustrates the procedure to check the

damper for fluid leakage.
Use the crack detection kit, Part No. 3375434, or equiva-
lent, and spray the rolled lip of the damper.
NOTE: The crack detection kit, Part No. 3375434, contains
the necessary cleaner, penetrant, and developer to check
for cracks using the dye penetrant method.
CAUTION
burns.
Use an oven with the temperature adjusted to 93°C [200°F].
Put the damper in the oven with the rolled lip down. Heat
the damper for two hours.
ProCarManuals.com
CAUTION
burns.
Remove the damper and check for leakage around the lip.
If there is any leakage the damper must be replaced.
Cylinder Block Counterbore (001-058)

Machine
WARNING
Read the complete Procedure before beginning to ma-
chine the block.
The counterbore ledge will be machined. Sealing rings will
be used to obtain the correct cylinder liner protrusion.
The cylinder protrusion (A) is the total sum of the thickness
of the liner flange and the sealing rings, minus the count-
erbore depth.

mm in
0.13 MIN 0.003
0.18 MAX 0.007
NOTE: Some liners are oversize in flange thickness and
flange O.D.
If necessary, machine the block for oversize liners before

machining the counterbore ledge for depth. Refer to pro-
cedure No.
ProCarManuals.com
Resurface the block as required before machining the

counterbore ledge depth. Refer to Bulletin No. 3379035,
Alternative Repair Manual, for machining instructions.
Tools required
1. Drive unit, Part No. 3376685
2. Adapter plate, Part No. 3376684
3. Cutter plate, Part No. 3375980
4. Tool bit
5. Hex wrench [3/16-inch]
6. Hex wrench [3/32-inch]
7. Bolt spacers [3/16-inch I.D. by 3 1/2-inch]
8. Plain washers [3/16 I.D. by 2 inch O.D.]
9. Cylinder head capscrews for the block being machined
NOTE: The cylinder block counterbore tool, Part No.
3376684, contains the tools listed above. The same kit
contains the tools to machine the counterbore depth on all
Cummins engines except the L10.
Install the drive unit (1) on the adapter plate (2).

Align the key slot on the cutter plate (3) with the key on the
drive unit shaft. Install the plain washer and capscrew (10).
Use a mallet. Tap the cutter plate. the cutter plate must be
seated on the shaft.
NOTE: Radius specifications are in inches.
CAUTION
Part No. 3377468 must be used to machine the count-
erbore ledge.
Install the tool bit in the cutter plate. Position the bit so it
will cut when the plate is moving clockwise.
Push the tool bit into the plate until it is even with or below
the O.D. of the plate.
Some resistance can be felt when installing the bit exten-
sion device. If the bit will not go in, loosen the two locking
screws (16).
Use a fine, India type stone. Remove any nicks and burrs
from the head surface and counterbore ledge. Nicks and
burrs will prevent the tool from seating correctly.
Use a depth micrometer to measure the counterbore depth.
Measure at four equally spaced points. Record the
measurements.
ProCarManuals.com
CAUTION
Do not use more than three seal rings under one liner.
The use of one thick seal ring is better than two thin
shims.
Measure the thickness of the sealing rings used with the
engine block being machined.
Select the best combination of sealing rings and counter-
bore ring to achieve the correct protrusion.
CAUTION
Do not allow the weight of the cutter plate to cause it
to fall. The bit plate will be damaged. Hold up on the
shaft when pulling the licking pin.
Set the cylinder block counterbore tool on the block.
Pull the locking pin. Lower the cutter plate until it touches
the counterbore ledge. The taper on the cutter plate will
center the tool in the cylinder bore.
There must be clearance between the stop collar (19) and
the housing. Turn the collar until there is clearance.
Turn the shaft backward and forward. The taper must be
positioned squarely in the bore.
There must be no clearance between the adapter plate

mounting surface and the block head surface.
Align the holes in the adapter plate (2) with two cylinder
head capscrew holes in the block. Install the plain washers,
spacers, and cylinder head capscrews.
If the tool is not aligned correctly it will not turn after the
capscrews are torqued.
On blocks with a double undercut radius the tool bit must

be adjusted so it is in the radius.
Use the stop collar to raise the tool bit off the counterbore
ledge 0.025 mm to 0.25 mm [0.001 inch to 0.010 inch].
The tool must be off the ledge enough to allow the bit
extension device to work.
ProCarManuals.com
Use a 3/32 inch hex wrench. Loosen the tool bit locking
screws ONLY enough to allow the extension device to
function.
Use the 3/16 inch hex wrench. Turn the bit extension device
until the tool bit touches the I.D. of the large radius.
This must be done to be sure the large radius is extended
downward as the ledge is machined.
CAUTION
Do not turn the handle clockwise. The tool will damage
the bore.
Use the handle to turn the tool counterclockwise. Listen
for the sound of the tool bit scraping the bore wall as it is
turned a minimum of 180 degrees.
If the sound does not continue through 180 degrees, use
the bit extension device to push the tool bit against the bore
wall opposite the first position.
Turn another 180 degrees. Listen again for the sound of the
bit. Check for a burr if it touches at only one point.
CAUTION
Do not attempt to raise the cutter plate with the tool bit
extended into the double undercut radius.
Use a 3/32 inch hex wrench. Tighten the two tool bit locking
screws.
Turn the stop collar to lower the cutter plate so that the bit
touches the ledge.
ProCarManuals.com
ADJUSTING THE DEPTH OF MACHINING

Be sure the tool bit is seated on the counterbore ledge.
Results will be correct when several 0.05 mm to 0.08 mm
[0.002 to 0.003 inch] cuts are made. The tool bit will be
damaged by deep cuts. The surface finish will be too rough.
NOTE: Surface finish specification must be 80AA or better.
Be sure the tool bit is not raised.
Turn the stop collar clockwise to adjust the clearance.
Move a feeler gauge around the housing. Clearance must
be to specification at the closest point.
Tighten the thumb screw on the stop collar.

NOTE: Record the depth of each machining. The figures
are used to achieve the correct liner protrusion.
Apply downward pressure. Turn the handle clockwise.
Keep the tool bit against the ledge.
Machine the bore until the stop collar contacts the housing.
Not using pressure, spin the tool two or three times to
smooth the surface.
Machine the counterbore in several operations until the
maximum liner protrusion is achieved.
CAUTION
Loosen and retract the tool bit before attempting to
raise the tool.
Raise the cutter plate.
Remove the tool from the block.
Use a fine, India type stone. Remove any burrs and sharp
edges from the counterbore ledge.
CAUTION
Be sure the micrometer does not contact the radius on
a block that does not contain a double undercut count-
erbore radius.
Use a depth micrometer. Measure the counterbore depth
in the four places shown.
The four measurements must not vary more than 0.25 mm
ProCarManuals.com
[0.001 inch]. If the measurements exceed the specification,

the counter bore ledge must be machined again.
CAUTION
Be sure that the indicator does not contact the count-
erbore radius on a block that does not have a double
undercut.
Use a gauge block, Part No. 3823495. Measure the angle
of the counterbore ledge at four equally spaced points.
The measurement of the ledge depth must be taken as
near to the counterbore radius as possible, and as near to
the counterbore edge as possible.
The angle (12) is OK if the measurement that is near the

counterbore edge is the same or no more than 0.036 mm
[0.0014 inch] shorter than the measurement near the count-
erbore radius.
Machine the ledge again if the measurement near the
counterbore edge is longer than the measurement near the
radius.
Check the counterbore for cracks.

NOTE: Liners and sealing ring(s) must be identified by
cylinder number for proper assembly.
Measure the liner flange thickness at four equally spaced
points around the flange.
Cylinder liner protrusion (A) is the total sum of the liner

flange thickness and sealing ring(s) thickness, minus the
depth of the counterbore.

mm in
0.08 MIN 0.003
0.13 MAX 0.006
ProCarManuals.com
MACHINE FOR OVERSIZE LINERS

Tools required for this procedure are listed below. They are
available separately or in the kits.
LINER COUNTERBORE TOOL KIT, PART NO. ST-1168
1. Main Housing Assembly, Part No. ST-1168-1
8. 3\32 inch Hex Key, Part No. ST-1168-57, or equivalent
9. 5/32 inch Hex Key, Part No. ST-1168-59, or equivalent
10. 3/16-inch Hex Key, Part No. St-1168-60, or equivalent
LINER COUNTERBORE SALVAGE TOOL KIT, PART NO.
3375820
2. Base Plate, Part No.3375827
3. Cutter Plate Assembly, Part No. 3375821
4. Micrometer Assembly, Part No. 3375826
5. Setting Standard, Part No. 3375828
6. Cutter Assembly, Part No. 3822216
7. Depth Spacer Block, Part No. 3376189
11. Plain Washers, four, Part No. 3375830, or equivalent
ProCarManuals.com
[3/16-inch I.D.], [2-inch O.D.], Standard Adapters, Part

No. 3375829, or equivalent, 30.1625 mm I.D. 88.9 mm
long [13/16-inch I.D. 3.5 inch long]
The following are also required:
• Four capscrews from the cylinder head
• Drill Motor [10-ampere, 450 rpm, 19 mm [3/4 inch]
Chuck.
The user of the following instructions must have inspected the cylinder block.
Terms used in this Procedure must be understood.
NOTE: After machining both the upper and lower counterbore I.D. for oversized liners, you must machine the
counterbore ledge. Refer to Procedure, 001-058
These instructions cover the counterbore depth and the upper counterbore I.D. machining at the same time.
NOTE: Cummins Engine Company, Inc., recommends that the accuracy of the tool be checked before machining the
customer’s block. If possible, machine a scrap block and check the accuracy of the cut.
If a scrap block is not available, adjust the tool to machine a size smaller than required. Check the accuracy of the
cut. Make final adjustments before machining to specification.
NOTE: The cylinder liner I.D. is the same on oversize liners as that of the standard liner.
NOTE: On all QSK19 blocks the upper counterbore I.D. must be no less than 0.025 mm [0.001 inch] smaller, and no
more than 0.076 mm [0.003 inch] larger than the O.D. of the cylinder liner upper flange diameter.
Install the base plate to the main housing. Install the four
capscrews.
Position the cutter plate assembly with the tapered edge
away from the housing. Align the keyway in the plate with
the key in the shaft.
Install the cutter plate. Install the washer and nut.
CAUTION
Damage to the cylinder block or interference with the
cylinder liner will result if the wrong cutter assembly is
used.
The illustration shows the cutter that must be used with the
QSK19 cylinder block.
ProCarManuals.com
ADJUST THE SET SCREW

Put the cutter in the cutter plate assembly. Tighten the set
screw until it becomes difficult to slide the cutter in the
groove.
Remove the cutter assembly.
Measure the counterbore I.D. and depth. Refer to Proce-

dure No.
CAUTION
The top of the cylinder block must be clean and free of
burrs. The tool must be flat on the block surface to
machine the counterbore I.D. correctly.
INSTALL THE TOOL

To “LOCK” the feed mechanism, turn the knob on top
clockwise.
To “UNLOCK” the feed mechanism, turn the knob coun-
terclockwise.
Put the tool on the block.
“UNLOCK” the feed mechanism.

Lower the cutter plate until it contacts the lower counter-
bore I.D. This will center the tool in the bore.
Be sure the base plate does not rock.
Rotate the base plate until the bolt holes align with the
cylinder head mounting capscrew locations.
Install the four capscrews, plain washers, and standard
ProCarManuals.com
adapters.
ADJUST THE CUTTER ASSEMBLY

Use the setting standard, Part No. 3375828. Use the mi-
crometer assembly, Part No. 3375826.
Put the setting standard in the micrometer as shown. Mea-
sure the length of the standard. In this example, the mi-
crometer reads 193.04 mm (7.600 inch).
If the reading does not agree with the value stamped on the
setting standard,
• loosen the set screw (1),
• move the end post (2),
• tighten the set screw (1).
Set the micrometer to the correct dimension for the block

being machined.
Put the cutter assembly in the micrometer as shown.
Use a hex key. Loosen the set screw on the cutter assem-
bly. Move the spring loaded plunger until it contacts the
micrometer.
Tighten the set screw.

Move the micrometer to check the setting.
Repeat the setting process until the cutter assembly is
accurately set.
ADJUST MACHINING DEPTH

Raise and “LOCK” the drive assembly.
Put the cutter assembly in the cutter plate. It must extend
a minimum of 6 mm [1/4 inch] over the edge of the count-
erbore.
Tighten the top set screw for the cutter bit.
ProCarManuals.com
On QSK19 cylinder blocks use depth spacer block, Part

No. 3376189.
NOTE: The depth spacer block is contained in the liner
counterbore salvage tool kit, Part No. 3375820.
“UNLOCK” the drive mechanism. Lower the cutter plate

until the cutter touches the block.
Put the depth spacer block, Part No. 3376189, on the tool.
The depth of cut dimension must be visible [as shown].
Turn the stop collar until it touches the depth spacer block
as illustrated.
NOTE: The 0.522 inch depth spacer block is shown as an
example ONLY.
FINAL ADJUSTMENTS FOR DEPTH

The style of the block being machined determines the next
adjustment.
CAUTION
Do not cut the counterbore depth with this tool.
Follow these instructions for the QSK19.
Turn the depth stoop collar 1/2 of a turn (180 degrees)
counterclockwise. The cutting assembly must be raised
slightly from the counterbore ledge.
ProCarManuals.com
Use a hex key. Tighten the set screw on the collar.
MACHINE THE COUNTERBORE I.D.

CAUTION
Be sure no dirt or chips are in the cutting assembly
groove of the cutter plate.
Raise the cutting plate assembly. “LOCK” the drive mecha-
nism.
Push the cutting assembly into the cutter plate until it
touches the shaft.
Use a hex key. Tighten the setscrew.
WARNING
Hold the drill firmly. The drill will be hard to hold when
the tool first contacts the block.
Lower the cutting plate until the cutting assembly is 1.50
mm [1/16-inch] above the block. “LOCK” the drive mecha-
nism.
Install the universal drive (14) in the drill.
NOTE: The feed mechanism will automatically control the
rate that the cutter is lowered.
START the drill. The cutter plate will freewheel after the
depth stop collar has contacted the drive unit.
STOP the drill after the cutter has free wheeled for five to
ten revolutions.
Remove the drill.
“UNLOCK” the drive mechanism.

Raise the cutter plate.
“UNLOCK” the drive mechanism.
Use a hex key. Loosen the set screw.
ProCarManuals.com
Remove the cutter assembly.
Remove the mounting capscrews, adapters, and washers.

Remove the tool.
Use a hone stone. Remove burrs from the sharp corner of

the I.D.
Measure the upper counterbore I.D. (1) in the location
shown.
Machine the diameter again if the I.D. is smaller than
specification.
Machine the block for the next larger size liner when the
I.D. is larger than specification.
Check the concentricity between the upper counterbore

I.D. (1) and the packing ring bore (4).
Clean the cylinder block. Refer to Procedure No. 001-026
ProCarManuals.com
LINER BORE CONCENTRICITY

Check the concentricity after the repair of the upper count-
erbore I.D. or the packing ring bore I.D.
Use the concentricity gouge, Part No. ST-1252.
Adjust the contact pins (3) to be as close to the plate as

possible. If necessary,
• Remove the set screw (2),
• Remove the plate,
• Turn the plate over,
• Install the plate,
• Install the set screw.
Loosen the indicator arm set screw (1). Move the indicator
arm until the distance between the contact pins and the
indicator (5) is 254 mm [10 inch].
Loosen the contact plate set screw (2). Slide the contact
plate as far toward the indicator arm as possible.
Loosen the adjusting knob (4).
CAUTION
The upper counterbore and the top surface of the block
must be clean.
Put the tool in the cylinder block liner bore to be checked.
Slide the contact plate until both contact pins touch the
upper counterbore I.D.
NOTE: The indicator must not touch the packing ring bore
at this time.
Hold both contact pins against the upper counterbore I.D.

Slide the base until the indicator tip touches the packing
ring bore I.D. Continue to slide the base until the indicator
needle has moved 0.0064 mm to 0.254 mm [0.005 inch to
0.010 inch].
Hold the tool in place and tighten the contact plate set
screw (2).
ProCarManuals.com
Hold the contact pins against the upper counterbore I.D.

Turn the adjusting knob to move the indicator needle a
minimum of one revolution. Turn the knob until the needle
indicates “ZERO”.
Slide the tool until the indicator is not touching the block.
Slide the tool backward until both contact pins touch the
upper counterbore I.D. The indicator must remain at
“ZERO”.
Repeat this step until the indicator continues to read “ZERO”
after the tool is moved.
Turn the tool 180 degrees from the “ZERO” position. Slide
the tool until both contact pins touch the upper counterbore
I.D.
Read the indicator. the bore run out is one-half of the
indicator reading.
EXAMPLE:
Indicator reading of 0.2032 mm (0.008 inch)
Actual run out is 0.1016 mm (0.004 inch)
Liner Bore Run Out

mm in
0.130 MAX 0.005
Cylinder Liner Protrusion (001-064)
Move the tool 180 degrees backward to the original

“ZERO” position.
Repeat the measurement procedure when the indicator
does not read “ZERO”.
CAUTION
Concentricity must be within specification. Engine dam-
age will result when the liner is not seated correctly in
the bore.
Turn the tool until the contact pins are 90 degrees coun-
terclockwise from the original “ZERO” position. Adjust
the indicator to “ZERO” position.
ProCarManuals.com
Read the indicator. Compare the reading to the specifica-

tion.
Repeat this procedure until consistent readings are ob-
tained.
NOTE: The bore must be repaired when consistent read-
ings are not obtained. Refer to the Alternative Repair
Manual, Bulletin No. 3379035.
Cylinder Liner Protrusion (001-064)

Adjust
If the liner protrusion is not correct, the liner must be
removed.
If liner protrusion needs increased add more sealing rings
or a thicker sealing ring.
If liner protrusion needs decreased machine the counter-
bore ledge. Refer to Procedure No. 001-058.
Gear Cover Accessory Drive Bushing (001-066)
Gear Cover Accessory Drive Bushing

(001-066)
Remove
Use the appropriate bushing mandrel and an arbor press.
Remove the accessory drive, water pump, and the hydrau-
lic pump drive bushings.
Measure the bore I.D. Replace the front cover when any
bore I.D. is not within specifications.
Front Cover Bushing Bore I.D.

mm in
Accessory and Wa- 43.078 MIN 1.696
ter Pump Drive
43.104 MAX 1.697
Hydraulic Pump 41.275 MIN 1.625
Drive
41.301 MAX 1.626
Install
Use the appropriate bushing mandrel, install the accessory
drive, water pump and hydraulic pump.
Use a mallet or an arbor press. Install the bushings.
ProCarManuals.com
QSK19
Section 2 - Cylinder Head - Group 02 Page 2-a
Section 2 - Cylinder Head - Group 02

Section Contents
Page
Crosshead ........................................................................................................................................................ 2-4
Clean ........................................................................................................................................................... 2-4
Cylinder Head .................................................................................................................................................. 2-5
Assemble ................................................................................................................................................... 2-14
Clean ........................................................................................................................................................... 2-6
Disassemble ............................................................................................................................................... 2-13
Exploded View .............................................................................................................................................. 2-5
Pressure Test ............................................................................................................................................... 2-8
Vacuum Test ............................................................................................................................................... 2-10
Cylinder Head - General Information .............................................................................................................. 2-1
Cylinder Head Injector Bore .......................................................................................................................... 2-15
Adjust ......................................................................................................................................................... 2-17
Service Tools ................................................................................................................................................... 2-2
Cylinder Head ............................................................................................................................................... 2-2
ProCarManuals.com
Valve, Cylinder Head ...................................................................................................................................... 2-22

Grind .......................................................................................................................................................... 2-24
Install ......................................................................................................................................................... 2-26
Lap ............................................................................................................................................................ 2-26
Remove ...................................................................................................................................................... 2-22
Valve Guide, Cylinder Head ........................................................................................................................... 2-18
Clean ......................................................................................................................................................... 2-18
Inspect ....................................................................................................................................................... 2-19
Install ......................................................................................................................................................... 2-19
Remove ...................................................................................................................................................... 2-18
Valve Seat Bore.............................................................................................................................................. 2-20
Initial Check ............................................................................................................................................... 2-20
Valve Seat Insert, Cylinder Head................................................................................................................... 2-20
Grind .......................................................................................................................................................... 2-21
Install ......................................................................................................................................................... 2-21
Remove ...................................................................................................................................................... 2-20
QSK19 Cylinder Head - General Information
Section 2 - Cylinder Head - Group 02 Page 2-1
Cylinder Head - General Information

General Information
The QSK19 uses a torque-turn method for torquing all
cylinder head capscrews. This method provides better con-
trol of the load on the capscrews.
The QSK19 utilizes a stemless crosshead design. This

design does not require adjustment.
The QSK19 cylinder head gasket has been altered due to
changes to the shape of the push tube hole. The grommets
have been built into the gasket.
ProCarManuals.com
Service Tools QSK19
Page 2-2 Section 2 - Cylinder Head - Group 02
Service Tools
Cylinder Head

Cylinder Head Capscrew Length Gauge
Used to check the length of the cylinder head capscrews.
3824955
ProCarManuals.com
Valve Spring Compressor

Compress the valve spring to allow the valve to be removed or
installed.
ST-448
Valve Spring Compressor

Compress the valve spring to allow the valve to be removed or
installed. This tool is air-operated.
3375960
Hydrostatic Tester
Check for coolant leaks in the cylinder head. Requires shop air,
a lifting hoist, a water tank, and the appropriate Test Adapter Plate
ST-1012
and o-ring.
Water Test Plates

Check for coolant leaks in the cylinder head. Use with Part No.
ST-1012 Hydrostatic Tester. Use with Part No. 3375071 Water Test
3375070
Plate O-rings.

Measure cylinder liner counterbore ledge angle and injector pro-
trusion.
3823495
QSK19 Service Tools

Valve Seat Grinding Machine
Used to grind the valve seats.
ST-685
Valve Vacuum Tester

Used to test the valve to valve seat connection.
ST-1257
Valve Seat Extractor

Used to remove the valve seats.
ST-1323-1-Exhaust
3376799-Intake
ProCarManuals.com
Valve Spring Tester

Used to test the valve springs.
3375182
Valve Lapping Compound

An abrasive compound used to lap the valves.
3375805
Valve Head Thickness Gauge

Used to check the intake and exhaust valve head thickness after
reconditioning.
3824861
Crosshead (002-001) QSK19
Crosshead (002-001)
Clean
WARNING
cleaning, follow the manufactures recommendations
personal injury.
Use solvent. Clean the parts.
Inspect for Reuse

Check the contact pad (shaded area) for cracks.
Check the valve stem contact area for wear or damage.
ProCarManuals.com
QSK19 Cylinder Head (002-004)
Cylinder Head (002-004)

Exploded View
ProCarManuals.com
1. Screw, Twelve Point Cap 11. Insert, Valve, Intake

2. Gasket, Cylinder Head 12. Plug, Expansion
3. Seal, Valve Stem 13. Plug, Expansion
4. Collet, Valve 14. Plug, Expansion
5. Valve, Exhaust 15. Plug, Threaded
6. Valve, Intake 16. Plug, Threaded
7. Rotator, Valve 17. Head, Cylinder
8. Spring, Valve 18. Guide, Valve Stem
9. Pin, Groove 19. Retainer, Valve Spring
10. Insert, Valve, Exhaust 20. Plug, Pipe
Cylinder Head (002-004) QSK19
Clean
WARNING
personal injury.
Clean the heads with solvent.
Check for broken springs or other damage.
Inspect for Reuse

Check for cracks on the combustion surface.
NOTE: If a crack around the injector bore exceeds the
maximum length, the cylinder head must be replaced.
Allowable Crack Length

mm in
6 MAX 0.25
ProCarManuals.com
NOTE: Both ends of a crack between the valve must be

visible. If one end of a crack extends into the valve seat bore
(behind the valve seat), the condition of the cylinder is
questionable. To be sure that the cylinder head is reusable,
remove the valve and valve seat.
Use a depth gauge, Part No. 3823495, or equivalent. Mea-

sure the valve head depth.
NOTE: If the valve depth exceeds specifications, the cyl-
inder head must be rebuilt.
Allowable Valve Depth from the Combustion Face

mm in
0.00 MIN 0.000
0.51 MAX 0.020
Use a straight edge to measure the flatness of the head

gasket surface.
The head must be resurfaced if a feeler gauge larger than
0.08 mm (0.003 in) will fit between the straight edge and the
cylinder head.
The head can be resurfaced as long as the head thickness
measurement is within specifications.
Minimum Head Thickness (1)

mm in
150.114 MIN 5.910
NOTE: If the head is resurfaced, be sure that the injector
protrusion and the valve depth in the head are adjusted
properly.
Using flange head capscrews with the torque plus angle

method of installation, places the capscrew beyond the
yield point and permanently stretches the capscrew. These
capscrews can be reused throughout the life of the engine
unless the capscrew exceeds the specified free length.
The free length must be checked to avoid bottoming in the
block during installation.
Cylinder head capscrew length gauge, Part No. 3824955,
has been developed to check capscrew free length.
To check the capscrew free length, place the head of the

capscrew in the slot, with the flange against the base of the
slot.
ProCarManuals.com
If the end of the capscrew touches the foot of the gauge,

the capscrew is too long and must be discarded.
If there is clearance between the end of the capscrew and

the bottom base of the tool, the capscrew is OK for reuse.
The capscrew can also be checked using a set of calipers.

The maximum allowable free length is measured from the
bottom of the flange to the end of the capscrew (Dimension
X).
Cylinder Head Capscrew Free Length

mm in
207.3 MAX 8.160
Pressure Test
Remove the valves. Refer to Procedure No. 002-020.
ProCarManuals.com
Use a hydrostatic tester, Part No. ST-1012, with water test

adapter plate, Part No. 3375070, to test the cylinder head.
Remove one of the two plugs from the pressure regulator.

Install the pressure gauge in the regulator.
Turn the adjusting knob on the regulator counterclock-
wise as far as it will turn.
Install the pressure regulator between the air supply and

the quick disconnect fitting.
NOTE: The arrow on the top of the pressure regulator must
point in the direction of the air flow (toward the quick dis-
connect fitting).
Use adapter plate (4), Part No. 3375070, and plate (5), Part
No. 3375071, to test the head.
ProCarManuals.com
With the head as shown, assemble the adapter plates. The

guide pins on the lower plate (5) must go in the water
passages. The o-ring on the upper plate (4) creates a seal
on the upper water passage. The other end of the plate
goes into the injector bore.
Put the clamping assembly (1) over the head and adapters.
The guide pins on the clamp must go into the holes in the
lower adapter plate.
Tighten the clamp on the head.
Connect the wire hose to the upper adapter fitting.
Attach the lifting arm (2) to the clamp assembly with the
lock pins.
NOTE: One mounting location on each piece is color-coded
red.
Adjust the air pressure.
Air Pressure
kPa psi
552 MAX 80
Lower the head into a tank of water.
Bubbles will indicate an air leak.
If the cylinder head leaks, it must be repaired or replaced.
ProCarManuals.com
Install the cylinder head valves. Refer to procedure No.

002-020.
NOTE: Thoroughly lubricate the valve guide I.D. with 140
wt. gear oil before installing the valves.
Vacuum Test
The valve and the valve seats must be clean and dry.
NOTE: The valve vacuum tester, Part No. ST-1257 can be
used to test all Cummins’ engine models.
Choose the correct cup for the engine model that is to be
tested.
Chose the correct seal.

1. Intake valve
2. Exhaust valve
NOTE: A new seal is available that has the appearance of
(1), but is manufactured from a softer material. The new
seal is to be used on cylinder heads that are machined with
a relief valve between all four bores.
Install the seal and the cup to the vacuum line (hose).
ProCarManuals.com
Cover the valve with the cup and the seal. The seal must
have a tight contact on the cylinder head around the valve.
To check the exhaust valves, the seal must completely fill
the milled area between the exhaust valves.
Move the toggle switch (3) to the “ON” position.

Turn the vacuum control valve (4) to the “OPEN” position.
When the gauge indicates between 20 in-Hg and 25 in-Hg,

turn the vacuum control valve (4) to the “CLOSED” or
“OFF” position.
Turn the toggle switch (3) to the “OFF” position.
Use a stop watch. As the vacuum gauge needle moves

counterclockwise, start the timing when the needle on
the gauge points to 18 in-Hg.
Stop the timing when the needle on the gauge points to 8
in-Hg.
The elapsed time for the gauge to move between the speci-
fied readings must be 10 seconds or more.
If the elapsed time is less than 10 seconds, perform the
ProCarManuals.com
following checks:
• Repeat the test to be sure the equipment is func-
tioning properly.
• Use a mallet to hit the valve stem lightly to be sure
the valve is sealing. Repeat the test.
• Apply a thin coating of grease on the O.D. of the
insert and the valve head. Repeat the vacuum test.
The grease pattern will show the point of leakage.
• If the leakage is between the insert and the head,
the insert must be replaced. Refer to Procedure
No.002-019.
CAUTION
The cylinder head must be disassembled and cleaned
after any grinding or cutting procedures.
If the leakage is between the valve and the insert, one of
the following procedures must be performed:
• Lap Valves to Seat Procedure No. 002-020
• Grind the Valves Procedure No. 002-020
• Grind the Valve Seat Procedure No. 002-019
Disassemble
CAUTION
The valve springs are under compression. Be cautious
when using the valve spring compressor. Personal in-
jury can result if the tool slips from your hands.
Use a valve spring compressor, Part No. ST-448, or Part
No. 3375960, or the equivalent. Valve spring stand, Part
No. ST-1022, and the compressor plate, Part No. 3375043
can be used to compress all four springs at the same time.
NOTE: Mark the valves for location prior to removal. The
intake and exhaust valves are different. This practice will
aid the assembly procedure.
Remove the parts.
1. Collet, Valve
2. Retainer, Valve Spring
3. Spring, Valve
4. Guide Valve Spring/Rotator Valve
5. Valve
Discard the valve springs, collets and valve rotators.
ProCarManuals.com
Refer to Procedure No. 002-004.
Use a drill, a sheet metal screw, and the following parts

from the light duty puller kit, Part No. 3375784, to remove
the cup plugs.
• Slide Hammer
• Hook
Remove and discard the 10 cup plugs.

NOTE: Cup plugs must be removed from the head casting
for cleaning purposes.
Assemble
Use cup plug LoctiteT sealant, Part No. 3375068.
NOTE: Use the correct expansion plug driver to make sure

the expansion plugs are installed to the correct depth in the
cylinder head. Drive the plug until the shoulder of the driver
contacts the cylinder head.
• Part No. 3376813 Expansion Plug Driver
• Part No. 3376814 Expansion Plug Driver
NOTE: A cup plug driver handle, Part No. 3376795, must
be used with Part No. 3376813 and Part No. 3376814
Expansion Plug Driver.
ProCarManuals.com
Install 10 new cup plugs.
Use a hydrostatic tester to check for evidence of leaks

around cup plugs. Refer to the Procedure No. 002-004.
NOTE: When turning the rotator by hand, it may turn roughly,

appear difficult to turn, or not turn at all. This is normal until
the rotator is installed, after installation it will rotate freely.
The rotator must be soaked in clean engine oil for at least
15 minutes prior to installation.
The rotator must be installed over the valve guide with the
spring pilot flange face-up as shown in this illustration.
QSK19 Cylinder Head Injector Bore (002-011)
CAUTION
The valve springs are under compression. Be cautious
jury can result if the tool slips from your hands.
No. 3375960, or equivalent. Valve spring stand, Part No.
ST-1022 and compressor plate, Part No. 3375043 can be
used to compress all four springs at the same time.
Install the parts.
1. Valve
2. Rotator, Valve
3. Spring, Valve
4. Retainer, Valve Spring
5. Collet, Valve
NOTE: Thoroughly lubricate the valve guide I.D. with 140
wt. gear oil before installing the valves.
Use a valve vacuum tester, Part No. 3824277, or equiva-

lent.
If the valve to the valve seat contact pattern looks OK and
the valve still does not pass the vacuum test, perform the
following check.
ProCarManuals.com
Apply a thin coating of grease on the outside diameter of

the insert and the valve head. Repeat the vacuum test. The
grease pattern will show the point of leakage.
If the leakage is between the insert and the valve, refer to
the Procedure No. 002-020.
If the leakage is between the insert and the head, the insert
must be replaced. Refer to the Procedure No. 002-019.
Cylinder Head Injector Bore (002-011)

Inspect for Reuse
Inspect the injector bore for cracks or other damage.
Cylinder Head Injector Bore (002-011) QSK19
Use a dummy injector with no injector o-rings installed.
Use Prussian Blue™, apply a thin coating on the sealing

ring.
ProCarManuals.com
CAUTION
Support the cylinder head to prevent damage to the
injector tip that protrudes from the combustion face.
Install the injector and injector hold down clamp.
Tighten the hold down clap capscrew.
QSK19 Cylinder Head Injector Bore (002-011)
Adjust
Use a gauge block, Part No. ST-547, or equivalent to mea-
sure the injector protrusion.
Measure as shown.
Injector Protrusion
mm in
2.42 MIN 0.095
2.92 MAX 0.115
If the protrusion is not within specifications, use an oversize
sealing ring. Sealing rings are available in various sizes.
Injector Sealing Rings

mm in
Wall Thickness 0.343 MIN 0.0135
0.419 MAX 0.0165
Protrusion Change 0.00 NOMINAL 0.000

0.546 MAX 0.0215
ProCarManuals.com

0.673 MAX 0.0265

0.800 MAX 0.0315
NOTE: * The 0.343/0.419 mm (0.0135/0.0165 in) is the
standard sealing ring.
Remove the injector hold down clamp capscrew.

Remove the injector and injector hold down clamp.
Valve Guide, Cylinder Head (002-017) QSK19
Inspect the contact pattern in the injector bore. A blue band

1.52 mm (0.060 in) wide and 360 degrees full circumfer-
ence minimum must be visible.
NOTE: If the pattern does not meet the specification, clean
the injector bore with a tapered brush. Inspect the seating
pattern again. The cylinder head must be replaced or
repaired if it is not within specifications.
Valve Guide, Cylinder Head (002-017)

Inspect for Reuse
Inspect the valve guides for chips and cracks.
Use a ball gauge or a dial bore indicator to measure the I.D.
of the valve guides.
Measure the I.D.
ProCarManuals.com
Valve Guide I.D. (Installed)

mm in
10.551 MIN 0.4154
10.589 MAX 0.4169
Remove
CAUTION
If a valve guide is replaced, the valve seat insert for the
valve guide must be ground, or severe engine damage
could result.
NOTE: ONLY replace the valve guide if it is not within
specifications.
Use an arbor press and a suitable mandrel (1), to remove
the worn valve guide (2).
Clean
WARNING
personal injury.
Use solvent to clean the valve guide bores.
QSK19 Valve Guide, Cylinder Head (002-017)
Inspect
Measure the I.D. of the valve guide bore.
Valve Guide Bore I.D.

mm in
21.438 MIN 0.8440
21.463 MAX 0.8450
If the bore is not within specifications, ream the bore for
oversize valve guides.
NOTE: Valve guides are available in two oversizes; 0.25
mm (0.010 in) and 0.38 mm (0.015 in). Ream the valve
guide bore to maintain a press fit within 0.028 mm and
0.067 mm (0.0011 in and 0.0026 in) between the valve
guide and the valve guide bore.
Install
CAUTION
Make sure the mandrel does not damage the top of the
valve guide. If the guide is damaged, the valves may
stick causing severe engine damage.
Use an arbor press and a suitable mandrel (6), to install the
valve guide.
ProCarManuals.com
NOTE: The QSK19 only uses the flat top style valve guides
with a valve seal.
Install the valve guide (7) to the specified height.
Valve Guide Height (to Spring Pocket)

mm in
37.97 MIN 1.495
38.48 MAX 1.515
Valve Guide Height (to Top of Head)

mm in
13.97 MIN 0.550
14.47 MAX 0.570
Install the valve guide (7) to the specified height.
Valve Guide Height (to Spring Pocket)

mm in
37.97 MIN 1.495
38.48 MAX 1.515
Valve Guide Height (to Top of Head)

mm in
13.97 MIN 0.550
14.47 MAX 0.570
Valve Seat Bore (002-018) QSK19
Valve Seat Bore (002-018)

Initial Check
With the valve seats removed, measure the I.D. and the
depth of the insert bore in the head
Valve Seat Bore Measurements

mm in
Intake Diameter 60.37 MIN 2.377
60.40 MAX 2.378
Intake Depth 13.00 MIN 0.492
13.13 MAX 0.497
Exhaust Diameter 60.37 MIN 2.377
60.40 MAX 3.378
Exhaust Depth 12.50 MIN 0.492
12.62 MIN 0.497
If the I.D. is not within specifications, use an oversize seat.

NOTE: Oversize valve seat inserts are available in the
following sizes. Machine the valve seat insert bore in the
head. A press fit within 0.064 mm to 0.114 mm [0.0025 in
to 0.0045 in] between the valve seat insert and the valve
seat insert bore must be maintained.
ProCarManuals.com
O.D. Oversize Depth (Thickness)

Oversize
0.25 mm [0.010 inch] Standard
0.51 mm [0.020 inch] 0.13 mm [0.005 inch]
0.76 mm [0.030 inch] 0.25 mm [0.010 inch]
1.02 mm [0.040 inch] 0.38 mm [0.015 inch]
Valve Seat Insert, Cylinder Head

(002-019)
Remove
Use a valve seat grooving kit, Part No. 3376405, or equiva-
lent.
Machine a groove in the seat as close to the bottom of the
bore as possible. This will allow the valve seat extractor to
be used.
Use the specified valve seat extractor. Use an extractor

knocker assembly, Part No. 3376617.
• Exhaust seat = Part No. ST-1323–1 Extractor
• Intake seat = Part No. 3376799 Extractor
NOTE: ONLY the intake ports contain anti-swirl plates.
Discard the anti-swirl plate.
QSK19 Valve Seat Insert, Cylinder Head (002-019)
Install
Clean the valve seat insert bore.
Check the length of any cracks extending into the valve
seat insert bore.
NOTE: The cylinder head must be replaced if a crack
extends into the bottom of the bore.
NOTE: At times it is possible to remove the crack by ma-
chining the head to use an oversize valve seat insert.
Identify the correct valve seat insert.

• Top picture: Intake port seat.
• Bottom picture: Exhaust port seat.
Both the intake and the exhaust port seats must be in-
stalled with the 30 degree angle positioned as shown.
NOTE: Exhaust seats are color coded blue to identify the
30 degree angle side of the seat.
ProCarManuals.com
Use an arbor press, and a mandrel. Install the insert into

the head.
Grind
Use a valve seat grinding machine, Part No. ST-685, or
equivalent. Use a valve guide arbor set, Part No. 3375946,
or equivalent.
Grind the valve seat insert to the angle shown.
Measure the width.
Valve Seat Width

mm in
Intake 3.05 MIN 0.120
3.55 MAX 0.140
Exhaust 1.52 MIN 0.060
2.54 MAX 0.100
Valve, Cylinder Head (002-020) QSK19
If the width of the valve seat is not within specifications,

remove surface material on the I.D. and the O.D. to de-
crease the width of the seat.
NOTE: If the valve seat specifications are not obtained by
grinding, the insert must be replaced.
Measure the valve seat to the valve guide concentricity.

NOTE: The seat and guide must be concentric.
Valve Seat to Guide Concentricity

mm in
0.05 MAX 0.002
ProCarManuals.com
Valve, Cylinder Head (002-020)

Remove
CAUTION
The valve springs are under compression. Use caution
jury can result.
No. 3375960, or equivalent. Valve spring stand, Part No.
ST-1022, and the compressor plate, Part No. 3375043, can
be used to compress all four springs at the same time.
Mark the valve for location prior to removal. The intake and
exhaust valves are different. The practice will help with
future installation identification.
Compress the valve spring and remove the following parts.
1. Valve collets
2. Valve spring retainer
3. Valve spring
4. Valve rotator
5. Valve
6. Valve stem seal
Discard the collets.
QSK19 Valve, Cylinder Head (002-020)
Inspect for Reuse

Inspect the collet grooves for wear.
Measure the O.D. of the valve stem.
Valve Stem O.D.

mm in
10.490 MIN 0.4130
10.510 MAX 0.4138
Use a valve head checking tool, Part No. 3824861, to mea-

sure the head thickness of the valve.
Position the tool over the valve, place on a flat surface, if
the bottom of the tool touches the flat surface the valve
must be replaced.
ProCarManuals.com
If a valve head checking tool is not available, put the valve

on a flat surface. Check the height of the O.D.
Valve Head Thickness (at the O.D.)

mm in
3.94 MIN 0.155
NOTE: This type of a check is not as accurate as using the
valve head checking tool.

CAUTION
Always demagnetize and clean the parts thoroughly
after a magnetic particle inspection. The iron fragments
can damage the internal engine components.
Use the magnetic particle residual method. Check the
valves for cracks.
NOTE: Check the intake valves with the coil and head
shot methods (the coil shot first). Check the exhaust valves
with the coil shot method.
Use a 305 mm [12 in] minimum diameter coil.
Coil Shot Amperage

(Ampere Turns)
MIN 400 D.C. or rectified A.C.
MAX 800 D.C. or rectified A.C.
NOTE: An ampere turn is an electrical current of one am-
pere flowing through the coil, multiplied by the number of
turns in the coil.
NOTE: A broad fuzzy pattern will appear at the welded joint
on the exhaust valves. This is normal. If there is a distinct
line in the broad fuzzy pattern, the valve must be replaced.
Head Shot Amperage

(Ampere)
ProCarManuals.com
Acceptance Criteria (Intake and Exhaust Valves.

(1). Indications less than 38.1 mm [1.5 in] in length are
acceptable. More than five indications, spaced closer
than 3 mm [0.118 in], are not acceptable.
(2). No indications are acceptable.
(3). ONLY longitudinal indications are acceptable.
(4). ONLY longitudinal indications are acceptable.
(5). No indications are acceptable.
Grind
Use Scotch-BriteT, Part No. 3823258, to clean the valve
stems. Clean the valve stems. Clean the carbon deposits
from the valve face and the head
NOTE: The valves must be clean and free of carbon de-
posits before they are ground. Valves can be cleaned by the
bead blasting method in the head area only.
Use a valve facing machine, Part No. 3376256 or equiva-

lent, to grind the face of the valve.
NOTE: Follow the instructions supplied with the valve fac-
ing machine for the correct setup before grinding the valves.
Use solvent to clean the metal particles from the valve.

ProCarManuals.com
Use a valve head checking tool, Part No. 3824861, to mea-

sure the head thickness of the valve.
Position the tool over the valve, place on a flat surface, if
the bottom of the tool touches the flat surface the valve
must be replaced.
Use a lead pencil or DykemT to mark across the valve face

as shown. Install the valve in the valve guide.
Hold the valve against the valve seat, and rotate the valve
backward and forward three or four times.
Correct contact against the valve seat will break the marks
on the valve face.
NOTE: Valves and valve seats that are correctly machined
do not require the use of lapping compound to make an air
tight seal. If lapping compound is required, inspect the
adjustments of the facing machine and the condition of the
grinding stone.
Lap
Use a fine lapping compound, Part No. 3375805, or equiva-
lent. Apply a thin and even coating on the valve.
Use a power or a hand suction lapping tool to provide
pressure in the center of the valve.
Turn the valve backward and forward. Continue lapping
until the compound shows a continuous contact pattern on
both the valve seat insert and the valve.
CAUTION
Lapping compound is an abrasive material. Failure will
result if the cylinder head, the valves, and the valve
seats are not cleaned thoroughly.
Clean the lapping compound from the parts.
ProCarManuals.com
Install
CAUTION
Lubricate all the valve guide bores and valve stems with
140W oil. Failure to lubricate guide and stems will result
in premature valve guide wear.
Install the seal driver (6) on the valve guide. Push the seal
(7) over the seal driver and on the valve guide. Push the
seal down on the guide until the lower spring is in the
groove on the guide.
Remove the seal driver.
Install the valves.
CAUTION
The valve springs are under compression. Use caution
jury can result.
No. 3375960, or equivalent. Valve spring stand Part No.
ST-1022 and the compressor plate, Part No. 3375043, can
be used to compress all four springs at the same time.
NOTE: The valve rotator must be soaked in clean engine
oil for at least 15 minutes prior to installation.
Install the following parts:
6. Valve stem seal (already installed)
5. Valve
4. Valve rotator
3. Valve spring
Compress the valve spring and install the following parts:
2. Valve spring retainer
1. New valve collets
ProCarManuals.com
NOTES
ProCarManuals.com
Section 3 - Rocker Levers - Group 03 Page 3-a
Section 3 - Rocker Levers - Group 03

Section Contents
Page
Crankcase Breather (External)......................................................................................................................... 3-4
Clean ........................................................................................................................................................... 3-5
Install ........................................................................................................................................................... 3-6
Remove ........................................................................................................................................................ 3-4
Rocker Lever .................................................................................................................................................... 3-7
Assemble ..................................................................................................................................................... 3-9
Disassemble ................................................................................................................................................ 3-7
Magnetic Crack Inspect ................................................................................................................................ 3-8
Rocker Lever Assembly.................................................................................................................................. 3-10
Assemble ................................................................................................................................................... 3-14
Clean ......................................................................................................................................................... 3-12
Disassemble ............................................................................................................................................... 3-13
Exploded View ............................................................................................................................................ 3-10
Rocker Lever Bushings.................................................................................................................................. 3-14
Install ......................................................................................................................................................... 3-14
Remove ...................................................................................................................................................... 3-14
Rocker Lever Cover........................................................................................................................................ 3-15
Clean ......................................................................................................................................................... 3-15
ProCarManuals.com

Rocker Lever Housing.................................................................................................................................... 3-15
Assemble ................................................................................................................................................... 3-16
Clean ......................................................................................................................................................... 3-15
Rocker Levers - General Information............................................................................................................... 3-1
Service Tools ................................................................................................................................................... 3-2
Rocker Levers ............................................................................................................................................... 3-2
Rocker Levers - General Information
Section 3 - Rocker Levers - Group 03 Page 3-1
Rocker Levers - General Information

General Information
The QSK19 utilizes the Outer Base Circle (OBC) overhead
set procedure.
NOTE: The OBC procedure requires the use of an accurate
inch-pound torque wrench. Torque wrench kit, Part No.
3824783, is available. A dial-type torque wrench with a
range from 0 to 35 N•m [0 to 300 in-lb] is required. The
torque wrench needs to be checked on a routine basis for
proper calibration. Use of a clicker-type torque wrench is
not recommended.
The QSK19 valve rocker lever incorporates a ball and socket

to minimize crosshead wear and reduce tipping of the
valves.
NOTE: The intake and exhaust rocker levers are not in-
terchangeable.
Both the intake and the exhaust levers contain a blind rivet
and the injector lever contains a plug ball. The rivets and
plug ball plugs, plug the oil drilling in the lever. The rivets
ProCarManuals.com
and plug ball plug must be present.

