MT1136A

SERVICE MANUAL
COLOR TELEVISION RECEIVER

ORIGINAL
MFR’S VERSION A

Design and specifications are subject to change without notice.

 SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK
make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode-
resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Earphone jack
deal with it.

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1
 CONTENTS

SERVICING NOTICES ON CHECKING ................................................................................................... A1-1

HOW TO ORDER PARTS ........................................................................................................................ A1-1
IMPORTANT ............................................................................................................................................ A1-1
CONTENTS .............................................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................................. A3-1~A3-4
DISASSEMBLY INSTRUCTIONS ............................................................................................................. B-1
SERVICE MODE LIST ............................................................................................................................. C-1
CONFIRMATION OF USING HOURS ...................................................................................................... C-1
NOTE FOR THE REPLACING OF MEMORY IC ..................................................................................... C-1
ELECTRICAL ADJUSTMENTS ................................................................................................................ D1-1~D2-1
MAJOR COMPONENTS LOCATION GUIDE .......................................................................................... D3-1
BLOCK DIAGRAM ................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT ...................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/TUNER .............................................................................................................................. G-1, G-2
CHROMA ........................................................................................................................................ G-3, G-4
DEFLECTION/CRT ........................................................................................................................ G-5, G-6
POWER/SOUND AMP .................................................................................................................... G-7, G-8
WAVEFORMS .......................................................................................................................................... H-1, H-2
MECHANICAL EXPLODED VIEW ........................................................................................................... I-1
MECHANICAL REPLACEMENT PARTS LIST ........................................................................................ J1-1
ELECTRICAL REPLACEMENT PARTS LIST ......................................................................................... J2-1, J2-2

A2-1
 G E N E R A L S P E C IF I C A T I O N S
G-1.Outline of the Product
13 inch(335.4mmV):Measured diagonally
Color CRT 90 degree deflection
G-2.Broadcasting System
US System M
G-3.Color System NTSC PAL SECAM or Monochrome signal
G-4.NTSC Playback(PAL 60Hz) Yes No
G-5.NTSC 3.58+4.43/PAL60Hz Yes No
G-6.Antenna Input Impedance
VHF/UHF 75 ohm unbalanced
G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System
2Tuner System
channel Tuner Oscar(W/O HYPER) Oscar(W/ HYPER)
France CATV) Others
Receiving channel
VHF (LOW) 2 ch~ 6 ch
(HIGH) 7 ch~ 13 ch
(CATV) A5 ch~ I ch J ch~ W+29 ch GGG ch~ W+84 ch
UHF 14 ch~ 69 ch
Tuning System
Frequency syn. Voltage syn. Others
G-8.Preset Channel
-- channels
G-9.Intermediate Frequency
Picture(fP) 45.75 MHz MHz MHz
Sound (fS) 41.25 MHz MHz MHz
fP-fS 4.50 MHz MHz MHz
G-10.Stereo/Dual TV Sound
Yes( NICAM GERMAN USA JAPAN) No
G-11.Tuner Sound Muting Yes No
G-12.P ower Source 120 V AC 50Hz AC 60Hz
G-13.P ower Consumption: 65 W at AC 120 V 60 Hz
-- W at DC --- V
Stand by: 6 W at AC 120 V 60 Hz
Per Year: -- kWh / Year
G-14.Dimensions(Approx.) : 362 mm(W) 361 mm(D) 320.5 mm(H)
G-15.Weight(Approx.) Net : 9.5 kg ( 20.9 lbs)
Gross: 11.0 kg ( 24.4 lbs)
G-16.Cabinet Material
Cabinet Front: PS 94HB DECABROM
ABS 94V2 NON-DECA
94V0
Back Panel: PS 94HB DECABROM
ABS 94V2 NON-DECA
94V0
G-17.Protector: Power Fuse

A 3- 1
 G E N E R A L S P E C IF I C A T I O N S
G-18.Regulation
S afety
UL CSA SAA SI CE SEV
BS NF NEMKO FEMKO DEMKO IEC65
SEMKO NZ HOMOLO SABS CNS SISIR
NOM AS3159 DENTORI UNE GOST NONE
Radiation
FCC DOC FTZ PTT CE SEV
SABA SI NF NZ HOMOLO UNE
CNS CISPR13 DENTORI AS/NZS NONE
X-Radiation
PTB DHHS HWC DENTORI NONE
G-19.Temperature
Operation 5 ºC~ 40 ºC
Storage -20 ºC~ 60 ºC
G-20.Operating Humidity Less than 80 %RH
G-21.Clock and Timer
Sleep Timer Yes Max 120 Min.( 10 Min. Step) No
On/Off Timer Yes Programs No
Wake Up Timer Yes Programs No
G-22.Timer back up Time :More than -- Minutes (at Power Off Mode)
G-23.Terminals
VHF/UHF Antenna Din Type F-Type France Type
Video Input(Front) Phono Jack (RCA ø8.3) BNC
Video Input(Rear) Phono Jack (RCA ø8.3) BNC
Video Output(Rear) Phono Jack (RCA ø8.3) BNC
Audio Input(Front) Phono Jack (RCA ø8.3)
Audio Input(Rear) Phono Jack (RCA ø8.3)
Audio Output(Rear) Phono Jack (RCA ø8.3)
21 Pin DC Jack(Center + ) Ear Phone Jack(ø3.5)
Head Phone Jack(ø3.5) AC Outlet Ext Speaker
Diversity S Input(Front) S Input(Rear)
G-24.Indicator : Power Stand By On Timer NONE
( ) ( ) ( )
G-25.Display
On Screen Display
Menu Clock Set( 12H 24H) System Selec On/Off Timer
Hotel Lock Area Code CH Tuning
Sound 1/2 NICAM Auto Off Picture
Guide CH Set Audio Language
CATV Pin Code Registration Pin Code Registration
V-Chip
Control Level Sound Brightness Contrast
Color Tint(NTSC Only) Sharpness
Tuning Bass Treble
Balance Back Light
Stereo,Audio Output,Bilingual Picture Menu
Stereo,Audio Output,SAP Mid Night Theater
Stereo,Audio Output GAME
CH/AV Clock Pin Code Hotel Lock
Sleep Timer Sound Mute Channel
G-26.OSD Language
Eng Ger Fre Spa Ita Por Jpn
OSD Language Setting
Eng Ger Fre Spa Ita Por Jpn
Not Applicable

