NX300

UHF DIGITAL TRANSCEIVER
NX-300
SERVICE MANUAL
© 2007-10 PRINTED IN JAPAN
B51-8811-00 (S) 243
NX-300 K3 NX-300 K
Helical Antenna
(KRA-23:option)
Knob (Selector) Knob (Selector)
(K29-9408-13) (K29-9408-13)
Knob (Volume) Knob (Volume)
(K29-9407-03) (K29-9407-03)
Badge Badge
(B43-1606-04) (B43-1606-04)
Knob (PTT) Knob (PTT)

(K29-9405-03) (K29-9405-03)
Packing (6 key)
(G53-1765-11)
MIC MIC
Plastic cabinet assy

(18 key) Plastic cabinet assy
(A02-4003-13) (6 key)
Packing (18 key) (A02-4002-13)
1 3 DEF
(G53-1766-11) 4 GHI
2 ABC
6 MN
O
5 JKL
7 PQ Z
RS 9 WXY
8 TUV
#
0
Does not come with antenna. Antenna is available as an option.
CONTENTS
GENERAL ............................................................... 2 SCHEMATIC DIAGRAM
SYSTEM SET-UP ................................................... 2 CONTROL UNIT (X53-4260-XX) .................... 72
REALIGNMENT ...................................................... 3 TX-RX UNIT (X57-7370-10) ............................ 82
DISASSEMBLY FOR REPAIR ................................ 6 INTERCONNECTION DIAGRAM ......................... 86
CIRCUIT DESCRIPTION ......................................... 9 BLOCK DIAGRAM ................................................ 88
COMPONENTS DESCRIPTION ........................... 15 LEVEL DIAGRAM ................................................. 92
PARTS LIST .......................................................... 17 OPTIONAL ACCESSORIES
EXPLODED VIEW ................................................. 28 KNB-47L (Li-ion BATTERY PACK) ................. 93
PACKING .............................................................. 29 KNB-48L (Li-ion BATTERY PACK) ................. 93
ADJUSTMENT ..................................................... 30 SPECIFICATIONS .............................. BACK COVER
TERMINAL FUNCTION ........................................ 52
PC BOARD
CONTROL UNIT (X53-4260-XX) .................... 64
TX-RX UNIT (X57-7370-10) ............................ 68
This product complies with the RoHS directive for the European market. This product uses Lead Free solder.
NX-300
GENERAL / SYSTEM SET-UP
Document Copyrights INTRODUCTION

Copyright 2007 by Kenwood Corporation. All rights reserved. SCOPE OF THIS MANUAL
No part of this manual may be reproduced, translated, This manual is intended for use by experienced technicians
distributed, or transmitted in any form or by any means, elec- familiar with similar types of commercial grade communications
tronic, mechanical, photocopying, recording, or otherwise, equipment. It contains all required service information for the
for any purpose without the prior written permission of equipment and is current as of the publication date. Changes
Kenwood. which may occur after publication are covered by either Service
Bulletins or Manual Revisions. These are issued as required.
Disclaimer
While every precaution has been taken in the preparation ORDERING REPLACEMENT PARTS
of this manual, Kenwood assumes no responsibility for errors When ordering replacement parts or equipment information, the
or omissions. Neither is any liability assumed for damages full part identification number should be included. This applies to all
resulting from the use of the information contained herein. parts : components, kits, or chassis. If the part number is not known,
Kenwood reserves the right to make changes to any products include the chassis or kit number of which it is a part, and a sufficient
herein at any time for improvement purposes. description of the required component for proper identification.
Firmware Copyrights PERSONAL SAFETY

The title to and ownership of copyrights for firmware The following precautions are recommended for personal safety:
embedded in Kenwood product memories are reserved for • DO NOT transmit until all RF connectors are verified se-
Kenwood Corporation. Any modifying, reverse engineering, cure and any open connectors are properly terminated.
copy, reproducing or disclosing on an Internet website of the • SHUT OFF and DO NOT operate this equipment near elec-
firmware is strictly prohibited without prior written consent of trical blasting caps or in an explosive atmosphere.
Kenwood Corporation. Furthermore, any reselling, assigning • This equipment should be serviced by a qualified technician only.
or transferring of the firmware is also strictly prohibited with-
out embedding the firmware in Kenwood product memories.
SERVICE
NXDN Transceivers: This transceiver is designed for easy servicing. Refer to
The AMBE+2(TM) voice coding technology is embedded in the schematic diagrams, printed circuit board views, and
the firmware under the license of Digital Voice Systems, Inc. alignment procedures contained within.
SYSTEM SET-UP
Merchandise received
License and frequency allocated by FCC Frequency range (MHz) RF power Type DTMF keypad
TX/RX 450~520 5W NX-300 K No
Choose the type of transceiver TX/RX 450~520 5W NX-300 K3 Yes
A personal computer (IBM PC or compatible), programming interface
(KPG-36/36A), USB adapter(KCT-53U), and programming software (KPG-111D)
Transceiver programming
are required for programming.
(The frequency, and signaling data are programmed for the transceiver.)
YES
Are you using the optional antenna? KRA-23 or KRA-27
Optional antenna
NO
(Option)
YES
Are you using the speaker microphone? KMC-25
Speaker microphone
NO
(Option)
YES
Are you using the voice guide & storage unit? VGS-1
NO (Option)
Delivery
2
NX-300
REALIGNMENT
1. Modes 2. How to Enter Each Mode

Mode Operation
User mode
User mode Power ON
Panel test mode [ ] + Power ON
Unprogramming mode PC mode Received commands from PC
Panel tuning mode Press the [ ] key, in Panel test mode
Panel test mode Panel tuning mode Firmware [ ] + Power ON
programming mode
PC mode Data programming mode Clone mode [ ] + Power ON
Firmware version [Side1] + Power ON
Firmware PC test mode PC tuning mode information
programming mode
Clone mode 3. Panel Test Mode

Setting method refer to ADJUSTMENT.
Firmware version information
4. Panel Tuning Mode

Mode Function
Setting method refer to ADJUSTMENT.
User mode For normal use.
Unprogramming mode If you turn the transceiver power ON using
any one of the following conditions, the
5. PC Mode
transceiver forcibly enters Unprogramming mode.
5-1. Preface
• FPU data is not written.
The transceiver is programmed by using a personal com-
• No channel are programmed.
puter, programming interface (KPG-36/36A), USB adapter
• When using kill.
(KCT-53U) and programming software (KPG-111D).
• The ESN is not written. The programming software can be used with an IBM PC
• Broken hardware has been detected. or compatible. Figure 1 shows the setup of an IBM PC for
Panel test mode Used by the dealer to check the funda- programming.
mental characteristics.
Panel tuning mode Used by the dealer to tune the transceiver. IBM-PC
PC mode Used for communication between the KPG-36 or KPG-36A or
KPG-36A + KCT-53U
transceiver and PC (IBM compatible). Illustration is KPG-36.
Data programming Used to read and write frequency data and
mode other features to and from the transceiver.
PC test mode Used to check the transceiver using the PC.
This feature is included in the FPU.
See pages 39 to 51.
Firmware Used when changing the main program
programming mode of the flash memory.
Clone mode Used to transfer programming data from
one transceiver to another. M
KPG-111D
IC
Firmware version Used to confirm the internal firmware

information version. 1
7
GH
I 2 ABC
3 DEF
PC PC PC
D-SUB D-SUB
USB
(25-pin) (9-pin)
KCT-53U
KPG-36 KPG-36A
KPG-36A
Transceiver Transceiver Transceiver
Fig. 1
3
NX-300
REALIGNMENT
5-2. Connection procedure 6-3. Programming
1. Connect the transceiver to the computer using the inter- 1. Start up the firmware programming software (Fpro.exe
face cable and USB adapter (When the interface cable is (version 4.0 or later))
KPG-36A, the KCT-53U can be used.). 2. Set the communications speed (normally, 115200 bps)
and communications port in the configuration item.
Notes: 3. Set the firmware to be updated by File name item.
• You must install the KCT-53U driver in the computer to 4. Press and hold the [ ] key while turning the transceiver
use the USB adapter (KCT-53U). power ON. Then, the orange LED on the transceiver lights
• When using the USB adapter (KCT-53U) for the first time, and “PROGRAM 115200” is displayed.
plug the KCT-53U into a USB port on the computer with 5. Check the connection between the transceiver and the
the computer power ON. personal computer, and make sure that the transceiver is
in the Program mode.
2. When the POWER switch on, user mode can be entered 6. Press “write” button in the window. When the trans-
immediately. When PC sends command the transceiver ceiver starts to receive data, the [LOADING] display lights.
enter PC mode, and “PROGRAM” is displayed on the LCD. 7. If writing ends successfully, the checksum is calculated
When data transmitting from transceiver, the red LED is lights. and a result is displayed.
When data receiving to transceiver, the green LED is lights. 8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
Note:
The data stored in the computer must match the "Model Note:
Name" when it is written into the flash memory. This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming software.
5-3. KPG-36/KPG-36A description
(PC programming interface cable: Option) 6-4. Function
The KPG-36/36A is required to interface the transceiver to 1. If you press the [Side2] key while “PROGRAM 115200” is
the computer. It has a circuit in its D-sub connector (KPG-36 displayed, the display changes to “PROGRAM 19200”
: 25-pin, KPG-36A : 9-pin) case that converts the RS-232C (The LED blinks green) to indicate that the write speed is
logic level to the TTL level. low speed (19200 bps). If you press the [Side2] key again
The KPG-36/36A connects the universal connector of the while “PROGRAM 19200” is displayed, the display
transceiver to the RS-232C serial port of the computer. changes to “PROGRAM 38400” (The LED lights red and
orange alternatively). If you press the [Side2] key again
5-4. KCT-53U description (USB adapter : Option) while “PROGRAM 38400” is displayed, the display
The KCT-53U is a cable which connects the KPG-36A to a changes to “PROGRAM 57600” (The LED blinks orange).
USB port on a computer. If you press the [Side2] key again while “PROGRAM
When using the KCT-53U, install the supplied CD-ROM 57600” is displayed, the display returns to “PROGRAM
(with driver software) in the computer. The KCT-53U driver 115200” (The LED lights orange).
runs under Windows 2000 or XP. 2. If you press the [Side1] key while “PROGRAM 115200” is
displayed, the checksum is calculated, and a result is dis-
5-5. Programming software KPG-111D description played. If you press the [Side1] key again while the
The KPG-111D is the programming software for the trans- checksum is displayed, “PROGRAM 115200” is
ceiver supplied on a CD-ROM. This software runs under MS- redisplayed.
Windows 2000 or XP on an IBM-PC or compatible machine.
The data can be input to or read from the transceiver and Note:
edited on the screen. The programmed or edited data can be Normally, write in the high-speed mode.
printed out. It is also possible to tune the transceiver.
7. Clone Mode
6. Firmware Programming Mode Programming data can be transferred from one transceiver
6-1. Preface to another by connecting them via their external universal con-
Flash memory is mounted on the transceiver. This allows nectors. The operation is as follows (the transmit transceiver is
the transceiver to be upgraded when new features are re- the source and the receive transceiver is a target).
leased in the future. (For details on how to obtain the firm- The following data cannot be cloned.
ware, contact Customer Service.) • Tuning data
• Embedded message with password
• Model name data
6-2. Connection procedure
• ESN (Electronic Serial Number) data
Connect the transceiver to the personal computer (IBM
PC or compatible) using the interface cable (KPG-36/36A) and
USB adapter (KCT-53U : when the interface cable is KPG-
36A, the KCT-53U can be used.). (Connection is the same as
in the PC Mode.)
4
NX-300
REALIGNMENT
Key guide on the Read authorization password input screen. Notes:
• CONFRM ([ ] key):The password confirmation • Cannot be cloned if the password (overwrite password) is
• DELETE ([ ] key): Delete the least digit from the current programmed to the target.
password number (Press and hold to • “Model Name” must be same to clone the transceiver.
delete all password numbers)
• SELECT ([ ] key): Determine the least digit of the pass- Cloning cable
(E30-3325-05)
word number
1. Press and hold the [ ] key while turning the transceiver

power ON. If the Read authorization password is set to
the transceiver, the transceiver displays “CLONE LOCK”.
If the password is not set, the transceiver displays
“CLONE MODE”.
2. When you enter the correct password, and “CLONE
MODE” is displayed, the transceiver can be used as the M
IC
M
IC
cloning source. The following describes how to enter the

password.
1 1
4 4
GH GH
I 2 ABC I 2 ABC
3 DEF 3 DEF
7 7
3.
• How to enter the password using the keypad (K3
Fig. 2
model only);
If the [ ]/[ ] key is pressed while "CLONE LOCK" is
displayed, the Read authorization password input screen
is displayed.
8. Firmware Version Information
If one of keys 0 to 9 is pressed while the Read authoriza- Press and hold the [Side1] key while turning the transceiver
tion password input screen is displayed, the pressed num- power ON and then keep pressing and holding the [Side1]
ber is displayed on the LCD. key, the firmware version information appears on the LCD.
Each press of the key shifts the display in order to the left.
When you enter the password and press the [ ] or [ ]
key, “CLONE MODE” is displayed if the entered pass-
*
word is correct. If the password is incorrect, “CLONE
LOCK” is redisplayed.
• How to enter the password using the [ ] and [ ]
keys (K, K3 models);
If the [ ]/[ ] key is pressed while "CLONE LOCK" is
displayed, the Read authorization password input screen
is displayed.
If the [ ] key or [ ] key is pressed while the Read
authorization password input screen is displayed, the
number (0 to 9) blinks on the LCD. When you press the
[ ] key, the currently selected number is determined. If
you press the [ ] key after entering the password in this
procedure, “CLONE MODE” is displayed if the entered
password is correct. If the password is incorrect, “CLONE
LOCK” is redisplayed.
4. Power ON the target transceiver.
5. Connect the cloning cable (part No. E30-3325-05) to the
universal connectors on the source and target.
6. Press the [ ] key on the source while the source displays
“CLONE MODE”. The data of the source is sent to the
target. While the target is receiving the data, “PRO-
GRAM” is displayed. When cloning of data is completed,
the source displays “END”, and the target automatically
operates in the User mode. The target can then be oper-
ated by the same program as the source.
7. The other target can be continuously cloned. When the
[ ] key on the source is pressed while the source displays
“END”, the source displays “CLONE MODE”. Carry out
the operation in step 4 to 6.
5
NX-300
DISASSEMBLY FOR REPAIR
1. Precautions for Waterproof

• Do not remove the black sheet from the reverse side of
the transceiver (refer to the illustration right). Removal of
this sheet decreases the waterproof efficiency of the
transceiver and may cause malfunctions if water seeps
into the transceiver.
• The orange packing material on the reverse side of the
transceiver is important with respect to the waterproof
efficiency of the transceiver. Do not place stickers or other
materials on or around the packing material shown in the
figure, or on the reverse side of the battery pack. Doing so
will impair the waterproof efficiency of the transceiver and
may cause it to break down. Additionally, in order to
prevent damage to the packing material, do not allow it to
come in contact with foreign materials.
2. Precautions for Disassembly ■ Removing the TOP packing (G53-1762-02)