NOTE: All of the rocker levers contain replaceable bushings.
The rocker lever covers are available with and without

crankcase breathers.
The engine should have 3 breathers, but the locations may
vary. The rocker covers without breathers should have a
service plug (for the injector cut out tool) installed.
Rail Applications
The QSK19 Rail Engine uses a Mann & Hummel™ open
crankcase breather system. The two Mann and Hummel™
canisters (A) are mounted on a modified lubricating oil pan
adapter hand hole cover.
Service Tools
Page 3-2 Section 3 - Rocker Levers - Group 03
Service Tools
Rocker Levers

Torque Wrench Adapter
Secures the rocker lever adjusting screw while tightening the lock
nut.
ST-669
ProCarManuals.com
Water Tube Driver

Used to install or remove the water transfer tubes from the rocker
housings.
ST-1319
Torque Wrench
A dial-type torque wrench used to accurately adjust injectors in
inch-pounds. Use of a clicker-type torque wrench is not recom-
3824783
mended. 0-35 N•m [0-300 in-lb]

3375784
Torque Wrench
Inch-pound torque wrench used to tighten the valve lever ad-
justing screw. Does not require screwdriver attachment.
3376592
Valve Setting Gauge Kit

Kit contains two 25.4 mm [1 in] wide feeler gauges for centering
under the swivel foot of the rocker lever when setting the valves.
3824901 The kit contains an intake valve gauge at 0.36 mm [0.014 in] and
an exhaust valve gauge at 0.081 mm [0.032 in].
Service Tools

Rocker Lever Bushing Mandrel
Used to install and/or remove the rocker lever bushings
3162458
ProCarManuals.com
Crankcase Breather (External) (003-001)
Crankcase Breather (External)

(003-001)
Remove
Loosen the hose clamp at the breather vent tube.
Remove the tube support bracket capscrew and the bracket.
Remove the vent tube and the hose from the engine.
If the vent tube is blocked, it should be cleaned to prevent
excess crankcase pressure buildup.
Remove the following parts from the breather body (6).

1. Wing Nut
2. Washer
3. Breather Cap
4. Screen Mesh
5. Element
ProCarManuals.com
Remove the push nuts.

Remove the baffle.
CAUTION
The mandrel must make contact on the breather body
to prevent damage.
Use a water pump bearing separator, Part No. 3375326, or
equivalent. Support the cover as close as possible to the
breather to prevent cracking of the cover.
Push the breather out.
Rail Applications
Loosen the hose clamp and remove the crankcase breather
hose from breather canister.
Loosen the tube clamp between the breather canister and
the hand hole cover.
Remove the breather canister from the hand hole cover.
Clean
Use solvent to clean the inside of the crankcase breather
tube, and dry with compressed air.
Use air pressure to blow through the vent tube.
Replace the vent tube if it is clogged or dented.
ProCarManuals.com
Use solvent to clean the breather tube.
Clean the breather cap element and screens in an ap-

proved cleaning solvent.
Wipe out the breather housing (6).
Clean the following parts:
(4) Screen Mesh
(5) Element
(4) Screen Mesh
(3) Breather Cap
(2) Washer
(1) Wing Nut
Rail Applications
Loosen the hose clamp and remove the crankcase breather
hose from breather canister.
Check hose internally for obstructions or sludge buildup.
If the hose is blocked, clean it to prevent excess crankcase
pressure buildup.
Install the crankcase breather hose on the breather can-
ister. Tighten the hose clamp.
Install
Apply LoctiteT 732, or equivalent to the O.D. of the breather.
ProCarManuals.com
CAUTION
The mandrel must contact the breather body in the area
shown (2).
CAUTION
Excessive force will cause the aluminum cover to crack
(1).
Use a mandrel to install the breather.
Install the baffle and new push nuts.

Rocker Lever (003-008)
Install the parts in the following order:

(4) Screen Mesh
(5) Element
(4) Screen Mesh
(3) Breather Cap
(2) Washer
(1) Wing Nut
If the breather is not used, install the service plug and
o-ring.
Tighten the service plug.
Install the tube and hose on the engine.

Install the tube support bracket and capscrew.
Tighten the hose clamp at the breather vent tube.
ProCarManuals.com
Rail Applications
Install the o-ring and breather canister on the hand hole
cover.
Tighten the tube clamp.
Install the crankcase breather hose on the breather can-
ister.
Tighten the hose clamp.

Disassemble
Remove the lock nut and adjusting screw.
Remove the socket from the ball on the rocker lever shaft.
Place the ball in a vise as shown.

Wiggle the rocker lever until the ball swivels.
Use a mallet to tap the rocker lever until the ball comes out.
ProCarManuals.com

NOTE: The rocker lever must be disassembled to do this
inspection.
Amperage (Ampere Turns)
1200 D.C. or rectified A.C.
in the coil.
The lever must be replaced if there is a crack in any
location.
Demagnetize the lever.
Use solvent to clean the rocker lever.
Assemble
Install the adjusting screw and the lock nut in each lever.
Do not completely tighten the lock nut until the assembly
is installed on the engine.
CAUTION
Do not overstress the press fit.
Use a press to seat the new ball into the cavity in the rocker
lever.
The lip on the ball must be flush with the surface on the
rocker lever.
ProCarManuals.com
NOTE: Use an old push tube socket end to help hold and
align the ball for proper seating.
Install the new socket on the ball.

Rocker Lever Assembly (003-009)

Exploded View
ProCarManuals.com
1. Screw, Hexagon Head Cap 11. Seal, O-ring

2. Washer, Plain 12. Washer, Plain
3. Dowel, Ring 13. Screw, Rocker Lever Adjusting
4. Gasket, Rocker Lever Housing 14. Lever, Rocker
5. Housing, Rocker Lever 15. Screw, Twelve Point Cap
6. Rod, Push 16. shaft, Rocker Lever
7. Rod, Push 17. Plug, Expansion
8. Crosshead, Valve 18. Lever, Rocker
9. Nut Regular Hexagon Jam 19. Lever, Rocker
10. Screw, Twelve Point Cap 20. Socket, Rocker Lever
ProCarManuals.com
Clean
WARNING
personal injury.
Use solvent. Clean the shaft. Use compressed air to blow
through the oil drillings, to be sure that the nine oil holes
are not blocked.
The plug (1) in the main oil rifle of the rocker shaft must be
installed in the ring dowl end of the shaft (exhaust lever
end).
Use solvent to clean the parts.

Use compressed air to blow through the oil drillings, to be
sure that they are not blocked.
ProCarManuals.com
Inspect for Reuse

Remove the capscrews and hardened washers. Pull the
shaft out of the rocker levers.
Clean and inspect the parts for damage.
Inspect the shaft for damage or roughness.

Measure the O.D.
Rocker Arm Shaft O.D.

mm in
47.592 MIN 1.8737
47.634 MAX 1.8753
Inspect the socket for wear on both the injector and valve
sockets. Inspect the crosshead pad for wear.
NOTE: If there is damage that can be felt with the finger-
nail, the parts should be replaced.
Check the bushing wear. Measure the I.D. of the bushing.
Bushing Bore I.D.

mm in
47.66 MIN 1.876
47.73 MAX 1.879
NOTE: This specification applies to all rocker levers.
ProCarManuals.com
Lubricate the shaft with clean engine oil.

NOTE: The oil drillings in the shaft must be in alignment
with the oil drillings in the levers.
Slide the levers on the shaft in the sequence shown:
— Exhaust lever (1)
— Injector lever (2)
— Intake lever (3)
NOTE: The plug in the end of the shaft must be on the
same end as the exhaust rocker lever.
Lubricate threads, rocker sockets, and crosshead pads
with clean engine oil.
Install the washers and capscrews.
Disassemble
Remove the capscrews. Pull the shaft out. Tag the parts to
aid the future assembly procedure.
Rocker Lever Bushings (003-010)
Assemble
Use clean engine oil to lubricate the shaft.
CAUTION
The oil drillings in the shaft must be in alignment with
the oil drillings in the rocker levers.
The plug (4) in the main oil drilling must be nearest to the
exhaust lever (1). Slide the levers on the shaft in the se-
quence shown.
1. Exhaust lever
2. Injector lever
3. Intake lever

Remove
NOTE: Do not remove the bushing unless it is damaged or
worn.
Support the lever as shown (2). Use an arbor press and
rocker lever bushing mandrel, Part No. 3162458 (1), or
equivalent.
ProCarManuals.com
Remove the bushing.
Install
Use a 240 grit, or finer, emery cloth to remove any burrs
from the bore of the lever.
If cracks are suspected, use the magnetic particle inspec-
tion method. Refer to Procedure 003–008. The lever must
be replaced if it is worn.
Measure the rocker lever bore I.D.
Lever Bore I.D.

mm in
49.25 MIN 1.939
49.27 MAX 1.940
CAUTION
Refer to Service Tool Instructions for the proper use of
Tool No. 3162458. The bushings must be installed and
aligned in the bushing bore correctly. A loss of lubri-
cating oil to the shaft will occur if the bushings are
incorrectly installed.
Align the oil holes in the bushing (2) with the oil passages
in the lever.
Use an arbor press and a rocker lever bushing mandrel,
Part No. 3162458 (1), or equivalent. Install the bushing (2).
Rocker Lever Cover (003-011)
Rocker Lever Cover (003-011)

Clean
WARNING
personal injury.
Use solvent to clean the rocker lever covers.
Inspect for Reuse

Inspect the cover for cracks.
ProCarManuals.com
Rocker Lever Housing (003-013)

Clean
Remove the water transfer tube and o-rings.
WARNING
personal injury.
Rocker Lever Housing (003-013)
Inspect for Reuse

Inspect the parts for damage. If the ring dowel (4) is dam-
aged, it must be replaced. Use a blind hole puller con-
tained in light duty puller kit, Part No. 3375784, or equiva-
lent, to remove the dowel ring.
Use the dye penetrant method to inspect the housing for
cracks. If the housing is cracked, it must be replaced.
Assemble
Use vegetable oil to lubricate the o-rings (2).
Install the o-rings.
Install the water transfer tube (1).
ProCarManuals.com
Section 4 - Cam Followers/Tappets - Group 04 Page 4-a
Section 4 - Cam Followers/Tappets - Group 04

Section Contents
Page
Cam Follower Assembly .................................................................................................................................. 4-2
Assemble ..................................................................................................................................................... 4-5
Clean ........................................................................................................................................................... 4-3
Disassemble ................................................................................................................................................ 4-3
Exploded View .............................................................................................................................................. 4-2
Cam Follower Cover......................................................................................................................................... 4-6
Clean ........................................................................................................................................................... 4-6
Cam Followers/Tappets - General Information ................................................................................................ 4-1
Push Rods or Tubes......................................................................................................................................... 4-7
Clean ........................................................................................................................................................... 4-7
ProCarManuals.com
Cam Followers/Tappets - General Information
Section 4 - Cam Followers/Tappets - Group 04 Page 4-1
Cam Followers/Tappets - General

Information
CAUTION
The cam follower mounting capscrews are special 12-
point flange heads. Failure will result if standard
capscrews are used.
Pressurized engine oil is supplied to each cam follower
assembly through an oil cavity around the mounting
capscrews of each assembly.
The oil drilling in the shaft has a cup plug at both ends. This
means that either end of the shaft can be installed toward
the front of the engine. The ring dowel bores must not have
any burrs to install the assembly by hand. The cup plugs
in the end of the shaft keeps the flow of the pressurized oil
in the shaft instead of dumping the oil into the camshaft
cavity in the block. The cup plugs must be installed on the
ends of the shaft, outside the capscrew hole.
The QSK19 utilizes a one-piece cam follower cover with a
steel carrier paper gasket.
QSK19 cam followers are not rebuildable in the field, due

to the fit between the pin and lever. Liquid nitrogen is
ProCarManuals.com
required to shrink the pin sufficiently to slide through the

bores in the lever.
New cam follower and roller assemblies are coated with a
heavy preservative compound. They must be cleaned and
lubricated with engine oil before each assembly is installed
on the engine.
Rail Applications
The QSK19 Rail cam follower cover has been modified to
allow two lubricating oil scavenging tubes to be attached.
The tubes allow lubricating oil to be scavenged from the
cam follower cover to an oil manifold on the suction side of
the gear driven scavenge pump.
Cam Follower Assembly (004-001)
Page 4-2 Section 4 - Cam Followers/Tappets - Group 04

Exploded View
ProCarManuals.com
1. Ring, Retaining 9. Roller, Cam Follower

2. Lever, Cam Follower 10. Lockwire, Tpt Roller Pin
3. Lockwire, Tpt Roller Pin 11. Socket, Cam Follower
4. Pin, Cam Follower Roller 12. Shaft, Cam Follower
5. Roller, Cam Follower 13. Plug, Expansion
6. Socket, Cam Follower 14. Dowel, Ring
7. Lever, Cam Follower 15. Screw, Twelve Point Cap
8. Pin, Cam Follower Roller
Disassemble
Remove the 12 point capscrews.
Remove the retaining ring. Pull the shaft out.
Mark and tag the parts for future installation identification.
Clean
CAUTION
personal injury.
Use solvent, clean the cam follower assemblies.
ProCarManuals.com
Use compressed air to dry assemblies.
Use solvent, clean the cam followers.

Use compressed air to dry the cam followers and check the
oil drillings. Make sure the oil drillings are not plugged or
blocked.
Use solvent, clean the cam follower shaft.

Use compressed air to dry the shaft and check the nine (9)
oil drillings. Be sure all of the oil drillings are not plugged
or blocked.
Inspect for Reuse

Inspect the cam follower assembly for reuse.
The shaft must rotate easily. If resistance is apparent,
disassemble and check for burrs on the shaft.
Inspect the cam follower shaft for damage and roughness.

Check the cam follower shaft outer diameter.
Cam Follower Shaft O.D.

mm in
28.538 MIN 1.1235
28.575 MAX 1.125
ProCarManuals.com
Inspect the cam follower for reuse. The cam follower lever
assembly must be replaced if damaged.
Inspect the push rod socket for damage. If the socket is

damaged, the cam follower assembly must be replaced.
The roller must rotate easily. Check the clearance of the

roller.
Cam Follower Roller Clearance
Reference Point mm in
(1) 0.230 MIN 0.009
0.610 MAX 0.024
(2) 0.076 MIN 0.003

0.114 MAX 0.0045
NOTE: If the clearances do not meet specifications, the
cam follower lever assembly must be replaced.
Check the cam follower lever bore inner diameter.
Cam Follower Lever I.D.

mm in
28.611 MIN 1.1264
28.661 MAX 1.1284
NOTE: If the inner diameter does not meet specifications,
the cam follower lever assembly must be replaced.
ProCarManuals.com
Assemble
Use clean engine oil to lubricate the shaft and bores of the
levers.
Slide the levers on the shaft.
Install the parts as illustrated.
The shaft must rotate easily after assembly.

If resistance is apparent, disassemble and check for burrs
on the shaft.
Cam Follower Cover (004-002)
Cam Follower Cover (004-002)

General Information
The QSK19 has a one-piece, aluminum cam follower cover
with an oil fill.
NOTE: This is the only style of cam follower cover available.
Clean
CAUTION
personal injury.
Use solvent that will not harm aluminum to clean the cam
ProCarManuals.com
follower cover.
Inspect for Reuse

Check the cover for cracks or damage to the gasket sealing
surface.
Push Rods or Tubes (004-014)

General Information
The QSK19 uses push rods that are machined from solid
bar stock instead of tubing. The ball end and the socket are
machined on the rod.
It is a good service practice to mark the push rods for
location when removing them from the engine. The valve
and injector push rods are not interchangeable. The cam
follower assembly must be replaced if the push rod is worn
or damaged in the area where it contacts the socket.
NOTE: Replace both the rocker lever adjusting screw and
the push rod if the socket surface in the rod or on the
adjusting screw is damaged.
Clean
WARNING
personal injury.
Use solvent to clean the push rods.
ProCarManuals.com
Inspect for Reuse

Inspect the straightens of the push rod by rolling it on a level
surface. Replace the push rod if it is bent.
NOTE: Do not use or try to straighten a bent push rod.
Inspect both ends of the push rod for wear or damage.

NOTE: The cam follower assembly must be replaced if the
push rod is worn or damaged in the area where it contacts
the socket. Replace both the rocker lever adjusting screw
and the push rod if the socket surface in the push rod or
on the adjusting screw is worn or damaged.
Visually inspect the socket end of the push rod for uneven
wear or scratches.
If a worn socket is found, the mating adjusting screw in the
rocker lever must also be replaced.
When parallel scratches are found in the contact area, the
push rod must be replaced.
Visually inspect the ball end of the push rod.

The contact area must show a smooth seating pattern.
If the ball end of the push rod has parallel grooves and
scratches with a raised center, the push rod must be re-
placed.
NOTE: If a worn push rod is found, the mating cam follower
assembly must be replaced.
ProCarManuals.com
Section 5 - Fuel System - Group 05 Page 5-a
Section 5 - Fuel System - Group 05

Section Contents
Page
Fuel Pump........................................................................................................................................................ 5-6
Calibrate ...................................................................................................................................................... 5-7
Clean ........................................................................................................................................................... 5-6
Fuel Shutoff Valve (FSOV) ............................................................................................................................... 5-9
Clean ......................................................................................................................................................... 5-10
Install .......................................................................................................................................................... 5-11
Remove ........................................................................................................................................................ 5-9
Fuel System - General Information ................................................................................................................. 5-1
Service Tools ................................................................................................................................................... 5-4
Fuel System .................................................................................................................................................. 5-4
ProCarManuals.com
Fuel System - General Information
Section 5 - Fuel System - Group 05 Page 5-1

General Information
WARNING
sparks, arcing switches or equipment, pilot lights or
The QSK fuel system is used on the QSK19 engine.
WARNING
Tampering with the fuel pump can be a violation of law.
NOTE: Warranty repairs are not to be made to the fuel
pump unless the work is performed in a shop meeting all
requirements established by Cummins Engine Company,
Inc. to accurately calibrate, test and repair the fuel systems
on Cummins engines.
CAUTION
Tampering with the fuel pump can void the engine war-
ranty and lower the performance of the engine.
The performance of the engine is defined by the control
ProCarManuals.com
parts list (CPL) and the fuel pump code. The fuel pump
calibration must be within published specifications. Fuel
pump calibration is certified by several emissions agencies.
The QSK fuel system uses a PT type fuel pump to supply

a linear gear pump pressure from 60 psi at 600 rpm to 280
psi at 2100 rpm to the electronic fuel control valve assembly.
Page 5-2 Section 5 - Fuel System - Group 05
The QSK fuel pump throttle shaft is locked in the full closed
position.
There is no mechanical throttle on the QSK fuel pump.
The QSK fuel pump does not contain an AFC valve. The
pump only has an AFC cover plate.
ProCarManuals.com
The electronic fuel control valve assembly is located on the

fuel pump side of the engine.
The electronic fuel control valve assembly includes:
1. Timing Actuator
2. Fuel Shut off Valve
3. Rail Actuator
4. Ambient Air Pressure Sensor
5. Rail Pressure Sensor
6. Timing Pressure Sensor
7. Fuel Rail Supply Line Connector
8. Fuel Timing Supply Line Connector
9. Fuel Control Supply Line Connector
Rail Applications
NOTE: The lubricating oil scavenge pump (A) must be
removed prior to removing the fuel pump (B) to allow ac-
cess to the fuel pump mounting capscrews.
NOTE: The fuel pump (B) must be installed prior to in-
stalling the lubricating oil scavenge pump (A).
ProCarManuals.com
Service Tools
Service Tools
Fuel System

Fitting
Connects gauges when measuring various fuel pressures.
ST-435-7
ProCarManuals.com
Gauge
Used to measure the fuel pump pressure from 0 to 2758 kPa [0
to 400 psi]. Includes necessary hoses and hardware to attach to
3824877 a fuel pump.
Fuel Pump/Air Compressor Wrench

Used to reach nuts when removing or installing the fuel pump or
air compressor.
3376845
Digital Multimeter
Check resistance of fuel shut-off solenoid.
3377161
Lubricant DS-ES
Dielectric lithium grease used to lubricate the pins in the elec-
trical connectors.
3822934
QD Contact Cleaner
A nonpetroleum cleaner used to clean electrical connections.
3824510
Service Tools

Remote Starter Switch
Used to crank the engine to measure the cranking fuel pressure.
3376506
Optical Tachometer
Measure engine rpm.
3377462
Adapter S-Tool Kit

Used to hook QSK fuel pump to a fuel pump test stand.
3824875
3375698
ProCarManuals.com
Fuel Pump Test Stand

Used to check the calibration of the fuel pump.
3375698
Fuel Pump (005-016)
Fuel Pump (005-016)

Clean
WARNING
personal injury.
CAUTION
Put plastic cup plugs or tape on all of the openings. If
dirt enters the fuel pump, it can cause equipment dam-
age.
CAUTION
Use a cleaning solvent that will not harm aluminum.
Use a brush and solvent to clean the fuel pump exterior.
Inspect for Reuse

Clean the fuel pump and air compressor or accessory drive
mounting surfaces.
ProCarManuals.com
Inspect the mounting surfaces for damage.
Visually inspect the fuel pump body and front support for
cracks or other damage.
Visually inspect the fuel pump assembly for damaged
capscrews and damaged or loose fuel fittings.
Visually inspect the drive coupling lugs for excessive wear
or damage.
Fuel Pump (005-016)
Visually inspect the spider coupling for cracks or damage.
Calibrate
The Control Parts List (CPL), Bulletin No. 3379133, is a
listing of the basic parts and timing specifications.
Using the CPL number stamped on the engine dataplate
and this list, you can identify the necessary parts within an
engine to produce a specific performance.
ProCarManuals.com
When removing the fuel pump from the engine, check the
fuel pump dataplate (1), which is located on the top of the
fuel pump. The CPL number on the fuel pump dataplate
(2) must be the same as the CPL number on the engine
dataplate (4).
If the numbers do not match, do not install the fuel pump
again until the fuel pump calibration code (3) has been
changed to match the requirements of the engine dataplate
rating. If the fuel pump calibration is changed, the fuel
pump dataplate must be changed to indicate the new cali-
bration code and CPL number.
NOTE: Calibration of the fuel pump must be performed at
a Cummins Authorized Repair location.
NOTE: The throttle shaft is purposely locked in the closed

position. Rotation of the shaft is not necessary for pressure
checks.
Drain the fuel pump of diesel fuel as completely as possible
to avoid contaminating the test stand calibration fluid. Ro-
tation of the drive coupling in a counterclockwise direction
will aid in removing fluid held within the pump housing.
Fuel Pump (005-016)
Mount the fuel pump on the test stand. Refer to your par-
ticular test stand manufacturer’s operating and service
manual for pump installation instructions.
Set the test stand pump drive to 2100 rpm and purge any
air from the fuel pump and test stand.
NOTE: The fuel pump test stand fluid must be 32° to 38°
C [90° to 100° F] during the re-check procedure.
At 2100 rpm, set the flow volume to obtain 1157 pounds per
hour (Pph). Adjust the inlet restriction (see note below).
NOTE: The 178 mm (7 in Hg) inlet restriction value must
be used for all test stands where the vacuum gauge is
ProCarManuals.com
above the gear pump inner fitting. Use 127 mm (5 in Hg)

for vacuum gauges at the same level as the inlet fitting
Check point one

1. Adjust the test stand drive to obtain 2100 rpm.
2. Adjust the flow to obtain 1157 Pph.
3. Record the rpm, flow, and inlet restriction.
4. Read and record the pressure gauge value.
5. The gauge must read 250 to 300 psi.
Check point two
1. Reduce the test stand drive speed to 1300 rpm.

2. Adjust the flow volume to obtain 712 Pph.
4. Read and record the pressure gauge value.
5. The pressure valve must read 170 to 200 psi.
Fuel Shutoff Valve (FSOV) (005-043)
Check point three

1. Reduce the test stand drive speed to 600 rpm.
2. Adjust the flow to about 286 Pph.
4. Read and record the pressure gauge valve.
5. The pressure value must be 55 to 70 psi.
NOTE: The fuel pump can not be serviced in the field. If

the pressure values are not within the given tolerances, a
replacement pump must be obtained.

Remove
Remove the electronic control module (ECM). Refer to the
Troubleshooting and Repair Manual, Bulletin No. 3666098.
ProCarManuals.com
WARNING
personal injury.
Use solvent to clean the fuel shutoff valve and surrounding
area.
Use a 3/8 in wrench to remove the nut holding the electrical

connection of the fuel shutoff valve coil.
Remove the connection.

Remove the coil housing and the fuel shield.
Discard the o-ring.
Remove the spring washer, valve disc, actuator disc, and
actuator spacer from the valve housing.
Discard the o-ring.
Clean
Use mineral spirits to clean all of the parts except the coil
assembly.
NOTE: Do not get solvent on the coil. Clean the coil with
a dry cloth. Use a 200 grit emery cloth and a flat surface
to polish the coil surface.
ProCarManuals.com
Use a wire brush to clean any corrosion from the coil

terminal.
Inspect for Reuse

Visually check the valve disc, valve seat, and actuator disc
for dirt, metal parts, bonding separation, corrosion, cracks,
or wear. Replace if necessary.
Check the coil assembly with a multimeter.

Replace the coil if it does not have 28 to 32 Ω of resistance.
NOTE: If the coil assembly shows 0 ohms, there is an
electrical short in the coil.
Tighten the nut that holds the electrical connection post on

the fuel shutoff valve coil.
ProCarManuals.com
Install
Assemble the shutoff valve as shown. Install these parts as
follows.
Install a new o-ring (6) between the spacer (7) and the
electronic control valve body (8).
Install the spacer (7) o-ring groove toward the coil.
Install the actuator disc (5) with the cup side toward the coil.
Install the spring washer (3) with the cup side toward the
coil.
Align the actuator disc (5), spacer (7), and valve disc (4) on
the electronic control valve body (8).
Install a new o-ring (6).
Put the spring washer (3) on the valve disc (4), with the
cavity side positioned upward.
NOTE: The coil must be orientated with the electrical con-
nection post on the bottom.
NOTE: Make sure the shutoff valve coil is the correct volt-
age (24 volts). The coil voltage and part number are cast
into the terminal connection end of the coil.
Install the fuel shield (2) and coil (1) on the front cover (8).
Install a new o-ring and tighten the capscrews.
Install the electrical connection on the fuel shutoff valve.

Install the nut on the threaded post of the coil.
Use two 3/8 in wrenches hold the post of the nut firmly while
tightening the connection nut.
ProCarManuals.com
Install the ECM. Refer to the Troubleshooting and Repair

Manual, Bulletin No. 3666098.
Section 6 - Injectors and Fuel Lines - Group 06 Page 6-a
Section 6 - Injectors and Fuel Lines - Group 06

Section Contents
Page
Fuel Filter Head ............................................................................................................................................... 6-2
Install ........................................................................................................................................................... 6-2
Remove ........................................................................................................................................................ 6-2
Fuel Manifold (Supply)..................................................................................................................................... 6-3
Clean ........................................................................................................................................................... 6-3
Fuel Supply Lines ............................................................................................................................................ 6-4
Clean ........................................................................................................................................................... 6-4
Fuel Control Supply Line ....................................................................................................................... 6-5
Fuel Inlet Line ....................................................................................................................................... 6-6
Fuel Rail Supply Line ............................................................................................................................ 6-5
Fuel Tank-To-Fuel Filter ......................................................................................................................... 6-5
Fuel Timing and Supply Line................................................................................................................. 6-5
Injector ............................................................................................................................................................. 6-6
Clean ........................................................................................................................................................... 6-6
Injectors and Fuel Lines - General Information .............................................................................................. 6-1
ProCarManuals.com
Injectors and Fuel Lines - General Information
Section 6 - Injectors and Fuel Lines - Group 06 Page 6-1
Injectors and Fuel Lines - General

Information
General Information
The QSK19 uses a QSK fuel system that requires a split
fuel manifold and three fuel circuits. The three circuits are
rail (1), timing (2), and drain (3).
WARNING
sparks, arcing switches or equipment, pilot lights, or
Fuel is delivered to the fuel blocks (4) at the front and rear
of the engine from the electronic control valve assembly.
ProCarManuals.com
The QSK19 uses face seal o-ring fittings, except the fuel
filter inlet and the fuel drain connection that are 37 degree
flare fittings.
1. Tube nut
2. Tube flare (flat)
3. O-ring
4. Fitting
CAUTION
If LubriplateT is not used, the o-ring can fall out or get
pinched during assembly and cause a fuel leak.
Hold the o-rings in position during assembly using Lubri-
plateT 105, or equivalent.
Fuel Filter Head (006-017)
Page 6-2 Section 6 - Injectors and Fuel Lines - Group 06
Rail Applications
The ten-micron fuel filters/water separators (A) are remote
mounted on the lubricating oil pan on the front side of the
engine.
Fuel Filter Head (006-017)

Remove
Disconnect the fuel line from the fuel filter head.
ProCarManuals.com
Remove the two mounting capscrews.

Remove the fuel filter head.
Install
Install the fuel filter head.
Install the two mounting capscrews.
Fuel Manifold (Supply) (006-022)
Connect the fuel line to the fuel filter head.

Clean
Remove the four fuel connection block capscrews.
Remove the fuel connection block.
ProCarManuals.com
NOTE: The illustration shows the fuel manifold turned up-

side down. The small hole is on the bottom of the fuel
manifold.
Remove the two 3/8 in plugs (2) and four 1/2 in plugs at the
ends of the manifold.
Discard the o-ring if damaged or enlarged.
Use solvent to clean the manifold.

Use compressed air to clean all of the drillings.
Be sure all the drillings are clean and open.
Fuel Supply Lines (006-024)
Inspect for Reuse

Check the manifold for cracks in the fuel passages.
The manifold must be replaced if damaged.
Use clean engine oil to lubricate the o-rings.

Install the 3/8 in (2) and 1/2 in plugs (1).
Torque Value:
Plug (1): 20 N•m [180 in-lb]
Torque Value:
Plug (2): 7 N•m [60 in-lb]
ProCarManuals.com
Use LubriplateT to secure the o-rings in position.

Install the fuel connection block and the four new o-rings.

Clean
WARNING
personal injury.
Remove and discard the ferrule seals.
Use solvent to flush the tubing and fuel block connectors.
Inspect for Reuse

Fuel Tank-To-Fuel Filter
Visually inspect the inside of the hose.
• The inner lining of the hose can separate from the
center hose section.
• A separation of flap can cause a restriction in the
fuel flow.
Visually inspect for any pinches in the hose that would
obstruct the flow.
Be sure the hose does not have pinches or loops that would
obstruct the flow.
Fuel Rail Supply Line

Fuel Timing and Supply Line
Use compressed air. Flush the lines and remove any loose
dirt particles.
ProCarManuals.com
Visually inspect the fuel line for cracks that can cause a
loss of pressure.
Visually inspect the fuel line for sharp bends that can cause
a restriction in pressure.
Fuel Control Supply Line

Visually inspect the hose for pinched areas that prevent the
proper flow, or frayed mesh. The hose must be replaced if
damaged.
Injector (006-026)
Use compressed air. Flush the lines and remove any loose
dirt particles.
Fuel Inlet Line

Visually inspect the inside of the hose.
• The inner lining of the hose can separate from the
center hose section.
• A separation of flap can cause a restriction in the
fuel flow.
Visually inspect for bends in the line that can restrict the
ProCarManuals.com
fuel flow.
Injector (006-026)
Clean
Use a lint free cloth to clean the exterior of the injector.
Inspect for Reuse

Remove the sealing ring (1) and note the cylinder location.
NOTE: Sealing rings are available in different thickness
sizes to adjust the injector protrusion.
Injector (006-026)
NOTE: The four new o-rings must be installed and oriented

correctly on the injector. Identify the o-rings to install them
in the correct grooves.
Remove the o-rings (2, 3, 4, and 5).
Carefully check the area where the sealing ring touches the
injector.
Visually inspect the o-ring grooves for damage.
Visually inspect the injector body and cup retainer for cracks
or other damage.
Visually inspect the injector links for damage, excessive
wear, and pitting or scoring on the ball ends.
NOTE: If the link is damaged or pitting/scoring can be seen
or felt, the link must be replaced.
O-ring (2) is brown and is smaller in diameter than the other

three.
O-ring (3) is black.
O-ring (4) is brown and is larger in diameter than (2), but
has a smaller cross section than o-ring (5).
O-ring (5) is brown and is the largest in diameter and cross
ProCarManuals.com
section.
NOTE: Do not lubricate the o-rings until the injector is

ready for installation in the cylinder head.
Install four new o-rings on the injector. Do not twist the
o-rings.
Install the proper size sealing ring (1).
Filter Screen
NOTE: Use solvent when cleaning the filters. The screens
must be thoroughly dry prior to installation.
Check the rail (6) and timing (7) filter screens for debris,
tears, or punctures. Replace the filter screens if damaged
or dirty.
Injector (006-026)
Check the rail (6) and timing (7) filter for proper installation.
Screens must be securely snapped into correct position.
Use a small screwdriver to remove the filter screen by

gently prying up on the connector clip.
ProCarManuals.com
Wrap the filter screen around the inlet groove.
Apply pressure on the filter screen connector clip.

NOTE: A properly secured connector will create a single,
snapping sound.
Section 7 - Lubricating Oil System - Group 07 Page 7-a
Section 7 - Lubricating Oil System - Group 07

Section Contents
Page
Lubricating Oil Cooler...................................................................................................................................... 7-3
Clean ........................................................................................................................................................... 7-4
Exploded View .............................................................................................................................................. 7-3
Lubricating Oil Filter Head .............................................................................................................................. 7-5
Assemble .................................................................................................................................................... 7-10
Clean ........................................................................................................................................................... 7-9
Disassemble ................................................................................................................................................ 7-8
Exploded View .............................................................................................................................................. 7-6
Lubricating Oil Filter Head Adapter............................................................................................................... 7-13
Clean ......................................................................................................................................................... 7-13
Lubricating Oil Filter Head (Remote-Mounted).............................................................................................. 7-11
Assemble ................................................................................................................................................... 7-12
Clean ......................................................................................................................................................... 7-12
Disassemble ............................................................................................................................................... 7-11
ProCarManuals.com

Lubricating Oil Pan ........................................................................................................................................ 7-15
Oil Pan Capacity ................................................................................................................................. 7-15
Lubricating Oil Pan Adapter........................................................................................................................... 7-16
Clean ......................................................................................................................................................... 7-16
Lubricating Oil Pump ..................................................................................................................................... 7-17
Assemble ................................................................................................................................................... 7-22
Clean ......................................................................................................................................................... 7-19
Disassemble ............................................................................................................................................... 7-19
Exploded View ............................................................................................................................................ 7-18
Lubricating Oil System - General Information................................................................................................. 7-1
Oil Transfer Connection................................................................................................................................. 7-23
Assemble ................................................................................................................................................... 7-24
Clean ......................................................................................................................................................... 7-23
Disassemble ............................................................................................................................................... 7-23
Service Tools ................................................................................................................................................... 7-2
Lubricating Oil System .................................................................................................................................. 7-2
Lubricating Oil System - General Information
Section 7 - Lubricating Oil System - Group 07 Page 7-1
Lubricating Oil System - General

Information
General Information
WARNING
Some state and federal agencies in the United States of
America have determined that used engine oil can be
with used engine oil. Always use the proper procedure
to dispose of the used oil.
NOTE: The use of low viscosity oil, such as 10W or 10W-30,

can be used to aid in starting the engine and in providing
sufficient oil flow at ambient temperatures below -5°C
[23°F], but continuous use of low viscosity oil can decrease
engine life due to wear.
ProCarManuals.com
A used oil analysis can help diagnose internal damage and

determine if it was caused by one of the following:
• Intake air filter malfunction
• Coolant leaks
• Oil diluted with fuel
• Metal particles causing wear
NOTE: Do not disassemble an engine for repair based only
on the results of an oil analysis. Inspect the oil filter, also.
If the filter shows evidence of internal damage, find the
source of the problem and repair the damage. Refer to the
appropriate section(s) based on the oil filter inspection.
Service Tools
Page 7-2 Section 7 - Lubricating Oil System - Group 07
Service Tools

Oil Filter Wrench
Remove spin-on oil filter.
3375049
ProCarManuals.com
Pressure Regulator Removal Tool

Remove retaining ring from lubricating oil pump regulator (on
engine).
3375055
Valve Spring Tester

Measure spring force at a given spring height.
3375182
Filter Cutter
Open spin-on full-flow filter for inspection.
3376579
Fluorescent Tracer
Add to oil. Use with black light to find oil leaks.
3376891
Lube Pump Boring Tool

Used to bore replacement bushings in the lube oil pump.
3375206
Lubricating Oil Cooler (007-003)

Exploded View
ProCarManuals.com
1. Screw, Hexagon Head Cap

2. Washer, Lock
3. Adirondack
4. Washer, Plain
5. Seal, O-ring
6. Screw, Twelve Point Cap
7. Plug, Threaded
8. Screw, Captive Washer Cap
11. Washer, Plain
14. Housing, Oil Cooler
15. Core, Cooler
16. Cover, Lube Oil Cooler
17. Gasket, Oil Cooler Core
18. Gasket, Tor Converter Oil Cooler
19. Gasket, Lube Oil Cir Hsg
20. Seal, O-ring
21. Plug, Threaded
22. Seal, O-ring
23. Plug, Threaded
General Information
All QSK19 engine oil cooler housings are cast iron.
Clean
WARNING
personal injury.
Use a solvent that will not harm copper to clean the oil
ProCarManuals.com
cooler elements.
NOTE: Replace the elements if any debris is found or the
engine has had a debris causing failure.
Use solvent and clean the oil cooler housing and cover.
Inspect for Reuse

Pressure test the elements.
Check for leaks.
Torque Value: 415 kPa [60 psi]
Check the cover and housing for cracks. If leaks are sus-
pected, use the dye penetrant method to locate them.
Check the cover and housing for corrosion.
Lubricating Oil Filter Head (007-015)

General Information
The oil filter head contains two spring loaded plungers. One plunger controls the oil pressure for the piston cooling
nozzles. The second spring plunger will bypass oil if a filter element becomes plugged or clogged.
When installing a new filter element, always check to be sure there is no interference between the filter head adapter
and the element.
The oil filter remote option has a transfer connection and a remote filter head. The transfer connection is attached to
the block in the same manner as the standard filter head. The transfer connection also houses the pressure regulator
plunger for the piston cooling nozzles. The remote filter head houses the pressure regulator plunger for the filter bypass.
NOTE: The transfer connection gasket is the same as the filter head gasket, but the tab on the end of the gasket must
be removed.
ProCarManuals.com
Exploded View
ProCarManuals.com

2. Gasket, Lube Oil Fill Cover
3. Seal, O-ring
4. Elbow, Male Union
5. Seal, O-ring
6. Screw, Hexagon Head Cap
7. Pin, Roll
8. Plug, Threaded
9. Washer, Plain
10. Seal, O-ring
11. Plunger, Filter Head
12. Seal, O-ring
13. Plug, Threaded
14. Head, Lube Oil Filter
15. Adapter, Filter Head
16. Seal, O-ring
17. Seal, O-ring
18. Spring, Valve
19. Elbow, Plain Union
20. Valve, Check
21. Seal, O-ring
22. Plug, Threaded
23. Seal, O-ring
24. Hose, Flexible
25. Element, Lube Oil Filter
ProCarManuals.com
Disassemble
WARNING
The threaded plug is under pressure, wear goggles to
prevent personal injury.
Remove the bypass regulator plunger and related parts.
2. Regulator plug
3. O-ring
4. Bypass valve spring
5. Bypass valve regulator plunger
Discard the o-ring.
WARNING
The threaded plug is under pressure, wear goggles to
prevent personal injury.
Remove the piston cooling nozzle plunger and parts.
8. Pressure regulator plug
9. O-ring
10. Piston cooling valve spring
11. Piston cooling valve plunger
ProCarManuals.com
Discard the o-ring.
Remove the remaining straight threaded o-ring plugs.
LF3000 Filter Head Adapter

Remove the filter head adapter.
Remove and discard the filter head adapter o-rings.

Use a 1-1/2 inch socket to remove the adapters.
Clean
WARNING
personal injury.
Use a gasket scraper to remove the two mounting gaskets.
ProCarManuals.com
Use solvent to clean the lubricating oil filter head.

Inspect for Reuse

Check the lubricating oil filter head for cracks or other
damage.
Check the visible portion of the valve plungers for signs of
scoring or other damage.
If any of the plungers are damaged, the filter head must be
rebuilt.
Check the bypass plunger spring.
Bypass Plunger Spring

mm in
Free Length 88.98 MIN 3.500
Working Height (6) 50.80 MAX 2.000
Use a valve spring tester, Part No. 3375182, or equivalent
to measure the spring force (7) and the working height (6).
Spring Force (7)

N•m ft-lb
26 MIN 19.3
29 MAX 21.3
Check the piston cooling nozzle spring.
Piston Cooling Nozzle Spring

mm in
Free Length 88.98 MIN 3.500
Use a valve spring tester, Part No. 3375182, or equivalent
to measure the spring force (7) and the working height (6).
Spring Force (7)

N•m ft-lb
26 MIN 19.3
29 MAX 21.3
Assemble
Use engine oil to lubricate the bypass regulator plunger
and related parts.
Install the new o-ring (3) on the regulator plug (2).
Install the parts.
5. Bypass valve regulator plunger
4. Bypass valve spring
ProCarManuals.com
2. Regulator plug with o-ring (3)

Tighten the regulator plug.
Use clean engine oil and lubricate the piston cooling nozzle
plunger and related parts.
Install a new o-ring (9) on the piston cooling nozzle plunger
plug (8).
Install the parts.
11. Piston cooling valve plunger
10. Piston cooling valve spring
8. Pressure regulator plug with o-ring (9)
Tighten the piston cooling nozzle plunger plug.
Tighten the straight threaded o-ringed plugs.

Torque Value:
1-5/16 61 N•m [45 ft-lb]
9/16 14 N•m [10 ft-lb]
Lubricating Oil Filter Head (Remote-Mounted) (007-017)

Lubricate the o-ring (1) and install in the filter head before
the adapter.
Lubricate the o-rings (2 and 3) and install in the adapter.
NOTE: When installing the filter head adapter, use a lo-
cating pin to properly align the filter head adapter to the
filter head.
Install the adapter and four capscrews.

Apply Locktite™ 609, or equivalent, to the threads of the
adaptor.
Install the adapter into the filter head.
Use a 1-1/2 inch socket to tighten the adapters.
ProCarManuals.com
Lubricating Oil Filter Head

(Remote-Mounted) (007-017)
Disassemble
Remove the straight thread o-ring plug (1).
CAUTION
The threaded plug (3) is under spring pressure, wear
goggles to prevent personal injury.
Remove the straight thread o-ring plug (3), bypass plunger
(1), and spring (2).
Clean
WARNING
personal injury.
CAUTION
All solvent must be removed from the filter head or
engine damage could result.
Use solvent and clean all of the parts.
Inspect for Reuse

Inspect the filter head for crack.
If any cracks are found replace the filter head.
ProCarManuals.com
Check the bypass plunger spring.

mm in
Free Length 88.98 MAX 3.500
Use a valve spring tester Part No. 3375182, or equivalent.
Measure the spring force (7) and the working height (6).
Spring Force (7)

N•m ft-lb
26 MIN 19.3
29 MAX 21.3
Assemble
Use clean engine oil to lubricate the parts.
Install the new o-rings on the straight threaded plugs.
Install the plunger and spring.
Install the straight threaded o-ring plugs.
Tighten the plugs.
Torque Value:
9/16 Plug 14 N•m [10 ft-lb]
1-3/16 Plug 54 N•m [40 ft-lb]
1-7/8 Plug 95 N•m [70 ft-lb]
Lubricating Oil Filter Head Adapter (007-018)
Lubricating Oil Filter Head Adapter

(007-018)
General Information
When installing a new filter element, always check to be
sure there is no interference between the filter head adapter
and the filter element.
Clean
LF3000
WARNING
personal injury.
ProCarManuals.com
Use solvent to clean the lubrication oil filter head adapter.

LF670
WARNING
personal injury.
Inspect for Reuse

LF3000
Visually inspect the adapter for cracks or other damage.
Replace if any damage is found.
Lubricating Oil Filter Head Adapter (007-018)
LF670
Check the threads on the adaptors for damage.
Replace if any damage is found.
ProCarManuals.com
Lubricating Oil Pan (007-025)

General Information
Oil pan sumps are available in various capacities. Compare the part number to the chart below to find the correct high
and low capacities. When the rear gear train option is specified, add 7.6 liters [2 U.S. gallons] to the sump capacity
listed in the table below.
Service dipsticks are available in two types. The first is the locking type. The second is the bottle stopper type that does
not lock. When converting from one style to the other, change both the dipstick and the oil gauge tube.
NOTE: Service dipsticks are supplied by length. The dipsticks do not have the high and low marks indicated. Do not
calibrate the dipstick until the engine is installed in the application that its to be used.
Oil Pan Capacity The following tabulation gives the low and high STATIC (engine not operating) oil level for the pan
installed. Use this information when calibrating the oil gauge (dipstick).
NOTE: Only the part number of the oil pan (sump) is given. The part number of the oil pan adapter does not change
the engine oil capacity.
Oil Pan Capacities

liters U.S.gal
Shallow full length 49 MIN 13
PN 3086097 61 MAX 16
Long (1/3) deep 49 MIN 13

ProCarManuals.com
PN 3086096 61 MAX 16
Short (1/3) deep 49 MIN 13

PN 3331695 61 MAX 16
Marine, deep rear 64 MIN 17

PN 3096460 72 MAX 19
Power Generator 102 MIN 27

PN 3331568 114 MAX 30
NOTE: Total system capacity is the summation of the oil pan capacity at the high mark on the dipstick, and the two
LF3000 combination full flow/bypass oil filters. On engines with the rear gear train option, add 7.6 L (2 U.S. gal) to both
the low and high oil pan capacity listed in the table above.
Lubricating Oil Pan Adapter (007-027)
Lubricating Oil Pan Adapter (007-027)

Clean
WARNING
Always read and follow the solvent manufacturers safety
precautions to avoid severe personal injury or death.
Remove any hand hole covers not previously removed.
Use a solvent that will not harm aluminum clean the oil pan
adapter and hand hole covers.
WARNING
personal injury.
Use solvent to clean the suction tube.
ProCarManuals.com
Inspect for Reuse

Visually inspect the oil pan adapter for cracks or other
damage.
If cracks are suspected, use the dye penetrant method.
Check the threaded holes for damage.
Inspect the suction tube for cracks or other damage.

