Scribd
Upload
185 views2 pages

Wind Load Calculation

wind load calculation

Uploaded by

surbhi kumari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
185 views2 pages

Wind Load Calculation

wind load calculation

Uploaded by

surbhi kumari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 2
Examples on revised IS 875 (Part 3) Example 21- Wind Forces on a Sign Board Hoarding Problem Statement: Calculate wind pressure and design forces on a hoarding 10m long and Sm high, to be fixed at the roof of a 24m high building near Cannaught Place area in New Delhi, The base of the hoarding board is 2.0m above the roof level, See figure 21.1 Figure 21.1 Wind Data: (1S:875-pt.3, Sec 5.3.2.2, Table-2) 1. Wind Zone: Zone IV (i= 47m’s) Topography factor “ks = 1.00 (1S:875.pt3, Fig. 1, Sec 5.2) (18:875-pt3, Sec 5.3.3.1) 2. Terrain category: Category 3 (near City Center) Importance factor for Cyclonic Region *ks=1.00 (USi875-pt3, See 5.3.2.1) (1S:875-pt.3, See 5.3.4) Wind Directionality factor *K,'=0.90 Design Factors: (S:875-pt.3, See 6.1.1) Risk Coefficient factor ‘Ar’ o7* Area Averaging factor “Ky” Lor (1S:875-pt.3, See 5.3.1, Table-1) (S:875-pt3, See 6.1.2, Table-4) Terrain & Height factor ‘k;? 1.05** * : considering design life of yrs. IITK-GSDMA-WINDO6-V3.0 87 Examples on revised IS 875 (Part 3) ‘**: For average height of the hoarding, 28.5 m *** : considering tributary area = 5 x20 10.0m, for the design of Frame supports Design Wind Pressure Design Wind Speed = Vz= Vay xkyxiksxy 470,71 1.05%1,0%1.0 = 35.04 mis (1S:875-pt.3, See 5.3) Px = 0.6 (Ve = 0.6x (35.04)? = 736,62 Nim? (IS:875-pt.3, See 5.4) Pa= pe KyxK,0.73720.9 1.00 0.6633 Nima? (1S:875-pt.3, See 6.1) F=C;xA ps (IS:875-pt.3, See 6.3) Wind Fore on Hoarding Since the length of hoarding is 10m, b/h = 10/5 2.0 and the hoarding is 2m above root, Cy= 1.2 (1S:875-pt.3, Table 21) Design Wind Force on hoarding, therefore F~ 1.2 x10 x 0,6633 x 5.0 ~ 3.98 KN acting at (2 2.5)=4.5m_ above roof To allow for oblique winds, force coefficients of 1,7 and 0.44 are to be taken at two ends, as per section 6.3.4.1] Accordingly, 3.98 x 1.7/1.2 = 5.64 KN at windward edge and 3.98 x0.44/1.2 = 1.46 KN at leeward edge shall be considered, per meter width of hoarding. Pressure distribution In vertical direction the wind force may be considered constant over the height, ‘The hoarding sheet will be designed for a force of 5.645 = 1.128 Kim? The frame of hoarding will be designed for average pressure intensity depending on the spacing of vertical frames. IITK-GSDMA-WINDO6-V3.0 88

You might also like