INFORMATION

Electric Actuator/Rod Type

AC Servo Motor (400 W) Size: 63 Dust/Drip proof (IP65) specification (options
Select
) RoHS

Motor mounting position can be selected from 4 directions!

New New New

Top mounting Right side parallel Left side parallel In-line

Max. work load (kg) New Top/Parallel In-line

Horizontal 200 80
Vertical 115 72

Max. pushing force (N)

New Top/Parallel 3343
In-line 1910

Max. speed: 1000 mm/s

* 500 stroke
 ust/Drip proof specification:
D Rod end brackets
Equivalent to IP65 Single Double Simple
knuckle joint knuckle joint joint
Application

Scraper
Prevents foreign matter
from entering.
Scraper
For checking the limit and intermediate signal
Groove for auto switch Applicable to the D-M9 and D-M9W (2-color indication)
* The auto switches should be ordered separately.

2-color indication solid state auto switch

Lifter Appropriate setting of the mounting Operating ON
position can be performed without range OFF
mistakes.
Red Green Red
A green light
Auto switch lights up at Optimum operating range
the optimum
operating range.

Offering 4 types of   AC servo motor drivers

Incremental type Absolute type

Pulse input type/ CC-Link

Positioning type Pulse input type direct input type SSCNET# type
Series LECSA Series LECSB Series LECSC Series LECSS

Series LEY
13-E607
Series LEY

Speed–Work Load Graph

Vertical transfer Horizontal transfer
LEY63 LEY63
120 250
Lead 2.86: LEY63L
Lead 2.86:
100 (Top/Parallel type only)

Horizontal work load [kg]

200 LEY63L
Vertical work load [kg]

(Top/Parallel type only)

80 Lead 5: LEY63C
Regeneration (100%) 150
60 /High load
Lead 10: Lead 5:
Lead 10:
LEY63B 100 LEY63C
40 Regeneration (50%) LEY63B Lead 20:
Lead 20:
LEY63A LEY63A
Regeneration (100%) 50
20
/Low load
0 0
0 200 400 600 800 1000 1200 1400 0 200 400 600 800 1000 1200
Speed [mm/s] Speed [mm/s]

Required conditions for “Regeneration option”

* Regeneration option required when using product above “Regeneration”
line in graph. (Order separately) “Regeneration Option” Models
Size Regenerative conditions Vertical transfer Horizontal transfer
[How to read the graph] Regeneration (50%) LEC-MR-RB-032
Required conditions change depending on operating conditions.
LEY63 Regeneration (100%)/Low load LEC-MR-RB-032 Not required
“Regeneration (50%)” : Duty ratio 50% or more
“Regeneration (100%)”: Duty ratio 100% Regeneration (100%)/High load LEC-MR-RB-12

Allowable Stroke Speed

[mm/s]
AC servo Lead Stroke [mm]
Model
motor Symbol [mm] 100 200 300 400 500 600 700 800
A 20 1000 800 600 500
B 10 500 400 300 250
C 5 250 200 150 125
LEY63 400 W/60
(Motor rotation speed) (3000 rpm) (2400 rpm) (1800 rpm) (1500 rpm)
L 2.86 70
(Motor rotation speed) (1470 rpm)

Force Conversion Graph Graph of Allowable Lateral Load on the Rod End
LEY63 100
Allowable lateral load on the rod end: F (N)

3500

3000 Lead 2.86: LEY63L

(Top/Parallel type only)
2500
Lead 5: LEY63C LEY63
Force [N]

2000
10
1500
Lead 10: LEY63B
1000

500
Lead 20: LEY63A
0 1
10 20 30 40 50 60
0 100 200 300 400 500 600 700 800 900 1000
Torque limit/Command value [%]
Stroke [mm]
Torque limit/Command value [%] Duty ratio [%] Continuous pushing time [minute]
25 or less 100 —
— (1.5)
[Stroke] = [Product stroke] + [Distance from the rod end to the
30 100 (60)
center of gravity of the workpiece]
40 50 (30) 1.5 (0.5)
50 30 (20) 0.5 (0.16) F

* 1 The values in ( ) are for a closely-mounted driver.