Lubricating Oil Pump (007-031)

General Information
The QSK19 lubricating oil pump uses a retaining ring to
secure the pressure regulator assembly.
Use pressure regulator removal tool, Part No. 3375055, to
service the pressure regulator assembly when the lube oil
pump is installed in the engine.
ProCarManuals.com
Exploded View
ProCarManuals.com
1. Seal, O-ring
2. Seal, Rectangular Ring
4. Screw. Hexagon Head Cap
5. Washer, Lock
7. Gasket, Lubricating Oil Pump
8. Dowel, Pin
9. Dowel, Diamond
10. Gear, Lubricating Oil Pump
11. Bushing
12. Body Lubricating Oil Pump
13. Gear, Lubricating Oil Pump
14. Shaft, Lubricating Oil Pump Drive
15. Shaft, Idler
16. Ring, Retaining
17. Plug, Retainer
18. Spring, Compression
19. Plunger, Pressure Regulator
20. Cover, Lubricating Oil Pump
Disassemble
Remove the cover from the housing.
Use a mallet to tap on the dowel to separate the cover from
the housing.
Lift the idler gear and the shaft from the housing.
Support the housing.

Use an arbor press to remove the drive gear, push the shaft
through the gear.
ProCarManuals.com
WARNING
To prevent personal injury, it is imperative to follow the
instructions given below. Wear safety goggles to pre-
vent personal injury.
Use an arbor press, and a mandrel (1) to hold the retainer
(4) in position.
Remove the retaining ring (3).
Slowly raise the arbor press and allow the spring tension
to be relieved.
Remove the retainer, the pressure spring, and the pressure
regulator plunger.
Check the parts for any damage.
Clean
Use solvent to clean and flush the oil pump.
Inspect for Reuse

WARNING
Inspect the lubricating oil pump for reuse, by rotating the
drive gear slowly and checking the pump gears for dam-
age.
NOTE: If any of the oil pump parts are damaged, it must
be rebuilt or replaced.
Measure the oil pump end clearance.
Oil Pump End Clearance

mm in
0.1016 MIN 0.004
0.2540 MAX 0.010
ProCarManuals.com
Measure the I.D.
Bushing I.D.
mm in
22.263 MIN 0.8765
22.324 MAX 0.8785
NOTE: The bushings are bored in position. Lubricating
pump bushing boring tool, Part No. 3375206 must be used
to machine the bushings.
Measure the pressure regulator spring free length.
Pressure Regulator Spring Free Length

mm in
95 NOMINAL 3.75
Use a valve spring tester, Part No. 3375182, or equivalent.
Measure the spring force (7) at the working height (6).
Spring Force @ 63.88 mm [2.5 in] Working Height

N lb
322 MIN 72
344 MAX 77
Check the gears for damage.

Measure the O.D.
Shaft O.D.
mm in
22.212 MIN 0.8745
22.225 MAX 0.8750
Only disassemble when the gear or the shaft must be

replaced.
Support the gear, use an arbor press to push the shaft
through the gear.
ProCarManuals.com
Measure the I.D. of the gear.
Gear I.D.
mm in
22.169 MIN 0.8728
22.195 MAX 0.8738
Measure the O.D. of the shaft.
Shaft O.D.
mm in
22.212 MIN 0.8745
22.225 MAX 0.8750
NOTE: Any parts not with in the given tolerances must be
replaced.
Use clean engine oil to lubricate the shaft and the I.D. of
the gear.
Use an arbor press to install the gear.
Gear Location on Shaft

mm in
Idler 26.162 MIN 1.03
26.67 MAX 1.051
Drive 26.162 MIN 1.03

26.416 MAX 1.040
Assemble
Use clean engine oil to lubricate the regulator plunger (5)
and the bore.
Install the regulator plunger, spring, and retainer (4).
Use and arbor press, and mandrel (1), to compress the
spring, and put the retainer in position.
Use clean engine oil and lubricate the shaft and gear inner
diameter
Install the gear and the shaft assembly (6), into the hous-
ing.
Use an arbor press, support the oil pump shaft. Place the
gear over the shaft, and using a mandrel press the gear
onto the shaft (7), until the gear is even with the shaft.
NOTE: The part number of the drive gear must be posi-
ProCarManuals.com
tioned up.
Use clean engine oil and lubricate the bushings in the

housing cover.
Install the shaft into the housing.
Install the gasket.
Use a mallet. Install the cover over the dowels.
Install the four capscrews.
Torque the capscrews.
Rotate the assembly.

Measure the end play.
End Play
mm in
0.1016 MIN 0.004
0.254 MAX 0.010
Oil Transfer Connection (007-061)

Disassemble
Remove the straight thread o-ring plugs (1), (2), and (3).
Discard the o-rings
Remove the vent tube (1).

CAUTION
The threaded plug (2) is under spring pressure.
Remove the piston cooling nozzle plunger (3) and spring
(4).
ProCarManuals.com
Clean
WARNING
personal injury.
Inspect for Reuse

Inspect the parts for wear or damage.
Check the piston cooling nozzle spring.

mm in
Free Length 88.98 MAX 3.500
Use a valve spring tester, Part No. 3375182, or equivelent
to measure the spring force and the working height
Spring Force (7)

N•m ft-lb
26 MIN 19.3
29 MAX 21.3
Assemble
Use clean engine oil to lubricate the parts.
Install the new o-rings on the plugs.
Install the plunger, spring and vent tube.
Install and tighten the straight threaded o-ring plugs.
Torque Value:
ProCarManuals.com
9/16 Plug 14 N•m [10 ft-lb]

1 3/16 Plug 54 N•m [40 ft-lb]
1 7/8 Plug 95 N•m [70 ft-lb]
Section 8 - Cooling System - Group 08 Page 8-a
Section 8 - Cooling System - Group 08

Section Contents
Page
Coolant Thermostat ......................................................................................................................................... 8-4
Install ........................................................................................................................................................... 8-6
Conventional Aftercooling...................................................................................................................... 8-6
Low Temperature Aftercooling ............................................................................................................... 8-7
Remove ........................................................................................................................................................ 8-4
Test .............................................................................................................................................................. 8-8
Engine Thermostats .............................................................................................................................. 8-8
Low Temperature Aftercooling Thermostat ............................................................................................. 8-9
Coolant Thermostat Housing Support........................................................................................................... 8-10
LTA Cooling System ............................................................................................................................. 8-10
Thermostat .......................................................................................................................................... 8-10
Thermostat Seal .................................................................................................................................. 8-10
Thermostat Support ............................................................................................................................. 8-10
Cooling System - General Information ............................................................................................................ 8-1
Fan, Cooling................................................................................................................................................... 8-18
Fan Drive Idler Arm Assembly ....................................................................................................................... 8-11
ProCarManuals.com
Assemble ................................................................................................................................................... 8-12

Clean .......................................................................................................................................................... 8-11
Disassemble ............................................................................................................................................... 8-11
Fan Drive Idler Pulley Assembly.................................................................................................................... 8-12
Clean ......................................................................................................................................................... 8-12
Fan Hub, Belt Driven...................................................................................................................................... 8-14
Assemble ................................................................................................................................................... 8-16
Clean ......................................................................................................................................................... 8-15
Service Tools ................................................................................................................................................... 8-3
Cooling System ............................................................................................................................................. 8-3
Torque Converter Cooler ............................................................................................................................... 8-26
Assemble ................................................................................................................................................... 8-27
Clean ......................................................................................................................................................... 8-28
Disassemble ............................................................................................................................................... 8-28
Exploded View ............................................................................................................................................ 8-26
Water Pump.................................................................................................................................................... 8-19
Assemble ................................................................................................................................................... 8-22
Clean ......................................................................................................................................................... 8-21
Disassemble ............................................................................................................................................... 8-19
Inspect ....................................................................................................................................................... 8-21
Water Pump Bearings .................................................................................................................................... 8-28
Install ......................................................................................................................................................... 8-29
Measure ..................................................................................................................................................... 8-28
Remove ...................................................................................................................................................... 8-28
Cooling System - General Information
Section 8 - Cooling System - Group 08 Page 8-1

General Information
The primary function of the cooling system is to remove
heat energy, created by the combustion process, from the
engine. The excess heat energy that is not removed by the
cooling system is carried away by exhaust gases and ra-
diation into the atmosphere.
The QSK19 requires a radiator cap with a minimum pres-
sure rating of 48 kPa [7 psi]. This provides a positive coolant
head pressure at the water pump inlet.
The accompanying chart illustrates the Conventional After-

cooling coolant flow through the engine.
A. Water Pump
B. Base Engine
C. Thermostat, Engine
D. Radiator, Engine
E. Oil Cooler
F. Aftercooler
ProCarManuals.com
The accompanying chart illustrates the Low Temperature

Aftercooling (LTA) coolant flow through the engine.
A. Water Pump
B. Base Engine
C. Thermostat, Engine
D. Radiator, Engine
E. Low Temperature Aftercooling Thermostat
F. Low Temperature Aftercooling Radiator
G. Aftercooler
Page 8-2 Section 8 - Cooling System - Group 08
The following publications, available through Cummins Dis-

tributors or Cummins Dealers, provide cooling system in-
stallation recommendations and specifications approved
by Cummins Engine Company, Inc.
• Automotive Installation Recommendations (Cooling
System), Bulletin No. 3382413.
• Construction, Mining, Logging, and Agriculture In-
stallation Recommendations (Cooling System), Bul-
letin No. 3382171.
• Data Sheets for Construction, Mining, Logging, and
Agriculture, Bulletin No. 3381194; for Generator Drive
and Generator Set, Bulletin No. 3381174; for Auto-
motive, Bulletin No. 3381237.
• Operation of Diesel Engines in Cold Climates, Bul-
letin No. 3379009.
• Generator Drive and Generator Set Installation Rec-
ommendations (Cooling System), Bulletin No.
3382395.
• Coolant Requirements and Maintenance, Bulletin
No. 3666132.
NOTE: Refer to Section L for literature ordering information.
ProCarManuals.com
Service Tools
Service Tools
Cooling System

Gear Puller
Used to remove the drive pulleys and impellers.
ST-647
ProCarManuals.com

Used to install drive pulleys.
3376326
Coupling Puller
Used to remove accessory drive coupling.
3376663

3824760
Pipe Sealant
Use when installing pipe plugs or cup plugs on the engine in order
to prevent leaks.
3375066
Dowel Pin Extractor

Used to pull dowel pins.
ST-1134
Coolant Thermostat (008-013)

Remove
WARNING
Some coolants are poisonous. Keep away from children
and animals. Save for reuse or dispose of in accordance
with local authorities.
NOTE: If the engine is equipped with an air compressor,
remove the air compressor coolant return tube.
Remove bypass tube clip (9).
Remove the eight long capscrews.

Remove the thermostat housing.
ProCarManuals.com
Remove the thermostats (9).

Remove the seals (10).

WARNING
Allow the engine to cool before draining to avoid burns
from hot liquid.
WARNING
Some coolants are poisonous. Keep away from children
and animals. Save for reuse or dispose of in accordance
with local authorities.
Remove the aftercooler return tube clip.
Loosen both hose clamps (2).
Remove the aftercooler coolant return tube (1).
Remove the bypass tube clip (9).

ProCarManuals.com
Remove the nine long capscrews.

Remove the thermostat housing.
Remove both of the engine thermostats (1).

Remove the Low Temperature Aftercooling thermostat (2).
Remove the seals.
Install
Engine Thermostats
CAUTION
The seal must be installed with the part number point-
ing up.
Use a mallet and thermostat seal driver, Part No. 3375411,
or equivalent. Install the thermostat seal no more than 0.51
mm [0.020 in] below the top of the cast edge.
Install the thermostat seals.
Install the thermostat by pushing on the outer rim.

ProCarManuals.com
Install a new gasket.

Install the thermostat housing and capscrews.
Use vegetable oil to lubricate the o-ring on the bypass tube.

Torque Value:
Torque Value:

CAUTION
The seal must be installed with the part number point-
ing up.
Use a mallet and thermostat seal driver, Part No. 3375411,
or equivalent. Install the thermostat seal no more than 0.51
mm [0.020 in] below the top of the cast edge.
Install the thermostat seals.
Install the thermostat by pushing on the outer rim.

ProCarManuals.com

Install the thermostat housing and capscrews.
Use vegetable oil to lubricate the o-ring on the bypass tube.

Torque Value:
Torque Value:
Install the aftercooler water return tube (1), tube clip, and
capscrew.
Install the connecting hose (2).
Tighten the hose clamps and capscrew.
Torque Value:
Torque Value:
Test
Engine Thermostats
Suspend the thermostat and a 100°C [212°F] thermometer
in a container of water.
NOTE: Do not allow the thermostat or thermometer to
touch the container.
Heat the water and check the thermostat as follows.
ProCarManuals.com
The nominal operating temperature is stamped on the ther-

mostat.
• Thermostat must begin to open within 2°C [3°F] of
nominal temperature.
• Thermostat must be fully open at 12°C [22°F] above
The fully open distance between the thermostat flange and
housing is 11.05 mm [0.43 in].
Remove the container from the heat. Check to see if the

thermostat returns to the closed position.
Low Temperature Aftercooling Thermostat

Suspend the thermostat and a 100°C [212°F] thermometer
in a container of water.
NOTE: Do not allow the thermostat or thermometer to
touch the container.
Heat the water and check the thermostat as follows.
The nominal operating temperature is stamped on the ther-

mostat.
• Thermostat must begin to open within 2°C [3°F] of
• Thermostat must be fully open at 8°C [15°F] above
The fully open distance between the thermostat flange and
housing is 7.8 mm [0.3 in].
ProCarManuals.com
Remove the container from the heat. Check to see if the

thermostat returns to the closed position.
Coolant Thermostat Housing Support (008-015)
Coolant Thermostat Housing Support (008-015)

General Information
LTA Cooling System The Low Temperature Aftercooling (LTA) arrangement incorporates a dual loop cooling system
that shares a single water pump.
Thermostat Support The thermostat assembly contains a support and thermostat housing. The thermostat housing
contains two thermostats (conventional aftercooling) or three thermostats (low temperature aftercooling). The support
assembly also provides for connection of the water outlet tubing for the cylinder head and the aftercooler.
Thermostat The QSK19 engines must have thermostats that do not have a vent.
The Low Temperature Aftercooling (LTA) arrangement uses two coolant thermostats and one LTA thermostat. The LTA
thermostat is located in the center position between the engine coolant thermostats.
Thermostat Seal Each thermostat has one thermostat seal.
ProCarManuals.com
Fan Drive Idler Arm Assembly (008-029)
Fan Drive Idler Arm Assembly

(008-029)
Disassemble
Remove the three mounting capscrews holding the pivot
shaft support to the alternator support.
Remove the snap ring from the idler lever.
Remove the idler lever.
Remove the oil seals.
Remove the bushings from the pivot shaft support.

ProCarManuals.com
Clean
WARNING
personal injury.
Inspect for Reuse

Inspect the parts for any damage.
Fan Drive Idler Pulley Assembly (008-030)
Assemble
Use an arbor press to install the new bushings.
Install new oil seals.
Install the idler lever into the pivot shaft support.

Install the snap ring into the snap ring groove on the idler
lever.
ProCarManuals.com
Install the pivot shaft support to the alternator support.

Install the mounting capscrews.
Fan Drive Idler Pulley Assembly

(008-030)
Clean
WARNING
personal injury.
Use solvent to clean the pulley assembly.
Inspect for Reuse

Check the clearance.
Bearing End Clearance

mm in
0.08 MIN 0.003
0.25 MAX 0.010
Rotate the pulley. Check for rough or damaged bearings.
The bearings must be replaced if any of the above con-
ditions are found.
ProCarManuals.com
Fan Hub, Belt Driven (008-036)

General Information
NOTE: For service and parts information for the fan hub with a clutch, refer to Bulletin No. 3810250, RockfordT Fan
Clutch Service and Parts Manual. For rebuild instructions for the fan hub clutch, refer to Bulletin No. 3810251, RockfordT
Clutch Overhaul Procedure.
The fan belt is tensioned by the spring loaded idler assembly and does not require adjustment.
CAUTION
The fan belt is mounted with spring tension. To avoid personal injury from being pinched between the fan hub
and fan idler, always release the spring tension before removing or installing the belt.
When the pivot arm cap is aligned properly with the spring, tension is a minimum of 68 N•m [50 ft-lb].
A grease nipple is standard on the pivot arm. The pivot arm must be greased at each scheduled maintenance
interval *.
Newer engines have a turnbuckle assembly to limit the travel of the idler pulley. Older engines have a shock absorber
to limit the travel of the idler pulley. The shock absorber can be replaced by the turnbuckle assembly. The adjustment
of the turnbuckle must be checked at each scheduled maintenance interval *. The shock absorber must be checked
for fluid leakage and loss of vibration absorption at each scheduled maintenance interval *.
Fan hubs and supports are available in various drive ratios and fan center locations. When replacing the fan hub, always
check the part number. Be sure the replacement is compatible.
All of the belt driven fan hubs contain anti-friction bearings that are the tapered roller type. Bearing end clearance is
ProCarManuals.com
controlled by the use of inner and outer bearing spacers. It is a good service practice to tag the bearings for location
during removal. Always replace the bearing and the bearing race if either piece requires replacement.
The idler pulley contains two anti-friction bearings that are the tapered roller type. The bearing end clearance is properly
set by matching select components in the kit.
CAUTION
Always replace the complete bearing kit when any piece of the idler pulley bearing assembly requires replace-
ment.
The kit includes a retaining ring, an inner spacer, two bearings, and two bearing races.
CAUTION
Never grease the bearings excessively. Too much grease will cause excessive heating due to the agitation of
the grease. Excessive agitation of the grease will result in failure.
The following is the proper method of applying water pump type grease to the fan hub or idler pulley bearings. Do not
use lithium base grease for fan hub bearings.
Pack both bearings with grease. Fill the cavity between the bearings 2/3-full of grease. Fill the cavity between the front
bearing and the end of the hub 2/3-full of grease.
* Recommended maintenance interval refers to every 250 hours, or 6 months of operation.
Clean
WARNING
personal injury.
Use solvent to clean the fan hub.
Inspect for Reuse

Inspect the fan hub for reuse. Rotate the pulley to check for
rough or damaged bearings.
Check bearing end clearance.

mm in
0.03 MIN 0.001
ProCarManuals.com
0.25 MAX 0.010

If the clearance is not within the specifications, the fan hub
must be rebuilt.
Rotate the pulley to check for rough or damaged bearings.
If the fan hub does not rotate freely, the fan hub must be
rebuilt.
Remove the pipe plugs (3). Install a grease fitting in one of

the holes.
Use a grease gun and water pump type grease. Pump
grease into the hub until it begins to come out of the open
plug hole.
Remove the grease fitting. Install the pipe plugs (3).
Assemble
CAUTION
Do not lubricate the seal surface of the shaft. The seal
and seal surface must be clean and dry.
Lightly grease the bearing (11) with MobiplexT 48 grease or
equivalent.
NOTE: Excessive grease will affect the end float reading.
Install the bearing in the hub.
CAUTION
Avoid contact with skin.
Apply LoctiteT 675 or equivalent to the outside diameter of
the seal.
Use a mandrel to install the seal (10). With the flat unseamed
face toward the shoulder of the driver, press seal in until it
bottoms.
Carefully install the fan hub seal end first over the shaft,
ensuring no damage occurs to the seal. The rear bearing
must slide easily on the shaft. If it does not, check for chips
or burrs.
ProCarManuals.com
Install the inner bearing spacer (12). The following spacers

are available to provide correct end clearance when the fan
hub has been assembled.
For two spacer style fan hubs:
a. 3627681
b. 3627682
c. 3627683
d. 3627684
For other fan hubs:
a . 3627677
b . 3627678
c . 3627679
d . 3627680
e . 3628830
Lightly grease the front bearing (8).

Install the bearing, it must slide easily over the shaft. If it
does not, check for chips and burrs.
CAUTION
Remove all grease from the threads on the shaft before
installing the lock nut. Grease on the threads reduce
the torque retention of the lock nut.
Install the hardened washer (5).
Install the lock nut (4).
Tighten the lock nut.
Use a dial indicator to measure the bearing end clearance.

mm in
0.025 MIN 0.001
0.102 MAX 0.004
If the clearance is not within specifications, rebuild the fan
hub with a suitable size spacer. Check the bearing end
clearance.
ProCarManuals.com
CAUTION
Do not use more grease than specified. Too much grease
will cause excessive heating and failure.
Use MobiplexT 48 grease or equivalent and fill the cavity
with 120 cc of grease. Grease the inner race, refit the
spacer and inner race,
Install the hardened washer (5).
Install the lock nut (4).
Check the bearing end clearance.
Install the o-ring (3) on the fan pilot (2).
Install the fan pilot and o-ring
Install the capscrews (1).
Fan, Cooling (008-040)
Fan, Cooling (008-040)

General Information
WARNING
Never attempt to rotate the engine by pulling or prying on the fan. This practice can result in serious personal
injury and damage to the fan. Use only the proper engine barring techniques to manually rotate the engine.
Check the fan for missing balance weights at each regular maintenance interval*. Do not attempt to repair broken or
bent fans, or fans with missing balance weights.
The majority of equipment that has a CumminsT engine has a radiator and a fan. The radiator and fan transfer heat
from the cooling water to the atmosphere. The fan selection process must conclude that the fan, the fan mounting
arrangement, and the fan drive system are designed and matched for compatibility.
Upon request, Cummins Application Engineering Department will assist in determining the proper selection. Refer any
fan changes, other than the direct replacement of a fan with precisely the same CumminsT part number, to the Cummins
Application Engineering Department for prior approval.
Examples that require approval are:
• Using an approved fan from one engine model on a different engine model.
• Using an approved fan on an engine with a different fan mounting arrangement.
• Using an approved fan on an engine with a different fan drive arrangement.
• Converting an engine from one market model to another.
An example is the conversion of a G-drive engine to a power unit application.
ProCarManuals.com
• Converting an engine model to a different engine model.

An example is converting a N-855 to a NT-855 model.
These examples are not inclusive. Always contact Application Engineering for assistance.
There are times when an existing fan can yield ONLY marginal cooling capability when being considered for a new
application.
WARNING
Never repitch (bend) the blades to obtain additional air delivery. Bending the blades or spider creates stress
in the construction material of the fan. Repitching (bending) will cause fan failure and can cause serious personal
injury. The proper diameter fan must be selected. Never modify an existing fan.
Application Engineering will provide assistance in the selection of a fan with the correct pitch and diameter for proper
cooling.
*Recommended maintenance interval refers to every 250 hours or 6 months of operation.
Water Pump (008-062)

Inspect for Reuse
Rotate the shaft and inspect for rough or damaged bearings.
Inspect the drive shaft for wear. If the drive shaft splines are
worn, check the female splines in the pump and in the
water pump drive.
ProCarManuals.com
Use a feeler gauge and measure the impeller-to-pump

body clearance.
Impeller Vane-To-Body Clearance

mm in
0.58 MIN 0.023
0.86 MAX 0.034
Disassemble
Remove the water inlet connection and gasket (1).
Remove the support bracket (2).
Remove the parts.

5. Shutoff valve capscrew
6. Water shutoff valve
7. Washer
8. O-ring
9. Water transfer tube (Loosen the flare nut at each end.)
10. Grommets
Discard the o-ring and grommets.
Remove the remaining capscrews (3).

Remove the inlet housing and o-ring (4).
Discard the o-ring.
ProCarManuals.com
CAUTION
The jack screw in the puller must pass easily through
the impeller bore to prevent damage to the impeller.
Use a standard puller, Part No. ST-647, or equivalent and
remove the impeller.
Remove the large retaining ring.

Support the water pump body as shown.

Use an arbor press to push on the impeller end of the shaft.
Remove the bearing and shaft assembly.
Discard the water pump seal seat.
Remove and discard the water seal and oil seal.

ProCarManuals.com
Clean
CAUTION
cleaning, follow the manufacturer’s recommendation
personal injury.
Use solvent to clean all the parts.
Inspect
Use the following formula to determine the press fit.
Press Fit = Shaft O.D. (1) minus Impeller I.D. (2).
Impeller to Shaft Press Fit

mm in
0.03 MIN 0.001
0.07 MAX 0.003
Measure the I.D. of the water pump housing bore.
Housing Bore I.D.

mm in
(13) Water Seal 36.45 MIN 1.435
36.47 MAX 1.436
(14) Oil Seal 44.43 MIN 1.749

44.48 MAX 1.751
(15) Rear Bearing 51.996 MIN 2.0471

52.215 MAX 2.0557
(16) Front Bearing 71.996 MIN 2.8345

72.215 MAX 2.8431
Inspect the bearing and shaft assembly for wear in the seal
areas.
Spin the bearings to check for roughness.
If the bearings or shaft must be replaced refer to Procedure
008-071.
ProCarManuals.com
Assemble
NOTE: The oil seal must be installed with the part number
pointing down.
Use a water pump seal mandrel, Part No. 3375320, or
equivalent and install the seal.
The seal must be no more than 0.51 mm (0.020 in.) below
the top of the step in the body.
Support the water pump housing.

Use an arbor press and water pump bearing mandrel, Part
No. 3375318, or equivalent, or push on the end of the shaft.
Install the shaft and bearing assembly.
NOTE: The beveled edge must be positioned as shown.

Install the large retaining ring.
ProCarManuals.com
Use water pump seal driver, Part No. 3376091, or equiva-

lent and install the water seal.
NOTE: The shoulder on the seal must touch the housing.
NOTE: This illustration shows the two-piece seal. This
step is the same for the one-piece seal. The water pump
seal driver must be used to adjust the spring tension
correctly.
Use an arbor press and water pump seal driver, Part No.
3376091, or equivalent and install the seal seat.
The seat dimension below applies to the one-piece and the
two-piece seal. The seal tension will not be correct if the
seat dimension is not within specifications.
Seat Dimension
mm in
10.52 MIN 0.414
10.57 MAX 0.416
CAUTION
More than one drop will glue the faces of the seal to-
gether. It can result in damage to the seal.
Apply one drop of LoctiteT 290, or equivalent to the seal
seat as shown.
Apply a smooth coating of LoctiteT 609, or equivalent to the

I.D. of the impeller as shown.
Use an arbor press and a mandrel to install the impeller to

ProCarManuals.com
the specified clearance.

NOTE: Use a feeler gauge in the water outlet port to mea-
sure the clearance.
Impeller Vane to Body Clearance

mm in
0.58 MIN 0.023
0.86 MAX 0.034
Install the washer (7).

Use vegetable oil to lubricate the o-ring (8). Install the
o-ring.
Install the shutoff valve.
Install the capscrew (5).
Use vegetable oil to lubricate the new grommets (10).
Install the transfer tube.

Install the parts as shown.
Install the inlet connection (1), gasket, and capscrews.

NOTE: Do not tighten the support bracket until the water
pump is assembled to the engine.
Install the support bracket (2).
ProCarManuals.com
Torque Converter Cooler (008-065)

General Information
The engine mounted torque converter cooler is available as an option. This option can be added to a standard engine
by purchasing the torque converter cooler housing, the cooler cover, and the elements.
The location of the turbocharger oil drain line, turbocharger water supply line, and the other components will have to
be changed on some engines. The torque converter cooler is mounted and replaces the lubricating oil cooler cover.
When the torque converter cooler option is selected, longer mounting capscrews must be used. With the torque
converter cooler option, the turbocharger water supply line must also be moved from the oil cooler cover to a fitting
in the top of the torque converter cooler housing.
Exploded View
ProCarManuals.com
1. Cover, Torque Converter Oil

2. Gasket, Lubricating Oil Cooler Cover
3. O-ring
4. Element, Lubricating Oil Cooler
5. Housing, Torque Converter Cooler
6. Nut, Self-Locking
7. Capscrew, Lock Washer, and Plain Washer
8. Capscrew and Lock Washer
Inspect for Reuse

NOTE: Heating the water in the tank to 50° C [120° F] will
improve the test results.
Pressure test the elements.
Apply air pressure, and check for leaks.
NOTE: Discard the elements if any debris is found, the
engine has had a debris causing failure, or the torque
converter has failed.
Air Pressure
kPa psi
415 MAX 60
Discard the elements if any leaks are present.
Assemble
Install the elements.
Torque the self-locking nuts.
Use vegetable oil adn lubricate the new o-rings.
ProCarManuals.com
Install the new o-rings.
Install the gasket and cooler cover.

Torque the capscrews in the sequence shown.
NOTE: Use Loctite 592, or equivalent to seal heater plug.

Apply a smooth coating of sealant to the threads of the
heater plug.
Install and torque the heater plug
Water Pump Bearings (008-071)
Disassemble
Remove the torque converter cover mounting bolts and
cover.
NOTE: The cover must be pried from the housing, because
of the tight fit between the cover and the o-rings on the
elements.
Remove the cooling elements.
Clean
Use a solvent that will not harm copper and clean the
elements.
Use a solvent that will not harm aluminum and clean the
housing and cover.
ProCarManuals.com

Remove
Use a water pump bearing separator, Part No. 3375326, or
equivalent, to disassemble the bearing and shaft assem-
bly.
Remove the retaining ring (1).
Remove the front bearing (2).
Remove the rear bearing (3).
Measure
Measure the shaft O.D. and the bearing I.D. Compare the
differences.
Bearing to Shaft Differences

mm in
Clearance 0.003 MAX 0.0001
Interference 0.018 MAX 0.0007
Install
CAUTION
The mandrel must make contact on the inner race of the
bearing to prevent damage to the bearing.
Support the shaft.
Use an arbor press and a water pump bearing mandrel,
Part No. ST-658 (4), or equivalent, install the bearings.

ProCarManuals.com
NOTES
ProCarManuals.com
Section 9 - Drive Units - Group 09 Page 9-a
Section 9 - Drive Units - Group 09

Section Contents
Page
Accessory Drive Pulley .................................................................................................................................... 9-3
Install ........................................................................................................................................................... 9-3
Remove ........................................................................................................................................................ 9-3
Drive Units - General Information.................................................................................................................... 9-1
Fuel Pump Drive .............................................................................................................................................. 9-5
Assemble .................................................................................................................................................... 9-10
Clean ........................................................................................................................................................... 9-7
Disassemble ................................................................................................................................................ 9-9
Exploded View .............................................................................................................................................. 9-6
Fuel Pump Drive Gear and Shaft ................................................................................................................... 9-11
Assemble ................................................................................................................................................... 9-12
Disassemble ............................................................................................................................................... 9-11
Hydraulic Pump Drive .................................................................................................................................... 9-14
Assemble ................................................................................................................................................... 9-16
Clean ......................................................................................................................................................... 9-15
ProCarManuals.com
Disassemble ............................................................................................................................................... 9-15

Exploded View ............................................................................................................................................ 9-14
Hydraulic Pump Drive Gear and Shaft .......................................................................................................... 9-17
Assemble ................................................................................................................................................... 9-18
Disassemble ............................................................................................................................................... 9-17
Hydraulic Pump Support Bushing ................................................................................................................. 9-57
Install ......................................................................................................................................................... 9-58
Remove ...................................................................................................................................................... 9-57
Outer Hydraulic Pump Support Drive............................................................................................................ 9-53
Assemble ................................................................................................................................................... 9-56
Disassemble ............................................................................................................................................... 9-53
Install ......................................................................................................................................................... 9-55
Rear Gear Drive (Lower Assembly)................................................................................................................ 9-18
Assemble ................................................................................................................................................... 9-26
Disassemble ............................................................................................................................................... 9-25
Exploded View ............................................................................................................................................ 9-23
Install ......................................................................................................................................................... 9-29
Remove ...................................................................................................................................................... 9-18
Rear Gear Drive (Upper Assembly) ............................................................................................................... 9-35
Assemble .......................................................................................................................................... 9-42, 9-50
Disassemble ...................................................................................................................................... 9-37, 9-49
Exploded View.................................................................................................................................... 9-35, 9-48
Inspect for Reuse .............................................................................................................................. 9-40, 9-49
Service Tools ................................................................................................................................................... 9-2
Drive Units .................................................................................................................................................... 9-2
Water Pump Drive Bushing............................................................................................................................ 9-52
Assemble ................................................................................................................................................... 9-52
Disassemble ............................................................................................................................................... 9-52
Water Pump Drive Gear and Shaft................................................................................................................. 9-51
Assemble ................................................................................................................................................... 9-52
Disassemble ............................................................................................................................................... 9-51
Page 9-b Section 9 - Drive Units - Group 09
Page
Water Pump Drive Pulley ............................................................................................................................... 9-52
Clean ......................................................................................................................................................... 9-52
ProCarManuals.com
Drive Units - General Information
Section 9 - Drive Units - Group 09 Page 9-1
Drive Units - General Information

General Information
The accessory drive housing is manufactured of aluminum. The aluminum housing does not contain a bushing, and
does not require thrust washers.
CAUTION
Installation of an air compressor on a fuel pump drive housing will result in failure due to the lack of lubrication.
The housings are available in two designs, with and without provisions for mounting an air compressor. Those without
air compressors do not have provisions for a compressor oil pressure and drain-back. The fuel pump drive has
provisions for a lovejoy coupling. The compressor drive has provisions for a splined sleeve-type coupling. The
procedures are identical for both of the designs.
The fuel pump/compressor drive gear has stamped marks. The stamped marks must be aligned properly with the
camshaft idler gear so that valve and injector adjustment marks on the accessory drive pulley are oriented correctly.
The retainer capscrew on the compressor drive (splined half-coupling) is special. It has a drilling in it that provides
lubrications of the splined coupling. The retainer capscrew on the fuel pump drive (lovejoy half-coupling) does not have
an oil drilling.
ProCarManuals.com
Service Tools
Page 9-2 Section 9 - Drive Units - Group 09
Service Tools
Drive Units

Gear Puller
Used to remove the drive pulleys and impellers.
ST-647
ProCarManuals.com

Used to install drive pulleys.
3376326
Coupling Puller
Used to remove accessory drive coupling.
3376663

3824760
Pipe Sealant
Use when installing pipe plugs or cup plugs on the engine in order
to prevent leaks.
3375066
Dowel Pin Extractor

Used to pull dowel pins.
ST-1134
Accessory Drive Pulley (009-004)

Remove
CAUTION
Use a capscrew in the shaft to prevent damage to the
shaft threads.
Install a [7/16-20x1 in] capscrew in the shaft.
Use a standard puller, Part No. ST–647, or equivalent.
Remove the accessory drive pulley.
Use a brass drift and remove the woodruff key from the
shaft.
Remove the capscrew from the shaft.
Remove the keyway seal.
Inspect for Reuse

Visually inspect the pulley for cracks, wear in the belt
grooves, or other damage.
ProCarManuals.com
Inspect the mating surface and pulley bore areas for

damage.
Install
NOTE: The keyway seal must be installed before installing
the woodruff key.
Install the woodruff key.
CAUTION
Use pulley installation tool kit, Part No. 3376326. Insert the
appropriate adapter (7) in the pusher.
ProCarManuals.com
step on the shaft.
Fuel Pump Drive (009-011)

General Information
The accessory drive housing is manufactured of aluminum. The aluminum housing does not contain a bushing, and
does not require thrust washers.
CAUTION
Installation of an air compressor on a fuel pump drive housing will result in failure due to the lack of lubrication.
NOTE: The housings are available in two designs, with and without provisions for mounting an air compressor. Those
without air compressors do not have provisions for a compressor oil pressure and drain-back. The fuel pump drive
has provisions for a lovejoy coupling. The compressor drive has provisions for a splined sleeve-type coupling. The
procedures are identical for both of the designs.
The fuel pump/compressor drive gear have stamped marks. The stamped marks must be aligned properly with the
camshaft idler gear so that valve and injector adjustment marks on the accessory drive pulley are oriented correctly.
The retainer capscrew on the compressor drive (splined half-coupling) is special. It has a drilling in it that provides
lubrications of the splined coupling. The retainer capscrew on the fuel pump drive (lovejoy half-coupling) does not have
an oil drilling.
ProCarManuals.com
Exploded View
ProCarManuals.com
1. Coupling, Lovejoy Type (Upper)

1. Coupling, Spline Type (Lower)
2. Gear, Air Compressor and Fuel Pump Drive
3. Key, Plain Woodruff
5. Shaft, Accessory Drive
6. Washer, Clamping
7. Bearing, Thrust
8. Bearing, Thrust
9. Housing, Accessory Drive
10. Bushing, Accessory Drive
12. Capscrew, Special
15. Washer, Plain
19. Gasket, Accessory Drive Support
22. Pulley, Accessory Drive
23. Sleeve, Wear
24. Key, Plain Woodruff
25. Slinger, Oil
26. Seal, Oil
Clean
WARNING
personal injury.
Use solvent to clean the outer housing of the fuel pump
drive.
Inspect for Reuse

Measure the end clearance.
Fuel Pump/Compressor Drive End Clearance

mm in
0.05 MIN 0.002
0.30 MAX 0.012
ProCarManuals.com
Check the teeth of the gear for damage.

The coupling washer must be positioned tightly between
the coupling and the shaft.

Measure the I.D. If the bushing must be replaced refer to
Bushing I.D.
mm in
33.43 MIN 1.316
33.50 MAX 1.319
NOTE: An aluminum housing does not contain a bushing.
Measure the housing I.D. It must be identical to the bush-
ing I.D. in a cast iron housing.
Check the grooved surface for damage.


mm in
2.36 MIN 0.093
2.41 MAX 0.095
NOTE: On an aluminum housing ONLY, check the two

machined thrust surfaces for damage.
Use a depth micrometer.
Housing Depth
mm in
45.54 MIN 1.793
ProCarManuals.com
45.67 MAX 1.798
Check the teeth of the gear for damage.
Shaft O.D.
mm in
(5) 34.963 MIN 1.3765
34.976 MAX 1.3770
(6) 34.662 MIN 1.5616
39.674 MAX 1.5620
(7) 33.30 MIN 1.300
33.33 MAX 1.312
(8) 25.476 MIN 1.0030
25.489 MAX 1.0035
NOTE: If the gear or shaft must be replaced, refer to Pro-
cedure 009–013.
Measure the I.D. of the pulley.
Pully I.D.
mm in
34.912 MIN 1.3745
34.938 MAX 1.3755
Measure the I.D. of the coupling.
Lovejoy Coupling I.D.

mm in
25.425 MIN 1.0010
25.438 MAX 1.0015
Spline Coupling I.D.

mm in
25.400 MIN 1.0000
25.425 MAX 1.0010
Disassemble
Remove the special capscrew and the washer.
CAUTION
Install the capscrew back into the drive unit without the
washer until it touches the shaft to prevent damage to
the shaft.
ProCarManuals.com
Use a coupling puller (1), Part No. 3376663, or equivalent,

to remove the coupling.
Use a 3-jaw puller to remove the lovejoy type coupling.
Remove the coupling.
Remove the capscrew.
Remove the following:

2. Clamping washer
3. Inner thrust bearing
4. Outer thrust bearing
Remove the gear and the shaft assembly.
Remove the pipe plug from the housing.
NOTE: Aluminum housings do not contain thrust bearings.
Assemble
Position the grooved surface of the thrust bearing as shown.
Install the thrust bearing.
NOTE: An aluminum housing does not contain thrust
bearings.
Use LubriplateT No. 105, or equivalent. Lubricate the

grooved surface of the thrust bearing (3).
NOTE: An aluminum housing does not contain thrust bear-
ings. Lubricate the machined thrust surface.
With the grooved surface positioned up, slide the thrust
bearing (3) over the shaft.
Before installing the clamping washer (2), the beveled edge
must be positioned as shown.
ProCarManuals.com
Support the gear or the shaft.

Install the coupling.
Use an arbor press and a mandrel to push the coupling until
it touches the clamping washer.
The clamping washer must be positioned tightly between
the coupling and the shoulder of the shaft.
Install the pipe plug into the housing.
Tighten the pipe plug.
CAUTION
The capscrew must contain an oil drilling if an air com-
pressor is to be mounted on the engine.
Install the washer and the capscrew.
Check the capscrew size for the correct torque value.
Capscrew Length Torque
3/8 in 45 Nm [35 ft-lb]

1/2 100 Nm [75 ft-lb]
Fuel Pump Drive Gear and Shaft (009-013)
Rotate the shaft to check for correct assembly.

Use a dial indicator. Measure the end clearance.
End Clearance
mm in
0.05 MIN 0.002
0.30 MAX 0.012
If the end clearance is not within specifications, be sure the
coupling is positioned tightly against the clamping washer.
NOTE: Oversize thrust bearings are available to adjust the
end clearance.
Fuel Pump Drive Gear and Shaft

(009-013)
Disassemble
Support the gear.
Use an arbor press to remove the shaft.
ProCarManuals.com
Measure the gear I.D.
Gear I.D.
mm in
39.73 MIN 1.564
39.75 MAX 1.565
Remove the key and check for damage.

NOTE: If damage is found, the key must be replace.
Measure the O.D. at the gear location.
Shaft O.D.
mm in
39.789 MIN 1.5665
39.802 MAX 1.5670
Assemble
Support the gear.
Use engine oil to lubricate the shaft.
Align the key with the key slot in the gear. Use an arbor
press to press the shaft through the gear until the shoulder
of the shaft touches the gear.
NOTE: If an adequate press is not available, an oven can

be used.
WARNING
burns.
CAUTION
Do not exceed the specified time or temperature. Dam-
ProCarManuals.com
age to the gear teeth will result.

Heat the gear at 235°C (450°F) no less than one hour, and
no more than six hours.
Use LubriplateT No. 105, or equivalent to lubricate the

grooved surface of the thrust bearing.
NOTE: On an aluminum housing ONLY, lubricate the
grooved area machined in the housing.
Install the shaft and the gear.
WARNING
burns.
Slide the shaft in the gear.
CAUTION
Allow the air to cool the gear. Do not use water or oil to
reduce the cooling time. Damage to the gear can result.
Use a feeler gauge to measure the distance between the
shoulder of the shaft and the gear.
Fuel Pump Drive Gear to Shaft

mm in
0.05 MAX 0.002
NOTE: If the distance between the gear and the shaft is not
within specification press the gear on until specifications
are meet.
ProCarManuals.com
Hydraulic Pump Drive (009-016)

General Information
A hydraulic pump can be mounted on the front or at the rear of the gear cover.
The SAE A two-bolt type flange is required to mount a hydraulic pump at the rear of the gear cover. The SAE B four-bolt
type flange is required for a hydraulic pump to be mounted on the front of the gear cover. There is a specific drive
required to match the different sizes of spline drives required for the optional hydraulic pumps.
Engines that do not have a hydraulic pump drive must have parts that block the oil holes in the gear cover and housing
for correct engine oil pressure. A four-bolt flange that has a blind plug welded to it must be installed on the front of
the gear cover. The blind plug will extend into the bushing, blocking the oil drilling. A three-bolt cover that has two
o-rings must be installed on the rear of the gear housing.
A hydraulic pump drive can be installed by removing the blind plug flange and the cover. If only the rear drive port is
used, a plain four-bolt cover and gasket must be installed on the front of the cover. If only the front drive port is used,
a two-bolt cover and gasket must be installed on the rear of the pump drive.
Exploded View
ProCarManuals.com
1. Gear, Hydraulic Pump Drive

2. Shaft, Hydraulic Pump Drive
3. Bearing, Thrust
4. Housing, Hydraulic Pump Drive
5. Bearing, Thrust
6. Washer, Clamping
7. Ring, Retaining
8. Gasket
9. Cover, Hydraulic Pump
10. Lock Washer and Locknut
Clean
Remove the capscrews and the lockwashers.
Remove the cover from the pump.
WARNING
cleaning, follow the manufacture’s recommendation for
use. Wear goggles and protective clothing to avoid per-
sonal injury.
Remove adn discard the gasket.
Use solvent to clean the drive.
Inspect for Reuse

Measure the clearance.
End Clearance
mm in
0.13 MIN 0.005
0.48 MAX 0.019
If the end clearance is not within specifications, the as-
ProCarManuals.com
sembly must be rebuilt. Refer to the Procedure, 009-006.

Install the cover on the pump.
Install the lockwashers and the capscrews.
Disassemble
Remove the capscrews and the lockwashers.
Remove the cover.
Remove the retaining ring.
Remove the clamping washer.

Remove the thrust bearing.
ProCarManuals.com
Remove the housing.

Remove the thrust bearing.
Assemble
Use LubriplateT No. 105 or equivalent to lubricate the
Position the grooved surface of the thrust bearing as illus-
trated (3).
Slide the shaft in the housing.
NOTE: The gear must touch the thrust bearing.
Hydraulic Pump Drive Gear and Shaft (009-019)
Use LubriplateT No. 105 or equivalent to lubricate the

With the grooved surface positioned up, slide the thrust
bearing over the shaft.
The beveled edge of the clamping washer must be posi-
tioned against the thrust bearing. Slide the clamping washer
over the shaft.
The beveled edge of the retaining ring must be positioned
as illustrated. Install the retaining ring.
Measure the clearance.
End Clearance
mm in
0.13 MIN 0.005
0.48 MAX 0.019
If the end clearance is not within specifications, the as-
sembly must be rebuilt. Refer to Procedure 009-016.
ProCarManuals.com

Install the cover.
Install the lockwashers and the capscrews.
Hydraulic Pump Drive Gear and Shaft

(009-019)
Disassemble
ONLY remove the gear from the shaft when the gear or the
shaft must be replaced.
Use an arbor press to remove the gear.
Rear Gear Drive (Lower Assembly) (009-023)
Assemble
Use LoctiteT 609 or the equivalent, apply a smooth layer on
the I.D. of the gear.
Support the gear and position the part number down.
Use an arbor press to press the shaft through the gear until
the shaft shoulder touches the gear.
Rear Gear Drive (Lower Assembly)

(009-023)
Remove
Remove the upper rear gear drive assembly. Refer to Pro-
cedure 009-024.
ProCarManuals.com
Remove the transmission, clutch, and all related compo-

nents. Refer to the equipment manufacturer’s instructions.
CAUTION
component.
Remove the starting motor capscrews, starter, spacers, and
gaskets.
NOTE: Not All engines contain spacers. Only engines with
wet type flywheel housings contain gaskets.
CAUTION
component.
Use a 5/8 in guide stud.
Remove one capscrew and install the guide stud.
tee handles. Remove the remaining capscrews.
Remove the flywheel.
NOTE: Use a mallet to tap the flywheel from the crankshaft
if necessary.
WARNING
with used engine oil. Always use the proper procedure
to dispose of the used oil.
ProCarManuals.com
CAUTION
Hot oil can cause personal injury.
Drain the oil when the oil temperature is less than 60°C
[140°F].
Remove the drain plugs from the sump and adapter cover
to drain the oil.
Replace the copper washers and plugs.
Tighten the drain plugs.
Remove the capscrews and the rear crankshaft seal.