1. Pull on the TOP packing with your fingers to turn it back as
■ Removing the TX-RX unit from the chassis
shown in the figure z.
1. Remove the cord ASSY from the connector of the TX-RX 2. Pull the TOP packing to the left to remove the packing that
unit (CN900) z. is fit into the left groove of the chassis x.
2. Remove the PTT FPC from the connector of the TX-RX 3. Pull the TOP packing to the right to remove the packing
unit (CN901) x. that is fit into the right groove of the chassis c.
3. Remove the 14 screws c. 4. Remove the TOP packing v.
4. Anchor the screw hole of the TX-RX unit using the tip of a
pair of tweezers as shown in the figure. Then, lift the TX-
RX unit to remove it from the chassis v.
Cord ASSY
3
CN900
CN901 1
PTT FPC
1 2
2
4
TX-RX unit
3 3
3 3 3
3
4
3
6
NX-300
2. Mount the chassis onto the case x.
3. Precautions for Reassembly
■ Mounting the chassis onto the case Note:
1. Place the key top on the chassis. Then, fit the chassis After mounting the chassis onto the case, if the 18 key
tightly into the groove of the key top z. part on the key top or the Auxiliary (Orange) key part of the
VOL/CH packing gets stuck inside the case as shown in
Note: the figure, return it to the normal position using a soft
Confirm that the entire groove of the key top fits to the tipped item (e.g., finger) c.
chassis tightly. Prying it with a pointed metal tool such as forceps, may
damage the key top or packing.
18 key part
Auxiliary
(Orange) 3
key
7
NX-300
■ Installing lithium cell (W09-0971-05) ■ Forming the VOL/CH FPC, Cord ASSY and
1. Insert a lithium cell into one side of the socket (CN401). Universal connector FPC
2. Push the lithium cell with your fingers as shown in the Form the VOL/CH FPC, Cord ASSY and Universal
figure to insert the lithium cell into the socket. connector FPC as shown in the figure.
VOL/CH FPC
Control unit
CN401 Universal
Connector FPC
Cord ASSY
■ Affixing the keyboard ASSY (S79-0472-05) ■ Changing the channel selector from 16-channel
Affix the keyboard ASSY to the Control unit as shown in operation to free
the figure. 1. Remove the channel selector knob.
After affixing the keyboard ASSY to the Control unit, 2. Remove the circular nut.
confirm that the three positioning holes of the keyboard 3. Remove the mechanical stopper.
ASSY and the Control unit are not misaligned. 4. Reassemble the circular nut and channel selector knob
that were removed in steps 1 and 2, in their original
positions.
Keyboard
ASSY Channel selector knob Circular nut Mechanical stopper
(K29-9408-13) (N14-0844-04) (D32-0446-14)
Positioning holes Control unit
■ Inserting the Volume and Channel switch into

the chassis
Insert the volume and channel switch into the chassis
with the VOL/CH FPC formed as shown in the figure.
VOL/CH FPC
8
NX-300
CIRCUIT DESCRIPTION
1. Overview 2. Frequency Configuration

The NX-300 is a UHF portable transceiver designed to The receiver is a double-conversion superheterodyne
operate in the frequency range of 450 to 520MHz. The unit using the first intermediate frequency (IF) of 58.05MHz and
consists of receiver, transmitter, phase-locked loop (PLL) the second IF of 450kHz. Incoming signals from the antenna
frequency synthesizer, base band parts, power supply, and are mixed with the local signal from the PLL circuit to pro-
control circuits. duce the first IF of 58.05MHz. This is then mixed with the
57.6MHz second local oscillator output to produce the
450kHz second IF. The transmit signal frequency is gener-
ated by the PLL VCO, and modulated by the signal from the
DSP. It is then amplified and fed to the antenna.
ANT CF
TX/RX:450~520MHz 450kHz
1st MIX MCF SP

ANT RF MIX AF
SW AMP IF AMP AMP
Base band circuit

58.05MHz
19.2MHz x3
VC
TCXO
57.6MHz
391.95~ MIC
461.95MHz
PLL MIC
PA TX
VCO AMP
AMP AMP 450~520MHz
Fig. 1 Frequency configuration

3. Receiver System
3-1. RF Circuit 3-2. IF Circuit
An incoming RF signal from the antenna terminal is The first IF signal is passed through a four-pole monolithic
passed through the antenna switch (D606, 607, 709 ,711) crystal filter (XF700) to reject adjacent channel signals. The
and then the bandpass filter (L721, L722). The bandpass filter filtered first IF signal is amplified by the first IF amplifier
is adjusted by a variable capacitor. The input voltage to the (Q701) and then applied to the lF system IC (IC701). The IF
variable capacitor is regulated by the voltage output from the system IC provides a second mixer, AGC amplifier, and RSSI
D/A converter (IC703). The signal is amplified by an RF ampli- (Received Signal Strength Indicator).
fier (Q705), and passed through the bandpass filter (L713, The second mixer mixes the first IF signal with the
714, 715). The resulting signal is applied to the first mixer 57.6MHz of second local oscillator output and produces the
(Q703), where it is mixed with the first local oscillator signal second IF signal of 450kHz.
output from the frequency synthesizer to produce the first IF The second IF signal is passed through the ceramic filter
(58.05MHz). (CF700) to reject the adjacent channel signal. The filtered
second IF signal is amplified by the AGC amplifier.
The signal from the AGC amplifier is input to the ASIC
(IC108) through the ceramic filter (CF701) and operational
amplifier (IC700 and IC410).
ANT
D606,D607 RF AMP 1st MIX MCF IF AMP
L612~L614 D709,D711 L721,L722 Q705 L713~L715 Q703 XF700 Q701 CF701 IC700
ANT IC701
LPF BPF BPF BPF BPF
SW MIX, AGC
1st PLL OSC (PLL) 2nd OSC

X500 Q700 BPF
VC
x3 CF700
TCXO
19.2MHz
IC713
(2/2) IC413
IC410 IC704 IC707 IC703 IC408 IC409
IC108 INT. SP
SW VOL SW
ASIC
IC412
IC102 AMT
DSP EXT. SP
INAMT
EXAMT
Fig. 2 RF and IF circuit 9

NX-300
CIRCUIT DESCRIPTION
3-3. Audio Amplifier Circuit Q406
Audio processing (high-pass filter, low-pass filter, de-em- B
phasized and so on) at FM mode and decoding at NXDN Q407
mode are processed by DSP. The audio signal from IC108
INAMT
and IC102 goes through the amplifier (IC704). The signal then
goes through a mute switch (IC707), amplifier (IC713), elec-
tronic volume control (IC703), and AF amplifier (IC408). EXAMT
While busy, AMT becomes Low to turn IC707 on, and the IC409 VDD
signal is fed to the AF switch. While INAMT is High, the AF IC413 INT SP
AF signal
switch (IC409) selects the internal speaker, and the audio
from IC408
signal is fed to the internal audio power amplifier (IC413), and SHUT DOWN
output to the internal speaker. While EXAMT is High, the AF
switch (IC409) selects the external speaker, and the audio
VDD
signal is fed to the external audio power amplifier (IC412),
and output to the external speaker. The power supply for IC412 EXT SP
IC413 and IC412 is turned on while INAMT or EXAMT is High.
SHUT DOWN
The speaker is switched by the logic of the speaker
switching terminal SSW on the universal connector. When
the SP-MIC is not attached, SSW becomes High. IC108 de- Fig. 3 Audio amplifier circuit
tects the logic of SSW and activates either INAMT or EXAMT.
3-4. Squelch Circuit IC702(1/2) IC711(2/2) Q704 D705 IC711(1/2)

It amplifies the demodulated noise signal from IC108 after ASQAPC
filtering through the BPF circuit. Then, the amplified signal is DET LPF HPF AMP RECT AMP
converted to a DC signal by the detection circuit. The con- ASQDET
IC108
verted signal is fed back to IC108.
Fig. 4 Squelch circuit
4. Transmitter System
4-1. Audio Band Circuit 4-2. Base Band Circuit
The signal from the internal microphone goes through the The audio signal output from the base band circuit is con-
mute switch (Q5). When the SP-MIC is not attached, the verted to digital data with a sampling frequency of 48 kHz.
microphone switching terminal (MSW) on the universal con- This digital data is sent to the DSP (IC102), and voice signals
nector becomes High, and the mute switch (Q5) is turned on. of 300Hz or lower and frequencies of 3kHz or higher are cut
When the SP-MIC is attached, MSW is connected to GND off and an audio range of 300Hz to 3kHz is extracted. The
inside the SP-MIC. For this reason, Q5 is turned off, the inter- audio signal is then pre-emphasized in FM mode and synthe-
nal microphone is muted, and only the input of the external sized with the signals, such as QT and DQT, as required, and
microphone is supplied to the microphone amplifier. The sig- is then output from IC108. In Digital mode, the audio signal is
nal from the microphone goes through the mute switch converted to the 4-Level FSK base band signal and output
(Q707), and is amplified by IC716 (1/2) and limited by the AGC from IC108. The DTMF and MSK base band signals are also
circuit which is composed of D703, D704, Q705 and Q706. generated by the DSP and output by IC108.
LPF (IC705) works as a smoothing filter. The DAC (IC703)
assigns the base band signal to the VCO and VCTCXO (X500).
At this time, the level output according to the transmit carrier
is fine-adjusted according to each modulation method.
EXT. MIC IC102 DSP

IC716 IC710 IC705 IC705 IC710
INT. MIC Q5 Q707 (1/2) IC712 (1/2) IC706 (2/2) (1/2) (2/2) IC501 X500
IC108
SW SW AMP SW AMP LPF LPF LPF AMP IC703 AMP VCTCXO
ASIC
MM SCSW AMP VCO

Q4 AGC
IC504
D703,D704
MSW Q705,Q706
Fig. 5 Audio band and Base band circuit
10
NX-300
CIRCUIT DESCRIPTION
4-3. VOX 4-5. APC Circuit
IC716 (2/2) amplifies the audio signal captured in the mi- The APC circuit always monitors the current flowing
crophone. The signal is then converted into the DC voltage, through the RF power amplifier (Q606) and keeps a constant
rectified by D706. The DC voltage activates the ASIC (IC108), current. The voltage drop at R642, R645 and R647 is caused
and the VOX starts. by the current flowing through the RF power amplifier and
this voltage is applied to the differential amplifier (IC600 1/2).
4-4. Drive and Final Amplifier IC600 (2/2) compares the output voltage of IC600 (1/2) with
The signal from the T/R switch (D601 is on) is amplified by the reference voltage from IC108, and the output of IC600
the drive amplifier (Q601,Q602 and Q603) to 25~27dBm. The (2/2) controls the VGG of Q602, Q603 and Q606 to make the
output of the drive amplifier is amplified by the RF power both voltages the same. The change of power high/low is
amplifier (Q606) to 5.0W (1W when the power is low). The carried out by the change of the reference voltage. Q607,
RF power amplifier is MOS FET. The output of the RF power Q608 and Q610 are turned on and Q604 and Q605 are turned
amplifier is then passed through the harmonic filter (LPF) and off in transmit and the APC circuit is active.
antenna switch (D606, D607 are on) and applied to the
antenna terminal.
ANT
Q601 Q602 Q603 Q606 D606,D607
From
T/R SW Pre Drive Pre-Final Final ANT
LPF
(D601) Drive AMP AMP AMP SW
VDD VGG
R642
+B
R645
R647
IC600 IC600
REF (1/2) (2/2)
VOL
(IC108)
Fig. 6 Drive and final amplifier and APC circuit
5. PLL Frequency Synthesizer

5-1. VCTCXO (X500) 5-2. VCO
VCTCXO (X500) generates a reference frequency of There is a RX VCO and a TX VCO.
19.2MHz for the PLL frequency synthesizer. This reference The TX VCO (Q509) generates a transmit carrier and the
frequency is applied to pin 9 of the PLL IC (IC502) and con- RX VCO (Q508) generates a 1st local signal. For the VCO os-
nected to the IF circuit as a 2nd local signal through the cillation frequency, the transmit carrier is 450 to 520 MHz and
Tripler. The VCTCXO oscillation frequency is determined by the 1st local signal is 391.95 to 461.95MHz.
the DC voltage of the VC terminal. The VC voltage is fixed to The VCO oscillation frequency is determined by one sys-
1.65V by R500 and R501, and supplied to the VC terminal tem of operation switching terminal "T/R" and two systems of
through IC501. The modulation signal is also fed to the VC voltage control terminals "C/V" and "V-assist".
terminal through IC501 The operation switching terminal, "T/R", is controlled by
The frequency adjustment is achieved by switching the the control line (/T_R) output from the ASIC (IC108). When
ratio of the dividing frequency that is not adjusted by the DC the /T_R logic is low, the VCO outputs the transmit carrier
voltage impressed to the VC. The resolution of the adjusting and when it is high, it outputs a 1st local receive signal.
frequency is approximately 4Hz. The voltage control terminals, "CV" and "V-assist", are con-
trolled by the PLL IC (IC502) and ASIC (IC108) and the output
frequency changes continuously according to the applied
voltage. For the modulation input terminal, "VCO_MOD", the
output frequency changes according to the applied voltage.
This is used to modulate the VCO output. "VCO_MOD" works
only when "/T_R" is low.
11
NX-300
CIRCUIT DESCRIPTION
5-3. PLL IC (IC502) The desired frequency is set for the PLL IC by the ASIC
The PLL IC compares the differences in phases of the (IC108) through the 3-line "SDO1", "SCK1", "/PCS_RF" serial
VCO oscillation frequency and the VCTCXO reference bus. Whether the PLL IC is locked or not is monitored by the
frequency, returns the difference to the VCO CV terminal and ASIC through the “PLD” signal line. If the VCO is not the
realizes the "Phase Locked Loop" for the return control. This desired frequency (unlock), the "PLD" logic is low.
allows the VCO oscillation frequency to accurately match
(lock) the desired frequency. 5-4. Local Switch (D600, D601)
When the frequency is controlled by the PLL, the fre- The connection destination of the signal output from the
quency convergence time increases as the frequency differ- buffer amplifier (Q600) is changed with the diode switch
ence increases when the set frequency is changed. To (D601) that is controlled by the transmission power supply,
supplement this, the ASIC is used before control by the PLL 50T, and the diode switch (D600) that is controlled by the
IC to bring the VCO oscillation frequency close to the desired receive power supply, 50R. If the 50T logic is high, it is con-
frequency. As a result, the VCO CV voltage does not change nected to a send-side pre-drive (Q601). If the 50T logic is low,
and is always stable at approximately 2.5V. it is connected to a receive-side mixer (Q703).
Q508,Q509
X500 D506,D507,D510,D511
19.2MHz IC502 D514~D517,D519 Q512 Q600 D600,D601
VC PLL Loop BUFF BUFF T/R
VCO to TX stage
TCXO IC Filter AMP AMP SW
SDO1 Q504
50T
50R
to 1st Mixer
SCK1 50C
/PCS_RF CV
BUFF
VCO_MOD 50C
AMP
Q505
IC504(1/2)
150C
Q503
Ripple
Filter
IC503
ASSIST
LPF
Fig. 7 PLL block diagram
6. Control Circuit 6-1. ASIC

