Anup Calculation Sheet
Anup Calculation Sheet
Anup Calculation Sheet
[
Total Depth 1,576 meter 0.00 0.00
Total Hole Volume (no pipe) 1,524 bbl 0.00 0.00
Total Hole Volume (with pipe) 1,461 bbl 0.00 0.00
Annulus Volume 1,376 bbl 0.00 0.00
Total Displacement of pipe 63.06 bbl 0.00 0.00
Total Capacity Of Pipe 85.26 bbl 0.00 0.00
Active Pit 350 bbl ANNULAR VELOCITY (Meters / Minute) MIXING MUDS
Circulating time 15480.48 minutes Gallons / Minute 800 Mud Weight 1 11.20 ppg
In & Out 12488.30 minutes Hole Diameter 12.250 Volume 1 500 bbl
Inside Pipe 728.86 minutes Pipe OD 5.500 Mud Weight 2 6.50 ppg
Bottoms Up 11759.44 minutes Annular Velocity (MPM) 49.9 Volume 2 200 bbl
PUMP OUTPUT (GPM) STROKES - HOLE / ANNULUS / PIPE Mud Weight 3 ppg
Liner Size 6.50 inches Hole Volume 1,523.83
Volume 3 bbl
Stroke Length 12.00 inches Strokes 13,027
Mud Weight 4 ppg
Effeciency 95.00 % Hole Volume With Pipe 1,460.78
Volume 4 bbl
Pump 1 Strokes 1 GPM 4.913 Strokes 12,488
Mud Weight 5 ppg
Pump 2 Strokes GPM 0.000 Annulus Volume 1,375.52
Volume 5 bbl
Pump 3 Strokes (Booster) GPM 0.000 Strokes 11,759
Total Volume 700 bbl
Total Strokes 1 Strokes Pipe Volume 85.26
New Mud Wht 9.857 ppg
Barrels / Minute 0.1170 Barrels Strokes 729
Barrels / Stroke 0.1170 Barrels Barrels Strokes Minutes Hours
Gallons / Stroke 0.0028
Total GPM 4.9128 GPS 2200 18,808 18808 313.47
WEIGHT INCREASE - BARITE WEIGHT REDUCTION BOTTOM HOLE PRESSURE vs MUD WEIGHT
Original Mud Weight 10.05 ppg Desired Weight 14.80 ppg Mud Weight = 1 or Pressure = 2 2
Desired Mud Weight 10.40 ppg Density of Oil/Water 6.70 ppg Choose Between Field = 1 or SI Units = 2 2
Pit Volume 400 bbl 15.50 ppg
### Final Volume 405.578 bbl Original Volume 1680.00 bbl True Vertical Depth 2254.00 m 7395.01 ft
Lb Barite 8199.2 lbs Water/Oil To Add 145.19 bbl Mud Weight 1.60 SG 13.31 ppg
MT Barite 3.7 mt Total Mud 1825.19 bbl Bttm Hole Pressure 352.54 bar 5111.88 psi
bbls Barite 5.6 bbl C° 100.00 F° 212.00
sx Barite (100 lb/sx) 82.0 sxs F° 212.00 C° 100.00 WEIGHT INCREASE - DIFFERENT WGT MATERIAL
WEIGHT INCREASE - CALCIUM CARB. WEIGHT INCREASE - FERROX SG of Weight Material 2.15 sg
Original Mud Weight 13.50 ppg Original Mud Weight 9.50 ppg Desired Weight 1.82 sg
Desired Mud Weight 14.00 ppg Desired Mud Weight 10.80 ppg Original Weight 1.8 sg
Pit Volume 40 bbl Pit Volume 500 bbl Original Volume 80 m³
Final Volume 42.224 bbl Final Volume 523.050 bbl Total M³ of weight material 4.85 M³
Lb CaCO3 2147.8 lbs Lb Ferrox 37916.7 lbs Kilos / M³ of weight material 130.30 kg
MT CaCO3 1.0 mt MT Ferrox 17.2 mt Total MT weight material to use 10.42 MT