A 3- 2
 G E N E R A L S P E C IF I C A T I O N S
G-27.Speaker
3 inches Imp. 8 ohm x 1 pcs
Max 1.0 W (Typical)
10% 0.8 W (Typical)
G-28.EXT Speaker
Yes -- W Imp -- ohm
G-29.Carton
Master Carton: Need No Need
Content: ---- Set
Material: ---- / ---- Corrugated Carton
Dimensions: ---- mm(W) ---- mm(D) ---- mm(H)
Description of Origin Yes No
Gift Box
Material AB Double/Brown Corrugated Carton ( with Photo Label)
AB Double/White Corrugated Carton ( with Photo Label)
AB Double Full Color Carton W/Photo
Dimensions: 408 mm(W) 440 mm(D) 380 mm(H)
Design: As Per BUYER 's
Description of Origin: Yes No
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height 25cm 31cm 46cm 62cm 80cm
Container Stuffing: 866 Sets / 40' container
G-30.Accessories
Owner's Manual ( W/Guarantee Card) [English/French]
Channel Film
AC Plug Adapter Remote Control Unit
Battery (UM- 4 x 2 )
S afety Tip Toll Free Insert Sheet
Guarantee Card Audio-Video Cord (RCA)
Registration Card Warning Sheet
Quick Set-Up Sheet Schematic Diagram
Information Sheet U/V Mixer
75 ohm Coaxial Cable ( Single Shield Double Shield)
300 ohm to 75 ohm VHF Antenna Adaptor
21pin Cable Car Cord
Rod Antenna
One Pole Two Pole ( F-Type Din Type France Type)
Loop Antenna ( F-Type Din Type France Type)
G-31.Other Features
Auto Degauss Auto Search Full OSD
Auto Shut Off CH Allocation Premiere
Canal+ SAP Comb Filter
CATV Channel Lock Auto CH Memory
Anti-Theft Just Clock Function Hotel Lock
Rental Game Position Fastext
Unitext TopText Closed Caption
Picture Menu Mid Night Theater V-Chip
G-32.Switch
Front
Power(Tact) Channel Up Volume Up
System Select Channel Down Volume Down
Main Power S W Sub Power
Rear
AC/DC TV/CATV Selector
Degauss Main Power S W

A 3- 3
 G E N E R A L S P E C IF I C A T I O N S
G-33.Magnetic Field
BV : +0.45G BV : +0.35G BV : +0.25G
BH : 0.18G BH : 0.30G BH : 0.30G
BV : -0.15G BV : -0.25G BV : -0.50G
BH : 0.15G BH : 0.15G BH : 0.30G
G-34.Remote Control Unit: RC-74
Power Source: D.C 3 V Battery UM - 4 x 2
Power Quick View TV/AV
Stand By Status Bar Select
0 Time Select PAL/SECAM
1 Time Set Volume Up
2 Mute Volume Down
3 CH Skip CH Call
4 CH1/CH2 CH Down
5 Channel CH Up
6 Text/Mix/TV CH Down/Page Down
7 Display Cancel CH Up/Page Up
8 Initial P age +/-
9 Store Program
10 Reveal F/T/B
11 Sleep Hold
12 Aft/Skip List
1 Preset Rotate
2 5.5/6.5MHz Browse
0/10 Auto Memory Std/Auto
Tone 1/2 Auto Memory
Info Call Band Select
Mono/Auto Reset Search
TV/Caption/Text Menu Clock/Program
Expand Enter Clock/Set
Red Add Ch Set
Cyan Delete Set +
Normal Yellow Set -
Color System Random Green
Wide Selecy Tuning Up/Time Text Nicam/Mono
Auto Wide On/Off Tuning Down/Reset Tone A/B
Picture Position Navi FM Transmitter
Direct Change/Auto Search Back Light
Picture Menu Mid Night Theater

A 3- 4
 DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

GND on the CRT

Fig. 1-3

NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip

GND on the CRT

Fig. 1-1

2. Flip up the sides of the Rubber Cap in the direction of the Fig. 1-4
arrow and remove one side of the support.
(Refer to Fig. 1-2.) 4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
Rubber Cap

CRT
Support Support
Fig. 1-2
CRT
Fig. 1-5

5. Confirm that the Support is securely connected.

6. Put on the Rubber Cap without moving any parts.

B-1
 SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 2 seconds.

Set Key Remocon Key Operations

VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.
VOL. (-) MIN 1
NOTE: Do not use this for the normal servicing.

POWER ON total hours is displayed on the screen.

Refer to the "CONFIRMATION OF USING HOURS".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".

Writing of EEPROM initial data.

VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.

Display of the Adjustment MENU on the screen.

VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF USING HOURS

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
ADDRESS DATA
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel INIT 00 83 Initial setting content of MEMORY IC.
button (6) on the remote control for more than 2 seconds.
3. After the confirmation of using hours, turn off the power. CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1 + (ones digit value)

NOTE FOR THE REPLACING OF MEMORY IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need the setting for after INI 09.

INI INI INI INI INI INI INI INI INI IN

ADDRESS
00 01 02 03 04 05 06 07 08 09
DATA 88 6C 00 00 00 00 00 98 05 0E

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
3. ADDRESS and DATA should appear as FIG 1.
4. ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
5. Press ENTER to select DATA. When DATA is selected, it will "blink".
6. Again, step through the DATA using SET + or - until required DATA value has been selected.
7. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
8. Repeat steps 4 to 7 until all data has been checked.
9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.

C-1
 ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL
1. RF AGC DELAY
ADJUSTMENTS 2. VIDEO LEVEL
Read and perform these adjustments when repairing the 3. FM LEVEL
circuits or replacing electrical parts or PCB assemblies. 4. OSD H
CAUTION 5. CUT OFF
6. X-RAY
* Use an isolation transformer when performing any 7.
service on this chassis. 8. 0. RETURN
* Before removing the anode cap, discharge electricity Fig. 2-2
because it contains high voltage.
* When removing a PCB or related component, after 2-2: CUT OFF
unfastening or changing a wire, be sure to put the wire
back in its original position. 1. Using the remote control, set the brightness and
Inferior silicon grease can damage IC's and transistors. contrast to normal position.
* When replacing IC's and transistors, use only specified 2. Activate the adjustment mode display of Fig. 2-1 and
silicon grease (YG6260M). press the channel button (5) on the remote control.
Remove all old silicon before applying new silicon. The Fig. 2-2 appears on the display.
3. Press the channel button (5) on the remote control.
1-1:Prepare the following measurement tools for 4. Adjust the Screen Volume until a dim raster is obtained.
electrical adjustments.
1. Synchro Scope 2-3: WHITE BALANCE
2. Digital Voltmeter NOTE:
Adjust after performing adjustments in section 2-2.
2. BASIC ADJUSTMENTS
1. Receive the color bar pattern.
On-Screen Display Adjustment
2. Activate the adjustment mode display of Fig. 2-1 and
In the condition of NO indication on the screen. press the channel button (2) on the remote control.
Press both VOL. DOWN button on the set and the channel The Fig. 2-3 appears on the display.
button (9) on the remote control more than 2 seconds 3. Adjust the adjustment mode display of Fig. 2-3 until
to appear the adjustment mode on the screen as shown the white color is looked like a white.
in Fig. 2-1.
NOTE 1. AKB AUTO
Use the channel buttons (1-8) on the remote control to 2. R. BIAS
select the options shown in Fig. 2-1. 3. G. BIAS
Press the channel button (0) on the remote control to 4. B. BIAS
end the adjustments. 5. R. DRIVE
6. G. DRIVE
7. B. DRIVE
1. H/V 8. AGC AUTO 0. RETURN
2. AKB Fig. 2-3
3. COLOR TEMP
4. PICTURE 2-4: SUB BRIGHTNESS
5. OTHERS
6. TEST PATTERN 1. Receive the monoscope pattern.
7. 2. Using the remote control, set the brightness and
8. (VOL TEST) 0. END contrast to normal position.
Fig. 2-1 3. Activate the adjustment mode display of Fig. 2-1 and
press the channel button (4) on the remote control.
2-1: RF AGC DELAY The Fig. 2-4 appears on the display.
4. Press the channel button (1) on the remote control.
1. Receive an 80dB monoscope pattern. 5. Press the VOL. UP/DOWN button on the remote control
2. Connect the digital voltmeter between the pin 2 of until the white 10% is starting to be visible.
CP101 and the pin 6 (GND) of CP101.
3. Activate the adjustment mode display of Fig. 2-1 and
press the channel button (5) on the remote control. 1. BRIGHT
The Fig. 2-2 appears on the display. 2. CONTRAST
4. Press the channel button (1) on the remote control. 3. COLOR
5. Press the VOL. UP/DOWN button on the remote control 4. TINT
until the digital voltmeter is 2.0 ± 0.05V. 5. SHARPNESS
6. OSD CONT
7.
8. 0. RETURN
Fig. 2-4