The ASIC (IC108) is a 32-bit RISC processor, equipped
The control circuit consists of the ASIC (IC108) and its pe-
with peripheral function and ADC/DAC.
ripheral circuits. IC108 mainly performs the following;
This ASIC operates at 18.432MHz clock and 3.3V /1.5V
1) Switching between transmission and reception by PTT
DC. It controls the flash memory, SRAM, DSP, the receive
signal input.
circuit, the transmitter circuit, the control circuit, and the dis-
2) Reading system, zone, frequency, and program data
play circuit and transfers data to or from an external device.
from the memory circuit.
3) Sending frequency program data to the PLL.
4) Controlling squelch on/off by the DC voltage from the
squelch circuit.
5) Controlling the audio mute circuit by decode data input.
12
NX-300
CIRCUIT DESCRIPTION
6-2. Memory Circuit 6-6. DSP
The memory circuit consists of the ASIC (IC108) and the The DSP circuit consists of a DSP (IC102) and processes
SRAM(IC103) and flash memory (IC101). The flash memory the base band signal. The DSP operates on an external clock
has capacity of 32M-bit that contains the transceiver control of 18.432MHz (the same as the IC108), the I/O section oper-
program for the ASIC and stores the data. It also stores the ates at 3.3V and the core section operates at 1.5V. The DSP
data for transceiver channels and operating parameter that carries out the following processes:
are written by the FPU. This program can be easily written • 4 Level FSK processing
from external devices. The SRAM has capacity of 1M-bit that • Analog FM pre-emphasis/de-emphasis
contains work area and data area. • Vocoder processing between audio codec and modula-
tion/demodulation
■ Flash memory • CAI processing, such as error correction encoding
Note: The flash memory stores the data that is written by the • QT/DQT encoding/decoding
FPU (KPG-111D), tuning data (Deviation, Squelch, etc.) ,and • LTR encoding/decoding
firmware program (User mode, Test mode, Tuning mode, • DTMF encoding/decoding
etc.). This data must be rewritten when replacing the flash • MSK encoding/decoding
memory. • 2-tone encoding/decoding
• Compressor/expander processing
■ SRAM (Static memory) • Voice scrambler processing
Note: The SRAM has temporary data area and work area. • Transmit/receive audio filtering processing
When the power supply is off, it is backed up by an internal • Microphone amplifier AGC processing
secondary lithium battery. Therefore, the saved data is not • Audio mute processing
lost. • Modulation level processing
■ Real-time clock
7. Power Supply Circuit
The clock function is based on real-time clock IC (IC106).
When the power supply is off, it is backed up by an internal The battery voltage (+B) is provided from the battery
secondary lithium battery terminal on the TX/RX unit (X57). The battery voltage passes
through the 2.5A fuse (F900), and goes to the RF final ampli-
fier, AVR ICs (IC902, IC903), and Control unit (X53-426).
6-3. LCD
In the control unit, +B is connected to the DC/DC (IC407),
The LCD is controlled using the bus lines on the connector
AVR ICs (IC411, IC708, IC416), and voltage detector IC
(CN1) of the Control unit (X53-426). It corrects the LCD con-
(IC414). The voltage detector watches the battery voltage.
trast voltage using IC1.
If the battery voltage is 5.6V or higher, the detector outputs
High. While the output of IC414 is High, IC416 and Q409
6-4. Key Detection Circuit
provide 3.1V (31BU) to the backup-section.
Keys are detected using the key scan circuit in IC108. The
When the VOL SW is turned on, SB1 becomes high (bat-
/KEYI* signals that are normally pulled down go high when
tery voltage). The DC/DC (IC407) operates if both SB1 and
any key is pressed.
the output of the detector are high. IC407 outputs 3.8V and it
activates IC404 (33M), IC405 (15M), and IC406 (33A). As a
6-5. Low Battery Warning result, the ASIC and DSP operate.
The battery voltage is divided using R444 and R445 and is The SBC signal becomes High after the ASIC operates,
detected by the ASIC (IC108). When the battery voltage falls IC708 (5A), Q403 on the Control unit (SB2) and Q901 on the
below the voltage set by the Low battery warning adjust- TX-RX unit (SB3) are turned on. IC901 and IC903 operate by
ment, the red LED blinks to notify the operator that it is time turning on these AVR ICs and FET switches.
to replace the battery. If the battery voltage falls even more The 5UC signal becomes High when an option is installed
(approx. 5.8V), a beep sounds and transmission stops. on the universal connector. Then IC411 (50U) operates.
When the /SAVE signal becomes High, IC902 (50C) oper-
Low battery warning Battery condition ates. The output of IC902 is connected to three FET switches
The red LED blinks during The battery voltage is low but (Q902, Q903, Q905). When the SBC signal becomes High,
transmission. the transceiver is still usable. IC903 (33C) operates. The FET switches are controlled by the
CPU. Q905 (50T) is turned on in transmit mode. Q902 (50R)
The red LED blinks and the The battery voltage is low
and Q903 (50IF) are turned on in receive mode.
warning tone beeps while and the transceiver is not When the VOL SW is turned off the /PSW signal
the PTT switch is pressed. usable to make calls. becomes Low. After detecting the /PSW signal, the ASIC
changes SBC signal to Low. Then the power supplies except
IC416 (31BU) stop.
13
NX-300
CIRCUIT DESCRIPTION
TX-RX unit (X57)
8. Signaling Circuit
F900
+B RF Final AMP 8-1. Encode (QT/DQT/LTR/DTMF/2-tone/MSK)
APC
2.5A
IC902 50C Each signaling data signal of QT, DQT, LTR, DTMF, 2-tone
/SAVE VCO and MSK is generated by the DSP circuit, superposed on a
AVR
/5TC
Q905 50T
TX circuit
modulation signal and output from IC108. The modulation
50T SW balance of the QT/DQT/LTR signal is adjusted by the D/A
converter(IC703) and the resulting signal is routed to the
Q902 50R
5RC
50R SW
RX circuit modulation input of the VCO and VCXO (X500). Each devia-
tion of the TX QT, DQT, LTR, DTMF and MSK tone is adjusted
Q903 50IF by changing the output level of IC108 and the resulting signal
IFC IF circuit
50IF SW is routed to the VCO and VCXO. The RX DTMF tone is routed
to the receive audio signal system, and is output from the
IC903 33C
SBC
AVR IC
PLL, VCTCXO speaker.
Q901 SB3 8-2. Decode (QT/DQT/LTR/DTMF/2-tone/MSK)

TX/Busy LED
SB3 SW The audio signal is removed from the FM detection signal
IC901 150C
Assist, Tune sent to the DSP circuit and the resulting signal is decoded.
DC/DC
CN900
9. Compander Circuit
Control unit (X53) The term “compander” means compressor and expander.
The compander reduces noise by utilizing a compressor and
CN404
an expander. The transceiver contains a DSP(IC102) to per-
IC411 50U form this operation. The transceiver compander can be
5UC Universal
AVR IC turned on or off using the FPU.
Q403 SB2 BackLight
SBC Key Light
SB2 SW
IC708 5A
Option
AVR IC
IC403 -10V
LCD Bias
DC/DC
IC416
Q409 31BU
AVR IC SRAM, RTC
31BU
IC407
IC404 33M ASIC, DSP I/O,
DC/DC
AVR Flach, LCD DRV
IC414 IC405 15M

ASIC, DSP core
Detect AVR
IC406 33A ASIC Analog,

AVR Audio
SB1 Q402 /PSW IC108

VOL SW Lvl Conv ASIC
Q408 Q401 /BINT

AND Lvl Conv
D408 D412
SBC
OR OR
Fig. 8 Power supply circuit
14
NX-300
COMPONENTS DESCRIPTION
Control unit (X53-4260-XX) Ref. No. Part Name Description
Ref. No. Part Name Description Q403 Transistor SB2 switch
IC1 IC LCD contrast Q404 FET SB2 switch control

IC101 IC FLASH ROM Q405 FET AF AMP switch
IC102 IC DSP Q406,407 Transistor Voltage regulator (AF AMP)

IC103 IC SRAM Q408,409 Transistor DC switch
IC104 IC 2 input AND gate Q410 FET DC switch

IC105 IC Reset Q411 FET Level converter
IC106 IC RTC Q412 FET DC switch

IC107 IC Buffer Q413~415 Transistor DC switch
IC108 IC ASIC Q701 Transistor OPT switch

IC109 IC 2 input AND gate Q702 FET Tone switch
IC401,402 IC Bus switch Q703 FET W/N noise switch

IC403 IC Voltage doubling inverter Q704 Transistor SQL noise AMP
IC404 IC Voltage regulator (33M) Q705,706 Transistor MIC AGC

IC405 IC Voltage regulator (15M) Q707 FET MIC mute
IC406 IC Voltage regulator (33A) D1,2 LED 12key backlight

IC407 IC DC/DC converter D3,4 LED LCD backlight
IC408 IC AF AMP D5,6 LED 12key backlight

IC409 IC AF switch D7,8 LED LCD backlight
IC410 IC IF AMP D9,10 LED 12key backlight

IC411 IC Voltage regulator (50U) D11 Diode LCD backlight switch
IC412,413 IC Audio AMP D12~16 Diode Reverse current prevention

IC414 IC Reset D17~19 Zener diode Surge absorption
IC415 IC 2 input AND gate D20 Zener diode PTT RF OPT control
IC416 IC Voltage regulator D21 Zener diode EMC MSW SSW control
IC417,418 IC Dual bus buffer D22 Diode RXD control

IC701 IC I/O control D23 Diode TXD control
IC702 IC APC LPF D101 Diode 12key backlight switch

IC703 IC D/A converter D102 Diode Reverse current prevention
IC704 IC RX AF LPF D401~404 Diode 12key control

IC705 IC Modulation LPF D405,406 Diode DC/DC converter
IC706 IC MIC AMP D407 Diode Reverse current prevention

IC707 IC RX AF switch D408 Diode DC/DC converter control
IC708 IC Voltage regulator (5A) D409,410 Diode SP control

IC709 IC Sidetone mute D411 Diode RTC BATT control
IC710 IC MOD/MIC summing AMP D412 Diode DC switch control

IC711 IC SQL BPF/SQL DC AMP D413 Diode RTC BATT control
IC712 IC MIC switch D414 Diode TX LED switch

IC713 IC 1.65V REF/RX summing AMP D415 Diode RX LED switch
IC714 IC OPT switch D416 Diode 33M control

IC715,716 IC VOX AMP D417 Diode 33A control
Q1,2 Transistor LCD backlight switch D701 Diode 5A switch

Q3 FET LCD backlight switch D702 Diode PLD control
Q4 FET MIC shift control D703,704 Diode Detector

Q5 FET MIC shift switch D705 Diode Noise detector
Q101,102 Transistor 12key backlight switch D706 Diode Detector

Q103 FET 12key backlight switch D707 Diode VOX
Q401,402 FET Level converter
15
NX-300
COMPONENTS DESCRIPTION
TX-RX unit (X57-7370-10) Ref. No. Part Name Description
Ref. No. Part Name Description D506,507, Variable Frequency control
D510,511 capacitance diode
IC404 IC OP AMP (RSSI/VAGC)
D514~517 Variable Frequency control
IC500 IC Temperature sensor
capacitance diode
IC501 IC DC AMP for TCXO MOD D518 Diode Ripple filter
IC502 IC PLL IC D519 Variable TX modulation
IC503 IC DC AMP for VCO tune capacitance diode
IC504 IC OP AMP (VCO MOD/APC) D600,601 Diode Local switch
IC600 IC Auto power control D604 Zener diode APC switch
IC700 IC Buffer D605 Zener diode APC protect
IC701 IC FM IC D606,607 Diode Antenna switch
IC702,703 IC DC AMP for BPF D700 Diode Ripple filter
IC900 IC 50T control D702~704 Variable Vari-cap tune
IC901 IC DC/DC converter capacitance diode
IC902 IC Voltage regulator (50C) D705 Diode RF AGC
IC903 IC Voltage regulator (33C) D706,708 Variable Vari-cap tune

