Standard Tender Document For Provision of Motor and Alternator Rewinding Services Off Grid Power Station

Download as pdf or txt
Download as pdf or txt
You are on page 1of 80

TENDER NO. KP1/9A.1A/RT/039/18-19.

FOR PROVISION OF MOTOR AND ALTERNATOR REWINDING SERVICES


OFF GRID POWER STATION

MAY 2019

ALL TENDERERS ARE ADVISED TO READ CAREFULLY THIS TENDER


DOCUMENT IN ITS ENTIRETY BEFORE MAKING ANY BID

RESTRICTIVE TENDER DOCUMENT FOR SERVICES

THE KENYA POWER & LIGHTING COMPANY LIMITED


CENTRAL OFFICE, STIMA PLAZA,
KOLOBOT ROAD, PARKLANDS,
P.O. BOX 30099-00100,
NAIROBI,
KENYA.

Telephones: +254-020-3201000; 3644000 Pilot Lines


Telephones: +254 -720-600070/1-5; -733-755001/2-3 Cellular
Website: www.kplc.co.ke

.Email 1: [email protected]
2: [email protected]
3: [email protected]
4: [email protected]
2

TABLE OF CONTENTS
SECTION I - INVITATION TO TENDER ................................................................................................... 3
SECTION II - TENDER SUBMISSION CHECKLIST ................................................................................. 4
SECTION III - INSTRUCTIONS TO TENDERERS (ITT) .......................................................................... 8
SECTION IV - SCHEDULE OF REQUIREMENTS ...................................................................................27
SECTION V - PRICE SCHEDULE FOR SERVICES .................................................................................28
SECTION VI - EVALUATION CRITERIA.................................................................................................30
SECTION VII – GENERAL CONDITIONS OF CONTRACT ...................................................................33
SECTION VIII – SPECIAL CONDITIONS OF CONTRACT ....................................................................43
SECTION IX - TENDER FORM ..................................................................................................................44
SECTION X - CONFIDENTIAL BUSINESS QUESTIONNAIRE FORM .................................................46
SECTION XI A - TENDER SECURITY FORM – (BANK GUARANTEE) ..............................................49
SECTION XI B - TENDER SECURITY FORM (SACCO SOCIETY, DEPOSIT TAKING MICRO
FINANCE INSTITUTIONS, WOMEN ENTERPRISE FUND & YOUTH ENTERPRISE FUND) ...........52
SECTION XI C - TENDER SECURITY – (LETTERS OF CREDIT) .........................................................55
SECTION XII - MANUFACTURER’S/ PRINCIPAL’S AUTHORIZATION FORM ................................57
SECTION XIII - DECLARATION FORM ..................................................................................................58
SECTION XIV – DRAFT LETTER OF NOTIFICATION OF AWARD ....................................................59
SECTION XV – DRAFT LETTER OF NOTIFICATION OF REGRET .....................................................60
SECTION XVI - CONTRACT AGREEMENT FORM ................................................................................61
SECTION XVII A - PERFORMANCE SECURITY FORM (BANK GUARANTEE) ...............................66
SECTION XVII B - PERFORMANCE SECURITY (LC) ...........................................................................68
SECTION XVIII – SUBCONTRACTORS...................................................................................................70
SECTION XIX - PREVIOUS EXPERIENCE WITH SIMILAR WORK ....................................................71
SECTION XX - SUPPLIER EVALUATION FORM ...................................................................................72
SECTION XXI - THE DETAILS OF SERVICES ........................................................................................75

For provision of motor and alternator rewinding services off grid power station
3

SECTION I - INVITATION TO TENDER


MAY 2019

TENDER NUMBER KP1/9A.1A/RT/039/18-19 FOR PROVISION OF MOTOR


AND ALTERNATOR REWINDING SERVICES OFF GRID POWER STATION

1.1 The Kenya Power & Lighting Company Limited hereinafter referred to as KPLC
invites bids from eligible Tenderers for provision motor and alternator rewinding
services off grid power station. Tenderers may obtain further information from the
General Manager, Supply Chain, KPLC at Stima Plaza, 3rd Floor, Kolobot Road,
P.O. Box 30099 – 00100 Nairobi, Kenya.

1.2 Submission of Tender documents


Completed Tenders are to be submitted in electronic format on the KPLC’s E-
procurement portal on the due date and time published on the portal. Tenderers
are required to visit the portal from time to time for revised closing dates and
addendums. The Tender is to be submitted ONLINE on or before the submission
date and time indicated on the KPLC tendering portal.

1.3 Tenders will be opened thereafter.

1.4 Prices
Prices quoted should be inclusive of all taxes and delivery costs to the required
site (where applicable) and must be in Kenya Shillings or a freely convertible
currency in Kenya and shall remain valid for one hundred and twenty (120) days
from the closing date of the tender.
Please note that prices indicated on the KPLC tendering portal should be
exclusive of VAT

*1.6 Pre-bid meeting


There will be no pre-bid meeting for this tender.
.

For provision of motor and alternator rewinding services off grid power station
4

SECTION II - TENDER SUBMISSION CHECKLIST

Tender Submission Format


Bidders are advised to clearly label their documents while uploading on the portal.

No. Item Tick Where


Provided
1 Declaration Form
2 Duly completed Tender Form
3 Copy of Company or Firm’s Registration Certificate
4 Copy of PIN Certificate
5 Copy of Valid Tax Compliance Certificate
6 Confidential Business Questionnaire (CBQ)
7 Certificate of Confirmation of Directors and Shareholding
(C.R.12) for registered companies and if not a registered company
a business name for those trading as a sole proprietor or a
partnership registered under the Kenyan law or equivalent
certification for foreign tenderers.
8 Copy of the business permit
9 Names with full contact as well as physical addresses of previous
customers of similar goods and reference letters from at least three
(3) previous customers
10 Statement on Deviations
11 Price Schedule(s)
12 Schedule of requirements duly filled indicating services offered
13 Any other document or item required by the Tender Document.
(The Tenderer shall specify such other documents or items it has
submitted)
14 Sample viewing form duly filled

For provision of motor and alternator rewinding services off grid power station
5

*NOTES TO TENDERERS

1. Valid Tax Compliance Certificate shall be one issued by the relevant tax
authorities and valid for at least up to the tender closing date. All Kenyan
registered Tenderers must provide a valid Tax Compliance Certificate.

2. All Kenyan registered Tenderers must provide the Personal Identification Number
Certificate (PIN Certificate).

3. Foreign Tenderers must provide equivalent documents from their country of


origin as regards Tax Compliance and PIN certificates OR statements certifying
that the equivalent documentation is not issued in the Tenderer’s country of
origin. The Statement(s) that equivalent documentation is not issued by the
Tenderer’s country should be original and issued by the Tax authorities in the
Tenderer’s country of origin.

For provision of motor and alternator rewinding services off grid power station
6

TABLE OF PARAGRAPHS ON INSTRUCTIONS TO TENDERERS

Paragraph No. Headings Page No.

3.1 Definitions…………………………………………..…….…… 8
3.2 Eligible Tenderers………………………………………...…….9
3.3 Joint Venture……………………………………………………10
3.4 Cost of Tendering ………………………………………...…….11
3.5 Contents of the Tender Document………………………………11
3.6 Clarification of Documents………………………………...……12
3.7 Amendment of Documents……………………………….……..12
3.8 Language of Tender.……………………………………...….….13
3.9 Documents Comprising the Tender.……………………...……..13
3.10 Tender Form……………………………………………...……..13
3.11 Tender Prices ……………………………………………...……13
3.12 Tender Currencies……………………………………….…..…..14
3.13 Tenderer’s Eligibility and Qualifications……………….…..…..14
3.14 Conformity of Services to Tender Documents……………….....15
3.15 Demonstration(s), Inspections and Tests…………….………….15
3.16 Warranty…………………………………………………………16
3.17 Tender Security……………………………………….…….……16
3.18 Validity of Tenders …………………………………….…..……18
3.19 Alternative Offers.…………………………………….…….…..18
3.20 Number of Sets Of and Tender Format…………………..…….. 18
3.21 Preparation and Signing of The Tender…………………..……..18
3.22 Sealing and Outer Marking of Tenders…………………..……..
3.23 Deadline for Submission of Tender ..…………………….….….19
3.24 Modification and Withdrawal of Tenders……………….………19
3.25 Opening of Tenders………………………………………….…..19
3.26 Process To Be Confidential………………………………………20
3.27 Clarification of Tenders and Contacting KPLC…………………20
3.28 Preliminary Evaluation and Responsiveness………….………...20
3.29 Minor Deviations, Errors or Oversights…………………………21
3.30 Technical Evaluation and Comparison of Tenders…..…………..21
3.31 Financial Evaluation…………………………………………….. 21
3.32 Preferences………………………………………………………22
3.33 Tender Evaluation Period……………………………………….
3.34 Debarment of a Tenderer………………………………….……22

For provision of motor and alternator rewinding services off grid power station
7

3.35 Confirmation of Qualification for Award……………………..22


3.36 Award of Contract….………………………………………..…23
3.37 Termination of Procurement Proceedings………………………23
3.38 Notification of Award……………………………………………23
3.39 Signing of Contract ……………………………………….…….. 23
3.40 Performance Security ……………………………………………24
3.41 Corrupt or Fraudulent Practices……..…………………………… 25

For provision of motor and alternator rewinding services off grid power station
8

SECTION III - INSTRUCTIONS TO TENDERERS (ITT)


3.1 Definitions
In this tender, unless the context or express provision otherwise requires: -
a) Any reference to any Act shall include any statutory extension,
amendment, modification, re-amendment or replacement of such Act and
any rule, regulation or order made there-under.
b) “Date of Tender Document” shall be the start date specified on the KPLC
tendering portal.
c) “Day” means calendar day and “month” means calendar month.
d) “KEBS” wherever appearing means the Kenya Bureau of Standards or its
successor(s) and assign(s) where the context so admits.
e) “KENAS” wherever appearing means the Kenya National Accreditation
Service or its successor(s) and assign(s) where the context so admits
f) “PPRA” wherever appearing means The Public Procurement Regulatory
Authority or its successor(s) and assign(s) where the context so admits.
g) Reference to “the tender” or the “Tender Document” includes its
appendices and documents mentioned hereunder and any reference to this
tender or to any other document includes a reference to the other
document as varied supplemented and/or replaced in any manner from
time to time.
h) “The Procuring Entity” means The Kenya Power and Lighting Company
Limited or its successor(s) and assign(s) where the context so admits
(hereinafter abbreviated as KPLC).
i) “The Tenderer” means the person(s) submitting its Tender for the supply,
installation and commissioning (where applicable) of the goods in
response to the Invitation to Tender.
j) Where there are two or more persons included in the expression the
“Tenderer”, any act or default or omission by the Tenderer shall be
deemed to be an act, default or omission by any one or more of such
persons.
k) Words importing the masculine gender only, include the feminine gender
or (as the case may be) the neutral gender.
l) Words importing the singular number only include the plural number and
vice-versa and where there are two or more persons included in the
expression the “Tenderer” the covenants, agreements and obligations
expressed to be made or performed by the Tenderer shall be deemed to be
made or performed by such persons jointly and severally.

For provision of motor and alternator rewinding services off grid power station
9
m) KPLC’s “authorised person” shall mean its MD & CEO who is
designated by the PPAD Act 2015 to exercise such power, authority or
discretion as is required under the tender and any contract arising
therefrom, or such other KPLC staff delegated with such authority.
n) Citizen contractors-means a person/firm wholly owned and controlled by
person(s) who are citizens of Kenya.
o) Local contractors- a firm shall be qualified as a local contractor if it is
registered in Kenya.
3.2 Eligible Tenderers
3.2.1 A tenderer is eligible to bid for this contract only if the tenderer satisfies the
following criteria—
(a) the tenderer has the legal capacity to enter into a contract for
procurement or asset disposal;
(b) the tenderer is not insolvent, in receivership, bankrupt or in the process
of being wound up;
(c) the tenderer, if a member of a regulated profession, has satisfied all the
professional requirements;
(d) the tenderer and his or her sub-contractor, if any, is not debarred;
(e) the tenderer has fulfilled tax obligations;
(f) the tenderer has not been convicted of corrupt or fraudulent practices;
and
(g) is not guilty of any serious violation of fair employment laws and
practices.

In addition, this Invitation to Tender is open to all Tenderers eligible as described


in the
Appendix to Instructions to Tenderers.

Successful Tenderers shall provide the services in accordance with this tender and
the ensuing contract.
3.2.2 Collusion or Agreements between eligible tenderers to directly or indirectly fix
prices or any other trading conditions is prohibited. Where this is discovered, the
tenderers involved will not be eligible for award and shall be disqualified.

3.2.3 Notwithstanding any other provisions of this tender, the following are not eligible
to participate in the tender:-
a) KPLC’s employees, its Board or any of its committee members.
b) Any Public/State Officer of the Government of the Republic of Kenya
(GoK).
c) Any member of a Board or Committee or any department of GoK.
d) Any person appointed to any position by the President of Kenya.
e) Any person appointed to any position by any Cabinet Secretary of GoK.

For provision of motor and alternator rewinding services off grid power station
10
f) Any tenderer submitting false, inaccurate or incomplete information
about their qualifications.

3.2.4 In addition the tenderer shall be considered ineligible to bid, where in case of a
corporation, private company, partnership or other body, the tenderer, their
spouse, child or sub-contractor has substantial or controlling interest and is found
to be in contravention of the provisions of section 3.2.1 above.

3.2.5 Despite the provisions of section 3.2.3 and 3.2.4, a tenderer having a
substantial or controlling interest shall be eligible to bid where—
(a) such tenderer has declared any conflict of interest; and
(b) performance and price competition for that good, work or service is
not available or can only be sourced from that tenderer.

3.2.6 For the purposes of this paragraph, any relative i.e. spouse(s) and child(ren) of
any person mentioned in sub-paragraph 3.2.3 is also ineligible to participate in the
tender. In addition, a Cabinet Secretary shall include the President, Deputy
President or the Attorney General of GoK.
3.2.7 Tenderers shall provide the qualification information statement that the Tenderer
(including subcontractors) is not associated, or have been associated in the past,
directly or indirectly, with a firm or any of its affiliates which have been engaged
by KPLC to provide consulting services for the preparation of the design,
specifications, and other documents to be used for the procurement of the goods
under this Invitation to Tender.
3.2.8 Tenderers shall not be under declarations as prescribed at Section XIII.
3.2.9 Tenderers who are not under these declarations shall complete the Declaration
Form strictly in the form and content as prescribed at Section XIII.
3.2.10 Those that are under the Declaration as prescribed at Section XIII whether
currently or in the past shall not complete the Form. They will submit a suitable
Form giving details, the nature and present status of their circumstances.