Remove and discard the o-ring and seal.
Remove the adapter cover plate or the oil pan (whichever

is in the rear position).
Angle the cover plate to allow the oil to drain.
CAUTION
component.
Put a wooden block the width of the oil pan adapter be-
tween the support and the oil pan adapter to prevent dam-
age to the engine.
ProCarManuals.com
Use a jack stand or a suitable lifting fixture to support the

rear of the engine. Put the support in position to allow
access to the capscrews in the oil pan adapter that attach
to the flywheel housing.
Remove the rear engine mounts from the flywheel housing

if necessary.
Remove the two 7/16 in capscrews and the five 3/8 in

capscrews that attach the oil pan adapter to the flywheel
housing.
CAUTION
Be sure the rear gear train lower housing is secure
BEFORE removing the flywheel housing. The lower
housing rests on the guide studs and dowel pins, but is
NOT fastened to the block.
CAUTION
component.
Use two 5/8x6-1/2 in guide studs. Remove two capscrews.
Install the guide studs.
Use a hoist, a tee handle, and a lifting sling. Install the tee
handle.
Adjust the hoist until there is tension in the lifting sling.
Remove the remaining capscrews, lockwashers, and nuts.
NOTE: Two pry bars can be used to separate the lower

housing of the rear gear train from the flywheel housing.
Use a mallet to tap the flywheel housing off the two locating
ProCarManuals.com
dowels.
Remove and discard the rectangular seal and the bolt
seals.
tee handles. Adjust the hoist until there is tension in the
lifting sling.
Use a mallet to tap the lower housing of the rear gear train
off the two locating dowel pins in the rear face of the
cylinder block.
Remove and discard the rectangular seal, bolt seals, and
main oil rifle seal.
ProCarManuals.com
Exploded View
ProCarManuals.com
Rear Gear Drive

Rear Gear Drive Exploded View Table 42. Gasket, Hydraulic Pump Flange Cover
1. Dowel Pin 43. Cover, Hydraulic Pump Flange
2. Seal, Rectangular Ring 44. Bearing, Thrust
3. Dowel Pin 45. Spacer, Bearing
4. Capscrew, Hexagon Head 46. Support, Hydraulic Pump
5. Seal, Rectangular Ring 47. Bushing
6. Bearing, Thrust 48. Ring, Retaining
7. Seal, Rectangular Ring 49. Gear, Hydraulic Pump
8. Housing, Gear 50. Shaft and Plug Assembly
9. Plug, Pipe 51. Plug, Expansion
10. Seal, Rectangular Ring 52. Ring, Retaining
11. Plug, Expansion 53. Capscrew, Hexagon Head
12. Shaft, Idler 54. Washer, Lock
13. Gear and Bushing, Hydraulic Pump 55. Washer, Lock
14. Seal, O-ring 56. Plate, Cover
15. Washer, Lock 57. Gasket, Hydraulic Pump
16. Washer, Plain 58. Adapter, Hydraulic Pump
17. Dowel Pin 59. Gasket, Hydraulic Pump
18. Capscrew, Hexagon Head 60. Capscrew, Hagen Head
19. Gasket, Hydraulic Pump 61. Adapter, hydraulic Pump
20. Capscrew, Hexagon Head 62. Washer, Lock
21. Capscrew, Hexagon Head 63. Capscrew, Hexagon head
22. Capscrew, Hexagon Head 64. Gasket, Support, Hydraulic
23. Plug, Pipe 65. Capscrew, Hexagon Head
ProCarManuals.com
25. Housing, Hydraulic Drive 67. Washer, Lock

26. Bushing 68. Plate, Cover
27. Support, Hydraulic Pump 69. Gasket, Hydraulic Pump
28. Bushing 70. Gasket, Hydraulic Pump
29. Seal, O-ring 71. Adapter, Hydraulic Pump
30. Capscrew, Hexagon Head 72. Assembly, Coupling and Adapter
31. Bearing Thrust 73. Bearing, Thrust
32. Spacer, Bearing 74. Spacer, Bearing
33. Ring, Retaining 75. Gear, Hydraulic Pump
34. Gear, Hydraulic Pump 76. Support, Hydraulic Pump
35. Shaft and Plug Assembly 77. Bushing
36. Ring, Retaining 78. Ring, Retaining
37. Washer, Lock 79. Gear, Hydraulic Pump
38. Capscrew, Hexagon Head 80. Shaft and Plug Assembly
39. Gasket, Support, Hydraulic 81. Ring, Retaining
40. Capscrew, Hexagon Head
41. Washer, Lock
Disassemble
Remove the three capscrews from the idler shaft.
If the idler shaft has three holes, use a soft punch and a
mallet. Rotate the idler shaft 30 degrees until the capscrew
holes in the housing are not visible through the capscrew
holes in the idler shaft.
ProCarManuals.com
Use three 3/8-24x2 in capscrews. Make sure the idler gear

is secure.
Alternately tighten the capscrews to pull the shaft from the
housing.
Remove the shaft, thrust washers, and gear.
If the idler shaft has five holes, use two 3/8–24x2 in

capscrews. Make sure the idler gear is secure.
Alternately tighten the capscrews to pull the shaft from the
housing.
Inspect for Reuse

Remove all pipe plugs and clean all oil drillings. Be sure the
oil drillings intersect.
Clean and check the lower housing for damage.
CAUTION
Check for debris in the main oil rifle. Any debris will
cause rear gear train damage.
Be sure the 1-1/8 in expansion plug is not installed in the
end of the main oil rifle in the cylinder block. The main oil
rifle must be OPEN to allow the oil to the rear gear train.
ProCarManuals.com
Inspect the two rear gear train housing dowel pins in the
rear face of the cylinder block. Any damaged dowels must
be replaced.
Use dowel pin extractor, Part No. ST-1143, to remove the
dowel pins. Use a brass or lead hammer to install the new
dowel pins.
Assemble
The five hole style idler shaft does not have a hole for the
internal hex pipe plug.
Use LoctiteT to install the internal hex pipe plug into the end
of the idler shaft.
NOTE: Absence of the pipe plug can cause serious engine
damage due to a loss in oil pressure to the rear gear train
bushings.
Use pipe sealant, Part No. 3375066, or equivalent sealant

with liquid TeflonT. Install five 1/8 in internal hex pipe plugs
into the lower housing.
Position the lower housing horizontally with the block mat-

ing surface facing up. Attempting to install the gear and
idler shaft with the housing vertical can result in binding of
the thrust bearings.
ProCarManuals.com
Use LubriplateT 105 or equivalent. Lubricate one thrust

bearing and the counterbore in the lower housing near the
expansion plug. Install the thrust bearing into the count-
erbore with the grooved side facing away from the housing.
Install 5/16–18x2 in guide studs.

Align the idler gear into the lower housing. Align and install
the idler shaft into the idler gear and lower housing until the
idler shaft pilot chamfer touches the lower housing.
Make sure the machined surface on the back side of the

lower housing is supported to prevent cracking of the hous-
ing.
Use an arbor press to press the idler shaft into the lower
housing until the mounting flange contacts the housing.
Remove the guide studs and install the three 5/16-18x3/4

in capscrews.
Tighten the three capscrews.
ProCarManuals.com
Rotate the gear to check for binding.
Use a dial indicator.

Measure the idler gear end clearance.
Idler Gear End Clearance

mm in
0.10 MIN 0.004
0.51 MAX 0.020
NOTE: If the end clearance is not within specifications, the
thrust bearings must be replaced.
Install
NOTE: If an SAE 1 flywheel housing option is used, there
must be two [5/8–11 x 6 1/2 in] studs, Part No. 3065777,
installed in the upper holes of the cylinder block.
Apply a small amount of LubriplateT 105 or gasket adhesive
on the seal ring groove, the capscrew counterbores, and
the dowel counterbores on the block side of the lower
housing.
Install the new rectangular seal ring, with the joint at the top
into the groove in the lower housing.
Install the ten new capscrew seals into the capscrew
Use LubriplateT 105 or equivalent on the main rifle seal.
Install the main rifle seal into the counterbore surrounding
the main rifle drilling.
CAUTION
Caution: The component weighs 23 kg [50 lb] or more.
To avoid personal injury, use a hoist or get assistance
to lift the components.
ProCarManuals.com
Install two 5/8-11x1/2 inch guide studs into the rear face of
the cylinder block. Use a hoist, two tee handles, and a
lifting sling. Install the tee handles.
Lift the lower housing of the rear gear train.
Install the lower housing of the rear gear train onto the
dowel pins.
Check the alignment of all capscrews seals, rectangular
seal, and the main oil rifle seal.
Use two 5/8-11x5 inch capscrews with flat washers in the
locations shown.
Tighten the capscrews alternately to pull the lower housing
to the block.
Use a dial indicator. Be sure the two capscrews are holding

the lower housing firmly against the cylinder block. Check
the gear lash.
Lower Housing-To-Cylinder Block Gear Backlash

mm in
0.05 MIN 0.002
0.51 MAX 0.015
If the gear lash is above acceptable limits, the rear gear
train lower idler gear or crankshaft gear must be replaced.
NOTE: Replace the idler gear first.
If the gear lash is below acceptable limits (or if the gear
replacement does not correct the lash), replace the
housing.
Use LubriplateT No. 105 or gasket adhesive on the seal ring

groove and the 10 capscrew counterbores on the rear gear
train lower housing side of the flywheel housing.
Install the new rectangular seal ring, with the joint at the
top, into the groove in the flywheel housing.
Install the new capscrew seals and dowel seals into the
ProCarManuals.com
CAUTION
personal injury, use a hoist or get assistance to life the
component.
Use two 5/8-11x6 1/2 inch guide studs. Use a hoist, tee
handles, and a lifting sling. Install the flywheel housing onto
the dowels in the rear gear train lower housing.
Install the lock washers, capscrews, and nuts.
Use the following steps.

Tighten using the sequence shown.
2 205 N•m [150 ft-lb]
Install the two capscrews 7/16-14x4 3/4 inch, Part No.

190799, and the five capscrews 3/8-16x4 3/4 inch, Part No.
S106-C, with flat washers and lockwashers.
Torque Value:
3/8-16 inch 45 N•m [35 ft-lb]
7/16-14 inch 65 N•m [50 ft-lb]
Install the upper housing of the rear gear train.

ProCarManuals.com
Use gasket adhesive on the gasket. Do not use an exces-

sive amount of adhesive on the gasket.
Align and install the rear gear train upper housing gasket
to the rear gear train lower housing.
CAUTION
The component weighs 23 kg [50 lbs.] or more. To avoid
component.
NOTE: Use extra care when aligning the upper housing
onto the lower housing to prevent gasket damage.
Use the dowel pins to align the upper housing onto the
lower housing.
Use only SAE Grade 8 capscrews to install the upper

housing. Install the following capscrews according to the
table below.
Ref Location Part No. Size [inch] Qty
1 Top-Front 3202224 1/2-13 x 9 2
1/4
2 Top-Rear 3202223 1/2-13 x 7 2
1/2
3 Internal 1691695 1/2-13 x 1 4
3/4
4 Bottom-Left Side 3202222 1/2-13 x 1 2
3/4
5 Bottom-Right Side 3202222 1/2-13 x 1 3
3/4
Use the sequence shown to tighten the bolts.

Torque Value:
Step 2 150 N•m [110 ft-lb]
ProCarManuals.com
Use a dial indicator. Be sure the lower idler gear is secure.

If the gear is not secure, the indicator reading will include
the lower idler gear to the crankshaft gear backlash.
Idler Gear Backlash

mm in
0.05 MIN 0.002
0.51 MAX 0.020
If the gear lash is less than specified limits, thicker gaskets

are available. Do not use more than two gaskets to correct
the backlash.
If the gear lash is greater than the specification and the
thinnest gasket is used, the upper and lower gears must
be replaced.
Use LubriplateT No. 105, or equivalent. Lubricate the outer

hydraulic pump support bushing in the upper housing.
Lubricate the bushing surfaces on both shafts in the outer
Install the outer hydraulic pump support drive.

Use gasket adhesive sparingly. Install the hydraulic sup-
ProCarManuals.com

3/8–16 x 1-1/4 inch capscrew.
Use three 7/16-14 x 4 inch guide studs. Install one outer

Install four capscrews.

Hand-tighten the capscrews.
Install the remaining three capscrews. Use the sequence
and torque as shown.
Install the other outer hydraulic pump using the same

procedure.
ProCarManuals.com
Rear Gear Drive (Upper Assembly) (009-024)

Exploded View
ProCarManuals.com
Rear Gear Drive

Rear Gear Drive Exploded View Table 42. Gasket, Hydraulic Pump Flange Cover
1. Dowel Pin 43. Cover, Hydraulic Pump Flange
2. Seal, Rectangular Ring 44. Bearing, Thrust
3. Dowel Pin 45. Spacer, Bearing
4. Capscrew, Hexagon Head 46. Support, Hydraulic Pump
5. Seal, Rectangular Ring 47. Bushing
6. Bearing, Thrust 48. Ring, Retaining
7. Seal, Rectangular Ring 49. Gear, Hydraulic Pump
8. Housing, Gear 50. Shaft and Plug Assembly
9. Plug, Pipe 51. Plug, Expansion
10. Seal, Rectangular Ring 52. Ring, Retaining
11. Plug, Expansion 53. Capscrew, Hexagon Head
12. Shaft, Idler 54. Washer, Lock
13. Gear and Bushing, Hydraulic Pump 55. Washer, Lock
14. Seal, O-ring 56. Plate, Cover
15. Washer, Lock 57. Gasket, Hydraulic Pump
16. Washer, Plain 58. Adapter, Hydraulic Pump
17. Dowel Pin 59. Gasket, Hydraulic Pump
18. Capscrew, Hexagon Head 60. Capscrew, Hexagon Head
19. Gasket, Hydraulic Pump 61. Adapter, hydraulic Pump
20. Capscrew, Hexagon Head 62. Washer, Lock
21. Capscrew, Hexagon Head 63. Capscrew, Hexagon head
22. Capscrew, Hexagon Head 64. Gasket, Support, Hydraulic
ProCarManuals.com
25. Housing, Hydraulic Drive 67. Washer, Lock

26. Bushing 68. Plate, Cover
27. Support, Hydraulic Pump 69. Gasket, hydraulic Pump
28. Bushing 70. Gasket, Hydraulic Pump
29. Seal, O-ring 71. Adapter, Hydraulic Pump
30. Capscrew, Hexagon Head 72. Assembly, Coupling and Adapter
31. Bearing Thrust 73. Bearing, Thrust
32. Spacer, Bearing 74. Spacer, Bearing
33. Ring, Retaining 75. Gear, Hydraulic Pump
34. Gear, Hydraulic Pump 76. Support, Hydraulic Pump
35. Shaft and Plug Assembly 77. Bushing
36. Ring, Retaining 78. Ring, Retaining
37. Washer, Lock 79. Gear, Hydraulic Pump
38. Capscrew, Hexagon Head 80. Shaft and Plug Assembly
39. Gasket, Support, hydraulic 81. Ring, Retaining
40. Capscrew, Hexagon Head
41. Washer, Lock
Disassemble
NOTE: The hydraulic pump supports and the hydraulic
pump adapters can be different. Mark the parts for loca-
tion.
Remove the hydraulic pump support and the hydraulic
pump adapters or cover plates. Remove and discard the
gaskets.

drive. These engines require a cover plate and a non-
splined shaft, but do not use a hydraulic gear.
If using a cover plate, remove the cover plate and nonsplined
shaft.
Remove the seven capscrews from each outboard hydrau-
lic drive or cover plate.
ProCarManuals.com
CAUTION
component.
WARNING
Care MUST be taken to avoid possible breakage of the
capscrew mounting flanges.
The outboard hydraulic pump supports must be rotated to
remove from the housing. Use a mallet. Carefully tap the
side of the support.
Use a pry bar to remove both outboard hydraulic pump

supports.
CAUTION
component.
Use a hoist and lifting sling. Install the lifting sling around
both sides of the upper housing. Adjust the hoist until there
is tension in the lifting sling.
CAUTION
The center gear in the drive protrudes from the bottom
of the housing. Use wood blocks to raise the housing
and prevent the gear from being damaged.
Remove the four capscrews from the top of the housing (A),
the four internal capscrews (B), the two capscrews from the
bottom of the upper housing on the left side (C), and the
three capscrews from the bottom on the right side (D).
ProCarManuals.com
Remove the rear gear train upper housing from the lower
housing. Remove the gasket. Keep the gasket for future
use.
Remove the center hydraulic pump adapter and/or cover

plate. Remove and discard the gaskets.
Remove the four capscrews from the hydraulic pump sup-

port an the engine side of the upper housing.
Use two 1/4–20x2 inch capscrews. Alternately tighten the
capscrews to pull the support plate from the housing.
Remove the tapered retaining ring from the hydraulic pump

drive shaft on the pump side.
Remove the bearing spacer and the thrust bearing. Check
the bearing spacer for wear against the shaft shoulder.
Make sure the center drive gear will not drop. Remove the
drive shaft from the upper housing.
Remove the gear.
ProCarManuals.com
Remove the thrust washer from the counterbore in the

upper housing.
Remove the square retaining ring from the drive shaft.

Inspect for Reuse

Use a bore cleaning brush and safety solvent. Clean and
inspect the upper housing for damage. Clean and inspect
all oil drillings for debris.
NOTE: Do not remove the 1-inch internal hex pipe plug in
the upper housing near the center drive bore. Do not re-
move the 1/8-inch pipe plug that is on the same housings
located on the engine side of the housing into the right side
outboard hydraulic bushing bore.
Inspect the two rear gear train upper housing dowel pins
in the top of the lower housing. Any damaged dowels must
be replaced.
Use dowel pin remover, Part No. ST-1134, to remove the
dowel pins. Use a brass or lead hammer to install the dowel
pins.
ProCarManuals.com
Measure the thickness of the gasket used on the rear gear

train upper housing.
Refer to the following table for the part number and di-
mension.
Upper to Lower Housing Gasket Thickness —

Nominal (New*)
mm in
Part No. 205723 0.38 NOMINAL 0.015
Part No. 3077231 0.51 NOMINAL 0.020
Part No. 3201852 0.76 NOMINAL 0.030
NOTE: * Used gaskets measure thinner.
Clean and check the center gear for damage.

Check the gear teeth for excessive fretting. Check the
internal splines for wear.
Check the center drive shaft. Check the external splines for
wear.
Inspect the bushing diameters on the shaft for wear. If a

fingernail will catch on scratches or grooves, replace the
shaft.
Measure the shaft of the bushing diameters.
Center Drive Shaft Bushing I.D.

mm in
47.536 MIN 1.8715
47.549 MAX 1.8720
ProCarManuals.com
NOTE: If the bushing does not meet the specifications, the

bushing must be replaced.
Inspect the thrust bearings.

Measure the thrust bearing thickness.
Upper Housing Thrust Bearing Thickness

mm in
2.27 MIN 0.085
2.31 MAX 0.091
NOTE: If the thrust bearings do not meet the specifica-
tions, the bearings must be replaced.
Check the retaining rings for damage.
Check the spacer bearing for damage.
Inspect the three hydraulic pump support bushings in the

upper housing. If a fingernail will catch on scratches or
grooves, replace the bushing.
Measure the bushing inside diameter.
Hydraulic Drive Housing Bushing I.D.

mm in
47.60 MIN 1.874
47.68 MAX 1.877
If the bushing does not meet the specifications, the bush-
ing must be replaced.
Inspect the hydraulic pump support bushing in the shaft

support plate. If a fingernail will catch on the scratches or
grooves, replace the bushing.
Measure the bushing inside diameter.
Hydraulic Pump Support Bushing I.D.

mm in
47.60 MIN 1.874
47.68 MAX 1.877
If the bushing does not meet the specifications, the bush-
ing must be replaced. Refer to Procedure No. 009–037.
Assemble
Use LubriplateT 105 or equivalent. Lubricate the center
hydraulic shaft bushing, two thrust bearings, and the two
counterbores next to the center bushing in the housing.
Install the two thrust bearings with the grooved side facing
away from the housing into the counterbore.
ProCarManuals.com
Install the non-tapered retaining ring onto the center drive

shaft on the end closest to the external splines.
Use LubriplateT 105 or equivalent. Lubricate the pump side

bushing surface on the center drive shaft, the external
splines on the drive shaft, and the internal splines on the
gear. Align the gear in the housing.
Install the shaft into the housing and gear from the engine
side of the upper housing.
Install the bearing spacers and tapered retaining ring with

the beveled side facing the pump side of the drive shaft.
Use LubriplateT 105 or equivalent. Lubricate the engine

side bushing surface on the center hydraulic pump drive
shaft and the bushing in the hydraulic pump drive shaft and
the bushing in the hydraulic pump drive shaft.
Use clean engine oil to lubricate the o-ring. Install the o-ring
into the groove on the support.
Install the hydraulic pump support. Install the four
5/16–18x3/4 inch capscrews. Tighten the capscrews.
ProCarManuals.com
Use a dial indicator.

Center Drive End Clearance

mm in
0.10 MIN 0.004
0.51 MAX 0.020
Install the hydraulic pump adapter or cover plate and gas-

ket. Install the four capscrews.
Tighten the adapter or cover plate to the correct torque.
Torque Value:
Adapter 95 N•m [70 ft-lb]
Cover Plate
SAE C/SAE B
Drive 95 N•m [70 ft-lb]
Cover Plate
SAE A Drive 40 N•m [35 ft-lb]
Use LubriplateT 105 or equivalent. Lubricate the outer hy-

draulic pump support bushings in the upper housing. Lu-
bricate the bushing surfaces on both shafts in the outer

Use a gasket adhesive sparingly. Install the hydraulic sup-
ProCarManuals.com

3/8-16x1-1/4 inch capscrew.
CAUTION
component.
Use three 7/16-14x4 inch guide studs. Install one outer
Use a dial indicator. Make sure the outer hydraulic drive

shaft will not move. Measure the center drive gear to the
outer drive gear backlash.
Center Drive Gear to Outer Drive Gear Backlash

mm in
0.10 MIN 0.004
0.51 MAX 0.020
NOTE: If the gear lash is above the specifications, one or
both of the gears must be replaced.
Remove the four capscrews and outer hydraulic drive

assembly.
ProCarManuals.com
Use three 7/16–14x4 inch guide studs. Install one outer

hydraulic pump support drive assembly. Tighten the
capscrews.
Use a dial indicator. Make sure the outer hydraulic drive

shaft will not move. Measure the center drive gear to the
outer drive gear backlash.
Center Drive Gear to Outer Drive Gear Backlash

mm in
0.10 MIN 0.004
0.51 MAX 0.020
NOTE: If the gear lash is above the specifications, one or
both of the gears must be replaced.
Install four capscrews. Hand tighten the capscrews. Re-

move the guide studs.
Install the remaining three capscrews.
Use the sequence and tighten as shown.
Use the same procedures to install the other hydraulic drive

assembly. Install the assembly.
ProCarManuals.com
The water pump drive is mounted on the front gear housing. It is connected to the water pump with a spline coupling.
A pulley on the end of the water pump drive shaft provides power to the vehicle alternator with a belt.
There is a bushing in the front gear cover at the front of the water pump drive shaft. There are two bushings in the
drive support at the rear of the drive shaft. It is not necessary to machine the bushings in the support when replacement
is required.
Oil is supplied to the bushings in the support through a drilling in the support. Some of the oil that enters the bushing
area lubricates the spline coupling through a hole in the shaft. There must be an orifice plug in the splined end of the
shaft to prevent excessive oil from entering the spline coupling. The oil drilling must have an expansion plug that has
an orifice to prevent excessive oil from being transmitted to the water pump bearings. The expansion plug is located
on the water pump end of the drive.
CAUTION
A pulley pusher must be used to install the alternator drive pulley. Do not use a hammer. If a hammer is used
to install the pulley, the water pump drive gear will move on the shaft and excessive clearance in the drive will
result. Excessive clearance will cause the thrust bearings to fall out and cause the drive to fail.
ProCarManuals.com
Exploded View
ProCarManuals.com
1. Plug, Protective
2. Pulley, Alternator Drive
3. Gear, Water Pump and Alternator Drive
4. Shaft, Water Pump and Alternator Drive
5. Gasket, Water Pump Support
6. Bearing, Thrust
7. Bushing, Water Pump Drive
8. Support, Water Pump
9. Retainer
10. Plug, Pipe
Inspect for Reuse

Measure the water pump drive end clearance.
Water Pump Drive End Clearance

mm in
0.23 MIN 0.009
0.33 MAX 0.013
If the end clearance is not within specifications, replace or
rebuild the assembly.
NOTE: Oversize thrust bearings are available to adjust the
end clearance.
Inspect the water pump drive bushing in the front cover for
excessive wear or damage.
ProCarManuals.com
Inspect the alternator drive pulley for reuse. Refer to Pro-

cedure 009-004.
Inspect the water pump for reuse. Refer to Procedure
008-062.
Disassemble
Use a press to remove the gear from the shaft. Support the
housing and press the shaft downwards
Remove the gear and front thrust bearing.

Remove the pipe plug from the water pump support
housing.
Remove the shaft and rear thrust bearing.

Check the water pump support for an orifice expansion
plug (A). Check the shaft for an orifice pipe plug (B). The
plugs must be removed to clean the oil drillings if dirt or
debris is found in the main oil passage. Do not remove the
plugs if the main oil passage is clean.
ProCarManuals.com
Assemble
If the pipe plug with an orifice was removed, use a driver
to install the plug (A). The plug must be inserted below the
surface of the support housing.
If the orifice pipe plug (B) was removed, install the plug in
the shaft.
CAUTION
The rear thrust bearing MUST be installed with the oil
grooves TOWARD the shaft retainer. Failure will result
if the bearing is NOT installed correctly.
Lubricate the oil groove surface of the rear thrust bearing
with LubriplateT No. 105 or equivalent. Install the bearing
on the shaft with the grooved surface against the shaft
retainer.
Lubricate both the shaft and the water pump support bush-
ings.
Insert the shaft and rear thrust washer into the water pump
support housing.
Water Pump Drive Gear and Shaft (009-031)
CAUTION
The front thrust bearing MUST be installed with the oil
grooves TOWARD the gear. Failure will result if the bear-
ing is NOT installed correctly.
Lubricate the oil groove surface of the front thrust bearing
with LubriplateT No. 105 or equivalent. Install the bearing
onto the housing with the grooved surface against the gear.
Support the housing and shaft assembly in a hydraulic

press.
Clean any LubriplateT from the shaft and apply an even
coating of LoctiteT 609 or equivalent to the inside diameter
of the gear.
Press the gear onto the shaft until the gear touches the
shoulder of the shaft.
ProCarManuals.com
Use a dial indicator. Measure the clearance.
Water Pump Drive End Clearance

mm in
0.23 MIN 0.009
0.33 MAX 0.013
If the end clearance is not within specifications, check to
be sure that both thrust bearings are correctly positioned
in the water pump support counterbores.
If the bearings are correct and the end clearance is not
within specifications, the drive must be completely disas-
sembled and the components dimensions checked.
Oversize thrust bearings are available to adjust the end
clearance.
Water Pump Drive Gear and Shaft

(009-031)
Disassemble
NOTE: The gear should be removed from the shaft ONLY
when the gear or the shaft must be replaced.
Support the gear with the oil hole positioned as shown.
Use an arbor press to remove the gear.
Water Pump Drive Bushing (009-030)
Assemble
Use LoctiteT 609 or equivalent. Apply a smooth coating on
the I.D. of the gear.
Support the gear.
Use an arbor press to press the shaft in the gear until it
touches the shoulder of the shaft.
Water Pump Drive Bushing (009-030)

Disassemble
Use an arbor press and a mandrel to remove the bushings.
ProCarManuals.com
Assemble
CAUTION
Do not block the oil drilling in the housing.
Use an arbor press and a mandrel to install the bushings.
The bushings must be even with to a maximum of 0.38 mm
[0.015 inch] below the housing surface.
Water Pump Drive Pulley (009-032)

Clean
Use solvent to clean the alternator drive and the accessory
drive pulley.
Outer Hydraulic Pump Support Drive (009-036)
Inspect for Reuse

Check the grooves of the pulley for wear.
Check the wear sleeve on the accessory drive pulley.
If the wear sleeve needs replaced, use a chisel and remove
the wear sleeve.
Check the Pulley O.D. for damage.
Use an arbor press and a mandrel to install the new wear
sleeve even with the end of the pulley.
Outer Hydraulic Pump Support Drive

(009-036)
Disassemble
Remove the hydraulic pump adapter and/or cover plate.
Remove and discard the gasket
ProCarManuals.com
Remove the tapered retaining ring, bearing spacer, and

thrust bearing. Check bearing spacer for wear against the
shaft shoulder.
Remove the hydraulic pump support from the splined drive

shaft.
Remove the thrust bearing, gear, and non-tapered retain-

ing ring from the splined drive shaft.
Inspect for Reuse

Visually inspect the idler gear for chipped, broken, or
cracked teeth. Check the internal splines for wear.
ProCarManuals.com
Check the hydraulic pump drive shaft. Check the external

splines for wear.
Inspect the bushing diameters on the shaft for wear. If a

fingernail will catch on scratches or grooves, then the shaft
must be replaced. Measure the shaft in the bushing area.
Drive Shaft Bushing Diameters

mm in
47.536 MIN 1.8715
47.549 MAX 1.8720
Clean and inspect the thrust bearings. Measure the thrust

bearing thickness.

mm in
2.27 MIN 0.085
2.31 MAX 0.091
Check the retaining rings for damage.

Inspect the hydraulic pump support bushing. If a fingernail
will catch on scratches or grooves, then the bushing must
be replaced. Measure the bushing inside diameter.
Hydraulic Pump Support Bushing I.D.

mm in
47.60 MIN 1.874
47.68 MAX 1.877
ProCarManuals.com
Install
Install the four capscrews and hand tighten the capscrews.
Install the remaining three capscrews.
Use the sequence and torque as shown.
NOTE: The backlash is to be measured during rebuild.
Use the same procedures to install the other outer hydrau-

lic drive assembly. Install the assembly.
Assemble
Install the non-tapered snap ring onto the drive shaft.
Use LubriplateT 105 or equivalent. Lubricate the external
splines on the drive shaft and the internal splines on the
gear.
Align and install the gear onto the drive shaft.
Use LubriplateT 105 or equivalent. Lubricate the hydraulic

pump support bushing, counterbore, and one thrust bear-
ing.
Place the thrust bearing with the groove side up into the
counterbore of the cone shaped end of the hydraulic pump
support.
ProCarManuals.com
Place the gear and shaft assembly on end with the gear
end down. Align and install the hydraulic pump support
cone end first onto the drive shaft and gear assembly.
Use LubriplateT 105 or equivalent. Lubricate one thrust

bearing. Install the thrust bearing into the counterbore of
the hydraulic pump support with groove side up.
Hydraulic Pump Support Bushing (009-037)
With the beveled side up, install the bearing spacer over
the drive shaft.
With the beveled side up, install the tapered retaining ring
into the groove on the drive shaft.
Measure the gear end clearance.
Hydraulic Drive Gear End Clearance

mm in
0.10 MIN 0.004
0.51 MAX 0.020
ProCarManuals.com
Install the hydraulic pump adapter or cover plate and gas-

ket. Tighten the adapter or cover plate to the correct torque.
Torque Value:
Adapter 95 N•m [70 ft-lb]
Torque Value:
Cover Plate SAE
C/SAE
B drive 95 N•m [70 ft-lb]
SAE A drive
40 N•m [35 ft-lb]
Hydraulic Pump Support Bushing

(009-037)
Remove
Use a blind bushing puller to remove the bushing.
Inspect for Reuse

Measure the bushing bore.
Hydraulic Pump Support Bore I.D.

mm in
53.86 MIN 2.121
53.92 MAX 2.123
NOTE: If the bushing bore is not within specifications,
replace the support.
Install
Use an appropriate bushing mandrel and a press. Install
the bushing flush with the support or no more than 5.08
mm [0.200 in] below the surface.
ProCarManuals.com
Measure the bushing inside diameter again.
Hydraulic Pump Support Bushing Bore I.D.

mm in
47.60 MIN 1.874
47.68 MAX 1.877
NOTE: If the bushing is not within specifications, replace
the support.
Section 10 - Air Intake System - Group 10 Page 10-a
Section 10 - Air Intake System - Group 10

Section Contents
Page
Aftercooler Assembly .................................................................................................................................... 10-3
Assemble .................................................................................................................................................... 10-5
Clean ......................................................................................................................................................... 10-4
Disassemble ............................................................................................................................................... 10-4
Exploded View............................................................................................................................................. 10-3
Aftercooler Coolant Tube ............................................................................................................................... 10-6
Clean ......................................................................................................................................................... 10-6
Air Crossover ................................................................................................................................................. 10-7
Clean ......................................................................................................................................................... 10-7
Air Intake System - General Information ....................................................................................................... 10-1
Preparatory ................................................................................................................................................. 10-1
Charge Air Cooler (CAC) ................................................................................................................................ 10-8
Clean ......................................................................................................................................................... 10-8
Leak Test .................................................................................................................................................... 10-9
ProCarManuals.com
Service Tools.................................................................................................................................................. 10-2

Air Intake System......................................................................................................................................... 10-2
Turbocharger Heat Shield............................................................................................................................. 10-11
Clean ........................................................................................................................................................ 10-11
Marine Applications ............................................................................................................................... 10-11
Inspect for Reuse ...................................................................................................................................... 10-11
Install ........................................................................................................................................................ 10-11
Remove .................................................................................................................................................... 10-11
Turbocharger, Water-Cooled......................................................................................................................... 10-10
Clean ........................................................................................................................................................ 10-10
Inspect for Reuse ...................................................................................................................................... 10-10
Air Intake System - General Information
Section 10 - Air Intake System - Group 10 Page 10-1
Air Intake System - General Informa-

tion
Preparatory
The combustion air system consists of air intake system,
turbocharger (A), air crossover (C), and aftercooler assem-
bly (D).
The aftercooler assembly (or intake manifold) to cylinder
head mounting capscrews are covered by rubber sleeves.
The rubber sleeves are located on the top mounting
capscrews at the cylinder head. These sleeves prevent
capscrew damage by keeping dirt and water off of the
threads. These sleeves must be replaced during rebuild.
All QSK19 engines have turbochargers. The turbochargers

also have water cooled bearing housings. This gives the
turbocharger increased working life by reducing the harm
of hot shutdowns.
The turbocharger uses exhaust gas energy to turn the
turbine wheel. This turbine wheel drives a compressor
impeller that provides pressurized air to the engine for
combustion.
ProCarManuals.com
QSK19 engines can have either JWAC (jacket water after

cooled) air cooling systems, or LTA (low temperature after-
cooling) air cooling systems. These systems use engine
coolant to cool the inlet air between the turbocharger and
the engine. Refer to the coolant flow diagrams.
Rail Applications
Because the QSK19 Rail engine uses an air-to-air after-
cooler, there is no aftercooler element in the intake mani-
fold that uses coolant to cool the intake air. The intake
housing is a one-piece component that contains an inlet
duct. This air-to-air aftercooler has a turbocharger outlet
elbow which is unique to all QSK19 air-to-air cooled engines.
Service Tools
Page 10-2 Section 10 - Air Intake System - Group 10
Service Tools
Air Intake System

Manometer
Used to measure air inlet restriction.
ST-1111-3
ProCarManuals.com
Dial depth gauge

Used to check for proper nozzle ring crush or end clearance
checks on turbochargers.
ST-537
Aftercooler Assembly (010-002)

Exploded View
ProCarManuals.com
1. Gasket, Intake Manifold 15. Screw, Captive Washer Cap

2. Seal, Grommet 16. Gasket, Exhaust Manifold
3. Retainer, Seal 17. Screw, Hex Flange Head Cap
4. Gasket, Connection 18. Spacer, Mounting
5. Screw, Captive Washer Cap 19. Gasket, Aftercooler Housing
6. Seal, Rectangular Ring 20. Gasket, Aftercooler Cover
7. Screw, Captive Washer Cap 21. Screw, hexagon Head Cap
8. Seal, O-ring 22. Manifold, Exhaust
9. Plug, Threaded 23. Connection, Air Crossover
10. Plug, Threaded 24. Cover, Aftercooler
11. Seal, O-ring 25. Manifold, Exhaust
12. Screw, Captive Washer Cap 26. Core, Aftercooler
13. Screw, Captive Washer Cap 27. Housing, Aftercooler
14. Washer, Plain
Clean
WARNING
personal injury.
Use solvent to clean the exterior of the aftercooler assem-
bly.
NOTE: Use a solvent that will not harm copper.
Use solvent to clean the elements.
Inspect for Reuse

Inspect the aftercooler for reuse. Look into the cylinder
head ports and into the aftercooler for indications of coolant
leakage.
ProCarManuals.com
Use a hose with a plugged with a pipe plug to plug one

water tube as shown.
Attach an air line and gauge to the remaining tube.
Pressure check the element.
Apply air pressure and check for leaks.
Air Pressure
kPa psi
415 MAX 60
NOTE: Heating the tank water to 50°C (120°F) will improve
the test results.
Disassemble
Remove the capscrews, seal retainer (3), gaskets (4), and
seals (5). Discard the seals and gaskets.
Remove the aftercooler cover capscrews and cover.
Remove the element and gaskets.

Inspect the cover and intake manifold gasket surfaces for
damage.
Inspect the threaded holes for damage.
ProCarManuals.com
Assemble
Install the element and two new gaskets.
Install the aftercooler cover and capscrews.

Do not tighten the capscrews until after the seals are
installed.
Aftercooler Coolant Tube (010-006)
Use engine oil to lubricate the seals.

Install the seal on the retainer.
Use clean engine oil to lubricate the O.D. of the water
bosses on the aftercooer element.
Slide the gasket on the water bosses. Slide the seal and
retainer on the tube.
Install the capscrews, and tighten.
Install the 24 capscrews.

Tighten using the following steps and values.
Torque Value:
ProCarManuals.com
Aftercooler Coolant Tube (010-006)

Clean
WARNING
personal injury.
Use solvent to clean the aftercooler water inlet and outlet
tubes.
Dry with solvent.
Use a wire brush to clean the hose sealing surfaces.
Inspect for Reuse

Inspect the aftercooler water tubes for damage.
Air Crossover (010-019)
Air Crossover (010-019)

Clean
WARNING
personal injury.
Use solvent to clean the air crossover.
Use compressed air to dry the air crossover.
Marine
WARNING
personal injury.
ProCarManuals.com
Use compressed air to dry the parts.
Inspect for Reuse

Inspect the air crossover for cracks, breaks, holes, and
worn bolt holes.
Marine
NOTE: The Marine air crossover hose (3) is a different
material hose than the standard QSK19 hose.
Inspect the crossover tube for cracks.
Inspect the bore for any blockage.
Inspect the o-ring grove on the mounting flange and the
hose clamps (4) for any wear or damage.
Charge Air Cooler (CAC) (010-027)

Clean
If the engine experiences a turbocharger failure or any
other occasion where oil or debris is put into the CAC,
(charge air cooler) the CAC must be cleaned.
Remove the CAC piping and CAC from the vehicle. Refer
to the manufacturer’s instructions.
CAUTION
Do not use caustic cleaners to clean the CAC. Damage
to the CAC will result.
Flush the CAC internally with solvent in the opposite di-
rection of normal air flow. Shake the CAC and lightly tap
on the end tanks with a rubber mallet to dislodge trapped
debris. Continue flushing until all debris or oil is removed.
ProCarManuals.com
NOTE: Be sure the tubes are in the vertical direction when

flushing.
If the debris cannot be totally removed from the CAC, the
CAC must be replaced.
CAUTION
The CAC must be rinsed, dried and free of solvent, oil
and debris or engine damage will result.
After the CAC has been thoroughly cleaned of all oil and
debris with solvent, wash the CAC internally with hot soapy
water to remove the remaining solvent. Rinse thoroughly
with clean water.
Blow compressed air through the inside of the CAC in the
opposite direction of normal air flow until the CAC is dry
internally.
Inspect for Reuse

Visually inspect the CAC for cracks, holes or damage.
Inspect the tubes, the fins and the welds for tears, breaks
or other damage. If any damage causes the CAC to fail the
air leak check, the CAC must be replaced.
NOTE: Always clean and inspect the CAC piping and hoses
prior to installation.
Leak Test
WARNING
To prevent possible injury if either plug blows off during
the test, secure safety chains on the test plugs to any
convenient capscrew on the radiator assembly. This
test must not be performed without securely fastened
safety chains.
To check the CAC for cracked tubes or header, remove the
inlet and outlet hoses from the cooler. The CAC does not
have to be removed from the chassis.
Install a plug or cap over the outlet side of the cooler. Install
a pressure gauge and a regulated shop air supply line with
a shutoff valve to the inlet side of the cooler.
Apply air pressure to the cooler until the pressure gauge

reads a steady 207 kPa [30 psi] of air pressure.
Shut off the air flow to the cooler and start a stopwatch at
the same time. Record the leakage at 15 seconds.
If the pressure drop is 34 kPa [5 psi] or less in 15 seconds,
the cooler is okay.
If the pressure drop exceeds 34 kPa [5 psi] in 15 seconds,
ProCarManuals.com
check all connections again.
Determine if the pressure drop is caused by a leak in the

CAC or from a leaky connection. Use a spray bottle filled
with soapy water applied to all hose connections, and watch
for bubbles to appear at the location of the leak.
If the pressure drop is caused by a leaky connection, repair
the connection and repeat the test. If the leak is within the
CAC, repeat the test to verify the accuracy of the pressure
drop measurement. Similar pressure drop readings must
be obtained at least three consecutive tests before the
reading can be considered accurate.
NOTE: If a CAC leaks more than 34 kPa [5 psi] in 15
seconds, it will appear as a major leak in a leak tank.
If the pressure drop is greater than 34 kPa [5 psi] in 15

seconds, the CAC must be replaced.
Refer to the manufacturer’s repair manual for replacement
instructions.
NOTE: Charge air coolers are not designed to be 100%
leak free. If the pressure drop is less than 34 kPa [5 psi] in
15 seconds, then the CAC does not need to be replaced.
Turbocharger, Water-Cooled (010-037)

Clean
WARNING
personal injury.
CAUTION
Tape or plug all openings to prevent solvent or steam
from entering the oil cavities in the turbocharger.
Use steam to clean the turbocharger.
Inspect for Reuse

Check the exterior of the turbocharger for damage.
Check the wheel for fretting and broken vanes.
Use a dial indicator to measure the turbocharger end clear-
ance.
ProCarManuals.com
Turbocharger End Clearance

mm in
0.05 MIN 0.002
0.13 MAX 0.005
NOTE: If the end clearance exceeds the specifications, the
turbocharger must be replaced or rebuilt. Refer to the
Turbocharger Service Repair Manual, Bulletin No. 3580999,
for rebuild instructions.
Use your hand to push the impeller end of the shaft toward
the housing.
Use a wire type gauge to measure the clearance between
the impeller and the housing at the minimum clearance
point.
Holset HX82 Turbocharger

mm in
Compressor Impeller 0.15 MIN 0.006
0.45 MAX 0.018
Turbine Wheel 0.20 MIN 0.008
0.55 MAX 0.210
NOTE: If the clearance exceeds the specifications, the
turbocharger must be replaced or rebuilt. Refer to the
Turbocharger Service Repair Manual, Bulletin No. 3580999,
for rebuild instructions.
Turbocharger Heat Shield (010-076)

Remove
Marine Applications
CAUTION
Do not remove insulation from inside of turbocharger
heat shield. Insulation is permanently affixed to the
heat shield.
Remove the turbocharger heat shield mounting capscrews.
Remove the turbocharger heat shield.
Clean
Marine Applications
WARNING
personal injury.
ProCarManuals.com
Use solvent to clean the turbocharger heat shield.

NOTE: Take care not to damage the turbocharger heat
shield insulation.
Inspect for Reuse

Marine Applications
Inspect the turbocharger heat shield for cracks, holes, and
damaged bolt holes.
Install
Marine Applications
Install the turbocharger heat shield.
Install and tighten the turbocharger heat shield mounting
capscrews.
NOTES
ProCarManuals.com
Section 11 - Exhaust System - Group 11 Page 11-a
Section 11 - Exhaust System - Group 11

Section Contents
Page
Exhaust Manifold, Dry .................................................................................................................................... 11-1
Assemble .................................................................................................................................................... 11-3
Clean .......................................................................................................................................................... 11-1
Marine Applications ................................................................................................................................ 11-2
Disassemble ............................................................................................................................................... 11-2
Marine Applications ................................................................................................................................ 11-3
Exhaust Manifold Heat Shield........................................................................................................................ 11-3
Clean .......................................................................................................................................................... 11-3
Exhaust System - General Information .......................................................................................................... 11-1
ProCarManuals.com
Exhaust System - General Information
Section 11 - Exhaust System - Group 11 Page 11-1
Exhaust System - General Information

General Information
This section covers ONLY those repairs to the exhaust
manifold.
Please refer muffler and exhaust pipe repairs to the original
equipment manufacturer.
The exhaust system consists of the exhaust manifold and
exhaust piping.
NOTE: There is no exploded view pertaining to this section.
Rail Applications
The QSK19 Rail engine exhaust center section has been
changed to accommodate the angle of the exhaust transfer
connection. The exhaust transfer connection allows the
turbocharger to be extended above and over the rocker
covers to maintain a low profile design needed in a railcar
application. The exhaust transfer connection has two sup-
porting brackets that mount to the No. 2 and No. 3 rocker
lever housings
ProCarManuals.com
Rail Applications
The two capscrews and spacers for the upper inside
capscrew locations on the exhaust center section of the
exhaust manifold have been shortened to make it possible
to get a wrench on the capscrew heads.
During installation, apply an antiseize compound on the
capscrews threads.
Exhaust Manifold, Dry (011-007)

Clean
WARNING
When using solvents, acids, or alkaline material or
steam for cleaning, follow the manufacturer’s recom-
mendations for use. Wear goggles and protective cloth-
ing to avoid personal injury.
Use solvent to clean the manifold.
Use a wire brush to clean the sealing joints inside and
outside diameters to remove any scale that has
accumulated.
Page 11-2 Section 11 - Exhaust System - Group 11
Use a 240 grit emery cloth to clean all of the exhaust

manifold gasket surfaces.
Marine Applications
WARNING
for use. Wear goggles and protective clothing.
CAUTION
Care must be taken to not destroy the exhaust manifold
ProCarManuals.com
heat shield insulation while cleaning.