D1-1
 ELECTRICAL ADJUSTMENTS
2-5: SUB TINT/SUB COLOR
1. Receive the color bar pattern. 1. H. PHASE
2. Connect the synchro scope to TP023. 2. H. BLK
3. Activate the adjustment mode display of Fig. 2-1 and 3. V. SIZE
press the channel button (4) on the remote control. 4. V. POSI
The Fig. 2-4 appears on the display. 5. V. LIN
4. Press the channel button (4) on the remote control. 6. V. SC
5. Press the VOL. UP/DOWN button on the remote control 7. V. COMP
until the waveform becomes as shown in Fig. 2-5. 8. (H FREQ) 0. RETURN
Fig. 2-7
6. Activate the adjustment mode display of Fig. 2-4 and
press the channel button (3) on the remote control.
7. Adjust the LEVEL "A" section of Blue to the LEVEL "D" 2-8: VERTICAL SIZE
section of White by pressing the VOL. UP/DOWN button 1. Receive the crosshatch pattern.
on the remote control. (Refer to Fig. 2-6) 2. Using the remote control, set the brightness and
8. If the LEVEL "A" section through "C" section are not the contrast to normal position.
same compared with "D" section, adjust the LEVEL again. 3. Activate the adjustment mode display of Fig. 2-1 and
press the channel button (1) on the remote control.
The Fig. 2-7 appears on the display.
4. Press the channel button (3) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the center of crosshatch is square.

2-9: VERTICAL LINEA

1. Receive the color bar pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
Fig. 2-5 3. Activate the adjustment mode display of Fig. 2-1 and
press the channel button (1) on the remote control.
The Fig. 2-7 appears on the display.
4. Press the channel button (5) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the VERTICAL LINEA is 14 step.

2-10: HORIZONTAL PHASE

1. Receive the color bar pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 2-1 and
press the channel button (1) on the remote control.
"D" "C" "B" "A" Fig. 2-6 The Fig. 2-7 appears on the display.
4. Press the channel button (1) on the remote control.
2-6: FOCUS 5. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right
1. Receive an 70dB monoscope pattern. and left becomes minimum.
2. Adjust the Focus Volume until picture is distinct.
2-11: OSD HORIZONTAL
2-7: VERTICAL POSITION
1. Using the remote control, set the brightness and
1. Receive the color bar pattern. contrast to normal position.
2. Using the remote control, set the brightness and 2. Activate the adjustment mode display of Fig. 2-1 and
contrast to normal position. press the channel button (5) on the remote control.
3. Activate the adjustment mode display of Fig. 2-1 and The Fig. 2-2 appears on the display.
press the channel button (1) on the remote control. 3. Press the channel button (4) on the remote control.
The Fig. 2-7 appears on the display. 4. Press the VOL. UP/DOWN button on the remote control
4. Press the channel button (4) on the remote control. until the difference of A and B becomes minimum.
5. Press the VOL. UP/DOWN button on the remote control (Refer to Fig. 2-8)
until the horizontal line of the color bar comes to
approximate center of the CRT.
Perform the adjustment of step 5 to step 12.

D1-2
 ELECTRICAL ADJUSTMENTS

[ TV ]

OSD H

A B
Fig. 2-8

2-12: VCO FREERUN

1. Place the set with Aging Test for more than 10 minutes.
2. Receive the UHF.
3. Disconnect the Antenna while receiving the UHF and
set to the Noise screen.
4. Once turn off the Power and turn on the Power again.
5. Approxi. 3 seconds later, input the Antenna again.
6. Connect the digital voltmeter to TP201.
7. Adjust the L205 until the digital voltmeter is 3.1 ± 0.05V.

D1-3
 ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch pattern
terrestrial magnetism. on the center of the screen by adjusting the pair of
3. Turn ON the unit and demagnetize with a Degauss Coil. 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted 3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar
generator. 1. Adjust the differences around the screen by moving
3. Slide the deflection yoke until it touches the funnel the deflection yoke upward/downward and right/left.
side of the CRT. (Refer to Fig. 3-2-a)
4. Adjust center of screen to green, with red and blue on the 2. Insert three wedges between the deflection yoke and
sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern RGB RGB
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the R
pair of 6 pole magnets. G
8. Adjust the crosshatch pattern to change to white B
R
by repeating steps 6 and 7. G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Adjust after performing adjustments in section 3-1. Fig. 3-2-a

1. Receive the green raster pattern from color bar

generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw. WEDGE

DEFLECTION YOKE
WEDGE POSITION
DEFLECTION YOKE SCREW
MAGNET SCREW Fig. 3-2-b

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D2-1
 MAJOR COMPONENTS LOCATION GUIDE

J351

L205

TP201
TU001

FB401

CP101

FOCUS VOLUME
SCREEN VOLUME
MAIN

TP023
J801

CRT

D3-1
 BLOCK DIAGRAM

EARPHONE JACK

2
CH. UP
TU001 V. SIZE/VIDEO/CHROMA/SYNC 3
IC201 LA76814M-MPB
CH. DOWN IF AGC 1
IC351 AN7511
11 1 T351
AUDIO DC SOUND SOUND
73 2 6
VOL. UP SW VOL AMP TRANS
SP351
IF/RF AGC FM LIM
77 AMF 69
VOL. DOWN DRIVE DET
CF201
67 Q604, Q605
SAW FILTER 78 VIDEO VIDEO VIDEO
POWER MICON VIF 56
IC101 OEC3039B 79 AMP DET AMP BUFFER
Q801
34 MUTE P00 RED R 19 12 17 RED OUT
GREEN G 20 13 SW RGB OUT 18 Q802
10 KEY1
OS101 BLUE B 21 14 19 GREEN OUT
5V REG.
1 32 REMOCON IC103 KIA78L05BP-AT Q803
VER C/D 26
2 37 MUTE BLUE OUT
SD 31 1 Q602
3
V. SYNC 16 BUFFER 9V REG.
Q104 VIDEO IN 15 49 SEP. IC601 KIA78L09BP-AT
POWER SW 40 POWER ON
XT1 5 VIDEO 1st 2nd H 30
SW AFC AFC OUT 1
X101
RESET 32.768KHz 54 2
IC104 PST600C XT2 6 Q402
Q101 H. SYNC
SEP. 47 H. DRIVE
3 13 RESET
V. SYNC 17 V-BUFFER
Q401
Q103 Q102 X601
3.579545MHz H. OUT
X-RAY SW 3 X-RAY H. SYNC 18 H-BUFFER V-OUT
IC401 LA7840