capacitance diode
Q503 Transistor Ripple filter
D709 Diode Antenna switch
Q504 FET Buffer AMP
D710 Variable Vari-cap tune
Q505 Transistor Buffer AMP
capacitance diode
Q507 Transistor Ripple filter D711 Diode Antenna switch
Q508,509 FET VCO oscillation D900 LED TX/RX LED
Q510,511 FET T/R switch D901 Diode Reverse protection
Q512,600 Transistor Buffer AMP D902 Diode 50T control
Q601 Transistor RF AMP
Q602 FET RF AMP
Q603 FET RF drive AMP
Q604 Transistor APC switch
Q605 FET APC switch
Q606 FET RF final AMP
Q608 FET APC switch
Q700 Transistor 2nd Local buffer AMP
Q701 Transistor IF AMP
Q703 FET Mixer
Q704 Transistor Ripple filter
Q705 FET RF AMP
Q706 FET RF AGC
Q900 Transistor TX/RX LED switch
Q901 FET SB3 switch
Q902 FET 50R switch
Q903 FET 50IF switch
Q904 FET DC/DC converter switch
Q905 Transistor 50T switch
D501 Diode Ripple filter
D505 Diode Bypass diode
16
NX-300
PARTS LIST
∗ New Parts. indicates safety critical components. L: Scandinavia K: USA P: Canada
Parts without Parts No. are not supplied. Y: PX (Far East, Hawaii) T: England E: Europe
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Y: AAFES (Europe) X: Australia M: Other Areas
Teile ohne Parts No. werden nicht geliefert.
NX-300 (Y50-6120-XX)
CONTROL UNIT (X53-4260-XX)
New New
Ref. No. Address parts Parts No. Description Destination Ref. No. Address parts Parts No. Description Destination
59 1A ∗ K29-9406-03 BUTTON KNOB(SIDE KEY)
NX-300 60 1B ∗ K29-9407-03 KNOB(VOL)
1 1B ∗ A02-4002-13 PLASTIC CABINET(6KEY) K
2 1A ∗ A02-4003-13 PLASTIC CABINET(18KEY) K3 61 1B ∗ K29-9408-13 KNOB(CH)
3 2B ∗ A62-1156-02 PANEL(TOP)
4 1B ∗ B09-0712-03 CAP ACCESSORY A 1B,1D ∗ N08-0564-04 DRESSED SCREW ACCESSORY
5 1A ∗ B11-1853-24 FILTER(LCD) B 3B N09-2426-14 HEXAGON HEAD SCREW(BATT -)
C 3A N09-2440-15 SPECIAL SCREW(CASE)
6 1A ∗ B11-1854-02 ILLUMINATION GUIDE(LCD) D 2A,2B ∗ N09-6549-04 STEPPED SCREW(FG-SP HOLDER)
7 3B ∗ B11-1855-04 ILLUMINATION GUIDE(TX/BUSY) E 2B,3A ∗ N09-6554-05 PAN HEAD SCREW(ANT/OP BOARD)
8 1A ∗ B38-0923-05 LCD ASSY
9 1A ∗ B42-7296-04 STICKER F 2B ∗ N14-0844-04 CIRCULAR NUT(VOL,CH)
10 1B ∗ B43-1606-04 BADGE G 1C N30-3008-60 PAN HEAD MACHINE SCREW(BELT CLIP)
H 1A,2A,2B N83-2005-48 PAN HEAD TAPTITE SCREW(PCB)
11 2D ∗ B62-2014-00 INSTRUCTION MANUAL
12 2B ∗ D32-0446-14 STOPPER(16CH) 64 1A ∗ S79-0472-05 KEYBOARD ASSY(12KEY) K3
14 3A ∗ E29-1221-04 RELAY HARDWARE(VCO-CHASSIS) 65 2A T07-0755-15 SPEAKER
15 2A ∗ E29-1220-04 RELAY HARDWARE(VCO-PCB) 66 2A T91-0575-05 MIC ELEMENT
16 3B ∗ E58-0532-05 RECTANGULAR RECEPTACLE(SP/MIC)
67 2A W09-0971-05 LITHIUM CELL
17 3B ∗ E72-0425-03 TERMINAL BLOCK 68 3A ∗ X41-3710-10 SWITCH UNIT(PTT FPC)
18 3A ∗ F07-1931-04 COVER(OP BOARD) 69 2B ∗ X41-3720-10 SWITCH UNIT(6KEY FPC)
19 2A ∗ G02-1836-13 EARTH SPRING(SP) 70 2A ∗ X42-3340-10 CORD ASSY(50PIN FPC)
20 1A ∗ G10-1373-04 FIBROUS SHEET(SP) 72 2B ∗ X60-3860-10 TERMINAL ASSY(SMA)
21 2B ∗ G10-1384-04 FIBROUS SHEET(TOP PANEL)
CONTROL UNIT (X53-4260-XX) -10 :K -11 :K3
23 2A G11-4272-14 RUBBER CUSHION(SP)
24 3A G11-4331-04 SHEET(AIR) D1 -10 B30-2215-05 LED K3
25 3A ∗ G11-4428-04 SHEET(PTT) D3 ,4 B30-2215-05 LED K
26 3A ∗ G11-4429-04 RUBBER SHEET(FET) D7 ,8 B30-2215-05 LED K
27 3A ∗ G11-4440-04 SHEET(AIR)
C1 CK73HB1A104K CHIP C 0.10UF K
29 2A ∗ G11-4458-14 SHEET(SP) C2 -6 CK73GB1E105K CHIP C 1.0UF K
30 2A ∗ G11-4459-04 SHEET(TX-RX PCB) C7 ,8 CK73HB1A104K CHIP C 0.10UF K
31 2A G13-2129-14 CUSHION(TX-RX PCB) C10 CK73HB1A104K CHIP C 0.10UF K
33 2A ∗ G13-2258-04 CUSHION(50PIN FPC) C11 CK73HB0J105K CHIP C 1.0UF K
34 3B ∗ G53-1762-02 PACKING(TOP)
C12 -15 CK73HB1H471K CHIP C 470PF K
35 3B ∗ G53-1763-03 PACKING(TERMINAL BLOCK) C16 ,17 CC73HCH1H101J CHIP C 100PF J
36 3A ∗ G53-1764-03 PACKING(OP BOARD) C23 -27 CK73HB1H102K CHIP C 1000PF K
37 1B ∗ G53-1765-11 PACKING(6KEY) K C28 -34 CC73HCH1H101J CHIP C 100PF J
38 1A ∗ G53-1766-11 PACKING(18KEY) K3 C35 CK73HB1H102K CHIP C 1000PF K
39 2B ∗ G53-1768-04 PACKING(VOL,CH O-RING)
C36 CK73HB1E682K CHIP C 6800PF K
40 1B ∗ G53-1769-04 PACKING(CAP) C37 CK73HB1H102K CHIP C 1000PF K
41 2B G53-1792-04 PACKING(SMA O-RING) C38 CC73HCH1H101J CHIP C 100PF J
42 2A ∗ J19-5505-11 HOLDER(FG-SP) C40 CC73HCH1H221J CHIP C 220PF J
43 2B ∗ J19-5506-03 HOLDER(VOL,CH) C41 CC73HCH1H101J CHIP C 100PF J
44 2A ∗ J19-5507-02 HOLDER(OP BOARD)
C101-104 CK73HB1A104K CHIP C 0.10UF K
45 2B ∗ J21-8579-04 MOUNTING HARDWARE(FG-SP HOLDER) C105 CK73HB0J105K CHIP C 1.0UF K
46 1C J29-0730-05 BELT CLIP ACCESSORY C106 CK73HB1E103K CHIP C 0.010UF K
47 2B ∗ J30-1296-04 SPACER(VOL) C107 CK73HB1A104K CHIP C 0.10UF K K
48 2B ∗ J87-0006-05 FPC(LEAD FREE/VOL,CH) C107,108 CK73HB1A104K CHIP C 0.10UF K K3
49 3B ∗ J87-0007-05 FPC(LEAD FREE/UNIVERSAL)
C109,110 CK73HB1H102K CHIP C 1000PF K
50 2B J99-0390-04 ADHESIVE SHEET(6KEY FPC) C111-113 CK73HB1A104K CHIP C 0.10UF K
52 3A ∗ J99-0711-04 ADHESIVE SHEET(PTT FPC) C114 CK73HB0J105K CHIP C 1.0UF K K3
53 2B ∗ J99-0712-14 ADHESIVE SHEET(6KEY FPC) C115 CK73HB1H471K CHIP C 470PF K K3
54 1A ∗ J99-0714-04 ADHESIVE SHEET(LCD) C116,117 CK73HB1A104K CHIP C 0.10UF K
55 3B ∗ J99-0715-08 ADHESIVE SHEET(UNIVERSAL)
C118,119 CK73HB0J105K CHIP C 1.0UF K
56 3B ∗ J99-0725-04 ADHESIVE SHEET(TERMINAL BLOCK) C120,121 CK73HB1A104K CHIP C 0.10UF K
57 3A ∗ K25-2001-03 PUSH KNOB(PTT) C122-124 CK73HB1E103K CHIP C 0.010UF K
58 1A ∗ K29-9405-03 KNOB(PTT) C130 CK73HB1E103K CHIP C 0.010UF K
17
NX-300
PARTS LIST
New New
C131 CK73HB1A104K CHIP C 0.10UF K C466 CK73HB1E682K CHIP C 6800PF K

C467,468 CK73HB1E103K CHIP C 0.010UF K
C133 CS77CP0J100M CHIP TNTL 10UF 6.3WV
C134 CK73HB1E103K CHIP C 0.010UF K C469,470 CK73HB1H102K CHIP C 1000PF K
C135 CK73HB1H102K CHIP C 1000PF K C701 CK73HB1A104K CHIP C 0.10UF K
C136 CK73HB1E103K CHIP C 0.010UF K C703 CK73GB0J475K CHIP C 4.7UF K
C137 CK73GB1E105K CHIP C 1.0UF K C704,705 CK73HB1A104K CHIP C 0.10UF K
C706 CC73HCH1H680J CHIP C 68PF J
C141 CC73HCH1H101J CHIP C 100PF J C707 CC73HCH1H270J CHIP C 27PF J
C142 CS77CP0J100M CHIP TNTL 10UF 6.3WV C708 CK73HB1A104K CHIP C 0.10UF K
C143 CK73HB1E103K CHIP C 0.010UF K C709 CK73HB0J105K CHIP C 1.0UF K
C144 CK73GB1E105K CHIP C 1.0UF K C710 CK73HB1E103K CHIP C 0.010UF K
C149 CK73HB1E103K CHIP C 0.010UF K C712 CK73HB1E103K CHIP C 0.010UF K
C150 CK73GB1E105K CHIP C 1.0UF K C713 CK73HB1H332K CHIP C 3300PF K
C151-155 CK73HB1A104K CHIP C 0.10UF K C714 CK73HB1H122K CHIP C 1200PF K
C156,157 CK73HB1H102K CHIP C 1000PF K C715 CK73HB1A104K CHIP C 0.10UF K
C716 CK73HB1H681K CHIP C 680PF K
C158 CK73HB1E103K CHIP C 0.010UF K
C159 CK73HB1A104K CHIP C 0.10UF K C717 CK73HB1E103K CHIP C 0.010UF K
C160,161 CK73HB1E682K CHIP C 6800PF K C718 CK73HB1H152K CHIP C 1500PF K
C401,402 CK73HB1A104K CHIP C 0.10UF K C719 CK73HB1A104K CHIP C 0.10UF K
C403-405 CS77AP1C2R2M CHIP TNTL 2.2UF 16WV C720 CK73HB1E103K CHIP C 0.010UF K
C406 CK73HB0J105K CHIP C 1.0UF K
C407,408 CK73HB1H102K CHIP C 1000PF K C722 CK73HB1E103K CHIP C 0.010UF K
C409-412 CK73HB0J105K CHIP C 1.0UF K C723 CK73HB1A104K CHIP C 0.10UF K
C413 ∗ CK73FB1A106K CHIP C 10UF K C724 CK73HB1E103K CHIP C 0.010UF K
C414 CK73HB0J105K CHIP C 1.0UF K C725 CC73HCH1E181J CHIP C 180PF J
C726,727 CK73HB1A104K CHIP C 0.10UF K
C415 CS77AP1A100M CHIP TNTL 10UF 10WV
C416 ∗ CK73FB1A106K CHIP C 10UF K C728 CK73HB1H331K CHIP C 330PF K
C417 CC73HCH1H221J CHIP C 220PF J C730 CK73HB1H331K CHIP C 330PF K
C418 CK73HB1E103K CHIP C 0.010UF K C731,732 CK73HB1E103K CHIP C 0.010UF K
C419 ∗ CK73FB1E475K CHIP C 4.7UF K C734 CK73HB1H102K CHIP C 1000PF K
C421 CK73HB1E682K CHIP C 6800PF K C736,737 CK73HB1A104K CHIP C 0.10UF K
C422 CC73HCH1H100C CHIP C 10PF C C738 CK73HB1H102K CHIP C 1000PF K
C424,425 CK73HB1A104K CHIP C 0.10UF K C739 CK73HB1E682K CHIP C 6800PF K
C427 CK73HB1E103K CHIP C 0.010UF K C740 CK73HB1H102K CHIP C 1000PF K
C742 CK73GB1E105K CHIP C 1.0UF K
C428 CC73HCH1H030C CHIP C 3.0PF C
C429,430 CK73HB1A104K CHIP C 0.10UF K C743 CK73HB0J105K CHIP C 1.0UF K
C431 ∗ CK73FB1A106K CHIP C 10UF K C744-746 CK73HB1E103K CHIP C 0.010UF K
C432 CK73HB1E103K CHIP C 0.010UF K C747,748 CK73HB1A104K CHIP C 0.10UF K
C433 ∗ CK73FB1A106K CHIP C 10UF K C749,750 CC73HCH1H470J CHIP C 47PF J
C435-438 CK73HB1A224K CHIP C 0.22UF K C752,753 CC73HCH1H101J CHIP C 100PF J
C439,440 CK73HB1A104K CHIP C 0.10UF K C755 CC73HCH1H470J CHIP C 47PF J
C441 CK73GB1E105K CHIP C 1.0UF K C756 CK73HB1A104K CHIP C 0.10UF K
C442 CK73HB1H471K CHIP C 470PF K C757,758 CK73GB0J475K CHIP C 4.7UF K
C445 CK73HB1H102K CHIP C 1000PF K C761 CC73HCH1H100D CHIP C 10PF D
C446 CK73GB1E105K CHIP C 1.0UF K C762 CK73HB1A104K CHIP C 0.10UF K
C447 CK73HB1H102K CHIP C 1000PF K C763 CK73HB1E103K CHIP C 0.010UF K
C448-450 CK73HB0J105K CHIP C 1.0UF K C764 CK73HB1H102K CHIP C 1000PF K
C451-453 CK73HB1E103K CHIP C 0.010UF K
C454 CK73GB1E105K CHIP C 1.0UF K C768 CK73HB1H102K CHIP C 1000PF K
C455-457 CK73HB1H471K CHIP C 470PF K C771 CK73HB1A224K CHIP C 0.22UF K
C460 CK73HB1E682K CHIP C 6800PF K C775 CC73HCH1H470J CHIP C 47PF J
C461-463 CK73HB1H471K CHIP C 470PF K
C464 CK73HB1E103K CHIP C 0.010UF K C778 CK73HB0J105K CHIP C 1.0UF K
18
NX-300
PARTS LIST
New New
C780 CK73HB1A224K CHIP C 0.22UF K R16 RK73HB1J331J CHIP R 330 J 1/16W

C781,782 CK73HB0J105K CHIP C 1.0UF K R17 RK73HB1J000J CHIP R 0.0 J 1/16W
R18 RK73HB1J822J CHIP R 8.2K J 1/16W
C786 CK73HB1E103K CHIP C 0.010UF K R19 RK73HB1J471J CHIP R 470 J 1/16W
C787 CK73HB0J105K CHIP C 1.0UF K R20 RK73HB1J102J CHIP R 1.0K J 1/16W
C788 CC73HCH1H150J CHIP C 15PF J R21 RK73HB1J122J CHIP R 1.2K J 1/16W
C789 CC73HCH1H680J CHIP C 68PF J R22 -24 RK73HB1J102J CHIP R 1.0K J 1/16W
C791 CK73HB1A393K CHIP C 0.039UF K R26 RK73HB1J102J CHIP R 1.0K J 1/16W
C792 CK73HB0J105K CHIP C 1.0UF K R27 RK73HB1J104J CHIP R 100K J 1/16W
C793,794 CK73HB1A104K CHIP C 0.10UF K R28 ,29 RK73HB1J102J CHIP R 1.0K J 1/16W
C795 CK73HB1E103K CHIP C 0.010UF K R30 RK73HB1J101J CHIP R 100 J 1/16W
C797 CK73HB0J105K CHIP C 1.0UF K R32 -35 RK73HB1J101J CHIP R 100 J 1/16W
C798 CS77AP1A100M CHIP TNTL 10UF 10WV R40 RK73HB1J000J CHIP R 0.0 J 1/16W
C799 CK73HB1A104K CHIP C 0.10UF K R101,102 RK73HB1J474J CHIP R 470K J 1/16W
C800 CK73HB1H152K CHIP C 1500PF K R103 RK73HB1J102J CHIP R 1.0K J 1/16W
C801 CK73HB1C223K CHIP C 0.022UF K
R105 RK73HB1J104J CHIP R 100K J 1/16W
C802 CK73HB1E103K CHIP C 0.010UF K R106 RK73HB1J472J CHIP R 4.7K J 1/16W K3
C803 CK73HB1H102K CHIP C 1000PF K R107 RK73HB1J104J CHIP R 100K J 1/16W
C804 CC73HCH1H470J CHIP C 47PF J R108 RK73HB1J474J CHIP R 470K J 1/16W K3
R110,111 RK73HB1J104J CHIP R 100K J 1/16W
CN1 ∗ E40-6755-05 FLAT CABLE CONNECTOR
CN22 ∗ E23-1325-05 TERMINAL R112 RK73HB1J000J CHIP R 0.0 J 1/16W K3
CN23 ∗ E40-6758-05 PIN ASSY R113 RK73HB1J104J CHIP R 100K J 1/16W
CN24 ∗ E23-1325-05 TERMINAL R114 RK73HB1J331J CHIP R 330 J 1/16W K3
CN404 ∗ E40-6421-15 PIN ASSY
CN405 ∗ E40-6754-05 FLAT CABLE CONNECTOR R117 RK73HB1J000J CHIP R 0.0 J 1/16W K3
CN701 E40-6586-05 SOCKET FOR PIN ASSY R118 RK73HB1J473J CHIP R 47K J 1/16W
F701 F53-0360-05 FUSE(0.25A) R121-123 RK73HB1J104J CHIP R 100K J 1/16W
CN401 J19-5386-05 HOLDER(LITHIUM CELL) R126 RK73HB1J101J CHIP R 100 J 1/16W