Use solvent to clean the marine exhaust manifold.
Disassemble
Use a mallet to remove the end sections from the exhaust
manifold center section.
Inspect for Reuse

Inspect for cracks in the areas shown.
Exhaust Manifold Heat Shield (011-015)
Section 11 - Exhaust System - Group 11 Page 11-3
Inspect the capscrew holes in the center section for dam-

age.
NOTE: The manifold has been subjected to high tempera-
tures if the capscrew threads are visible on the side of the
capscrew holes. High temperature can cause the manifold
to shrink.
Measure the center-to-center distance between the same
position capscrew holes of the two flanges on the center
section and both end sections to determine if the manifold
is too short.
Exhaust Manifold Capscrew Holes

mm in
191.5 MIN 7.54
193.5 MAX 7.62
Marine Applications
NOTE: Exhaust leaks will show as black soot on the insu-
lation.
Inspect the heat shield insulation for signs of exhaust leaks.
If exhaust leaks in the manifold are found, the exhaust
manifold must be replaced.
ProCarManuals.com
Assemble
Use an anti-seize compound to lubricate the O.D. of the end
section in the area that slides into the center section.
Use a mallet and drive the end section into the center
section.
Exhaust Manifold Heat Shield

(011-015)
Clean
WARNING
When using solvents, acids, or alkaline material for
personal injury.
Use solvent to clean the exhaust manifold heat shield.
Exhaust Manifold Heat Shield (011-015)
Page 11-4 Section 11 - Exhaust System - Group 11
Inspect for Reuse

Inspect the heat shield for any cracks or damage.
ProCarManuals.com
Section 12 - Compressed Air System - Group 12 Page 12-a
Section 12 - Compressed Air System - Group 12

Section Contents
Page
Compressed Air System - General Information ............................................................................................ 12-1
ProCarManuals.com
Compressed Air System - General Information
Section 12 - Compressed Air System - Group 12 Page 12-1
Compressed Air System - General

Information
General Information
The compressed air system normally consists of a gear-
driven air compressor, an air governor, air tanks and all
necessary plumbing.
The Holset and Cummins single and two cylinder air com-
pressors are engine-driven, piston-type compressors which
supply compressed air to operate air activated devices.
The compressor runs continuously, but has a loaded and
unloaded operating mode.
E-Type Air Compressor

Holset SS and ST model air compressors built with the
E-Type unloader can be identified by the letter “E” (SS296E,
SS338E, ST676E, and ST773E), and by the caution on the
data plate.
All QE (QE296 and QE338) model air compressors are
equipped with the E-Type unloader.
ProCarManuals.com
E-Type System With Air Dryer

Vehicles equipped with air dryers vented to the atmosphere
during unloaded compressor operation, using the Holset
E-Type air compressor, require the installation of an econ
valve to prevent excessive oil consumption.
NOTE: Some air dryers can have a built-in econ valve.
Check with the manufacturer as to which type is installed.
E-Type System Without Air Dryer

Air systems without air dryers, or with air dryers not vented
to the atmosphere during unloaded compressor operation,
can use the Holset E-Type unloader valve without modify-
ing the air system.
Compressed Air System - General Information
Page 12-2 Section 12 - Compressed Air System - Group 12
ProCarManuals.com
Typical Schematic for Twin Cylinder Air Compressor
1. Engine air filter 10. 2500 cubic inch receiver tank

2. Engine 11. Heated spitter valve
3. Turbocharger 12. 1206.6 kPa [175 psig] safety valve
4. Holset ST compressor 13. 2 CR Turbo 2000 air filters
5. Optional turbo inlet 14. Air dryer governor
6. Center unloader valve (std) 15. Supply tank
7. Compressor governor 16. Spitter valve
8. Exhaust line from compressor to receiver tank is 17. 18 scfm maximum system use
a minimum 457.2 cm [15 ft] of 1 in. nominal 18. Governor RES port
9. Line from governor RES port to receiver tank - 19. Governor unload port
minimum 1/4 in. nominal ID 20. 3/4 in. nominal line
Section 13 - Electrical Equipment - Group 13 Page 13-a
Section 13 - Electrical Equipment - Group 13

Section Contents
Page
Alternator Adjusting Link .............................................................................................................................. 13-4
Clean ......................................................................................................................................................... 13-4
Alternator Bracket.......................................................................................................................................... 13-2
Clean ......................................................................................................................................................... 13-2
Drive Belt, Alternator ..................................................................................................................................... 13-2
Adjust ......................................................................................................................................................... 13-2
Electrical Equipment - General Information .................................................................................................. 13-1
Starting Motor ................................................................................................................................................ 13-3
Clean ......................................................................................................................................................... 13-3
ProCarManuals.com
Electrical Equipment - General Information
Section 13 - Electrical Equipment - Group 13 Page 13-1
Electrical Equipment - General

Information
General Information
The basic heavy-duty electrical system consists of:
• Batteries (1)
— (Usually two or four connected in parallel)
• Starting motor (2)
• Alternator (3)
• Magnetic switch (4)
• Ignition switch (5)
• Necessary wiring
All components must be carefully matched.
The accompanying illustrations show typical parallel and

series battery connections.
• Parallel connection
ProCarManuals.com
• Series connection
Alternator Bracket (013-003)
Page 13-2 Section 13 - Electrical Equipment - Group 13
Alternator Bracket (013-003)

Clean
WARNING
personal injury.
Inspect for Reuse

Check the threads for damage.
Check for cracks.
Check the bores for wear.
NOTE: If any of the above conditions are found, the bracket
must be replaced.
ProCarManuals.com
Drive Belt, Alternator (013-005)

Adjust
Use the belt tension gauge, Part No. ST-1138 to check the
belt tension.
Belt tension must be:
Alternator Belt Tension 670 N [150 lbf]
Loosen the alternator and adjusting link mounting

capscrews.
Loosen the jam nuts on the adjusting screw.
Starting Motor (013-020)
Section 13 - Electrical Equipment - Group 13 Page 13-3
Turn the adjusting screw clockwise to tighten the belt

tension.

Tighten the jam nuts on the adjusting screw.
Tighten the adjusting link and alternator mounting
capscrews.
Torque Value:
Jam Nuts 55 N•m [40 ft-lb]
Alternator Mounting
ProCarManuals.com
Capscrews 55 N•m [40 ft-lb]
Check the belt tension again to be sure it is correct.

The belt tension must be:
Belt Tension 670 N [150 lbf]
Starting Motor (013-020)

Clean
WARNING
When using steam or hot, high pressure water for clean-
ing, wear goggles and protective clothing to avoid per-
sonal injury.
Use steam to clean the exterior of the starting motor.
Alternator Adjusting Link (013-022)
Page 13-4 Section 13 - Electrical Equipment - Group 13
Inspect for Reuse

Inspect the gear, shaft, and the bushing for wear or dam-
age.
Lubricate the bushing with engine oil.
NOTE: A pipe plug must be removed to lubricate the bush-
ing on some starter motors.
Alternator Adjusting Link (013-022)

Clean
WARNING
personal injury.
ProCarManuals.com
Use solvent to clean the alternator adjusting link.

Inspect for Reuse

Check the threads for damage.
QSK19
Section 14 - Engine Testing - Group 14 Page 14-a
Section 14 - Engine Testing - Group 14

Section Contents
Page
Dynamometer Worksheet............................................................................................................................. 14-10
Worksheet ................................................................................................................................................. 14-10
Engine Run-in (Chassis Dynamometer) ...................................................................................................... 14-23
General Information .................................................................................................................................. 14-23
Engine Throttle Control...................................................................................................................... 14-24
Run-In Instructions ................................................................................................................................... 14-26
Engine Run-in (Engine Dynamometer) ........................................................................................................ 14-42
General Information .................................................................................................................................. 14-42
Engine Run-in (Without Dynamometer) ...................................................................................................... 14-28
Preparatory ............................................................................................................................................... 14-28
General Engine Test Procedures ....................................................................................................... 14-28
Generator Set.................................................................................................................................... 14-30
Off-Highway....................................................................................................................................... 14-30
Engine Testing - General Information............................................................................................................ 14-1
Fuel Flow Measurement on Engine or Chassis Dynamometer .................................................................... 14-2
Installation........................................................................................................................................... 14-2
Operation ............................................................................................................................................ 14-3
ProCarManuals.com

Engine Testing (Chassis Dynamometer) ...................................................................................................... 14-11
Setup ........................................................................................................................................................ 14-11
Test .......................................................................................................................................................... 14-14
Engine Testing (Engine Dynamometer) ....................................................................................................... 14-31
Install ....................................................................................................................................................... 14-31
Test .......................................................................................................................................................... 14-34
Engine Testing (In Chassis) ......................................................................................................................... 14-47
Stall Speed Check .................................................................................................................................... 14-47
Time Speed Check ................................................................................................................................... 14-50
Service Tools.................................................................................................................................................. 14-8
Engine Testing............................................................................................................................................. 14-8
Specifications ................................................................................................................................................ 14-6
Cooling System .......................................................................................................................................... 14-7
Engine Testing ........................................................................................................................................... 14-6
Exhaust System ......................................................................................................................................... 14-7
Lubricating Oil System ............................................................................................................................... 14-7
QSK19 Engine Testing - General Information
Section 14 - Engine Testing - Group 14 Page 14-1
Engine Testing - General Information

General Information
This section outlines engine testing and engine run-in rec-
ommendations for QSK19 engines. All engines must be
run-in after a rebuild or a repair involving the replacement
of one or more piston ring sets, cylinder liners or pistons.
Incorrect or insufficient break-in of the piston rings will
lead to early oil consumption or high blowby complaints.
Adherence to these run-in guidelines will allow the full
durability of new pistons, liners, and rings to be real-
ized.
Before running the engine, make sure the engine is filled
with the proper coolant. Also, make sure the lubricating oil
system is filled and primed.
In-Service Run-In
The following in-service run-in guidelines are recommended
for QSK19 engines after a repair involving replacement of
one or more of the piston ring sets, cylinder liners or pistons
where engine or an engine dynamometer and/or chassis
dynamometer run-in cannot be performed.
ProCarManuals.com
The majority of heavy duty diesel applications will provide

sufficient run-in under normal loaded operations. However,
light load/high rpm operation must be avoided during the
run-in period.
Engine Dynamometer Run-In

This is the preferred method of run-in for engines that have
been rebuilt out-of-chassis. It is not practical, nor recom-
mended that an engine be removed from the application to
conduct the run-in after a rebuild or cylinder repair has
been performed in-chassis. There is no requirement, nor is
it recommended for an engine that has been run-in and
tested on an engine dynamometer to be run-in again after
it has been installed in the vehicle or equipment.
Chassis Dynamometer, Portable Dynamometer or

Load Bank Run-In
When it is not possible to load an engine immediately after
rebuild or repair, (example: on-highway tractor that must be
‘‘bobtailed’’ for delivery, a standby generator or fire pump
that cannot be operated because of customer restrictions,
a fire truck that cannot be loaded with the water pump,
etc.), the engine must be run-in on a chassis dynamometer,
portable dynamometer or load bank following the recom-
mendations outlined in the attached procedures.
Engine Testing - General Information QSK19
Page 14-2 Section 14 - Engine Testing - Group 14
Fuel Flow Measurement on Engine or

Chassis Dynamometer
Accurate fuel flow measurement is important for evaluation
of engine performance and troubleshooting on an engine
or chassis dynamometer. The only way accurate fuel flow
measurement can be obtained is through proper use of
available equipment. Below is a description of the fuel
measuring device, available from Cummins Engine Com-
pany, along with installation and operation recommenda-
tions. The fuel measuring device, Part No. 3376375, can be
used with either a chassis or engine dynamometer.
Installation
When installing the fuel measuring device, it is important
to reduce the amount of air that can be introduced into the
system when the device is not in use. Therefore, the plumb-
ing used must include non-restrictive shutoff valves, such
as ballcock valves, to contain fuel in the device after each
use. Additional installation considerations are:
• The fuel measuring device, Part No. 3376375, must
be mounted vertically to ensure accuracy and proper
operation.
• A separate fuel supply for use on the dynamometer
ProCarManuals.com
is recommended. All fuel used in the measuring

device must be clean for consistent operation.
• Care must be taken to reduce fuel line restriction to
and from the engine. Minimum recommended hose
sizes are No. 10 for the engine fuel inlet, and No. 8
for the engine fuel drain. The length of either hose
must not exceed 15 feet.
• For accurate fuel consumption or flow measurement
while testing on a chassis dynamometer, it is rec-
ommended to use a fuel cooler to maintain inlet
temperature to the fuel gear at 49°C [120°F] or
below.
Operation
This is a schematic of the fuel measuring device, Part No. 3376375. The device consists of the following components:
• Fuel Filter
• Flowmeter
• Float Tank
• Fuel Rail Pressure Gauge
• Fuel Cooler is not a part of fuel measuring device, Part No. 3376375, however it must be used when conducting
test with the flow meter.
ProCarManuals.com
Engine Testing - General Information QSK19
The fuel measuring device recirculates return fuel to the engine fuel inlet by routing the return fuel to the top side of
the float tank. The fuel is deaerated as it passes through the baffling in the float tank. A ball float valve at the bottom
of the float tank maintains an adequate volume in the tank for deaeration. The fuel is then returned to the engine fuel
inlet. Refer to the sketch for fuel line connection points on the fuel measuring device.
1. Fuel Supply from Tank
2. Fuel Flow to Fuel Meter
3. Fuel Flow from Fuel Meter
4. Fuel Flow to Fuel Cooler
5. Injector Return Fuel
6. Fuel Rail Pressure
NOTE: The fuel supply tank must be below the level of the fuel measuring device to prevent overflow of the float tank.
If an overhead fuel supply tank is used, a float controlled reservoir must be installed between the fuel supply tank and
the fuel measuring device, and below the level of the device.
ProCarManuals.com
The fuel measuring device is installed in series between the fuel supply tank and the engine fuel inlet. The quantity
of fuel being drawn through the flowmeter is known as MAKE-UP fuel or the amount of fuel being burned by the engine.
The flowmeter is graduated to read fuel flow in pounds per hour. The flowmeter contains two floats with respective scales
on either side of the flowmeter, The small float is used to measure lower flows and must be read on the left scale, as
shown. The larger float is for measuring higher flows and must be read on the right scale.
To obtain an accurate fuel rate measurement, the flowmeter reading must be corrected based on the fuel temperature.
There is a fuel temperature gauge on the front panel of the fuel measuring device. The gauge is graduated in percent
of error by which the reading requires correction. An example is: The fuel of an engine reads 125 lbs/hr on the flowmeter,
and the temperature gauge reads +2 percent; the corrected fuel flow rate will be 125 plus 2 percent, or 127.5 lbs/hr.
ProCarManuals.com
Specifications
Engine Testing
Maintain the following limits during the engine test/run-in procedures:
Due to variations in ratings of different engine models, refer to the specific ‘‘Engine Data Sheet’’ for the particular engine
model being tested.
Intake Restriction (Maximum at Advertised Horsepower)
•Clean Air Filter ......................................................................................................... 381 mm H20 [15 in. H2O]
•Dirty Air Filter .......................................................................................................... 635 mm H20 [25 in. H2O]
Exhaust Back Pressure (Maximum at Advertised Horsepower) .............................................. 75 mm Hg [3 in. Hg]
Blowby* (Maximum at Advertised Horsepower)
• New or rebuilt engines
(Maximum) (Less than 160,000 km [100,000 miles] or 3600 hours) .................................................. See Tables
•Used Engines
(Maximum) (Over 160,000 km [100,000 miles] or 3600 hours) .......................................................... See Tables
Oil Pressure (With 15W-40 oil at 107°C [225°F])
• Low Idle (Minimum Allowable) ............................................................................................... 138 kPa [20 psi]
•At 1200 RPM or Torque Peak (Minimum allowable) ................................................................ 207 kPa [30 psi]
Fuel Inlet Restriction measured at fuel pump inlet (Maximum at Advertised Horsepower)
• Clean Fuel Filter ................................................................................................................. 102 mm [4 in Hg]
•Dirty Fuel Filter .................................................................................................................... 203 mm [8 in Hg]
ProCarManuals.com
•Maximum Allowable Fuel Inlet Temperature ................................................................................ 71°C [160°F]

*Blowby checking tools, Part No. 3822566 - 0.302 inch orifice, Part No. 3823567 - 0.354 inch orifice, and Part No.
3822568 - 0.406 inch orifice, have a special orifice that must be used to be certain an accurate reading is obtained.
QSK19 Blowby Limits
(using 0.302 inch diameter orifice at rated load and speed)
Engine HP (RPM Rating) New/Rebuilt Used Engine Limit
699 HP and Below 305 mm H2O 762 mm H2O
(1500 - 1900) [12 in H2O] [30 in H2O]
(2000 and above) [14 in H2O] [35 in H2O]
700 HP and Above 508 mm H2O 1270 mm H2O
[20 in H2O] [50 in H2O]
QSK19 Blowby Limits

(1500 - 1900) [7 in H2O] [18 in H2O]
699 HP and Below 203 H2O 508 mm H2O
[9 in H2O] [23 in H2O]
QSK19 Blowby Limits

All Ratings 127 mm H2O 330 mm H2O
[5 in H2O] [13 in H2O]

Oil Pressure (With 15W-40 Oil at 107° C [225° F])
At Idle (Minimum Allowable) .................................................................................................... 138 kPa [20 psi]
At No Load Governed Speed ............................................................................... 345 to 483 kPa [50 to 70 psi]
Oil Temperature
Maximum ................................................................................................................................. 120°C [250° F]
Oil Filter Capacity
Bypass Filter (Spin-On)(LF777 Fleetguard) ............................................................ 2.3 Liters [0.6 U.S. Gallons]
Full-Flow Filter (Spin-On)(LF670 Fleetguard) .......................................................... 2.7 Liters [0.7 U.S. Gallons]
Combination Filter (Two LF3000 Fleetguard) .......................................................... 5.7 Liters [1.5 U.S. Gallons]
Oil Pan Capacity (Liters) [U.S. Gallons]
Oil Pan Part No. High Low High Low
3096460 72 64 19 17
3086096 61 49 16 13
3086097 61 49 16 13
3331695 61 49 16 13
3331568 114 102 30 27
NOTE: When the rear gear train option is specified, add 7.6 liters [2 U.S. gallons] to the oil pan capacity listed above.
ProCarManuals.com
Cooling System
Coolant Capacity (Engine Only) ............................................................................................................. 32.2 liters
[34 U.S. Quarts]
Standard Modulating Thermostat Range .............................................................. 82°C to 94°C [180°F to 202°F]
Standard LTA Thermostat Range .......................................................................... 69°C to 78°C [157°F to 172°F]
Maximum Coolant Pressure (Exclusive of Pressure Cap) ............................................................. 241 kPa [35 psi]
Maximum Allowable Top Tank Temperature ..................................................................................... 100°C [212°F]
Minimum Recommended Top Tank Temperature .............................................................................. 70°C [160°F]
Maximum Allowable Deaeration Time .................................................................................................. 25 Minutes
Minimum Allowable Drawdown or 20% of System Capacity (whichever is greater) .......... 11 liters [12 U.S. Quarts]
Minimum Allowable Pressure Cap ................................................................................................... 50 kPa [7 psi]
Exhaust System
Back Pressure - Maximum (at rated speed and load): ......................................................... 75 mm Hg [3.0 in Hg]
Exhaust Pipe Size (Normally Acceptable Inside Diameter):
• All Ratings ............................................................................................................................ 152 mm [6.0 in]
Service Tools QSK19
Service Tools
Engine Testing

Vacuum Gauge
Used to check fuel filter or intake air restriction.
ST-434
ProCarManuals.com
Manometer
Used with tool, Part No. 3375150, for measuring blowby.
ST-1111-3
Lubricating Oil Sampling Filter

Used to monitor oil contamination.
ST-1135
Pressure Gauge [0-75 In-Hg]

Used to measure intake manifold pressure and fuel drain line
restriction.
ST-1273
Pressure Gauge [0-100 psi]

Used to measure lubricating oil pressure.
3375275
Pressure Gauge [0-300 psi]

Used to measure fuel pressure. Includes necessary hoses and
hardware to attach to a fuel pump. Part No. ST-435-1 is the hose
3375932 and Part No. ST-435-6 is the pressure gauge.
QSK19 Service Tools

Fuel Measuring Device
Measure the rate of fuel consumption of a Cummins diesel en-
gine.
3376375
Digital Optical Tachometer

Used to measure engine speed (RPM).
3377462
Blowby Check Tool

Used with manometer, Part No. ST-1111-3, to measure the engine
crankcase pressure.
3822566
0.302 inch
orifice
ProCarManuals.com
Blowby Check Tool

crankcase pressure.
3823567
0.354 inch
orifice
Blowby Check Tool

crankcase pressure.
3822568
0.406 inch
orifice
Engine Dynamometer Control

Used on an engine dynamometer to control the QSK19 engine.
3162245
INSITE™ Software Kit

Used to troubleshoot, program, and adjust the QSK Fuel System.
3824801
Dynamometer Worksheet (014-001) QSK19
Dynamometer Worksheet (014-001)

Worksheet
Date: Repair Order No: Operator:
ESN: CPL: Fuel Pump Code:
Complaint: SC Code:
PARAMETER CODE SPECIFICATIONS ACTUAL READING

Fuel Pressure (psi @ rpm) 150 to 180 psi at Idle
Fuel Pressure (psi @ rpm) 225 to 250 psi at 1800 rpm
Fuel Pressure (psi @ rpm) 250 to 300 psi at 2100 rpm
Fuel Rate (lb/hr)
Intake Mfd. Pressure (in.Hg) See Fuel Pump Code
Intake Mfd. Temperature
*Intake Air Restriction 25 in. H2O, Maximum
*Exhaust Air Restriction 3 in. Hg, Maximum
*Fuel Inlet Restriction 8 in. Hg (Dirty Filter), Maximum
*Fuel Drain Line Restriction 3 psi, Maximum
Engine Blowby See Tables
* Recorded at maximum horsepower speed and full load
Road Speed Limit Engine High Speed Limit

ProCarManuals.com
Check Oil Level Low High OK Fuel Quality OK Not OK
Turbo Intake Lube HP

Engine Fuel Fuel Inlet Air Manifold Coolant Engine Oil or
Speed *Rate/Press Temp Temp Temp/Press Temp/Press Blowby Press Torque
* Be sure that the fuel rate is corrected for temperature.
Fuel Temperature Correction for Flow Rate Pressure Conversions

Less than 7°C[45°F] Flow meter not accurate
7 to 13°C[45 to 55°F] Subtract 2% from flow rate reading
1 in. H20 = 0.074 in. Hg = 0.036 psi
13.0 to 20.0°C[55 to 68°F] Subtract 1% from flow rate reading
1 in. Hg = 13.514 in. H20 = 0.491 psi
20.0 to 29°C[68 to 85°F] No Correction
1 psi = 2.036 in. Hg = 27.7 in. H20
29 to 42°C[85 to 108°F] Add 1% to flow rate reading
42 to 56°C[108 to 132°F] Add 2% to flow rate reading
56°C above [132°F] Flow meter not accurate.
This Page Can Be Copied For Your Convenience.

QSK19 Engine Testing (Chassis Dynamometer) (014-002)
Engine Testing (Chassis

Dynamometer) (014-002)
Setup
The performance of an engine installed in on-highway ve-
hicles can be tested on a chassis dynamometer.
NOTE: Due to driveline inefficiencies and engine-driven
accessories, the rated horsepower will be reduced by ap-
proximately:
• 20 percent for single axle vehicles
• 25 percent for tandem axle vehicles
The net horsepower available is called Wheel Horsepower
(WHP).
NOTE: Operate the vehicle in a gear that produces a road
speed of 90 to 95 Km/H [55 to 60 MPH].
CAUTION
Before installing or operating a vehicle on a chassis
dynamometer, follow all the vehicle manufacturer’s
safety precautions.
ProCarManuals.com
CAUTION
Low profile radial tires are more sensitive to heat than
bias ply tires. Excessive operating time at full load can
damage tires due to overheating. Check the tire manu-
facturer’s recommendations for the maximum allow-
able chassis dynamometer operating time.
Engine Testing (Chassis Dynamometer) (014-002) QSK19
Adjust the vehicle and dynamometer room exhaust system

to be sure that all exhaust gases are removed from the
room.
Refer to the chassis dynamometer and vehicle manufac-
turer’s recommendations and specifications for testing
procedures.
Be sure all instrumentation is removed before removing the

vehicle from the dynamometer.
ProCarManuals.com
General Engine Test Procedures

NOTE: The lubricating oil system must be primed before
operating the engine after rebuild to avoid internal com-
ponent damage. Do not prime the system from the bypass
filter as the filter will be damaged.
Remove the large plug from the oil cooler housing.
Use a pump capable of supplying 205 kPa [30 psi] con-

tinuous pressure. Connect the pump to the front of the
engine oil cooler as shown.
Use a supply of clean oil. Turn the pump to the ON position.
Check the engine oil pressure gauge. When the gauge
indicates oil pressure, begin monitoring the oil level in the
oil pan.
Check the engine lubricating oil level to be sure it is filled

to the proper level.
WARNING
Check the coolant level only when the engine is
stopped. Wait until the coolant temperature is below
50°C [120°F] before removing the pressure cap. Failure
to do so can cause personal injury from heated coolant
spray.
CAUTION
ProCarManuals.com
Do not add cold coolant to a hot engine. This can cause

engine casting damage. Allow the engine to cool to
below 50°C [120°F] before adding coolant.
Check the engine coolant level to be sure it is filled to the
proper level. Refer to Procedure 008-018.
NOTE: Use a known source of good quality No. 2 diesel

fuel.
This is very important since No. 1 diesel fuels, along with
most other alternate fuels, are lighter (lower specific grav-
ity, higher API gravity) than No. 2 diesel fuel. The lighter the
fuel, the lower the energy content (BTU) per gallon (liter,
etc.).
Engine operating specifications can be found in publica-

tions available from your local Cummins Authorized Repair
Location.
Test
To properly monitor engine performance, record the fol-
lowing parameters. To limit dynamometer operating time,
instrument the engine to perform as many checks as pos-
sible.
• Engine speed rpm with a verified tachometer
• Fuel pressure
• Fuel rate (Use Service Tool, Part No. 3376375)
• Fuel temperature (if needed to correct fuel rate)
• Fuel inlet restriction
• Fuel drain line restriction
• Intake manifold pressure
• Intake air restriction

• Exhaust air restriction
• Coolant temperature
• Engine blowby
• Lubricating oil pressure
ProCarManuals.com
• Coolant pressure
• Inlet manifold air temperature
• Turbocharger inlet air temperature
Engine Speed (rpm) With a Verified Tachometer

Use digital optical tachometer, Part No. 3377462, to check
and verify engine speed.
Fuel Supply Pressure

Refer to Procedure 005-016-013.
Fuel Rate
Use fuel measuring device, Part No. 3376375, to measure
the rate of fuel consumption. Refer to General Information
located in the front of this section.
Fuel Inlet Restriction

Measure the fuel inlet restriction. Install a vacuum gauge,
Part No. ST-434, between the fuel filter and the gear pump
inlet.
NOTE: Do not measure fuel inlet restriction with the fuel
measuring device installed. This will not measure the inlet
restriction of the vehicle’s supply plumbing.
ProCarManuals.com
Fuel Drain Line Restriction

Use Pressure Gauge, Part No. ST-1273, to measure fuel
drain line restriction.
NOTE: Do not measure fuel drain line restriction with the
fuel measuring device installed. This will not measure the
drain line restriction of the vehicle’s return plumbing.
Intake Manifold Pressure

Measure the intake manifold or INSITE™ pressure (turbo-
charger boost). Install pressure gauge, Part No. ST-1273,
in the intake manifold as shown.
Observe the reading on the pressure gauge.
Intake Air Temperature Control - Chassis Dynamometer

Test
When operating an engine on a chassis dynamometer,
follow these steps for best results and safe operation.
If the engine is equipped with automatic fan, lock the cool-
ing fan in the ON mode. This can be done by installing a
jumper across the temperature switch, or by supplying
shop air to the control valve. Refer to the fan drive manu-
facturer for the recommended procedure.
Monitor the intake manifold air temperature using INSITE™

in the monitor mode, or install Fluke digital thermometer,
Part No. 3822666, and thermocouple wire kit, Part No.
3822988, into the intake manifold.
The intake manifold air temperature must not exceed 77°C
[170°F].
Maintain intake manifold air temperature to 66°C [150°F]
or below during chassis dynamometer operation.
ProCarManuals.com
If the intake manifold temperature exceeds 77°C [170°F],

shut off the engine. Allow the engine to cool.
Check the fan drive. Be sure the fan is locked in the ON
mode.
Remove any obstructions such as a winterfront or debris.
Manually lock the shutters in the OPEN position if equipped.
Inspect the dynamometer room for adequate supply of
suitably cool or outside air. Make sure that dynamometer
room recirculation is not an issue.
Resume the test.
Intake Air Restriction

Measure the inlet air restriction. Install the vacuum gauge,
Part No. ST-434, or a manometer, Part No. ST-1111–3, in
the intake air piping.
NOTE: The gauge adapter must be installed at a 90 degree
angle to the air flow in a straight section of pipe at a
minimum of one pipe diameter before the turbocharger.
Refer to Procedure No. 010-031-010.
Exhaust Restriction
Measure the exhaust air restriction. Install the pressure
gauge, Part No. ST-1273, or a manometer in the exhaust
air piping.
The gauge adapter must be installed near the turbocharger
in a straight section of pipe at the turbine outlet.
Engine Blowby
NOTE: Excessive blowby indicates an air compressor, a
turbocharger, or an engine malfunction, allowing combus-
tion gases or air to enter the crankcase and build a pressure
higher than normal.
This procedure describes how to measure crankcase pres-
sure and how to determine the component that is malfunc-
tioning.
ProCarManuals.com
Use one of the three blowby service tools and a water

manometer Part No. ST-1111-3. Maximum gauge capacity
is 1270 mm-H20 [50 in-H20].
The engine blowby tools are similar in design. The differ-
ence between the tools is in the size of the orifice.
Blowby Tool Orifice Size
Part No. [Inch]
3822566 [0.302]
3822567 [0.354]
3822568 [0.406]
Use a length of hose (1) to attach the blowby tool to one of

the crankcase breathers.
Plug all of the other breathers.
Attach a manometer to the location shown (2).
Operate the engine at rated rpm and full load (wide open
throttle) until a steady reading is obtained.
Compare the blowby readings to previous readings on the
engine. If previous readings for the engine are not avail-
able, compare the blowby reading to new engine specifi-
cations.
NOTE: A sudden increase in blowby indicates a problem.
A gradual increase over a period of time is normal (due to
wear of internal engine components).
ProCarManuals.com
Specifications
Engine Blowby New/Rebuilt Used

7.67 mm [0.302 in] Orifice:
RPM mm H20 [in H20] mm H20 [in H20]
All ratings 508 [20] 1270 [50]
2000 and above 355 [14] 889 [35]
1500 to 1900 305 [12] 762 [30]

All ratings 229 [9] 584 [23]
2000 and above 203 [8] 508 [20]
1500 to 1900 178 [7] 457 [18]

All ratings 127 [5] 330 [13]
If the blowby is higher than normal, check the crankcase

breathers and breather tubes to see if they are plugged.
ProCarManuals.com
1. Wing Nut
2. Washer
3. Breather Cap
4. Screen Mesh
5. Breather Element
6. Breather Base
Check the engine oil level. If the level is too high, it can
cause a higher than normal crankcase pressure.
Isolate the turbocharger to determine if the high crankcase

pressure is due to seal leakage in the turbocharger.
WARNING
Disconnect the turbocharger drain line from the oil pan
adaptor.
Install a hose assembly with the two shutoff valves ar-
ranged as shown. Place the other hose in an 8 to 19 liter
[2 to 5 gallon] bucket.
NOTE: The valves must have a minimum inside diameter
of 19 mm [0.75 in].
Close the valve (A) that allows the oil to drain to the bucket.
ProCarManuals.com
Open the valve (B) that allows the oil to drain into the
engine.
Operate the engine at rated speed. Record the blowby

value.
CAUTION
Do not operate the engine with valve A open and valve
B closed for more than 1 minute. Operation for more
than 1 minute can result in severe engine damage.
Continue operating at rated speed and load. Open valve A
and close valve B. Record the blowby reading.
Compare the value to the original reading. If the blowby is

now acceptable, replace the turbocharger.
ProCarManuals.com
Isolate the air compressor to determine if it is malfunction-

ing and causing the high blowby pressure.
Relieve the air pressure on the first air tank in the system
after the air compressor (wet tank).
Disconnect the air inlet and outlet connections. Plug the
intake manifold or air piping where the inlet connection was
removed.
Operate the engine at rated speed and full load (wide open
throttle) until a steady blowby reading is obtained.
Compare the blowby readings to the previous value. If the
blowby is now acceptable, replace the air compressor.
A sudden increase in blowby or a high reading that is not

steady indicates that there is internal damage in the engine.
Lubricating Oil Pressure

Use Pressure Gauge, Part No. 3375275, to measure lu-
bricating oil pressure.
Install the pressure gauge to the main oil rifle (1) or oil filter
head (2).
Low Idle (minimum allowable) 138 kPa [20 psi]
At 1200 rpm (minimum allowable) 207 kPa [30 psi]
ProCarManuals.com
Coolant Pressure
Measure the coolant pressure at the water manifold (1).
Maximum Coolant Pressure with Closed Thermostat
and No Pressure Cap 241 kPa [35 psi]
Air Compressor
NOTE: All air compressors manufactured by Cummins En-
gine Company, Inc. must be operating during the engine
run-in. During the performance check, all air compressors
must be in the unload or non-operating mode.
Connect a source of compressed air capable of producing
665 kPa [95 psi] to the air compressor unloader (1). This air
line must contain a valve between the source and the
unloader.
NOTE: The compressed air load in the accompanying il-
lustration must be attached to the air compressor outlet (2).
QSK19 Engine Run-in (Chassis Dynamometer) (014-003)
Use an air tank (2). Install an air regulator (3) capable of

maintaining 345 to 517 kPa [50 to 75 psi] air pressure at
both minimum and maximum engine rpm.
Install a steel tube or high temperature hose (1).
Hose Temperature (Minimum) 260 °C [500 °F]
Connect the tube or hose (1) to the air compressor outlet.
Starting Motor
Inspect the voltage rating on the starting motor before
installing the electrical wiring.
Install the electrical wiring to the starting motor and bat-
teries, if used.
NOTE: If another method of starting the engine is used,
follow the manufacturer’s instructions to make the neces-
sary connections.
ProCarManuals.com
Engine Run-in (Chassis

General Information

oil pan.
Engine Run-in (Chassis Dynamometer) (014-003) QSK19

WARNING
spray.
CAUTION
ProCarManuals.com

Check the engine coolant level to make sure it is filled to
the proper level. .

fuel.
etc.).
Engine Throttle Control

Engines that are run on an engine dynamometer require
that the engine harness be installed, and connected to the
engine. Additionally, a special engine dynamometer ver-
sion of the OEM wiring harness and throttle control must
be installed.
A special wiring harness and throttle control has been
developed to enable engine operation out of the chassis.
Engine Dynamometer Kit, Part No. 3162245.

Location.
ProCarManuals.com
Engine Run-in (Chassis Dynamometer) (014-003) QSK19
Run-In Instructions
Refer to Chassis Dynamometer - Operation, Procedure No.
014-002, for general operating procedures and safety
precautions.
Use this chart to determine the test load.

Example: The test load for a 475 HP engine rated at 2000 rpm with a 15 percent torque rise is 225 ft-lb.
NOTE: This chart assumes the dynamometer constant is 5252. If the dynamometer constant is not 5252, use the
following formula to determine the correct test load:
Correct test load = (Dynamometer constant) x (Test load) /d 5252.
Example: The dynamometer constant for testing the engine in the above example is 4000.
ProCarManuals.com
Correct test load = (4000 x 225) /d 5252 = 171 ft-lb.

NOTE: This chart assumes vehicle run-in on a chassis dynamometer.
Rated RPM Rated Torque Rise Test Load
Horsepower
1200 All All 305 N•m
[225 ft-lb]
1500 All All 305 N•m
[225 ft-lb]
1800 0 to 499 All 305 N•m
[225 ft-lb]
1800 500 and All 380 N•m
ABOVE [280 ft-lb]
1900 0 to 474 All 305 N•m
[225 ft-lb]
1900 475 and All 380 N•m
ABOVE [280 ft-lb]
2000 0 to 499 0 to 24% 305 N•m
[225 ft-lb]
2000 0 to 499 25% and 380 N•m
ABOVE [280 ft-lb]
2000 500 and All 380 N•m
ABOVE [280 ft-lb]
2100 0 to 474 0 to 32% 305 N•m
[225 ft-lb]
2100 0 to 474 33% Plus 305 N•m
[225 ft-lb]
2100 475 to 530 0 to 15% 305 N•m
[225 ft-lb]
2100 475 to 530 16% and 380 N•m
ABOVE [280 ft-lb]
2100 531 to 649 All 380 N•m
[280 ft-lb]
2100 650 and All 405 N•m
ABOVE [300 ft-lb]
Adjust the engine rpm to 1200 rpm. Adjust the dynamom-

eter load to the test load as previously determined. Operate
the engine at this setting until the coolant temperature
indicates 70°C [160°F].
Check for leaks. Fix all leaks.
Check all of the gauges and record the readings.
Do not proceed to the next step until the blowby becomes
stable within specifications.
Adjust the engine rpm to the torque peak rpm. Adjust the
dynamometer load to equal two times the test load. Op-
erate the engine for 2 minutes.
Check all the gauges and record the readings.
ProCarManuals.com
Maintain the engine rpm at torque peak rpm. Increase the

dynamometer load to equal three times the test load.
Operate the engine at this load for 2 minutes.
Move the throttle lever to the FULL OPEN position. In-

crease the load until the engine rpm is at torque peak rpm.
Operate the engine at this setting for 10 minutes or until the
blowby becomes stable within specifications.
Engine Run-in (Without Dynamometer) (014-004) QSK19
Decrease the dynamometer load until the engine rpm in-

creases to the rated RPM.
Decrease the dynamometer load completely.

CAUTION
Do not turn the engine OFF immediately. The engine
must be allowed to cool or damage to the turbocharger
may result.
Move the throttle lever to the LOW IDLE position. Operate
the engine at this setting for 3 to 5 minutes. This will allow
the turbocharger and the other engine components to cool.
ProCarManuals.com
CAUTION
Do not operate the engine at IDLE longer than speci-
fied. Excessive carbon formation can cause engine
damage.
Turn the engine OFF.
Engine Run-in (Without

Preparatory
QSK19 Engine Run-in (Without Dynamometer) (014-004)

oil pan.

ProCarManuals.com
WARNING
spray.
CAUTION
Check the engine coolant level to make sure it is filled to
the proper level.

fuel.
etc.).
Engine Run-in (Without Dynamometer) (014-004) QSK19

Location.
Run-In Instructions
that the engine harness be installed, and connected to the
be installed.
ProCarManuals.com
Engine Dynamometer Kit, Part No. 3162245.
Generator Set
Operate the engine in steps, varying the load from 25 to 100
percent, until blowby remains constant.
Off-Highway
Operate the equipment in the normal duty cycle at part load
during the first 3 hours after rebuild.
QSK19 Engine Testing (Engine Dynamometer) (014-005)
Do not idle the engine for more than 5 minutes at any one
time.
Do not operate the engine at rated rpm. Operate at 75
percent of rated RPM or lower.
Rated RPM Max RPM for First 3
Hours
2100 1575
2000 1500
1900 1425
1800 1350
Do not operate the engine at full load for more than 5

minutes at any one time.
ProCarManuals.com
Engine Testing (Engine

Install
NOTE: Be sure the dynamometer capacity is sufficient to
permit testing at 100 percent of the engine rated horse-
power. If the capacity is not enough, the testing procedure
must be modified to the restrictions of the dynamometer.
Use engine lifting fixture, Part No. 3822512, to install the
engine to the test stand. Align and connect the dynamom-
eter. Refer to the manufacturer’s instructions for aligning
and testing the engine.
Refer to Service Bulletin No. 3666005, Dynamometer and
Road Engine Testing, for detailed instructions on auxiliary
aftercooling system attachment.
NOTE: Some engines are equipped with fittings used for

CompuchekT testing sensors. The sensor probes used for
CompuchekT and dynamometer testing are not compat-
ible. If the same location is used, remove the CompuchekT
fitting and install adapters for the dynamometer sensor.
Install the coolant pressure sensor (1).
Install the coolant temperature sensor (2).
Engine Testing (Engine Dynamometer) (014-005) QSK19
Coolant Plumbing
Connect the coolant supply to the water inlet connection.
Connect the coolant return to the water outlet connection.
Install the drain plugs and close all of the water drain cocks.
NOTE: LTA engines require connecting the LTA water lines
to a remote heat exchanger.
Intake Air Temperature Control

The use of a remote heat exchanger is mandatory when-
ever a Cummins LTA engine is attached to an engine dy-
namometer for the purpose of engine run-in, performance
testing and engine diagnostics. Do not attempt to run a
Cummins LTA engine without any means of controlling the
intake manifold air temperature.
A = Aftercooler water OUT
ProCarManuals.com
B = Aftercooler water IN
C = Water OUT to drain
D = Cool water IN
LTA (Low Temperature Aftercooling)

All QSK19 ratings of 601 HP and above require Low Tem-
perature Aftercooling (LTA) and, therefore, have unique ra-
diator requirements. The ratings of 600 HP and below do
not require LTA. The LTA is a one-pump, two-loop cooling
system.
NOTE: The heat exchanger must be sized to maintain
70°C [160°F] maximum intake air temperature at full power.
A = Water IN
B = Thermostat housing
C = LTA OUT
D = Water OUT
E = LTA return


oil pan.
WARNING
spray.
CAUTION
ProCarManuals.com

Check the engine coolant level to be sure it is filled to the
proper level.


fuel.
etc.).
Engine Throttle Control

that the engine harness be installed and connected to the
be installed.
Engine Dynamometer Kit Part No. 3162245.
Engine operating specifications are available from your

local Cummins Authorized Repair Location.
ProCarManuals.com
Test
To properly monitor engine performance, record the fol-
lowing parameters. To limit dynamometer operating time,
instrument the engine to make as many checks as possible.
• Engine speed rpm with a verified tachometer
• Fuel pressure
• Fuel rate (Use Service Tool, Part No. 3376375)
• Fuel temperature (if needed to correct fuel rate)
• Fuel inlet restriction
• Fuel drain line restriction
• Intake manifold pressure
• Intake air restriction

• Exhaust air restriction
• Coolant temperature
• Engine blowby
• Lubricating oil pressure
• Coolant pressure
• Inlet manifold air temperature
• Turbocharger inlet air temperature
Engine Speed (RPM) With a Verified Tachometer

Use digital optical tachometer, Part No. 3377462, to check
and verify engine speed.
Fuel Supply Pressure

Refer to Procedure 005-016.
ProCarManuals.com
Fuel Rate
Use fuel measuring device, Part No. 3376375, to measure
the rate of fuel consumption. Refer to General Information
in the front of this section.
Fuel Inlet Restriction

Measure the fuel inlet restriction. Install a vacuum gauge,
Part No. ST-434, between the fuel filter and the gear pump
inlet.
NOTE: Do not measure fuel inlet restriction with the fuel
measuring device installed. This will not measure the inlet
restriction of the vehicle’s supply plumbing.
Fuel Drain Line Restriction

Use Pressure Gauge, Part No. ST-1273, to measure fuel
drain line restriction.
NOTE: Do not measure fuel drain line restriction with the
fuel measuring device installed. This will not measure the
drain line restriction of the vehicle’s return plumbing.
Intake Manifold Pressure

Measure the intake manifold pressure (turbocharger boost).
Install pressure gauge, Part No. ST-1273, in the intake
manifold as shown.
Observe the reading on the pressure gauge.
ProCarManuals.com
Intake Air Restriction

Measure the inlet air restriction. Install the vacuum gauge,
Part No. ST-434, or a manometer in the intake air piping.
NOTE: The gauge adapter must be installed at a 90 degree
angle to the air flow in a straight section of pipe at a
minimum of one pipe diameter before the turbocharger.
Exhaust Restriction
Measure the exhaust air restriction. Install the pressure
gauge, Part No. ST-1273, or a manometer in the exhaust
air piping.
The gauge adapter must be installed near the turbocharger
in a straight section of pipe at the turbine outlet.
Engine Blowby
NOTE: Excessive blowby indicates an air compressor, a
turbocharger, or an engine malfunction, allowing combus-
tion gases or air to enter the crankcase and build a pressure
higher than normal.
This procedure describes how to measure crankcase pres-
sure and how to determine the component that is malfunc-
tioning.
Use one of the three blowby service tools and a water
manometer, Part No. ST-1111-3. Maximum gauge capacity
is 1270 mm-H20 [50 in-H 20].
The engine blowby tools are similar in design. The differ-
ence between the tools is in the size of the orifice.
Blowby Tool Orifice Size
Part No. [inch]
3822566 [0.302]
3823567 [0.354]
3822568 [0.406]
Use a length of hose (1) to attach the blowby tool to one of

the crankcase breathers.
Plug all of the other breathers.
ProCarManuals.com
Attach a manometer to the location shown (2).
Operate the engine at rated rpm and full load (wide open
throttle) until a steady reading is obtained.
Compare the blowby readings to previous readings on the
engine. If previous readings for the engine are not avail-
able, compare the blowby reading to new engine specifi-
cations.
NOTE: A sudden increase in blowby indicates a problem.
A gradual increase over a period of time is normal (due to
wear of internal engine components).
QSK19 Blowby Limits

(1500 - 1900) [12 in H2O] [30 in H2O]
[20 in H2O] [50 in H2O]
QSK19 Blowby Limits

(1500 - 1900) [7 in H2O] [18 in H2O]
[9 in H2O] [23 in H2O]
ProCarManuals.com
QSK19 Blowby Limits

All Ratings 127 mm H2O 330 mm H2O
[5 in H2O] [13 in H2O]
If the blowby is higher than normal, check the crankcase

breathers and breather tubes to see if they are plugged.
1. Wing Nut
2. Washer
3. Breather
4. Screen Mesh
5. Breather Element
6. Breather Base
Check the engine oil level. If the level is too high it can
cause a higher than normal crankcase pressure.
Isolate the turbocharger to determine if the high crankcase

pressure is due to seal leakage in the turbocharger.
Disconnect the turbocharger drain line from the oil pan
adaptor.
Install a hose assembly with the two shutoff valves ar-
ranged as shown. Place the other hose in an 8 to 19 liter
[2 to 5 gallon] bucket.
NOTE: The valves must have a minimum inside diameter
of 19 mm [0.75 inch].
Close the valve (A) that allows the oil to drain to the bucket.
ProCarManuals.com
Open the valve (B) that allows the oil to drain into the
engine.
Operate the engine at rated speed.