3.3 Joint Venture


3.3.1 Tenders submitted by a joint venture of two or more firms, as partners shall
comply with the following requirements: -
a) the Tender Form and in case of a successful tender, the Contract
Agreement Form, shall be signed so as to be legally binding on all partners
of the joint venture.
b) one of the partners shall be nominated as being lead contractor, and this
authorization shall be evidenced by submitting a Power of Attorney signed
by legally authorized signatories of all the partners.
c) The Power of Attorney which shall accompany the tender, shall be granted
by the authorized signatories of all the partners as follows:-

For provision of motor and alternator rewinding services off grid power station
11
(i.) for local bidders, before a Commissioner of Oaths or a
Notary Public or Magistrate of the Kenyan Judiciary.
(ii.) for a foreign bidder, before a Notary Public, or the equivalent of a
Notary Public, and in this regard the bidder shall provide
satisfactory proof of such equivalence.
d) the lead contractor shall be authorized to incur liability and receive
instructions for and on behalf of any and all the partners of the joint
venture and the entire execution of the contract including payment shall be
done exclusively with the lead contractor.
3.3.2 All partners of the joint venture shall be liable jointly and severally for the
execution of the contract in accordance with the contract terms, and a relevant
statement to this effect shall be included in the authorization mentioned in
paragraph 3.3.1 (b) above as well as in the Form of Tender and the Contract
Agreement Form (in case of the accepted tender).
3.3.3 A copy of the agreement entered into by the joint venture partners shall be
submitted with the tender.

3.4 Cost of Tendering


3.4.1 The Tenderer shall bear all costs associated with the preparation and submission
of its Tender, and KPLC will in no case be responsible or liable for those costs,
regardless of the conduct or outcome of the tendering process.

3.5 Contents of the Tender Document


3.5.1 The Tender Document comprises the documents listed below and Addendum
(where applicable) issued in accordance with paragraph 3.7 of these Instructions
to Tenderers: -
a) Invitation to Tender
b) Tender Submission Checklist
c) Instructions to Tenderers
d) Appendix to Instructions to Tenderers
e) Schedule of Requirements
f) Project Implementation Schedule
g) Price Schedule for Services
h) Evaluation Criteria
i) General Conditions of Contract
j) Special Conditions of Contract
k) Tender Form

l) Confidential Business Questionnaire Form


m) Tender Security Form
n) Manufacturer’s Authorization Form
For provision of motor and alternator rewinding services off grid power station
12
o) Manufacturer’s Warranty
p) Declaration Form
q) Contract Form
r) Performance Security Form
s) Details of Service
(i.) General Requirements
(ii.) Specific Details of Services

3.5.2 The Tenderer is expected to examine all instructions, forms, provisions, terms and
specifications in the Tender Document. Failure to furnish all information required
by the Tender Document or to submit a tender not substantially responsive to the
Tender Document in every respect will be at the Tenderer’s risk and may result in
the rejection of its Tender.
3.5.3 All recipients of the documents for the proposed Contract for the purpose of
submitting a tender (whether they submit a tender or not) shall treat the details of
the documents as “Private and Confidential”.

3.6 Clarification of Documents


A prospective Tenderer requiring any clarification of the Tender Document may
notify the General Manager Supply Chain in writing and ensure receipt is
acknowledged at KPLC’s Physical address indicated on the Tender Document.
KPLC will respond in writing to any request for clarification of the Tender
documents, which it receives not later than seven (7) days prior to the deadline for
the submission of Tenders, prescribed by KPLC. Written copies of KPLC’s
response (including an explanation of the query but without identifying the source
of inquiry) will be published and accessible to all prospective Tenderers on the
KPLC’s tendering portal.

3.7 Amendment of Documents


3.7.1 At any time prior to the deadline for submission of Tenders, KPLC, for any
reason, whether at its own initiative or in response to a clarification requested by a
prospective Tenderer, may modify the tender documents by amendment.
3.7.2 All prospective Tenderers that have registered in the portal for the Tender will be
notified of the amendment(s) (hereinafter referred to or otherwise known as
addendum) in writing and will be binding on them.
3.7.3 In order to allow prospective Tenderers reasonable time in which to take the
amendment into account in preparing their Tenders, KPLC, at its discretion, may
extend the deadline for the submission of Tenders.

For provision of motor and alternator rewinding services off grid power station
13
3.8 Language of Tender
The Tender prepared by the Tenderer, as well as all correspondence and
documents relating to the tender, exchanged between the Tenderer and KPLC,
shall be written in English language. Any printed literature furnished by the
Tenderer written in any other language shall be accompanied by an accurate
English translation of the relevant passages, in which case, for purposes of
interpretation of the Tender, the English translation shall govern. The English
translation shall be on the Tenderer’s letterhead and shall be signed by the duly
authorized signatory signing the Tender and stamped with the Tenderer’s stamp.

3.9 Documents Comprising the Tender


The Tender prepared and submitted by the Tenderers shall include but not be
limited to all the following components: -
a) Declaration Form, Tender Form and a Price Schedule completed in
compliance with paragraphs 3.2, 3.10, 3.11 and 3.12.
b) Documentary evidence established in accordance with paragraph 3.13
that the Tenderer is eligible to tender and is qualified to perform the
contract if its tender is accepted.
c) Documentary evidence established in accordance with paragraph 3.14
that the services and any ancillary thereto to be provided by the Tenderer
conform to the tender documents, and,
d) Tender Security furnished in accordance with paragraph 3.17
e) A detailed list of previous customers as prescribed for similar services on
tender and their contact addresses shall be submitted with the Tender for
the purpose of reference, or for evaluation where the Details of Service so
dictate.
f) And all other documents indicated in Section II (Tender Submission
Checklist)

3.10 Tender Form


The Tenderer shall complete and sign the Tender Form and all other documents
furnished in the Tender Document, indicating the services to be performed, a brief
description of the services, quantity (where applicable), and prices amongst other
information required.

3.11 Tender Prices


3.11.1 The Tenderer shall indicate on the appropriate Price Schedule, the unit prices
(where applicable) and total tender price of the services it proposes to provide
under the contract.

For provision of motor and alternator rewinding services off grid power station
14
3.11.2 Prices indicated on the Price Schedule shall be of all costs for the
services including insurances, duties, Value Added Tax (V.A.T) and other taxes
payable. No other basis shall be accepted for evaluation, award or otherwise.
3.11.3 Section 20 of the Insurance Act Cap 487 requires all imports to the country to be
insured with a local insurance company. It is now mandatory for all marine cargo
imports to adhere to this requirement.
3.11.4 Tender prices to be submitted (quoted) by the Tenderer shall remain fixed for
the contract duration.
3.11.5 A price that is derived by a disclosed incorporation or usage of an international
accepted standard formula shall be acceptable within the meaning of this
paragraph.
3.12 Tender Currencies
3.12.1 For services that the Tenderer will provide from within or outside Kenya, the
prices shall be quoted in Kenya Shillings, or in another freely convertible
currency in Kenya. The currency quoted must be indicated clearly on the Price
Schedule of Services.
3.12.2 The exchange rate to be used for currency conversion shall be the Central Bank of
Kenya selling rate prevailing on the Tender closing date. (Please visit the Central
Bank of Kenya website).

3.13 Tenderer’s Eligibility and Qualifications


3.13.1 Pursuant to paragraph 3.2, the Tenderer shall furnish, as part of its Tender,
documents establishing the Tenderer’s eligibility to tender and its qualifications to
perform the contract if its Tender is accepted.
3.13.2 The documentary evidence of the Tenderer’s qualifications to perform the
contract if its Tender is accepted shall be established to KPLC’s satisfaction –
a) that, in the case of a Tenderer offering to perform the services under the
contract which the Tenderer is not the Principal, the Tenderer has been
duly authorized by the Manufacturer, Principal or Producer to provide the
services. The authorization shall strictly be in the form and content as
prescribed in the Manufacturer’s or Principal’s Authorization Form in the
Tender Document
b) that the Tenderer has the financial capability necessary to perform the
contract. The Tenderer shall be required to provide the documents as
specified in the Appendix to Instructions to Tenderers including a current
Tax Compliance Certificate issued by the relevant tax authorities.
c) that the Tenderer has the technical and production capability necessary to
perform the contract.
d) that, in the case of a Tenderer not doing business within Kenya, the
Tenderer is or will be (if awarded the contract) represented by an agent in
Kenya equipped, and able to carry out the Tenderer’s maintenance,
For provision of motor and alternator rewinding services off grid power station
15
repair, spare parts and stocking obligations prescribed in the
Conditions of Contract and or in the Details of Service.
e) that the Tenderer is duly registered and is a current member of a
recognized body or institution accredited and or pertaining to that service.

3.13.3 The Tenderer will furnish KPLC with a copy of the accreditation or recognition
certificate as applicable. KPLC reserves the right to subject the certificate to
authentication.
3.13.4 Tenderers with a record of unsatisfactory or default in performance obligations in
any contract shall not be considered for evaluation or award. For the avoidance of
doubt, this shall include any Tenderer with unresolved case(s) in its obligations
for more than two (2) months in any contract.

3.14 Conformity of Services to Tender Documents


3.14.1 The Tenderer shall furnish, as part of its tender, documents establishing the
conformity to the Tender Document of all services that the Tenderer proposes to
perform under the contract.
3.14.2 The documentary evidence of conformity of the services to the Tender Document
may be in the form of literature, drawings, and data, and shall (where applicable)
consist of: -
a) a detailed description of the essential technical and performance
characteristics of the services whether in catalogues, drawings or
otherwise,
b) a list giving full particulars, including available source and current prices
of spare parts, special tools and other incidental apparatus necessary for
the proper and continuing performance of the services for a minimum
period of two (2) years following commencement of the provision of the
services to KPLC, and,
c) duly completed Statement of Compliance to KPLC’s Details of Service
demonstrating substantial responsiveness of the service to those Details
or, a statement of deviations and exceptions to the provisions of the
Details of Service.
3.14.3 For purposes of the documentary and other evidence to be furnished pursuant to
sub-paragraphs 3.14.1, 3.14.2 and paragraph 3.15, the Tenderer shall note that
standards for workmanship, material, and equipment, designated by KPLC in its
Details of Service are intended to be descriptive only and not restrictive. The
Tenderer may adopt higher standards in its Tender, provided that it demonstrates
to KPLC’s satisfaction that the substitutions ensure substantial equivalence to
those designated in the Details of Service.

3.15 Demonstration(s), Inspection(s) and Test(s)


For provision of motor and alternator rewinding services off grid power station
16
3.15.1 Where required in the tender, all Tenderers shall demonstrate ability of
performance of the required service in conformity with the Details of Services.
3.15.2 KPLC or its representative(s) shall have the right to inspect/ test the Tenderer’s
capacity, equipment, premises, and to confirm their conformity to the tender
requirements. This shall include the quality management system. KPLC’s
representative(s) retained for these purposes shall provide appropriate
identification at the time of such inspection/ test.
3.15.3 KPLC shall meet its own costs of the inspection/ test. Where conducted on the
premises of the Tenderer(s), all reasonable facilities and assistance, including
access to drawings and production data, shall be furnished to the inspectors at no
charge to KPLC.
3.15.4 Demonstration, Inspection/ Test Report(s) shall be completed upon conclusion of
the inspection/ tests. This Report will be considered at time of evaluation and or
award.

3.16 Warranty
3.16.1 Where required in the Tender, all Tenderers must also provide a Warranty that
services to be rendered in the Tenderer’s bid have no defect arising from
manufacture, materials or workmanship or from any act or omission of the
Tenderer that may develop under normal use or application of the services under
the conditions obtaining in Kenya.
3.16.2 This warranty will remain valid for the period indicated in the special conditions
of contract after the services, or any portion thereof as the case may be, have been
rendered.

3.17 Tender Security


3.17.1 The Tenderer shall furnish, as part of its Tender, a tender security for the amount
specified in the Appendix to Instructions to Tenderers. The Original Tender
Security, in a clearly labelled envelop, shall be deposited in the Tender Security
Box in Stima Plaza Supply Chain 3rd Floor on or before the opening date and time
and receipt acknowledged by KPLC evidenced by a stamped copy.

3.17.2 The tender security shall be either one or a combination of the following:-
a) an original Bank Guarantee that is strictly in the form and content as
prescribed in the Tender Security Form (Bank Guarantee) in the Tender
Document.
b) For Local bidders, Standby Letters of Credit (LC). All costs, expenses and
charges levied by all banks party to the LC shall be prepaid/borne by the
Tenderer. The LC must contain all the mandatory conditions of payment
to KPLC as prescribed in the Tender Security (Letters of Credit) provided
in the Tender Document.

For provision of motor and alternator rewinding services off grid power station
17
c) For Foreign bidders, Standby Letters of Credit (LC) confirmed
by a bank in Kenya. All costs, expenses and charges levied by all banks
party to the LC including confirmation charges shall be prepaid/borne by
the Tenderer. The LC must contain all the mandatory conditions of
payment to KPLC as prescribed in the Tender Security (Letters of Credit)
provided in the Tender Document.
d) An original Guarantee by a deposit taking Microfinance Institution, Sacco
Society, Youth Enterprise Development Fund or the Women Enterprise
Fund, that is strictly in the form and content as prescribed in the Tender
Security Form

3.17.3 The tender security is required to protect KPLC against the risk of the Tenderer’s
conduct which would warrant the security’s forfeiture pursuant to paragraph
3.17.10.
3.17.4 The Tender Security shall be denominated in Kenya Shillings or in another freely
convertible currency in Kenya. A Tender Security in form of a Bank Guarantee or
a Standby Letter of Credit issued on behalf of local bidders, should be from a
commercial bank licensed by the Central Bank of Kenya. A Tender Security in
form of a Standby Letter of Credit issued on behalf of foreign bidders by foreign
banks, should be confirmed by a commercial bank licensed by the Central Bank
of Kenya.
3.17.5 The Tender Security shall be valid for thirty (30) days beyond the validity of the
tender.
3.17.6 KPLC shall seek authentication of the Tender Security from the issuing bank. It is
the responsibility of the Tenderer to sensitize its issuing bank on the need to
respond directly and expeditiously to queries from KPLC. The period for response
shall not exceed five (5) days from the date of KPLC’s query. Should there be no
conclusive response by the bank within this period, such Tenderer’s Tender
Security may be deemed as invalid and the bid rejected.
3.17.7 Any Tender not secured in accordance with this paragraph will be rejected by
KPLC as non-responsive, pursuant to paragraph 3.28.
3.17.8 The unsuccessful Tenderer’s Tender Security will be released as promptly as
possible, in any of the following circumstances: -
a) the procurement proceedings are terminated
b) KPLC determines that none of the submitted Tenders is responsive
c) a contract for the procurement is entered into.
3.17.9 The successful Tenderer’s Tender Security will be released upon the successful
Tenderer’s signing the contract, pursuant to paragraph 3.39 and furnishing an
authentic Performance Security, pursuant to paragraph 3.40.
3.17.10 The Tender Security shall be forfeited –

For provision of motor and alternator rewinding services off grid power station
18
a) if the Tenderer withdraws its Tender after the deadline for submitting
Tenders but before the expiry of the period during which the Tenders must
remain valid
b) if the Tenderer fails to enter into a written contract in accordance with
paragraph 3.39
c) if the successful Tenderer fails to furnish the performance security in
accordance with paragraph 3.40
d) if the Tenderer fails to extend the validity of the tender security where
KPLC has extended the tender validity period in accordance with
paragraph 3.18.

