Klass.-Nr.

01 15 5 June 2005

Norm vor Anwendung auf Aktualität prüfen / Check standard for current issue prior to usage.
Manufacturer's Code VW
for Vehicle Parts 105 40-1
Konzernnorm
Descriptors: manufacturer, code, indentification, vehicle part

Changes
The following changes have been made as compared to Volkswagen standard VW 105 40-1, 1999-
06:
─ Section 1, paragraph 1: “..three or four-digit ..” changed to “…three-character…”
─ Section 1, paragraph 1: Note on VW 105 14, VW 105 50, DIN 14 50 removed, “code” changed
to “manufacturer's code”
─ Section 1, paragraphs 4 and 5: Notes on contact partners and hyperlinks added.
─ Section 1, paragraph 6: Note on “moldings” removed; alternative identifications supplemented
─ Section 2: paragraph 1 removed
─ Section 2, paragraph 2: Note added on missing identifications
─ Section 2: Note added regarding VW 105 00
─ Section 3.1, Figure 1: Part number and date of manufacturing updated

Previous issues
1972-10; 1999-06

1 Scope
Vehicle parts or function groups that are purchased ready to be installed from vendors, are partially
supplied by vendors, are taken from current production as spare or accessory parts, or are
manufactured in-house as spare or accessory parts must be identified by a permanent and easily
legible three-character manufacturer's code (alphabetic or alphanumeric) indicating the
manufacturer.
Identification by the manufacturer's code is required so that selective damage and quality analysis
can be carried out if necessary and so that the manufacturer can always be identified in warranty
and product liability cases.
Manufacturer's codes have been established for all manufacturers and their individual production
locations that supply vehicle parts to the Volkswagen Group and its brands, including its associated
companies.
The manufacturer's codes for Volkswagen AG and Audi AG are assigned on request.
Suppliers can access information on contacts and procedures via the B2B supplier platform at
www.vwgroupsupply.com.
The manufacturer is notified of the assignment of the manufacturer code in writing.
Manufacturer's codes for foreign affiliated companies are issued separately according to the issuing
specifications defined in VW 105 40-3. The contacts for assigning manufacturer's codes in the
Group companies abroad are likewise available via the B2B supplier platform at
www.vwgroupsupply.com.
A list of all manufacturer's codes (only for internal use) and contacts for awarding the
manufacturer's code are likewise available in the NOLIS system at
http://few.wob.vw.de/anbieter/eztn/herstellercode/code.xls.
Form FE 41 - 01.05

Page 1 of 4
Fachverantwortung/Responsibility Normung/Standards (EZTD, 1733)
EZTD Kühn Kühn Tel: +49-5361-9-23370 Sobanski

Confidential. All rights reserved. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group.
Parties to a contract can only obtain this standard via the B2B supplier platform “www.vwgroupsupply.com”.
 VOLKSWAGEN AG
Page 2
VW 105 40-1: 2005-06

The identification requirement for vehicle parts may be dropped in the following cases:
─ standard parts
─ semifinished parts,
─ parts for which identification is not possible because of space limitations and/or cannot be
applied so that it is readable (see DIN 1450 for this term).
For parts which, due to their nature, cannot be identified with the manufacturer's code as per this
standard, alternative forms of identification shall be agreed between the manufacturer and the
center awarding the manufacturer's code, as shall the inclusion of same in the appropriate
documents.
Exception: For valve springs, color markings acc. to VW 105 40-7 are assigned to the manufacturer
as an alternative manufacturer's code.

2 Requirements
Part identification shall be established immediately for newly developed items and first-order items.
Missing identifications shall be applied immediately. Identification specification according to Figure
2 shall be ensured. Any codes that do not apply shall be deleted.
The code characters shall be half the size of the trademark diameter “d1” or the trademark height
“h” acc. to VW 105 14 if possible, but even when space is limited the size shall never be less than
2 mm.
Assemblies (ASSY) that are sold as spare parts shall only be identified once by such a code,
whereas any component part of an assembly that is listed individually as a spare part shall also be
identified by a code.
The identification on the part should if possible be located so that it is visible in as-installed position.
When identifying parts that are in the visual range of the customer, agreement shall be reached
with Design and the center assigning the manufacturer's code on the application position of the
identification.
Typeface according to DIN 1451, part 4 (medium-spaced lettering) applies to the identification.
VW 105 00 contains further identification requirements.
 Page 3
VW 105 40-1: 2005-06

3 Identification example (Figure 1) and drawing specifications (Figure 2)

3.1 Identification example

1)
2)

(DE)
3)
2)
05

3D0

Figure 1

3.2 Drawing specifications for Figure 1 (text macro; VW 010 14, NO-E2):
Kennzeichnung VW 105 00
Identification
Markenzeichen VW 105 14 - C6
Trademark
Herstellland VW 105 50 – 3
Country of origin
Hersteller-Code3) VW 105 40 – 3
Mfr. Code
Teil-Nr.; Schrift DIN 1451 – 3
Pt.-No; Lettering
Datumskennzeichnung VW 105 60 - A6
Date of manufact.
Werkstoff-Code VDA 260 > PP + EPDM <
Material code
Figure 2

1) In case of lack of space the 2-letter code acc. to VW 105 50 shall be used.
2) Manufacturer's code has 3 characters
3) Instead of the manufacturer's code acc. to VW 105 40, part 7 of the same standard shall be applied to valve springs.
Page 4
VW 105 40-1: 2005-06

4 Referenced standards
DIN 1450 Lettering, Legibility
DIN 1451-4 Typefaces; Lineal Linear-Antiqua; Stenciled Lettering for Engraving and Other
Processes
VW 010 14 Technical Drawings; Drawing Frames and Text Macros
VW 105 00 Company Designation, Parts Identification; Guidelines for Use
VW 105 14 Logos; Identification of Vehicle Parts
VW 105 40-3 Manufacturer's Code fro Vehicle Parts; Issuing Ranges for International Plants
Issuing Manufacturer's Codes
VW 105 40-7 Identification of Valve Springs