bbl CaCO3 2.2 bbl bbls Ferrox 23.0 bbl
sx CaCO3 (55 lb/sx) 39.1 sxs sx Ferrox (100 lb/sx) 379.2 sxs Barite 4.20 sg
INCREASE OIL CONTENT DECREASE OIL CONTENT Calcium Carbonate 2.70 sg
Mud Volume 2300 bbls Mud Volume 190 bbls Calcium Chloride 2.15 sg
Oil % (retort) 54 % Oil % (retort) 47.5 % Ferrox 4.70 sg
Water % (retort) 33 % Water % (retort) 15.75 % Flowate 2.16 sg
Solids % (retort) 13 % Solids % (retort) 36.75 % Potassium Carbonate 2.40 sg
Weight (ppg) 10.5 ppg Weight 16.5 ppg Potassium Chloride 1.99 sg
SG of base fluid 0.78 SG SG of Brine / Water 1 SG Sodium Bromide 3.21 sg
Oil Ratio Reqd 68 % Oil Ratio Required 70 % Sodium Chloride 2.17 sg
Oil Required 371 bbls Brine/Water Required 9 bbls
New Volume 2671 bbls New Volume 199 bbls DYNAMIC SAG TEST - VST CALCULATIONS
New Weight 9.95 ppg New Weight 16.1 ppg Mud used to fill sample cup is taken from heating cup at 50°C while
Fann Model 35 is running at specified rpm
% CALCIUM CHLORIDE STROKES - KILL / CHOKE / BOOSTER Begin at 600 rpm, 50°C degrees temperature, 5 min
CaCl2 % W/W 22.0 Initial Choke Line - ID inches 3.000 Rotate 100 rpm, 30 min
CaCl2 % W/W 23.2 Reqd. Volume 30.94 Lower thermocup and start sampling
Purity 97.0 % Strokes 264 Weight of 10 cc syringe:
Mud Volume 2700 bbls Kill Line - ID inches 3.000 Weight of 10 cc syringe with mud, top of thermocup, in grams:
Water 22.0 % Volume 30.94 MW Top (sp.gr.)
CaCl2 Required 79 25 kg sxs Strokes 264 Weight of 10 cc syringe with mud, bottom of thermocup, in grams:
Total Weight 1.98730572 mt Booster Line - ID inches 3.326 MWBottom (sp.gr.)
Total Weight 1987.30572 kg Volume 38.03 Delta Mud Weight, (sp.gr.) = MWTop - MWBottom
Total Weight 901.43596 lbs Strokes 325 Sag Index
TIME TO TD / ROP
Time Started 10/28/07 9:00 AM
Time Now 2/5/20 8:15 AM
107591.25
Depth Started 665 meters
Depth Now 3,235 meters
TD 3900 meters
Speed mt/hr 10.00 hour
Left to TD 665 meters
Time to TD 12.20 hour
0.51 days
Meters Drilled 2,570 meters
MUD ON THE FLY CALCULATIONS
Volume 10000 bbls Discharge rate Heavy Mud Water Total
Required Mud
Density 10.4 ppg GPM GPM GPM bbls/min
Heavy mud Water 550 117 433 13.1
Volume bbls 2134.8 7865.2 575 123 452 13.7
Density ppg 17.4 8.5 600 128 472 14.3
Discharge rate Heavy Mud Water Total 625 133 492 14.9
GPM GPM GPM bbls/min 650 139 511 15.5
25 5 20 0.6 675 144 531 16.1
50 11 39 1.2 700 149 551 16.7
75 16 59 1.8 725 155 570 17.3
100 21 79 2.4 750 160 590 17.9
125 27 98 3.0 775 165 610 18.5
150 32 118 3.6 800 171 629 19.0
175 37 138 4.2 825 176 649 19.6
200 43 157 4.8 850 181 669 20.2