3.18 Validity of Tenders


3.18.1 Tenders shall remain valid for one hundred and twenty days (120) days after the
date of tender opening as specified in the Invitation to Tender or as otherwise may
be prescribed by KPLC, pursuant to paragraph 3.23. A Tender that is valid for a
shorter period shall be rejected by KPLC as non-responsive.
3.18.2 In exceptional circumstances, KPLC may extend the Tender validity period. The
extension shall be made in writing. The tender security provided under paragraph
3.17 shall also be extended. A Tenderer shall not be required nor permitted to
modify its tender during the extended period

3.19 Alternative Offers


Only main offers shall be considered, as alternative offers are not acceptable.

3.20 Number of sets of and Tender Format

3.21 Preparation and Signing of the Tender


3.21.1 The Tender shall be typed or written in indelible ink. It shall be signed by the
Tenderer or a person or persons duly authorized to bind the Tenderer to the
contract.
3.21.2 The authorization shall be indicated by a written Power of Attorney granted by
the Tenderer to the authorized person before any of the following persons:-
a) For local Tenderers, a Commissioner of Oaths or a Notary Public or a
Magistrate of the Kenyan Judiciary.
b) For foreign Tenderers, a Notary Public in the country of the Tenderer.
In either case above, the Power of Attorney shall accompany the Tender.
3.21.3 All pages of the Tender, including un-amended printed literature, shall be
initialled by the person or persons signing the Tender and serially numbered.

For provision of motor and alternator rewinding services off grid power station
19
3.21.4 The Tender shall have no interlineations, erasures, or overwriting
except as necessary to correct errors made by the Tenderer, in which case such
corrections shall be initialled by the person or persons signing the Tender.
3.21.5 KPLC will assume no responsibility whatsoever for the Tenderer’s failure to
comply with or observe the entire contents of this paragraph 3.21.
3.21.6 Any Tender not prepared and signed in accordance with this paragraph may be
rejected by KPLC as non-responsive, pursuant to paragraph 3.21.

3.23 Deadline for Submission of Tenders


3.23.1 Tenders must be received by KPLC by the date and time specified in KPLC’s
tendering portal in PDF form.
3.23.2 KPLC may, at its discretion, extend this deadline for submission of Tenders by
amending the tender documents in accordance with paragraph 3.7, in which case
all rights and obligations of KPLC and the Tenderer previously subject to the
initial deadline, will therefore be subject to the deadline as extended.

3.24 Modification and Withdrawal of Tenders


3.24.1 The Tenderer may modify or withdraw its Tender after it has submitted, provided
that the modification, including substitution or withdrawal of the Tender is
received by KPLC prior to the deadline prescribed for submission of tenders.
3.24.2 No Tender may be modified after the deadline for submission of Tenders.
3.24.3 No Tender may be withdrawn in the interval between the deadline for submission
of tenders and the expiration of the period during which the Tender must remain
valid except where KPLC extends the initial validity period. Any withdrawal of a
Tender during this interval shall result in forfeiture of the Tenderer’s Tender
Security except where KPLC extends the initial validity period.

3.25 Opening of Tenders


3.25.1 KPLC shall open all Tenders promptly at the date and time specified in the KPLC
tendering portal and at the location specified in the Invitation to Tender or as may
otherwise be indicated.
3.25.2 The Tenderer’s names, tender modifications or withdrawals, the presence or
absence of requisite Tender Security and such other details as KPLC, at its
discretion, may consider appropriate, will be announced at the opening.
3.25.3 At the Tender opening, tender prices, discounts, and such other details as KPLC,
at its discretion, may consider appropriate will be read out.

3.25.4 The Tenderers or their representatives may attend the opening and those present
shall sign a register evidencing their attendance.

For provision of motor and alternator rewinding services off grid power station
20
3.26 Process to be Confidential
3.26.1 After the opening of tenders, information relating to the examination,
clarification, evaluation and comparisons of tenders and recommendations arising
there-from shall not be disclosed to a Tenderer or other person(s) not officially
concerned with such process until conclusion of that process.
3.26.2 Conclusion of that process shall be deemed to have occurred, at the latest, by the
date and time KPLC notifies the successful bidder(s). In any event, official
disclosure by KPLC of any information upon conclusion of that process may only
be to the unsuccessful bidders and may contain only the information permissible
by law in summary form.
3.26.3 Any effort by a Tenderer to influence KPLC or any of its staff members in the
process of examination, evaluation and comparison of tenders and information or
decisions concerning the Tender may result in the disqualification of the
Tenderer.

3.27 Clarification of Tenders and Contacting KPLC


3.27.1 To assist in the examination, evaluation and comparison of Tenders KPLC may,
at its discretion, ask the Tenderer for a clarification of its Tender. The request for
clarification and the response shall be in writing, and no change in the prices or
substance of the Tender shall be sought, offered, or permitted.
3.27.2 The Tenderer is required to provide timely clarification or substantiation of the
information that is essential for effective evaluation of its qualifications. It is the
responsibility of the Tenderer to provide in writing the clarification or
substantiation which should reach KPLC within five (5) days from the date of
KPLC’s query. Such writing may include by electronic mail or postal mail.
Should there be no conclusive response within this period, it shall result in the
Tenderer’s disqualification.
3.27.3 Save as is provided in this paragraph and paragraph 3.26 above, no Tenderer shall
contact KPLC on any matter related to its Tender, from the time of the tender
opening to the time the successful Tenderer is announced..
3.27.4 Any effort by a Tenderer to influence KPLC in its decisions on tender evaluation,
tender comparison, tender recommendation(s) or signing of Agreement may result
in the disqualification of the Tenderer.

3.28 Preliminary Evaluation and Responsiveness


3.28.1 Prior to the detailed Technical and Financial evaluation, KPLC will determine the
substantial responsiveness of each Tender. For purposes of this tender, a
substantially responsive Tender is one that conforms to the requirements of
Preliminary Evaluation. KPLC’s determination of a Tender’s responsiveness is to
be based on the contents of the Tender itself without recourse to extrinsic
evidence.
For provision of motor and alternator rewinding services off grid power station
21
3.28.2 KPLC will examine the Tenders to determine whether they conform to the
Preliminary Evaluation Criteria set out in Section VI Evaluation Criteria.
3.28.3 Notwithstanding the contents of the foregoing sub-paragraphs, if a Tender is not
substantially responsive, it will be rejected at the earliest stage of evaluation by
KPLC and cannot subsequently be made responsive by the Tenderer by correction
of any non–conformity.

3.29 Minor Deviations, Errors or Oversights


3.29.1 KPLC may waive any minor deviation in a Tender that does not materially depart
from the requirements of the goods and or services set out in the Tender
Document.
3.29.2 Such minor deviation -
3.29.2.1 shall be quantified to the extent possible,
3.29.2.2 shall be taken into account in the evaluation process, and,
3.29.2.3 shall be applied uniformly and consistently to all qualified Tenders duly
received by KPLC.
3.29.3 KPLC may waive errors and oversights that can be corrected without affecting the
substance of the Tender.

3.30 Technical Evaluation and Comparison of Tenders


3.30.1 KPLC will further evaluate and compare the Tenders that have been determined
to be substantially responsive, in compliance to the Details of Services set out in
the Tender Document and as per the prescribed Evaluation Criteria.
3.30.2 The Operational Plan is a critical aspect of the Tender. KPLC requires that the
Services shall be performed at the time specified in the Schedule of
Requirements. KPLC’s evaluation of a tender will also take into account the
Operational Plan proposed in the Tender. Tenderers offering to perform longer
than KPLC’s required delivery time will be treated as non-responsive and
rejected.

3.31 Financial Evaluation


3.31.1 The financial evaluation and comparison shall be as set out in the Summary of
Evaluation Process. The comparison shall be
a) of the price including all costs as well as duties and taxes payable on all
the materials to be used in the provision of the Services.
b) deviations in Payment Schedule from that specified in the Special
Conditions of Contract
3.31.2 Where other currencies are used, KPLC will convert those currencies to the
same currency using the selling exchange rate ruling on the date of tender closing
provided by the Central Bank of Kenya.

For provision of motor and alternator rewinding services off grid power station
22
3.32 Preferences
3.32.1 Subject to availability and realization of the applicable international or local
standards, only such manufactured articles, materials or supplies wholly mined
and produced in Kenya shall be subject to preferential procurement.

3.32.2 Despite the above provisions, preference shall be given to —


(a) manufactured articles, materials and supplies partially mined or produced in
Kenya or where applicable have been assembled in Kenya; or
(b) firms where Kenyans are shareholders.

3.32.3 The threshold for the provision under 3.30.2 (b) shall be above fifty-one percent
of Kenyan shareholders.

3.32.4 In the evaluation of tenders, exclusive preference shall firstly be given to citizen
contractors where the amount of the tender as evaluated is below Ksh. 500
Million in respect of works, goods and services.
3.32.5 Where a person is entitled to more than one preference scheme, the scheme with
the highest advantage to the person shall be applied.
3.32.6 For purposes of this paragraph the Tenderer shall submit with its Tender, a valid
copy of certificate of Confirmation of Directorships and Shareholding issued and
signed by either the Registrar of Companies or Registrar of Business Names. This
certificate must not be more than three (3) months old from the Date of the
Tender Document. Kenya Power reserves the right to subject the certificate to
authentication.

3.34 Debarment of a Tenderer


A Tenderer who gives false information in the Tender about its qualification or
who refuses to enter into a contract after notification of contract award shall be
considered for debarment from participating in future public procurement.

3.35 Confirmation of Qualification for Award


3.35.1 KPLC may confirm to its satisfaction whether the Tenderer that is selected as
having submitted the lowest evaluated responsive tender is qualified to perform
the contract satisfactorily.
3.35.2 The confirmation will take into account the Tenderer’s financial, technical, and
performance capabilities. It will be based upon an examination of the
documentary evidence of the Tenderer’s qualifications submitted by the Tenderer,
pursuant to paragraph 3.13 as well as confirmation of such other information as
KPLC deems necessary and appropriate. This may include factory, office and
other facilities inspection and audits.
3.35.3 An affirmative confirmation will be a prerequisite for award of the contract to
For provision of motor and alternator rewinding services off grid power station
23
the Tenderer. A negative confirmation will result in rejection of the
Tenderer’s Tender, in which event KPLC will proceed to the next lowest
evaluated responsive tender to make a similar confirmation of that Tenderer’s
capabilities to perform satisfactorily.

3.36 Award of Contract


3.36.1 KPLC will award the contract to the successful Tenderer whose Tender has been
determined to be substantially responsive, compliant with the evaluation criteria
and has been determined to be the lowest evaluated tender, and further, where
deemed necessary, that the Tenderer is confirmed to be qualified to perform the
contract satisfactorily.
3.36.2 Award will be done as indicated in the Appendix to Instructions to Tenderers.

3.37 Termination of Procurement Proceedings


3.37.1 KPLC may at any time terminate procurement proceedings before contract award
and shall not be liable to any person for the termination.
3.37.2 KPLC shall give prompt notice of the termination to the Tenderers, and, on
request from any Tenderer, give its reasons for termination within fourteen (14)
days of such request.

3.38 Notification of Award


3.38.1 Prior to the expiration of the period of tender validity, KPLC shall notify the
successful Tenderer in writing that its Tender has been accepted.
3.38.2 The notification of award shall not constitute the formation of the contract until
one is finally signed by both parties.
3.38.3 Simultaneously, and without prejudice to the contents of paragraph 3.27, on
issuance of Notification of Award to the successful Tenderer, KPLC shall notify
each unsuccessful Tenderer.
3.38.4 A notification of the tender outcome does not reduce the validity period for any
tender security whether the Tenderer is successful or not, except where such
tender security is officially released to the Bank and/or the Tenderer and such
Bank discharged of all its obligations by KPLC prior to the expiry of its stated
validity period.

3.39 Signing of Contract


3.39.1 At the same time as KPLC notifies the successful Tenderer that its Tender has
been accepted, KPLC will send the Tenderer the Contract Agreement provided in
the Tender Document together with any other necessary documents incorporating
all agreements between the Parties.

For provision of motor and alternator rewinding services off grid power station
24
3.39.2 Within fourteen (14) days of the date of notification of award, the successful
Tenderer shall only sign the Contract Form and all the documents specified in that
Form and return them to KPLC within that period of fourteen (14) days.
3.39.3 KPLC shall sign and date the Contract in the period between not earlier than
fourteen (14) days from the date of notification of contract award. Further, KPLC
shall not sign the contract until and unless the authentic performance security is
received in accordance with paragraph 3.39.
3.39.4 Failure of the successful Tenderer to sign the Contract, the award shall be
annulled and its tender security forfeited in which event KPLC shall notify the
next lowest evaluated Tenderer that its Tender has been accepted.
3.39.5 Paragraph 3.36 together with the provisions of this paragraph 3.38 will apply with
necessary modifications with respect to the Tenderer notified under sub-paragraph
3.38.4.

3.40 Performance Security


3.40.1 Within fourteen (14) days of the date of notification of award from KPLC, the
successful Tenderer shall furnish KPLC with a Performance Security which shall
be either one or a combination of the following:
a) an original Bank Guarantee that is strictly in the form and content as
prescribed in the Performance Security Form (Bank Guarantee) in the
Tender Document.
b) For Local bidders, Standby Letters of Credit (LC). All costs, expenses and
charges levied by all banks party to the LC shall be prepaid/borne by the
Tenderer. The LC must contain all the mandatory conditions of payment
to KPLC as prescribed in the Tender Security (Letters of Credit) provided
in the Tender Document.

c) For Foreign bidders, Standby Letters of Credit (LC) confirmed by a bank


in Kenya. All costs, expenses and charges levied by all banks party to the
LC including confirmation charges shall be prepaid/borne by the Tenderer.
The LC must contain all the mandatory conditions of payment to KPLC as
prescribed in the Tender Security (Letters of Credit) provided in the
Tender Document.
3.40.2 The Performance Security shall be issued by a commercial bank licensed by the
Central Bank of Kenya. The bank must be located in Kenya.
3.40.3 The Performance Security shall be the sum of ten percent (10%) of the contract
value. It shall be in the currency of the contract price.
3.40.4 KPLC shall seek authentication of the Performance Security from the issuing
bank. It is the responsibility of the successful Tenderer to sensitize its issuing
bank on the need to respond directly and expeditiously to queries from KPLC.
The period for response shall not exceed three (3) days from the date of KPLC’s
For provision of motor and alternator rewinding services off grid power station
25
query. Should there be no conclusive response by the Bank within
this period, such successful Tenderer’s Performance Security may be deemed as
invalid.
3.40.5 Failure of the successful Tenderer to furnish an authentic Performance Security,
the award shall be annulled and the Tender Security forfeited, in which event
KPLC may notify the next lowest evaluated Tenderer that its Tender has been
accepted.
3.40.6 Paragraph 3.38, 3.39 together with the provisions of this paragraph 3.40 will
apply with necessary modifications, and as far as circumstances permit, with
respect to the Tenderer notified under sub-paragraph 3.39.4.