* 2 When limiting torque with incremental encoder, parameter No. PC12/
the value of the internal torque command should be set 50% or less.
* 3 When limiting torque with absolute encoder, parameter No. PC13/the
value of the maximum output command for analog torque should be Center of gravity
set 50% or less.

1
 Electric Actuator/Rod Type

Series LEY
LEY63 RoHS

How to Order

LEY 63 S4 B 200 S 2 A2
q w e r t y u i o !0 !1 !2 !3

q Size e Motor type r Lead [mm]

63 Output Actuator Compatible Symbol LEY63
Symbol Type
[W] size drivers A 20
w Motor mounting position S4
AC servo motor
400 63 LECSA2-S4
B 10
(Incremental encoder) C 5
Nil Top mounting
LECSB2-S8 L 2.86*
R Right side parallel AC servo motor
S8 400 63 LECSC2-S8 * Screw lead 5 mm, Pulley ratio [4:7]
L Left side parallel (Absolute encoder)
LECSS2-S8 equivalent lead
D In-line
* Only available for top mounting and
right/left side parallel types.
t Stroke [mm] y Dust/Drip proof u Motor option i Rod end thread
100 100 Nil IP5x (Dust proof specification) Nil Without option Nil Rod end female thread
to to IP65 (Dust/Drip proof specification)/ B With lock Rod end male thread
P With vent hole tap
M (1 rod end nut is included.)
800 800
* When using the dust/drip proof (lP65), correctly
mount the fitting and tubing to the vent hole
tap, and then place the end of the tubing in an
area not exposed to dust or water.
* T he fitting and tubing should be provided
separately by the customer. Select [Applicable
tubing O.D.: ø4 or more, Connection thread:
Rc1/8].
o Mounting*1 !0 Cable type Note 1)
Motor mounting position *1 Mounting bracket is shipped together, (but Nil Without cable
Symbol Type not assembled).
Top/Parallel In-line
*2 For horizontal cantilever mounting with the
S Standard cable
Nil Ends tapped (Standard)*2   rod flange and ends tapped, use the actuator R Robotic cable (Flexible cable)
U Body bottom tapped   within the following stroke range. Note 1) T
 he motor and encoder cables
L Foot  — • LEY63: 400 or less are included. (The lock cable is
*3 For mounting with the double clevis, use the also included when the motor
F Rod flange*2   actuator within the following stroke range. with lock option is selected.)
D Double clevis*3  — • LEY63: 300 or less

!1 Cable length Note 2) [m] !2 Driver type

Nil Without cable Compatible drivers Power supply voltage * When the driver type is selected, the cable is included.
Select cable type and cable length.
2 2 Nil Without driver
Example) S2S2 : Standard cable (2 m) + Driver (LECSS2)
5 5 LECSA2/Pulse input S2 : Standard cable (2 m)
A2 (Incremental encoder)
200 V to 230 V
A 10 Nil : Without cable and driver
Note 2) T he length of the LECSB2/Pulse input
encoder, motor and
B2 (Absolute encoder)
200 V to 230 V
lock cables are the
LECSC2/CC-Link
same. C2 (Absolute encoder)
200 V to 230 V

LECSS2/SSCNET#
S2 (Absolute encoder)
200 V to 230 V

!3 I/O connector * Applicable stroke table

Stroke Manufacturable
Nil Without connector (mm) 100 200 300 400 500 600 700 800 stroke range
Model
H With connector
LEY63         50 to 800
Note) Consult with SMC for the manufacture of intermediate strokes.
2
Series LEY

Specifications

Model LEY63S48  (Top/Parallel) LEY63DS48  (In-line)

Stroke [mm] Note 1) 100, 200, 300, 400, 500, 600, 700, 800
Horizontal Note 2) 40 70 80 200 40 70 80
Work load [kg]
Vertical 19 38 72 115 19 38 72
Pushing force [N]/Set value Note 3) : 15 to 50% Note 4) 156 to 521 304 to 1,012 573 to 1,910 1,003 to 3,343 156 to 521 304 to 1,012 573 to 1,910
Note 5)
Up to 500 1000 500 250 1000 500 250
Max. speed Stroke 505 to 600 800 400 200 800 400 200
Actuator specifications