225 48 177 5.4 875 187 688 20.8
250 53 197 6.0 900 192 708 21.4
275 59 216 6.5 925 197 728 22.0
300 64 236 7.1 950 203 747 22.6
325 69 256 7.7 975 208 767 23.2
350 75 275 8.3 1000 213 787 23.8
375 80 295 8.9 1025 219 806 24.4
400 85 315 9.5 1050 224 826 25.0
425 91 334 10.1 1075 229 846 25.6
450 96 354 10.7 1100 235 865 26.2
475 101 374 11.3 1125 240 885 26.8
500 107 393 11.9 1150 246 904 27.4
525 112 413 12.5 1175 251 924 28.0
CONVERTION FACTORS
To Convert To Multiply By To Convert To Multiply By WATER PHASE SALINITY
Atmospheres kg/cm2 1.033 kPa psi 0.145 Total Chlorides
Atmospheres psi 14.7 kPa / m psi / ft 0.04423 ml AgNO3
bar psi 14.5 lb kg 0.4535 % Water
bbl M³ 0.159 lb / 100ft² Pa 0.4788 Cl- in water phase
bbl / ft m³ / m 0.5216 lb / bbl g / l (kg / m³) 2.853
C° F° (C° x 1,8) + 32 lb / ft kg / m 1.49
cm in 0.3937 lb / ft - sec cP 1.488
cP lb / ft - sec 0.00067 lb / ft³ g / l (kg / m³) 16.02 Common Chemical Formulas
F° C° (F°-32)/1,8 lb / gal kg /m³ 119.83 Aluminium Oxide
ft m 0.3048 lb / gal SG 0.12 Barite
ft² m² 0.0929 lb / gal kg / l 0.1198 Barium Carbonate
ft³ m³ 0.0283 liter ft³ 0.03531 Barium Hydroxide
ft³ liter (l) 28.32 liter gal 0.2642 Calcium Carbonate
g/l lb / bbl 0.3505 m ft³ 3.28 Calcium Chloride
g/l lb / ft³ 0.0624 m² ft² 10.76 Calsium Oxide
gal m³ 0.00379 m³ bbl 6.289 Caustic Soda
gal liter (l) 3.785 m³ ft³ 35.31 Gypsum or Anhydrite
in cm 2.54 m³ gal 264.2 Hydrochloric Acid
kg lb 2.205 m³ qt 3448 Hydrogen Sulfide
kg / cm² atmosphere 0.9678 m³ / m bbl / ft 1.917 Lime
kg / cm² psi 14.29 miles km 1.609 Mag. Hydroxide
kg / l lb / gal 9.347 Pa lb / 100 ft² 2.089 Magnessium Oxide
kg / m lb / ft 0.6711 psi atmosphere 0.068 Nitric Acid
kg / m³ lb / bbl 0.3505 psi kg /cm² 0.07 Phosphate (STP)
kg / m³ lb / ft³ 0.06242 psi kPa 6.895 Potassium Chloride
kg / m³ lb / gal 0.00835 psi / ft kPa / m 22.61 SAPP Na2H2
km miles 0.6215 SG lb / gal 8.333 Silicon Dioxide
CONTAMINATION TREATMENT OIL ON CUTTINGS
Contaminant Ion To Remove 1 mg/l kg/m³ lb/bbl Retort cell (empty) 827 grams
Gypsum Calsium Soda Ash - Hold pH 0.00265 0.000928 Retort cell (full) 887 grams
or (Ca) SAPP - Reduce pH 0.00277 0.000971 Measuring Cyl (empty) 58 grams
Anhydrite Bicarb - hold or reduce pH 0.0021 0.000735 Measuring Cyl (full) 71 grams
Lime or Calsium Bicarb 3,23816* 1,135* Retorted Water 9 mls
Cement (Ca) SAPP 4,2795* 1,5* Retorted Oil 4 grams
Hydrogen Sulfide Sulfide Keep pH above 10 and 0.0026 0.00091 Weight of dry cuttings 47 grams
(S2-) add sulfide scavenger Oil on Cuttings 8.51 %
Carbon Dioxide Carbonate Gypsum - hold or reduce pH 0.00285 0.001
