TECH SHEET - DO NOT DISCARD PAGE 1

WARNING IMPORTANT
Electrical Shock Hazard Electrostatic Discharge (ESD)
Sensitive Electronics
Disconnect power before servicing.
ESD problems are present everywhere. ESD may
Replace all parts and panels before damage or weaken the electronic control assembly.
operating. The new control assembly may appear to work well
Failure to do so can result in death or after repair is finished, but failure may occur at a
electrical shock. later date due to ESD stress.
■ Use an anti-static wrist strap. Connect wrist
DIAGNOSTICS strap to green ground connection point or
unpainted metal in the appliance
■ Is oven in “Sabbath Mode”? If so “SAB” will appear in -OR-
digital display. Press and hold “6” key for 5 seconds Touch your finger repeatedly to a green ground
to end Sabbath Mode. connection point or unpainted metal in the
appliance.
Disconnect power and perform the following checks:
■ Before removing the part from its package,
■ The most common cause for control failure is touch the anti-static bag to a green ground
corrosion on connectors. Therefore, disconnecting connection point or unpainted metal in the
and reconnecting wires will be necessary throughout appliance.
test procedures.
■ Avoid touching electronic parts or terminal
■ All tests/checks should be made with a VOM or DVM contacts; handle electronic control assembly by
having a sensitivity of 20,000 ohms per volt DC or edges only.
greater.
■ When repackaging failed electronic control
■ Check all connections before replacing components, assembly in anti-static bag, observe above
looking for broken or loose wires, failed terminals, or instructions.
wires not pressed into connectors far enough.
■ Resistance checks must be made with power cord
unplugged from outlet, and with wiring harness or 2. Size is shown in display - “id 30”.
connectors disconnected.
3. Press CLOCK SET/START pad until correct size is
■ To check for last five Fault Codes: Press and hold displayed.
“0” key to access previous codes. Numeric keys
0-4 indicate faults 1-5 respectively, with “0” being the 4. Press CANCEL pad (do not press the OVEN START key).
most recent code. 5. Press and hold “1” pad for 5 seconds to verify
programming.
Fahrenheit (° F) to Celsius (° C)
Conversion PROBLEM: Bake Temperature Needs
The default is Fahrenheit (° F). Adjustment
1. Press the BROIL pad for 5 seconds. The temperature 1. Press BAKE pad for 5 seconds. The default temp. 0° or
will be displayed in degrees Celsius indicated by the a previously entered offset temperature will show in
“C” in the temperature display. the Temperature Display.
2. To return the display to degrees Fahrenheit press the 2. Press the BAKE pad to increase the temperature in
BROIL pad again for 5 seconds. “F” will show in the 5° F or 3° C increments.
temperature display. Press the BROIL pad to decrease the temperature in
5° F or 3° C increments.
Programming the Cavity Size NOTE: Maximum offset temperature adjustment is
1. When replacing the electronic control, be sure to ±35° F or ±21° C.
program the cavity size within 60 seconds of power up 3. Press the START pad to save the temperature
by pressing the following touchpads: adjustment.
BAKE (upper half of BAKE key),
CONVECTION BROIL (lower half of BROIL key),
STOP TIME, CONV FULL MEAL, digit #7, digit #9,
TIMER SET/START, START.

FOR SERVICE TECHNICIAN'S USE ONLY PART NO. 8302067

PAGE 2 TECH SHEET - DO NOT DISCARD

NOTES:
■ Always disconnect power before touching internal
parts of the oven!
■ Upon replacement, immediately return old electronic
oven control using the mailing label supplied with
each new control.