70
[mm/s] range 605 to 700 600 300 150 600 300 150
705 to 800 500 250 125 500 250 125
Pushing speed [mm/s] Note 6) 30 or less
Max. acceleration/deceleration [mm/s2] 5,000 3,000 5,000
Positioning repeatability [mm] ±0.02
Screw lead [mm] (including pulley ratio) 20 10 5 5 (2.86) 20 10 5
Impact/Vibration resistance [m/s2] Note 7) 50/20
Actuation type Ball screw Ball screw + Belt [Pulley ratio 4:7] Ball screw
Guide type Sliding bushing (Piston rod)
Operating temperature range [°C] 5 to 40
Operating humidity range [%RH] 90 or less (No condensation)
Required conditions for Note 8) Horizontal Not required Not required Not required Not required Not required Not required Not required
“Regeneration option” [kg] Vertical 2 or more 5 or more 12 or more 46 or more 2 or more 5 or more 12 or more
Motor output/Size 400 W/60
Lock unit specifications Electric specifications

Motor type AC servo motor (200 VAC)

Motor type S4: Incremental 17-bit encoder (Resolution: 131072 p/rev)
Encoder
Motor type S8: Absolute 18-bit encoder (Resolution: 262144 p/rev)
Horizontal 210
Power consumption [W] Note 9)
Vertical 230
Standby power consumption Horizontal 2
when operating [W] Note 10) Vertical 18
Max. instantaneous power consumption [W] Note 11) 1275
Type Note 12) Non-magnetizing lock
Holding force [N] 313 607 1,146 2,006 313 607 1,146
Power consumption [W] at 20°C Note 13) 7.9
0
Rated voltage [V] 24 VDC−10%
Note 1) Consult with SMC for non-standard strokes as they are produced as special orders.
Note 2) The maximum value of the horizontal work load. An external guide is necessary to support the load. The actual work load changes according to the
condition of the external guide. Please confirm using actual device.
Note 3) Set values for the driver.
Note 4) The force setting range (set values for the driver) for the pushing operation with the torque control mode etc. The pushing force and duty ratio
change according to the set value. Set it with reference to “Force Conversion Graph” on page 1.
Note 5) The allowable speed changes according to the stroke.
Note 6) The allowable collision speed for the pushing operation with the torque control mode etc.
Note 7) Impact resistance: No malfunction occurred when the actuator was tested with a drop tester in both an axial direction and a perpendicular direction
to the lead screw. (Test was performed with the actuator in the initial state.)
Vibration resistance: N o malfunction occurred in a test ranging between 45 to 2000 Hz. Test was performed in both an axial direction and a
perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.)
Note 8) The work load conditions which require “Regeneration option” when operating at the maximum speed (Duty ratio: 100%).
Note 9) The power consumption (including the driver) is for when the actuator is operating.
Note 10) The standby power consumption when operating (including the driver) is for when the actuator is stopped in the set position during the operation.
Note 11) The maximum instantaneous power consumption (including the driver) is for when the actuator is operating.
Note 12) Only when motor option “With lock” is selected.
Note 13) For an actuator with lock, add the power consumption for the lock.

Weights

Product Weights [kg] Additional Weights [kg]

Series LEY63S (Motor mounting position: Top/Parallel) Size 63
Stroke [mm] 100 200 300 400 500 600 700 800 Incremental encoder 0.4
Lock
Incremental Absolute encoder 0.6
Motor type

5.4 6.6 8.3 9.4 10.5 12.2 13.4 14.5

encoder Rod end Male thread 0.12
Absolute male thread Nut 0.04
5.5 6.7 8.4 9.5 10.6 12.3 13.5 14.6
encoder Foot (2 sets including mounting bolt) 0.26
Rod flange (including mounting bolt) 0.51
Series LEY63DS (Motor mounting position: In-line)
Double clevis (including pin,
Stroke [mm] 100 200 300 400 500 600 700 800 retaining ring and mounting bolt)
0.58
Incremental
Motor type

5.6 6.7 8.4 9.6 10.7 12.4 13.5 14.7

encoder
Absolute
5.7 6.8 8.5 9.7 10.8 12.5 13.6 14.8
encoder

3
 Electric Actuator/Rod Type Series LEY

Construction
Motor top mounting type: LEY63

@4 @3

Cable is shipped together.