3.41 Corrupt or Fraudulent Practices


3.41.1 KPLC requires that Tenderers observe the highest standard of ethics during the
procurement process and execution of contracts. When used in the present
Regulations, the following terms are defined as follows: -
a) “Corrupt practice” means the offering, giving, receiving or soliciting of
any thing of value to influence the action of public official in the
procurement process or in contract execution;
b) “Fraudulent practice” means a misrepresentation of facts in order to
influence a procurement process or the execution of a contract to the
detriment of KPLC, and includes collusive practice among Tenderers
(prior to or after Tender submission) designed to establish tender prices at
artificial non-competitive levels and to deprive KPLC of the benefits of
free and open competition.

3.41.2 KPLC will nullify its notification of award if it determines that the Tenderer
recommended has engaged in corrupt or fraudulent practices in competing for the
contract in question.
3.41.3 Further, a Tenderer who is found to have indulged in corrupt or fraudulent
practices risks being debarred from participating in public procurement in Kenya.

For provision of motor and alternator rewinding services off grid power station
26

APPENDIX TO INSTRUCTIONS TO TENDERERS

The following information regarding the particulars of the tender shall complement and or
amend the provisions of the Instructions to Tenderers hereinafter abbreviated as ITT.
Wherever there is a conflict between the provisions of the ITT and the Appendix, the
provisions of the Appendix herein shall prevail over those of the ITT.

No. ITT Reference Clause Particulars of Appendix

1. 3.2.1 Eligible Tenderers Open to prequalified bidders.

2. 3.9 (e) Documents Comprising The Tenderer shall submit at least three (3) names
the Tender – List of Previous with full contact as well as physical addresses of
Customers previous customers of similar services and letters from
the previous customers confirming completion of the
contracts on schedule.

3. 3.13.2 (a) Manufacturer’s / Not applicable for this tender.


Principal’s Authorization
4. Sample viewing Sample viewing will be MANDATORY for this tender
and will be conducted at Nairobi South workshop.

Note:
Sample viewing form must be dully filled and signed
by authorized KPLC staff
5. 3.16.2 Warranty – Period of Not applicable for this tender.

6. 3.17.1 Tender Security Not applicable for this tender.

7. 3.40 Performance Bond The bidder will be required to provide a 10%


performance bond of the total award and it should be
from a local recognized bank
8. 3.36.2 Mode of Award of The tender will be awarded to the lowest evaluated
Contract bidder per item.

For provision of motor and alternator rewinding services off grid power station
27

SECTION IV - SCHEDULE OF REQUIREMENTS

Part A - Brief Schedule Of Services Required

1.1 For Provision of provision motor and alternator rewinding services off grid power
station. Tender number KP1/9A.1A/RT/039/18-19.

No. Item Description Qty Performance * Performance Bidder to tick


Act Period OR End Date service of interest
Performance
Start Date
1. Rewinding of 1no. 1 Immediately One Month
500kva perkins genset after after issuance
alternator exciter issuance of of the LPO
armature windings. the LPO
2. Rewinding of 1 1 Immediately One Month
no.500 kva perkins after after issuance
genset alternator field issuance of of the LPO
and armature the LPO
windings
3. Bearing inspection 2 Immediately One Month
and alignment of 2.no after after issuance
500kva alternators issuance of of the LPO
the LPO
4. Bearing and winding 1 Immediately One Month
inspection of 315 kva after after issuance
leroy somer alternator issuance of of the LPO
the LPO
5. Coupling sheets 1 Immediately One Month
replacement for after after issuance
stamford alternator issuance of of the LPO
282kva the LPO

For provision of motor and alternator rewinding services off grid power station
28

SECTION V - PRICE SCHEDULE FOR SERVICES

Part B - Brief Price schedule Of Services Required

No. Item Description Qty Unit Price VAT Total Price


Act Excl.(Ksh) (Ksh)

1. Rewinding of 1no. 500kva perkins genset 1


alternator exciter armature windings.
2. Rewinding of 1 no.500 kva perkins 1
genset alternator field and armature
windings
3. Bearing inspection and alignment of 2.no 2
500kva alternators
4. Bearing and winding inspection of 315 1
kva leroy somer alternator
5. Coupling sheets replacement for stamford 1
alternator 282kva

Total Price VAT Excl. (Ksh)


16% VAT
Total Price VAT Incl. (Ksh)

Date:

Tender Number and Name:

To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

Dear Sirs and Madams,

Having read, examined and understood the Tender Document including all Addenda,
receipt of which we hereby acknowledge, we, the undersigned Tenderer, offer to provide
……………………(insert services description) for the sum of………………………(total
tender price in words and figures) or such other sums as may be ascertained in
accordance with the schedule of prices inserted by me/ us above.

For provision of motor and alternator rewinding services off grid power station
29
Name of Tenderer

_____________________

Name and Designation of authorised person signing the Tender

___________________________________

Signature of authorised person signing the Tender

__________________________________

Stamp of Tenderer

__________________________________

For provision of motor and alternator rewinding services off grid power station
30

SECTION VI - EVALUATION CRITERIA

Evaluation of duly submitted tenders will be conducted along the following stages: -

6.1 Part 1 - Preliminary Evaluation Under Paragraph 3.28 of the ITT. These are
mandatory requirements. This shall include confirmation of the following:-

6.1.1 Submission of Declaration Form(s) duly completed and signed.


6.1.2 Submission and considering Tender Form duly completed and signed.
6.1.3 Submission and considering the following:-
6.1.3.1 For Local Tenderers
a) Company or Firm’s Registration Certificate
b) PIN Certificate.
c) Valid Tax Compliance Certificate.
6.1.3.2 For Foreign Tenderers
a) Company or Firm’s Registration Certificate
b) PIN Certificate or its equivalent in the country of bidder or
a statement from the tax authorities in the Tenderer’s
country of origin indicating that such certificate or its
equivalent is not issued.
c) Valid Tax Compliance Certificate or its equivalent in the
country of bidder or a statement from the tax authorities in
the Tenderer’s country of origin indicating that such
certificate or its equivalent is not issued.
6.1.4 That the Tender is valid for the period required.
6.1.5 Submission and considering the Confidential Business Questionnaire:-
a) Is fully filled.
b) That details correspond to the related information in the bid.
c) That the Tenderer is not ineligible as per paragraph 3.2 of the ITT.

6.1.6 Record of unsatisfactory or default in performance obligations in any contract


shall be considered. This shall include any Tenderer with unresolved case(s) in its
performance obligations for more than two (2) months in any contract.

For provision of motor and alternator rewinding services off grid power station
31
6.2 Part II – Technical Evaluation and Comparison of Tenders Under
Paragraph 3.30 of the ITT. These are mandatory requirements.

6.2.1 Verification of the following information:

a) Sample viewing form dully filled signed by KPLC authorized staff

b) The Tenderer shall submit at least three (3) names with full contact as
well as physical addresses of previous customers of similar services and
letters from the previous customers confirming completion of the contracts
on schedule.

6.3 Part III – Financial Evaluation Criteria Under Paragraph 3.31 of the ITT.
These are mandatory requirements.

6.3.1 This will include the following: -


a) Confirmation of and considering Price Schedule duly completed and
signed.
c) Checking that the Tenderer has quoted prices based on all costs including
duties and taxes

6.3.2 Confirming the following: -


6.3.2.1 that the Supplier’s offered Delivery Schedule meets KPLC’s requirements.
6.3.2.2 that the Supplier’s offered Terms of Payment meets KPLC’s requirements.

*NOTES: -
1. For purposes of evaluation, the exchange rate to be used for currency conversion
shall be the selling exchange rate prevailing on the date of tender closing provided
by the Central Bank of Kenya. (Visit the Central Bank of Kenya website).

2. Total tender value means the Tenderer’s total tender price inclusive of Value
Added Tax (V.A.T) for the services it offers to provide.

3. For companies or firms that are registered or incorporated within the last one
calendar year of the Date of the Tender Document, they should submit certified
copies of bank statements covering a period of at least six months prior to the date
of the tender document. The copies should be certified by the Bank issuing the
statements. The certification should be original.

For provision of motor and alternator rewinding services off grid power station
32

TABLE OF CLAUSES ON GENERAL CONDITIONS OF CONTRACT

Clause No. Headings Page No.

7.1 Definitions……..……………………………………………. 33
7.2 Application…. ……………………………………………… 34
7.3 Standards……………………………………………………..34
7.4 Use of Contract Documents and Information………………..34
7.5 Patent Rights………………. ………………………………..35
7.6 Performance Security………………..……………………….35
7.7 Inspections and Tests…………………………………………36
7.8 Packaging and Labelling …………………………………….36
7.9 Delivery and Documents for Materials/ Equipment………….37
7.10 Insurance ……..………………………………………………37
7.11 Payment……………………………… ………………………37
7.12 Interest………………………………………………………. 38
7.13 Prices………………………………………………………….38
7.14 Variation of Contract………………………………………....39
7.15 Assignment…..……………………………………………….39
7.16 Sub-Contracts……..………………………………………….39
7.17 Termination of Contract………....……………………………39
7.18 Liquidated Damages…………..……………………………...40
7.19 Warranty………………………………………………………40
7.20 Resolution of Disputes ……………..………………………..41
7.21 Language and Law……………………..…………………….41
7.22 Waiver………………..………………………………………41
7.23 Force Majeure………………………………………………..41

For provision of motor and alternator rewinding services off grid power station
33

SECTION VII – GENERAL CONDITIONS OF CONTRACT

The General Conditions of Contract hereinafter referred abbreviated as the GCC shall
form part of the Conditions of Contract in accordance with the law and KPLC’s
guidelines, practices, procedures and working circumstances. The provisions in the GCC
will apply unless an alternative solution or amendment is made under other parts of the
Contract including the Special Conditions of Contract.

7.1 Definitions
In this contract, the following terms shall be interpreted as follows: -
a) “Day” means calendar day and “month” means calendar month.
b) “The Contract” means the agreements entered into between KPLC and
the Contractor, as recorded in the Contract Form signed by the parties,
including all attachments and appendices thereto and all documents
incorporated by reference therein.
c) “The Contract Price” means the price payable to the Contractor under
the contract for the full and proper performance of its contractual
obligations.
d) “The Services” means services or art thereof to be provided by the
Contractor and includes all of the materials and incidentals, which the
Contractor is required to perform and provide to KPLC under the
contract.
e) “The Procuring Entity” means The Kenya Power and Lighting Company
Limited or its successor(s) and assign(s) where the context so admits
(hereinafter abbreviated as KPLC).
f) “The Contractor” means the individual or firm providing the services
under this contract or his/ her/ its permitted heir(s), personal
representative(s), successor(s) or permitted assign(s) where the context so
admits. For the avoidance of doubt this shall mean the successful
Tenderer(s) pursuant to the tender.
g) Wherever used in the contract, “performance” shall be complete or be
deemed to be complete, unless the circumstances indicate otherwise, when
the services have been performed in accordance with the Contract and
where KPLC does not signify its approval to the Contractor, but without
giving notice of dissatisfaction, on the expiration of thirty (30) days from
date of documented completion of performance of the service.
h) Supplier Rating Performance Scheme (SPRS) means the continuous
evaluation of the Supplier’s performance of the contract based on the
parameters of timely delivery, quality of service, frequency of
communication, timely response, innovation, dispute resolution.
For provision of motor and alternator rewinding services off grid power station
34

7.2 Application
These General Conditions shall apply to the extent that provisions of other parts
of the contract do not supersede them.

7.3 Standards
The Services supplied under this contract shall conform to the standards
mentioned in the Details of Service.

7.6 Supplier Performance Rating Scheme


7.6.1 KPLC shall use a Supplier Performance Rating Scheme (SPRS) to measure the
annual performance of the Supplier’s obligations and its conduct of the contract.
7.6.2 The Scheme will be updated periodically commencing with the date of execution
of the contract by both parties. KPLC shall provide the Supplier with a copy of
the SPRS report.
7.6.3 KPLC shall consider the Supplier’s overall performance at the end of the
performance period.
7.6.4 At the request of either party, the parties shall discuss and conclude deliberations
on the annual SPRS report. At any such meetings and/or for the purposes of the
deliberations, KPLC Supply Chain – Procurement Department shall appoint the
Chairperson as well as the Secretariat.
7.6.5 The SPRS measures shall be according to Supplier Performance Rating Form in
Section XXVI
7.6.6 A KP1, KP2 & KP3 assessment of the Supplier on the SPRS will be a
consideration for continued engagement between the parties in the subsequent
year. A KP4 assessment of the Supplier shall be a termination event.

7.4 Use of Contract Documents and Information


7.4.1 The Contractor shall not, without KPLC’s prior written consent, disclose the
contract, or any provision thereof or any specification, plan, drawing, pattern,
sample, or information furnished by or on behalf of KPLC in connection
therewith, to any person other than a person employed by the Contractor in the
performance of the contract.
7.4.2 The Contractor shall not, without KPLC’s prior written consent, make use of any
document or information enumerated in clause 7.4.1 above.
7.4.3 Any document, other than the contract itself, enumerated in clause 7.4.1 shall
remain the property of KPLC and shall be returned (including all copies) to KPLC
on completion of the Contractor’s performance under the contract if so required
by KPLC.

For provision of motor and alternator rewinding services off grid power station
35
7.5 Patent Rights
The Contractor shall indemnify KPLC against all third party claims of
infringement of patent, trademark, or industrial design rights arising from
provision of the services or any part thereof.