IC501 PUMP UP 3 9 7
STR30110
- B G R
POWER REG. AMP CRT
+ Heater
5 3 DEGAUSS COIL
4 F 8
D501-D504 7 5 4 2
RECTIFIER

L501 IC402
5 2 KIA7805PI
5V REG. DY
3 1
1 3

+B FB401
F501 +5V 10
1 F
FBT
S
9 HV

AC IN

E-1 E-2
 PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE

J351
R501

CP502_1
W831
CP501
R502
Q401 C503 W847

C502
W846
F501
HEATER COL

FH502

FH501

W845
TH501

OS101
FB401
C443 L501
AFC W017
4A 124V

C504
CP802B
B+

R427

D501

D502
GND C442

C805

C806
R815

R811

R814
R816
C506_1

D503
D504
W897
W891
CP803B

C801

C804

R809
ABL
CD802B
R446 C440
180V 25V

W020
Q802
CD803B Q801

SW105
8V 12V C439 R813 Q803
T401 Q402_1 CP801_1
W019 C437

RY101
R806

R503

C446_1

R362
R802
D407
D404
D422
D408

C435_1

R428
W043
TP024

W026

R515
R804
W827

L406
R147
D410

C420

W822
29

D124
R4

SW104
05

IC501
R8

R448
W801

C416
C405

R509

R449
C507_1
D125 C132 01 TP023

R177
J8
C433

D411 C819 7

R405
R401
R80

CP401

R508
W025
C412 TP022
C

C
D

D
80

C404
80

W857
2A

R410
3A

SW103
C

C434

W014
C430

C133
P8

D126
W035
C

03

3
P8

R80
A
02

R507_1
R409
TP501
A

T351
W837
C448

W024
CP351_1
W031
W023

R443
W029

R447
C519 R408

D402

D401
W833
W030

D403

R611

SW102
W830

W816
R414_1
W022

W802
R363

W021
W842

D127
C415

C351
W853
W032

IC351 C354
C414

W821
W851 R356
IC402 C357

SW101
IC401 HS401 C418 C135

R161
W044

C131 R162

W005
W018

W006
C628
W836

IC103
R506_1

W829
C627_1
C422

R418
R433

W811

W007
R416

C425

R417

W810

R6
R432

C427

D605
15 R110

W828
C625
_1
W039

W042

R114
W038

R117
R649 Q101
C429

C417_1 IC104
R445
R421

C605

R605 W817
R660

C624

X601

W015
R407

R001
L601 C648

C623 D101
TP201

CC001

C111
Q102

W046

R609 C617
C646 C615
C209
C208

R002
W819

C120
C611
D609
CP101_2

R607
D602

C121

C102
L205

Q604 C649

C618

R614
C653
W823

Q605 C107

R133
W001
C001

C620
C622

W016

C643
C619
D001

C352
C652

C211 C217

C608_1

W013

W004

W003
R143
C426 D610

X101
C644

C614

C616
C123

D606
C212

C651

C215
C002

C609

C103
C202 C637

W813
Q103
C635
C204

IC601 Q602 Q104

C214

D103

R120

W010

W009
C213

W008
C004 IC199

C134 R132
W041
C626

C201

W011
R625
R626

R643
R627

R604
R006
R007

C650

AGC CF201_1
C636

W002
R130

R145

R136
R141
C101
R601
R602
R648

D603 L201 C203 C105

L202
TU001

F-1 F-2
F-3
R139
R134

R101 R104 R103 R102 R112

R113

R115 R107
C110 R138
R353

R357 C109
R109 R137
1

C108
R111 IC
13
37

10
1 R128
R351 R119 R127
R118 R142
R354
R144
25

R146
R116
C129
R121
R123 R122 C130 R105
R150 R149 R106
R148

R612 R645
R613 R606

R608 R637
R653
R638

R636
R632
C612
C632 R124
R646
R647
25

41

IC
20
1 R209
1

R202 R201
C645
C224
R206
64
SOLDER SIDE

C610 R618

R208
C216 C218 R215
R406
R622 R203 C206 C207
PRINTED CIRCUIT BOARDS

R663 R662 C210 R205

MAIN (CHIP MOUNTED PARTS)

C647 R656 R204

R624R623 R655 R210 R211

R404 R619 R651

R666 R620 R652

C654
R665
R664
R419
R420

R213
R431 R212

R402

R403
F-4
 A B C D E F G H

MICON/TUNER SCHEMATIC DIAGRAM

ACCESSORY
8 8

ANT001
HPAS-2S780 ATC001 TU001 ENV56D67G3
NXC0032-010010

3 ADRES

1 AGC
5 SDA
7 BPL

4 SCL
9 BTL
15

13
6 V.S
11 IF

10

2
8
TM101

14

12
R25-1028

NC

NC

NC
NC

NC
0

8.8
30.0

4.8

4.8

1.5

6.9

2.0
5.0

6.3V 100 YK
68K 1/2W

68K 1/2W
0.022 M
HZ30-3L
C004

7 50V 2.2 KA 7

C001
D001

R001

R002

C002
W828

OS101 W813
PIC-28143SY-2

W823
1 Vout

3 GND
2 B+
W810

W811

16V 10 KA
C123
R133
6 6
47 1/4W

R136 R143
6.7 12K 1.5K
CC001 R134 0 X-RAY SW
Q103
1K 2SC1815Y
0

5V REG.
IC103 KIA78L05BP-AT
5 5

R006

R007

270
270
SKHVBED010

SKHVBED010

SKHVBED010

SKHVBED010

R132 10K

R130 10K

R127 47K
SKHVBED010
CH DOWN

VOL DOWN

R141
R145
POWER

10K
SW101

SW102

SW103

SW104

SW105

1K
CH UP

VOL UP

0.8
C103 C134 R137
POWER SW
0.1 TF 50V 1 KA 4.7K 0 Q104 OUT GND IN
R102 R103 R104 R101 2SC2001_L
0

R138
1 2 3

68K
5.6K 1.8K 1K 560 MICON
5.0 0 12.5
IC101 FROM/TO POWER/SOUND AMP
OEC3039B 0 0NC 0NC 0NC 0NC 5.0 0 0NC 4.6 0 NC 0 0 C135
48 47 46 45 44 43 42 41 40 39 38 37 AT+12V
0.022 M
R107 0 +B