FAILURE/ERROR DISPLAY CODES

FAULT ERROR
CODE EXPLANATION RECOMMENDED REPAIR PROCEDURE
CODE CODE
Will only be displayed if user presses and holds “CANCEL” key for
F0 Default F code - no failure
5 seconds and there is no pre-existing fault. Press CANCEL to clear display.
All E
F1 Electronic control malfunction Replace control.
Codes
E0 Key held down too long, or key is shorted
1. Check keypad connector for firm connection.
F2 E1 Keypad keytail not connected 2. Press CANCEL. If error code returns after 60 sec., replace keypad.
3. Replace control.
E5 CANCEL key drive line open
Temperature sensor opened –
E0
R=2875 ohm (by spec)
1. Check sensor connection.
Temperature sensor shorted – 2. Measure sensor resistance: 1080Ω at 70° F (21° C). (Add 2Ω per
E1
R=825 ohm (by spec) degree F).
F3 3. If resistance is not valid, replace sensor.
Oven temp too high – over 575° F (302° C)
E2 4. If sensor resistance and connections are good, then check for welded-
in COOK mode
closed relays on the control.
Oven temp too high – over 950° F (510° C)
E3
in CLEAN mode
1. Disconnect meat probe and measure probe resistance:
78kΩ at 60°F (16°C); 37kΩ at 90°F (32°C)
2. If resistance is not valid, replace probe.
F4 E1 Meat probe malfunction – shorted
3. Insert probe and check for a firm connection between probe and jack
(in oven cavity).
4. Check connection between jack and harness (in rear of oven).
1. Check the latch assembly: latch arm pivot joint, arm/motor connection,
plunger and hook springs.
Door is open, but latch is locked (condition 2. Check the Latch Motor:
exists when door switch is open indicating - Check for firm electrical connections.
E0 an open door, and latch switch is closed - Disconnect the two wires from the motor and measure the resistance
indicating a locked door) of the motor. The resistance should be approximately 2450Ω. If the
motor is open (∞Ω) or shorted (0Ω), it should be replaced.
F5 3. Check the Latch Switch. Disconnect it and use a continuity tester:
- Door latched = switch closed, continuity should read 0Ω.
- Door unlatched = switch open, continuity should read ∞Ω.
4. Check Door Open/Closed Switch. Disconnect it and use a continuity tester:
- Door open = switch open, continuity should read ∞Ω.
E1 Self-clean latch will not lock/unlock - Door closed = switch closed, continuity should read 0Ω.
5. Check power and element connections.
6. Replace control.

PART NO. 8302067 FOR SERVICE TECHNICIAN'S USE ONLY

 TECH SHEET - DO NOT DISCARD PAGE 3

WIRE HARNESS SCHEMATIC

NOTES:
■ When replacing the electronic control, be sure to
program the cavity size. See “Programming the Cavity
Size” on page 1.
■ Dots indicate connections or splices.
■ Circuit shown in STANDBY/OFF mode with oven door
closed.

ELECTRONIC FILTER - WP #4451985 N L2 L1

CONTROL POWER
TRANSFORMER
W R BK
R
BU
BU
R BK W

BK
L1
P3-5 P3-7 P3-2 P3-3
BK P4-1 W W
ELECTRONIC P1-3
BK P4-2 CONTROL
BK P1-1 GY
P6-4 W W
M
~
DOOR LOCK
W V MOTOR LATCH
P7-4 P6-6 BK BK
TEMP SENSOR
1080 W AT 70°F (21°C) t°
1654 W AT 350°F (177°C) W V THERMAL
P7-5 CONVECTION
MODELS ONLY
W Y P1-6 OR W
P7-8
MEAT PROBE
78k W AT 60°F (15.6°C) t° CONV. FAN
W GN P7-7 Y CONV.-1600W
37k W AT 90°F (32.2°C) P5-4 Y
R

P5-3 R BAKE-2000W R R
THERMAL CONVECTION
MODELS ONLY
BU OUT BROIL-1000W OVEN
DOOR (ON LATCH ASSY) P5-1 SHUTDOWN
BU
SWITCH THERMAL
TAN BR FUSE
P7-2 OR IN BROIL-1667W
P5-2 OR
LATCH
SWITCH
(OPERATED BY NON-CONVECTION
MOTOR) BU MODELS ONLY
P7-3 R
TAN DOUBLE LINE R
R
BREAK RELAY

