VLT 2800 Quick Reference Guide

■ Parameter list ■ Status messages Parameter- Selection/range Factory Setting

This list can be used for checking and F r # description setting
making a note of your parameter settings. The frequency converter shows the present 001 Language [0]=English, [1]=German, [2]=French, [0]=English
The list can be folded and placed in the output frequency in Hertz [Hz]. [3]=Danish, [4]=Spanish, [5]=Italian
enclosed plastic folder. 002 Local/remote [0]=Remote operation, [0]=Remote
I o operation [1]=Local operation operation
■ Control keys The frequency converter shows the present 003 Local reference 0-fMAX / RefMIN-RefMAX / -RefMAX - +RefMAX 000,000.000
[QUICK MENU] gives access to output current in Amps [A].
the parameters used in the 004 Active Setup [0]=Factory Setup, [1]=Setup 1, [1]=Setup 1
Quick menu. The [QUICK [2]=Setup 2, [3]=Setup 3, [4]=Setup 4,
U o [5]=Multi Setup
MENU] key is also used if a change of a The frequency converter shows the present
parameter value is not to be carried out. 005 Programming [0]=Factory Setup, [1]=Setup 1, [5]=Active Setup
output voltage in Volts [V].
Setup [2]=Setup 2, [3]=Setup 3, [4]=Setup 4,
See also [QUICK MENU] + [+].
[5]=Active Setup
U d 006 Setup See manual [0]=No copying
[CHANGE DATA] is used for The frequency converter shows the copying
changing a setting. The intermediate circuit voltage in Volts [V]. 007 LCP copy [0]=No copying, [1]=Upload all [0]=No copying
[CHANGE DATA] key is also parameters, [2]=Download all para-
used for confirming the change of a meters, [3]=Download power-
P o
parameter setting. The frequency converter shows the independent parameters
calculated output power in kilowatts [kW]. 008 Display scaling of 0.01 - 100.00 1.00
[+] / [-] are used for selecting a output frequency
parameter and for changing 009 Large display See manual [4]=Frequency
notrun readout [Hz]
the chosen parameter value. This message is displayed if an attempt is
010 Small display See manual [1]=Reference
These keys are also used in made to change a parameter value, while readout 1.1 [%]
Display mode for switching the motor is running. Stop the motor to 011 Small display See manual [6]=Motor
between operating variable change the parameter value. readout 1.2 current [A]
read-outs. 012 Small display See manual [8]=Power [kW]
LCP readout 1.3
[QUICK MENU]+[+] This message is shown if an LCP 2 control 013 Local control [0]=Local not active, [4]=Remote
keys must be pressed unit has been installed and the [QUICK [1]=Local control and open loop, operated control
simultaneously to give MENU] or [CHANGE DATA] key has been [2]=Remote operated control and open as par. 100
access to all activated. loop, [3]=Local control as par. 100,
[4]=Remote operated control as par. 100
parameters. With an LCP 2 unit installed, it is only
014 Local stop/Reset [0]=Not active, [1]=Active [1]=Active
possible to change parameters via this unit.
[STOP/RESET] is used for 015 Local jog [0]=Not active, [1]=Active [0]=Not active
stopping the connected motor or Err.
for resetting the frequency A warning or alarm will be shown by means 016 Local reversing [0]=Not active, [1]=Active [0]=Not active
converter after a trip. of a digit code on the display, e.g. Err
13. A warning will be shown on the 017 Local reset [0]=Not active, [1]=Active [1]=Active
[START] is used for starting the display until the fault has been corrected, of trip
frequency converter. Is always and an alarm will flash until [RESET] is 018 Lock for [0]=Not locked, [1]=Locked [0]=Not locked
active, but the [START] key data change
activated.
019 Operating mode [0]=Auto restart, use saved ref. [1]=Forced stop,
cannot override a stop command.
at power-up, [1]=Forced stop, use saved ref. use saved ref.
