Guide To Making Percussion Caps2

Guide to making blackpowder percussion caps
3-5-2015 GCI
Intro:
My experience with commercial percussion caps has been they often don’t fit tightly on
the nipples, they are expensive, they are usually out-of-stock, they fragment and jam my
revolvers, and they aren’t always reliable. Many folks have used toy gun rollcaps with
varying success but most of their fabrication techniques are haphazard, slow, and crude at
best. My goal was to combine the best techniques and fabricate caps better than what is
currently available. My caps are ‘corrosive’ but for anybody shooting blackpowder who
doesn’t clean their guns the corrosiveness of rollcaps is the least of their worries.
The tools:
My capmaker cup forming tool is similar in design to my gas check maker at

http://castboolits.gunloads.com/showthread.php?200965-Easy-to-build-gas-checkmaker
I’ve found that mild steel (#1018 CRS) rod is a perfectly adequate material for punching
and forming aluminum. The few parts that need polishing are easily done with emery
paper and hardening the steel isn’t necessary for home production rates. The forming pin
is held in the die by a 6-32 flat head screw.
I used two countersinks to make the cone in the end of the punch. The angles aren’t critical. What is needed
is a sloping, smoothly tapered, and polished surface to gently form the cup. The OD of the disk punch
should be sharp. I formed the 12 teeth with a triangle file by screwing the completed, polished punch into
the top of a press to hold it firmly. Then a piece of masking tape was wrapped around the punch to indicate
location and tooth depth and the punch end was filed straight across to form the 12 teeth. The Tap-O-Cap
system ( http://www.thefirearmsforum.com/threads/tap-o-cap-drawings.82768/ ) uses more elaborate teeth
but mine seem to work fine.
To punch out 0.170” diameter rollcap discs I modified a cheap 1/16 “ diameter hand
paper punch by sawing off the punch pin at the punch base. Then clamping the punch
closed and used an 11/64” ( 0.1719) drill to enlarge the die hole and drill a counterbore
into the punch base. Make a 0.170” diameter pin and solder it into the punch base. My
punch was part of set from WalMart and cost only a few dollars. Hardening the steel
parts is not needed. The rollcaps are also from WalMart under the “Legends” brand
containing 0.023 grains of presumably Armstrong’s mixture (potassium chlorate + red
phosphorus). A tweezers make handling the punched rollcap disks much easier.
Drill a 5/32” thick hardwood paint-stirring stick with a #6 (0.204") drillsize to hold
formed cups. I use a spring clamp to hold the stick to the table. Keeping the cups fixed
greatly simplifies filling, tamping, and capping the cups. Because you must concentrate
and keep a steady hand when making percussion caps I do batches of 15 at a time and
then take a break. I can load the stick with cups, fill, cap, and overspray in about seven
minutes for a batch of 15.
Make powder scoop from fired Small Pistol Primer soldered to a 14awg copper wire
shaft. Form a ¼” diameter loop on one end as a handle. File down the SPP cup to
approximately 0.146” ID x 0.075” deep. Mine holds about 0.3 grains weight of Goex
FFFFg.
Make a tamper pin from a 16d nail. Square off and polish end to 0.152” diameter.
Make a storage tray from two CCI-300 Large Pistol Primer trays. Use 22LR cases in the
corners to index the tray halves. Note that the covering tray has the holes facing outward.
Preparing cup material from aluminum soda cans

1) Wearing leather gloves and using a sharp paring knife stab the can shoulder and slice
off the top of can at the shoulder.
2) Using a kitchen scissors cut down the side of the can along the straight line where the
label paint overlaps.
3) Use the scissors to cut off the bottom of the can at the shoulder.
4) Use a guillotine paper cutter to trim off the ragged edges where the top and bottom
were cut off. Trim the sheet to 3 3/8" wide.
5) Now use the paper cutter to cut the 3 3/8" wide sheet into three 1 1/8" wide strips. A
tuna fish can makes a perfect storage container for the strips.
6) Take two strips and place the painted side together and secure the ends with a small
piece of tape. The opposing curl of the strips yields a nice flat uniform piece that works
great for punching.
7) A very light spray of wax furniture polish on the assembled strip lubes it so it punches
cleanly and doesn't smear aluminum in the punch and die. Yield is about 30 cups per
strip.
Forming the cups