R127,128 RK73HB1J000J CHIP R 0.0 J 1/16W
L1 ,2 L92-0408-05 CHIP FERRITE R129-131 RK73HB1J101J CHIP R 100 J 1/16W
L3 L92-0140-05 CHIP FERRITE R132,133 RK73HB1J104J CHIP R 100K J 1/16W
L4 -7 L92-0408-05 CHIP FERRITE R135-137 RK73HB1J104J CHIP R 100K J 1/16W
L8 L92-0140-05 CHIP FERRITE
L101,102 L92-0408-05 CHIP FERRITE R138 RK73HB1J473J CHIP R 47K J 1/16W
L401 ∗ L33-1496-05 SMALL FIXED INDUCTOR R140 RK73HB1J000J CHIP R 0.0 J 1/16W
L402 L92-0467-05 CHIP FERRITE R141-143 RK73HB1J104J CHIP R 100K J 1/16W
L403 ∗ L92-0466-05 CHIP FERRITE R144 RK73HB1J471J CHIP R 470 J 1/16W
L409,410 L92-0467-05 CHIP FERRITE
L701 L92-0140-05 CHIP FERRITE R145-147 RK73HB1J104J CHIP R 100K J 1/16W
R148 RK73HB1J151J CHIP R 150 J 1/16W
L702 L92-0162-05 BEADS CORE R149 RK73HB1J000J CHIP R 0.0 J 1/16W
L704-709 L92-0162-05 BEADS CORE R150 RK73HB1J102J CHIP R 1.0K J 1/16W
L710-712 L92-0444-05 CHIP FERRITE R153,154 RK73HB1J104J CHIP R 100K J 1/16W
L713 L92-0163-05 BEADS CORE
L714-717 L92-0444-05 CHIP FERRITE R155 RK73HB1J473J CHIP R 47K J 1/16W
R156,157 RK73HB1J472J CHIP R 4.7K J 1/16W
X101 L77-1802-05 CRYSTAL RESONATOR(32768HZ) R158,159 RK73HB1J220J CHIP R 22 J 1/16W
X102 ∗ L77-3015-05 TCXO(18.432MHZ) R160,161 RK73HB1J000J CHIP R 0.0 J 1/16W
R1 RK73HB1J105J CHIP R 1.0M J 1/16W
R2 RK73HB1J104J CHIP R 100K J 1/16W R163 RK73HH1J104D CHIP R 100K D 1/16W
R3 RK73HB1J123J CHIP R 12K J 1/16W R165 RK73HB1J102J CHIP R 1.0K J 1/16W
R4 -10 RK73HB1J103J CHIP R 10K J 1/16W R166 RK73HB1J104J CHIP R 100K J 1/16W
R168 RK73HB1J000J CHIP R 0.0 J 1/16W
R14 RK73HB1J472J CHIP R 4.7K J 1/16W R170 RK73HH1J103D CHIP R 10K D 1/16W
R15 RK73HB1J000J CHIP R 0.0 J 1/16W R171-173 RK73HB1J000J CHIP R 0.0 J 1/16W
19
NX-300
PARTS LIST
New New
R174-178 RK73HB1J104J CHIP R 100K J 1/16W R471 RK73HB1J000J CHIP R 0.0 J 1/16W
R180,181 RK73HB1J104J CHIP R 100K J 1/16W R472 RK73HB1J223J CHIP R 22K J 1/16W
R183 RK73HB1J104J CHIP R 100K J 1/16W R474,475 RK73HB1J333J CHIP R 33K J 1/16W
R184 RK73HB1J473J CHIP R 47K J 1/16W R477,478 RK73HB1J000J CHIP R 0.0 J 1/16W
R185 RK73HB1J105J CHIP R 1.0M J 1/16W R479 RK73HB1J102J CHIP R 1.0K J 1/16W
R186 RK73HB1J473J CHIP R 47K J 1/16W R480 RK73HB1J273J CHIP R 27K J 1/16W
R187 RK73HB1J102J CHIP R 1.0K J 1/16W R481 RK73HB1J474J CHIP R 470K J 1/16W
R192 RK73HB1J102J CHIP R 1.0K J 1/16W R486 RK73HB1J100J CHIP R 10 J 1/16W
R193,194 RK73HB1J104J CHIP R 100K J 1/16W R487-490 RK73HH1J223D CHIP R 22K D 1/16W
R401 RK73HB1J152J CHIP R 1.5K J 1/16W K3 R491 RK73HB1J104J CHIP R 100K J 1/16W
R402 RK73HB1J151J CHIP R 150 J 1/16W R492 RK73HB1J474J CHIP R 470K J 1/16W
R403 RK73HB1J152J CHIP R 1.5K J 1/16W K3 R493 RK73HB1J000J CHIP R 0.0 J 1/16W
R404 RK73HB1J151J CHIP R 150 J 1/16W R494-497 RK73HH1J104D CHIP R 100K D 1/16W
R405 RK73HB1J152J CHIP R 1.5K J 1/16W K3 R498 RK73HB1J333J CHIP R 33K J 1/16W
R406 RK73HB1J000J CHIP R 0.0 J 1/16W R499 RK73HB1J223J CHIP R 22K J 1/16W
R409 RK73HB1J470J CHIP R 47 J 1/16W R501 RK73HB1J222J CHIP R 2.2K J 1/16W
R410-416 RK73HB1J471J CHIP R 470 J 1/16W R502,503 RK73HB1J103J CHIP R 10K J 1/16W
R417 RK73HB1J000J CHIP R 0.0 J 1/16W R504 RK73HB1J102J CHIP R 1.0K J 1/16W
R419,420 RK73HB1J000J CHIP R 0.0 J 1/16W R507-511 RK73HB1J102J CHIP R 1.0K J 1/16W
R424 RK73HH1J683D CHIP R 68K D 1/16W R512 RK73HB1J101J CHIP R 100 J 1/16W
R425 RK73HH1J333D CHIP R 33K D 1/16W R513-515 RK73HB1J102J CHIP R 1.0K J 1/16W
R426-429 RK73HB1J000J CHIP R 0.0 J 1/16W R516 RK73HB1J101J CHIP R 100 J 1/16W
R432,433 RK73HB1J000J CHIP R 0.0 J 1/16W R518 RK73HB1J101J CHIP R 100 J 1/16W
R434 RK73HB1J393J CHIP R 39K J 1/16W R519-528 RK73HB1J102J CHIP R 1.0K J 1/16W
R435,436 RK73HB1J104J CHIP R 100K J 1/16W R529-531 RK73HB1J101J CHIP R 100 J 1/16W
R438,439 RK73HB1J104J CHIP R 100K J 1/16W R533-535 RK73HB1J101J CHIP R 100 J 1/16W
R440 RK73HB1J000J CHIP R 0.0 J 1/16W R536-540 RK73HB1J102J CHIP R 1.0K J 1/16W
R441 RK73HB1J153J CHIP R 15K J 1/16W R541 RK73HB1J101J CHIP R 100 J 1/16W
R442 RK73HB1J102J CHIP R 1.0K J 1/16W R542 RK73HB1J102J CHIP R 1.0K J 1/16W
R446 RK73HB1J274J CHIP R 270K J 1/16W R546,547 RK73HB1J102J CHIP R 1.0K J 1/16W
R448 RK73HB1J103J CHIP R 10K J 1/16W R701-707 RK73HB1J000J CHIP R 0.0 J 1/16W
R449-452 RK73HB1J474J CHIP R 470K J 1/16W R709-715 RK73HB1J000J CHIP R 0.0 J 1/16W
R453 RK73HB1J104J CHIP R 100K J 1/16W R716 RK73GB2A000J CHIP R 0.0 J 1/10W
R454 RK73HB1J474J CHIP R 470K J 1/16W R717-722 RK73HB1J104J CHIP R 100K J 1/16W
R455 RK73HB1J102J CHIP R 1.0K J 1/16W R723 RK73HB1J105J CHIP R 1.0M J 1/16W
R457,458 RK73HB1J104J CHIP R 100K J 1/16W R725 RK73HB1J100J CHIP R 10 J 1/16W
R459,460 RK73HB1J102J CHIP R 1.0K J 1/16W R726 RK73HB1J104J CHIP R 100K J 1/16W
R461 RK73HB1J103J CHIP R 10K J 1/16W R727-729 RK73HB1J105J CHIP R 1.0M J 1/16W
R463 RK73HB1J104J CHIP R 100K J 1/16W R731,732 RK73HB1J105J CHIP R 1.0M J 1/16W
20
NX-300
PARTS LIST
New New
R753 RK73HB1J683J CHIP R 68K J 1/16W R828,829 RK73HB1J000J CHIP R 0.0 J 1/16W
R754 RK73HB1J564J CHIP R 560K J 1/16W R830 RK73HB1J105J CHIP R 1.0M J 1/16W
R758 RK73HB1J103J CHIP R 10K J 1/16W R834 RK73HB1J000J CHIP R 0.0 J 1/16W
R761-764 RK73HB1J223J CHIP R 22K J 1/16W R836 RK73HB1J473J CHIP R 47K J 1/16W
R782 RK73HB1J104J CHIP R 100K J 1/16W R848 RK73HB1J000J CHIP R 0.0 J 1/16W K
R783 RK73HB1J183J CHIP R 18K J 1/16W R849,850 RK73HB1J000J CHIP R 0.0 J 1/16W K3
R784 RK73HB1J104J CHIP R 100K J 1/16W R850 RK73HB1J000J CHIP R 0.0 J 1/16W K
R785 RK73HB1J682J CHIP R 6.8K J 1/16W R851,852 RK73HB1J683J CHIP R 68K J 1/16W
R786 RK73HB1J000J CHIP R 0.0 J 1/16W
R787 RK73HB1J124J CHIP R 120K J 1/16W VR1 2B ∗ R31-0666-05 VARIABLE RESISTOR(VOL)
R788 RK73HB1J473J CHIP R 47K J 1/16W S1 2B ∗ S60-0437-05 ROTARY SWITCH(CH)
R789 RK73HB1J154J CHIP R 150K J 1/16W D11 MA2S111-F DIODE

R790 RK73HB1J102J CHIP R 1.0K J 1/16W D12 -16 ∗ 1SS416 DIODE
R791 RK73HB1J474J CHIP R 470K J 1/16W D17 EMZ6.8N ZENER DIODE
R793 RK73HB1J102J CHIP R 1.0K J 1/16W D18 ,19 ∗ HZC6.8-E ZENER DIODE
R794 RK73HB1J104J CHIP R 100K J 1/16W D20 ,21 NNCD6.8G-A ZENER DIODE
R795 RK73HB1J000J CHIP R 0.0 J 1/16W D22 ,23 DA221 DIODE

R796 RK73HB1J333J CHIP R 33K J 1/16W D101 MA2S111-F DIODE K3
R797 RK73HB1J102J CHIP R 1.0K J 1/16W D102 ∗ 1SS416 DIODE
R798 RK73HB1J104J CHIP R 100K J 1/16W D401-405 1SS388F DIODE
R799 RK73HB1J334J CHIP R 330K J 1/16W D406 HRB0502A DIODE
R800 RK73HB1J474J CHIP R 470K J 1/16W D407 MA2S111-F DIODE

R801 RK73HB1J473J CHIP R 47K J 1/16W D408 1SS301F DIODE
R802 RK73HB1J474J CHIP R 470K J 1/16W D409,410 MA2S111-F DIODE
R803 RK73HB1J103J CHIP R 10K J 1/16W D411 ∗ 1SS416 DIODE
R804 RK73HB1J000J CHIP R 0.0 J 1/16W D412 1SS301F DIODE
R805,806 RK73HB1J473J CHIP R 47K J 1/16W D413 1SS388F DIODE

R807 RK73HB1J102J CHIP R 1.0K J 1/16W D414,415 ∗ 1SS416 DIODE
R808 RK73HB1J471J CHIP R 470 J 1/16W D416,417 1SS388F DIODE
R809 RK73HB1J334J CHIP R 330K J 1/16W D701 1SS301F DIODE
R810 RK73HB1J332J CHIP R 3.3K J 1/16W D702 MA2S111-F DIODE
R812 RK73HB1J562J CHIP R 5.6K J 1/16W D703-706 RB706F-40 DIODE
If a part reference number is listed in a shaded box, that part does not come with the PCB.
21
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
D707 DA221 DIODE Q411 ∗ SSM6N16FE-F FET

IC1 LMC7101BIM5 MOS-IC Q412 SSM3K15TE(F) FET
IC101 Note 1 ROM IC Q413 2SA1955A-F TRANSISTOR
IC102 Note 1 MICROPROCESSOR IC Q414,415 ∗ EMD12 TRANSISTOR
IC103 Note 1 SRAM IC
IC104 TC7SH08FU-F MOS-IC Q701 2SA1832(GR)F TRANSISTOR
Q702,703 SSM3K15TE(F) FET
IC105 ∗ XC6109C29ANN ANALOGUE IC Q704 2SC4617(S) TRANSISTOR
IC106 RV5C386A MOS-IC Q705 2SC4738(GR)F TRANSISTOR
IC107 ∗ SM5023CNDH-G MOS-IC Q706 2SA1832(GR)F TRANSISTOR
IC108 Note 1 MOS-IC
IC109 TC7SH08FU-F MOS-IC Q707 2SJ243-A FET
IC401 ∗ TC74LCX245FK MOS-IC TH1 ERTJ0EV104H THERMISTOR

IC402 ∗ TC7WZ245FK-F MOS-IC TH701 ERTJ0EV104H THERMISTOR
IC403 ∗ LM2682MMX MOS-IC
IC404 XC6204B332M MOS-IC TX-RX UNIT (X57-7370-10)
IC405 ∗ XC6205B152PRN ANALOGUE IC
D900 B30-2278-05 LED(RED/YELLOW)
IC406 XC6204B332M MOS-IC
IC407 ∗ LT1616ES6-PBF ANALOGUE IC C500 CK73HB1A104K CHIP C 0.10UF K
IC408 TC75S51FE(F) MOS-IC C501 CC73HCH1H101J CHIP C 100PF J
IC409 TC7W66FK-F MOS-IC C502 CK73HB1H471K CHIP C 470PF K
IC410 ∗ MCP6021-E/OT MOS-IC C503 CK73HB1A104K CHIP C 0.10UF K
IC411 ∗ NJM2880U105ZB ANALOGUE IC
IC412,413 ∗ TPA6201A1DRBR ANALOGUE IC C505 CC73HCH1H101J CHIP C 100PF J
IC414 XC61CC5602NR MOS-IC C506 CC73HCH1H100C CHIP C 10PF C
IC415 TC7SET08FU-F MOS-IC C508 CK73HB1C103K CHIP C 0.010UF K
IC416 ∗ S-812C31BPI-G ANALOGUE IC C509 CC73HCH1H100C CHIP C 10PF C
C511 CK73FB0J106K CHIP C 10UF K
IC417 ∗ TC7WH126FK MOS-IC
IC418 TC7WT125FUF MOS-IC C512 CK73HB1C103K CHIP C 0.010UF K
IC701 Note 1 MOS-IC C513 CC73HCH1H101J CHIP C 100PF J
IC702 TC75W51FK(F) MOS-IC C514-516 CK73HB1C103K CHIP C 0.010UF K
IC703 M62364FP-F MOS-IC C517-519 CC73HCH1H101J CHIP C 100PF J
IC704 TC75S51FE(F) MOS-IC
IC705 TC75W51FK(F) MOS-IC C521 CC73HCH1H101J CHIP C 100PF J
IC706 TC75S51FE(F) MOS-IC C522 CK73HB1A104K CHIP C 0.10UF K
IC707 TC7W53FK(F) MOS-IC C523,524 CC73HCH1H101J CHIP C 100PF J
IC708 XC6204B502PR MOS-IC C525 CC73HCH1H470J CHIP C 47PF J
IC709 TC7W53FK(F) MOS-IC
IC710,711 TC75W51FK(F) MOS-IC C527-529 CC73HCH1H101J CHIP C 100PF J
IC712 TC7S66FUF MOS-IC C533 CK73HB1H471K CHIP C 470PF K
IC713 TC75W51FK(F) MOS-IC C534 CC73HCH1H101J CHIP C 100PF J
IC714 TC7W53FK(F) MOS-IC C535 CS77AA1VR15M CHIP TNTL 0.15UF 35WV
IC716 TC75W51FK(F) MOS-IC C537 CC73HCH1H050B CHIP C 5.0PF B
C539 ∗ CS77BA1D100M CHIP TNTL 10UF 20WV
Q1 2SA1362-F(GR) TRANSISTOR C541 C92-0863-05 CHIP TNTL 0.047UF 35WV
Q2 2SC4617(S) TRANSISTOR C542 C93-0787-05 CERAMIC 0.1UF 50WV
Q3 ,4 SSM3K15TE(F) FET C543 CC73HCH1H030B CHIP C 3.0PF B
Q5 2SJ347F FET
Q101 2SA1832(GR)F TRANSISTOR K3 C546 CK73HB1H472K CHIP C 4700PF K
C547,548 CC73HCH1H101J CHIP C 100PF J
Q102 2SC4617(S) TRANSISTOR K3 C550 CC73HCH1H050B CHIP C 5.0PF B
Q103 SSM3K15TE(F) FET K3 C553 CC73HCH1H100B CHIP C 10PF B
Q401,402 ∗ SSM6N16FE-F FET C554 CC73HCH1H470J CHIP C 47PF J
Q403 2SA1955A-F TRANSISTOR
Q404 SSM3K15TE(F) FET C555 CK73HB0J105K CHIP C 1.0UF K
Q405 ∗ SSM6N16FE-F FET C562 CK73HB0J105K CHIP C 1.0UF K
Q406 2SB1132(Q,R) TRANSISTOR C565 CC73HCH1H270J CHIP C 27PF J
Q407 UMG3N TRANSISTOR C566 CC73HCH1H560J CHIP C 56PF J
Q408 ∗ EMD12 TRANSISTOR
Q409 2SA1955A-F TRANSISTOR C567,568 CC73HCH1H0R5B CHIP C 0.5PF B
C570 CC73HCH1HR75B CHIP C 0.75PF B
Q410 SSM3K15TE(F) FET C571 CC73HCH1H040B CHIP C 4.0PF B
Note 1 : This part cannot be replaced. Therefore, this part is not supplied as a service part.
22
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
C572 CK73FB0J106K CHIP C 10UF K C668 CC73GCH1H080B CHIP C 8.0PF B