(CO32-) Lime - raise pH 0.00123 0.000432
Bicarbonate Lime - raise pH 0.00121 0.000424
(HCO3-)
Hard Water Mg2+ Caustic Soda 0.00331 0.00116
Ca2+ Caustic Soda 0.002 0.0007
* Treatment to remove 1 lb/bbl excess Lime
SPECIFIC GRAVITY OF CHEMICALS
Agipac LV/R 1.60 Drilling Starch 0.50 HDF 200 0.812 Nut Plug 1.30 Sodium Bromide
Antisol FL 1.60 Drillout 1.26 HEC 10 1.40 PBS Accelerator 2.60 Sod. Bromide Brine
Anco Therm V 1.44 Drillthin 1.90 Hilube 0.880 PBS Plug 2.00 Sodium Carbonate
Amm. Bisulphite 1.34 Driscal D 1.44 Iron Oxide 4.50 PBS Retarder 1.57 Sod. Lignosulfonate
Aquaflo HV/LV 1.60 Drispac SL/REG 1.60 Ironite Sponge 4.50 Pearl Ash 2.40 Sodiumm Chloride
Aquapac 1.60 EDC 95/11 0.814 KOH 2.04 Pentandial 1.030 Specell FE
Barite 4.20 FD-2364 0,97-1,03 Koplus LL 1.220 Plugsal 2.16 Staflo REG/EXLO
Bentone 128 0.00 FE-P70 1.50 Kwik Seal 1.50 Polypac 1.60 Ultra Seal XP/C
Bentonite 2.50 Finagreen EBL 0.950 Lampac 0.65 Pot. Bicarbonate 2.17 Ven Fyber 201
Borresol FE-P70 1.50 FL7 Plus 1.40 Lime 2.24 Pot. Carbonate 2.40 Ven-Chem 222
Borrewell FE 1.50 Flo-Trol 1.40 Limestone 2.70 Pot. Chloride 1.99 Versapro P/S
Brinewate A 2.16 Flo-Wate 2.16 Liquid Casing 0.74 Pot. Hydroxide 2.04 Versatrol
Calcite 2.70 Flowzan 1.60 Lo-Tork G 0.880 Pottasche 2.40 Versavert F
Calcium Bromide 3.35 Form A Plug 2.00 Magnesium Chloride 1.88 Prempac EX/SL/R 1.60 Versavert M
Calcium Carbonate 2.70 Form A Plug Acc. 2.60 Mica 0.90 Renax 100 1.040 Versavert P
Calcium Chloride 2.15 Form A Plug Ret. 1.57 MIX II 1.55 Rhodopol 23 P 1.50 Versavert S
Calcium Hydroxide 2.24 Geltone II 1.70 Nocal II 1,2-1,5 Rock Salt 2.17 Versavert Vis
Caustic Potash 2.04 Gilsonite 1.05 Novamod LAO 0,75-0,95 Safe-Surf OE 1.000 VG-69
Caustic Soda 2.13 Glide HS 1.000 Novamul LAO 0,91-0,95 Sandseal Coarse 0.49 Walnut
Celpol 1.60 Glimmer 0.90 Novatec B 0.776 Sea Salt 2.17 Wyoming Bentonite
Celpac 1.60 Glute 10 1.030 Novatec F 1.012 Serla Sol Fe 1.50 Xanthan Gum
CF Lignosulfonate 1.50 Glycol DCP 208 1.010 Novatec PE 0.940 Serla Sol Fe 60 1.50 Xanvis
Citric Acid 1.54 Glydril MC 1.010 Novatec SE 0.950 Silicone Defoamer 0,97-1,03 XC Polymer
CMC LV/HV/EHV 1.55 Graphite 2.23 Novathin 0,79-,-0,85 Soda Ash 2.53 Zalo
Diaseal 2.20 G-Seal 2.23 Novawet 0,90-0,95 Sodium Bicarbonate 2.16 Zinc Carbonate
CALCIUM CHLORIDE SALT TABLE
Metric Conversions
NaCl (g/l) = NaCl (ppb) x 2.85714
H2O (ml/L) = H20 (gal/bbl) x 23.8086
NaCl (ppm) = % wt x 10000
mg/l = ppm x specific gravity
Cl (mg/L) = NaCl (mg/L) x 0.6066
NaCl (mg/L) = Cl x 1.65
POTASSIUM CHLORIDE SALT TABLE
KCl ~ H20 ~ KCl ~ Chlorides Vol. inc Crystal.