36
AV2 P02 NC
1

P15/PWM3 X-RAY_TEST
4.7K 0
0
13. RESET RES POWER

35
NC AV1 P01 NC
2

P16 PAL/NTSC
4 D103 14. FILTER FILT 0
R139
GND 4
0
15. VIDEO IN CVIN

34
P17/PWM X-RAY MUTE P00 AUDIO_MUTE
3

17. V.SYNC VS 0 10K

MTZJ5.6B R128
0
18. H.SYNC HS

33
NC
4

VSS FROM DEFLECTION/CRT

C105 C109 19. RED R 0 10K
1.2

R142
P73/INT3/TOIN

10K
20. GREEN G

32
XT1 +5V
5

6.3V 1000 YK 15P CH 1 REMOCON 5.0

21. BLUE B
C110 R115 2.1 V_SYNC
22. BLANK BL P72/INT2/TOIN

31
XT2
6

5.0 H_SYNC
18P CH X101 390K 23. I SD
32.768KHz 5.0
37. MUTE

30
VDD P71/INT1 NC
7

FROM/TO CHROMA
38. B.B.H 0
0
39. AKB AGC

29
NC P70/INT0 NC
8

40. P06 POWER OUT 0

120P SL
120P SL
2.4 IF
41. P07 I2C BUS OFF

28
P84/AN4 ATF P63/SCLK1 NC

C129

C130
9

43. P10/SD0 0 I2C_OFF

3 5.0 3
44. P11/SI0
10

27
RESET P85/AN5 KEY1 P62/SDA1 NC
R112 45. P12/SCK0 0
IC104 PST600C R113 R105
2.2K 5.0 I2C_SCL
46. P13/PWM1
11

P86/AN6 KEY2 I2C SCLP61/SCLK0 26

2.2K 47. P14/PWM2 5.0 4.7K I2C_SDA
0
12

25

NC P87/AN7 I2C SDA P60/SDA0 R106 C101 OSD_BLANKING

5.0
0.01 Y
5.0 5.0 0 OSD_BLUE
V.OUT

13 14 15 16 17 18 19 20 21 22 2423 4.7K 5.0

R146

R116

R119
R117

1K

150K
GND

1K

33K
VCC

3 5 6 7 8

M24C01-BN6
5.0 2.8 3.1 0 5.0 4.3 0 0 0 0 0 NC 0

MODE
OSD_GREEN

SDA

VCC
SCL
1 2 3 H-BUFFER
R110

R108

MEMORY
10K

10K

V-BUFFER OSD_RED
Q102
5.0 0 5.0 Q101 2SC1815Y VIDEO
4 4.3
5.0 2SC1815Y
AFT_IN
1SS133

VSS
D101

0 0

IC199
E0
0.022 M

E2

E1
10K

10K

10K
0 0

C131
R148

R149

R150

R144

R118

2.7K
4 3 2 1

2.2K
2
2 0 0 0 0 2
50V 1 KA
R111 330

R161 R162 R120 4.7K

C111

10K 10K R121 4.7K

50V 4.7 KA
C120

R122 4.7K
50V 0.1 KA

R123 4.7K
50V 2.2 KA
0.033 M

R109 1M
C121

C107

C108_1
R114
C102

560P

R124

4.7K
220

PCB010
TM8411

1 1

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-1 G-2
 A B C D E F G H

CHROMA SCHEMATIC DIAGRAM

8 8

R656

12P CH

33P SL
1K

C654

100P
SL
5.0 0 VIDEO

15uH
3.3K
VIDEO BUFFER

1K
0.3 0.3 BUFFER

6.3V 1000 YK
6.3V 100 KA
Q604 Q605
2SA1015Y 5.0 2SA1015Y

L601
R665

R655

C647

C648

0.01 Y
0

100 KA
R664
C652

C643

C623
C622
6.3V

470
8
6

D609 R652

3.579545MHz
0.01 Y
C649

10K
6.3V 47 KA

X601
1SS133 47K

R623

24K
KANP
R619 16V 10

C653
270

50V 3.3 R666

C651
VCO

SL

9
L205

C216

0.01 Y

R622
3602038 R624

1K
KA
7 7

3P

C624

C605
270
R620
R651

50V 0.47 MH7

6 1

100
24K

C627_1
15P CH
2 NC

C645
4 3 R660 R662

10 KA
50V 1 KA

50V 2.2 KA

C625
C215
C628 0.047 M

1M
560 1K

10
C620
TP201
NC C610 100P SL

50V 1 KA

16V
R663
C646

V/C GND

820
R618

11
C218
0 0 0 0 4.1 4.1 2.2 0 0.3 3.3 2.2 5.0 0 0 0 2.6 0 2.7 0.3 3.3 1.7 0 0 0
0.001 Y 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
R208 C217 49 48 47 46 45 44 43 42 41 40 39 38 37 36
3.0 50 35 0

65

40
220 50V 0.47 KA A2C
2.2 CLMP CLMP VC0 CW 0
51 PLL 34

66

39
KIL X-RAY

R612 R606

C615
NC

22 KA
VIDEO

10K
7

16V
6 R203 2.0 52 TRAP AMP 33 0 HOR GND 6
VIDEO

67

38
VIDEO FILTER
APC1 TINT

Y
0.001
C206

C207
SW

1K
47P
C211 1K DET ADJ

SL
R204 2.5 53 32 2.1 R613 D602

68

37
SPLL
1K 50V 1 KA BPF HOR 1K 1SS133
C210 3.0 0
54 VCO 31

69

36
BPF BPF SW
47P SL
0 1/256 FBP CLK30 0
LIM

70

35
ACC SYNC
AMP SEP R607 W817
SW TRAP
0 DEMO HOR AFC2 REF29 1.7

71

34
TO POWER/SOUND AMP C/D
1.1 4.7K +-1% 12
0 DC FM DELAY 28
R605 R611

72

33
VOL DET LINE AFC1 PHASE
5 COLOR SHIFTER 2.7K 1/4W 22K 1/4W
R205

HZ6B2L
2.0 1
CLAMP 0

D605
73

32
AUDIO_OUT
C209

0.01

100 PEAKING HOR

Y

GND 0 CONTRAST RGB 0

5 CORING OUT 5

74

31
BRIGHT MATRIX H_GND
13
C212 0.01 M 2.4 2 27 0.4 R609 FROM POWER/SOUND AMP
BLACK
75

30
STRETCH 100 1/4W C617
R608 R614 R615 R649
C213 0.022 M 0 3
VIF 26 2.7
IF AGC
76

29
DC‘ +B

M
R210

C208

C611
0.01

0.01
47K

RES 3K 50V 1 KA 1.8K 3W 1.8K 3W 1.8K 3W

R213 1.5 5.0
Y

4 25
HOR
77

28
RF AGC VER

0.01 Y
47 YK
C618

C619
10K SAW FILTER SEP VOC

16V
0 5 AFT 24 2.7 C614
IN IN G OUTOUT CF201_1 OSD OSD
78

27
VER VER
1 2 3 4 5 SAF45MFX220ZR FIX GAIN 0.47 TF
R212

5.6K

SW C/D RAMP 14
2.9 6 23 2.3 C616 0.22 TF
79

26
C214 0.01 Y

22 2.3 C612 C637

0 7 BUS ABL CLAMP R643
DRIVE/CUT-OFF
80

25
AKB
R206

2.2K

R215 100P A 50V0.47 KA

16V 10 KS
8 9 10 11 12 13 14 15 16 17 18 19 20 21
51 1/2W

R638

C626
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2.7K
L202
5.6K R632
4 0 0 0 0 0 4.8 2.5 2.4 0 4.6 3.9 0 0 0 0 7.8 2.6 2.6 2.6 0 0 0 0 0 W833 4
1uH