C573 CC73HCH1H050B CHIP C 5.0PF B C669 CC73GCH1H040B CHIP C 4.0PF B
C574 CC73HCH1H020B CHIP C 2.0PF B
C575,576 CC73HCH1H050B CHIP C 5.0PF B C671 CC73HCH1H070B CHIP C 7.0PF B
C577 CK73HB1H471K CHIP C 470PF K C672 CK73HB1H471K CHIP C 470PF K
C578 CK73GB0J475K CHIP C 4.7UF K C689-691 CK73HB1A104K CHIP C 0.10UF K
C579 CC73HCH1H040B CHIP C 4.0PF B C700 CC73HCH1H070B CHIP C 7.0PF B
C581 CC73HCH1H0R5B CHIP C 0.5PF B C703 CK73HB1A104K CHIP C 0.10UF K
C582 CK73HB1H471K CHIP C 470PF K C704 CC73HCH1H470J CHIP C 47PF J
C583 CC73HCH1H0R5B CHIP C 0.5PF B C706 CC73HCH1H100B CHIP C 10PF B
C584,585 CK73HB1H471K CHIP C 470PF K C707 CC73HCH1H680J CHIP C 68PF J
C587 CK73HB1H471K CHIP C 470PF K C709-711 CK73HB1A104K CHIP C 0.10UF K
C588 CC73HCH1H100B CHIP C 10PF B C712 CC73HCH1H680J CHIP C 68PF J
C600 CK73HB1A104K CHIP C 0.10UF K C713 ∗ CK73FB1A106K CHIP C 10UF K
C601 CC73HCH1H101J CHIP C 100PF J C715 CK73HB1C103K CHIP C 0.010UF K
C603 CC73HCH1H100B CHIP C 10PF B C718 CK73HB1A104K CHIP C 0.10UF K
C604,605 CK73HB1H471K CHIP C 470PF K C719 ∗ CK73FB1A106K CHIP C 10UF K
C607 CC73HCH1H070B CHIP C 7.0PF B C720 CC73HCH1H100B CHIP C 10PF B
C610-612 CK73HB1H471K CHIP C 470PF K C721 CK73HB1A104K CHIP C 0.10UF K
C722 CC73HCH1H470G CHIP C 47PF G
C614,615 CK73HB1H471K CHIP C 470PF K C723,724 CK73HB1A104K CHIP C 0.10UF K
C617,618 CK73HB1H471K CHIP C 470PF K C725 CK73HB1C103K CHIP C 0.010UF K
C619 CK73HB1A104K CHIP C 0.10UF K C727,728 CK73HB1A104K CHIP C 0.10UF K
C621 CC73HCH1H150J CHIP C 15PF J C729 CK73FB1E474K CHIP C 0.47UF K
C623 CC73HCH1H150J CHIP C 15PF J C732 CK73HB1H471K CHIP C 470PF K
C625 CK73HB1H471K CHIP C 470PF K C733,734 CK73HB1C103K CHIP C 0.010UF K
C626 CK73HB1A104K CHIP C 0.10UF K C735 CC73HCH1H470G CHIP C 47PF G
C627 CC73HCH1H100B CHIP C 10PF B C736 CK73HB1C103K CHIP C 0.010UF K
C628 CC73HCH1H100C CHIP C 10PF C
C629 CK73HB1H471K CHIP C 470PF K C738 CC73HCH1H220G CHIP C 22PF G
C630 CK73GB1E105K CHIP C 1.0UF K C739 CC73HCH1H060B CHIP C 6.0PF B
C631 CS77AA1A6R8M CHIP TNTL 6.8UF 10WV C740,741 CK73HB1C103K CHIP C 0.010UF K
C632 CK73HB1H471K CHIP C 470PF K C742 CK73FB1A475K CHIP C 4.7UF K
C639 CC73HCH1H390J CHIP C 39PF J C744,745 CK73HB1H471K CHIP C 470PF K
C640 CC73HCH1H470J CHIP C 47PF J C746 CC73HCH1H090B CHIP C 9.0PF B
C641 CC73HCH1H100C CHIP C 10PF C C747 CC73HCH1H100B CHIP C 10PF B
C642,643 CC73HCH1H151J CHIP C 150PF J C748 CK73HB1H471K CHIP C 470PF K
C645 CK73GB1C104K CHIP C 0.10UF K
C646 CK73GB1E105K CHIP C 1.0UF K C750 CK73HB1C103K CHIP C 0.010UF K
C647 C93-0941-05 CERAMIC 18PF 50WV C751 CC73HCH1H100B CHIP C 10PF B
C648,649 CK73HB1C103K CHIP C 0.010UF K C752 CK73HB1H471K CHIP C 470PF K
C650 C93-0937-05 CERAMIC 12PF 50WV C753 CC73HCH1H020B CHIP C 2.0PF B
C652 C93-0951-05 CERAMIC 47PF 50WV C755 CC73HCH1H040B CHIP C 4.0PF B
C653 CK73HB1H471K CHIP C 470PF K C756 CC73HCH1H090B CHIP C 9.0PF B
C654 ∗ C93-0987-05 CERAMIC 7.5PF 50WV C758 CK73HB1H471K CHIP C 470PF K
C660 CC73GCH1H101J CHIP C 100PF J C759,760 CK73HB1A104K CHIP C 0.10UF K
C662 CC73GCH1H010B CHIP C 1.0PF B C764 CC73HCH1H1R5B CHIP C 1.5PF B
C663 CC73GCH1H101J CHIP C 100PF J C765 CK73HB1H471K CHIP C 470PF K
C664 CC73GCH1H040B CHIP C 4.0PF B C766 CK73GB1H104K CHIP C 0.10UF K
C665 CC73GCH1H020B CHIP C 2.0PF B C767 CC73HCH1H090B CHIP C 9.0PF B
C666 CC73GCH1H050B CHIP C 5.0PF B
C667 CC73GCH1H1R5B CHIP C 1.5PF B C769 CK73HB1H471K CHIP C 470PF K
23
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
C770 CC73HCH1H040B CHIP C 4.0PF B C970,971 CK73HB1H102K CHIP C 1000PF K

C771 CK73HB1H471K CHIP C 470PF K C972-974 CK73GB1E105K CHIP C 1.0UF K
C772 CC73HCH1H090B CHIP C 9.0PF B C975 ∗ C93-0987-05 CERAMIC 7.5PF 50WV
C773 CC73HCH1H010B CHIP C 1.0PF B C976 CC73HCH1H470J CHIP C 47PF J
C977 ∗ CK73HB1A474K CHIP C 0.47UF K
C775 CK73HB1H471K CHIP C 470PF K CN600 ∗ E23-1326-05 TERMINAL
C776 CC73HCH1H090B CHIP C 9.0PF B CN737 E40-6358-05 SOCKET FOR PIN ASSY
C777,778 CK73HB1H471K CHIP C 470PF K CN900 ∗ E40-6422-15 SOCKET FOR PIN ASSY
C779 CK73HB1C103K CHIP C 0.010UF K CN901 ∗ E40-6752-05 FLAT CABLE CONNECTOR
CN902 ∗ E23-1326-05 TERMINAL
C780 CK73GB1H104K CHIP C 0.10UF K
C782 CC73HCH1H0R5B CHIP C 0.5PF B F900 F53-0324-05 FUSE
C784-786 CK73HB1H471K CHIP C 470PF K CF700 L72-1017-05 CERAMIC FILTER
C788 CK73GB1H104K CHIP C 0.10UF K CF701 ∗ L72-1020-05 CERAMIC FILTER
C789 CK73HB1H471K CHIP C 470PF K L500 L41-4795-39 SMALL FIXED INDUCTOR(4.7U/2520

C790 CK73HB1A104K CHIP C 0.10UF K L503 L92-0163-05 BEADS CORE
C791 CK73HB1H471K CHIP C 470PF K L504 L40-1275-92 SMALL FIXED INDUCTOR(12NH/1608
C792 CK73HB1A104K CHIP C 0.10UF K L508,509 L40-2285-92 SMALL FIXED INDUCTOR(220NH/160
C794,795 CK73HB1H471K CHIP C 470PF K L513 L40-1878-92 SMALL FIXED INDUCTOR(18NH/1608
C796 CC73HCH1H090B CHIP C 9.0PF B L514-519 L40-2285-92 SMALL FIXED INDUCTOR(220NH/160

C798 CC73HCH1H1R5B CHIP C 1.5PF B L520 L40-1878-67 SMALL FIXED INDUCTOR(18NH/8)
C799 CK73HB1H471K CHIP C 470PF K L521 L40-2278-67 SMALL FIXED INDUCTOR(22NH/8)
C800 CC73HCH1H020B CHIP C 2.0PF B L522 L40-2285-92 SMALL FIXED INDUCTOR(220NH/160
C801 CK73HB1H471K CHIP C 470PF K L523 L92-0446-05 BEADS CORE
C802,803 CC73HCH1H040B CHIP C 4.0PF B L524-526 L40-2285-92 SMALL FIXED INDUCTOR(220NH/160

C804 CC73HCH1H090B CHIP C 9.0PF B L527 L92-0446-05 BEADS CORE
C809 CC73GCH1H180J CHIP C 18PF J L598,599 L92-0163-05 BEADS CORE

C850 CC73HCH1H101J CHIP C 100PF J L604 L92-0138-05 CHIP FERRITE
C900 CK73GB1H102K CHIP C 1000PF K L605 L40-6865-92 SMALL FIXED INDUCTOR(6.8NH/160
C901,902 CK73HB1H471K CHIP C 470PF K L606 L41-1875-43 SMALL FIXED INDUCTOR(18NH/2015
C903 CK73GB1H471K CHIP C 470PF K L607 L92-0149-05 CHIP FERRITE

C904-908 CC73HCH1H470J CHIP C 47PF J L609 L34-4575-05 AIR-CORE COIL
C910 CC73HCH1H470J CHIP C 47PF J L610 L92-0149-05 CHIP FERRITE
C912-920 CC73HCH1H470J CHIP C 47PF J L611 L41-2285-43 SMALL FIXED INDUCTOR(220NH/201
C922,923 CC73HCH1H470J CHIP C 47PF J L612-614 L34-4564-05 AIR-CORE COIL
C925-943 CC73HCH1H470J CHIP C 47PF J L615 L40-1575-57 SMALL FIXED INDUCTOR(15.0N/5%/

C944 CK73HB1H471K CHIP C 470PF K L701 L40-5681-86 SMALL FIXED INDUCTOR(0.56UH/16
C945,946 CC73HCH1H470J CHIP C 47PF J L703 ∗ L41-4778-45 SMALL FIXED INDUCTOR(47NH/1608
C947 CK73HB1H471K CHIP C 470PF K L704 L40-1891-86 SMALL FIXED INDUCTOR(1.8U/1608
C948,949 CK73GB1E105K CHIP C 1.0UF K L705,706 L92-0138-05 CHIP FERRITE
C950 C92-0765-05 CHIP-TAN 4.7UF 16WV L707 L41-2785-39 SMALL FIXED INDUCTOR(0.27U/252
C951 ∗ CK73GB1C224K CHIP C 0.22UF K L708 L41-5685-39 SMALL FIXED INDUCTOR(0.56U/252
C952 CK73HB1H102K CHIP C 1000PF K L709,710 L40-1875-92 SMALL FIXED INDUCTOR(18NH/1608
C953 CK73HB1A104K CHIP C 0.10UF K L711 L40-2275-92 SMALL FIXED INDUCTOR(22NH/1608
C954 ∗ CK73GB1C224K CHIP C 0.22UF K L713-715 L41-8268-14 SMALL FIXED INDUCTOR(8.2NH/201
C955,956 CK73HB1H102K CHIP C 1000PF K L716 L92-0138-05 CHIP FERRITE

C957,958 CK73GB1E105K CHIP C 1.0UF K L717 L41-2285-14 SMALL FIXED INDUCTOR(220NH/201
C962 CC73HCH1E181J CHIP C 180PF J L721,722 L41-8268-14 SMALL FIXED INDUCTOR(8.2NH/201
C963 CK73GB1E105K CHIP C 1.0UF K L723 L34-4564-05 AIR-CORE COIL
C964,965 ∗ CK73GB1C224K CHIP C 0.22UF K L725 L40-8265-92 SMALL FIXED INDUCTOR(8.2NH/160

C966 CC73HCH1H220J CHIP C 22PF J L726 L41-3378-03 SMALL FIXED INDUCTOR(33N/2P/16
C967 CK73HB1H471K CHIP C 470PF K L780 L40-1085-57 SMALL FIXED INDUCTOR(100N/5%/1
C968 ∗ CK73GB1C224K CHIP C 0.22UF K L900 L92-0149-05 CHIP FERRITE
C969 CK73GB1E105K CHIP C 1.0UF K L901 L33-1462-05 SMALL FIXED INDUCTOR
24
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
X500 ∗ L77-3016-05 TCXO (19.2M/4P/12) R606 RK73HB1J331J CHIP R 330 J 1/16W