7.6 Performance Security


7.6.1 Within fourteen (14) days of the date of the notification of contract award, the
Contractor shall furnish to KPLC the Performance Security which shall be either
one or a combination of the following: -
a) an original Bank Guarantee that is strictly in the form and content as
prescribed in the Performance Security Form (Bank Guarantee) in the
Tender Document.
b) Confirmed Standby Letters of Credit (LC). All costs, expenses and
charges levied by all banks party to the LC including confirmation charges
shall be prepaid by the successful Tenderer. Certain mandatory conditions
of the LC shall be as prescribed in the Performance Security Form (LC) in
the Tender Document.
7.6.2 The Performance Security shall be issued by a commercial bank licensed by the
Central Bank of Kenya. The bank must be located in Kenya.
7.6.3 The Performance Security shall be the sum of ten percent (10%) of the contract
price. It shall be in the currency of the contract price.
7.6.4 Failure of the Contractor to furnish the Performance Security, the award shall be
annulled and the Tender Security forfeited, in which event KPLC may notify the
next lowest evaluated Tenderer that its Tender has been accepted.
7.6.5 The proceeds of the Performance Security shall be payable to KPLC as
compensation for any loss resulting from the Contractor’s failure to comply with
its obligations in accordance with the contract without KPLC being required to
demonstrate the loss it has suffered.
7.6.6 The Performance Security shall be valid for a minimum of sixty (60) days after
satisfactory delivery for both Foreign and Local Contractors.
7.6.7 KPLC shall seek authentication of the Performance Security from the issuing
bank. It is the responsibility of the Contractor to sensitize its issuing bank on the
need to respond directly and expeditiously to queries from KPLC. The period for
response shall not exceed three (3) days from the date of KPLC’s query. Should
there be no conclusive response by the Bank within this period, such Contractor’s
Performance Security may be deemed as invalid and the Contract nullified, unless
information to the contrary is received by KPLC two (2) days before the expiry of
the Contractor’s Tender Security.
7.6.8 Subject to the provisions of this contract, the Performance Security will be
discharged by KPLC and returned to the Contractor not earlier than thirty (30)

For provision of motor and alternator rewinding services off grid power station
36
days following the date of completion of the Contractor’s obligations
under the contract, including any warranty obligations, under the contract.

7.7 Inspection and Tests


7.7.1 KPLC or its representative(s) shall have the right to inspect and/or to test the
services to confirm their conformity to the contract specifications. KPLC shall
notify the Contractor in writing in a timely manner, of the identity of any
representative(s) retained for these purposes. Such visit and or inspection/ test
shall in no way prejudice KPLC’s rights and privileges.
7.7.2 In appropriate circumstances, Inspection/ Test Report(s) shall be completed upon
conclusion of the inspection/ tests.
7.7.3 The inspections and tests may be conducted in the premises of the Contractor or
its subcontractor(s). If conducted on the premises of the Contractor or its
subcontractor(s), all reasonable facilities and assistance, including access to
drawings and production data, shall be furnished to the inspectors at no charge to
KPLC.
7.7.4 Should any inspected or tested services fail to conform to the specifications,
KPLC may reject the Service(s), and the Contractor shall either replace or remedy
the rejected services or make alterations necessary to meet specification
requirements free of cost to KPLC.
7.7.5 KPLC’s right to inspect, test and where necessary, reject the services after
provision shall in no way be limited or waived by reason of the services having
previously been inspected, tested and passed by KPLC or its representative(s)

prior to the services performance / delivery.


7.7.6 For the avoidance of doubt, any acknowledgement by KPLC on the Contractor’s
or sub-contractor’s document shall not be conclusive proof or evidence of
satisfactory performance without duly authorized approval by KPLC.
7.7.7 Nothing in this clause 7.7 shall in any way release the Contractor from any
warranty or other obligations under this Contract.

7.8 Packaging and Labelling


7.8.1 Where applicable, the Contractor shall provide such packaging of the material and
equipment as is required to prevent their damage or deterioration during transit to
their final destination, as indicated in the contract.
7.8.2 The method of packaging, labeling and marking shall comply strictly with such
special requirements as shall be specified and attached to the Contract and
particular Order.
7.8.3 The labelling, marking and documentation within and outside the packages shall
comply strictly with such special requirements as shall be expressly provided for
in the contract.
For provision of motor and alternator rewinding services off grid power station
37
7.8.4 The materials and equipment shall be packed in good condition suitable for
sea/air/road/rail dispatch. Hazard in transit to the final destination shall include
rough handling and storage in tropical conditions.
7.8.5 The Contractor shall enclose a packing list in each package and all documents
relating to the Order shall show the Tender reference number and name against
the items or package indicating the supplier or supplier’s agent as the consignee.

7.9 Delivery and Documents for Materials/ Equipment


7.9.1 Where applicable, delivery of the materials/ equipment shall be made by the
Contractor to the place and in accordance with the terms specified by KPLC in its
Schedule of Requirements or as may be otherwise indicated.
7.9.2 The Contractor shall notify KPLC of the full details of the delivered materials/
equipment by delivering the materials/ equipment with a full set of the following
documents: -

a) Contractor’s invoice showing the materials/ equipment description,


quantity, unit price and total price
b) Delivery note
c) Packing list identifying contents of each package

7.9.3 It is the responsibility of the Contractor to ensure that the delivery documents are
received by KPLC at the designated delivery point at the time of delivery.

7.10 Insurance
7.10.1 The Contractor shall be responsible for and keep in force current appropriate
insurance covers for its property and persons engaged in the performance and or
provision of the Services under the contract.
7.10.2 The Contractor shall (except in respect to losses, injuries or damage resulting from
any act or neglect of KPLC) indemnify and keep indemnified KPLC against all
losses and claims for injuries or damage to any person or property whatsoever
which may arise out of or in consequence of the contract and against all claims,
demands, proceedings, damages, costs, charges, and expenses whatsoever in
respect thereof or in relation thereto.

7.11 Payment
7.11.1 Payments shall be made promptly by KPLC and shall not be less than thirty (30)
days from completion of satisfactory performance and submission of invoice
together with other required and related documents or as otherwise prescribed in
the contract.
7.11.2 Payment shall primarily be through KPLC’s cheque or Real Time Gross
Settlement (RTGS) or telegraphic transfer. Where applicable, a copy of a valid
For provision of motor and alternator rewinding services off grid power station
38
Performance Security, stamped, certified as authentic by KPLC, shall form
part of the documents to be presented to KPLC before any payment is made.
7.11.3 A Contractor who requests for a Letter of Credit (hereinafter abbreviated as LC)–
a) Shall meet the LC bank charges levied by its bank while KPLC shall meet
the LC bank charges levied by its bank.
b) Any extension and or amendment charges and any other costs that may
result from the Contractor’s delays, requests, mistakes or occasioned
howsoever by the Contractor shall be to the Beneficiary’s account.
c) The maximum number of extensions and amendments shall be limited to
two (2).
d) Notwithstanding sub-clause 7.11.3 (a), should the Contractor require a
confirmed LC, then all confirmation and any other related charges levied
by both the Contractor’s and KPLC’s bank shall be to the Beneficiary’s
account.
e) The LC shall be opened only for the specific Order within the validity
period of the contract.
f) LCs shall be partial for partial performance or full for whole performance
as per the contract.
g) The Contractor shall be required to submit a proforma invoice for each lot

for use in the placement of order and opening of the LC. The proforma
invoice shall be on total all-inclusive costs basis.
h) A copy of the Performance Security, stamped and certified as authentic by
KPLC, whose expiry date should not be less than sixty (60) days from the
LC expiry date, shall form part of the documents to be presented to the
Bank before any payment is affected.
7.11.4 KPLC shall have the sole discretion to accept or decline any Contractor’s
payment request through Letters of Credit without giving any reason for any
decline.

7.12 Interest
Interest payment by KPLC is inapplicable in the contract.

7.13 Prices
7.13.1 Subject to clause 7.14 herein below, prices charged by the Contractor for services
performed under the contract shall be fixed for the period of the contract with no
variations.
7.13.2 A price that is derived by a pre-disclosed incorporation or usage of an
internationally accepted standard formula shall not be deemed to be a price
variation within the meaning of this clause.

For provision of motor and alternator rewinding services off grid power station
39
7.14 Variation of Contract
KPLC and the Supplier may vary the contract only in accordance with the
following: -
a) the quantity variation of services shall not exceed twenty percent (20%) of
the original contract quantity.
b) The cumulative value variation shall not exceed twenty-five percent (25%)
of the original contract value.
c) the quantity variation must be executed within the period of the contract.

7.15 Assignment
The Contractor shall not assign in whole or in part its obligations to perform
under this contract, except with KPLC’s prior written consent.

7.16 Subcontracts
7.16.1 The Contractor shall notify KPLC in writing of all subcontracts awards under this
contract if not already specified in the tender. Such notification, in the original
tender or obligation under the Contract shall not relieve the Contractor from any
liability or obligation under the Contract.
7.16.2 In the event that an award is given and the contract is sub-contracted, the
responsibility and onus over the contract shall rest on the Contractor who was
awarded.

7.17 Termination of Contract


7.17.1 KPLC may, without prejudice to any other remedy for breach of contract, by
written notice sent to the Contractor, terminate this contract in whole or in part
due to any of the following: -
a) if the Contractor fails to perform any or all of the services within the
period(s) specified in the contract, or within any extension thereof granted
by KPLC.
b) if the Contractor fails to perform any other obligation(s) under the
contract.
c) if the Contractor, in the judgment of KPLC has engaged in corrupt or
fraudulent practices in competing for or in executing the contract.
d) by an act of force majeure.
e) if the Contractor becomes insolvent or bankrupt
f) if the Contractor has a receiving order issued against it, compounds with
its creditors, or an order is made for its winding up (except for the
purposes of its amalgamation or reconstruction), or a receiver is
appointed over its or any part of its undertaking or assets, or if the
Contractor suffers any other analogous action in consequence of debt.
For provision of motor and alternator rewinding services off grid power station
40
g) if the Contractor abandons or repudiates the Contract.

7.17.2 In the event that KPLC terminates the contract in whole or in part, it may procure,
upon such terms and in such manner as it deems appropriate, services similar to
those undelivered or not rendered, and the Contractor shall be liable to KPLC for
any excess costs for such similar services and or any other loss PROVIDED that
the Contractor shall not be so liable where the termination is for convenience of
KPLC.
7.17.3 The Parties may terminate the Contract by reason of an act of force majeure as
provided for in the contract.
7.17.4 The Contract may automatically terminate by reason of an act of force majeure as
provided for in the Contract.

7.18 Liquidated Damages


Notwithstanding and without prejudice to any other provisions of the contract, if
the Contractor fails to perform any or all of the services within the period
specified in the contract, KPLC shall, without prejudice to its other remedies
under the contract, deduct from the contract prices, liquidated damages sum
equivalent to 0.5% of the performance price per day of delay of the delayed due
services up to a maximum of ten percent (10%) of the performance price of the
delayed due services.

7.19 Warranty
7.19.1 Where applicable, the Contractor warrants that the Services provided under the
contract are of the highest quality or current specification and incorporate all
recent improvements unless provided otherwise in the contract. The Contractor
further warrants that any materials/ equipment provided under this contract shall
have no defect arising from manufacture, materials or workmanship or from any
act or omission of the Contractor that may develop under normal use of the
materials/ equipment provided under the conditions obtaining in Kenya.
7.19.2 This warranty will remain valid for the period indicated in the special conditions
of contract after the goods, or any portion thereof as the case may be, have been
delivered to the final destination indicated in the contract.
7.19.3 KPLC shall promptly notify the Contractor in writing of any claims arising under
this Warranty.
7.19.4 Upon receipt of such a notice, the Contractor shall, with all reasonable speed,
remedy the defective services without cost to KPLC.
7.19.5 If the Contractor having been notified, fails to remedy the defect(s) within a
reasonable period, KPLC may proceed to take such remedial action as may be
necessary, at the Contractor’s risk and expense and without prejudice to any other
rights which KPLC may have against the Contractor under the contract.
For provision of motor and alternator rewinding services off grid power station
41

7.20 Resolution of Disputes


7.20.1 KPLC and the Contractor may make every effort to resolve amicably by direct
informal negotiation any disagreement or dispute arising between them under or
in connection with the contract.
7.20.2 If, after thirty (30) days from the commencement of such informal negotiations
both parties have been unable to resolve amicably a contract dispute, either party
may resort to resolution before a recognized local forum for the resolution of
disputes.

7.21 Language and Law


The language of the contract and the law governing the contract shall be the
English language and the laws of Kenya respectively unless otherwise stated.

7.22 Waiver
Any omission or failure by KPLC to exercise any of its rights or enforce any of
the penalties arising from the obligations imposed on the Contractor shall in no
way, manner or otherwise howsoever, alter, amend, prejudice, vary, waive or be
deemed to alter, amend, prejudice, vary, waive or otherwise whatsoever any of
KPLC’s powers and rights as expressly provided in and as regards this contract.

7.23 Force Majeure


7.23.1 Force majeure means any circumstances beyond the control of the parties,
including but not limited to:
a) war and other hostilities (whether war be declared or not), invasion, act of
foreign enemies, mobilization, requisition or embargo;
b) ionizing radiation or contamination by radio-activity from any nuclear
fuel or from any nuclear waste from the combustion of nuclear fuel,
radioactive toxic explosives or other hazardous properties of any
explosive nuclear assembly or nuclear components thereof;
c) rebellion, revolution, insurrection, military or usurped power & civil war;
d) riot, commotion or disorder except where solely restricted to employee’s
servants or agents of the parties;
e) un-navigable storm or tempest at sea.
7.23.2 Notwithstanding the provisions of the contract, neither party shall be considered
to be in default or in breach of its obligations under the Contract to the extent that
performance of such obligations is prevented by any circumstances of force
majeure which arise after the contract is entered into by the parties.
7.23.3 If either party considers that any circumstances of force majeure are occurring or
have occurred which may affect performance of its obligations it shall promptly
notify the other party and provide reasonable proof of such circumstances.
For provision of motor and alternator rewinding services off grid power station
42
7.23.4 Upon the occurrence of any circumstances of force majeure, the
Contractor shall endeavour to continue to perform its obligations under the
contract so far as is reasonably practicable. The Contractor shall notify KPLC of
the steps it proposes to take including any reasonable alternative means for
performance, which is not prevented by force majeure. The Contractor shall not
take any such steps unless directed so to do by KPLC.
7.23.5 If the Contractor incurs additional costs in complying with KPLC’s directions
under sub clause 7.23.4, then notwithstanding the provisions of the contract, the
amount thereof shall be agreed upon with KPLC and added to the contract price.
7.23.6 If circumstances of force majeure have occurred and shall continue for a period of
twenty-one (21) days then, notwithstanding that the Contractor may by reason
thereof have been granted an extension of time for performance of the contract,
either party shall be entitled to serve upon the other seven (7) days’ notice to
terminate the contract. If at the expiry of the period of twenty-eight (28) days,
force majeure shall still continue, the contract shall terminate.

For provision of motor and alternator rewinding services off grid power station
43

SECTION VIII – SPECIAL CONDITIONS OF CONTRACT

The Special Conditions of Contract hereinafter abbreviated as SCC shall form part of the
Conditions of Contract. They are made in accordance with the law and KPLC’s
guidelines, practices, procedures and working circumstances. They shall amend, add to
and vary the GCC. The clauses in this section need not therefore, be completed but must
be completed by KPLC if any changes to the GCC provisions are deemed necessary.
Whenever there is a conflict between the GCC and SCC, the provisions of the SCC shall
prevail over those in the GCC.