% Weight SG. PPG
PPB Gal/bbl mg/l mg/l factor point F
1.0 1.005 8.37 3.5 41.80 10000 4756 1.005 31.2
2.0 1.011 8.42 7.1 41.60 20200 9606 1.009 30.3
3.0 1.017 8.47 10.7 41.40 30500 14506 1.013 29.5
4.0 1.024 8.53 14.4 41.30 41000 19499 1.017 28.6
5.0 1.030 8.59 18.1 41.10 51500 24493 1.022 27.8
6.0 1.037 8.64 21.8 40.90 62200 29582 1.026 26.9
7.0 1.044 8.69 25.6 40.70 73000 34718 1.031 26.1
8.0 1.050 8.75 29.4 40.50 84000 39950 1.035 25.2
9.0 1.057 8.80 33.3 40.40 95100 45229 1.039 24.3
10.0 1.063 8.86 37.3 40.20 106300 50556 1.045 23.4
11.0 1.070 8.90 41.2 40.00 117700 55977 1.050 22.4
12.0 1.077 8.97 45.3 39.80 129200 61447 1.055 21.4
13.0 1.084 9.03 49.4 39.60 140900 67011 1.061 20.4
14.0 1.091 9.08 53.5 39.40 152700 72623 1.066 19.4
15.0 1.097 9.12 57.6 39.10 164600 78282 1.072 18.5
16.0 1.104 9.20 61.9 38.90 176700 84038 1.078 17.0
17.0 1.111 9.26 66.1 38.70 188900 89840 1.084 16.0
18.0 1.119 9.32 70.5 38.50 201300 95737 1.090 15.0
19.0 1.126 9.38 74.9 38.30 213900 101730 1.097 14.0
20.0 1.133 9.44 79.3 38.00 226600 107770 1.104 13.0
21.0 1.140 9.51 83.9 37.80 239500 114000 1.111 22.0
22.0 1.147 9.56 88.4 37.60 252400 120040 1.117 34.0
23.0 1.155 9.64 93.1 37.40 265700 126473 1.125 48.0
24.0 1.162 9.68 97.7 37.10 278900 132643 1.132 59.0
Formulas
Salt (lbs/bb water) = Volume increase factor x KCl (ppb)
Specific Gravity = 1.00056 + 1.22832 (10-6) Cl (mg/L)
Volume increase Factor = 1 + (2.775 x 10-7)(Cl)1.105
Metric Conversions
KCl (g/l) = KCl (ppb) x 2.85714
H2O (ml/L) = H20 (gal/bbl) x 23.8086
KCl (ppm) = % wt x 10000
mg/l = ppm x specific gravity
Cl (mg/L) = KCl (mg/L) x 0.476
KCl (mg/L) = Cl x 2.101
K+ (mg/L) = Cl (mg/L) x 1.103
Cl (mg/L) = K+ (mg/L) x 0.907
PUMP OUTPUT (GPM) Booster Pump
Liner Size 6.50 inches
Stroke Length 12.00 inches
Effeciency 97.00 %
Pump 1 Strokes 1 GPM 5.016
Pump 2 Strokes GPM 0.000
Pump 3 Strokes (Booster) GPM 0.000
Total Strokes 1 Strokes
Barrels / Minute 0.1194 Barrels
Barrels / Stroke 0.1194 Barrels
Gallons / Stroke 0.0028
Total GPM 5.0162 GPS
DYNAMIC SAG TEST - VST CALCULATIONS
sed to fill sample cup is taken from heating cup at 50°C while
Model 35 is running at specified rpm
at 600 rpm, 50°C degrees temperature, 5 min
100 rpm, 30 min
thermocup and start sampling
6.2
21.7
1.55
21.9
1.57
0.02
0.503
WATER PHASE SALINITY
76000
7.6
38
193949
HLORIDE
Initial
Reqd.
