Scribd
Upload
255 views6 pages

Protocolo OSPF

The document describes the configuration of interfaces, IP addresses, routing protocols and DHCP pools on a router. Key steps include: 1. Configuring interfaces FastEthernet 0/0, 0/1 and 1/0 with IP addresses and enabling them. 2. Configuring DHCP pools FEC, FAQ, FTC, FIT and FIQ with corresponding network addresses, default routers and DNS servers. 3. Configuring OSPF routing protocol with networks in area 0.

Uploaded by

NoelCastrillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
255 views6 pages

Protocolo OSPF

The document describes the configuration of interfaces, IP addresses, routing protocols and DHCP pools on a router. Key steps include: 1. Configuring interfaces FastEthernet 0/0, 0/1 and 1/0 with IP addresses and enabling them. 2. Configuring DHCP pools FEC, FAQ, FTC, FIT and FIQ with corresponding network addresses, default routers and DNS servers. 3. Configuring OSPF routing protocol with networks in area 0.

Uploaded by

NoelCastrillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 6

Press RETURN to get started!

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 192.168.1.129 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#do write
Building configuration...
[OK]
Router(config-if)#exit
Router(config)#interface fastEthernet 0/1
Router(config-if)#ip address 192.168.1.65 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to


up

Router(config-if)#exit
Router(config)#interface fastEthernet 1/0
Router(config-if)#ip address 192.168.1.1 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to


up

Router(config-if)#do write
Building configuration...
[OK]
Router(config-if)#exit
Router(config)#do write
Building configuration...
[OK]
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up

Router con0 is now available


Press RETURN to get started.

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#IP dhcp pool FEC
Router(dhcp-config)#Network 192.168.1.64 255.255.255.224
Router(dhcp-config)#default-router 192.168.1.65
Router(dhcp-config)#dns-server 192.168.1.65
Router(dhcp-config)#do wirte
Translating "wirte"...domain server (255.255.255.255)
% Unknown command or computer name, or unable to find computer address

Router(dhcp-config)#do write
Building configuration...
[OK]
Router(dhcp-config)#exit

Router(config)#ip dhcp pool FAQ


Router(dhcp-config)#Network 192.168.1.0 255.255.255.224

Router(dhcp-config)#default-router 192.168.1.1
Router(dhcp-config)#dns-server 192.168.1.1
Router(dhcp-config)#do write
Building configuration...
[OK]
Router(dhcp-config)#exit
Router(config)#%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged
192.168.1.65.
%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.1.1.

Router(config)#config terminal
%Invalid hex value
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#no ip domain lookup


^
% Invalid input detected at '^' marker.

Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip domain lookup
Router(config)#exit

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#interface fastethernet0/0
Router(config-if)#ip address 192.168.1.130 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to


up

Router(config-if)#exit
Router(config)#interface fastethernet0/1
Router(config-if)#ip address 192.168.1.97 255.255.225.224
Bad mask 0xFFFFE1E0 for address 192.168.1.97
Router(config-if)#ip address 192.168.1.97 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to


up

Router(config-if)#exit
Router(config)#interface fastethernet1/0
Router(config-if)#ip addess 192.168.1.161 255.255.255.244
^
% Invalid input detected at '^' marker.

Router(config-if)#ip address 192.168.1.161 255.255.255.244


Bad mask 0xFFFFFFF4 for address 192.168.1.161
Router(config-if)#ip address 192.168.1.161 255.255.255.224
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to


up

Router(config-if)#exit
Router(config)#interface fastethernet1/1
Router(config-if)#ip address 192.168.1.33 255.255.255
^
% Invalid input detected at '^' marker.

Router(config-if)#ip address 192.168.1.33 255.255.255.224


Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to
up

Router(config-if)#exit
Router(config)#do write
Building configuration...
[OK]
Router(config)#

Router con0 is now available

Press RETURN to get started.

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip domain lookup
Router(config)#ip dhcp pool FTC
Router(dhcp-config)#Network 192.168.1.96 255.255.255.224
Router(dhcp-config)#default-router 192.168.1.97
Router(dhcp-config)#dns-server 192.168.1.97
Router(dhcp-config)#do write
Building configuration...
[OK]
Router(dhcp-config)#exit
Router(config)#ip dhcp pool FIT
Router(dhcp-config)#Network 192.168.1.160 255.255.255.224
Router(dhcp-config)#default-router 192.168.1.161
Router(dhcp-config)#dns-server 192.168.1.161
Router(dhcp-config)#do write
Building configuration...
[OK]
Router(dhcp-config)#exit
Router(config)#ip dhcp pool FIQ
Router(dhcp-config)#Network 192.168.1.32 255.255.255.224
Router(dhcp-config)#default-router 192.168.1.33
Router(dhcp-config)#dns-server 192.168.1.33
Router(dhcp-config)#do write
Building configuration...
[OK]
Router(dhcp-config)#eixt
^
% Invalid input detected at '^' marker.

Router(dhcp-config)#exit
Router(config)#%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged
192.168.1.97.
%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.1.161.
%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged 192.168.1.33.

Router(config)#
Router#
%SYS-5-CONFIG_I: Configured from console by console
09:49 19/10/2019
Router#

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 1
Router(config-router)#Network 192.168.1.128 0.0.0.31 area 0
Router(config-router)#Network 192.168.1.64 0.0.0.31 area 0
Router(config-router)#Network 192.168.1.0 0.0.0.31 area 0
Router(config-router)#do write
Building configuration...
[OK]
Router(config-router)#
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 1
Router(config-router)#Network 192.168.1.128 0.0.0.31 area 0
Router(config-router)#Network 192.168.1.128 0.0.0.31 area 0
01:34:29: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.1.129 on FastEthernet0/0 from
LOADING to FULL, Loading Done

Router(config-router)#Network 192.168.1.96 0.0.0.31 area 0


Router(config-router)#Network 192.168.1.96 0.0.0.160 area 0
OSPF: Invalid address/mask combination (discontiguous mask)
Router(config-router)#Network 192.168.1.160 0.0.0.31 area 0
Router(config-router)#Network 192.168.1.32 0.0.0.31 area 0
Router(config-router)#do write
Building configuration...
[OK]
Router(config-router)#exit
Router(config)#
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#

You might also like