!8

o @2 @1 !0 @8
!9

!3

!7

!6 !5 y q w t !4 r e i u !1 @0 !2

In-line motor type: LEY63D

@8 @7

@6 @5
When rod end male thread selected
@9 #0 @9 @4

Component Parts
No. Description Material Note No. Description Material Note
1 Body Aluminum alloy Anodized 16 Wear ring Resin
2 Ball screw shaft Alloy steel 17 Screw shaft pulley Aluminum alloy
3 Ball screw nut Resin/Alloy steel 18 Motor pulley Aluminum alloy
4 Piston Aluminum alloy 19 Belt —
5 Piston rod Stainless steel Hard chrome anodized 20 Lock nut Alloy steel Hard chrome anodized
6 Rod cover Aluminum alloy 21 Seal NBR
7 Bearing holder Stainless steel 22 Retaining ring Steel for spring
8 Rotation stopper Resin 23 Motor adapter Aluminum alloy Coating
9 Socket Free cutting carbon steel Nickel plating 24 Motor —
10 Bushing Lead bronze cast 25 Socket (Male thread) Free cutting carbon steel Nickel plating
11 Bearing — 26 Nut Alloy steel Trivalent chromated
12 Return box Aluminum alloy Coating 27 Motor block Aluminum alloy Coating
13 Return plate Aluminum alloy Coating 28 Spacer A Stainless steel
14 Magnet — 29 Hub Aluminum alloy
15 Wear ring holder Stainless steel 30 Spider Urethane

Replacement Parts (Top/Parallel only)/Belt

No. Size Lead Order no.
A/B/C LE-D-2-5
19 63
L LE-D-2-6

4
 Series LEY

Dimensions: Motor Top/Parallel

ZZ
X
W

Z
Encoder Z phase detecting position
4±0.1
Note 1)
Rod operating range
V

Hx2 (Stroke + 8 mm)

thread depth C

T
EV

M
J

øD
K Note 2) 4 x O1 Y M

U
M thread depth R L B + Stroke S 4 x O1
EH A + Stroke thread depth R

IP65 (Dust/Drip proof specification): LEY63-P

Note 1) Range within which the rod can move.
Make sure a workpiece mounted on the rod does not interfere with (View ZZ)
the workpieces and facilities around the rod. Rc1/8
Note 2) The direction of rod end width across flats (K) differs depending Vent hole tap∗
on the products.

18

* When using the dust/drip proof (IP65), correctly mount the fitting and
tubing to the vent hole tap, and then place the end of the tubing in an
area not exposed to dust or water. The fitting and tubing should be
provided separately by the customer.
Select [Applicable tubing O.D.: ø4 or more, Connection thread: Rc1/8].

[mm]
Stroke range
Size
[mm]
A B C D EH EV H J K L M O1 R S Y
Up to 200 192.6 155.2
63 205 to 500 227.6 190.2 21 40 76 82 M16 x 2 44 36 37.4 60 M8 x 1.25 16 80 32.2
505 to 800 262.6 225.2

Incremental encoder Absolute encoder

Stroke range
Size
[mm]
T U V Without lock With lock Without lock With lock
W X Z W X Z W X Z W X Z
Up to 200
11.6 11.6 11.6 11.6
63 205 to 500 146 4 60 110.2 150.2
(12.6)*
138.8 178.8
(12.6)*
98.5 138.5
(12.6)*
138 178
(12.6)*
505 to 800
* The values in ( ) are the dimensions when L is selected for screw lead.