CAUTION
Do not operate the engine with valve A open and valve
B closed for more than 1 minute. Operation for more
than 1 minute can result in severe engine damage.
Continue operating at rated speed and load. Open valve A
and close valve B. Record the blowby reading.
Compare the value to the original reading. If the blowby is

now acceptable, replace the turbocharger.
Isolate the air compressor to determine if it is malfunction-

ing and causing the high blowby pressure.
Relieve the air pressure on the first air tank in the system
after the air compressor (wet tank).
Disconnect the air inlet and outlet connections. Plug the
intake manifold or air piping where the inlet connection was
removed.
ProCarManuals.com
Operate the engine at rated speed and full load (wide open
throttle) until a steady blowby reading is obtained.
Compare the blowby readings to the previous value. If the
blowby is now acceptable, replace the air compressor.
A sudden increase in blowby or a high reading that is not

steady indicates that there is internal damage in the engine.

Use Pressure Gauge, Part No. 3375275, to measure lu-
bricating oil pressure.
Install the pressure gauge to the main oil rifle (1) or air filter
head (2).

kPa psi
138 MIN 20
207 NOMINAL 30
Coolant Pressure
Measure the coolant pressure at the water manifold (1).
Coolant Pressure
kPa psi
241 NOMINAL 35
ProCarManuals.com
Air Compressor
NOTE: All air compressors manufactured by Cummins En-
gine Company, Inc. must be operating during the engine
run-in. During the performance check, all air compressors
must be in the unload or non-operating mode.
Connect a source of compressed air capable of producing
665 kPa [95 psi] to the air compressor unloader (1). This air
line must contain a valve between the source and the
unloader.
NOTE: The compressed air load in the accompanying il-
lustration must be attached to the air compressor outlet (2).
Use an air tank (2). Install an air regulator (3) capable of

maintaining 345 to 517 kPa [50 to 75 psi] air pressure at
both minimum and maximum engine rpm.
Install a steel tube or high temperature hose (1).
260°C [500°F].
Connect the tube or hose (1) to the air compressor outlet.
Engine Run-in (Engine Dynamometer) (014-006) QSK19
Starting Motor
Inspect the voltage rating on the starting motor before
installing the electrical wiring.
Install the electrical wiring to the starting motor and bat-
teries, if used.
NOTE: If another method of starting the engine is used,
follow the manufacturer’s instructions to make the neces-
sary connections.
Engine Run-in (Engine Dynamometer)

(014-006)
General Information
This section outlines engine testing and engine run-in rec-
ommendations for QSK19 engines. All engines must be
run-in after a rebuild or a repair involving the replacement
of one or more piston ring sets, cylinder liners or pistons.
ProCarManuals.com
Incorrect or insufficient break-in of the piston rings will

lead to early oil consumption or high blowby complaints.
Adherence to these run-in guidelines will allow the full
durability of new pistons, liners, and rings to be real-
ized.
Before running the engine, make sure the engine is filled
with the proper coolant. Also, make sure the lubricating oil
system is filled and primed.
In-Service Run-In
The following in-service run-in guidelines are recommended
for QSK19 engines after a repair involving replacement of
one or more of the piston ring sets, cylinder liners or pistons
where engine or an engine dynamometer and/or chassis
dynamometer run-in cannot be performed.
The majority of heavy duty diesel applications will provide
sufficient run-in under normal loaded operations. However,
light load/high rpm operation must be avoided during the
run-in period.
QSK19 Engine Run-in (Engine Dynamometer) (014-006)
Engine Dynamometer Run-In

This is the preferred method of run-in for engines that have
been rebuilt out-of-chassis. It is not practical, nor recom-
mended that an engine be removed from the application to
conduct the run-in after a rebuild or cylinder repair has
been performed in-chassis. There is no requirement, nor is
it recommended for an engine that has been run-in and
tested on an engine dynamometer to be run-in again after
it has been reinstalled in the vehicle or equipment.
Chassis Dynamometer, Portable Dynamometer or Load
Bank Run-In
When it is not possible to load an engine immediately after
rebuild or repair, (example: on-highway tractor that must be
‘‘bobtailed’’ for delivery, a standby generator or fire pump
that cannot be operated because of customer restrictions,
a fire truck that cannot be loaded with the water pump,
etc.), the engine must be run-in on a chassis dynamometer,
portable dynamometer or load bank following the recom-
mendations outlined in the attached procedures.
ProCarManuals.com
Run-In Instructions
Refer to Engine Testing-Engine Dynamometer, Procedure
No. 014-005, for general operating procedures and safety
precautions.
Use this chart to determine the test load.

The run-in test must be performed with the engine operating at torque peak rpm. Operate a generator set engine at
rated rpm.
Example: The test load for a 475 HP engine rated at 2000 rpm with a 15 percent torque rise is [300 ft-lb].
NOTE: This chart assumes the dynamometer constant is 5252. If the dynamometer constant is not 5252, use the
following formula to determine the correct test load:
Correct test load = (Dynamometer constant) x (Test load) /d 5252.
ProCarManuals.com
Example: The dynamometer constant for testing the engine in the above example is 4000.
Correct test load = (4000 x 300) /d 5252 = [228 ft-lb].
NOTE: This chart assumes vehicle run-in on a chassis dynamometer.
Rated RPM Rated Horsepower Torque Rise Test Load
1200 All All 405 N•m [300 ft-lb]
1500 All All 405 N•m [300 ft-lb]
1800 0 to 499 All 405 N•m [300 ft-lb]
1800 500 and ABOVE All 510 N•m [375 ft-lb]
1900 0 to 474 All 405 N•m [300 ft-lb]
2000 0 to 499 0 to 24% 405 N•m [300 ft-lb]
2000 0 to 499 25% and ABOVE 510 N•m [375 ft-lb]
2100 0 to 474 0 to 32% 405 N•m [300 ft-lb]
2100 0 to 474 33% Plus 405 N•m [300 ft-lb]
2100 475 to 530 0 to 15% 405 N•m [300 ft-lb]
2100 475 to 530 16% and ABOVE 510 N•m [375 ft-lb]
2100 531 to 649 All 510 N•m [375 ft-lb]
QSK19 Engine Run-in (Engine Dynamometer) (014-006)
CAUTION
Do not crank the starting motor for more than 30 sec-
onds. Excessive heat will damage the starter.
START the engine. If the engine does not begin operating
after 30 seconds, allow two minutes for the starting motor
to cool.
CAUTION
If the oil pressure is not within specifications, STOP the
engine immediately. Both low and high oil pressure will
cause engine damage.
Main Oil Rifle Pressure (At Idle)
kPa psi
138 MIN 20
483 MAX 70
Operate the engine at the IDLE position. Check for leaks.

CAUTION
fied. Excessive carbon formation will cause engine
damage.
ProCarManuals.com
Adjust the engine rpm to 1200 rpm. Adjust the dynamom-

eter load to the test load as previously determined. Operate
the engine at this setting until the coolant temperature
indicates 70°C [160°F].
Check for leaks. Fix all leaks.
Check all of the gauges and record the readings.
Adjust the engine rpm to the torque peak rpm. Adjust the
dynamometer load to equal two times the test load. Op-
erate the engine for two minutes.
Maintain the engine rpm at torque peak rpm. Increase the

dynamometer load to equal three times the test load.
ProCarManuals.com
Move the throttle lever to the FULL OPEN position. In-

crease the load until the engine rpm is at torque peak rpm.
Operate the engine at this setting for 10 minutes or until the
blowby becomes stable within specifications.
Decrease the dynamometer load until the engine rpm in-

creases to the rated rpm.
QSK19 Engine Testing (In Chassis) (014-008)
Decrease the dynamometer load completely.

CAUTION
Do not turn the engine OFF immediately. The engine
must be allowed to cool.
Move the throttle lever to the LOW IDLE position. Operate
the engine at this setting for 3 to 5 minutes. This will allow
the turbocharger and the other engine components to cool.
CAUTION
fied. Excessive carbon formation can cause engine
damage.
Turn the engine OFF.

ProCarManuals.com
Engine Testing (In Chassis) (014-008)

Stall Speed Check
The stall speed is the engine speed (rpm) obtained at full
throttle when the converter output shaft is locked.
The vehicle brakes do not always hold an electronically
controlled transmission.
CAUTION
Do not exceed 120°C [250°F] converter oil tempera-
ture. If the oil temperature exceeds 120°C [250°F], put
the transmission in neutral and operate the engine until
the oil temperature is below 120°C [250°F]. Check the
converter oil level.
Engine Testing (In Chassis) (014-008) QSK19
The following equipment is needed for this check:

• Stop watch
• Digital tachometer, Part No. 3375631. or a hand held
optical tachometer, Part No. ST-3377462.
• Equipment manufacturer’s stall speed and time to
stall specifications.
Install the tachometer on the fuel pump.

ProCarManuals.com
Put the gear selector in the highest gear or full forward.

In some types of equipment it is also necessary to engage
the hydraulics.
Be sure the vehicle has good brakes and air pressure in the
brake system.
The brakes must prevent the vehicle from moving when the
engine is at full throttle.
Engage the vehicle brakes or keep the vehicle from moving.
Operate the engine until the coolant temperature is up to

70°C [160°F] and the converter temperature is 80°C
[180°F] or above.
Alternately, shift from neutral to the highest speed gear
possible and operate at part throttle. This will warm the
entire system uniformly.
Bring the engine speed back to low idle.

ProCarManuals.com
NOTE: Do not exceed 120°C [250°F] converter oil tem-

perature.
Move the throttle to the full open position. Do not perform
this test for more than 15 seconds. If the engine speed
continues to slowly increase, the torque converter fluid is
being overheated.
Check the engine speed (rpm) at the point of stall.

Always hold the speed until it is stable.
Take several readings. Be sure the reading is accurate.
Check the stall speed (rpm) against the specifications that

are for the equipment, converter, or automatic transmis-
sion.
NOTE: The stall speed for the engine and converter/
transmission can vary plus/minus 8 percent (±8%) from
the manufacturer’s specifications.
If the stall speed is not within the specifications, refer to the

Stall Speed Check List at the end of this section.
Check the equipment manufacturer’s troubleshooting pro-
cedures for other reasons for stall speed problems.
ProCarManuals.com
If the cause for the stall speed being too low is low engine
power output, refer to the Engine Power Output Low Trouble-
shooting Chart. Make the correct repair based on the fuel
rate, fuel pressure, and intake manifold pressure readings.
Time Speed Check

After performing the Stall Speed Check through the torque
converter fluid being overheated, calculate the engine stall
speed.
Example: Stall speed 2089 (2089 x .90 = 1880 rpm).
Quickly move the throttle to the full open position and start
the stop watch at the same time.
When the engine speed is 90 percent (90%) of the stall

speed rpm, stop the stop watch.
NOTE: The type of unit and the stall speed rpm will be
different for different types of equipment. Most types have
a stall speed between 8 and 12 seconds.
ProCarManuals.com
Check the equipment manufacturer’s specifications for the

time to stall or the acceleration time.
If the time is excessive, refer to Troubleshooting Symptoms
Charts, Engine Acceleration/Response Poor.
Stall Speed Check List

If The Stall Speed Is Too Low, Check The Following:
1. _____ _____ The tachometer is in error.

2. _____ _____ The engine is up to or above 70°C [160°F].
3. _____ _____ The converter oil is up to temperature 80°C [180°F].
4. _____ _____ The stall has been held long enough for the engine to accel-
erate to full power.
5. _____ _____ The match curve stall speed was recorded correctly.
6. _____ _____ The converter oil is to the converter manufacturer’s recom-
mendation. Society of Automotive Engineers (Example: SAE
30 instead of SAE 10).
7. _____ _____ The engine driven accessory power requirements exceed 10
percent of the gross engine power. Check for abnormal ac-
cessory horsepower losses such as hydraulic pumps, large
fans, oversize, compressors, etc. Either remove the accessory
or accurately determine the power requirement and adjust
accordingly.
8. _____ _____ The unit is operating at an altitude high enough to affect the
engine power.
9. _____ _____ The converter charging pressure is correct.
10. _____ _____ The tailshaft governor is interfering with and preventing a full
throttle opening. (Disconnect the tailshaft governor.)
11. _____ _____ The converter blading is interfering or in a stage of failure.
ProCarManuals.com
Check the sump or filter for metal particles.

12. _____ _____ The converter stators are free-wheeling instead of locking.
13. _____ _____ The engine is set for power other than that specified on the
power curve.
14. _____ _____ The converter is wrong, due to improper build or rebuild of
unit.
15. _____ _____ The converter is performing to the published absorption
curve.
16. _____ _____ The engine and converter match is correct. Check the engine
and converter models for the proper match.
17. _____ _____ The engine is matched to an oversized converter. (If this con-
dition is believed to exist, please report the engine-converter-
accessory information to the factory.)
18. _____ _____ The engine power is down. (The engine torque rise could be
less than shown on the standard engine curve.) See the fuel
setting adjustments and the turbocharger air manifold pres-
sure check.
It is sometimes easier to change the engine fuel rate than to determine the true cause for low stall speed, but the
customer ends up with an over-fueled engine that will also negatively affect durability. Do not increase the fuel rate
as a CURE-ALL.
If The Stall Speed Is Too High, Check The Following:

Yes No
1. _____ _____ The engine is high in power.
2. _____ _____ The tachometer is in error.
3. _____ _____ The accessory power requirements are less than 10 percent
of the gross engine power.
4. _____ _____ The converter oil is aerating (foaming) - check for low oil
level, air leaks in suction line, oil does not contain a foam
inhibitor, or suction screen or filter. (Should be accompanied
by a noticeable loss of machine performance.)
5. _____ _____ The converter is being held at full stall. Check for a slipping
front disconnect clutch or a rotating output shaft. On the
converter-transmission package, this can be impossible to
check.
6. _____ _____ The converter turbine element is beginning to fail and losing
blades or the converter was originally built with the wrong
size element.
7. _____ _____ The engine and converter match is correct (due to a revision
in the engine rating or the converter performance).
8. _____ _____ On the transmission-converter units with oil sump in the
transmission, if the oil level is too high, it can cause severe
aeration due to parts dipping in the oil.
9. _____ _____ The converter is performing to the published absorption
curve.
10. _____ _____ The converter charging pressure is correct.
ProCarManuals.com
The reasons for abnormal stall speeds listed above are some which have been encountered by Cummins represen-
tatives and probably do not include all possible causes. The correction of the problem is either covered in the vehicle
service manual, the converter service manual, or is self-explanatory.
NOTES
ProCarManuals.com
Section 16 - Mounting Adaptations - Group 16 Page 16-a
Section 16 - Mounting Adaptations - Group 16

Section Contents
Page
Engine Support Bracket, Front...................................................................................................................... 16-4
Clean ......................................................................................................................................................... 16-4
Flywheel ......................................................................................................................................................... 16-4
Clean ......................................................................................................................................................... 16-4
Flywheel Housing .......................................................................................................................................... 16-6
Clean ......................................................................................................................................................... 16-6
Redowel ..................................................................................................................................................... 16-7
Flywheel Ring Gear ...................................................................................................................................... 16-10
Assemble .................................................................................................................................................. 16-11
Disassemble ............................................................................................................................................. 16-10
Mounting Adaptations - General Information ................................................................................................ 16-1
Service Tools.................................................................................................................................................. 16-3
Mounting Adaptations .................................................................................................................................. 16-3
ProCarManuals.com
Mounting Adaptations - General Information
Section 16 - Mounting Adaptations - Group 16 Page 16-1

General Information
The Mounting Adaptations group consists of the flywheel housing, flywheel, and the front engine support.
Flywheel Housing
For various applications, the flywheel housings are available in different styles, sizes, and materials. Check the
appropriate parts book and the engine parts listing for the correct part number for the engine application being serviced.
Flywheel and Ring Gear
The flywheel is available only as an assembly. The assembly includes the flywheel and the ring gear. The ring gear
is available for service.
Flywheel Housing — Redowel To The Cylinder Block
Procedure No. 016-006 Flywheel Housing — Redowel to Cylinder Block, will describe how to install the oversize locating
dowel pins in a flywheel housing and a cylinder block.
There are two dowel pins in the cylinder block. The pins protrude into holes in the flywheel housing. The pins are used
to align the housing properly to the cylinder block when it is installed.
The flywheel housing must be in proper alignment. If the housing is not in proper alignment, the holes in the flywheel
housing and the block must be reamed for a bigger dowel.
The dowel holes on QSK19 engine blocks and flywheel housings are precision doweled. The holes are machined to
12.7 mm [0.500 in] separately. The parts are assembled and the alignment is checked. If the alignment is not within
specifications, oversize dowels are installed at the factory. Replacing the block or the flywheel housing does not
ProCarManuals.com
necessarily mean that the flywheel housing and the cylinder block have to be redoweled.
Rail Applications
The rail engine front gear cover is manufactured out of cast
iron and has been machined to allow the front engine
mount to be installed on the cover.
Page 16-2 Section 16 - Mounting Adaptations - Group 16
Rail Applications
The flywheel housing has been modified to allow the en-
gine to be mounted horizontally (intake side down). The
intake side starter option in mandatory to keep a low profile
design for the railcar applications.
CAUTION
The flywheel housing, and the flywheel have metric
threads in the capscrew holes where the OEM hardware
will mount. The external mounting pads on the flywheel
housing have metric threads. Using the wrong
capscrews will damage the threads.
NOTE: A 75 degree mounting angle is available by using
the front mounting support and flywheel housing. If a 78
degree angle is desired, the OEM will be responsible for
modifying their engine supports to achieve a 78 degree tilt.
The QSK19 Rail Engine has two rock shields to protect the
intake side of the engine. The rock shields are mounted to
“T” shaped brackets. The brackets are mounted to the front
gear cover and lubricating oil pan adapter on the front of
the engine and the flywheel housing on the rear of the
engine. The rock shields extend the entire length of the
engine.
ProCarManuals.com
NOTE: The rock shields must be removed prior to working

on the intake side of the engine. Make certain they are
reinstalled after work is completed.
Service Tools
Service Tools
Mounting Adaptations

Dowel Pin Extractor
Remove dowel pins.
ST-1134
ProCarManuals.com
Drill Ream Fixture

ST-1232 priate drill/ream bushing set.
Engine Support Bracket

Attaches to the each side of the cylinder block and supports the
front of the engine.
3375272
Engine Lifting Fixture

Used to remove and install the engine. Designed to lift 1816 kg
[4000 lb].
3822512
Engine Support Bracket, Front (016-002)
Engine Support Bracket, Front

(016-002)
Clean
WARNING
sonal injury.
WARNING
personal injury.
Use solvent or steam to clean the engine support bracket.
Inspect for Reuse

CAUTION
ProCarManuals.com
component.
Clean and inspect the mounts for reuse. Check all rubber-
cushioned mounts for cracks or damage.
Inspect all mounting brackets for cracks or damaged bolt
holes.
NOTE: Damaged engine mounts and brackets can cause
the engine to move out of alignment, damage the driveline
components in the equipment, and result in vibration
complaints.
Flywheel (016-005)
Clean
WARNING
sonal injury.
WARNING
personal injury.
WARNING
Use solvent or steam to clean the flywheel.

Use a wire brush to clean the crankshaft pilot bore.
Flywheel (016-005)
Inspect for Reuse

Visually inspect for nicks or burrs. Use a crocus cloth to
remove small nicks and burrs.
WARNING
Do not use a cracked flywheel. A cracked flywheel can
break or cause serious personal injury.
Visually inspect the flywheel for cracks.
ProCarManuals.com
Visually inspect the flywheel ring gear teeth for cracks and
chips.
NOTE: If the ring gear teeth are cracked or broken, the ring
gear must be replaced.
Flywheel Housing (016-006)

Clean
WARNING
personal injury.
WARNING
sonal injury.
Use solvent or steam to clean the flywheel housing.
Inspect for Reuse

Visually inspect all surfaces for nicks, burrs, or cracks.
Use a fine crocus cloth to remove small nicks and burrs.
ProCarManuals.com
Visually inspect all threaded capscrew holes for damage.

Repair or replace the housing if the capscrew holes are
damaged.
Redowel
The tools needed to perform this procedure are:
Drill Ream Fixture, Part No. ST-1232, that contains:
1. Plate, Part No. ST-1232-1
2. Locator Pin, Part No. 3375052
3. Spacer Washer, Part No. ST-1232-2
4. Drill/Ream Bushing Set (Actual sizes depend on the
dowel size as listed in this Procedure.)
5. Drill Adapter (Locally obtained; use to adapt open (1)
shank reamers to drill-chuck)
6. Reamer (Locally obtained)
7. Drill Bit (Locally obtained)
Use a dowel pin extractor, Part No. ST-1134, or equivalent.

Remove the two dowels (9) from the block.
Measure a dowel pin that is removed so that an oversize
dowel pin can be determined.
ProCarManuals.com
NOTE: Do not torque the capscrews. The flywheel housing

must be aligned first.
Install the new rectangular seals (8) in the flywheel housing.
Align the flywheel housing to the crankshaft. for the pro-

cedure to measure the housing alignment.
Move the housing with a mallet until the bore is within
specification. Check to be sure that the face of the housing
is in alignment. When the housing is in alignment, tighten
the capscrews. for the capscrew torque.
After the capscrews are tightened, check the alignment
again.
Use the appropriate size capscrews. Attach the plate, Part

No. ST-1232-1, that is contained in Drill Ream Fixture, Part
No. ST-1232.
Hand-tighten the capscrews so the plate can be moved.
Use the locator pin to align the plate with the hole for the
dowel pin.
Tighten the capscrews. The taper on the pin must engage
the dowel pin hole.
The locator pin must rotate easily after the capscrews are
tightened.
CAUTION
ProCarManuals.com
Be sure the crankshaft is in the LOCKED position during

reaming to prevent damage.
Lock the crankshaft in position. Check to be sure the lo-
cator pin is still in alignment and that the locator pin can be
rotated easily.
Measure the dowel pins to be installed.

Obtain a reamer (5) that is 0.13 mm to 0.02 mm [0.005 in
to 0.001 in] smaller than the dowel.
The dowel must be long enough to protrude from the block
one-half of the flywheel housing wall thickness.
NOTE: There are three oversize dowel pins available from
Cummins Engine Company, Inc.
Oversize Dowel Pin O.D.
Overall Dimension Oversize
13.08 mm [0.515 in] 0.38 mm [0.015 in]
13.46 mm [0.530 in] 0.76 mm [0.030 in]
13.84 mm [0.545 in] 1.14 mm [0.045 in]
Install the appropriate drill bushings (4). The table shows

the bushings available from Cummins Engine Company,
Inc.
Drill/Ream Bushing Sets — 25.4 mm [1 Inch] O.D.
Oversize Bushing
Size
mm Inch mm Inch
3376495 Special 12.304 [0.4844]
Standard 12.700 [0.5000]
0.38 [0.015] 13.096 [0.5156]
0.76 [0.30] 13.494 [0.5312]
1.14 [0.045] 13.879 [0.5464]
ST-1234 Standard 14.288 [0.5625]

0.38 [0.015] 14.684 [0.5781]
0.76 [0.030] 15.081 [0.5937]
1.14 [0.045] 15.478 [0.6094]
ST-1235 Standard 15.875 [0.6250]

0.38 [0.015] 16.272 [0.6406]
0.76 [0.030] 16.669 [0.6562]
1.14 [0.045] 17.066 [0.6719]
ProCarManuals.com
ST-1236 Standard 17.463 [0.6875]

0.38 [0.015] 17.859 [0.7031]
0.76 [0.030] 18.256 [0.7187]
1.14 [0.045] 18.653 [0.7344]
ST-1237 Standard 19.050 [0.7500]

0.38 [0.015] 19.447 [0.7656]
0.76 [0.030] 19.844 [0.7812]
ST-1238 22.621 [0.8906]

23.813 [0.9375]
The drill bushing that is used must be the same size as the
reamer (or the drill) that is used.
If the new dowel pins are more than 0.38 mm [0.015 in]
larger than the old dowels, drill the hole to a size that is
slightly smaller than the reamer. Then the reamer will not
have to remove an excess amount of material.
CAUTION
Do not allow metal chips to enter the engine. Damage
to the engine will result.
Ream the hole until the reamer touches the bottom of the
hole in the block.
Remove the reamer.
Clean the hole and run the reamer through the hold again.
The reamer must touch the bottom of the hole in the block.
After reaming one hole, turn the plate and align it with the
second dowel hole. Repeat the procedure in the second
hole.
Flywheel Ring Gear (016-008)
Remove the plate from the crankshaft.

CAUTION
Be sure the dowel hole does not contain any metal
chips. Engine damage will result.
Use a square nose drift. Drive each dowel in until it touches
the bottom of the hole in the block.
After the dowels are installed, measure the bore and the
face alignment again.
ProCarManuals.com

Disassemble
CAUTION
burns.
CAUTION
Adjust the torch to a good heating flame. Do not use a
cutting flame (a blue flame) to heat the ring gear. Dam-
age to the flywheel can result.
Heat the ring gear.
Use a brass drift and a hammer to remove the hot ring gear.
If a heating torch is not available, the ring gear can be

removed with a brass drift and a hammer.
NOTE: If this method is used to remove the ring gear from
a flexplate assembly, be sure a wooden block is used to
support the ring gear adapter.
Assemble
CAUTION
burns.
CAUTION
Do not exceed the specified time or temperature. Dam-
age to the gear and to the gear teeth will result.
CAUTION
Damage or breakage will result.
Use an oven. Adjust the temperature to 232°C [450°F].
Heat the gear in the oven for a minimum of 1 hour, and a
maximum of 6 hours. The I.D. of the gear will become
larger and simplify the installation of the gear on the
flywheel.
CAUTION
burns.
Use a heating flame to heat the gear if an oven is not
ProCarManuals.com
available.
Use a TempilstikT crayon or equivalent, to check the tem-
perature of the gear.
Heat the gear to 232°C [450°F].
CAUTION
Do not exceed 316°C [600°F]. Damage to the ring gear
will result from the hardness of the metal being reduced.
CAUTION
burns.
Remove the gear from the oven.
Position the gear so the bevel is positioned toward the
crankshaft edge of the flywheel as shown.
The part number is on the same side as the bevel.
CAUTION
Allow the air to cool the gear. Do NOT use water or oil
to reduce the cooling time. Damage to the gear can
result.
Install the gear.
NOTES
ProCarManuals.com
Section 19 - Electronic Engine Controls - Group 19 Page 19-a
Section 19 - Electronic Engine Controls - Group 19

Section Contents
Page
Electronic Engine Controls - General Information ........................................................................................ 19-1
Connector Pins — Checking ............................................................................................................... 19-3
Continuity Check ................................................................................................................................. 19-7
How To Find The Internal Resistance of The Meter ............................................................................. 19-2
How To Measure Current ..................................................................................................................... 19-1
How To Measure Resistance ............................................................................................................... 19-2
How To Measure Voltage ..................................................................................................................... 19-2
How To Test For Continuity .................................................................................................................. 19-2
How To Use A Digital Volt/Ohm Meter ................................................................................................. 19-1
Polarity Check ..................................................................................................................................... 19-6
Resistance Check — Coil.................................................................................................................... 19-8
Short Circuit From Pin To Pin — Check............................................................................................... 19-5
Short Circuit To Ground — Check ....................................................................................................... 19-4
Use of Special Test Leads ................................................................................................................... 19-1
Voltage Checking ................................................................................................................................ 19-5
Engine Wiring Harness .................................................................................................................................. 19-8
OEM Interface Harness .................................................................................................................................. 19-9
ProCarManuals.com
OEM Wiring Harness...................................................................................................................................... 19-9

Electronic Engine Controls - General Information
Section 19 - Electronic Engine Controls - Group 19 Page 19-1
Electronic Engine Controls - General

Information
General Information
How To Use A Digital Volt/Ohm Meter
On most meters, the negative (black) meter lead must be
plugged in the “COM” position and the positive (red) meter
lead must be plugged into one of the positions marked for
current, resistance, or voltage. Refer to the manufacturer’s
instructions for more detail.
NOTE: When measuring to a block ground, use a clean
unpainted metal surface to ensure a good measurement.
NOTE: If more information is needed refer to the QSK19
Troubleshooting and Repair Manual, Bulletin No. 3666098.
Use of Special Test Leads

CAUTION
To avoid pin and harness damage, use the following test
leads when taking a measurement:
• Male Cannon, Metri-Pack and Deutsch test lead,
Part No. 3822758
ProCarManuals.com
• Female Amp, Metri-Pack and Deutsch test lead,

Part No. 3822917
• Male Deutsch test lead, Part No. 3823993
• Female Deutsch test lead, Part No. 3823994
• Male Weather-Pack test lead, Part No. 3823995
• Female Weather-Pack test lead, Part No. 3823996
How To Measure Current

Make an open circuit at the place where the current needs
to be measured.
Select the AC current (Az) or DC current (A−) function on
the meter.
Turn on the power in the circuit being measured.
Put the leads of the meter across the open circuit to mea-
sure the current.
Read the displayed measurement.
Page 19-2 Section 19 - Electronic Engine Controls - Group 19
How To Measure Voltage

Select the AC voltage (Vz) or DC voltage (V−) function on
the meter.
Turn on the power in the circuit being measured.
Put the leads of the meter in parallel with the component
to measure the voltage potential difference between the
two points of the component.
How To Measure Resistance

Select the resistance function on the meter.
Verify that there is no power to the components being
tested.
to measure resistance.
ProCarManuals.com
How To Find The Internal Resistance of The Meter

It is important to know the internal resistance of the meter
when measuring small resistances. To accurately measure
small resistances, the internal resistance of the meter must
be subtracted from the measured resistance.
Turn the meter “ON”.
Set the meter to the lowest ohm scale.
Measure the resistance across the meter test leads (in-
cluding special test leads if they are being used).
“ZERO” the meter or subtract this value when taking
measurements.
How To Test For Continuity

Select the continuity function on the meter (usually marked
with a diode symbol).
Make sure there is no power to the component being mea-
sured.
to test continuity.
The meter will beep if the resistance is less than about 150
Ohms. If there is an open circuit, the meter will not beep.
Connector Pins — Checking

When disconnecting connectors during troubleshooting,
the pins must always be inspected to make sure they are
not the cause of a bad connection. The three things to look
for are bent, corroded, and pushed back pins.
Bent Pins
Inspect the male terminals of the connector. If any of the
terminals are bent so that they will not easily mate with the
other side of the connector, then the pin must be replaced.
Refer to the connector repair section for the specific con-
nector in question.
ProCarManuals.com
Corroded Pins
Inspect both the male and female terminals for corrosion
which can cause a poor electrical connection within the
connector. If any corrosion is evident on the pins then the
corroded pins must be replaced. Refer to the connector
repair section for the specific connector in question.
Pushed Back Pins

Inspect both the male and female terminals for pins that
cannot be making contact because they are pushed back
in the connector. To repair, push the pin into the connector
body from the back of the connector. Make sure the ter-
minal locks into place. If the terminal will not lock into place
then replace it. Refer to the connector repair section for the
specific connector in question.
Short Circuit To Ground — Check

Short circuit to ground is a condition where a connection
from a wire to ground exists when it is not suppose to.
The procedure for checking for a short circuit to ground is
as follows:
Turn the key switch to the “OFF” position.
Disconnect the connectors that need to be tested. When
testing a sensor, the sensor connection only need be dis-
connected. When testing a harness, the harness connec-
tor at the ECM and the connector at the sensor or multiple
sensors will need to be disconnected.
Identify the pins that need to be tested.

Turn the dial on the digital VOM to measure resistance.
ProCarManuals.com
Use the appropriate test leads from the wiring harness

repair kit, Part No. 3822926, to avoid damage to the con-
nector pins.
Touch one of the VOM leads to the correct pin to be tested.
Touch the other lead of the VOM to the engine block.
Read the value on the VOM display.
The VOM must show greater than 100 K ohms which is an

open circuit.
If the circuit is not open, the wire being checked has a short
to ground or the engine block.
Repair or replace the component or wire.
Short Circuit From Pin To Pin — Check

Short circuit from pin to pin is a condition where an elec-
trical path exists between two pins where it is not suppose
to exist.
The procedure for checking short circuit from pin to pin is
as follows:
Disconnect the connector that needs to be tested.
Turn the dial on the digital VOM to measure resistance.

nector pins.
Touch one of the digital VOM leads to the correct pin to be
tested on the harness side of the connector.
Touch the other lead of the digital VOM to all other pins on
the harness side of this connector.
ProCarManuals.com

With the wiring harness disconnected from the ECM,
theVOM must show greater than 100 KΩ which is an open
circuit.
If the circuit is not open, the pins being checked are elec-
trically connected.
Inspect the harness connectors for water which can cause
an electrical connection.
Repair or replace the harness.
Voltage Checking
Voltage check is a procedure to measure the difference in
voltage potential between two points.
To check voltage, turn the key switch to the “ON” position.
Disconnect the connectors that need to be tested.
Turn the dial on the digital VOM to AC voltage (Vz) or DC
voltage (V-).

nector pins.
Touch one of the VOM test leads to the correct lead to be
tested.
Touch the other lead of the digital VOM to a clean unpainted
surface on the engine block.
Read the value on the VOM display. Compare the mea-

sured value to the range of voltage given in the specifica-
tions.
If the measured value falls outside of the specified range,
check the QSK Troubleshooting and Repair Manual, Bul-
letin No. 3666098, for the electrical system that is being
checked for the appropriate action.
ProCarManuals.com
Polarity Check
A battery will be used as an example to check polarity of
a circuit.
The terminals of a battery are marked for polarity. The
digital VOM displays the voltage difference of the positive
lead (red) to the negative lead (black).
The polarity is correct when the positive (red) lead of the

VOM is on the positive terminal of the battery and the
negative (black) lead of the VOM is on the negative terminal
of the battery.
The VOM will display positive voltage if the polarity is cor-
rect.
If the VOM leads are reversed, the VOM will display nega-
tive voltage.
Continuity Check
Continuity is an electrical connection between two pins that
is less than a certain resistance value. For harness wires,
the specification is less than 10 ohms.

Disconnect the harness connectors to be tested.
Turn the dial of the digital VOM to measure resistance.
ProCarManuals.com
CAUTION
repair kit, Part No. 3822926, to avoid damage to the
connector pins.
Touch one of the VOM test leads to the pin of the wire being
tested.
Touch the other lead of the VOM to the pin at the other end
of the wire being tested.
The VOM must display less than 10 ohms for wire conti-
nuity.
If the VOM displays greater than 10 ohms, the wire must
be repaired or the harness replaced.
Engine Wiring Harness (019-043)
Resistance Check — Coil

Disconnect the harness from the coil.
Turn the dial of the VOM to measure resistance.
CAUTION
repair kit, Part No. 3822926, to avoid damage to the
connector pins.
Touch one of the VOM leads to the coil connector pin.
Touch the other test lead to the other coil connector pin.
ProCarManuals.com
NOTE: For internally grounded coils, touch one VOM lead

to the coil terminal and the other VOM lead to the engine
block.
Read the measured resistance on the VOM display.
Check the measured resistance against the resistance

specification for the coil.
NOTE: The internal resistance of the VOM is significant in
some coil resistance checks.
Engine Wiring Harness (019-043)

Inspect for Reuse
Inspect the Engine Wiring Harness.
Check for any open or short circiuts in the wiring harness.
If any open or short circuits are found, the wiring harness
must be repaired or replaced.
OEM Wiring Harness (019-071)
OEM Wiring Harness (019-071)

General Information
The OEM harness is supplied and installed by the vehicle
manufacturer.
Follow the vehicle manufacturer’s instructions, if replace-
ment is necessary.
Refer to the vehicle manufacturer’s troubleshooting and
repair manual.
OEM Interface Harness (019-072)

General Information
The QSK equipped engines use three separate wiring har-
ness to control the engine and some of the vehicle opera-
tions.
1. Engine Harness
2. OEM Interface Harness
3. OEM Harness
ProCarManuals.com
Replace a harness if there is an open circuit or a short

circuit found under the protective covering of the harness
body.
OEM Interface Harness (019-072)
NOTES
ProCarManuals.com
QSK19
Section L - Service Literature Page L-a
Section L - Service Literature

Section Contents
Page
Additional Service Literature........................................................................................................................... L-1
Literature Order Form...................................................................................................................................... L-3
Service Literature Ordering Location.............................................................................................................. L-2
ProCarManuals.com
QSK19 Additional Service Literature
Section L - Service Literature Page L-1
Additional Service Literature

The following publications can be purchased by filling in and mailing the Literature Order Form:
Bulletin No. Title of Publication
3666098–01 Troubleshooting and Repair Manual QSK19 Series Engines
3885786 Users Guide Electronic Software and Database Network Version 3.1
3666120 Operation and Maintenance Manual QSK Fuel System/QSK19 Engine Series
3666133 QSK Fuel System Wiring/Fault Code Diagram
3666163 QSK Fuel System Echek™ 1.0 Cartridge Manual
3666148 INSITE™ For QSK Fuel System QUANTUM™ User’s Manual
3666113 Troubleshooting and Repair Manual QSK Fuel System/QSK19 Engine Series
3672094 QSK19 Parts Catalog - Construction
3666121 Holset Air Compressor Master Repair Manual
3898170 QUANTUM™ QSK19 Engine Familiarization
3898180 QUANTUM™ QSK19 Fuel System Familiarization
ProCarManuals.com
Service Literature Ordering Location QSK19
Page L-2 Section L - Service Literature
Service Literature Ordering Location

Region Ordering Location
United States and Canada Cummins Distributors
or
Contact 1-800-DIESELS
(1-800-343-7357)
U.K., Europe, Mid-East, Africa, Cummins Engine Co., Ltd.
and Eastern European Countries Royal Oak Way South
Daventry
Northants, NN11 5NU, England
South and Central America Cummins Americas, Inc.
(excluding Brazil and Mexico) 16085 N.W. 52nd Avenue
Hialeah, FL 33104
Brazil and Mexico Cummins Engine Co., Inc.
International Parts Order Dept., MC 40931
Box 3005
Columbus, IN 47202-3005
Far East (excluding Cummins Diesel Sales Corp.
Australia and New Zealand) Literature Center
8 Tanjong Penjuru
Jurong Industrial Estate
Singapore
Australia and New Zealand Cummins Diesel Australia
ProCarManuals.com
Maroondah Highway, P.O.B. 139

Ringwood 3134
Victoria, Australia
Obtain current price information from your local Cummins Distributor.
g-01 (loc)
QSK19 Literature Order Form
Section L - Service Literature Page L-3
Literature Order Form

Use this form for prompt handling of your literature order.
Bulletin Title of U.S. Price
Item Number Publication Quantity Each Amount
$ $
1
6
$
Order Total
Contact your Cummins distributor for prices and availability.

ProCarManuals.com
For problems with literature orders (for U.S.A. and Canada), contact 1-800-DIESELS (1-800-343-7357). All other
locations contact your local Distributor.
Prices subject to change without notice.
Please cut on dotted line

———————————————————————————————————————
Literature Order Form

Use this form for prompt handling of your literature order.
Bulletin Title of U.S. Price
Item Number Publication Quantity Each Amount
$ $
1
6
$
Order Total
Contact your Cummins distributor for prices and availability.