1SS133
C224 2.2K

D606
50V 1 KA
C201
C204

9.0 0 12.0
R211 5P CH V.SIZE/VIDEO/CHROMA/SYNC 1 2 3
0.01

R604 100 1/4W

R625 100 1/4W

R626 100 1/4W

R636

2.7K
IC201

16V 47 YK
B OUT GND IN

1SS133
68

0.01 Y

R653
LA76814M-MPB

D610
C608

560
C609
C202
R209

7.5K

BUFFER 2.0
0
Q602
6.3V 2SA1015Y

KA
16V 10
R637

C644
1K

1K
470 0
1K

R202

68P SL
YK

C632
100K 9V REG.
10uH
L201

R601

R602

R201 IC601 KIA78L09BP-AT

50V 0.47 KA

NP
100K

50V 10 NP
10K

FROM/TO MICON/TUNER C203 C635

C650
C636

50V 10
3 R627 FROM/TO DEFLECTION/CRT 3
0.1 M
VIDEO
56K 1/4W D603
R648

IF ABCL
11E1N
+5V
AGC X_RAY
4.7K

4.7K

4.7K

AFT_IN H_SYNC
I2C_SDA H_OUT
R645

R646

R647

I2C_SCL V_OUT
15

16

17
OSD_RED +12V
OSD_GREEN CLAMP
OSD_BLUE
OSD_BLANKING B.OUT
G.OUT
2 2
I2C_OFF R.OUT
W819

173979-6

I2C_SDA
I2C_SCL

I2C_OFF

B.OUT
GND

AGC

PCB010
CP101_2

TM8411
6
5
4
3
2
1

1 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-3 G-4
 A B C D E F G H

DEFLECTION/CRT SCHEMATIC DIAGRAM

8 FROM/TO CHROMA 8
GND GND
GND 5 5 GND
CLAMP CLAMP
CLAMP CLAMP 4 4 CLAMP
G.OUT G.OUT
G.OUT G.OUT 3 3 G.OUT
B.OUT B.OUT
B.OUT B.OUT 2 2 B.OUT
R.OUT R.OUT
R.OUT R.OUT 1 1 R.OUT
CP802A CD802 CP802B
+5V 51048-0510 2E052503 51048-0510
V-OUT IC401 LA7840

THERMAL PUMP
PROTECTION UP

C804_1 390P B

560P B
C805_1 470P B
7 AMP- 7
+
GND VCC RED OUT GREEN OUT BLUE OUT
1 2 3 4 5 6 7 Q801 Q802 Q803

C806_1
0 12.6 25.8 2.6 2.6 25.3 2.2 2SC1473A 2SC1473A 2SC1473A
3.2 3.2 3.2

35V 100 YK

220

220
100.6 98.4 95.4

220
18
R414

C414
2.7 2.7 2.7
5V REG. 22 D403
3.9K CD801_1 CP801_1

0.0022 B

R809

R811

R814
IC402 KIA7805PI

C429
C415 TBS-X01X-A1
11E1N
23 1 1
500V 22P SL

R431 50V4.7 MHER402

15K

330 1/2W
TF

TF
100V 0.15

100V 0.068

4.7K

4.7K

4.7K
C422

C430
R410
R403
C425

18K
R418
IN GND OUT R420

R813

R815

R816
W836
6 1 2 3 6

25V 1000 YK
R419
10K+-1% 22K

1K
11K +-1%
1.5K
8.0 0 5.0

1 1/2W
R417

C418

R416
MHE
W842

50V 3.3
C417
R433

1.5K 1/2W

6.3V 470 YK

50V 10 MHE
1/2W
V801

1.5K 1/2W
R407

R432
C426

C427
HS401 A34JXV70X28N45

1.5

TP022

TP024

TP023
9
10
TO MICON/TUNER R
R404

18K 1/4W +-1% 3.9K

HZ27-1L 100K 1/4W +-1%

8
R406

1.5K

6 G
B 24 25 26
+5V W837 11
R401

R405

V_SYNC 5 7 1
5 5
10K +-1%

H_SYNC

2.7K 1/4W

2.7K 1/4W

2.7K 1/4W
15K 2W
R408

15K 2W

15K 2W
R802
R803

R805

R807
R804

R806
D401

100V 22 YK
D402 R409
5

C434
HZ11B1L 12K +-1%
4

AU02A
D411
T401 3
19 305Y002
C439 NC 2
3 4
1
500V 22P SL

250V 0.47 ECWF

NC 2 CP401
FROM/TO CHROMA R429
1 6 TV-50P-05-V2
4.7K 1/2W

C437
R446

H.DRIVE 2.7 1W

330P B
V_OUT

C801
Q402_1
X_RAY
2SC2271 FB401
4 ABCL 27.0 3214029F
4
W897
H_OUT 21 130.0 COL
0.3 20 1 HV
1.6KV 0.0047 ECWH

H_SYNC 0 H.OUTPUT
500V 470P B

2KV 220P BP
Q401 130.0 W831 D410
+12V
C440

2SD2599(LBOEC1) AU02A
C442

W821 FOCUS
137.0
100 1/4W

NC VIDEO F
C443

0 C420 6
R427

0
1KV0.001 B 0.6 B+ S
2
L406 GND 0
W891 11
0 AFC
18uH R428 9 SCREEN
C416 HEA ABL 0.3 1

2KV 0.001 B
0 TER 7
10 CP806_1

C819
200V 0.012 PP 6.8 1/2W
0 GND
8
3 0 E12 3
4 GND 0
W827 8
R447 R448 R449 C446 C404 0 96.4
E25 6.4
3 0
E8
5

3
3.9K 2W 3.3K 2W 3.9K 2W 160V 1 YK 10V 470 YK

4
0 0

1
10V 470 YK

D408 D407 AU02A 0

C412

F
AU02A

7
101.6

8
9
FROM/TO POWER/SOUND AMP
R443

35V 470 YK
D422

W857
99.6

C433
SOUND+B C448 R445
4.7 2W AU02A J801
100V 22 YK 220K 1/4W 220K 1/4W
HPS3200-010501
100V 0.22 TF

+B
2 2
C435_1

R421

HEATER HEATER HEATER

4 4
GND GND GND
3 3
GND GND GND
GND 2 2
16V 470 YK

180V 180V 180V

1 1
C405

CP803A CD803 CP803B

D404 2E042302
51052-0400 51052-0400
+12V
AU02A
PCB110
TC8270
PCB010
TM8411

1 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-5 G-6
 A B C D E F G H

POWER/SOUND AMP SCHEMATIC DIAGRAM

8 8

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.
4A 125V ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).

DEGAUSE COIL
7 L502 7
8F140025

POWER REG. 2

2
IC501 STR30110 R502_1
D501 D502 1

1
CP502_1

0.001 B 0.001 B
2.2 5W RM11C RM11C

C503

1KV
TV-50P-02-A1
MS501

C504

1KV
128B000018 TH501_1
D504 D503 PTH451A100BG3R0Q
1 2 3 4 5
0 138.0 180.0 137.0 6.9 RM11C RM11C

10K 1/2W
330K 1/4W
TP501

R503

R508
6 C502 6

12K +-1%
R509
250V 0.1 ECQUL

1
R506_1 AC IN 120V_60Hz

47 1/4W
NC

4
R507
W830 4A 125V CD501

2
180 20W 0R614908
FH502 4A 125V FH501 CP501
R177 L501 THL-P03P-B1
D126 F501

160V 100 YXA

9-000074

2
1 BLACK

160V 10 YK
EM1C 1.5K 10W 233004

W822
2

C507_1
C519
C133 EYF-52BC EYF-52BC

WIDE
BLADE
WHITE
1KV 0.001 B

5 5

1/2W
R515

R501
W816
1.5 3W

200V 220 YK

820K
C132 25V 470 YK

C506
FROM/TO DEFLECTION/CRT
R147 W801
+B
D124 RD15FB1 33 1/2W
GND
+12V
SOUND+B D127
11E1N

1S2472
4

D125
FROM/TO MICON/TUNER RY101 3
ALKS321
X-RAY_TEST 1 2
+B
4 POWER 4
AT+12V
AUDIO_MUTE
GND

FROM/TO CHROMA

W802

47K
R357
+B C352 27 T351
AUDIO_OUT ETA24Z83AY
C354
16V 10 KA
GND 6 1 2
J351

R351

68K
270K
50V 1 YK

R353
5 3
R362 W845 W846 W847 HSJ1403-01-010
R354 R356 4 3 1
68 CD351
10K 100K
10V 470 YK

1/2W CPU2015A SPEAKER

3 6.0 0 0 0 3
0.018 M

C351

1 2 3 4 1 1
C357

AN7511
SOUND AMP

2 2
CP351_1
THL-P02P-A1 8 OHM 1.5W
SP351
IC351

811-08-194

8 7 6 5
W829 4.2 0 4.0 8.5

R363
28
2.2 1W
PCB010
2 TM8411 2
W851

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
1 WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES 1
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-7 G-8
 WAVEFORMS
MICON/TUNER