Motor left side parallel type: LEY63L Motor right side parallel type: LEY63R
S1

S1

[mm]
T2 T2
U

Size S1 T2 U
63 84 142 4

Note) When the motor is mounted on the left or right side in parallel, the groove for auto switch on the side to which the motor is mounted is hidden.
A 5
 Electric Actuator/Rod Type Series LEY

Dimensions: In-line Motor

LEY63D
Encoder Z phase detecting position

4±1
Rod operating range Note 1)
(Stroke + 8 mm) ZZ
Z
EV

M
T

øD

4 x O1 thread
K Note 2) V

U
effective depth R L B + Stroke W
M H thread A + Stroke
EH effective depth C
S
Note 1) Range within which the rod can move. Make sure a workpiece
mounted on the rod does not interfere with the workpieces and
facilities around the rod.
Note 2) The direction of rod end width across flats (K) differs depending
on the products.

[mm]
Stroke range
Size
[mm]
C D EH EV H J K L M O1 R S T U
Up to 200
63 205 to 500 21 40 76 82 M16 x 2 44 36 37.4 60 M8 x 1.25 16 78 83 5
505 to 800

Incremental encoder Absolute encoder

Stroke range
Size
[mm]
B V Without lock With lock Without lock With lock
A W Z A W Z A W Z A W Z
Up to 200 190.7 338.3 366.9 326.6 366.1
63 205 to 500 225.7 60 373.3 110.2 8.1 401.9 138.8 8.1 361.6 98.5 8.1 401.1 138 8.1
505 to 800 260.7 408.3 436.9 396.6 436.1

End male thread: LEY63-M IP65 (Dust/Drip proof specification): LEY63D-P

(View ZZ)
Rc1/8
M18 x 1.5

Vent hole tap∗

10.5

Width across flats 27 11

26 50
39
76.4∗

*T
 he measurement 76.4 is when the unit is in the encoder Z * When using the dust/drip proof (IP65), correctly mount the fitting and
phase detecting position. At this position, 4 mm at the end. tubing to the vent hole tap, and then place the end of the tubing in an
area not exposed to dust or water. The fitting and tubing should be
provided separately by the customer.
Select [Applicable tubing O.D.: ø4 or more, Connection thread: Rc1/8].

6
 Dimensions
Body bottom tapped: LEY63-U
Motor top/parallel type In-line motor type
6 x MO 6 x MO thread
øXA H9 depth XA øXA H9 depth XA
thread depth MR effective depth MR
MH

MH
MD MD
MC Section XX MC Section XX
L MA ML + Stroke L MA ML + Stroke Section XX details
[mm]
Size Stroke range [mm] L MA MC MD MH ML MO MR XA XB
50 to 74 24 50
XA H9 XA

XB
75 to 124 45 60.5 65
63 125 to 200 37.4 38 58 67 44 M8 x 1.25 11 6 7
201 to 500 100
86 81
501 to 800 135

Foot: LEY63-L

Outward mounting
3.2
Included parts
29.2 • Foot
• Body mounting bolt

Material: Carbon steel (Chromate

88

5 5
4 x ø9 treated)
50

3.2

* The overall length is when the unit

is in the Z phase first detecting
95 14.2 8
4.3 8 position. At this position, 4 mm at
110 LS + Stroke LS + Stroke 25.2 the end.
LA + Stroke Note) W hen the motor mounting is
the right or left side parallel
Rod flange: LEY63-F type, the head side foot should
28.4 be mounted outwards.
[mm]
Stroke range [mm] LA LS
50 to 200 200.8 133.2
Included parts
201 to 500 235.8 168.2
60
80

• Flange
• Body mounting bolt 501 to 800 270.8 203.2

92 4 x ø9 9 Material: Carbon steel (Nickel plating)

108 * The overall length is when the unit is
in the Z phase first detecting position.
Double clevis: LEY63-D At this position, 4 mm at the end.

8 [mm]
ø14 hole H10 Included parts Stroke range [mm] DA CL
axis d9 • Double clevis 50 to 200 236.6 222.6
• Body mounting bolt 201 to 500 271.6 257.6
• Clevis pin 501 to 800 306.6 292.6
• Retaining ring
22 +0.4
22+0.2 Material: Cast iron (Coating)
37.4 30 14 −0.1
CL + Stroke 44−0.3 * The overall length is when the unit is in the Z phase first
detecting position. At this position, 4 mm at the end.
DA + Stroke