For problems with literature orders (for U.S.A. and Canada), contact 1-800-DIESELS (1-800-343-7357). All other
locations contact your local Distributor.
Prices subject to change without notice.
g-01 (f-order)
Literature Order Form QSK19
Page L-4 Section L - Service Literature
Mail the Literature Order Form along with your ship-to address to your nearest Cummins distributor.
FROM:
Name:
Street Address:
City: State/Province: Zip/Postal Code:
Country:
SHIP TO: (Name and address where literature is to be shipped)
Name:
Street Address:
ProCarManuals.com
Country:
Please cut on dotted line

———————————————————————————————————————
Mail the Literature Order Form along with your ship-to address to your nearest Cummins distributor.
FROM:
Name:
Street Address:
Country:
SHIP TO: (Name and address where literature is to be shipped)
Name:
Street Address:
Country:
g-01 (f-mail)
QSK19
Section M - Component Manufacturers Page M-a
Section M - Component Manufacturers

Section Contents
Page
Component Manufacturers’ Addresses .......................................................................................................... M-1
Air Compressors........................................................................................................................................... M-1
Air Cylinders ................................................................................................................................................ M-1
Air Heaters ................................................................................................................................................... M-1
Air Starting Motors ....................................................................................................................................... M-1
Alternators.................................................................................................................................................... M-1
Auxiliary Brakes ........................................................................................................................................... M-1
Belts............................................................................................................................................................. M-1
Catalytic Convertors ..................................................................................................................................... M-1
Clutches....................................................................................................................................................... M-1
Coolant Heaters ........................................................................................................................................... M-2
Coolant Level Switches ................................................................................................................................ M-1
Drive Plates.................................................................................................................................................. M-2
Electric Starting Motors ................................................................................................................................ M-2
Electronic Switches ...................................................................................................................................... M-2
Engine Protection Controls ........................................................................................................................... M-2
Fan Clutches ................................................................................................................................................ M-2
Fans............................................................................................................................................................. M-2
Fault Lamps ................................................................................................................................................. M-2
Filters........................................................................................................................................................... M-2
Flexplates..................................................................................................................................................... M-2
ProCarManuals.com
Fuel Coolers................................................................................................................................................. M-2

Fuel Warmers............................................................................................................................................... M-2
Gauges ........................................................................................................................................................ M-2
Governors .................................................................................................................................................... M-3
Heat Sleeves ................................................................................................................................................ M-3
Hydraulic and Power Steering Pumps........................................................................................................... M-3
In-Line Connectors ....................................................................................................................................... M-3
Oil Heaters ................................................................................................................................................... M-3
Prelubrication Systems ................................................................................................................................. M-3
Radiators...................................................................................................................................................... M-3
Throttle Assemblies ...................................................................................................................................... M-3
Torque Converters ........................................................................................................................................ M-3
QSK19 Component Manufacturers’ Addresses
Section M - Component Manufacturers Page M-1
Component Manufacturers’ Addresses

NOTE: The following list contains addresses and telephone numbers of suppliers of accessories used on Cummins
engines. Suppliers can be contacted directly for any specifications not covered in this manual.
Air Compressors StartMaster Belts

Air Starting Systems
Bendix Heavy Vehicles Systems A Division of Sycon Corporation Dayco Rubber U.K.
Div. of Allied Automotive 9595 Cheney Avenue Sheffield Street
901 Cleveland Street P. O. Box 491 Stockport
Elyria, OH 44036 Marion, OH 43302 Cheshire
Telephone: (216) 329-9000 Telephone: (614) 382-5771 SK4 1RV
Holset Engineering Co., Inc. England
1320 Kemper Meadow Drive Alternators Telephone: 061-432-5163
Suite 500 Robert Bosch Ltd. T.B.A. Belting Ltd.
Cincinnati, OH 45240 P.O. Box 98 P.O. Box 77
Telephone: (513) 825-9600 Broadwater Park Wigan
Midland-Grau North Orbital Road Lancashire
Heavy Duty Systems Denham WN2 4XQ
Heavy Duty Group Headquarters Uxbridge England
10930 N. Pamona Avenue Middlesex UD9 5HG Telephone: 01942-59221
Kansas City, MO 64153 England Dayco Mfg.
Telephone: (816) 891-2470 Telephone: 01895-833633 Belt Technical Center
Butec Electrics 1955 Enterprize
Air Cylinders Cleveland Road Rochester Hills, MI 48309
Bendix Ltd. Leyland Telephone: (810) 853-8300
ProCarManuals.com
Douglas Road PR5 1XB Gates Rubber Company

Kingswood England 900 S. Broadway
Bristol Telephone: 01744-21663 Denver, CO 80217
England C.A.V. Electrical Equipment
Telephone: 0117-671881 Goodyear Tire and
P.O. Box 36 Rubber Company
Catching Engineering Warple Way Industrial Products Div.
1733 North 25th Avenue London 2601 Fortune Circle East
Melrose Park, IL 60160 W3 7SS Indianapolis, IN 46241
Telephone: (708) 344-2334 England Telephone: (317) 898-4170
TEC - Hackett Inc. Telephone: 01-743-3111
8909 Rawles Avenue A.C. Delco Components Group Catalytic Convertors
Indianapolis, IN 46219 Civic Offices Donaldson Company, Inc.
Telephone: (317) 895-3670 Central Milton Keynes 1400 West 94th Street
MK9 3EL P.O. Box 1299
Air Heaters England Minneapolis, MN 55440
Fleetguard, Inc. Telephone: 01908-66001 Telephone: (612) 887-3835
1200 Fleetguard Road C. E. Niehoff & Co. Nelson Division
Cookeville, TN 38502 2021 Lee Street Exhaust and Filtration Systems
Telephone: (615) 526-9551 Evanston, IL 60202 1801 U.S. Highway 51 P.O. Box 428
Kim Hotstart Co. Telephone: (708) 866-6030 Stoughton, WI 53589
P.O. Box 11245 Delco-Remy America Telephone: (608) 873-4200
Spokane, WA 99211-0245 2401 Columbus Avenue Walker Manufacturing
Telephone: (509) 534-6171 P.O. Box 2439 3901 Willis Road
Anderson, IN 46018 P.O. Box 157
Air Starting Motors Telephone: (317) 646-3528 Grass Lake, MI 49240
Ingersoll Rand Leece-Neville Corp. Telephone: (517) 522-5500
Chorley New Road 400 Main Street
Horwich Arcade, NY 14009
Coolant Level Switches
Bolton Telephone: (716) 492-1700 Robertshaw Controls Company
Lancashire P.O. Box 400
England Auxiliary Brakes Knoxville, TN 37901
BL6 6JN Telephone: (216) 885–1773
Telephone: 01204-65544 The Jacobs Manufacturing Company
Vehicle Equipment Division Clutches
Ingersoll-Rand Engine 22 East Dudley Town Road
Starting Systems Bloomfield, CT 06002 Twin Disc International S.A.
888 Industrial Drive Telephone: (203) 243-1441 Chaussee de Namur
Elmhurst, IL 60126 Nivelles
Telephone: (708) 530-3875 Belguim
Telephone: 067-224941
g-01 (cmp-add)
Component Manufacturers’ Addresses QSK19
Page M-2 Section M - Component Manufacturers
Twin Disc Incorporated The Nason Company Fault Lamps

1328 Racine Street 2810 Blue Ridge Blvd.
Racine, WI 53403 West Union, SC 29696 Cutler-Hammer Products
Telephone: (414) 634-1981 Telephone: (803) 638-9521 Eaton Corporation
4201 N. 27th Street
Coolant Heaters Teddington Industrial Milwaukee, WI 53216
Equipment Telephone: (414) 449–6600
Fleetguard, Inc. Windmill Road
1200 Fleetguard Road Sunburn on Thames Filters
Cookeville, TN 38502 Middlesex
Telephone: (615) 526-9551 Fleetguard International Corp.
TW16 7HF Cavalry Hill Industrial Park
England
Drive Plates Telephone: 09327-85500
Weedon
Northampton NN7 4TD
Detroit Diesel Allison England
Division of General Motors Fan Clutches Telephone: 01327-41313
Corporation Holset Engineering Co. Ltd.
P.O. Box 894 P.O. Box A9 Fleetguard, Inc.
Indianapolis, IN 46206-0894 Turnbridge 1200 Fleetguard Road
Telephone: (317) 242-5000 Huddersfield, West Yorkshire Cookeville, TN 38502
England HD6 7RD Telephone: (615) 526-9551
Electric Starting Motors Telephone: 01484-22244
Butec Electrics
Flexplates
Horton Industries, Inc. Corrugated Packing and
Cleveland Road P.O. Box 9455
Leyland Sheet Metal
Minneapolis, MN 55440 Hamsterley
PR5 1XB Telephone: (612) 378-6410
England Newcastle Upon Tyne
Telephone: 01744-21663 Rockford Clutch Company England
1200 Windsor Road Telephone: 01207-560-505
ProCarManuals.com
C.A.V. Electrical Equipment P.O. Box 2908

P.O. Box 36 Allison Transmission
Rockford, IL 61132-2908 Division of General Motors
Warple Way Telephone: (815) 633-7460
London Corporation
W3 7SS Fans P.O. Box 894
England Indianapolis, IN 46206-0894
Telephone: 01-743-3111 Truflo Ltd. Telephone: (317) 242-5000
Westwood Road
A.C. Delco Components Group Birmingham Midwest Mfg. Co.
Civic Offices B6 7JF 29500 Southfield Road, Suite 122
Central Milton Keynes England Southfield, MI 48076
MK9 3EL Telephone: 021-557-4101 Telephone: (313) 642-5355
England Wohlert Corporation
Telephone: 0908-66001 Hayes-Albion Corporation
Jackson Manufacturing Plant 708 East Grand River Avenue
Delco-Remy America 1999 Wildwood Avenue P.O. Box 20217
2401 Columbus Avenue Jackson, MI 49202 Lansing, MI 48901
P.O. Box 2439 Telephone: (517) 782-9421 Telephone: (517) 485-3750
Anderson, IN 46018
Telephone: (317) 646-3528 Engineered Cooling Systems, Inc. Fuel Coolers
201 W. Carmel Drive Hayden, Inc.
Leece-Neville Corp. Carmel, IN 46032
400 Main Street 1531 Pomona Road
Telephone: (317) 846-3438 P.O. Box 848
Arcade, NY 14009
Telephone: (716) 492-1700 Brookside Corporation Corona, CA 91718–0848
P.O. Box 30 Telephone: (909) 736–2665
Nippondenso Inc. McCordsville, IN 46055
2477 Denso Drive Telephone: (317) 335-2014 Fuel Warmers
P.O. Box 5133 Fleetguard, Inc.
Southfield, MI 48086 TCF Aerovent Company
9100 Purdue Rd., Suite 101 1200 Fleetguard Road
Telephone: (313) 350-7500 Cookeville, TN 38502
Indianapolis, IN 46268-1190
Electronic Switches Telephone: (317) 872-0030 Telephone: (615) 526-9551
Cutler-Hammer Products Kysor-Cadillac Gauges

Eaton Corporation 1100 Wright Street
Cadillac, MI 49601 A.I.S.
4201 N. 27th Street Dyffon Industrial Estate
Milwaukee, WI 53216 Telephone: (616) 775-4681
Ystrad Mynach
Telephone: (414) 449–6600 Schwitzer Hengoed
6040 West 62nd Street Mid Glamorgan
Engine Protection Controls P.O. Box 80-B CF8 7XD
Flight Systems Headquarters Indianapolis, IN 46206 England
Hempt Road Telephone: (317) 328-3010 Telephone: 01443-812791
P.O. Box 25
Mechanicsburg, PA 17055
Telephone: (717) 697–0333
QSK19 Component Manufacturers’ Addresses
Section M - Component Manufacturers Page M-3
Grasslin U.K. Ltd. Heat Sleeves Kim Hotstart Co.

Vale Rise P.O. Box 11245
Tonbridge Bentley Harris Manufacturing Co. Spokane, WA 99211-0245
Kent 100 Bentley Harris Way Telephone: (509) 534-6171
TN9 1TB Gordonville, TN 38563
England Telephone: (313) 348-5779 Prelubrication Systems
Telephone: 01732-359888 Hydraulic and Power Steer- RPM Industries, Inc.
Icknield Instruments Ltd. ing Pumps Suite 109
Jubilee Road 55 Hickory Street
Letchworth Hobourn Automotive Washington, PA 15301
Herts Temple Farm Works Telephone: (412) 228–5130
England Priory Road
Telephone: 04626-5551 Strood Radiators
Rochester JB Radiator Specialties, Inc.
Superb Tool and Gauge Co. Kent, England
21 Princip Street P.O. Box 292087
ME2 2BD Sacramento, CA 95829–2087
Birmingham Telephone: 01634-71773
B4 61E Telephone: (916) 381–4791
England Honeywell Control Systems Ltd. The G&O Manufacturing Company
Telephone: 021-359-4876 Honeywell House 100 Gando Drive
Charles Square P.O. Box 1204
Kabi Electrical and Plastics Bracknell
Cranborne Road New Haven, CT 06505–1204
Berks RG12 1EB Telephone: (203) 562–5121
Potters Bar Telephone: 01344-4245
Herts Young Radiator Company
EN6 3JP Sundstrand Hydratec Ltd. 2825 Four Mile Road
England Cheney Manor Trading Estate Racine, WI 53404
Telephone: 01707-53444 Swindon Telephone: (910) 271–2397
Wiltshire
ProCarManuals.com
Datcon Instruments SN2 2PZ L and M Radiator, Inc.

P.O. Box 128 England 1414 East 37th Street
East Petersburg, PA 17520 Telephone: 01793-30101 Hibbing, MN 55746
Telephone: (717) 569-5713 Telephone: (218) 263–8993
Sperry Vickers
Rochester Gauges, Inc. P.O. Box 302 Throttle Assemblies
11616 Harry Hines Blvd. Troy, MI 48084
P.O. Box 29242 Telephone: (313) 280-3000 Williams Controls, Inc.
Dallas, TX 75229 14100 SW 72nd Avenue
Telephone: (214) 241-2161 Z.F. Portland, OR 97224
P.O. Box 1340 Telephone: (503) 684–8600
Governors Grafvonsoden Strasse
Woodward Governors Ltd.
5-9 D7070 Torque Converters
Schwaebisch Gmuend Twin Disc International S.A.
P.O. Box 15 Germany
663/664 Ajax Avenue Chaussee de Namur
Telephone: 7070-7171-31510 Nivelles
Slough
Bucks In-Line Connectors Belgium
SL1 4DD Telephone: 067-224941
England Pioneer-Standard Electronics, Inc.
5440 Neiman Parkway Twin Disc Incorporated
Telephone: 01753-26835 1328 Racine Street
Solon, OH 44139
Woodward Governor Co. Telephone: (216) 349–1300 Racine, WI 53403-1758
P.O. Box 1519 Telephone: (414) 634-1981
Fort Collins, CO 80522 Deutsch
Industrial Products Division Rockford Powertrain, Inc.
Telephone: (303) 482-5811 Off-Highway Systems
(800) 523-2831 37140 Industrial Avenue
Hemet, CA 92343 1200 Windsor Road
Barber Colman Co. Telephone: (714) 929–1200 P.O. Box 2908
1354 Clifford Avenue Rockford, IL 61132-2908
Loves Park, IL 61132 Oil Heaters Telephone: (815) 633-7460
Telephone: (815) 637-3000 Fleetguard, Inc. Modine Mfg. Co.
United Technologies 1200 Fleetguard Road 1500 DeKoven Avenue
Diesel Systems Cookeville, TN 38502 Racine, WI 53401
1000 Jorie Blvd. Telephone: (615) 526-9551 Telephone: (414) 636-1640
Suite 111
Oak Brook, IL 69521
Telephone: (312) 325-2020
Component Manufacturers’ Addresses QSK19
Page M-4 Section M - Component Manufacturers
NOTES
ProCarManuals.com
QSK
Section V - Specifications Page V-a
Section V - Specifications
Section Contents
Page
Air Intake System - Specifications ................................................................................................................ V-42
Aftercooler Assembly .................................................................................................................................. V-42
Turbocharger, Water-Cooled ........................................................................................................................ V-42
Air Intake System - Torque Values ................................................................................................................ V-43
Aftercooler Assembly .................................................................................................................................. V-43
Turbocharger Heat Shield............................................................................................................................ V-43
Cam Followers/Tappets - Specifications ....................................................................................................... V-24
Cam Follower Assembly .............................................................................................................................. V-24
Capscrew Markings and Torque Values ........................................................................................................ V-48
Capscrew Markings and Torque Values - Metric ......................................................................................... V-49
Capscrew Markings and Torque Values - U.S. Customary .......................................................................... V-50
Complete Engine - Specifications .................................................................................................................. V-1
Engine Assembly .......................................................................................................................................... V-1
Complete Engine - Torque Values................................................................................................................... V-3
Engine Assembly .......................................................................................................................................... V-3
Engine Disassembly ..................................................................................................................................... V-3
Cooling System - Specifications ................................................................................................................... V-31
Fan Drive Idler Pulley Assembly .................................................................................................................. V-31
ProCarManuals.com
Fan Hub, Belt Driven ................................................................................................................................... V-31

Torque Converter Cooler ............................................................................................................................. V-31
Water Pump ................................................................................................................................................ V-31
Water Pump Bearings ................................................................................................................................. V-32
Cooling System - Torque Values ................................................................................................................... V-33
Coolant Thermostat..................................................................................................................................... V-33
Fan Hub, Belt Driven................................................................................................................................... V-33
Torque Converter Cooler ............................................................................................................................. V-34
Water Pump ................................................................................................................................................ V-34
Cylinder Block - Specifications..................................................................................................................... V-13
Bearings, Main............................................................................................................................................ V-13
Camshaft .................................................................................................................................................... V-13
Camshaft Bushings..................................................................................................................................... V-13
Camshaft Gear (Camshaft Removed) .......................................................................................................... V-13
Connecting Rod .......................................................................................................................................... V-14
Crankshaft .................................................................................................................................................. V-15
Crankshaft Gear, Front (Crankshaft Installed) .............................................................................................. V-15
Crankshaft Pulley ........................................................................................................................................ V-15
Cylinder Block............................................................................................................................................. V-15
Cylinder Block and Liner Seats ................................................................................................................... V-15
Cylinder Block Counterbore ........................................................................................................................ V-18
Cylinder Liner ............................................................................................................................................. V-16
Gear Cover Accessory Drive Bushing.......................................................................................................... V-18
Gear Cover, Front........................................................................................................................................ V-17
Gear Cover Spacer Plate ............................................................................................................................ V-17
Idler Gear, Camshaft ................................................................................................................................... V-17
Measure the Connecting Rod Bend (Bore Alignment).................................................................................. V-14
Measure the Connecting Rod Twist ............................................................................................................. V-15
Piston ......................................................................................................................................................... V-17
Cylinder Block - Torque Values ..................................................................................................................... V-19
Connecting Rod .......................................................................................................................................... V-19
Crankshaft Pulley ........................................................................................................................................ V-19
Cylinder Block............................................................................................................................................. V-19
Cylinder Block Counterbore ........................................................................................................................ V-19
Cylinder Head - Specifications...................................................................................................................... V-20
Cylinder Head ............................................................................................................................................. V-20
Cylinder Head Injector Bore ........................................................................................................................ V-20
Valve, Cylinder Head ................................................................................................................................... V-21
Valve Guide, Cylinder Head ........................................................................................................................ V-20
QSK
Page V-b Section V - Specifications
Page
Valve Seat Bore........................................................................................................................................... V-21
Valve Seat Insert, Cylinder Head ................................................................................................................. V-21
Drive Belt Tension ......................................................................................................................................... V-47
Drive Units - Specifications........................................................................................................................... V-35
Fuel Pump Drive ......................................................................................................................................... V-35
Fuel Pump Drive Gear and Shaft ................................................................................................................ V-36
Hydraulic Pump Drive ................................................................................................................................. V-36
Hydraulic Pump Support Bushing ............................................................................................................... V-39
Outer Hydraulic Pump Support Drive .......................................................................................................... V-38
Rear Gear Drive (Lower Assembly).............................................................................................................. V-36
Rear Gear Drive (Upper Assembly) ............................................................................................................. V-37
Water Pump Drive....................................................................................................................................... V-38
Drive Units - Torque Values ........................................................................................................................... V-40
Outer Hydraulic Pump Support Drive .......................................................................................................... V-41
Rear Gear Drive (Lower Assembly).............................................................................................................. V-40
Rear Gear Drive (Upper Assembly) ............................................................................................................. V-40
Electrical Equipment - Specifications........................................................................................................... V-45
Drive Belt, Alternator................................................................................................................................... V-45
Engine Testing - Specifications..................................................................................................................... V-46
Engine Testing (Chassis Dynamometer) ...................................................................................................... V-46
Engine Testing (Engine Dynamometer)........................................................................................................ V-46
Exhaust System - Specifications .................................................................................................................. V-44
ProCarManuals.com
Exhaust Manifold, Dry................................................................................................................................. V-44

Fraction, Decimal, Millimeter Conversions ................................................................................................... V-51
Fuel System - Torque Values......................................................................................................................... V-25
Fuel Shutoff Valve (FSOV) ........................................................................................................................... V-25
Injectors and Fuel Lines - Torque Values...................................................................................................... V-26
Fuel Manifold (Supply) ................................................................................................................................ V-26
Lubricating Oil System - Specifications........................................................................................................ V-27
Lubricating Oil Filter Head .......................................................................................................................... V-27
Lubricating Oil Filter Head (LF670).............................................................................................................. V-27
Lubricating Oil Filter Head (Remote-Mounted) ............................................................................................. V-27
Lubricating Oil Pan ..................................................................................................................................... V-27
Lubricating Oil Pump .................................................................................................................................. V-27
Oil Transfer Connection............................................................................................................................... V-28
Lubricating Oil System - Torque Values ........................................................................................................ V-29
Lubricating Oil Cooler ................................................................................................................................. V-29
Lubricating Oil Filter Head .......................................................................................................................... V-29
Lubricating Oil Filter Head (Remote-Mounted) ............................................................................................. V-29
Lubricating Oil Pump .................................................................................................................................. V-29
Oil Transfer Connection............................................................................................................................... V-30
Newton-Meter to Foot-Pound Conversion Chart ........................................................................................... V-52
Pipe Plug Torque Values................................................................................................................................ V-53
Rocker Levers - Specifications...................................................................................................................... V-23
Rocker Lever............................................................................................................................................... V-23
Rocker Lever Assembly............................................................................................................................... V-23
Rocker Lever Bushings ............................................................................................................................... V-23
Tap-Drill Chart - U.S. Customary and Metric ................................................................................................ V-54
Weights and Measures - Conversion Factors ............................................................................................... V-55
QSK Complete Engine - Specifications
Section V - Specifications Page V-1
Component or Assembly (Procedure) Ref.No./Steps Metric U.S.
Complete Engine - Specifications

Cylinder Liner I.D. (New) 158.737 mm MIN 6.2495 in
158.775 mm MAX 6.2510 in
Cylinder Liner Protrusion 0.13 mm MIN 0.003 in

0.18 mm MAX 0.007 in
Crankshaft End Clearance 0.10 mm MIN 0.004 in

0.41 mm MAX 0.016 in
ProCarManuals.com
Connecting Rod and Crankshaft Side

Clearance New or Remanufactured Parts 0.20 mm MIN 0.008 in
0.35 mm MAX 0.014 in
Camshaft End Clearance 0.15 mm MIN 0.006 in

0.33 mm MAX 0.013 in
Hydraulic Pump Idler Gear End Clearance 0.10 mm MIN 0.004 in

0.36 mm MAX 0.014 in
Water Pump Idler Gear End Clearance 0.10 mm MIN 0.004 in

0.36 mm MAX 0.014 in
Complete Engine - Specifications QSK
Page V-2 Section V - Specifications
Camshaft Idler Gear End Clearance 0.29 mm MIN 0.012 in

0.51 mm MAX 0.020 in
Lower Housing-To-Cylinder Block Gear

Backlash 0.05 mm MIN 0.002 in
0.51 mm MAX 0.015 in
Idler Gear Backlash 0.05 mm MIN 0.002 in

0.51 mm MAX 0.020 in
ProCarManuals.com
Piston Cooling Nozzle Mounting Capscrew

Torque Value 45 N•m 35 ft-lb

Reference mm in
Point
A 0.81 Exhaust 0.032
B 0.36 Intake 0.014
Aftercooler Hose Clamp Torque Value 6 N•m 50 in-lb
Alternator Belt Tension 670 N 150 lbf

QSK Complete Engine - Torque Values
Complete Engine - Torque Values

Engine Disassembly (009-029)
Engine Stand Mounting Capscrews 45 N•m 35 ft-lb

Main Bearing Cap Bolts 1 265 N•m 195 ft-lb
2 605 N•m 445 ft-lb
3 Loosen Loosen
4 265 N•m 195 ft-lb
5 605 N•m 445 ft-lb
Connecting Rod Capscrews 1 100 N•m 75 ft-lb

2 205 N•m 150 ft-lb
3 339 N•m 250 ft-lb
4 Loosen Loosen
5 100 N•m 75 ft-lb
ProCarManuals.com
6 205 N•m 150 ft-lb

7 339 N•m 250 ft-lb
Oil Suction Tube Mounting Capscrews 60 N•m 25 ft-lb

35 N•m 25 ft-lb
Gear Cover Spacer Plate Capscrews 45 N•m 35 ft-lb
Idler Gear 245 N•m 180 ft-lb
Lube Oil Pump Idler Gear 245 N•m 180 ft-lb

Complete Engine - Torque Values QSK
Camshaft Idler Gear Install

Camshaft Idler Gear Mountig Capscrew 1 45 N•m 35 ft-lb
2 95 N•m 70 ft-lb
3 150 N•m 110 ft-lb
Flywheel Housing Mounting Capscrews 1 100 N•m 75 ft-lb

2 205 N•m 150 ft-lb
Lube Oil Pan Adapter Mounting Capscrews

3/8-16 inch 45 N•m 35 ft-lb
7/16-14 inch 65 N•m 50 ft-lb
ProCarManuals.com
Rear Main Seal Mounting Capscrews 11 N•m 95 in-lb
Oil Pan Adapter Capscrews

Capscrews 1 – 23 60 N•m 45 ft-lb
Oil Pan Adapter Capscrews
Capscrews 24 – 28 45 N•m 35 ft-lb
Front Engine Mount 195 N•m 145 ft-lb
Lube Oil Pan Mounting Capscrews 45 N•m 35 ft-lb

Air Compressor Mounting Capscrews

Capscrew 5 60 N•m 45 ft-lb
Cylinder Head Capscrews Step 1 68 N•m 50 ft-lb

Step 2 205 N•m 150 ft-lb
3 300 N•m 220 ft-lb
4 Rotate 90 Degrees
Rocker Lever Housing Sequence Torque 95 N•m 70 ft-lb

ProCarManuals.com
Valve Adjusting Screw 1 N•m 6 in-lb
Valve Set-Feel Method

With Torque Wrench Adapter, Part No.
ST-669 (1) 45 N•m 35 ft-lb
Without Adapter 60 N•m 45 ft-lb
Valve Adjusting Screw Locknut 20 N•m 250 in-lb

Valve Adjusting Screw 19 N•m 165 in-lb
Rocker Lever Cover Capscrews 45 N•m 35 ft-lb

Thermostat Housing Support Capscrews 45 N•m 35 ft-lb
Capscrew 20 N•m 15 ft-lb

Hose Clamp 6 N•m 50 in-lb
Aftercooler Coolant Return Tube

Capscrews 6 N•m 50 in-lb
ProCarManuals.com




Cam Follower Mounting Capscrews 1 55 N•m 40 ft-lb

2 110 N•m 80 ft-lb
3 165 N•m 120 ft-lb
Cam Follower Cover Capscrews 27 N•m 20 ft-lb
Filter Head Capscrews 45 N•m 35 ft-lb

ProCarManuals.com
Accessory Drive Capscrews 45 N•m 35 ft-lb
O-Ring Plugs 25 N•m 20 ft-lb
Fuel Pump Capscrews 45 N•m 35 ft-lb
Fuel Pump Inlet Hose 88 N•m 65 ft-lb

Fuel Supply Hose 60 N•m 45 ft-lb
Fuel Control Valve Body Assembly

Electrical Connection Post 3 N•m 25 in-lb
Electrical Connection Nut 2 N•m 15 in-lb

ProCarManuals.com
Control Valve Body Hoses

Fuel Supply Hose (1) 61 N•m 45 ft-lb
Timing and Rail Pressure Lines (2 and 3) 27 N•m 20 ft-lb
Front Fuel Manifold Capscrews 9.6 N•m 85 in-lb
Fuel Tube Nut 27 N•m 20 ft-lb
Air Inlet Connection Hose

Flange Capscrew: 4 N•m 35 in-lb
Clamp: 6 N•m 50 in-lb
Aftercooler Capscrews Step 1 25 N•m 20 ft-lb

2 45 N•m 35 ft-lb
Turbocharger Oil Return Line 45 N•m 35 ft-lb
Rail Applications, Air Crossover Clamp 8 N•m 75 in-lb

ProCarManuals.com
Oil Cooler Element Capscrews 45 N•m 35 ft-lb
Torque Converter Cooler Cover Capscrews 45 N•m 35 ft-lb
Aftercooler Supply Hose Clamp 5.6 N•m 50 in-lb
Torque Converter Cooler Bypass Tube

Clamp 5.6 N•m 50 in-lb
Oil Cooler Cover Capscrews 45 N•m 35 ft-lb
Water Pump Outlet Connection Capscrews 45 N•m 35 ft-lb
Water Pump Outlet Connection Hose

Clamps 6 N•m 50 in-lb
ProCarManuals.com
Exhaust Manifold Capscrews 45 N•m 35 ft-lb
Turbocharger Capscrews 40 N•m 30 ft-lb
Bearing Housing Capscrews 20 N•m 180 in-lb
Oil Supply Hose Fitting 31 N•m 23 ft-lb

Turbocharger Inlet Piping Clamp 8 N•m 75 in-lb
Turbocharger Exhaust Piping Clamp 8 N•m 75 in-lb
Belt Tensioner Capscrews 201 N•m 75 ft-lb

ProCarManuals.com
Idler Arm Assembly Capscrews 45 N•m 35 ft-lb
Fan Hub Nuts 34 N•m 25 ft-lb
Water Pump Inlet Connection Capscrews 40 N•m 30 ft-lb
Warer Pump Mounting Capscrews and Nut 45 N•m 35 ft-lb

Water Pump Support Bracket Capscrew 206 N•m 150 ft-lb
Alternator Pulley Nut 100 N•m 75 ft-lb
Belt Tensioning
Jam Nuts 55 N•m 40 ft-lb
Alternator Mounting Capscrews 55 N•m 40 ft-lb
ProCarManuals.com
Starting Motor Mounting Capscrews

W/Cast Iron Flywheel Housing 215 N•m 160 ft-lb
W/Aluminum Flywheel Housing 195 N•m 145 ft-lb
QSK Cylinder Block - Specifications
Cylinder Block - Specifications

Bearings, Main (001-006)
Standard 3.82 mm MIN 0.1505 in
3.90 mm MAX 0.1535 in
0.010 (OS) 4.08 mm MIN 0.1605 in
4.15 mm MAX 0.1635 in
0.020 (OS) 4.33 mm MIN 0.1705 in
4.41 mm MAX 0.1735 in
Camshaft (001-008)
Camshaft Bushing Journal O.D. 76.07 mm MIN 2.995 in
76.12 mm MAX 2.997 in
Camshaft Bushing I.D. 82.550 mm MIN 3.2500 in

82.640 mm MAX 2.2535 in
ProCarManuals.com

Camshaft O.D. (Gear Location) 57.200 mm MIN 2.2520 in
57.210 mm MAX 2.2525 in
Camshaft Gear I.D. 57.200 mm MIN 2.2520 in

57.210 mm MAX 2.2525 in
Camshaft to Camshaft Gear Clearance 0.15 mm MIN 0.006 in

0.33 mm MAX 0.013 in

Camshaft Bushing Bore I.D. 88.989 mm MIN 3.5035 in
89.015 mm MAX 3.5045 in
Cylinder Block - Specifications QSK
Camshaft Bushing I.D. 82.550 mm MIN 3.2500 in

82.640 mm MAX 2.2535 in

Capscrew Length (1) 117.09 mm MIN 4.610 in
117.86 mm MAX 4.640 in
Capscrew O.D. (2) 15.26 mm MIN 0.601 in
15.37 mm MAX 0.605 in
Capscrew O.D. (3) 17.35 mm MIN 0.683 in
17.45 mm MAX 0.687 in
Connecting Rod Wrist Pin Bearing I.D. 60.99 mm MIN 2.4010 in

61.02 mm MAX 2.4025 in
ProCarManuals.com
Connecting Rod Bearing Bore I.D. 107.995 mm MIN 4.2518 in

108.005 mm MAX 4.2522 in
Connecting Rod Length 289.69 mm MIN 11.405 in

289.74 mm MAX 11.407 in
Measure the Connecting Rod Bend (Bore Alignment)

Connecting Rod Bend
0.010 mm MAX 0.004 in
0.195 mm MAX 0.008 in
Measure the Connecting Rod Twist

Maximum Connecting Rod Twist
Bushing Installed 0.25 mm MAX 0.010 in
Bushing Removed 0.51 mm MAX 0.020 in
Crankshaft O.D.
Location (1) 152.35 mm MIN 5.998 in
152.40 mm MAX 6.000 in
111.13 mm MAX 4.375 in
110.77 mm MAX 4.361 in
Rod Bearing Journal O.D. (4) 101.524 mm MIN 3.997 in

101.600 mm MAX 4.000 in
Main Bearing Journal O.D. (5) 139.637 mm MIN 5.4975 in
139.700 mm MAX 5.5000 in
ProCarManuals.com
Thrust Distance (6) 60.30 mm MIN 2.374 in

60.33 mm MAX 2.375 in

Crankshaft O.D. (Gear Location) 111.25 mm MIN 4.380 in
111.28 mm MAX 4.381 in

Pully O.D. 134.78 mm MIN 5.3105 in
135.04 mm MAX 5.3115 in
Pully I.D. 110.780 mm MIN 4.3610 in
110.806 mm MAX 4.3620 in

(13) Cylinder Block Height 481.91 mm MIN 18.9735 in
482.76 mm MAX 19.0065 in
(14) Cylinder Block Height- Main bearing
Saddle 407.70 mm MIN 16.051 in
408.53 mm MAX 16.084 in

Counterbore Depth 13.755 mm MIN 0.5415 in
13.805 mm MAX 0.5435 in
Counterbore Diameter - UPPER Press Fit

Diameter 188.16 mm MIN 7.409 in
188.21 mm MAX 7.410 in
Counterbore Diameter - LOWER Press Fit

Diameter 180.09 mm MIN 7.090 in
180.14 mm MAX 7.092 in
(4) Packing Ring Bore 177.34 mm MIN 6.982 in

177.40 mm MAX 6.984 in
ProCarManuals.com

Cylinder Liner I.D. 158.737 mm MIN 6.2495 in
158.877 mm MAX 6.2550 in
Upper Press Fit Liner Flange Diameter

188.24 mm MAX 7.411 in
Oversize 20/20 188.70 mm MIN 7.429 in
188.75 mm MAX 7.431 in
Lower Press Fit Area O.D.

180.21 mm MAX 7.095 in
Oversize 20/20 180.67 mm MIN 7.113 in
180.72 mm MAX 7.115 in
Liner Flange Thickness 13.398 mm MIN 0.5275 in

13.424 mm MAX 0.5285 in

Accessory Drive Stud (1)- Installed Height 31.88 mm MIN 1.255 in
33.15 mm MAX 1.305 in
Water Pump Drive Stud (2) — Installed
Height Gear Spacer Plate and Gear
Housing 62.99 mm MIN 2.480 in
63.75 mm MAX 2.510 in

Accessory Drive & Water Pump Drive
Bushing I.D. 39.75 mm MIN 1.565 in
39.90 mm MAX 1.571 in
Hydraulic Pump Drive (2) Bushing I.D. 38.13 mm MIN 1.501 in
38.25 mm MAX 1.506 in
Barring Mechanism Bushing Bore 18.215 mm MIN 0.717 in

18.265 mm MAX 0.719 in
ProCarManuals.com

Idler Gear Bushing I.D. 47.638 mm MIN 1.8755 in
47.714 mm MAX 1.8785 in
Piston (001-043)
Ring Groove Wear Limits (Diameter Over
Pins)
Top Ring 159.100 mm MIN 6.2638 in
Second Ring 159.413 mm MIN 6.2761 in
Piston Oil Ring Groove Width 4.788 mm MIN 0.1885 in

4.851 mm MAX 0.1910 in
Articulated Piston Pin Bore I.D. (Crown) 60.960 mm MIN 2.4000 in

61.059 mm MAX 2.4039 in
Articulated Piston Pin Bore I.D. (Skirt) 60.949 mm MIN 2.3996 in
60.961 mm MAX 2.4000 in
Piston Pin O.D. 60.929 mm MIN 2.3988 in

60.935 mm MAX 2.3990 in
Piston Pin Length 132.59 mm MIN 5.220 in
132.85 mm MAX 5.230 in

Cylinder Liner Protrusion 0.13 mm MIN 0.003 in
0.18 mm MAX 0.007 in
Liner Bore Run Out 0.130 mm MAX 0.005 in

ProCarManuals.com
Gear Cover Accessory Drive Bushing (001-066)

Front Cover Bushing Bore I.D.
Accessory and Water Pump Drive 43.078 mm MIN 1.696 in
43.104 mm MAX 1.697 in
Hydraulic Pump Drive 41.275 mm MIN 1.625 in
41.301 mm MAX 1.626 in
QSK Cylinder Block - Torque Values
Cylinder Block - Torque Values

Vibration Damper 140 N•m 105 ft-lb


Cylinder Block Counter Bore Mechining
Tool 40 N•m 30 ft-lb
40 N•m 30 ft-lb
ProCarManuals.com

Connecting Rod Capscrew
1 100 N•m 75 ft-lb
2 200 N•m 150 ft-lb
3 290 N•m 214 ft-lb
Loosen
Connecting Rod Capscrew
5 100 N•m 75 ft-lb
6 200 N•m 150 ft-lb
7 290 N•m 214 ft-lb
Cylinder Head - Specifications QSK
Cylinder Head - Specifications

Cylinder Head (002-004)
Allowable Crack Length 6 mm MAX 0.25 in
Allowable Valve Depth from the

Combustion Face 0.00 mm MIN 0.000 in
0.51 mm MAX 0.020 in
Minimum Head Thickness (1) 150.114 mm MIN 5.910 in

ProCarManuals.com
Cylinder Head Capscrew Free Length 207.3 mm MAX 8.160 in
Cylilnder Head Pressure Test–Air Pressure 552 kPa MAX 80 psi
Cylinder Head Injector Bore (002-011)

Injector Protrusion 2.42 mm MIN 0.095 in
2.92 mm MAX 0.115 in
Valve Guide, Cylinder Head (002-017)

Valve Guide I.D. (Installed) 10.551 mm MIN 0.4154 in
10.589 mm MAX 0.4169 in
QSK Cylinder Head - Specifications
Valve Guide Bore I.D. 21.438 mm MIN 0.8440 in

21.463 mm MAX 0.8450 in
Valve Guide Height (to Spring Pocket) 37.97 mm MIN 1.495 in

38.48 mm MAX 1.515 in
Valve Guide Height (to Top of Head) 13.97 mm MIN 0.550 in
14.47 mm MAX 0.570 in
Valve Seat Bore (002-018)

Valve Seat Bore Measurements
Intake Diameter 60.37 mm MIN 2.377 in
60.40 mm MAX 2.378 in
Intake Depth 13.00 mm MIN 0.492 in
ProCarManuals.com
13.13 mm MAX 0.497 in

Exhaust Diameter 60.37 mm MIN 2.377 in
60.40 mm MAX 3.378 in
Exhaust Depth 12.50 mm MIN 0.492 in
12.62 mm MIN 0.497 in
Valve Seat Insert, Cylinder Head (002-019)
Valve Seat Width
Intake 3.05 mm MIN 0.120 in
3.55 mm MAX 0.140 in
Exhaust 1.52 mm MIN 0.060 in
2.54 mm MAX 0.100 in
Valve Seat to Guide Concentricity 0.05 mm MAX 0.002 in
Valve, Cylinder Head (002-020)

Valve Stem O.D. 10.490 mm MIN 0.4130 in
10.510 mm MAX 0.4138 in
Valve Head Thickness (at the O.D.) 3.94 mm MIN 0.155 in

Cylinder Head - Specifications QSK
Coil Shot Amperage
Coil Shot Amperage

(Ampere Turns)
Head Shot Amperage
Head Shot Amperage

(Ampere)
ProCarManuals.com
QSK Rocker Levers - Specifications
Rocker Levers - Specifications



Rocker Arm Shaft O.D. 47.592 mm MIN 1.8737 in
47.634 mm MAX 1.8753 in
Bushing Bore I.D. 47.66 mm MIN 1.876 in

47.73 mm MAX 1.879 in
ProCarManuals.com

Lever Bore I.D. 49.25 mm MIN 1.939 in
49.27 mm MAX 1.940 in
Cam Followers/Tappets - Specifications QSK
Cam Followers/Tappets - Specifications

Cam Follower Shaft O.D. 28.538 mm MIN 1.1235 in
28.575 mm MAX 1.125 in

Reference Point mm in
(1) 0.230 MIN 0.009
0.610 MAX 0.024
(2) 0.076 MIN 0.003

0.114 MAX 0.0045
Cam Follower Lever I.D. 28.611 mm MIN 1.1264 in

28.661 mm MAX 1.1284 in
ProCarManuals.com
QSK Fuel System - Torque Values
Fuel System - Torque Values

3 N•m 25 in-lb
8 N•m 72 in-lb
2 N•m 15 in-lb
ProCarManuals.com
Injectors and Fuel Lines - Torque Values QSK
Injectors and Fuel Lines - Torque Values

Manifold Plugs
Plug (1): 20 N•m 180 in-lb
Plug (2): 7 N•m 60 in-lb
Fuel Connection Block 10 N•m 90 in-lb

ProCarManuals.com
QSK Lubricating Oil System - Specifications
Lubricating Oil System - Specifications

Free Length 88.98 mm MIN 3.500 in
Working Height (6) 50.80 mm MAX 2.000 in
Spring Force (7) 26 N•m MIN 19.3 ft-lb
29 N•m MAX 21.3 ft-lb
Lubricating Oil Filter Head (LF670) (007-015)

LF670 Filter Head Adapter 88 N•m
65 ft-lb

Free Length 88.98 mm MAX 3.500 in
ProCarManuals.com

29 mm MAX 21.3 in

Oil Pan Capacities
Shallow full length 49 liters MIN 13 U.S.gal
PN 3086097 61 liters MAX 16 U.S.gal
Long (1/3) deep 49 liters MIN 13 U.S.gal
Short (1/3) deep 49 liters MIN 13 U.S.gal
Marine, deep rear 64 liters MIN 17 U.S.gal
Power Generator 102 liters MIN 27 U.S.gal
Oil Pump End Clearance 0.1016 mm MIN 0.004 in
0.2540 mm MAX 0.010 in

22.324 mm MAX 0.8785 in
Lubricating Oil System - Specifications QSK
Pressure Regulator Spring Free Length 95 mm Nominal 3.75 in

Spring Force @ 63.88 mm [2.5 in] Working
Height 322 N MIN 72 lb
344 N MAX 77 lb
Shaft O.D. 22.212 mm MIN 0.8745 in

22.225 mm MAX 0.8750 in
Gear I.D. 22.169 mm MIN 0.8728 in

22.195 mm MAX 0.8738 in
22.225 mm MAX 0.8750 in
ProCarManuals.com
Gear Location on Shaft

Idler 26.162 mm MIN 1.03 in
26.67 mm MAX 1.051 in
Drive 26.162 mm MIN 1.03 in
26.416 mm MAX 1.040 in

Free Length 88.98 mm MAX 3.500 in
29 N•m MAX 21.3 ft-lb
QSK Lubricating Oil System - Torque Values
Lubricating Oil System - Torque Values

Lube Oil Cooler Element Pressure Test 415 kPa 60 psi

Bypass Plunger and Spring 54 N•m 40 ft-lb
Piston Cooling Nozzle Plunger and Spring 54 N•m 40 ft-lb

ProCarManuals.com
Oil Filter Head Pipe Plugs

1-5/16 61 N•m 45 ft-lb
9/16 14 N•m 10 ft-lb
Lube Oil Filter Head Adapter 23 N•m 17 ft-lb

9/16 Plug 14 N•m 10 ft-lb
1-3/16 Plug 54 N•m 40 ft-lb
1-7/8 Plug 95 N•m 70 ft-lb

Lube Oil Pump Rear Cover 45 N•m 35 ft-lb
Lubricating Oil System - Torque Values QSK

9/16 Plug 14 N•m 10 ft-lb
1 3/16 Plug 54 N•m 40 ft-lb
1 7/8 Plug 95 N•m 70 ft-lb
ProCarManuals.com
QSK Cooling System - Specifications
Cooling System - Specifications

Bearing End Clearance 0.08 mm MIN 0.003 in
0.25 mm MAX 0.010 in

Bearing End Clearance 0.025 mm MIN 0.001 in
0.102 mm MAX 0.004 in

Impeller Vane-To-Body Clearance 0.58 mm MIN 0.023 in
0.86 mm MAX 0.034 in
ProCarManuals.com
Impeller to Shaft Press Fit 0.03 mm MIN 0.001 in

0.07 mm MAX 0.003 in
Housing Bore I.D.