XF700 ∗ L71-0640-05 MCF (58.05MHZ/16) R607 RK73HB1J222J CHIP R 2.2K J 1/16W
R608 RK73HB1J470J CHIP R 47 J 1/16W
R430 RK73GB2A000J CHIP R 0.0 J 1/10W
R431,432 RK73HB1J000J CHIP R 0.0 J 1/16W R609 RK73HB1J000J CHIP R 0.0 J 1/16W
R500,501 RN73HH1J104D CHIP R 100K D 1/16W R610 RK73HB1J472J CHIP R 4.7K J 1/16W
R503 RK73HB1J100J CHIP R 10 J 1/16W R616 RK73HB1J181J CHIP R 180 J 1/16W
R617 RK73HB1J331J CHIP R 330 J 1/16W
R505 RK73HB1J000J CHIP R 0.0 J 1/16W R618 RK73HB1J220J CHIP R 22 J 1/16W
R511-514 RK73HB1J100J CHIP R 10 J 1/16W R622 RK73HB1J101J CHIP R 100 J 1/16W
R521,522 RK73HB1J100J CHIP R 10 J 1/16W R627,628 RK73HB1J000J CHIP R 0.0 J 1/16W
R532 RK73HB1J000J CHIP R 0.0 J 1/16W R634 RK73HB1J000J CHIP R 0.0 J 1/16W
R636 RK73HB1J221J CHIP R 220 J 1/16W
R534 RK73HH1J473D CHIP R 47K D 1/16W
R537 RK73HB1J102J CHIP R 1.0K J 1/16W R642 RK73EB2ER39K CHIP R 0.39 K 1/4W
R538 ∗ RK73HH1J391D CHIP R 390 D 1/16W R644 RK73HB1J470J CHIP R 47 J 1/16W
R645 RK73EB2ER39K CHIP R 0.39 K 1/4W
R539 RK73HB1J106J CHIP R 10M J 1/16W
R542-545 RK73HB1J000J CHIP R 0.0 J 1/16W R647 RK73EB2ER39K CHIP R 0.39 K 1/4W
R546 RK73HB1J104J CHIP R 100K J 1/16W R648,649 RK73HH1J154D CHIP R 150K D 1/16W
R547 RK73HB1J000J CHIP R 0.0 J 1/16W R650 RK73GB2A000J CHIP R 0.0 J 1/10W
R651-654 RK73HH1J274D CHIP R 270K D 1/16W
R554,555 RK73HB1J473J CHIP R 47K J 1/16W R658 RK73HB1J182J CHIP R 1.8K J 1/16W
R559 ∗ RK73HH1J181D CHIP R 180 D 1/16W R661 RK73HB1J104J CHIP R 100K J 1/16W
R560 RK73HB1J220J CHIP R 22 J 1/16W R663 RK73FB2B000J CHIP R 0.0 J 1/8W
R561 ∗ RK73HH1J181D CHIP R 180 D 1/16W R664 RK73HB1J000J CHIP R 0.0 J 1/16W
R665,666 RK73HB1J271J CHIP R 270 J 1/16W
R563 RK73HB1J473J CHIP R 47K J 1/16W R667 RK73EB2E823J CHIP R 82K J 1/4W
R570,571 RK73HB1J000J CHIP R 0.0 J 1/16W R704 RK73HB1J102J CHIP R 1.0K J 1/16W
R572 RK73HB1J100J CHIP R 10 J 1/16W R705 RK73HB1J000J CHIP R 0.0 J 1/16W
R574-576 RK73HB1J000J CHIP R 0.0 J 1/16W R709 RK73HB1J103J CHIP R 10K J 1/16W
R710 RK73HB1J000J CHIP R 0.0 J 1/16W
25
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
R724 RK73HB1J104J CHIP R 100K J 1/16W R901 RK73GB2A000J CHIP R 0.0 J 1/10W
R903 RK73HB1J821J CHIP R 820 J 1/16W
R727 RK73HB1J222J CHIP R 2.2K J 1/16W R904 RK73HB1J000J CHIP R 0.0 J 1/16W
R728 RK73HB1J221J CHIP R 220 J 1/16W R905 RK73HB1J330J CHIP R 33 J 1/16W
R731 RK73HB1J103J CHIP R 10K J 1/16W R907 RK73GB2A100J CHIP R 10 J 1/10W
R735 RK73HB1J101J CHIP R 100 J 1/16W R909 RK73GB2A000J CHIP R 0.0 J 1/10W
R736 RK73HB1J104J CHIP R 100K J 1/16W R910-912 RK73HB1J474J CHIP R 470K J 1/16W
R915-917 RK73HB1J474J CHIP R 470K J 1/16W
R739 RK73HB1J221J CHIP R 220 J 1/16W
R740 RK73HB1J470J CHIP R 47 J 1/16W R918,919 RK73HB1J102J CHIP R 1.0K J 1/16W
R742 RK73HB1J472J CHIP R 4.7K J 1/16W R920,921 RK73HB1J473J CHIP R 47K J 1/16W
R925 RK73HH1J334D CHIP R 330K D 1/16W
R746 RK73HB1J104J CHIP R 100K J 1/16W R926 RK73HH1J223D CHIP R 22K D 1/16W
R750 RK73GB2A000J CHIP R 0.0 J 1/10W S1 S70-0483-05 TACT SWITCH

R752,753 RK73HB1J000J CHIP R 0.0 J 1/16W
R755 RK73HB1J472J CHIP R 4.7K J 1/16W D501 HSC119 DIODE
R757 RK73HB1J104J CHIP R 100K J 1/16W D505 DA221 DIODE
R758 RK73HB1J103J CHIP R 10K J 1/16W D506,507 1SV325F VARIABLE CAPACITANCE DIODE
D510,511 1SV282-F VARIABLE CAPACITANCE DIODE
R759,760 RK73HB1J104J CHIP R 100K J 1/16W D514-517 1SV282-F VARIABLE CAPACITANCE DIODE
R761 RK73HB1J101J CHIP R 100 J 1/16W
R762 RK73HB1J103J CHIP R 10K J 1/16W D518 HSC119 DIODE
R763 RK73HB1J824J CHIP R 820K J 1/16W D519 1SV278F VARIABLE CAPACITANCE DIODE
R764 RK73HB1J104J CHIP R 100K J 1/16W D600,601 HSC277 DIODE
D604 HZU2ALL ZENER DIODE
R765 RK73HB1J000J CHIP R 0.0 J 1/16W D605 HZU5CLL ZENER DIODE
R768 RK73HB1J000J CHIP R 0.0 J 1/16W
R769 RK73HB1J103J CHIP R 10K J 1/16W D606,607 HVC131 DIODE
R770 RK73HB1J680J CHIP R 68 J 1/16W D608 HSC119 DIODE
R771 RK73HB1J181J CHIP R 180 J 1/16W D700 HSC119 DIODE
D702-704 1SV286F VARIABLE CAPACITANCE DIODE
R772 RK73HB1J000J CHIP R 0.0 J 1/16W D705 HSC119 DIODE
R774,775 RK73HB1J104J CHIP R 100K J 1/16W D706 1SV286F VARIABLE CAPACITANCE DIODE
R777 RK73HB1J103J CHIP R 10K J 1/16W D708 1SV286F VARIABLE CAPACITANCE DIODE
R778 RK73HB1J104J CHIP R 100K J 1/16W D709 HVC131 DIODE
D710 1SV286F VARIABLE CAPACITANCE DIODE
R779 RK73HB1J683J CHIP R 68K J 1/16W D711 HVC131 DIODE
R780 RK73HB1J000J CHIP R 0.0 J 1/16W
R781 RK73HB1J182J CHIP R 1.8K J 1/16W D901 1SR154-400 DIODE
R783 RK73HB1J224J CHIP R 220K J 1/16W D902 HSC119 DIODE
IC404 TC75W51FUF MOS-IC
R785 RK73HB1J104J CHIP R 100K J 1/16W IC500 ∗ LM73CIMKX-0 MOS-IC
R786 RK73HB1J000J CHIP R 0.0 J 1/16W IC501 LMC7101BIM5 MOS-IC
R788 RK73HB1J104J CHIP R 100K J 1/16W IC502 Note 1 MOS-IC
R790 RK73HB1J104J CHIP R 100K J 1/16W IC503 LMC7101BIM5 MOS-IC
R791 RK73HB1J000J CHIP R 0.0 J 1/16W
IC504 TC75W51FUF MOS-IC
R792 RK73HB1J104J CHIP R 100K J 1/16W IC600 TA75W01FUF MOS-IC
R794,795 RK73HB1J103J CHIP R 10K J 1/16W IC700 ∗ MCP6021-E/OT MOS-IC
R796 RK73HB1J000J CHIP R 0.0 J 1/16W IC701 TK10931VTL-G ANALOGUE IC
R797 RK73HB1J473J CHIP R 47K J 1/16W IC702,703 LMC7101BIM5 MOS-IC
Note 1 : This part cannot be replaced. Therefore, this part is not supplied as a service part.
26
NX-300
PARTS LIST
TX-RX UNIT (X57-7370-10)
New New
IC901 XC9101D09AKR ANALOGUE IC

IC902 TK11250CUCB MOS-IC
IC903 ∗ TK71733S BI-POLAR IC
Q503 2SC5383-T111 TRANSISTOR

Q504 ∗ 2SK879-F(Y) FET
Q505 2SC5636 TRANSISTOR
Q508,509 2SK508NV(K52) FET
Q510 SSM6L05FU-F FET

Q511 2SJ347F FET
Q512 2SC5636 TRANSISTOR
Q600,601 2SC5636 TRANSISTOR
Q602 2SK3077F FET
Q603 RD01MUS1-T113 FET

Q605 SSM3K15TE(F) FET
Q606 RD07MVS1BT122 FET
Q607 DTC144EE DIGITAL TRANSISTOR
Q608 2SK1824-A FET

Q610 ∗ EMD5 TRANSISTOR
Q700 2SC5108(Y)F TRANSISTOR
Q701 2SC4215-F(Y) TRANSISTOR
Q703 3SK318 FET

Q705 3SK318 FET
Q706 2SK1830F FET
Q900 UMG9N TRANSISTOR
Q901-903 SSM6L05FU-F FET
Q904 ∗ SSM5H01TU-F FET

Q905 2SA1955A-F TRANSISTOR
TH600 ERTJ0EV104H THERMISTOR
27
NX-300
EXPLODED VIEW
A B
10 61
2 60
8 9
54
54
A
54
40 1
1
4
6
64
20 59
5 58
705
54
706 54
Control unit 38 37
(X53) Hx2
Hx2
50
67 69
Option board 70
unit (X57 B/2)
29
33
H 53
65
709 H
44 Hx2
707
23
48 H
2 66 Hx2
H 707 31
708 43
D
H 39
45
30 S1 39
D
Hx8
E 47
72 F
TX-RX unit 42 E 21 12
15 54 19 VR1
(X57 A/2)
F
41
25
26 21
52
7 3
704
14 34
57
68
A :N08-0564-04
700 B :N09-2426-14
C :N09-2440-15
49
D :N09-6549-04
55 E :N09-6554-05
C
24 F :N14-0844-04
C 27
3 G :N30-3008-60
16
35 H :N83-2005-48
703
36 56
17
701 18 B
E
E
702
Parts with the exploded numbers larger than 700 are not supplied.
28
If a part reference number is listed in a box on the exploded view of the PCB, that part does not come with the PCB. These parts must be ordered separately.
NX-300
PACKING
C D
46. BELT CLIP 4. CAP

(J29-0730-05) (B09-0712-03)
40. PACKING(CAP)
(G11-1769-04)
G. PAN HEAD MACHINE SCREW
(N30-3008-60)x2
1 A. DRESSED SCREW
(N08-0564-04)
711
11. INSTRUCTION MANUAL

(B62-2014-00) 712
711
713
Parts with the exploded numbers larger than 700 are not supplied. 29
NX-300
ADJUSTMENT
Fault diagnosis of the BGA IC
Overview: A flowchart for determining whether or not the transceiver can be powered on (the LCD does not function even if the
power switch is turned on) due to broken BGA parts.
BGA parts
• ASIC (IC108)
• DSP (IC102)
• FLASH (IC101)
• SRAM (IC103)
● Checking power supply voltage
Checking voltage When an abnormal Checking an abnormal point

value is confirmed.
Points to be checked Normal voltage 33M has an abnormal voltage.
33M IC404 (5 pin) 3.3V [ASIC]
15M IC405 (5 pin) 1.5V Remove L714 to check the voltage of the 33M.
33A IC406 (5 pin) 3.3V If the voltage becomes normal, the ASIC is broken.
31BU IC416 (3 pin) 3.1V [DSP]
Remove L712 to check the voltage of the 33M.
Power supply of each device is connected through the coil. If the voltage becomes normal, the DSP is broken.
[ASIC] [FLASH]
33M:L714 15M:L715 33A:L716 Remove L717 to check the voltage of the 33M.
[DSP] If the voltage becomes normal, the FLASH is broken.
33M:L712 15M:L711
[FLASH] 15M has an abnormal voltage.
33M:L717 [ASIC]
[SRAM] Remove L715 to check the voltage of the 15M.
31BU:L710 If the voltage becomes normal, the ASIC is broken.
[DSP]
When a normal value Remove L711 to check the voltage of the 15M.
● Checking the clock is confirmed. If the voltage becomes normal, the DSP is broken.
Checking the clock 33A has an abnormal voltage.

