AS 1627.

1—2003
AS 1627.1

Australian Standard™

Metal finishing—Preparation and

This is a free 7 page sample. Access the full version online.

pretreatment of surfaces

Part 1: Removal of oil, grease and

related contamination
 This Australian Standard was prepared by Committee MT-009, Metal Finishing. It
was approved on behalf of the Council of Standards Australia on 11 April 2003 and
published on 2 June 2003.

The following are represented on Committee MT-009:

Australasian Institute of Metal Finishing
Australian Chamber of Commerce and Industry
Australian Industry Group
Australian Paint Manufacturers Federation
Department of Defence
Galvanizers Association of Australia
Institute of Materials Engineering Australia
This is a free 7 page sample. Access the full version online.

Powder Coaters Association

The Royal Australian Chemical Institute
Society of Automotive Engineers—Australasia
Telstra Corporation

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology and
systems. To maintain their currency, all Standards are periodically reviewed, and
new editions are published. Between editions, amendments may be issued.
Standards may also be withdrawn. It is important that readers assure themselves
they are using a current Standard, which should include any amendments which
may have been published since the Standard was purchased.
Detailed information about Standards can be found by visiting the Standards
Australia web site at www.standards.com.au and looking up the relevant Standard
in the on-line catalogue.
Alternatively, the printed Catalogue provides information current at 1 January each
year, and the monthly magazine, The Australian Standard, has a full listing of
revisions and amendments published each month.
We also welcome suggestions for improvement in our Standards, and especially
encourage readers to notify us immediately of any apparent inaccuracies or
ambiguities. Contact us via email at [email protected], or write to the Chief
Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW
2001.

This Standard was issued in draft form for comment as DR 02404.

 AS 1627.1—2003

Australian Standard™

Metal finishing—Preparation and

This is a free 7 page sample. Access the full version online.

pretreatment of surfaces

Part 1: Removal of oil, grease and

related contamination

Originated as AS CK9.1—1965.
Previous edition AS 1627.1—1989.
Third edition 2003.

COPYRIGHT
© Standards Australia International
All rights are reserved. No part of this work may be reproduced or copied in any form or by any
means, electronic or mechanical, including photocopying, without the written permission of the
publisher.
Published by Standards Australia International Ltd
GPO Box 5420, Sydney, NSW 2001, Australia
ISBN 0 7337 5257 8
 AS 1627.1—2003 2

PREFACE
This Standard has been prepared by the Australian members of the Joint Standards
Australia/Standards New Zealand Committee MT-009, Metal Finishing, to supersede
AS 1627.1—1989. After consultation with stakeholders in both countries, Standards
Australia and Standards New Zealand decided to develop this Standard as an Australian
Standard rather than an Australian/New Zealand Standard.
This Standard was revised by Standards Australia Subcommittee MT-009-05 which decided
to change the title from Metal finishing, Part 1: Cleaning using liquid solvents or alkaline
solution to Metal finishing, Part 1: Removal of oil, grease and related contamination as the
latter better reflects the content of the Standard.
The objective of this Standard is to specify the procedures for the removal of surface
contaminants on metallic surfaces.
This Standard forms Part 1 of a series of Standards that deal with the preparation and pre-
treatment of metal surfaces in readiness for finishing processes.
The series comprises the following Parts:
This is a free 7 page sample. Access the full version online.

AS
1627 Metal finishing—Preparation and pretreatment of surfaces
1627.0 Part 0: Method selection guide
1627.1 Part 1: Removal of oil, grease and related contamination
1627.2 Part 2: Power tool cleaning
1627.4 Part 4: Abrasive blast cleaning
1627.5 Part 5: Pickling
1627.6 Part 6: Chemical conversion treatment of metals
1627.9 Part 9: Pictorial surface preparation standards for painting steel surfaces
The term ‘informative’ has been used in this Standard to define the application of the
appendix to which is applies. An ‘informative’ appendix is only for information and
guidance.
 3 AS 1627.1—2003

CONTENTS

Page

FOREWORD.............................................................................................................................. 4

SECTION 1 SCOPE AND GENERAL

1.1 SCOPE......................................................................................................................... 5
1.2 REFERENCED DOCUMENTS................................................................................... 5
1.3 DESIGNATION .......................................................................................................... 5
1.4 DEFINITIONS............................................................................................................. 6
1.5 SURFACE CLEANLINESS ....................................................................................... 6

SECTION 2 SURFACE CLEANING PROCESSES

2.1 GENERAL................................................................................................................... 8
2.2 NEUTRAL/ALKALINE PROCESSES........................................................................ 8
2.3 SOLVENT PROCESSES............................................................................................ 9
This is a free 7 page sample. Access the full version online.