1 200mV. 5ms/div 6 0.5V. 20µs/div 11 1V. 0.5ms/div

2 0.5V. 20µs/div 7 0.5V. 20µs/div 12 20V. 20µs/div

3 200mV. 20µs/div 8 0.5V. 20µs/div 13 200mV. 20µs/div

4 200mV. 5ms/div 9 200mV. 20µs/div 14 0.5V. 5ms/div

CHROMA

5 0.5V. 2ms/div 10 0.5V. 20µs/div 15 1V. 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
 WAVEFORMS

16 1V. 20µs/div 21 200V. 20µs/div 26 50V. 20µs/div

POWER/SOUND AMP

17 1V. 20µs/div 22 10V. 5ms/div 27 50mV. 0.5ms/div

DEFLECTION/CRT

18 0.5V. 5ms/div 23 5V. 5ms/div 28 200mV. 0.5ms/div

19 20V. 20µs/div 24 50V. 20µs/div

20 2V. 20µs/div 25 50V. 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
 MECHANICAL EXPLODED VIEW
201
112

201
201

201

206 J801

120 111

206 201
116 PCB110
206 (CRT PCB ASS'Y)
L502
202

ATC001
206 205
V801 202 104 103

108
114 102
119 117 TU001
105
118

PCB010
(MAIN PCB ASS'Y)
204
110
109

204
107 203

115

113

SP351
106
101

I-1
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
101 A3H202C720 CABINET,FRONT ASS'Y
102 --- HEAT SINK
103 --- HEAT SINK
104 --- METAL SPACER
105 --- COATING CLIP
106 701WPJA543 CABINET,FRONT
107 713WPA0090 GUIDE,REMOCON
108 --- HEAT SINK
109 735WPA0381 BUTTON,FRAME

110 735WPA0382 BUTTON,HOLDER

111 702WPA0535 CABINET,BACK
112 722A08A031 SHEET,RATING
113 7230006818 SHEET,CAUTION
114 723000A930 FILM,DECORATION
115 735WPA0396 SPEAKER,HOLDER
116 741WUA0019 SPRING,EARTH
117 800WQ00044 FELT SHEET 5x50xT0.5
118 800WQ00045 FELT SHEET 5x150xT0.5
119 722000A023 SHEET,HWC

120 7220001059 SHEET,CSA WARNING

201 8117540A64 SCREW,TAPPING (B0) TRUSS 4x16

202 8117D30A04 SCREW,TAPPING (B0) WH8 BRAZIER 3x10
203 8110630A24 SCREW,TAP TITE (P) BRAZIER 3x12
204 8110630A04 SCREW,TAP TITE (P) BRAZIER 3x10
205 810A130804 SCREW/WASHER (A) M3x8
206 8121J50B54 SCREW,TAPPING (B0) GW20 5x28

--- JB5K0100 POLY BAG

--- J3H20201 INSTRUCTION BOOK
--- 791WHA0023 LAMIFILM BAG
--- 792WHA0225 PACKAGE,TOP
--- 792WHA0226 PACKAGE,BOTTOM
--- 793WCDA568 GIFT BOX