Ha local operation [2]=Forced stop, set ref. to 0
The frequency converter shows the present 020 Lock for Hand [0]=Not active, disable [1]=Active, enable
Hand mode reference in Herz [Hz]. mode [1]=Active, enable
024 User-defined [0]=Not active, [1]=Active [0]=Not active
Quick Menu
■ Warnings/alarm messages 025 Quick Menu [Index 1-20] 000
The list below gives a description of the Setup Value 0-999
different warnings and alarms. 100 Configuration [0]=Speed regulation, open loop [0]=Speed
After a Trip locked, the mains supply must [1]=Speed regulation, closed loop regulation,
[3]=Process regulation, closed loop open loop
be disconnected and the fault must be
101 Torque [1]=Constant torque [1]=Constant
corrected. Connect the mains supply again characteristic [2]=Variable torque, low torque
and reset the frequency converter. The [3]=Variable torque, medium
frequency converter is now ready for [4]=Variable torque, high
operation. [5]=Variable torque, low CT start
A Trip can be reset manually in three [6]=Variable torque, medium CT start
different ways: [7]=Variable torque, high CT start
- Via the control key [STOP/RESET] [8]=Special motor characteristic
- Via a digital input. 102 Motor power PM,N 0.37-11 kW Depends on unit
103 Motor 200-240 V/380-480 V Depends on unit
- Via serial communication.
voltage UM,N
104 Motor 24-1000 Hz 50 Hz
The manual gives a description of the frequency fM,N
different faults. 105 Motor 0.01-IMAX Depends on
current IM,N choice of motor
No. 2 Live zero fault 106 Rated 100-fM,N x 60 (max. 60000 rpm) Depends on
No. 4 Mains phase fault motor speed choice of motor
No. 5 Voltage warning high 107 Automatic [0]=Optimisation off [0]=Optimisation
No. 6 Voltage warning low motor tuning [2]=Optimisation on off
No. 7 Overvoltage 108 Stator 0.000-X.XXX Ω Depends on
resistance RS choice of motor
No. 8 Undervoltage
109 Stator 0.00-X.XX Ω Depends on
No. 9 Inverter overload
reactance XS choice of motor
No. 10 Motor overload 119 High start torque 0.0 - 0.5 sec. 0.0 sec.
No. 11 Motor thermistor
No. 12 Current limit 120 Start delay 0.0-10.0 sec. 0.0 sec.
No. 13 Overcurrent 121 Start function [0]=DC hold during start delay time [2]=Coasting
No. 14 Earth fault [1]=DC brake during start delay time during start
No. 15 Switch mode fault [2]=Coasting during start delay time delay time
No. 16 Short-circuit [3]=Start frequency/voltage clockwise
No. 17 Serial communication time-out [4]=Start frequency/voltage in reference
No. 18 HPFB bus time-out direction
122 Function at stop [0]=Coasting [0]=Coasting
No. 33 Out of frequency range
[1]=DC hold
No. 34 HPFB communication fault 123 Min. frequency 0.1 - 10.0 Hz 0.1 Hz
No. 35 Inrush fault for activating of
No. 36 Overload temperature function at stop
Nos. 37-45 Internal faults 126 DC brake time 0-60 sec. 10 sec.
No. 50 AMT RS outside limit
No. 51 AMT fault re. nameplate data 127 DC brake cut-in 0.0 (OFF) - par. 202. Output frequency OFF
No. 52 AMT faulty motor phase frequency high limit, fMAX
No. 53 AMT motor too small 128 Motor thermal See manual [0]=No
protection protection
No. 54 AMT incorrect motor
130 Start frequency 0.0-10.0 Hz 0.0 Hz
No. 55 AMT timeout
No. 56 AMT warning during AMT 131 Voltage at start 0.0 - 200.0 V 0.0 V
No. 99 Locked

MG.28.D5.02 - VLT is a registered Danfoss trademark 195R0033

 Parameter- Selection/range Factory Setting Parameter- Selection/range Factory Setting
# description setting # description setting
132 DC brake 0-100% of max. DC brake voltage 0% 310 Term. 53, Max. 0 - 10.0 V 10.0 V
voltage scaling
133 Start voltage 0.00-100.00 V Depends on unit 314 Term. 60, analo- [0]=No operation, [1]=Reference [0]=No operation
gue input current [2]=Feedback
134 Load 0.00-300.0% 100,0% 315 Term. 60, Min. 0.0 - 20.0 mA 0.0 mA
compensation scaling
135 U/f ratio 0.00-20.0 at Hz Depends on unit 316 Term. 60, Max. 0.0 - 20.0 mA 20.0 mA
scaling
136 Slip -500 - +500% of rated 100% 317 Time out 1 - 99 sec. 10 sec.
compensation slip compensation
137 DC 0-100% of max. DC hold voltage 0% 318 Function after [0]=No operation, [1]=Freeze output [0]=No operation
hold voltage time out frequency, [2]=Stop, [3]=Jog,
138 Brake cut 0.5 - 132.0/1000.0 Hz 3.0 Hz [4]=Max. speed, [5]=Stop and trip
out value 319 Term. 42, See manual [7] = 0-IINV.