No. GCC Reference Clause Particulars of SCC

1. 7.11.1 Terms of Payment The credit period shall be thirty (30) days from
satisfactory delivery and submission of invoice together
with other required and related documents.

For provision of motor and alternator rewinding services off grid power station
44

SECTION IX - TENDER FORM

Date:
Tender No.
To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

Ladies and Gentlemen,

1. Having read, examined and understood the Tender Document including all Addenda,
the receipt of which is hereby duly acknowledged, we, the undersigned Tenderer,
offer to perform, deliver, install and commission (the latter two where applicable)
………………………………………. (insert services description) in accordance and
conformity with the said tender document and in particular the Schedule of Prices that
are made part of this Tender.

2. We undertake, if our Tender is accepted, to perform and provide the services in


accordance with the Schedule of Requirements.

3. If our Tender is accepted, we will obtain the guarantee of a bank in a sum of


equivalent to ten percent (10%) of the contract price for the due performance of the
contract, in the form(s) prescribed by The Kenya Power & Lighting Company
Limited.

4. We agree to abide by this Tender for a period of………days (Tenderer please


indicate validity of your Tender) from the date fixed for tender opening as per the
Tender Document, and it shall remain binding upon us and may be accepted at any
time before the expiration of that period.

5. This Tender, together with your written acceptance thereof and your notification of
award, shall not constitute a contract, between us. The contract shall be formed
between us when both parties duly sign the written contract.

6. We understand that you are not bound to accept any Tender you may receive.

For provision of motor and alternator rewinding services off grid power station
45
Yours sincerely,

_____________________
Name of Tenderer

___________________________________
Signature of duly authorized person signing the Tender

__________________________________
Name and Designation of duly authorized person signing the Tender

__________________________________
Stamp or Seal of Tenderer

*NOTES:

1. KPLC requires a validity period of at least one hundred and twenty (120) days.
2. This form must be duly signed, stamped and/or sealed.

For provision of motor and alternator rewinding services off grid power station
46

SECTION X - CONFIDENTIAL BUSINESS QUESTIONNAIRE FORM

All Tenderers are requested to give the particulars indicated in Part 1 and either Part 2
(a), 2 (b) or 2 (c), whichever applies to your type of business. You are advised that it is a
serious offence to give false information on this form.

Part 1 – General
Business Name…………………………………………………………………

Location of business premises…………………………………………………

Plot No. ……………………Street/ Road ………………………………..

Postal Address ………………………….. Postal Code …………………….

Tel No………………………………..

Facsimile..………………………………..

Mobile and/ or CDMA No……………………….

E-mail:…………………………………………………

Nature of your business ………………………………………………………………..


Registration Certificate No.……………………………………………………

Maximum value of business which you can handle at any time KSh………….

Name of your Bankers …………………………..Branch… ………………

*Names of Tenderer’s contact person(s) ………………………….

Designation of the Tenderer’s contact person(s) ………………………………

Address, Tel, Fax and E-mail of the Tenderer’s contact person(s) ……………….
……………………………………………………………………………………...
……………………………………………………………………………………

For provision of motor and alternator rewinding services off grid power station
47

Part 2 (a) Sole Proprietor


Your name in full ………………………………………………………………….
Nationality ………………………Country of origin …………………………..
*Citizenship details………………………………………………………………….

Part 2 (b) Partnership


Give details of partners as follows: -
Names Nationality *Citizenship Details Shares
1.…………………………………………………………………………
2.…………………………………………………………………………
3….………………………………………………………………………
4.………………………………………………………………………….
5………………………………………………………………………….

Part 2 (c) Registered Company


Private or Public …………………………………………………………………….
State the nominal and issued capital of company-
Nominal KSh.……………………………………
Issued KSh……………………………………
Give details of all directors as follows
Name Nationality *Citizenship Details Shares
1……………………………………………………………………………………….

2……………………………………………………………………………………….

3………………………………………………………………………………………..

4………………………………………………………………………………………..

5………………………………………………………………………………………..

Name of duly authorized person to sign for and on behalf of the Tenderer
………………………………………………..………………………..

Designation of the duly authorized person……………………………………

Signature of the duly authorized person……………………………..

For provision of motor and alternator rewinding services off grid power station
48

*NOTES TO THE TENDERERS ON THE QUESTIONNAIRE

1. The address and contact person of the Tenderer provided above shall at all times
be used for purposes of this tender.
2. If a Kenyan citizen, please indicate under “Citizenship Details” whether by birth,
naturalization or registration.
3. The details on this Form are essential and compulsory for all Tenderers. Failure
to provide all the information requested shall lead to the Tenderer’s
disqualification.
4. For foreign Tenderers please give the details of nominal and issued share capital
in the currency of the country of origin of the Tenderer.

For provision of motor and alternator rewinding services off grid power station
49

SECTION XI A - TENDER SECURITY FORM – (BANK GUARANTEE)

(To Be Submitted On Bank’s Letterhead) Date:

To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

WHEREAS ……………………………………… (name of the Tenderer) (hereinafter


called “the Tenderer”) has submitted its Tender dated ……… for the supply, installation
and commissioning of………………………… (please insert KPLC tender no. and
name) (hereinafter called “the Tender”);

KNOW ALL PEOPLE by these presents that WE………………………………….of


…………………………….having our registered office
at…………………….(hereinafter called “the Bank”), are bound unto The Kenya Power
and Lighting Company Limited (hereinafter called “KPLC” which expression shall
where the context so admits include its successors-in-title and assigns) in the sum of
…………………………………. for which payment well and truly to be made to the said
KPLC, the Bank binds itself, its successors, and assignees by these presents.

We undertake to pay you, upon your first written demand declaring the Tenderer to be in
breach of the tender requirements and without cavil or argument, the entire sum of this
guarantee being …………………….. (amount of guarantee) as aforesaid, without you
needing to prove or to show grounds or reasons for your demand or the sum specified
therein.

This tender guarantee will remain in force up to and including thirty (30) days after the
period of tender validity, and any demand in respect thereof should reach the Bank not
later than the date below.

This guarantee is valid until the …..…day of………………………20……

EITHER

SEALED with the )


COMMON SEAL )
For provision of motor and alternator rewinding services off grid power station
50

of the said BANK ) _______________________________


this ……………………day ) BANK SEAL
of ………………………20…. )
)
in the presence of :- )
)
____________________ )
)
and in the presence of:- )
)
__________________ )

OR

SIGNED by the DULY AUTHORISED


REPRESENTATIVE(S)/ ATTORNEY(S) of
the BANK

_____________________
Name(s) and Designation of duly authorised representative(s)/ attorney(s) of the Bank

___________________________________
Signature(s) of the duly authorised person(s)

NOTES TO TENDERERS AND BANKS

1. Please note that no material additions, deletions or alterations regarding the


contents of this Form shall be made to the Tender Security to be furnished by the
Tenderer. If any are made, the Tender Security shall not be accepted and shall be
rejected by KPLC. For the avoidance of doubt, such rejection will be treated as
non-submission of the Tender Security where such Security is required in the
tender.

2. It is the responsibility of the Tenderer to sensitize its issuing bank on the need to
respond directly and expeditiously to queries from KPLC. The period for response
shall not exceed three (3) days from the date of KPLC’s query. Should there be no
conclusive response by the Bank within this period, such Tenderer’s Tender
Security shall be deemed as invalid and the bid rejected.

For provision of motor and alternator rewinding services off grid power station
51

3. The issuing bank should address its response or communication regarding the
bond to KPLC at the following e-mail address – “guarantees@ kplc.co.ke”

4. The Tender validity period is one hundred and twenty (120) days as set out in the
Invitation to Tender (at Section I of the Tender document) or as otherwise may be
extended by KPLC. Therefore the Tender Security must at all times be valid for at
least 30 days beyond the tender validity period.

For provision of motor and alternator rewinding services off grid power station
52

SECTION XI B - TENDER SECURITY FORM (SACCO SOCIETY, DEPOSIT


TAKING MICRO FINANCE INSTITUTIONS, WOMEN ENTERPRISE FUND &
YOUTH ENTERPRISE FUND)

(To Be Submitted On Institutions Letterhead) Date:

To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

WHEREAS…………………………(hereinafter called “the Contractor”) has


undertaken, in pursuance of your Tender Number………………..(reference number of
the Tender) and its Tender dated ………………(insert Contractor’s date of Tender taken
from the Tender Form) to supply ……………(description of the Works) (hereinafter
called “the Contract);

AND WHEREAS it has been stipulated by you in the said Contract that the Contractor
shall furnish you with an Institution’s guarantee by an acceptable Institution for the sum
specified therein as security for compliance of the Contractor’s performance obligations
in accordance with the Contract;

AND WHEREAS we have agreed to give the Contractor a Guarantee;

THEREFORE, WE HEREBY AFFIRM that we are Guarantors and responsible to


you, on behalf of the Contractor, up to a total of……………………. (amount of the
guarantee in words and figures) and we undertake to pay you, upon your first written
demand declaring the Contractor to be in default under the Contract and without cavil or
argument, any sum or sums within the limits of ………………………………………...
(amount of guarantee) as aforesaid, without you needing to prove or to show grounds or
reasons for your demand or the sum specified therein.

This guarantee is valid until the …………day of……………….…..…20….

EITHER
SEALED with the )
COMMON SEAL )
of the said INSTITUTION )

For provision of motor and alternator rewinding services off grid power station
53

this ……………………day ) _____________________________


) INSTITUTION SEAL
of ………………………20…. )
in the presence of :- )
)
____________________ )
)
and in the presence of:- )
)
__________________ )

OR

SIGNED by the DULY AUTHORISED


REPRESENTATIVE(S)/ ATTORNEY(S) of
the INSTITUTION

_____________________
Name(s) and Designation of duly authorised representative(s)/ attorney(s) of the
Institution.

___________________________________
Signature(s) of the duly authorised person(s)

NOTES TO SUPPLIERS AND INSTITUTIONS

1. Please note that no material additions, deletions or alterations regarding the


contents of this Form shall be made to the Tender Security to be furnished by the
Tenderer. If any are made, the Tender Security shall not be accepted and shall be
rejected by KPLC. For the avoidance of doubt, such rejection will be treated as
non-submission of the Tender Security where such Security is required in the
tender.

2. It is the responsibility of the Tenderer to sensitize its issuing institution on the


need to respond directly and expeditiously to queries from KPLC. The period for
response shall not exceed three (3) days from the date of KPLC’s query. Should

For provision of motor and alternator rewinding services off grid power station
54
there be no conclusive response by the institution within this period, such
Tenderer’s Tender Security shall be deemed as invalid and the bid rejected.

3. The issuing institution should address its response or communication regarding


the Tender Security to KPLC at the following e-mail address – “guarantees@
kplc.co.ke”

4. The Tender validity period is one hundred and twenty (120) days as set out in the
Invitation to Tender (at Section I of the Tender document) or as otherwise may be
extended by KPLC. Therefore the Tender Security must at all times be valid for at
least 30 days beyond the tender validity period.

For provision of motor and alternator rewinding services off grid power station
55

SECTION XI C - TENDER SECURITY – (LETTERS OF CREDIT)

The Mandatory Conditions to be included in the Letters are in two parts, A and B.

Part A

Form of Documentary credit - “Irrevocable Standby”

Applicable rules - “Must be UCP Latest Version” i.e. UCP 600 (2007 REVISION) ICC
Publication No. 600.

Place of expiry - At the counters of the advising bank.

The SBLC should be available – “By Payment”

Drafts should be payable at - “SIGHT”

Documents required -
1. Beneficiary’s signed and dated statement demanding for payment under the letter of
credit no………………………….. (Insert LC No.) as……………………….(Name of
applicant) (hereinafter called the “Tenderer”) indicating that the “Tenderer” has
defaulted in the obligations of the Tenderer as stated by the Beneficiary.

2. The Original Letter of Credit and all amendments, if any.

Additional Conditions -
1. All charges levied by any bank that is party to this documentary credit are for the
account of the applicant.

2. There should be no conditions requiring compliance with the specific regulations or a


particular country’s Law and regulations.

Charges - All bank charges are for the account of the applicant.

*Confirmation instructions – (See notes below)

Part B
The proceeds of these Letters are payable to KPLC -
a) if the Tenderer withdraws its Tender after the deadline for submitting Tenders but
before the expiry of the period during which the Tenders must remain valid.
b) if the Tenderer fails to enter into a written contract in accordance with the Tender
Document
c) if the successful Tenderer fails to furnish the performance security in accordance
with the Tender Document.

For provision of motor and alternator rewinding services off grid power station
56

d) if the Tenderer fails to extend the validity of the tender security where KPLC has
extended the tender validity period in accordance with the Tender Document.

NOTES TO TENDERERS AND BANKS.

1. Please note that should the Tender Security (LC) omit any of the above conditions
the LC shall not be accepted and shall be rejected by KPLC. For the avoidance of
doubt, such rejection will be treated as non-submission of the LC where such LC
is required in the Tender.

2. It is the responsibility of the Tenderer to sensitize its issuing bank on the need to
respond directly and expeditiously to any queries from KPLC. The period for
response shall not three (3) days from the date of KPLC’s query. Should there be
no conclusive response by the Bank within this period, such Tenderer’s Tender
Security shall be deemed as invalid and the bid rejected.

3. The issuing bank should address its response or communication regarding the
bond to KPLC at the following e-mail address – “guarantees@ kplc.co.ke”

4. The Tender validity period is ninety (90) days as set out in the Invitation to
Tender (at Section I of the Tender document) or as otherwise may be extended by
KPLC. Therefore the Tender Security must at all times be valid for at least 30
days beyond the tender validity period.

5. All Guarantees issued by foreign banks must be confirmed by a local bank in


Kenya.

For provision of motor and alternator rewinding services off grid power station
57

SECTION XII - MANUFACTURER’S/ PRINCIPAL’S AUTHORIZATION FORM

(To Be Submitted On Manufacturer’s/ Principal’s/ Producer’s Letterhead)

To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

WHEREAS WE ……………………………(name of the manufacturer/ principal) who


are established and reputable manufacturers/ principal of …………………………
(name and description of the services) having offices or factories at ……………(full
address and physical location of offices or factory(ies) do hereby confirm that
………………………………………
(name and address of Contractor) is authorized by us to transact in the services required
against your Tender ……………………………… (insert reference number and name of
the Tender) in respect of the above services.

WE HEREBY extend our full guarantee and warranty as per the Conditions of Contract
for the services offered for provision by the above firm against the Invitation to Tender.

DATED THIS…………….. DAY OF……………………………….20……

___________________________________
Signature of duly authorised person for and on behalf of the Manufacturer/ Principal.

__________________________________
Name and Designation of duly authorised person signing on behalf of the Manufacturer/
Principal.