(13) Water Seal 36.45 mm MIN 1.435 in
36.47 mm MAX 1.436 in
(14) Oil Seal 44.43 mm MIN 1.749 in
44.48 mm MAX 1.751 in
(15) Rear Bearing 51.996 mm MIN 2.0471 in
52.215 mm MAX 2.0557 in
(16) Front Bearing 71.996 mm MIN 2.8345 in
72.215 mm MAX 2.8431 in
Seat Dimension 10.52 mm MIN 0.414 in

10.57 mm MAX 0.416 in

Air Pressure 415 kPa MAX 60 psi
Cooling System - Specifications QSK

Bearing to Shaft Differences
Clearance 0.003 mm MAX 0.0001 in
Interference 0.018 mm MAX 0.0007 in
ProCarManuals.com
QSK Cooling System - Torque Values
Cooling System - Torque Values

Thermostat Housing Capscrews 45 N•m 35 ft-lb
Thermostat Housing Capscrews 45 N•m 35 ft-lb

ProCarManuals.com

Fan Hub Grease Fittings 15 N•m 135 in-lb
Fan Hub Lock Nut 610 N•m 450 ft-lb
Fan Hub Pilot Capscrews 20 N•m 15 ft-lb

Cooling System - Torque Values QSK

Water Pump Shut Off Valve Capscrew 20 N•m 15 ft-lb
45 N•m 35 ft-lb
Water Pump Inlet Connection Capscrews 40 N•m 30 ft-lb

ProCarManuals.com

Torque Converter Cooler Housing
Capscrews 130 N•m 95 ft-lb
Torque Converter Cooler Cover 45 N•m 35 ft-lb
Torque Converter Cooler Heater Plug 75 N•m 55 ft-lb

QSK Drive Units - Specifications
Drive Units - Specifications

Fuel Pump/Compressor Drive End
Clearance 0.05 mm MIN 0.002 in
0.30 mm MAX 0.012 in

33.50 mm MAX 1.319 in
Thrust Bearing Thickness 2.36 mm MIN 0.093 in

2.41 mm MAX 0.095 in
ProCarManuals.com
Shaft O.D.
(5) 34.963 mm MIN 1.3765 in
34.976 mm MAX 1.3770 in
(6) 34.662 mm MIN 1.5616 in
39.674 mm MAX 1.5620 in
(7) 33.30 mm MIN 1.300 in
33.33 mm MAX 1.312 in
(8) 25.476 mm MIN 1.0030 in
25.489 mm MAX 1.0035 in
Pully I.D. 34.912 mm MIN 1.3745 in

34.938 mm MAX 1.3755 in
Lovejoy Coupling I.D. 25.425 mm MIN 1.0010 in

25.438 mm MAX 1.0015 in
Spline Coupling I.D. 25.400 mm MIN 1.0000 in
25.425 mm MAX 1.0010 in
End Clearance 0.05 mm MIN 0.002 in

0.30 mm MAX 0.012 in
Drive Units - Specifications QSK

Gear I.D. 39.73 mm MIN 1.564 in
39.75 mm MAX 1.565 in

39.802 mm MAX 1.5670 in
Fuel Pump Drive Gear to Shaft 0.05 mm MAX 0.002 in

ProCarManuals.com

0.48 mm MAX 0.019 in

0.48 mm MAX 0.019 in

Idler Gear End Clearance 0.10 mm MIN 0.004 in
0.51 mm MAX 0.020 in
Lower Housing-To-Cylinder Block Gear

0.51 mm MAX 0.015 in
Idler Gear Backlash 0.05 mm MIN 0.002 in

0.51 mm MAX 0.020 in

Upper to Lower Housing Gasket
Thickness-Nominal (New*)
Part No. 205723 0.38 mm Nominal 0.015 in
Center Drive Shaft Bushing I.D. 47.536 mm MIN 1.8715 in

47.549 mm MAX 1.8720 in
ProCarManuals.com
Upper Housing Thrust Bearing Thickness 2.27 mm MIN 0.085 in

2.31 mm MAX 0.091 in
Hydraulic Drive Housing Bushing I.D. 47.60 mm MIN 1.874 in

47.68 mm MAX 1.877 in
Hydraulic Pump Support Bushing I.D. 47.60 mm MIN 1.874 in

47.68 mm MAX 1.877 in
Center Drive End Clearance 0.10 mm MIN 0.004 in

0.51 mm MAX 0.020 in
Drive Units - Specifications QSK
Center Drive Gear to Outer Drive Gear

0.51 mm MAX 0.020 in
Center Drive Gear to Outer Drive Gear

0.51 mm MAX 0.020 in
Water Pump Drive (009-029)

Water Pump Drive End Clearance 0.23 mm MIN 0.009 in
0.33 mm MAX 0.013 in
ProCarManuals.com
Water Pump Drive End Clearance 0.23 mm MIN 0.009 in

0.33 mm MAX 0.013 in

Drive Shaft Bushing Diameters 47.536 mm MIN 1.8715 in
47.549 mm MAX 1.8720 in
Thrust Bearing Thickness 2.27 mm MIN 0.085 in

2.31 mm MAX 0.091 in
Hydraulic Pump Support Bushing I.D. 47.60 mm MIN 1.874 in

47.68 mm MAX 1.877 in
Hydraulic Drive Gear End Clearance 0.10 mm MIN 0.004 in

0.51 mm MAX 0.020 in

Hydraulic Pump Support Bore I.D. 53.86 mm MIN 2.121 in
53.92 mm MAX 2.123 in
Hydraulic Pump Support Bushing Bore

I.D. 47.60 mm MIN 1.874 in
47.68 mm MAX 1.877 in
ProCarManuals.com
Drive Units - Torque Values QSK
Drive Units - Torque Values

Drain Plugs 100 N•m 75 ft-lb
11 N•m 8 in-lb
20 N•m 15 ft-lb
ProCarManuals.com
Rear Gear Drive Capscrews Step 1 100 N•m 75 ft-lb

2 205 N•m 150 ft-lb
Rear Gear Drive Capscrews

3/8-16 inch 45 N•m 35 ft-lb
7/16-14 inch 65 N•m 50 ft-lb
Mounting Capscrews

20 N•m 15 ft-lb
QSK Drive Units - Torque Values
Adapter 95 N•m 70 ft-lb

Cover Plate SAE C/SAE B Drive 95 N•m 70 ft-lb
Cover Plate SAE A Drive 40 N•m 35 ft-lb
40 N•m 30 ft-lb
70 N•m 50 ft-lb
ProCarManuals.com
70 N•m 50 ft-lb

Adapter 95 N•m 70 ft-lb
Cover Plate SAE

C/SAE B
drive 95 N•m 70 ft-lb
SAE A drive 40 N•m 35 ft-lb
Air Intake System - Specifications QSK
Air Intake System - Specifications

Air Pressure 415 kPa MAX 60 psi

Turbocharger End Clearance 0.05 mm MIN 0.002 in
0.13 mm MAX 0.005 in
Holset HX82 Turbocharger

Compressor Impeller 0.15 mm MIN 0.006 in
0.45 mm MAX 0.018 in
Turbine Wheel 0.20 mm MIN 0.008 in
0.55 mm MAX 0.210 in
ProCarManuals.com
QSK Air Intake System - Torque Values
Air Intake System - Torque Values

35 N•m 25 ft-lb


35 N•m 25 ft-lb
ProCarManuals.com
Exhaust System - Specifications QSK
Exhaust System - Specifications

Exhaust Manifold Capscrew Holes 191.5 mm MIN 7.54 in
193.5 mm MAX 7.62 in
ProCarManuals.com
QSK Electrical Equipment - Specifications
Electrical Equipment - Specifications

Drive Belt, Alternator (013-005)
Alternator Belt Tension 670 N 150 lbf
ProCarManuals.com
Engine Testing - Specifications QSK
Engine Testing - Specifications

Engine Testing (Chassis Dynamometer) (014-005)
Maximum Coolant Pressure with Closed
Thermostat and No Pressure Cap 241 kPa 35 psi
Hose Temperature (Minimum) 260 °C 500 °F
Engine Testing (Engine Dynamometer) (014-005)

Lubricating Oil Pressure 138 kPa MIN 20 psi
207 kPa Nominal 30 psi
ProCarManuals.com
QSK Drive Belt Tension
Drive Belt Tension

SAE Belt Size Belt Tension Gauge Part No. Belt Tension New Belt Tension Range Used*
Click-type Burroughs N lbf N lbf
0.380 in 3822524 620 140 270 to 490 60 to 110
0.440 in 3822524 620 140 270 to 490 60 to 110
1/2 in 3822524 ST-1138 620 140 270 to 490 60 to 110
11/16 in 3822524 ST-1138 620 140 270 to 490 60 to 110
3/4 in 3822524 ST-1138 620 140 270 to 490 60 to 110
7/8 in 3822524 ST-1138 620 140 270 to 490 60 to 110
4 rib 3822524 ST-1138 620 140 270 to 490 60 to 110
5 rib 3822524 ST-1138 670 150 270 to 530 60 to 120
6 rib 3822525 ST-1293 710 160 290 to 580 65 to 130
8 rib 3822525 ST-1293 890 200 360 to 710 80 to 160
10 rib 3822525 3823138 1110 250 440 to 890 100 to 200
12 rib 3822525 3823138 1330 300 530 to 1070 120 to 240
12 rib K section 3822525 3823138 1330 300 890 to 1070 200 to 240
Note: This chart does not apply to automatic belt tensioners.
ProCarManuals.com
* A belt is considered used if it has been in service for ten minutes or longer.
* If used belt tension is less than the minimum value, tighten the belt to the maximum used belt value.
g-01 (belt)
Capscrew Markings and Torque Values QSK
Capscrew Markings and Torque Values

CAUTION
When replacing capscrews, always use a capscrew of the same measurement and strength as the capscrew
being replaced. Using the wrong capscrews can result in engine damage.
Metric capscrews and nuts are identified by the grade number stamped on the head of the capscrew or on the surface
of the nuts. U.S. Customary capscrews are identified by radial lines stamped on the head of the capscrew.
The following examples indicate how capscrews are identified:
NOTES:
1. Always use the torque values listed in the following tables when specific torque values are not available.
ProCarManuals.com
2. Do not use the torque values in place of those specified in other sections of this manual.
3. The torque values in the table are based on the use of lubricated threads.
4. When the ft-lb value is less than 10, convert the ft-lb value to in-lb to obtain a better torque with an in-lb torque
wrench. Example: 6 ft-lb equals 72 in-lb.
g-01 (nom)
QSK Capscrew Markings and Torque Values
Capscrew Markings and Torque Values - Metric
Body
Size Torque Torque Torque
Diam. Cast Iron Aluminum Cast Iron Aluminum Cast Iron Aluminum
mm N•m ft-lb N•m ft-lb N•m ft-lb N•m ft-lb N•m ft-lb N•m ft-lb
6 9 5 7 4 12 9 7 4 14 9 7 4
7 14 9 11 7 18 14 11 7 23 18 11 7
8 25 18 18 14 33 25 18 14 40 29 18 14
10 45 33 30 25 60 45 30 25 70 50 30 25
12 80 60 55 40 105 75 55 40 125 95 55 40
14 125 90 90 65 165 122 90 65 195 145 90 65
16 180 130 140 100 240 175 140 100 290 210 140 100
ProCarManuals.com
18 230 170 180 135 320 240 180 135 400 290 180 135
g-01 (cap-m)
Capscrew Markings and Torque Values QSK
Capscrew Markings and Torque Values - U.S. Customary
Capscrew Body Size Cast Iron Aluminum Cast Iron Aluminum

N•m ft-lb N•m ft-lb N•m ft-lb N•m ft-lb
1/4 - 20 9 7 8 6 15 11 8 6
- 28 12 9 9 7 18 13 9 7
5/16 - 18 20 15 16 12 30 22 16 12
- 24 23 17 19 14 33 24 19 14
3/8 - 16 40 30 25 20 55 40 25 20
- 24 40 30 35 25 60 45 35 25
7/16 - 14 60 45 45 35 90 65 45 35
- 20 65 50 55 40 95 70 55 40
1/2 - 13 95 70 75 55 130 95 75 55
- 20 100 75 80 60 150 110 80 60
9/16 - 12 135 100 110 80 190 140 110 80
- 18 150 110 115 85 210 155 115 85
5/8 - 11 180 135 150 110 255 190 150 110
- 18 210 155 160 120 290 215 160 120
3/4 - 10 325 240 255 190 460 340 255 190
ProCarManuals.com
- 16 365 270 285 210 515 380 285 210

7/8 - 9 490 360 380 280 745 550 380 280
- 14 530 390 420 310 825 610 420 310
1 - 8 720 530 570 420 1100 820 570 420
- 14 800 590 650 480 1200 890 650 480
g-02 (cap-i)
QSK Fraction, Decimal, Millimeter Conversions
Fraction, Decimal, Millimeter Conversions

Fraction inch mm Fraction inch mm
1/64 0.0156 0.397 33/64 0.5156 13.097
1/32 0.0313 0.794 17/32 0.5313 13.494
3/64 0.0469 1.191 35/64 0.5469 13.891
1/16 0.0625 1.588 9/16 0.5625 14.288
5/64 0.0781 1.984 37/64 0.5781 14.684
3/32 0.0938 2.381 19/32 0.5938 15.081
7/64 0.1094 2.778 39/64 0.6094 15.478
1/8 0.1250 3.175 5/8 0.6250 15.875
9/64 0.1406 3.572 41/64 0.6406 16.272
5/32 0.1563 3.969 21/32 0.6563 16.669
11/64 0.1719 4.366 43/64 0.6719 17.066
3/16 0.1875 4.763 11/16 0.6875 17.463
13/64 0.2031 5.159 45/64 0.7031 17.859
ProCarManuals.com
7/32 0.2188 5.556 23/32 0.7188 18.256

15/64 0.2344 5.953 47/64 0.7344 18.653
1/4 0.2500 6.350 3/4 0.7500 19.050
17/64 0.2656 6.747 49/64 0.7656 19.447
9/32 0.2813 7.144 25/32 0.7813 19.844
19/64 0.2969 7.541 51/64 0.7969 20.241
5/16 0.3125 7.938 13/16 0.8125 20.638
21/64 0.3281 8.334 53/64 0.8281 21.034
11/32 0.3438 8.731 27/32 0.8438 21.431
23/64 0.3594 9.128 55/64 0.8594 21.828
3/8 0.3750 9.525 7/8 0.8750 22.225
25/64 0.3906 9.922 57/64 0.8906 22.622
13/32 0.4063 10.319 29/32 0.9063 23.019
27/64 0.4219 10.716 59/64 0.9219 23.416
7/16 0.4375 11.113 15/16 0.9375 23.813
29/64 0.4531 11.509 61/64 0.9531 24.209
15/32 0.4688 11.906 31/32 0.9688 24.606
31/64 0.4844 12.303 63/64 0.9844 25.003
1/2 0.5000 12.700 1 1.0000 25.400
Conversion Factor: 1 inch = 25.4 mm
g-01 (convert)
Newton-Meter to Foot-Pound Conversion Chart QSK
Newton-Meter to Foot-Pound Conversion Chart

N•m ft-lb N•m ft-lb N•m ft-lb
1 8.850756 in-lb 55 41 155 114
5 44 in-lb 60 44 160 118
6 53 in-lb 65 48 165 122
7 62 in-lb 70 52 170 125
8 71 in-lb 75 55 175 129
9 80 in-lb 80 59 180 133
10 89 in-lb 85 63 185 136
1 0.737562 ft-lb 90 66 190 140
12 9 95 70 195 144
14 10 100 74 200 148
15 11 105 77 205 151
16 12 110 81 210 155
18 13 115 85 215 159
20 15 120 89 220 162
25 18 125 92 225 165
ProCarManuals.com
30 22 130 96 230 170

35 26 135 100 235 173
40 30 140 103 240 177
45 33 145 107 245 180
50 37 150 111 250 184
NOTE: To convert from Newton-Meters to Kilogram-Meters divide Newton-Meters by 9.803.
g-01 (newton)
QSK Pipe Plug Torque Values
Pipe Plug Torque Values

Size Torque Torque
In Cast Iron or
Thread Actual Thread O.D. In Aluminum Components Steel Components
in in N•m ft-lb N•m ft-lb
1/16 0.32 5 45 in-lb 15 10
1/8 0.41 15 10 20 15
1/4 0.54 20 15 25 20
3/8 0.68 25 20 35 25
1/2 0.85 35 25 55 40
3/4 1.05 45 35 75 55
1 1.32 60 45 95 70
1-1/4 1.66 75 55 115 85
1-1/2 1.90 85 65 135 100
ProCarManuals.com
g-01 (plug)
Tap-Drill Chart - U.S. Customary and Metric QSK
Tap-Drill Chart - U.S. Customary and Metric

ProCarManuals.com
g-01 (tap)
QSK Weights and Measures - Conversion Factors
Weights and Measures - Conversion Factors

Quantity U.S. Customary Metric From U.S. From Metric
Customary To U.S.
To Metric Customary
Multiply By Multiply By
Unit Name Abbr. Unit Name Abbr.
Area sq. inch in2 sq. millimeters mm2 645.16 0.001550
sq. centimeters cm2 6.452 0.155
2 2
sq. foot ft sq. meter m 0.0929 10.764
Fuel pounds per lb/hp-hr grams per kilowatt g/kW-hr 608.277 0.001645
Consumption horsepower hour hour
Fuel miles per gallon mpg kilometers per liter km/l 0.4251 2.352
Performance
gallons per mile gpm liters per kilometer l/km 2.352 0.4251
Force pounds force lbf Newton N 4.4482 0.224809
Length inch in millimeters mm 25.40 0.039370
foot ft millimeters mm 304.801 0.00328
Power horsepower hp kilowatt kW 0.746 1.341
ProCarManuals.com
Pressure pounds force per psi kilopascal kPa 6.8948 0.145037

sq. inch
inches of mercury in Hg kilopascal kPa 3.3769 0.29613
inches of water in H2O kilopascal kPa 0.2488 4.019299
inches of mercury in Hg millimeters of mm Hg 25.40 0.039370
mercury
inches of water in H2O millimeters of water mm H2O 25.40 0.039370
bars bars kilopascals kPa 100.001 0.00999
bars bars millimeters of mm Hg 750.06 0.001333
mercury
Temperature fahrenheit °F centigrade °C (°F-32) ÷1.8 (1.8 x °C) +32
Torque pound force per foot ft-lb Newton-meter N•m 1.35582 0.737562
pound force per inch in-lb Newton-meter N•m 0.113 8.850756
Velocity miles/hour mph kilometers/hour kph 1.6093 0.6214
Volume: gallon (U.S.) gal. liter l 3.7853 0.264179
liquid
displacement gallon (Imp*) gal. liter l 4.546 0.219976
3
cubic inch in liter l 0.01639 61.02545
cubic inch in3 cubic centimeter cm3 16.387 0.06102
Weight (mass) pounds (avoir.) lb kilograms kg 0.4536 2.204623
Work British Thermal Unit BTU joules J 1054.5 0.000948
British Thermal Unit BTU kilowatt-hour kW-hr 0.000293 3414
horsepower hours hp-hr kilowatt-hour kW-hr 0.746 1.341
g-01 (weight)
Weights and Measures - Conversion Factors QSK
NOTES
ProCarManuals.com
Index
Page 1
About the Manual...................................................................... i-1 Complete Engine - Torque Values ........................................... V-3
Accessory Drive Pulley ............................................................ 9-3 Engine Assembly .................................................................... V-3
Inspect for Reuse ................................................................... 9-3 Engine Disassembly ............................................................... V-3
Install ..................................................................................... 9-3 Component Manufacturers’ Addresses .................................. M-1
Remove ................................................................................. 9-3 Air Compressors .................................................................... M-1
Additional Service Literature ................................................... L-1 Air Cylinders .......................................................................... M-1
Aftercooler Assembly............................................................. 10-3 Air Heaters............................................................................. M-1
Assemble ............................................................................. 10-5 Air Starting Motors ................................................................. M-1
Clean ................................................................................... 10-4 Alternators ............................................................................. M-1
Disassemble ......................................................................... 10-4 Auxiliary Brakes ..................................................................... M-1
Exploded View ...................................................................... 10-3 Belts ...................................................................................... M-1
Inspect for Reuse ................................................................. 10-4 Catalytic Convertors ............................................................... M-1
Aftercooler Coolant Tube ....................................................... 10-6 Clutches ................................................................................ M-1
Clean ................................................................................... 10-6 Coolant Heaters ..................................................................... M-2
Inspect for Reuse ................................................................. 10-6 Coolant Level Switches .......................................................... M-1
Air Crossover.......................................................................... 10-7 Drive Plates ........................................................................... M-2
Clean ................................................................................... 10-7 Electric Starting Motors .......................................................... M-2
Inspect for Reuse ................................................................. 10-7 Electronic Switches ................................................................ M-2
Air Intake System - General Information ............................... 10-1 Engine Protection Controls..................................................... M-2
Preparatory .......................................................................... 10-1 Fan Clutches.......................................................................... M-2
Air Intake System - Specifications ........................................ V-42 Fans....................................................................................... M-2
Aftercooler Assembly ............................................................ V-42 Fault Lamps ........................................................................... M-2
Turbocharger, Water-Cooled .................................................. V-42 Filters..................................................................................... M-2
Air Intake System - Torque Values ........................................ V-43 Flexplates .............................................................................. M-2
Aftercooler Assembly ............................................................ V-43 Fuel Coolers .......................................................................... M-2
Turbocharger Heat Shield ..................................................... V-43 Fuel Warmers ........................................................................ M-2
Alternator Adjusting Link....................................................... 13-4 Gauges .................................................................................. M-2
Clean ................................................................................... 13-4 Governors .............................................................................. M-3
Inspect for Reuse ................................................................. 13-4 Heat Sleeves.......................................................................... M-3
Alternator Bracket .................................................................. 13-2 Hydraulic and Power Steering Pumps .................................... M-3
Clean ................................................................................... 13-2 In-Line Connectors ................................................................. M-3
ProCarManuals.com
Inspect for Reuse ................................................................. 13-2 Oil Heaters............................................................................. M-3

Bearings, Connecting Rod....................................................... 1-5 Prelubrication Systems........................................................... M-3
Clean ..................................................................................... 1-5 Radiators ............................................................................... M-3
Inspect for Reuse ................................................................... 1-5 Throttle Assemblies................................................................ M-3
Bearings, Main ......................................................................... 1-5 Torque Converters .................................................................. M-3
Clean ..................................................................................... 1-5 Compressed Air System - General Information..................... 12-1
Inspect for Reuse ................................................................... 1-6 General Information ............................................................. 12-1
Measure ................................................................................ 1-6 Connecting Rod ..................................................................... 1-18
Bearings, Thrust ...................................................................... 1-6 Clean ................................................................................... 1-18
Assemble ................................................................................ 1-7 Inspect for Reuse ................................................................. 1-18
Inspect for Reuse ................................................................... 1-6 Magnetic Crack Inspect ........................................................ 1-24
Cam Follower Assembly........................................................... 4-2 Coolant Thermostat ................................................................. 8-4
Assemble ............................................................................... 4-5 Install ..................................................................................... 8-6
Clean ..................................................................................... 4-3 Conventional Aftercooling................................................... 8-6
Disassemble .......................................................................... 4-3 Low Temperature Aftercooling ............................................ 8-7
Exploded View ........................................................................ 4-2 Remove ................................................................................. 8-4
Inspect for Reuse ................................................................... 4-4 Test ........................................................................................ 8-8
Cam Follower Cover ................................................................. 4-6 Engine Thermostats ........................................................... 8-8
Clean ..................................................................................... 4-6 Low Temperature Aftercooling Thermostat .......................... 8-9
General Information ............................................................... 4-6 Coolant Thermostat Housing Support................................... 8-10
Inspect for Reuse ................................................................... 4-6 General Information .............................................................. 8-10
Cam Followers/Tappets - General Information ........................ 4-1 LTA Cooling System.......................................................... 8-10
Cam Followers/Tappets - Specifications ............................... V-24 Thermostat ....................................................................... 8-10
Cam Follower Assembly........................................................ V-24 Thermostat Seal ............................................................... 8-10
Camshaft .................................................................................. 1-7 Thermostat Support.......................................................... 8-10
Clean ..................................................................................... 1-7 Cooling System - General Information .................................... 8-1
Inspect for Reuse ................................................................... 1-7 General Information ............................................................... 8-1
Magnetic Crack Inspect ......................................................... 1-8 Cooling System - Specifications ........................................... V-31
Camshaft Bushings................................................................ 1-15 Fan Drive Idler Pulley Assembly ............................................ V-31
Inspect for Reuse ................................................................. 1-16 Fan Hub, Belt Driven............................................................. V-31
Install ................................................................................... 1-16 Torque Converter Cooler ....................................................... V-31
Remove ............................................................................... 1-15 Water Pump.......................................................................... V-31
Camshaft Gear (Camshaft Removed)..................................... 1-10 Water Pump Bearings ........................................................... V-32
Inspect for Reuse ................................................................. 1-11 Cooling System - Torque Values ........................................... V-33
Install ................................................................................... 1-14 Coolant Thermostat .............................................................. V-33
Magnetic Crack Inspect ........................................................ 1-12 Fan Hub, Belt Driven ............................................................ V-33
Remove ................................................................................ 1-10 Torque Converter Cooler ....................................................... V-34
Capscrew Markings and Torque Values................................. V-48 Water Pump.......................................................................... V-34
Capscrew Markings and Torque Values - Metric ................... V-49 Crankcase Breather (External)................................................. 3-4
Capscrew Markings and Torque Values - U.S. Customary .... V-50 Clean ..................................................................................... 3-5
Charge Air Cooler (CAC) ........................................................ 10-8 Install ..................................................................................... 3-6
Clean ................................................................................... 10-8 Remove ................................................................................. 3-4
Inspect for Reuse ................................................................. 10-8 Crankshaft .............................................................................. 1-25
Leak Test .............................................................................. 10-9 Bend and Twist Inspect ........................................................ 1-29
Complete Engine - Specifications........................................... V-1 Clean ................................................................................... 1-25
Engine Assembly .................................................................... V-1 Inspect for Reuse ................................................................. 1-26
Index
Page 2
Magnetic Crack Inspect ........................................................ 1-27 Drive Belt, Alternator ............................................................. 13-2
Crankshaft Gear, Front (Crankshaft Installed) ....................... 1-34 Adjust .................................................................................. 13-2
Inspect for Reuse ................................................................. 1-35 Drive Belt Tension.................................................................. V-47
Install ................................................................................... 1-35 Drive Units - General Information............................................ 9-1
Remove ............................................................................... 1-34 General Information ............................................................... 9-1
Crankshaft Gear, Rear (Crankshaft Installed) ........................ 1-36 Drive Units - Specifications ................................................... V-35
Install .................................................................................... 1-36 Fuel Pump Drive................................................................... V-35
Crankshaft Pulley ................................................................... 1-36 Fuel Pump Drive Gear and Shaft .......................................... V-36
Clean ................................................................................... 1-36 Hydraulic Pump Drive ........................................................... V-36
Inspect for Reuse ................................................................. 1-37 Hydraulic Pump Support Bushing ......................................... V-39
Crosshead ................................................................................ 2-4 Outer Hydraulic Pump Support Drive .................................... V-38
Clean ..................................................................................... 2-4 Rear Gear Drive (Lower Assembly) ....................................... V-36
Inspect for Reuse ................................................................... 2-4 Rear Gear Drive (Upper Assembly) ....................................... V-37
Cylinder Block........................................................................ 1-38 Water Pump Drive................................................................. V-38
Clean ................................................................................... 1-39 Drive Units - Torque Values ................................................... V-40
Inspect for Reuse ................................................................. 1-41 Outer Hydraulic Pump Support Drive .................................... V-41
Magnetic Crack Inspect ........................................................ 1-45 Rear Gear Drive (Lower Assembly) ....................................... V-40
Worksheet ............................................................................ 1-38 Rear Gear Drive (Upper Assembly) ....................................... V-40
Cylinder Block - General Information ...................................... 1-1 Dynamometer Worksheet ..................................................... 14-10
General Information ............................................................... 1-1 Worksheet .......................................................................... 14-10
Cylinder Block - Specifications ............................................. V-13 Electrical Equipment - General Information .......................... 13-1
Bearings, Main ..................................................................... V-13 General Information ............................................................. 13-1
Camshaft .............................................................................. V-13 Electrical Equipment - Specifications ................................... V-45
Camshaft Bushings............................................................... V-13 Drive Belt, Alternator............................................................. V-45
Camshaft Gear (Camshaft Removed).................................... V-13 Electronic Engine Controls - General Information ................ 19-1
Connecting Rod.................................................................... V-14 General Information ............................................................. 19-1
Crankshaft ............................................................................ V-15 Connector Pins — Checking ............................................ 19-3
Crankshaft Gear, Front (Crankshaft Installed) ........................ V-15 Continuity Check.............................................................. 19-7
Crankshaft Pulley.................................................................. V-15 How To Find The Internal Resistance of The Meter .......... 19-2
Cylinder Block ...................................................................... V-15 How To Measure Current.................................................. 19-1
Cylinder Block and Liner Seats............................................. V-15 How To Measure Resistance ............................................ 19-2
ProCarManuals.com
Cylinder Block Counterbore .................................................. V-18 How To Measure Voltage .................................................. 19-2
Cylinder Liner ....................................................................... V-16 How To Test For Continuity ............................................... 19-2
Gear Cover Accessory Drive Bushing ................................... V-18 How To Use A Digital Volt/Ohm Meter .............................. 19-1
Gear Cover, Front ................................................................. V-17 Polarity Check.................................................................. 19-6
Gear Cover Spacer Plate ...................................................... V-17 Resistance Check — Coil................................................. 19-8
Idler Gear, Camshaft............................................................. V-17 Short Circuit From Pin To Pin — Check ........................... 19-5
Measure the Connecting Rod Bend (Bore Alignment) ........... V-14 Short Circuit To Ground — Check .................................... 19-4
Measure the Connecting Rod Twist....................................... V-15 Use of Special Test Leads ................................................ 19-1
Piston ................................................................................... V-17 Voltage Checking ............................................................. 19-5
Cylinder Block - Torque Values ............................................. V-19 Engine Assembly ................................................................... 0-58
Connecting Rod.................................................................... V-19 Assemble ............................................................................. 0-58
Crankshaft Pulley.................................................................. V-19 Engine Diagrams ..................................................................... E-6
Cylinder Block ...................................................................... V-19 Engine Views ......................................................................... E-6
Cylinder Block Counterbore .................................................. V-19 Engine Disassembly................................................................. 0-8
Cylinder Block and Liner Seats ............................................. 1-47 Disassemble .......................................................................... 0-9
General Information ............................................................. 1-47 General Information ............................................................... 0-8
Inspect for Reuse ................................................................. 1-47 Assembly ........................................................................... 0-8
Leak Test............................................................................... 1-51 Disassembly ...................................................................... 0-8
Measure ............................................................................... 1-49 Engine Identification ............................................................... E-1
Cylinder Block Counterbore .................................................. 1-65 Cummins Engine Nomenclature ............................................ E-1
Machine ............................................................................... 1-65 ECM Dataplate ...................................................................... E-1
Cylinder Head .......................................................................... 2-5 Engine Dataplate ................................................................... E-1
Assemble ............................................................................. 2-14 Engine Run-in (Chassis Dynamometer)............................... 14-23
Clean ..................................................................................... 2-6 General Information ............................................................ 14-23
Disassemble ........................................................................ 2-13 Engine Throttle Control .................................................. 14-24
Exploded View ........................................................................ 2-5 Run-In Instructions ............................................................. 14-26
Inspect for Reuse ................................................................... 2-6 Engine Run-in (Engine Dynamometer) ................................ 14-42
Pressure Test ......................................................................... 2-8 General Information ............................................................ 14-42
Vacuum Test ......................................................................... 2-10 Run-In Instructions ............................................................. 14-44
Cylinder Head - General Information....................................... 2-1 Engine Run-in (Without Dynamometer)............................... 14-28
General Information ............................................................... 2-1 Preparatory ........................................................................ 14-28
Cylinder Head - Specifications.............................................. V-20 General Engine Test Procedures .................................... 14-28
Cylinder Head....................................................................... V-20 Run-In Instructions ............................................................. 14-30
Cylinder Head Injector Bore.................................................. V-20 Generator Set................................................................. 14-30
Valve, Cylinder Head............................................................. V-21 Off-Highway ................................................................... 14-30
Valve Guide, Cylinder Head .................................................. V-20 Engine Support Bracket, Front .............................................. 16-4
Valve Seat Bore .................................................................... V-21 Clean ................................................................................... 16-4
Valve Seat Insert, Cylinder Head........................................... V-21 Inspect for Reuse ................................................................. 16-4
Cylinder Head Injector Bore .................................................. 2-15 Engine Testing - General Information.................................... 14-1
Adjust .................................................................................. 2-17 Fuel Flow Measurement on Engine or Chassis Dynamometer . 14-2
Inspect for Reuse ................................................................. 2-15 Installation ....................................................................... 14-2
Cylinder Liner......................................................................... 1-51 Operation ......................................................................... 14-3
Clean ................................................................................... 1-51 General Information ............................................................. 14-1
Inspect for Reuse ................................................................. 1-52 Engine Testing - Specifications............................................. V-46
Cylinder Liner Protrusion ...................................................... 1-79 Engine Testing (Chassis Dynamometer) ................................ V-46
Adjust .................................................................................. 1-79 Engine Testing (Engine Dynamometer) ................................. V-46
Index
Page 3
Engine Testing (Chassis Dynamometer) .............................. 14-11 Clean ..................................................................................... 6-4

Setup ................................................................................. 14-11 Inspect for Reuse ................................................................... 6-5
Test .................................................................................... 14-14 Fuel Control Supply Line.................................................... 6-5
Engine Testing (Engine Dynamometer) ............................... 14-31 Fuel Inlet Line .................................................................... 6-6
Install ................................................................................. 14-31 Fuel Rail Supply Line......................................................... 6-5
Test .................................................................................... 14-34 Fuel Tank-To-Fuel Filter ...................................................... 6-5
Engine Testing (In Chassis) ................................................. 14-47 Fuel Timing and Supply Line ............................................. 6-5
Stall Speed Check ............................................................. 14-47 Fuel System - General Information.......................................... 5-1
Time Speed Check ............................................................ 14-50 General Information ............................................................... 5-1
Engine Wiring Harness .......................................................... 19-8 Fuel System - Torque Values ................................................. V-25
Inspect for Reuse ................................................................. 19-8 Fuel Shutoff Valve (FSOV)..................................................... V-25
Exhaust Manifold, Dry ............................................................ 11-1 Gear Cover Accessory Drive Bushing ................................... 1-80
Assemble ............................................................................. 11-3 Install ................................................................................... 1-80
Clean ................................................................................... 11-1 Remove ............................................................................... 1-80
Marine Applications ........................................................... 11-2 Gear Cover, Front................................................................... 1-55
Disassemble ......................................................................... 11-2 Clean ................................................................................... 1-55
Inspect for Reuse ................................................................. 11-2 Inspect for Reuse ................................................................. 1-56
Marine Applications ........................................................... 11-3 Measure ............................................................................... 1-57
Exhaust Manifold Heat Shield ................................................ 11-3 Gear Cover Spacer Plate........................................................ 1-55
Clean ................................................................................... 11-3 Clean ................................................................................... 1-55
Exhaust System - General Information .................................. 11-1 General Cleaning Instructions .................................................. i-9
General Information .............................................................. 11-1 Glass or Plastic Bead Cleaning ............................................... i-9
Exhaust System - Specifications........................................... V-44 Solvent and Acid Cleaning ...................................................... i-9
Exhaust Manifold, Dry........................................................... V-44 Steam Cleaning ...................................................................... i-9
Fan, Cooling ........................................................................... 8-18 General Repair Instructions...................................................... i-8
General Information ............................................................. 8-18 Welding on a Vehicle with Electronic Components .................. i-8
Fan Drive Idler Arm Assembly ............................................... 8-11 General Safety Instructions ...................................................... i-7
Assemble ............................................................................. 8-12 Important Safety Notice ........................................................... i-7
Clean ................................................................................... 8-11 How to Use the Manual............................................................. i-1
Disassemble ......................................................................... 8-11 Hydraulic Pump Drive ............................................................ 9-14
ProCarManuals.com
Inspect for Reuse ................................................................. 8-11 Assemble ............................................................................. 9-16

Fan Drive Idler Pulley Assembly ............................................ 8-12 Clean ................................................................................... 9-15
Clean ................................................................................... 8-12 Disassemble ........................................................................ 9-15
Inspect for Reuse ................................................................. 8-13 Exploded View ...................................................................... 9-14
Fan Hub, Belt Driven .............................................................. 8-14 General Information ............................................................. 9-14
Assemble ............................................................................. 8-16 Inspect for Reuse ................................................................. 9-15
Clean ................................................................................... 8-15 Hydraulic Pump Drive Gear and Shaft................................... 9-17
General Information ............................................................. 8-14 Assemble ............................................................................. 9-18
Inspect for Reuse ................................................................. 8-15 Disassemble ........................................................................ 9-17
Flywheel ................................................................................. 16-4 Hydraulic Pump Support Bushing ......................................... 9-57
Clean ................................................................................... 16-4 Inspect for Reuse ................................................................. 9-58
Inspect for Reuse ................................................................. 16-5 Install ................................................................................... 9-58
Flywheel Housing................................................................... 16-6 Remove ............................................................................... 9-57
Clean ................................................................................... 16-6 Idler Gear, Camshaft .............................................................. 1-57
Inspect for Reuse ................................................................. 16-6 Clean ................................................................................... 1-57
Redowel ............................................................................... 16-7 Inspect for Reuse ................................................................. 1-57
Flywheel Ring Gear .............................................................. 16-10 Magnetic Crack Inspect ........................................................ 1-58
Assemble ............................................................................ 16-11 Idler Gear, Hydraulic Pump .................................................... 1-59
Disassemble ....................................................................... 16-10 Clean ................................................................................... 1-59
Fraction, Decimal, Millimeter Conversions ........................... V-51 Inspect for Reuse ................................................................. 1-60
Fuel Filter Head ....................................................................... 6-2 Idler Gear, Water Pump.......................................................... 1-60
Install ..................................................................................... 6-2 Clean ................................................................................... 1-60
Remove ................................................................................. 6-2 Inspect for Reuse ................................................................. 1-60
Fuel Manifold (Supply)............................................................. 6-3 Illustrations ............................................................................... i-6
Clean ..................................................................................... 6-3 Injector ..................................................................................... 6-6
Inspect for Reuse ................................................................... 6-4 Clean ..................................................................................... 6-6
Fuel Pump ................................................................................ 5-6 Inspect for Reuse ................................................................... 6-6
Calibrate ................................................................................ 5-7 Injectors and Fuel Lines - General Information ...................... 6-1
Clean ..................................................................................... 5-6 General Information ............................................................... 6-1
Inspect for Reuse ................................................................... 5-6 Injectors and Fuel Lines - Torque Values.............................. V-26
Fuel Pump Drive ...................................................................... 9-5 Fuel Manifold (Supply) .......................................................... V-26
Assemble ............................................................................. 9-10 Literature Order Form .............................................................. L-3
Clean ..................................................................................... 9-7 Lubricating Oil Cooler.............................................................. 7-3
Disassemble .......................................................................... 9-9 Clean ..................................................................................... 7-4
Exploded View ........................................................................ 9-6 Exploded View ........................................................................ 7-3
General Information ............................................................... 9-5 General Information ............................................................... 7-4
Inspect for Reuse ................................................................... 9-7 Inspect for Reuse ................................................................... 7-4
Fuel Pump Drive Gear and Shaft ........................................... 9-11 Lubricating Oil Filter Head....................................................... 7-5
Assemble ............................................................................. 9-12 Assemble ............................................................................. 7-10
Disassemble ......................................................................... 9-11 Clean ..................................................................................... 7-9
Fuel Shutoff Valve (FSOV) ....................................................... 5-9 Disassemble .......................................................................... 7-8
Clean ................................................................................... 5-10 Exploded View ........................................................................ 7-6
Inspect for Reuse ................................................................. 5-10 General Information ............................................................... 7-5
Install ................................................................................... 5-11 Inspect for Reuse ................................................................... 7-9
Remove ................................................................................. 5-9 Lubricating Oil Filter Head Adapter ....................................... 7-13
Fuel Supply Lines .................................................................... 6-4 Clean ................................................................................... 7-13
Index
Page 4
General Information ............................................................. 7-13 Assemble ............................................................................. 3-14

Inspect for Reuse ................................................................. 7-13 Clean ................................................................................... 3-12
Lubricating Oil Filter Head (Remote-Mounted) ...................... 7-11 Disassemble ........................................................................ 3-13
Assemble ............................................................................. 7-12 Exploded View ..................................................................... 3-10
Clean ................................................................................... 7-12 Inspect for Reuse ................................................................. 3-12
Disassemble ......................................................................... 7-11 Rocker Lever Bushings .......................................................... 3-14
Inspect for Reuse ................................................................. 7-12 Install ................................................................................... 3-14
Lubricating Oil Pan................................................................. 7-15 Remove ............................................................................... 3-14
General Information ............................................................. 7-15 Rocker Lever Cover ................................................................ 3-15
Oil Pan Capacity .............................................................. 7-15 Clean ................................................................................... 3-15
Lubricating Oil Pan Adapter................................................... 7-16 Inspect for Reuse ................................................................. 3-15
Clean ................................................................................... 7-16 Rocker Lever Housing............................................................ 3-15
Lubricating Oil Pump ............................................................. 7-17 Clean ................................................................................... 3-15
Assemble ............................................................................. 7-22 Inspect for Reuse ................................................................. 3-16
Clean ................................................................................... 7-19 Rocker Levers - General Information....................................... 3-1
Disassemble ........................................................................ 7-19 General Information ............................................................... 3-1
Exploded View ...................................................................... 7-18 Rocker Levers - Specifications .............................................. V-23
General Information ............................................................. 7-17 Rocker Lever ........................................................................ V-23
Inspect for Reuse ................................................................. 7-20 Rocker Lever Assembly......................................................... V-23
Lubricating Oil System - General Information......................... 7-1 Rocker Lever Bushings ......................................................... V-23
General Information ............................................................... 7-1 Service Literature Ordering Location ...................................... L-2
Lubricating Oil System - Specifications ................................ V-27 Service Tools .......................................................................... 10-2
Lubricating Oil Filter Head .................................................... V-27 Air Intake System .................................................................. 10-2
Lubricating Oil Filter Head (LF670) ....................................... V-27 Cooling System....................................................................... 8-3
Lubricating Oil Filter Head (Remote-Mounted)....................... V-27 Cylinder Block......................................................................... 1-2
Lubricating Oil Pan ............................................................... V-27 Cylinder Head ......................................................................... 2-2
Lubricating Oil Pump ............................................................ V-27 Drive Units .............................................................................. 9-2
Oil Transfer Connection ........................................................ V-28 Engine Disassembly and Assembly ......................................... 0-1
Lubricating Oil System - Torque Values ................................ V-29 Engine Testing ...................................................................... 14-8
Lubricating Oil Cooler ........................................................... V-29 Fuel System............................................................................ 5-4
ProCarManuals.com
Lubricating Oil Filter Head .................................................... V-29 Lubricating Oil System ............................................................ 7-2
Lubricating Oil Filter Head (Remote-Mounted)....................... V-29 Mounting Adaptations............................................................ 16-3
Lubricating Oil Pump ............................................................ V-29 Rocker Levers ......................................................................... 3-2
Oil Transfer Connection ........................................................ V-30 Specifications .......................................................................... E-2
Mounting Adaptations - General Information ........................ 16-1 Air Intake System .................................................................. E-2
General Information ............................................................. 16-1 Batteries (Specific Gravity)...................................................... E-5
Newton-Meter to Foot-Pound Conversion Chart ................... V-52 Cooling System ........................................................... E-4 , 14-7
OEM Interface Harness .......................................................... 19-9 Electrical System ................................................................... E-2
General Information ............................................................. 19-9 Engine Testing ..................................................................... 14-6
OEM Wiring Harness.............................................................. 19-9 Exhaust System ........................................................... E-4 , 14-7
General Information ............................................................. 19-9 Fuel System .......................................................................... E-2
Oil Transfer Connection ......................................................... 7-23 General Specifications ........................................................... E-2
Assemble ............................................................................. 7-24 Lubricating Oil System ................................................. E-3 , 14-7
Clean ................................................................................... 7-23 Starting Motor ........................................................................ 13-3
Disassemble ........................................................................ 7-23 Clean ................................................................................... 13-3
Outer Hydraulic Pump Support Drive .................................... 9-53 Symbols .................................................................................... i-2
Assemble ............................................................................. 9-56 Tap-Drill Chart - U.S. Customary and Metric......................... V-54
Disassemble ........................................................................ 9-53 Torque Converter Cooler........................................................ 8-26
Install ................................................................................... 9-55 Clean ................................................................................... 8-28
Pipe Plug Torque Values........................................................ V-53 Disassemble ........................................................................ 8-28
Piston ..................................................................................... 1-60 Exploded View ...................................................................... 8-26
Clean ................................................................................... 1-60 General Information ............................................................. 8-26
Push Rods or Tubes................................................................. 4-7 Turbocharger Heat Shield ..................................................... 10-11
Clean ..................................................................................... 4-7 Clean .................................................................................. 10-11
General Information ............................................................... 4-7 Marine Applications .......................................................... 10-11
Inspect for Reuse ................................................................... 4-7 Inspect for Reuse ............................................................... 10-11
Rear Gear Drive (Lower Assembly)........................................ 9-18 Marine Applications .......................................................... 10-11
Assemble ............................................................................. 9-26 Install .................................................................................. 10-11
Disassemble ........................................................................ 9-25 Marine Applications .......................................................... 10-11
Exploded View ...................................................................... 9-23 Remove .............................................................................. 10-11
Inspect for Reuse ................................................................. 9-26 Marine Applications .......................................................... 10-11
Install ................................................................................... 9-29 Turbocharger, Water-Cooled ................................................. 10-10
Remove ............................................................................... 9-18 Clean .................................................................................. 10-10
Rear Gear Drive (Upper Assembly)........................................ 9-35 Inspect for Reuse ............................................................... 10-10
Assemble ................................................................... 9-42 , 9-50 Valve, Cylinder Head .............................................................. 2-22
Disassemble .............................................................. 9-37 , 9-49 Grind ................................................................................... 2-24
Exploded View ............................................................ 9-35 , 9-48 Inspect for Reuse ................................................................. 2-23
Inspect for Reuse ....................................................... 9-40 , 9-49 Install ................................................................................... 2-26
Rocker Lever ............................................................................ 3-7 Lap ...................................................................................... 2-26
Assemble ............................................................................... 3-9 Magnetic Crack Inspect ........................................................ 2-23
Disassemble .......................................................................... 3-7 Remove ............................................................................... 2-22
Magnetic Crack Inspect ......................................................... 3-8 Valve Guide, Cylinder Head ................................................... 2-18
Rocker Lever Assembly.......................................................... 3-10 Clean ................................................................................... 2-18
Index
Page 5
Inspect ................................................................................. 2-19

Inspect for Reuse ................................................................. 2-18
Install ................................................................................... 2-19
Remove ............................................................................... 2-18
Valve Seat Bore ...................................................................... 2-20
Initial Check ......................................................................... 2-20
Valve Seat Insert, Cylinder Head ........................................... 2-20
Grind .................................................................................... 2-21
Install ................................................................................... 2-21
Remove ............................................................................... 2-20
Vibration Damper ................................................................... 1-63
Clean ................................................................................... 1-63
Water Pump............................................................................ 8-19
Assemble ............................................................................. 8-22
Clean ................................................................................... 8-21
Disassemble ........................................................................ 8-19
Inspect ................................................................................. 8-21
Water Pump Bearings ............................................................ 8-28
Install ................................................................................... 8-29
Measure ............................................................................... 8-28
Remove ............................................................................... 8-28
Water Pump Drive Bushing.................................................... 9-52
Assemble ............................................................................. 9-52
Disassemble ........................................................................ 9-52
Water Pump Drive Gear and Shaft......................................... 9-51
Assemble ............................................................................. 9-52
Disassemble ........................................................................ 9-51
Water Pump Drive Pulley ....................................................... 9-52
Clean ................................................................................... 9-52
ProCarManuals.com

Weights and Measures - Conversion Factors........................ V-55
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 15, COLUMBUS INDIANA
–POSTAGE WILL BE PAID BY ADDRESSEE—
CUMMINS ENGINE COMPANY, INC.

MAIL CODE 41302
BOX 3005
COLUMBUS, IN 47202-3005
Do not use this form to order additional literature. Refer to

ProCarManuals.com
Section L - Service Literature for literature information.

Literature Survey Form
Bulletin No.: 3666232-00
We are always open to any suggestions or recommendations that will aid in improving our manuals. Use
this postage paid survey form to evaluate this manual. Please check the appropriate response and use
the space provided below to list any additional comments:
Yes No
Is the needed information easy to locate in the manual?
Is the information easy to read?
Is the information easy to understand?
Does the information sufficiently cover the subject?
Are subjects in the Index specific enough to locate in the manual?
Are the important points sufficiently emphasized?
Are the illustrations easy to understand?
Does the text support the operation being illustrated?
Do you use the Table of Contents and Section Contents?
Do you use the Index?
Please provide comments on any response(s) marked ″No″ in this survey and on any suggestions you
feel could improve our manuals.
Name:
Company:
Street Address:
City: State/Province:
Country: Zip/Postal Code:
Do not use this form to order additional literature. Refer to

ProCarManuals.com
Section L - Service Literature for literature information.

Box 3005
Columbus, Indiana, U.S.A., 47202
Cable: CUMDIEX COLUMBUS
Registered Office
Cummins Engine Company, Ltd.
46-50 Coombe Road
New Malden,
Surrey KT3 4QL,
England
Cable: CUMEUR G
Registration No. 573951 England
CopyrightR 1997
ProCarManuals.com
Bulletin No. 3666232-00

Printed in U.S.A. 12/97 P35

Cummins Qsk19 Series Diesel Engine Service Repair Manual PDF

Uploaded by

Copyright:

Available Formats

Cummins Qsk19 Series Diesel Engine Service Repair Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cummins Qsk19 Series Diesel Engine Service Repair Manual PDF

Uploaded by

Copyright:

Available Formats

Shop Manual

CopyrightR 1997 Bulletin No. 3666232

Engine Identification .......................................................................................................................... E

Complete Engine – Group 00 ............................................................................................................. 0

Cylinder Block – Group 01 ................................................................................................................. 1

Cylinder Head – Group 02 .................................................................................................................. 2

Rocker Levers – Group 03 .................................................................................................................. 3

Cam Followers/Tappets – Group 04 ................................................................................................... 4

Fuel System – Group 05 ..................................................................................................................... 5

Injectors and Fuel Lines – Group 06 ................................................................................................. 6

Lubricating Oil System – Group 07 .................................................................................................... 7

Cooling System – Group 08 ............................................................................................................... 8

Drive Units – Group 09 ....................................................................................................................... 9

Air Intake System – Group 10 ............................................................................................................ 10

Exhaust System – Group 11 ............................................................................................................... 11

Compressed Air System – Group 12 ................................................................................................. 12

Electrical Equipment – Group 13 ....................................................................................................... 13

Engine Testing – Group 14 ................................................................................................................. 14

Mounting Adaptations – Group 16 ..................................................................................................... 16

Electronic Engine Controls – Group 19 ............................................................................................. 19

Service Literature ............................................................................................................................... L

Component Manufacturers ................................................................................................................. M

About the Manual

The illustrations are intended to show repair or replace-

General Safety Instructions

General Repair Instructions

Air Compressor Flywheel Mounting Capscrews

• Follow all safety instructions noted in the procedures

General Cleaning Instructions

Glass or Plastic Bead Cleaning

Section E - Engine Identification

The engine dataplate shows specific information about the

System Voltage Ambient Temperatures

Batteries (Specific Gravity)

1. Fuel Rail Quick-Disconnect Fitting A. Fan Hub

EXHAUST SIDE - QSK19

1. Coolant Outlet A. Turbocharger

Section 0 - Complete Engine - Group 00

Tool No. Tool Description Tool Illustration

Depth Gauge Assembly

Main Bearing Cap Pulley

Drill Ream Fixture

Piston Ring Expander

Tool No. Tool Description Tool Illustration

Liner Installation Tool

Crack Detection Kit

Injection Timing Tool

Universal Injector Timing Tool Fixture Kit Update

Light Duty Puller Kit

Universal Liner Puller

Tool No. Tool Description Tool Illustration

Camshaft Bushing Tool Hydraulic Actuator Kit

Camshaft Bushing Installation/Removal Kit

Camshaft Gear Puller Kit

Main Bearing Roll-out Tool

Torque Wrench Adapter

Tool No. Tool Description Tool Illustration

Light Duty Puller Kit

Valve Setting Gauge Kit