2.4 EMULSION PROCESSES ........................................................................................ 10

2.5 HIGH PRESSURE CLEANING PROCESSES ......................................................... 10
2.6 CORROSION PROTECTION ................................................................................... 11
2.7 SAFETY PRECAUTIONS ........................................................................................ 11

APPENDICES
A PURCHASING GUIDELINES .................................................................................. 12
B GUIDE TO THE SELECTION OF CLEANING PROCESS ..................................... 13
 AS 1627.1—2003 4

FOREWORD
This Standard describes methods and materials used to remove contaminants such as oil,
grease and related contaminates from metal and previously coated surfaces prior to further
surface preparation or coating.
Such methods are used prior to mechanical methods such as power tool cleaning or abrasive
blasting. Methods included in the procedures are simple solvent wiping, immersion in
solvent, solvent spray, vapour degreasing, emulsion cleaning and alkaline cleaning.
Solvent cleaning is not a suitable method for the removal of corrosive salts. These require
treatment, according to the degree of contamination, by washing with suitable aqueous
solutions, possibly utilizing high pressure water.
Liquid solvent cleaning seldom completely removes all oil and grease. Supplementary
cleaning processes may be required to produce suitably clean surfaces for some coating
systems. Solvent vapour degreasing is capable of removing all oil and grease deposits.
Successful coating of a metal component or structural items, whether with a paint system or
another metal (such as zinc), lies in rendering its surface completely free of any foreign
This is a free 7 page sample. Access the full version online.

matter, notably dirt or greasy substances, that will interfere either with the coating
operation itself or with the ultimate performance of the coating in service. The presence of
unremoved contamination is likely to result in an unsatisfactory coating finish, such as
blistering and bare areas, or in disbonding of an apparently satisfactory coating from the
substrate with the passage of time.
A wide range of alkaline cleaning products and methods is available, and the nature of the
final coating must be taken into account as the final performance may be affected by the
cleaning method selected. It is also essential that residues of alkaline cleaning compounds
and detergents be removed, as these can be detrimental to performance. Alkaline cleaning is
suitable for removal of dirt, perspiration, light deposits of oil and some water wettable or
soluble contaminants.
 5 AS 1627.1—2003

STANDARDS AUSTRALIA
Australian Standard
Metal finishing—Preparation and pretreatment of surfaces

Part 1: Removal of oil, grease and related contamination

SECT ION 1 SCOPE AND GENERA L

1.1 SCOPE
This Standard sets out a variety of methods for eliminating dirt and organic residues, such
as oil, grease and related contaminates from metal surfaces, so as to facilitate the
satisfactory application of finished coatings. Methods described for decontaminating
surfaces include simple solvent wiping, immersion in solvent, solvent spray, vapour
degreasing, emulsion cleaning, and alkaline cleaning. The process will usually remove
This is a free 7 page sample. Access the full version online.

loose adherent dirt from affected surfaces.

Depending on the nature of the finish coating to be applied, cleaning by any of the
procedures described in this Standard may be followed by a more rigorous intermediate
treatment, such as pickling or abrasive blast cleaning.
NOTE: Appendix A contains advice and recommendations on information which should be
supplied by the purchaser at the time of inquiry or order.

1.2 REFERENCED DOCUMENTS

The documents below are referred to in this Standard.
AS
2661 Vapour decreasing plant—Design, installation and operation—Safety
requirements
3894 Site testing of protective coatings
3894.6 Method 6: Determination of residual contaminants
4108 Metal finishing—Glossary of terms used in electroplating and related processes
AS/NZS
1337 Eye protectors for industrial applications
1715 Selection, use and maintenance of respiratory protective devices
1716 Respiratory protective devices

1.3 DESIGNATION
The designations adopted for the various types of cleaning processes given in Table 2.1 are
listed below:
(a) Neutral/Alkaline degreasing process (A)
AS ........ Neutral/Alkaline spray process
AD ....... Neutral/Alkaline dip or soak process
ADM .... AD process with mechanical and/or ultrasonic agitation
AE........ Alkaline electrolytic

www.standards.com.au  Standards Australia

 AS 1627.1-2003 Metal finishing - Preparation and pretreatment of surfaces - Removal of oil,
grease and related contamination

The remainder of this document

This is a free 7 page sample. Access the full version online.

is available for purchase online at

infostore.saiglobal.com/store

SAI Global also carries a wide range of publications from a wide variety of Standards Publishers:

Business
Information

DIN

AS
AMERICAN SOCIETY
VDLUFA

...
FOR QUALITY TM

Plus many more on infostore.saiglobal.com/store