P1-5 GY W

RETURN LINE MUST BE CONNECTED LIGHT POWER SUPPLY

P7-1 BLOWER
P1-9 BK W
HALOGEN
BK 5W/BULB
P3-1 BK W BK W

GN W

FOR SERVICE TECHNICIAN'S USE ONLY PART NO. 8302067

PAGE 4 TECH SHEET - DO NOT DISCARD

OVEN COMPONENTS ELECTRICAL COMPONENTS KEY

FRONT / REAR
OVEN COMPONENT
SERVICEABLE
ELECTRONIC CONTROL FRONT
MEMBRANE SWITCH FRONT
DOOR SWITCH FRONT
LATCH SWITCH FRONT
LATCH MOTOR FRONT
PROBE - FRONT
MEAT PROBE SENSOR
JACK - REAR
OVEN TEMPERATURE SENSOR FRONT
CONSOLE BLOWER REAR
LIGHT BULB - FRONT
HALOGEN LIGHTS
LIGHT ASSY. - REAR
CAVITY LIGHT TRANSFORMER FRONT
CONVECTION FAN MOTOR REAR
THERMAL FUSE/T.O.D. REAR
BAKE ELEMENT REAR
OUTER BROIL ELEMENT FRONT
INNER BROIL ELEMENT FRONT
CONVECTION RING ELEMENT FRONT
CONTROL POWER TRANSFORMER FRONT
ELECTRONIC FILTER FRONT

RELAY LOGIC UPPER

AND LOWER OVEN

RELAY LOGIC
KEY

PART NO. 8302067 FOR SERVICE TECHNICIAN'S USE ONLY

TECH SHEET - DO NOT DISCARD PAGE 5

OVEN SHUTDOWN THERMAL FUSE

Thermal Fuse Opening Reclose Marking
The oven shutdown thermal fuse Part No. Temp. °F Temp. °F (with Black Letters)
is located at the back of the oven. 4452223 266°F ± 10°F Pink/Wht Stripe
It will shut down the elements if the
4451442 248°F+18°F to 248°F – 0°F Yellow/Wht Stripe
temperature at the back of the oven
exceeds component limits. 4450934 338°F ± 11.7°F Red
–31°F
4450334 275°F ± 11.7°F Orange/Wht Stripe
Verify that the oven shutdown thermal MAX
fuse is OK. 4450250 320°F ± 11.7°F Blue
4450249 302°F ± 11.7°F Green/Wht Stripe
To replace this thermal fuse, refer to chart at right for
correct part number. 8300802 230°F+18°F to 230°F – 0°F Blue/Wht Stripe

THE FOLLOWING COMPONENTS CAN BE TESTED AT THE CONTROL PANEL*:

FRONT/REAR CHECK
COMPONENTS RESULTS
SERVICEABLE POINTS
Door Open = Open Circuit
Door Switch Front P7-2 (BR) to P7-1 (TAN)
Door Closed = Closed Circuit
Door Lock Motor (with Door Closed) Front P6-4 (GY) to P6-6 (BK) 2500 Ω
Oven Temperature Sensor Front P7-4 (V) to P7-5 (V) 1080 Ω @ 70°F (21°C)
Blower Rear P1-5 (GY) to Neutral (W) 14 Ω to 18 Ω
Primary Winding 40 Ω to 45 Ω
Oven Light Transformer Front
Secondary Winding Less than 1 Ω
Oven Shutdown Thermal Fuse Rear P5-2 (OR) to (R) Wire at Double Line Break Relay Closed Circuit
Bake Element Rear P5-3 (R) to (R) Wire at Double Line Break Relay 25 Ω to 30 Ω
Inner Broil Element Front P5-2 (OR) to (R) Wire at Double Line Break Relay 31 Ω to 36 Ω
Outer Broil Element Front P5-1 (BU) to (R) Wire at Double Line Break Relay 53 Ω to 59 Ω
Convection Ring Element Front P5-4 (Y) to (R) Wire at Double Line Break Relay 33 Ω to 37 Ω
Convection Fan Motor Rear P1-6 (OR) to Neutral (W) 8 Ω to 12 Ω
Door Unlocked = Open Circuit
Latch Switch Front P7-3 (BU) to P7-1 (TAN)
Door Locked = Closed Circuit
Probe into jack – check for
Meat Probe Jack Rear P7-7 (GN) to P7-8 (Y)
78kΩ at room temperature

