Elect 5
Elect 5
Elect 5
1) Splitting project into tasks and estimate time and resources required to complete each task is called
a) project scheduling
b) project optimization
c) project control
2) the OP-AMP circit shown performs the function of
a) simplification
b) integration
c) differentiation
d) summing
e) attenuation
3) a copper cable used in a plain old telephone service line has a loss of 1.5 dB/km. What is the approximate
loss experienced if the user is located 1.5km from the central office?
a) 1.5 dB
b) 15 dB
c) 20 dB
d) 220 dB
4) A lossy transmission line is used to connect a transmitter to an antenna. If the VSWR measured at the
antenna end tof the transmission line is 1.5. which of the following statements is correct?
a) The VSWR measured at the transmitter end of the transmission line is smaller than 1.5.
b) The VSWR measured at the transmitter end of the transmission line is greater than 1.5.
c) The VSWR measured at the transmitter end of the transmission line is equal 1.5.
d) The characteristic impedance of the antenna matches exactl the characteristic impedance of the
transmission line
5) A motor is equipped with an optical shaft encoder to measure motor speed. The optical encoder provides
200 pulses per motor revolution. A microcontroller equipped with a real-time interrupt (RTI)capability is
used to measure motor speed. The RTI interval is 32.768 ms. The microcontroller counts 372 pulses from
the optical encoder in the RTI interval. The speed rpm of the motor is
a) 33
b) 568
c) 3276
d) 3400
6) Referring to the figure the voltage V across till: 50-U resistor is :
Hint: ω=2πf
a) 35
b) 51
c) 71
d) 92
7) Software maintenance activities can be classified into several maintenance types. Which of the following
is not a soft ware maintenance type
a) Adaptive maintenance
b) Corrective maintenance
c) Customer-initiated maintenance
d) Perfective maintenance
8) Your boss has just approved the initiationof a project to celebrate Qatara€TMS national day . sadia has
been assigned the project manger as should be
a) Establish the reporting process to the boss
b) Work on the project scope
c) Make a report on reqired cost for the project
d) Develop the project charter to do the project
e) Ask the boss as to how many team members would be allowed in the project
9) With respect to relational record based data models at the user level, a relation is represented in a
a) Key
b) List
c) Queue
d) Table
10) In optical communication frequency division multiplexing (FDM ) is called?
a) Polarization-division multiplexing (PDM)
b) Space-division multiplexing (SDM)
c) Single-sideband modulation (SSB)
d) Wavelength division multiplexing (WDM)
11) In the receiver of a wireless system we must amplify the received signal using
a) A power amplifier
b) A differential amplifier
c) An active filter
d) A low noise amplifier
12) Of the following wngineering disciplines, who would be BEST suited to design and operate an automobile
factory
a) Petroleum engineer
b) Mechanical engineer
c) Civil engineer
d) Chemical engineer
13) If the souce voltge in the circuit shown is v = 100sin 377t, the peak reverse voltage applied to the diode
would
14) A room with a floor area of 50ft × 30ft and a ceiling height of 10 ft has luinaires suspended 2 ft from the
ceiling. Assuming a working plane of 30 in and a reqired illumination levelof 50 fc, the net luminous flux
(lumens) using fixtures with a coefficient of utilization of 0.78 is most nearly
a) 48000
b) 58000
c) 75000
d) 96000
15) Increasing the current withdrawn from a battery has what effect on the battery capacity and why?
a) Increased capacity which is cased by less internal hear loss
b) Increased capacity which is caused by lower internal resistance
c) Decreased capacity which is caused by higher load voltage drop
d) Decreased capacity which is caused by increased polarization
16) Consider the oscillator circit shown below. This circuit uses which resonsnt mode (s) of the crystal XI
a) Serries resonant
b) Parallel resonant
c) Series-parallel resonant
d) Not resonant
17) The resistance of 100 W , 200 V tamp is
a) 100 ohm
b) 200 ohm
c) 400 ohm
d) 1600 ohm
18) A de current of 50 A is flowing ina long isolated wire. The magnitude of the magnetic field intensity.
H(A/m), 10 cm from the center of the wire is
a) 0.05
b) 8
c) 43
d) 80
19) Which of the following chices is not one of the stages of a project life cycle?
a) Concept
b) Initiation
c) Planning
d) Execution
e) Delivery / closure
20) The main cause for transformer humming is
a) Vibrations in the insulating and cooling oil
b) Vibrations int he core laminations
c) Vibrations in the bushes
d) None of the above
21) Ina cascade amplifier, to reduce the loading effect at the output the output impedance of the last stage
should be
a) Very high
b) Intermediate
c) Very small
22) While machine operation, the slip of the symchronous machine is a€a€. . .
a) High
b) Low
c) Zero
d) One
23) Field-programmable gate arrays (FPGAs) and other array logic devices normally contain numerous flip
flops. These flip-flops are generally of the type
a) D
b) J-K
c) S-R
d) T
24) Which of the following statements does not represent ohm’s law?
a) Current / potential difference = constant
b) Potential difference / current = constant
c) Potential difference = current × resistance
d) Current = resistance × potential difference
25) Strength of material may be defined as
a) The maximum internal resistance offered by the materials to the externally applied force
b) Capability of materials to absorb strain energy
c) Capability of materials to do work
d) The maximum internal resistance offered by the materials against deformation
26) The spinning reserve is the
a) Generating capacity that is connected to the grid and ready to take the load
b) Generating capacity that is available for service but ot in operation
c) Generating capacity under maintenance
d) None of the above