I mount the punch and die in a $25 Lee “Reloader Press” since with properly designed
tools very little force is needed. With the ram up, the punch is screwed into the press until
it seats fully (bottoms out) in the die. An old pill bottle (slightly less than 7/8” inside
diameter) is screwed onto the top of the punches 7/8-14 thread to catch the formed cups. I
can make several hundred cups without having to empty the bottle. When punching make
sure the ram is completely stroked so the punch and die bottom out. If not fully bottomed
out the cup isn't stripped off the forming pin and the next cup will jam into it.
Procedure:
1) The prepared double-layer aluminum strip is inserted into the slot in the die. Make
sure the strip is completely inserted and touches the backside of the slot. You should
have a nice round hole punched out of the strip.
2) Ram moves up and simultaneously punches out a disk while the punch teeth crinkle it
so it folds up smoothly.
3) Ram continues up and the disk is folded and shaped to size by the polished tapered
cone and forming hole in the punch while the forming pin in the die forms the inside
surface.
4) At top of ram stroke the formed cup skirt slides past the larger diameter relief hole in
the punch and springs out to catch.
5) As the ram is retracted the skirt is caught in the punch and the cup is stripped off the
die forming pin.
6) After punching a few dozen cups I've noticed aluminum chips build up in the die so I
remove it and clean it out.
This setup works quite well as long as you make sure to fully upstroke the ram. If
you don't the next cup will be jammed into the previous one. If the press ram or die
seating isn’t tight the punch won’t easy slide into the top of the die. In that case only
move the ram down enough so the punch clears the die slot so you can position the strip
for the next stroke i.e. a full upstroke and a partial downstroke of the ram.
Loading percussion caps
1) Insert cups into the stick and solidly clamp to table.
2) Fill cups with 1 scoop, about 1/4 grain, GOEX FFFFg. Use left index finger to steady
scoop by sliding the scoop shaft under the fingernail. Notice how little powder is
spilled using clamped down cups and steadying the scoop. A future project is to make
two indexed plates, one will hold the cups while the other will have funnel shaped
holes to make it easier to pour in the powder charge.
3) Compress the FFFFg powder into the cup with the tamper pin.
4) Place a rollcap disk brown side up over each cup using a tweezers. Because the cups
are 0.157” ID and the rollcap disks are 0.170” diameter the disks can be pressed into the
cups to hold and seal the powder charge in place.
5) Press rollcaps down into the cups using the tamper pin. It works best to line up the
disk over the cup and squarely press it straight down. Occasionally a disk will catch on
the edge of the cup and go in crooked. The result is a bit of the powder pops up on top of
the rollcap. As long as its just a small amount as seen in the photo it doesn’t seem to
affect the cap performance.
6) Glue everything together using a light spray of hairspray from about 12" distance. The
stick should appear damp/wet but not puddled with spray. Don’t saturate the rollcaps. I
use a couple of quick sprays. I use the cheapest aerosol canned hairspray I could find
“Rave 4x Mega” its got flammable solvents, ether, alcohols, vinyl, acrylics, urethane, etc
for a good thin plastic overcoat. The ‘greenie’ pump sprays are mostly water and pond
scum and probably are hygroscopic so I avoid them.
7) Blot off excess hairspray with a paper towel
8) Dry 5 minutes and then push out caps from backside of stick using tamper pin.
9) Dry overnight before using caps.
Testing caps
I tested the hairsprayed caps and they all fired (20 of 20) with no failures. My drop tests
with a 2 ounce steel cylinder showed a sensitivity of 16” compared to a Remington #11
cap sensitivity of 22”. More testing information can be found at:
http://castboolits.gunloads.com/showthread.php?249374-Homemade-percussion-cap-tests
Conclusion
My homemade percussion caps have worked so well for me that I no longer use
commercial caps. I’ve successfully used my caps in revolvers, Kentucky pistols, a
pepperbox, and muskets. Double layer soda can cups hold together better than Remington
caps. A single rollcap doesn’t clog the nipples with paper debris like multiple rollcaps
can. A small amount of 4Fg powder provides enough sparks to reliably ignite the main
charge. The hairspray overcoat provides enough glue that the caps can be transported
without damage. The tooling needed to easily produce reliable caps is inexpensive and
easy to make. I hope you’ll have as much success as I’ve had with homemade percussion
caps.

Guide To Making Percussion Caps2

Uploaded by

Copyright:

Available Formats

Guide To Making Percussion Caps2

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Guide To Making Percussion Caps2

Uploaded by

Copyright:

Available Formats

Guide to making blackpowder percussion caps

My capmaker cup forming tool is similar in design to my gas check maker at

Preparing cup material from aluminum soda cans

Forming the cups

7) Blot off excess hairspray with a paper towel

9) Dry overnight before using caps.

You might also like