J1-1
 ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
RESISTORS ICS
! R177 R5Y2CF152J R, CEMENT 1.5K OHM 10W IC101 I53F53039B IC OEC3039B
R363 R3X1812R2J R, METAL OXIDE 2.2 OHM 1W ! IC103 I1K998L050 IC KIA78L05BP-AT
! R401 R4X5T4104F R, METAL 100K OHM 1/4W IC104 I9UJ0T600C IC PST600C
! R404 R903N8332J RC 3.3K OHM 1/8W IC199 A3H201A015 IC M24C01-BN6
! R405 R4X5T4183F R, METAL 18K OHM 1/4W ! IC201 I03FE76814 IC LA76814M-MPB
! R406 R903N8152J RC 1.5K OHM 1/8W ! IC351 I01DP75110 IC AN7511
! R407 R635821R5J R, FUSE 1.5 OHM 1/2W ! IC401 I03SD78400 IC LA7840
! R408 R4X5T6103F R, METAL 10K OHM 1/6W ! IC402 I1KA978050 IC KIA7805PI
! R409 R4X5T6123F R, METAL 12K OHM 1/6W ! IC501 I2B4901100 IC STR30110
R416 R0L2U2010J RC 1 OHM 1/2W ! IC601 I1KJ98L090 IC KIA78L09BP-AT
R417 R425T6113F R, METAL 11K OHM 1/6W TRANSISTORS
R418 R425T6103F R, METAL 10K OHM 1/6W Q101 TC5T018154 TRANSISTOR, SILICON 2SC1815Y(TPE2)
! R429 R655812R7J R, FUSE 2.7 OHM 1W Q102 TC5T018154 TRANSISTOR, SILICON 2SC1815Y(TPE2)
! R443 R6550A4R7J R, FUSE 4.7 OHM 2W Q103 TC5T018154 TRANSISTOR, SILICON 2SC1815Y(TPE2)
! R447 R3X18A392J R, METAL OXIDE 3.9K OHM 2W Q104 TCST02001L TRANSISTOR, SILICON 2SC2001(C)-T_L
! R448 R3X18A332J R, METAL OXIDE 3.3K OHM 2W ! Q401 TDUU025990 TRANSISTOR, SILICON 2SD2599(LBOEC1)
! R449 R3X18A392J R, METAL OXIDE 3.9K OHM 2W ! Q402 TC3T022710 TRANSISTOR, SILICON 2SC2271(D,E)-AE
R501 R21202105K R, SOLID 1M OHM 1/2W Q602 TA5T010154 TRANSISTOR, SILICON 2SA1015Y(TPE2)
! R502 R5Y2CE2R2J R, CEMENT 2.2 OHM 7W Q604 TA5T010154 TRANSISTOR, SILICON 2SA1015Y(TPE2)
! R506 R5Y2CH181J R, CEMENT 180 OHM 20W Q605 TA5T010154 TRANSISTOR, SILICON 2SA1015Y(TPE2)
! R507 R65584470J R, FUSE 47 OHM 1/4W ! Q801 TCKT1473A0 TRANSISTOR, SILICON 2SC1473A-TA-(RQ)
! R509 R4X5T6123F R, METAL 12K OHM 1/6W ! Q802 TCKT1473A0 TRANSISTOR, SILICON 2SC1473A-TA-(RQ)
! R515 R3X28B1R5J R, METAL 1.5 OHM 3W ! Q803 TCKT1473A0 TRANSISTOR, SILICON 2SC1473A-TA-(RQ)
! R606 R903N8103J RC 10K OHM 1/8W COILS &TRANSFORMERS
! R614 R3X28B182J R, METAL OXIDE 1.8K OHM 3W L201 021LA6100K COIL 10 UH
! R615 R3X28B182J R, METAL OXIDE 1.8K OHM 3W L202 0216731R0K COIL 1 UH
! R649 R3X28B182J R, METAL OXIDE 1.8K OHM 3W L205 0336020388 COIL, VIDEO IFT 3602038
! R803 R3X18A153J R, METAL OXIDE 15K OHM 2W L406 02186G180M COIL 18 UH
! R805 R3X18A153J R, METAL OXIDE 15K OHM 2W ! L501 029K000074 COIL, LINE FILTER 9-000074
! R807 R3X18A153J R, METAL OXIDE 15K OHM 2W ! L502 028F140025 COIL, DEGAUSS 8F140025
CAPACITORS L601 021LA6150K COIL 15 UH
! C404 E02LT1471M CE 470 UF 10V ! T351 045126001A TR, SOUND OUT PUT ETA24Z83AY
! C405 E02LT2471M CE 470 UF 16V T401 03305Y002S TRANS, HORIZONTALDRUVE 305Y002
! C412 E02LT1471M CE 470 UF 10V JACKS
! C414 E02LT4101M CE 100 UF 35V J351 0602121012 JACK, RCA 3.5 HSJ1403-01-010
C416 P3N1F2123J CPP 0.012 UF 200V ! J801 066X120014 SOCKET, CRT HPS3200-010501
! C418 E02LF3102M CE 1000 UF 25V SWITCHES
! C433 E02LT4471M CE 470 UF 35V SW101 0504201T31 SWITCH, TACT SKHVBED010
! C434 E02LT8220M CE 22 UF 100V SW102 0504201T31 SWITCH, TACT SKHVBED010
! C437 P411F3474J CMPP 0.47 UF 250V SW103 0504201T31 SWITCH, TACT SKHVBED010
! C442 C01BBP7H2K CC 220 PF 2KV BP SW104 0504201T31 SWITCH, TACT SKHVBED010
! C443 P414F9472H CMPP 0.0047 UF 1.6KV SW105 0504201T31 SWITCH, TACT SKHVBED010
! C446 E02LTB010M CE 1 UF 160V P.C.BOARD ASSEMBLIES
! C448 E02LT8220M CE 22 UF 100V PCB010 A3H202C01A PCB ASS'Y TM8411B
! C502 P2122B104M CMP 0.1 UF 250V PCB110 A3H202C11A PCB ASS'Y TC8270B
! C506 E02LFC221M CE 220 UF 200V MISCELLANEOUS
C507 E02YFB101M CE 100 UF 160V ANT001 125C108030 ANTENNA, ROD HPAS-2S780
! C615 E50HU2220M CE 22 UF 16V ! ATC001 0632400008 ANT, UNIT NXC0032-010010
C650 E0EE05100M CE 10 UF 50V CD351 06CPU2015A CORD, CONNECTOR CPU2015A
DIODES ! CD501 120R614908 CORD, AC 0R614908
D001 D94TA30013 DIODE, ZENER HZ30-3L TD CD802 122E052503 CORD, JUMPER 2E052503
D101 D1VT001330 DIODE, SILICON 1SS133T-77 CD803 122E042302 CORD, JUMPER 2E042302
D103 D97U05R61B DIODE, ZENER MTZJ5.6B T-77 CF201 1022T45R71 FILTER, SAW SAF45MFX220ZR
D124 D9201150B1 DIODE, ZENER RD15FB1 CP101 0694260139 CONNECTOR PCB SIDE 173979-6
D125 D1VT024720 DIODE, SILICON 1S2472T-77 CP351 0697U20029 CONNECTOR PCB SIDE THL-P02P-A1
! D126 D2BT0EM1C0 DIODE, SILICON EM1C V1 CP401 069X450029 CONNECTOR PCB SIDE B05B-DVS
D127 D28T11E1N1 DIODE, SILICON 11E1N-TA1B2 CP501 0697320039 CORD, UX CONNECTOR THL-P03P-B1
! D401 D94TA27011 DIODE, ZENER HZ27-1L TD CP502 069W420029 CONNECTOR PCB SIDE TV-50P-02-A1
! D402 D94TA11B11 DIODE, ZENER HZ11B1L TD CP801 069W010030 CONNECTOR PCB SIDE TBS-X01X-A1
D403 D28T11E1N1 DIODE, SILICON 11E1N-TA1B2 CP802A 067R005019 WIRE HOLDER 51048-0510
! D404 D2BTAU02A0 DIODE, SILICON AU02A V0 CP802B 067R005019 WIRE HOLDER 51048-0510
! D407 D2BTAU02A0 DIODE, SILICON AU02A V0 CP803A 067R104019 WIRE HOLDER 51052-0400
! D408 D2BTAU02A0 DIODE, SILICON AU02A V0 CP803B 067R104019 WIRE HOLDER 51052-0400
! D410 D2BTAU02A0 DIODE, SILICON AU02A V0 CUS001 800WF00004 CUSHION-A
! D411 D2BTAU02A0 DIODE, SILICON AU02A V0 ! F501 081PA04003 FUSE 233004-MB000
! D422 D2BTAU02A0 DIODE, SILICON AU02A V0 ! FB401 043214029F TRANSFORMER, FLYBACK 3214029F
! D501 D2BTRM11C0 DIODE, RECTIFIER RM11C FH501 06710T0006 HOLDER, FUSE EYF-52BC
! D502 D2BTRM11C0 DIODE, RECTIFIER RM11C FH502 06710T0006 HOLDER, FUSE EYF-52BC
! D503 D2BTRM11C0 DIODE, RECTIFIER RM11C MS501 128B000018 SHEET 23MICA
! D504 D2BTRM11C0 DIODE, RECTIFIER RM11C OS101 077Q014003 REMOTE RECEIVER PIC-28143SY-2
D602 D1VT001330 DIODE, SILICON 1SS133T-77 ! RY101 0560V20115 RELAY ALKS321
D603 D28T11E1N1 DIODE, SILICON 11E1N-TA1B2 ! SP351 070C132014 SPEAKER 811-08-194
D605 D94TA6RB12 DIODE, ZENER HZ6B2L TD ! TH501 DF20BG3R0Q DEGAUSS ELEMENT PTH451A100BG3R0Q
D606 D1VT001330 DIODE, SILICON 1SS133T-77 TM101 076R074150 TRANSMITTER R25-1028
D609 D1VT001330 DIODE, SILICON 1SS133T-77 ! TU001 0145S00049 TUNER, UHF-VHF ENV56D67G3
D610 D1VT001330 DIODE, SILICON 1SS133T-77 ! V801 098Y140497 COLOR PICTURE TUBE W/DY A34JXV70X28N45
X101 100C32R803 CRYSTAL DSVT-200 32.768KHz
X601 100CT3R505 CRYSTAL HC-49 /C 3.579545MHz

J2-1
 ELECTRICAL REPLACEMENT PARTS LIST

RESISTOR
RC...................... CARBON RESISTOR

CAPACITORS
CC...................... CERAMIC CAPACITOR
CE...................... ALUMI ELECTROLYTIC CAPACITOR
CP...................... POLYESTER CAPACITOR
CPP................... POLYPROPYLENE CAPACITOR
CPL.................... PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................. METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR

J2-1
SPEC.NO. M3H2-02C
O/R NO. K983018