139 Brake cut 0.5 - 132.0/1000.0 Hz 3.0 Hz analogue output 0-20 mA
in frequency 323 Relay output See manual [1]=Drive ready
140 Current, minimum 0 - 100% of Within 0% 327 Pulse/reference 150 - 67600 Hz 5000 Hz
value feedback
142 Spread 0.000-XXX.XXX Ω Depends on 341 Term. 46, See manual [1]=Drive ready
reactance choice of motor digital output
143 Internal fan [0]=Automatic, [1]=Always switched [0] = Automatic 342 Term. 46, Max.
control on, [2]=Always switched off pulse output 150 - 10,000 Hz 5000 Hz
144 Gain AC brake 1.0 - 1.50 1.30 343 Precise stop See manual [0] = Normal
146 Reset voltage [0]=Off [0]=Off function ramp stop
vector [1]=Reset 344 Counter value 1 - 999999 100000 pulses
349 Speed comp 0 - 100 ms 10 ms
200 Output [0]=Only clockwise, 0-132 Hz [0]=Only clock- delay
frequency range [1]=Both directions, 0-132 Hz wise, 0-132 Hz 400 Brake function [0]=Off, [1]=Resistor brake Depends on unit
[2]=Only anti-clockwise, 0-132 Hz [4] AC brake, [5]=Load sharing
[3]=Only clockwise, 0-1000 Hz 405 Reset function See manual [0]=Manual reset
[4]=Both directions, 0-1000 Hz
[5]=Only anti-clockwise, 0-1000 Hz 406 Automatic 0 - 10 sec. 5 sec.
201 Output frequency 0.0 - fMAX 0.0 Hz restart time
low limit, fMIN 409 Trip delay 0 - 60 sec. (61=OFF) OFF
202 Output frequency fMIN - 132/1000 Hz 132 Hz overcurrent
high limit, fMAX 411 Switching 3000 - 14000 Hz 4500 Hz
203 Reference/ [0]=Min. ref./fb - Max. ref./fb [0]=Min. ref./fb - frequency
feedback range [1]=-Max. ref./fb - Max. ref./fb Max. ref./fb 412 Output frequency [2] = No LC-filter [2] = No LC-filter
204 Min. reference Par. 100 Config. = Open loop [0] 0.000 Hz dependent [3] = LC-filter fitted
RefMIN - 100,000.000 - par. 205 Ref MAX switching
Par. 100 Config. = Closed loop [1]/[3] 0.000 413 Overmodulation [0]=Off, [1]=On [1]=On
- Par. 414 Min. fb - Par. 205 RefMAX function
205 Max. reference Par. 100 Config. = Open loop [0] 50.000 Hz 414 Min. feedback, -100,000.000 - par. 415 FBMAX 0.000
RefMAX Par. 204 Ref MIN-1000.000 Hz FBMIN
Par. 100 Config. = Closed loop [1]/[3] 50.000 415 Max. feedback, par. 414 FB MIN - 100,000.000 1500.000
Par. 204 Ref MIN- Par. 415 Max. fb FBMAX
206 Ramp type [0]=Linear [1]=Sine-shaped [0]=Linear 416 Process units See manual [0]=No unit
[2]=Sine- 2shaped
207 Ramp-up time 1 0.02-3600 sec. 3.00 sec. 417 Speed PID pro- 0.000 (OFF) - 1.000 0.010
portional gain
208 Ramp-down 0.02-3600 sec. 3.00 sec. 418 Speed PID 20.00 - 999.99 ms (1000 = OFF) 100.00 ms
time 1 integral time
209 Ramp-up time 2 0.02-3600 sec. 3.00 sec. 419 Speed PID 0.00 (OFF) - 200.00 ms 20 ms
differential time
210 Ramp-down 0.02-3600 sec. 3.00 sec. 420 Speed PID 5.0 - 50.0 5.0
time 2 D-gain limit
211 Jog ramp time 0.02-3600 sec. 3.00 sec. 421 Speed PID 20 - 500 ms 20 ms
lowpass filter time