NOTES TO TENDERERS & MANUFACTURERS/ PRINCIPALS/ PRODUCERS

Only a competent person in the service of the Manufacturer/ Principal should sign this
letter of authority.

For provision of motor and alternator rewinding services off grid power station
58

SECTION XIII - DECLARATION FORM


Date
To:
The Kenya Power & Lighting Company Limited,
P.O Box 30099 – 00100,
Stima Plaza, Kolobot Road, Parklands,
Nairobi,
KENYA.

Ladies and Gentlemen,

The Tenderer i.e. (full name and complete physical and postal address)
declare the following: -

a) That I/ We have not been debarred from participating in public procurement by


anybody, institution or person.
b) That I/ We have not been involved in and will not be involved in corrupt and
fraudulent practices regarding public procurement anywhere.
c) That I/We or any director of the firm or company is not a person within the
meaning of paragraph 3.2 of ITT (Eligible Tenderers) of the Instruction to
Tenderers.
d) That I/ We are not insolvent, in receivership, bankrupt or in the process of being
wound up and is not the subject of legal proceedings relating to the foregoing.
e) That I/We do hereby confirm that all the information given in this tender is
accurate, factual and true to the best of our knowledge.
f) That I/ We are not associated with any other Tenderer participating in this tender.

Yours sincerely,
_____________________
Name of Tenderer
___________________________________
Signature of duly authorised person signing the Tender
__________________________________
Name and Designation of duly authorised person signing the Tender

__________________________________
Stamp or Seal of Tenderer

For provision of motor and alternator rewinding services off grid power station
59

SECTION XIV – DRAFT LETTER OF NOTIFICATION OF AWARD

To:
(Name and full address of the Successful Tenderer)…………

Dear Sirs/ Madams,

RE: NOTIFICATION OF AWARD OF TENDER NO. ……………

We refer to your Tender dated………………… and are pleased to inform you that
following evaluation, your Tender has been accepted as follows: -

………………………………………………………………………………………………
………………………………………………………………………………………………

This notification does not constitute a contract. The formal Contract Agreement, which is
enclosed herewith shall be entered into upon expiry of fourteen (14) days from the date
hereof pursuant to the provisions of the Public Procurement and Asset Disposal Act, 2015
(or as may be amended from time to time or replaced).

Kindly sign, and seal the Contract Agreement. Further, initial and stamp on all pages of
the documents forming the Contract that are forwarded to you with this letter. Thereafter
return the signed and sealed Contract together with the documents to us within fourteen
(14) days of the date hereof for our further action.

We take this opportunity to remind you to again note and strictly comply with the
provisions as regards the Tender Security, Signing of Contract and Performance Security
as stated in the Instructions to Tenderers.

We look forward to a cordial and mutually beneficial business relationship.

Yours faithfully,
FOR: THE KENYA POWER & LIGHTING COMPANY LIMITED

GENERAL MANAGER, SUPPLY CHAIN

Enclosures

For provision of motor and alternator rewinding services off grid power station
60

SECTION XV – DRAFT LETTER OF NOTIFICATION OF REGRET

To: (Name and full address of the Unsuccessful Tenderer)………… Date:

Dear Sirs/ Madams,

RE: NOTIFICATION OF REGRET IN RESPECT OF TENDER NO. …………

We refer to your Tender dated………………… and regret to inform you that following
evaluation, your Tender is unsuccessful. It is therefore not accepted. The brief reasons are
as follows:-
1. ………………………
2. ………………………
3. ……………………… etc…

The successful bidder was _______________________.

However, this notification does not reduce the validity period of your Tender Security. In
this regard, we request you to relook at the provisions regarding the Tender Security,
Signing of Contract and Performance Security as stated in the Instructions to Tenderers.

You may collect the tender security from our Legal Department (Guarantees Section), on
the 2nd Floor, Stima Plaza, Kolobot Road, Parklands, Nairobi only after expiry of twenty
five (25) days from the date hereof on Mondays and Wednesdays ONLY between 9.00
a.m to 12.30 pm and 2.00p.m to 4.00p.m.
It is expected that by that time KPLC and the successful bidder will have entered into a
contract pursuant to the Public Procurement and Asset Disposal Act, 2015 (or as may be
amended from time to time or replaced). When collecting the Security, you will be
required to produce the original or certified copy of this letter.

We thank you for the interest shown in participating in this tender and wish you well in
all your future endeavours.

Yours faithfully,
FOR: THE KENYA POWER & LIGHTING COMPANY LIMITED

GENERAL MANAGER, SUPPLY CHAIN

For provision of motor and alternator rewinding services off grid power station
61

SECTION XVI - CONTRACT AGREEMENT FORM

THIS AGREEMENT made this………day of………………….20…. BETWEEN


THE KENYA POWER & LIGHTING COMPANY LIMITED, a limited liability
company duly incorporated under the Companies Act, Chapter 486 of the Laws of
Kenya, with its registered office situated at Stima Plaza, Kolobot Road, Parklands,
Nairobi in the Republic of Kenya and of Post Office Box Number 30099-00100, Nairobi
in the Republic aforesaid (hereinafter referred to as the “KPLC”) of the one part,

AND

……………………………….. (Contractor’s full name and principal place of business)


a duly registered entity according to the laws of..…… (state country) and of Post Office
Box Number/Physical Address ……………….(full address physical and postal of
Contractor) in the Republic aforesaid, (hereinafter referred to as the “Contractor” of the
other part;

WHEREAS KPLC invited tenders for certain services, that is to say for ………………
(KPLC Supply Chain – Procurement Department insert description of services) under
Tender Number…………….. (KPLC Supply Chain – Procurement Department insert
tender number)

AND WHEREAS KPLC has accepted the Tender by the Contractor for the services in
the sum of ……………………( KPLC Supply Chain – Procurement Department
specify the total amount in words which should include any payable taxes, duties and
insurance where applicable e.g. Value Added Tax) (hereinafter called “the Contract
Price”).

NOW THIS AGREEMENT WITNESSETH AS FOLLOWS: -

1. In this Agreement words and expressions shall have the same meanings as are
respectively assigned to them in the Conditions of Contract and the Tender
Document.

2. Unless the context or express provision otherwise requires: -


a) reference to “this Agreement” includes its recitals, any schedules and
documents mentioned hereunder and any reference to this Agreement or to
any other document includes a reference to the other document as varied
supplemented and or replaced in any manner from time to time.

For provision of motor and alternator rewinding services off grid power station
62
b) any reference to any Act shall include any statutory extension,
amendment, modification, re-amendment or replacement of such Act and
any rule, regulation or order made thereunder.
c) words importing the masculine gender only, include the feminine gender
or (as the case may be) the neutral gender.
d) words importing the singular number only include the plural number and
vice-versa and where there are two or more persons included in the
expression the “Contractor” the covenants, agreements obligations
expressed to be made or performed by the Contractor shall be deemed to
be made or performed by such persons jointly and severally.
e) where there are two or more persons included in the expression the
“Contractor” any act default or omission by the Contractor shall be
deemed to be an act default or omission by any one or more of such
persons.

3. In consideration of the payment to be made by KPLC to the Contractor as


hereinbefore mentioned, the Contractor hereby covenants with KPLC to perform
and provide the services and remedy any defects thereon in conformity in all
respects with the provisions of the Contract.

4. KPLC hereby covenants to pay the Contractor in consideration of the proper


performance and provision of the services and the remedying of defects therein,
the Contract Price or such other sum as may become payable under the provisions
of the Contract at the times and in the manner prescribed by the Contract.

5. The following documents shall constitute the Contract between KPLC and the
Contractor and each shall be read and construed as an integral part of the
Contract: -
a) this Contract Agreement
b) the Special Conditions of Contract as per the Tender Document
c) the General Conditions of Contract as per the Tender Document
d) the Price Schedules submitted by the Contractor and agreed upon with
KPLC.
e) the Details of Service as per KPLC’s Tender Document
f) the Schedule of Requirements
g) KPLC’s Notification of Award dated…………
h) the Tender Form signed by the Contractor
i) the Declaration Form signed by the Contractor/ successful Tenderer
j) the Warranty
h) project implementation schedule

For provision of motor and alternator rewinding services off grid power station
63
6. In the event of any ambiguity or conflict between the contract documents
listed above, the order of precedence shall be the order in which the contract
documents are listed in 5 above except where otherwise mutually agreed in
writing.

7. The Commencement Date shall be the working day immediately following the
fulfillment of all the following: -
a) Execution of this Contract Agreement by KPLC and the Contractor.
b) Issuance of the Performance Bond by the Contractor and confirmation of
its authenticity by KPLC.
c) Issuance of the Official Order by KPLC to the Contractor.
d) Where applicable, Opening of the Letter of Credit by KPLC.

8. The period of contract validity shall begin from the Commencement date and end
on either -
a) sixty (60) days after the last date of the agreed performance schedule, or,
b) where a Letter of Credit is adopted as a method of payment, sixty (60)
days after the expiry date of the Letter of Credit or the expiry date of the
last of any such opened Letter of Credit whichever is later.
Provided that the expiry period of the Warranty shall be as prescribed and further
provided that the Warranty shall survive the expiry of the contract.

9. It shall be the responsibility of the Contractor to ensure that its Performance


Security is valid at all times during the period of contract validity and further is in
the full amount as contracted.

10. Any amendment, change, addition, deletion or variation howsoever to this


Contract shall only be valid and effective where expressed in writing and signed
by both parties.

11. No failure or delay to exercise any power, right or remedy by KPLC shall operate
as a waiver of that right, power or remedy and no single or partial exercise of any
other right, power or remedy.

12. Notwithstanding proper completion of performance or parts thereof, all the


provisions of this Contract shall continue in full force and effect to the extent that
any of them remain to be implemented or performed unless otherwise expressly
agreed upon by both parties.

13. Any notice required to be given in writing to any Party herein shall be deemed to
have been sufficiently served, if where delivered personally, one day after such
For provision of motor and alternator rewinding services off grid power station
64
delivery; notices by electronic mail and facsimile shall be deemed to be served
one day after the date of such transmission and delivery respectively, notices sent
by post shall be deemed served seven (7) days after posting by registered post
(and proof of posting shall be proof of service), notices sent by courier shall be

deemed served two (2) days after such receipt by the courier service for Local
Suppliers and five (5) days for Foreign Suppliers.

14. For the purposes of Notices, the address of KPLC shall be Company Secretary,
The Kenya Power & Lighting Company Limited, 7th Floor, Stima Plaza, Kolobot
Road, Post Office Box Number 30099–00100, Nairobi, Kenya. The address for
the Contractor shall be the Contractor’s address as stated by it in the Confidential
Business Questionnaire provided in the Tender Document.

IN WITNESS whereof the parties hereto have caused this Agreement to be executed in
accordance with the laws of Kenya the day and year first above written.

SIGNED for and on behalf


of KPLC

_________________________________
MANAGING DIRECTOR & CEO

and in the presence of:-

______________________
COMPANY SECRETARY

SEALED with the COMMON SEAL


of the CONTRACTOR
in the presence of:-

___________________ ______________________
DIRECTOR Affix Contractor’s Seal here

________________________
DIRECTOR’S FULL NAMES

For provision of motor and alternator rewinding services off grid power station
65

and in the presence of:-

________________________
DIRECTOR/ COMPANY SECRETARY

________________________________________________
DIRECTOR/ COMPANY SECRETARY’S FULL NAMES

DRAWN BY: -
Awuor Owiti,
Advocate,
C/o The Kenya Power & Lighting Company Limited,
7th Floor, Stima Plaza,
Kolobot Road, Parklands,
Post Office Box Number 30099–00100,
NAIROBI, KENYA,

Telephones: + 254-20-3201000/ 731

For provision of motor and alternator rewinding services off grid power station
66

SECTION XVII A - PERFORMANCE SECURITY FORM (BANK GUARANTEE)

(To Be Submitted On Bank’s Letterhead) Date:

To:
The Kenya Power & Lighting Company Limited,
Stima Plaza,
Kolobot Road, Parklands,
P.O Box 30099 – 00100,
Nairobi, Kenya.

WHEREAS…………………………(hereinafter called “the Supplier”) has undertaken,


in pursuance of your Tender Number………………..(reference number of the Tender)
and its Tender dated ………………(insert Supplier’s date of Tender taken from the Tender
Form) to supply ……………(description of the goods) (hereinafter called “the Contract);

AND WHEREAS it has been stipulated by you in the said Contract that the Supplier
shall furnish you with a bank guarantee by an acceptable bank for the sum specified
therein as security for compliance of the Supplier’s performance obligations in
accordance with the Contract;

AND WHEREAS we have agreed to give the Supplier a guarantee;

THEREFORE WE HEREBY AFFIRM that we are Guarantors and responsible to you,


on behalf of the Supplier, up to a total sum of……………………. (amount of the
guarantee in words and figures) and we undertake to pay you, upon your first written
demand declaring the Supplier to be in default under the Contract and without cavil or
argument, any sum or sums within the limits of ………………………………………...
(amount of guarantee) as aforesaid, without you needing to prove or to show grounds or
reasons for your demand or the sum specified therein.

This guarantee is valid until the …………day of……………….…..…20….

EITHER

SEALED with the )


COMMON SEAL )
of the said BANK )
)

For provision of motor and alternator rewinding services off grid power station
67
this ……………………day ) _____________________________
) BANK SEAL
of ………………………20…. )
in the presence of :- )
)
____________________ )
)
and in the presence of:- )
)
__________________ )
OR

SIGNED by the DULY AUTHORISED


REPRESENTATIVE(S)/ ATTORNEY(S) of
the BANK

_____________________
Name(s) and Designation of duly authorised representative(s)/ attorney(s) of the Bank

___________________________________
Signature(s) of the duly authorised person(s)

NOTES TO SUPPLIERS AND BANKS

1. Please note that no material additions, deletions or alterations regarding the


contents of this Form shall be made to the Performance Security Bond (the Bond)
to be furnished by the successful Tenderer/ Supplier. If any are made, the Bond
may not be accepted and shall be rejected by KPLC. For the avoidance of doubt,
such rejection will be treated as non-submission of the Bond where such Bond is
required in the tender and Contract.
2. KPLC shall seek authentication of the Performance Security from the issuing
bank. It is the responsibility of the Supplier to sensitize its issuing bank on the
need to respond directly and expeditiously to queries from KPLC. The period for
response shall not exceed five (5) days from the date of KPLC’s query. Should
there be no conclusive response by the Bank within this period, such Supplier’s
Performance Security may be deemed as invalid and the Contract nullified.
3. The issuing Bank should address its response or communication regarding the
bond to KPLC at the following e-mail address – “guarantees@ kplc.co.ke”

For provision of motor and alternator rewinding services off grid power station
68

SECTION XVII B - PERFORMANCE SECURITY (LC)

Mandatory Conditions that should appear on the Performance Security (LC).

Form of Documentary credit - “Irrevocable Standby”

Applicable rules - “Must be UCP Latest Version” i.e. UCP 600 (2007 REVISION) ICC
Publication No. 600.