%
bbls
%
25 kg sxs
MT
Kg
lbs
CONVERTION FACTORS
To Convert To Multiply By To Convert To
Atmospheres kg/cm2 1.03 kPa psi
Atmospheres psi 14.70 kPa / m psi / f
bar psi 14.50 lb kg
bbl M³ 0.16 lb / 100f² Pa
bbl / f m³ / m 0.52 lb / bbl g / l (kg / m³)
C° F° (C° x 1.8) + 32 lb / f kg / m
cm in 0.39 lb / f - sec cP
cP lb / f - sec 0.00 lb / f³ g / l (kg / m³)
F° C° (F°-32)/1.8 lb / gal kg /m³
f m 0.30 lb / gal SG
f² m² 0.09 lb / gal kg / l
f³ m³ 0.03 liter f³
f³ liter (l) 28.32 liter gal
g/l lb / bbl 0.35 m f³
g/l lb / f³ 0.06 m² f²
gal m³ 0.00 m³ bbl
gal liter (l) 3.79 m³ f³
in cm 2.54 m³ gal
kg lb 2.21 m³ qt
kg / cm² atmosphere 0.97 m³ / m bbl / f
kg / cm² psi 14.29 miles km
kg / l lb / gal 9.35 Pa lb / 100 f²
kg / m lb / f 0.67 psi atmosphere
kg / m³ lb / bbl 0.35 psi kg /cm²
kg / m³ lb / f³ 0.06 psi kPa
kg / m³ lb / gal 0.01 psi / f kPa / m
km miles 0.62 SG lb / gal
Multiply By
0.15
0.04
0.45
0.48
2.85
1.49
1.49
16.02
119.83
0.12
0.12
0.04
0.26
3.28
10.76
6.29
35.31
264.20
3448.00
1.92
1.61
2.09
0.07
0.07
6.90
22.61
8.33
Note: To get results change values in BLUE only
Chlorides Calculation:
Input Temperature
Degree C 172.4 Degree F
Degree F -40.0 Degree C
145.241379 Psi
MUD LOST WITH CUTTINGS WORKSHEET
INPUT
6 Hole Diameter (inches)
48 Interval Length (meters drilled)
12.1 Mud Weight (ppg)
0.60 Retort fraction of oil in whole mud (decimal)
9.10% ROC%
6.8 Base Oil Density (ppg)
21.66 Cuttings Density (ppg)
OUTPUT
0.66 Mud on Cuttings Factor
3.64 Mud Lost with Cuttings (bbls)
Dilution due to Evaporation.
Shale SG 2.4
Sand SG 2.6
are output only
in
lb/gal
lb/gal
ft/min
lb/100ft2
cp
in
in
Velocity
m/min 146.2
ft/min 479.68
CHOKE + KILL LINE- ID 3” Capacity – 0.02868 bbls/m
BOOSTER LINE- ID 3.781” Capacity – 0.04556 bbls/m
6 LINER DIA 6 BOOSTER PUMP LINER DIA
0.102 bbls/stk 0.050904 bbls/stk
RIG DD KG# 2
Input data in cells with yellow background. Cells with red text are output only
Shale SG 2.4
Sand SG 2.6
Velocity
m/min 76
ft/min 249.36
Put value
Formula, don't put any value
Solids Analysis for SOBM
MW (ppg) 9.1 Salt Wt% 19.01
Oil (%) 62 Salt Conc. lbs/bbl 24.65
Water (%) 30 Aw 0.83
Solids (%) 8 OWR 67
Cl- (mg/lit) 45000 Brine Wt. 9.754
SG of HGS 4.2 Correted Solids 6.33
SG of Oil 0.78 WPS mg/lit 140475
SG of D Solids 2.6 LGS % 1.76
LGS lbs/bbl 15.98
HGS % 4.57
HGS lbs/bbl 67.22
Avg. SG Solids 3.481