212 Quick stop 0.02-3600 sec. 3.00 sec. 423 U1 voltage 0.0 - 999.0 V par. 103
ramp-down time
213 Jog frequency 0.0- Par. 202 Output frequency 10.0 Hz 424 F1 frequency 0.0 - par. 426 F2 frequency par. 104
high limit Motor frequency
214 Reference [0]=Sum [0]=Sum 425 U2 0voltage 0.0 - 999,0 V par. 103
function [1]=Relative
[2]=External/preset 426 F2 frequency Par. 424 F1 frequency - par. 104
215 Preset ref. 1 -100.00% - + 100.00% 0.00% par. 428 F3 frequency Motor frequency
427 U3 voltage 0.0 - 999.0 V 0.0 V
216 Preset ref. 2 -100.00% - + 100.00% 0.00%
428 F3 frequency Par. 426 F2 frequency - 1000 Hz par. 104
217 Preset ref. 3 -100.00% - + 100.00% 0.00% Motor frequency
437 Process PID [0]=Normal, [1]=Inverse [0]=Normal
218 Preset ref. 4 -100.00% - + 100.00% 0.00% Normal/inverse
control
219 Catch up/slow 0.00-100% of the current reference 0.00% 438 Process PID [0]=Not active, [1]=Active [1]=Active
down reference anti windup
221 Current limit, [A] = x-xxx.x% of IMAX 160% 439 Process PID fMIN - fMAX (par. 201/202) Par. 201 Output
ILIM start frequency frequency low
223 Warning: 0.0 - Par. 224 Warning: High current, 0.0 A limit, fMIN
Low current IHIGH 440 Process PID 0.0 - 10.00 0.01
224 Warning: Par. 223 Warning: Low current, IMAX proportional gain
High current ILOW - IMAX
225 Warning: 0.0 - par. 226 Warning: High frequency, 0.0 Hz 441 Process PID 0.01 - 9999.99 ms (OFF) OFF
Low frequency fHIGH integration time
226 Warning: Par 225 f LOW - 120/1000 Hz 132.0 Hz 442 Process PID 0.00 (OFF) - 10.00 sec. 0.00 sec.
High frequency differentiation time
227 Warning: 100,000.000 - par. 228 -4000.000 443 Process PID diff. 5.0 - 50.0 5.0
Low feedback, Warning: FBHIGH gain limit
FBLOW 444 Process PID 0.02 - 10.00 0.02
228 Warning: Par. 227 - Warning: 4000.000 lowpass filter time
High feedback, FBLOW - 100,000.000 445 Flying start [0]=Off, [1]=OK same direction, [0]=OFF
FBHIGH [2]=OK both directions,
229 Frequency bypass, 0 (OFF) - fMAX 0 Hz [3]=DC brake and start
bandwidth 451 FF factor 0 - 500% 100%
230 Frequency 0 -132/1000 Hz 0.0 Hz
bypass 1 452 Controller 0 - 200% 10%
231 Frequency 0 -132/1000 Hz 0.0 Hz range
bypass 2 456 Brake voltage 0 - 25 V if 200V device 0
302 Digital input See manual [7]=Start reduce 0 - 50 V if 400V device 0
Terminal 18
303 Digital input See manual [9]=Reversing
Terminal 19
304 Digital input See manual [3]=Reset and
Terminal 27
305 Digital input See manual
coasting inverse
[13]=Jog
Terminal Rail Layout
Terminal 29
307 Digital input See manual [0]=No operation
Terminal 33
308 Term. 53, analo- [0]=No operation, [1]=Reference [1]=Reference
gue input voltage [2]=Feedback
309 Term. 53, Min. 0.00 - 10.0 V 0.0 V
scaling

Electronic Power Solutions Pty Ltd | 3/42 Deakin St, Brendale 4500, Qld, Australia | www.electronicpowersolutions.com | 1300 797 655 195R0033
Leaders in Electronic Motor Control