Place of expiry - At the counters of the advising bank.

The SBLC should be available – “By Payment”

Drafts should be payable at - “SIGHT”

Documents required -
1. Beneficiary’s signed and dated statement demanding for payment under the letter of
credit no………………………….. (Insert LC No.) as……………………….(Name of
Applicant) (hereinafter called the “Supplier”) indicating that the “Supplier” has
defaulted in the performance and adherence to and performance of the contract
between the Beneficiary and the Supplier.

2. The Original Letter of Credit and all amendments, if any.

Additional Conditions -
1. All charges levied by any bank that is party to this documentary credit are for the
account of the Applicant.

2. (Include) that there should be no conditions requiring compliance with the specific
regulations or a particular country’s laws and regulations.

Charges - All bank charges are for the account of the Applicant.

Confirmation instructions – (See notes below)

NOTES TO SUPPLIERS AND BANKS

1. Please note that should the Performance Security (LC) omit any of the above
conditions the LC shall not be accepted and shall be rejected by KPLC. For the
avoidance of doubt, such rejection will be treated as non-submission of the LC
where such LC is required in the tender and Contract.

2. KPLC may seek authentication of the Performance Security (LC) from the issuing
bank. It is the responsibility of the Supplier to sensitize its issuing bank on the
need to respond directly and expeditiously to queries from KPLC. The period for
For provision of motor and alternator rewinding services off grid power station
69

response shall not exceed three (3) days from the date of KPLC’s query. Should
there be no conclusive response by the Bank within this period, such Supplier’s
Performance Security (LC) may be deemed as invalid and the Contract nullified.

3. The issuing bank should address its response or communication regarding the
bond to KPLC at the following e-mail address – “guarantees@ kplc.co.ke”

4. All Guarantees issued by foreign banks must be confirmed by a local bank in


Kenya.

For provision of motor and alternator rewinding services off grid power station
70

SECTION XVIII – SUBCONTRACTORS

(INFORMATION TO BE PROVIDED BY THE TENDERER)

As per the requirements of Clause 7.23 of General Conditions of Contract, following is a


list of subcontractors and the portions of the Work to be subcontracted:

No. Subcontractor Address Brief Description of the % works


Works to be subcontracted
Subcontracted

For provision of motor and alternator rewinding services off grid power station
71

SECTION XIX - PREVIOUS EXPERIENCE WITH SIMILAR WORK

(INFORMATION TO BE PROVIDED BY THE TENDERER)

As required by Section 3.13.3(d) of the Instructions To Tenderers, following is a list of


work that the Tenderer has previously performed which is similar to that described in the
Request for Proposal:

No. Description Customer Name & Contacts Date of Supply

For provision of motor and alternator rewinding services off grid power station
72

SECTION XX - SUPPLIER EVALUATION FORM


(This form is for information only and not to be filled in by any bidder. It is for
official use by KPLC to evaluate performance of Suppliers during the contract
period)
Name of Firm…………………………………...Date…………………
Category of Product/Service (e.g. Conductors …………………
Period of evaluation………………………………………………........
1. COST OF User Comment Totals
SERVICE/PRODU Supplier Procureme Scor s
CT Rating guidelines Score nt Score e
Did the vendor assist in or advice
on ways of reducing the costs?
PARTIALLY:
YES:4 NO: 0
2

10
How closely did your final costs
correspond to your expectation PARTIALLY:
YES:2 NO: 0
at the beginning of the 1
project/tender? 10.00%
Did the company stick to the
PARTIALLY:
agreed transaction/contract YES:4 NO: 0
2
rates?
Totals
2.ON TIME
DELIVERY OF Did the vendor perform work in
PARTIALLY:
PRODUCT OR compliance with contract terms YES:6 NO: 0
3
SERVICE and agreements? 10
Was the vendor prompt and
PARTIALLY:
effective in correction of YES:2 NO: 0
1
situations and conditions? 10.00%
Are you able to track service level
agreements and determine PARTIALLY:
YES:2 NO: 0
duration of incidents from the 1
vendor?
3. FLEXIBILITY TO Rating guidelines Totals
RESPOND TO Was the vendor willing to change
UNEXPECTED their product/service on special PARTIALLY:
YES:6 NO: 0
DEMAND OF needs? 3
SERVICE 6
6.00%
4. QUALITY Rating guidelines Totals
When performing their duties,
was there - rework or returns PARTIALLY: YES:
NO:6
caused by non-conformance to 3 0
quality? 14
Was the quality of service
PARTIALLY:
delivered equal to KPLC minimum YES:8 NO:0
4
requirements? 14.00%

5.RESPONSIVENE Totals
SS Rating guidelines
Was the vendor well responsive
to information requests, issues, PARTIALLY:
YES:2 NO: 0
or problems that arose in the 1
course of service? 14
Was the vendor open to feedback
PARTIALLY:
on low quality of service levels YES:6 NO: 0
3
and willing to act on this? 14.00%
Is it easy to reach staff members
of suppliers in case of a request PARTIALLY:
YES:6 NO: 0
or query? (are communication 3
channels clear?)
6. CUSTOMER Totals
SUPPORT Rating guidelines
Did the vendor offer effective YES:1 PARTIALLY:
NO: 0
customer support? 0 4 18
In case of reported YES:8 PARTIALLY: NO: 0 18.00%

For provision of motor and alternator rewinding services off grid power station
73
problems/issues, were there 4
follow ups by the vendor to
ensure the problem is fully
resolved during support?

7. Totals
COMMUNICATIO
N SKILLS Rating guidelines
Are you satisfied with the
attitude, courtesy, and PARTIALLY:
YES:2 NO: 0
professionalism of this vendor's 1
staff? Written or spoken? 6
Are the vendor's staff well
equipped and skilled in handling
PARTIALLY:
requests / issues? Are you YES:4 NO: 0
2
rotated too much among staff on
an issue? 6.00%

8. Totals
DOCUMENTATIO
N AND
ACCOUNTING Rating guidelines
Are you satisfied with how the
Vendor presents documentation
(invoices & licenses etc) when PARTIALLY:
YES:6 NO: 0
required to do so, to necessitate 3
finalization of contract renewals
and payments? 10
Was problem documentation
(incident reports) presented PARTIALLY:
YES:4 NO: 0
promptly by the vendor and was 2
it complete? 10.00%

9. VALUE ADD Rating guidelines Totals


Did the vendor go over and
above in optimizing service PARTIALLY:
YES:6 NO: 0
delivery process for effective 3
services delivery? 12
Did the vendor go over and
above and offer training or PARTIALLY:
YES:6 NO: 0
knowledge to assist with better 3
systems support? 12.00%

Totals
Score:
Totals 100.0
100.
Maximum Score
0 100.00%
VENDOR'S TOTAL SCORE
VENDOR'S PERCENTAGE SCORE
ISSUES FOR FOLLOW UP -
Evaluation Done
by: Name Department Date

Checked/Validate
d by

Score in Percentage % ………………………………………

PERFORMANCE LEVEL DEFINATION;


≥75% - KP1 GREEN
50% - KP2 AMBER
25% - KP3 YELLOW
≥25% - KP4 RED

RATING: 75% - V Good, 50% - Good, 25% - Fair, Below 25% - Poor

For provision of motor and alternator rewinding services off grid power station
74

RECOMMENDATION

Status Tick as appropriate


1 Grant supplier preferred status KP1
2 Work with supplier or develop and KP2 & KP3
improve supplier
3 Abandon / switch suppliers KP4

Name:…………………………Sign:…………………………..Date:………...

Name:…………………………Sign:…………………………..Date:………...

Name:…………………………Sign:…………………………..Date:………...

For provision of motor and alternator rewinding services off grid power station
75

SECTION XXI - THE DETAILS OF SERVICES

The Details of Services describe the basic requirements for services. In addition to the
information and documentation in the Tender Document regarding the technical aspects
of this tender, all Tenderers shall comply with the following -

PART A - GENERAL REQUIREMENTS

1. Technical documentation shall be in English language. The specific services on offer


shall be marked clearly for the services they intend to provide.

2. Deviations from the basic requirements, if any, shall be explained in detail in writing
with the offer, with supporting data including calculation sheets, detailed drawings
and certified test reports. KPLC reserves the right to reject the services if such
deviations shall be found critical to the use and operation of the services.

3. The Contractor shall submit a Commentary on the Details of Service as well as


Commentary of Compliance to the Details of Service. In submitting the
Commentaries the Contractors and or Manufacturers/ Principals should provide cross-
references to the documents submitted.

4. The Commentaries shall be in table form, and shall cover in detail, all clauses of the
Detail(s).

5. Detailed contact information including title, e-mail, facsimile, telephone or any other
form of acceptable communication of the certification or recognition and standards
body used shall be provided.

6. Where Certificates and their Reports and are translated into English, all pages of the
translations must be signed and stamped by the certifying authority.

7. The Manufacturer’s/ Principal’s Declaration of Conformity to reference standards and


copies of quality management certifications including valid and current ISO
certifications shall be submitted for evaluation.

8. In all cases where the level of galvanizing and painting is not specifically stated in
the Details, the general requirement shall be for a uniform coating of thickness not
less than 80 microns.

For provision of motor and alternator rewinding services off grid power station
76

9. Contractors are required to provide information on proper representative(s) and or


workshop for back-up service and or repair and maintenance including their names,
telephone, facsimile, e-mail, physical and postal addresses, along with their offers.

For provision of motor and alternator rewinding services off grid power station
77

PART B – SPECIFIC DETAILS OF SERVICE (SDS)

The Specific Details of Service are as follows:-

1. REWINDING OF 1NO. 500KVA PERKINS GENSET ALTERNATOR


EXCITER ARMATURE WINDINGS.

Alternator type: Leroy somer


Model: LSA 47.2 M7 C 6/4
Serial nos.: 204886/5;
AVR type: R448- AREP
Rating: 3 phase, 400v, 50 Hz, 0.8 pf, 500kva.

The following is to be done.


I. Dismantling of the main stator, rotative field winding, exciter windings,
service all windings, carry out H.V.insulation, Resistance and Prime tests,
stator core lamination hot spot tests.
II. Rewinding the armature exciter winding as per the original model
mentioned above.
III. Varnish and oven cure as required.
IV. Assemble the parts ensuring proper alignment.
V. Clean all the mechanical parts.
VI. Re place the NDE bearing.( bearing part no. 6315- 2RS)
VII. Provide and fix all covers, lost nuts and bolts of the side and top covers.
VIII. Provide 4 no. Lost nuts for the main terminal block and the missing copper
bar terminal .
IX. Apply paint as necessary.
X. Supply and fit diodes as necessary.
XI. Assemble all parts as required
XII. Carry out insulation and resistance testing of the following upon delivery;
main stator winding, rotor winding, exciter field and armature windings
and auxiliary windings.

2. REWINDING OF 1 NO.500 KVA PERKINS GENSET ALTERNATOR


FIELD AND ARMATURE WINDINGS

Alternator type: LSA 47.2 M7 C6/4


Serial nos.: 204886/10
AVR type: R 448
Rating: 3 phase, 415v, 50 Hz, 0.8 pf, 455kva.

The following is to be done.


i. Dismantling of the main stator, rotative field winding, exciter
windings, service all windings, carry out H.V.insulation,
Resistance and Prime tests, stator core lamination hot spot tests.
ii. Rewinding the field and armature exciter as per the original model
mentioned above.
For provision of motor and alternator rewinding services off grid power station
78
iii. Varnish and oven cure as required.
iv. Assemble the parts ensuring proper alignment
v. Clean all the mechanical parts.
vi. Inspect and replace bearings as per type.
vii. Provide and fix all covers, lost nuts and bolts of the side and top
covers.
viii. Apply paint as necessary.
ix. Supply and fit diodes as necessary.
x. Carry out insulation and resistance testing of the following upon
delivery; main stator winding, rotor winding, exciter field and
armature windings and auxiliary windings.

3. BEARING INSPECTION AND ALIGNMENT OF 2.NO 500KVA


ALTERNATORS

Alternator type: LSA M7 C 6/4


Serial nos: 211322/5 and 223766/1
AVR: R448

The following is to be done:


i. Disassembly of the parts
ii. Inspect and replace the NDE bearing
iii. Provide and replace all missing covers and lost nuts
iv. Clean all windings
v. Apply paint as necessary
vi. Supply and fit the diode assembly
vii. Assemble parts ensuring proper alignment.
viii. Carry out insulation and resistance testing of the following; main stator
winding , rotor winding, exciter field and armature windings and auxiliary
windings

4. BEARING AND WINDING INSPECTION OF 315 KVA LEROY SOMER


ALTERNATOR

Alternator type: LSA 46.2 VL12C6/4


Serial nos.: 199074/3
AVR type: R 448
Rating: 3 phase, 415v, 50 Hz, 0.8 pf, 455kva.

The following is to be done:

i. Dismantling of the main stator, rotative field winding, exciter windings,


service all windings, carry out H.V.insulation, Resistance and Prime tests,
stator core lamination hot spot tests.
ii. Inspect and replace the NDE bearing
iii. supply and replace the diode bridge assembly
iv. Provide and replace all missing covers and lost nuts
For provision of motor and alternator rewinding services off grid power station
79
v. Clean all windings
vi. Apply paint as necessary
vii. Assemble parts ensuring proper alignment.
viii. Carry out insulation and resistance testing of the following; main stator
winding, rotor winding, exciter field and armature windings and auxiliary
windings.

5. COUPLING SHEETS REPLACEMENT FOR STAMFORD


ALTERNATOR 282KVA

i. Disassemble the parts


ii. Replace the worn out coupling sheets ensuring the quality of the
material used is maintained
iii. Assemble the parts ensuring proper alignment.

NOTES
a. The bidders will be required to view the alternators at Nairobi south
b. Testing will be done before delivery.

For provision of motor and alternator rewinding services off grid power station
80

SAMPLE VIEWING FORM

ISO 9001:2008 QMS SUPPLIES Doc. No. KP1/9A.1A/RT/039/18-19


WORK INSTRUCTIONS
SECTION: OGS Issue No.

Revision No.

Date of Issue

SUBJECT: SAMPLE
VIEWING FORM

The Kenya Power & Lighting


Co. Ltd

Signature Date

NAME OF KPLC STORES OFFICIAL:

NAME OF SUPPLIER’S REPRESENTATIVE:

KPLC
NO CODE ITEM DESCRIPTION REMARKS
Rewinding of 1no. 500kva perkins genset alternator exciter
1 armature windings.
Rewinding of 1 no.500 kva perkins genset alternator field and
2 armature windings
Bearing inspection and alignment of 2.no 500kva alternators
3
Bearing and winding inspection of 315 kva leroy somer
4 alternator
Coupling sheets replacement for stamford alternator 282kva
5

For provision of motor and alternator rewinding services off grid power station

You might also like