* Short double line break relay red wire terminals fastons

FOR SERVICE TECHNICIAN'S USE ONLY PART NO. 8302067

PAGE 6 TECH SHEET - DO NOT DISCARD

OVEN STRIP CIRCUITS The following individual circuits are for use in diagnosis.
Before starting diagnosis, check the line voltage and for blown fuses.

BAKE AND OVEN

PREHEAT-BAKE SHUTDOWN N L2
BAKE-2000W
L1 P5-3 R R THERMAL
FUSE

BK P4-1 P5-1 BU OUT BROIL-1000W R

BK P4-2 BU
P5-2 OR OR

R IN BROIL-1667W

R R
DOUBLE LINE
BREAK RELAY P1-5 GY W
M
~
BLOWER
BK P1-1

ECONO BROIL

MAXI BROIL

CLEAN DOOR LOCK N L2 L1

MOTOR LATCH
DOOR ON LATCH ASSY
SWITCH GY
TAN BR P6-4 M W W
P7-2 ~
LATCH (OPERATED BY P6-6 BK BK
SWITCH MOTOR)
TAN BU OVEN
P7-3
SHUTDOWN
RETURN LINE MUST BE CONNECTED
P7-1 BAKE-2000W THERMAL
P5-3 R R
L1 FUSE
BK P4-1
BU OUT BROIL-1000W R
P5-1
BK P4-2
BU
P5-2 OR OR
IN BROIL-1667W
R
DOUBLE LINE R R
BREAK RELAY
P1-5 GY M W
~
BK P1-1 BLOWER

PART NO. 8302067 FOR SERVICE TECHNICIAN'S USE ONLY

TECH SHEET - DO NOT DISCARD PAGE 7

OVEN STRIP CIRCUITS The following individual circuits are for use in diagnosis.
Before starting diagnosis, check the line voltage and for blown fuses.

CONVECTION BROIL OVEN N L2

SHUTDOWN
OUT BROIL-1000W THERMAL
(THERMAL P5-1 BU
FUSE
CONVECTION L1
BU
P5-2 OR OR R
MODELS, ONLY)
BK P4-1 IN BROIL-1667W
R
BK P4-2 R R
DOUBLE LINE
BREAK RELAY P1-5 GY W
M
~
BLOWER
BK P1-1 P1-6 OR W
M
~
CONV. FAN

CONVECTION ROAST OVEN

SHUTDOWN
N L2

AND PREHEAT- P5-3 R BAKE-2000W

R Y THERMAL
FUSE
CONVECTION BAKE L1 P5-1 BU OUT BROIL-1000W R
(THERMAL BK P4-1 P5-2 OR
BU
OR
CONVECTION
P4-2 IN BROIL-1667W
MODELS, ONLY) BK
R
DOUBLE LINE R R
BREAK RELAY
P1-5 GY W
M
~
P1-1 BLOWER
BK P1-6 OR W
M
~
CONV. FAN

CONVECTION BAKE
(THERMAL
CONVECTION
MODELS, ONLY)
(BAKE ELEMENT USED
30” MODELS ONLY)

FOR SERVICE TECHNICIAN'S USE ONLY PART NO. 8302067

PAGE 8 TECH SHEET - DO NOT DISCARD

MANUFACTURED UNDER ONE OR MORE OF THE

FOLLOWING UNITED STATES PATENTS:
4,102,322 4,364,589 4,467,184
OTHER PATENTS PENDING

PART NO. 8302067 FOR SERVICE TECHNICIAN'S USE ONLY