When an abnormal [ASIC]
Points to be checked Normal voltage (3.3V) value is confirmed. Remove L716 to check the voltage of the 33A.
18.432MHz ASIC side R158 18.432MHz If the voltage becomes normal, the ASIC is broken.
DSP side R159 18.432MHz
32.768kHz IC106(1 pin) 32.768kHz 31BU has an abnormal voltage.
[SRAM]
● Checking the When a normal value Remove L710 to check the voltage of the 31BU.
Reset/Control signal is confirmed. If the voltage becomes normal, the SRAM is broken.
Checking the control signal input to the ASIC If the voltage is not corrected, there is a problem
other than the BGA parts.
Points to be checked Normal voltage
RESET IC105 (4 pin) 3.3V When an abnormal
/BINT Q401 (6 pin) 3.3V value is confirmed.
/PSW Q402 (3 pin) 3.3V The BGA parts are not broken.
When a normal value

is confirmed.
Checking the control signal output from the ASIC When an abnormal If the /FRST is always 0V, the ASIC is broken.
value is confirmed.
Points to be checked Normal voltage If the /FRST repeats 3.3V and 0V at intervals,
/FRST C110 3.3V the ASIC, FLASH and SRAM may be broken.
When a normal value

is confirmed.
30
NX-300
ADJUSTMENT
When a normal value

is confirmed.
● Checking the output signal
from the ASIC When an abnormal
Points to be checked Normal voltage value is confirmed. Remove R432. If the ASIC side is 0V,
SBC R432 3.3V the ASIC/FALSH/SRAM may be broken.
When a normal value

is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed.
If the /DRST is 0V, the ASIC/FALSH/SRAM are broken.
/DRST C109 3.3V
When a normal value

● The LCD displays control is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed. Remove R406. If the ASIC side is 0V,
/LCDRST R406 3.3V the ASIC/FALSH/SRAM may be broken.
When a normal value

Points to be checked Normal voltage value is confirmed. If the /CS4 is 0V or 3.3V, the ASIC/FALSH/SRAM
/CS4 IC402 (7 pin) 3.3V→0V→3.3V may be broken.
When a normal value

Points to be checked Normal voltage value is confirmed.
If 5A is 0V, parts other than the BGA are broken.
5A IC708 (5 pin) 5.0V
When a normal value

is confirmed.
It is unlikely that the BGA parts are broken.
● When an error display appears on the LCD.
An error occurs when the ASIC internal RAM reads

The LCD displays "INIT ERROR1".
or writes. The ASIC may be broken.
An error occurs when the DSP internal RAM reads

or writes. The DSP may be broken.
An error occurs when the SRAM internal RAM

reads or writes. The SRAM may be broken.
* Descriptions of signal names

1) RST(RESET) : ASIC reset signal LOW → Reset
2) /BINT : Battery final voltage monitoring LOW → Final voltage
3) /PSW : Power switch signal LOW → ON
4) /FRST : FLASH reset signal LOW → Reset
5) SBC : Switch B control HIGH → ON
6) /DRST : DSP reset signal LOW → Reset
7) /LCDRST : LCD reset signal LOW → Reset
8) /CS4 : LCD controller chip select signal LOW → Active
9) 5A : Analog peripheral control 5.0V power supply
31
NX-300
ADJUSTMENT
Controls [PTT] Transmit -

Use as the DTMF keypad.
Selector
[0] to [9] If a key is pressed during
Power switch / Volume and transmission, the DTMF -
Orange key [#], [ ] corresponding to the key
* that was presses is sent.
“FNC” appears on the sub LCD display

Key
Function Display
[Selector] - -
[ ] Function off -
Analog: “A”
[ ] Analog/NXDN
PTT switch NXDN: “N”
Universal
connector [Side1] Function off -
Side1 key [Side2] LCD all lights LCD all point appears
MIC
Side2 key
High: “H”
[ ] High power/Low power
Low: “L”
1 DEF
4 GHI
2
5
ABC
JKL
3
6 MN
O [ ] Function off -
7 PQ YZ
RS 9 WX
8 TUV
0
#
[ ] Compander on/off On: icon appears
[ ] Beat shift on/off On: icon appears
[Orange] Function off -
Panel Test Mode
[PTT] Transmit -
■ Test mode operation features
[0] to [9]
This transceiver has a test mode. To enter test mode,
and Function off -
press and hold the [ ] key while turning the transceiver
[#], [ ]
power ON. Before the transceiver enters test mode, the *
frequency version information appears on the LCD mo-
• LED indicator
mentarily. Test mode can be inhibited by programming. To
Red LED Lights during transmission.
exit test mode, turn the transceiver power OFF. The follow-
Green LED Lights when there is carrier.
ing functions are available in test mode.
• Sub LCD indicator

■ Key operation “FNC” Appears at function on.
“FNC” not appears on the sub LCD display
Key
Function Display • LCD display in panel test mode
[Selector] - -
Temperature
Push: Test channel up
[ ] Hold: Test channel up Channel No.
continuously +25
Push: Test channel down An SQ5 1- 1

[ ] Hold: Test channel down Channel No.
continuously Sub LCD Signaling No.
Push: Squelch level up Squelch level display Channel No.
[Side1] Squelch level
Hold: Squelch off Squelch off: icon appears
(Analog mode only)
Wide : “w” An : Analog narrow mode
[Side2] Wide/Narrow/Very narrow Narrow : “n” Aw : Analog wide mode
Very narrow : “v” Nn : NXDN narrow mode
[ ] Shift to panel tuning mode - Nv : NXDN very narrow mode
“FNC” appears on the

[ ] Function on
sub LCD display
[ ] MSK 1200bps and 2400bps 2400bps : icon appears
Push: Test signaling up
[ ] Hold: Test signaling up Signaling No.
continuously
[Orange] - -
32
NX-300
ADJUSTMENT
■ Frequency and Signaling • NXDN mode signaling
The transceiver has been adjusted for the frequencies
No. RX TX
shown in the following table. When required, readjust them
following the adjustment procedure to obtain the frequencies 1 RAN1 RAN1
you want in actual operation. 2 None PN9
3 RAN1 Maximum deviation pattern
• Test frequency
CH RX (MHz) TX (MHz) Panel Tuning Mode
1 485.05000 485.10000 ■ Preparations for tuning the transceiver
2 450.05000 450.10000 Before attempting to tune the transceiver, connect the
3 519.95000 519.90000 unit to a suitable power supply.
Whenever the transmitter is turned, the unit must be con-
4 485.00000 485.00000
nected to a suitable dummy load (i.e. power meter).
5 485.20000 485.20000 The speaker output connector must be terminated with a
6 485.40000 485.40000 8Ω dummy load and connected to an AC voltmeter and an
7~16 - - audio distortion meter or a SINAD measurement meter at all
times during tuning.
• Analog mode signaling ■ Transceiver tuning (To enter tuning mode)

No. RX TX To enter tuning mode, press the [ ] key while the trans-
1 None None ceiver is in test mode. Use the [ ] key to write tuning data
through tuning modes, and the [ ]/[ ] key to adjust tun-
2 None 100Hz Square Wave
ing requirements (1 to 4096 appears on the LCD).
3 LTR Data : LTR Data : Use the [ ] key to select the adjustment item through
AREA=0, GOTO=12 AREA=0, GOTO=12 tuning modes. Use the [ ] key to adjust 5 reference level
HOME=12 HOME=12 adjustments, and use the [Side2] key to switch between
ID=47, FREE=25 ID=47, FREE=25 Wide/Narrow/Very narrow.
4 QT : 67.0Hz QT : 67.0Hz
5 QT : 151.4Hz QT : 151.4Hz • LCD display in panel tuning mode
6 QT : 210.7Hz QT : 210.7Hz
CV voltage, AD value, etc
7 QT : 254.1Hz QT : 254.1Hz
8 DQT : D023N DQT : D023N 2.6
9 DQT : D754I DQT : D754I An CNTR 256
10 DTMF : 159D DTMF : 159D
11 None DTMF Code 9 Adjustment point Adjustment value
L (1~4096)
12 2-tone : 2-tone :
L' Proper value guide
A : 304.7Hz A : 304.7Hz C (Frequency adjust only)
B : 3106.0Hz B : 3106.0Hz H'
H Adjustment item
13 Single Tone : 979.9Hz Single Tone : 979.9Hz
14 None Single Tone : 1000Hz
15 None MSK
16 MSK MSK
33
NX-300
ADJUSTMENT
■ Key operation ■ 5 reference level adjustments frequency
Function Tuning point RX (MHz) TX (MHz)
Key
Push Hold (1 second) Low 450.05000 450.10000
[Selector] - Low’ 467.55000 467.60000
[ ] Adjustment value up Continuation up Center 485.05000 485.10000
[ ] Adjustment value down Continuation down High’ 502.55000 502.60000
[Side1] Auto adjustment start - High 519.95000 519.90000
[Side2] Wide/Narrow/Very narrow -
[ ] Shift to panel test mode -
To enter 5 reference level
[ ] -
adjustments
[ ] Writes the adjustment value -
[ ] Go to next adjustment item Back to last adjustment item
[Orange] -
[PTT] Transmit
[0] to [9]
and -
[#], [ ]
*
■ Adjustment item and Display

Aw An Nn Nv
Order Adjustment item Main LCD display Sub LCD display
Adjustment range
1 point ADJ
1 LCD Contrast CNTR -
1~256
Volume 1 1 point ADJ
2 VOL1 (VOL measurement value)
(Counterclockwise Max) 1~256
Volume 2 1 point ADJ
3 VOL2 (VOL measurement value)
(Clockwise Max) 1~256
5 point ADJ
4 RX Assist RAST (CV voltage)
1~4096
5 point ADJ
5 TX Assist TAST (CV voltage)
1~4096
1 point ADJ
6 RTC RTC -
-62~-1/0/+1~+62
- 5 - -
7 High Power HIPWR -
1~1024
- 5 - -
8 Low Power LOPWR -
1~1024
- 5 - -
9 Balance BAL (Encode frequency)
1~256
- - 5 5
10 NXDN Deviation NDEV -
1~1024
Analog Max 5 5 - -
11 ADEV -
Deviation 1~1024
34
NX-300
ADJUSTMENT
Aw An Nn Nv
Order Adjustment item Main LCD display Sub LCD display
Adjustment range
1 1 - -
12 QT Deviation QT -
1~1024
1 1 - -
13 DQT Deviation DQT -
1~1024
1 1 - -
14 LTR Deviation LTR -
1~1024
1 1 - -
15 DTMF Deviation DTMF -
1~1024
Single Tone 1 1 - -
16 TONE -
Deviation 1~1024
1 1 - -
17 MSK Deviation MSK -
1~1024
- - - 1
18 CW ID Deviation CWID -
1~1024
1 point ADJ
19 VOX 1 VOX1 (VOX measurement value)
1~256
1 point ADJ
20 VOX 10 VOX10 (VOX measurement value)
1~256
- 5 - -
21 Sensitivity 1 SENS1 (RSSI measurement value)
1~256
- 5 - -
22 Sensitivity 2 SENS2 (RSSI measurement value)
1~256
5 5 - *1 5
23 RSSI (Reference) RRSSI (RSSI measurement value)
1~256
5 5 - *1 5
24 Squelch Open SQL (ASQDET measurement value)
1~256
5 5 - *1 5
25 Low RSSI LRSSI (RSSI measurement value)
1~256
5 5 - *1 5
26 High RSSI HRSSI (RSSI measurement value)
1~256
5 5 - -
27 Squelch Tight SQLT (ASQDET measurement value)
1~256
Battety Warning 1 point ADJ
28 BATT (BATT measurement value)
Level 1~256
*1: The adjustment of NXDN Narrow is common with the adjustment of Analog Narrow.
35
NX-300
ADJUSTMENT
■ Panel tuning mode flow chart
Panel Test Mode
[ ]
[ ]hold
LCD Contrast Adjustment Item
CNTR LCD Display N/W/VN
[ ]press [ ]hold For all adjustment items, press the
[ ] key to write the adjustment value.
Volume 1(CCW Max)
VOL1
[ ]press [ ]hold
5 reference level Low [ ] Adjustment Point
Volume 2(CW Max)
VOL2 Adjustments L LCD Display
[ ]press [ ]hold [ ]
[ ] Low-Center [ ]
RX Assist 5 reference level
RAST Adjustments L'
[ ] Center [ ]
TX Assist 5 reference level
TAST Adjustments C
Center-High [ ]
RTC
RTC H'
[ ] 5 reference level High [ ]
High Power Narrow
HIPWR Adjustments H
[ ] 5 reference level
Low Power 5 reference level
Narrow Adjustments exit
LOPWR Adjustments
[ ]press [ ]hold
Balance [ ] 5 reference level
Narrow
BAL Adjustments
[ ]press [ ]hold
NXDN Deviation [Side2] NXDN Deviation Very
Narrow
NDEV NDEV Narrow
[ ]press [ ]hold [ ] [ ] 5 reference level
Adjustments
Analog Max Deviation [Side2] Analog Max Deviation
Narrow Wide
ADEV ADEV
Adjustments
QT Deviation [Side2] QT Deviation
Narrow Wide
QT QT
[ ]press [ ]hold
DQT Deviation [Side2] DQT Deviation
Narrow Wide
DQT DQT
[ ]press [ ]hold
LTR Deviation [Side2] LTR Deviation
Narrow Wide
LTR LTR
[ ]press [ ]hold
DTMF Deviation [Side2] DTMF Deviation
Narrow Wide
DTMF DTMF
[ ]press [ ]hold
Single Tone Deviation [Side2] Single Tone Deviation
TONE Narrow TONE Wide
[ ]press [ ]hold
MSK Deviation [Side2] MSK Deviation
Narrow Wide
MSK MSK
[ ]press [ ]hold
CW ID Deviation Very
CWID Narrow
[ ]press [ ]hold
VOX Level 1
VOX1
[ ]press [ ]hold
VOX Level 10
VOX10
[ ]press [ ]hold
Sensitivity 1 [ ] 5 reference level
SENS1 Narrow
Adjustments
[ ]press [ ]hold
Sensitivity 2 [ ] 5 reference level
Narrow
SENS2 Adjustments
[ ]press [ ]hold
RSSI(Reference) [Side2] RSSI(Reference) [Side2] RSSI(Reference) Very [Side2]

Narrow Wide
RRSSI RRSSI RRSSI Narrow
[ ]press [ ]hold [ ] [ ] [ ] 5 reference level
Adjustments
Squelch(Open) [Side2] Squelch(Open) [Side2] Squelch(Open) Very [Side2]

Narrow Wide
SQL SQL SQL Narrow
Adjustments
RSSI(Low) [Side2] RSSI(Low) [Side2] RSSI(Low) Very [Side2]

LRSSI Narrow LRSSI Wide LRSSI Narrow
Adjustments
RSSI(High) [Side2] RSSI(High) [Side2] RSSI(High) Very [Side2]

Narrow Wide
HRSSI HRSSI HRSSI Narrow
Adjustments
Squelch(Tight) [Side2] Squelch(Tight)

SQLT Narrow SQLT Wide
Adjustments
Battery Warning Level
BATT
[ ]press
36
NX-300
ADJUSTMENT
Test Equipment Required for Alignment

Test Equipment Major Specifications
1. Standard Signal Generator Frequency Range 400 to 520MHz
(SSG) Modulation Frequency modulation and external modulation
Output -127dBm/0.1µV to greater than -20dBm/22.4mV
* When performing the Frequency adjustment, the following accuracy is necessary.
• 0.001ppm
Use a standard oscillator for adjustments, if necessary.
2. Power Meter Input Impedance 50Ω
Operation Frequency 400 to 520MHz
Measurement Range Vicinity of 10W
3. Deviation Meter Frequency Range 400 to 520MHz
4. Digital Volt Meter Measuring Range 10mV to 10V DC
(DVM) Input Impedance High input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. High Sensitivity Frequency Range 10Hz to 1000MHz
Frequency Counter Frequency Stability 0.2ppm or less
7. Ammeter 5A
8. AF Volt Meter Frequency Range 50Hz to 10kHz
(AF VTVM) Voltage Range 1mV to 10V
9. Audio Generator (AG) Frequency Range 50Hz to 5kHz or more
Output 0 to 1V
10. Distortion Meter Capability 3% or less at 1kHz
Input Level 50mV to 10Vrms
11. 8Ω Dummy Load Approx. 8Ω, 3W
12. Regulated Power Supply 5V to 10V, approx. 3A
Useful if ammeter equipped
■ The following parts are required for adjustment

Connect the power cable properly between the battery jig
1. Antenna connector adapter
installed in the transceiver and the power supply, and be sure
The antenna connector of this transceiver uses an SMA
output voltage and the power supply polarity prior to switching
terminal.
the power supply ON, otherwise over voltage and reverse
Use an antenna connector adapter [SMA(f) – BNC(f) or
connection may damage the transceiver, or the power supply
SMA(f) – N(f)] for adjustment. (The adapter is not provided as
or both.
an option, so buy a commercially-available one.)
Note: When using the battery jig, you must measure the
2. Nut wrench
voltage at the terminals of the battery jig. Otherwise, a slight
In order to turn the volume nut and the channel selector voltage drop may occur within the power cable, between the
nut, use a recommendation tool. power supply and the battery jig, especially while the
KENWOOD part No. : W05-1123-00 transceiver transmits.
3. Battery Jig (W05-1370-00) SCHEMATIC DIAGRAM
S
1.8M
R1
–
- Terminal (Black)
100P/25V
470P/25V
100µ/25V
C1
C2
C3
+ Terminal – Terminal
+ Terminal (Red) (Red) (Black)
Power cable
Power
supply
37
NX-300
ADJUSTMENT
4. Universal connector • PC tuning
Use the interface cable (KPG-36/36A) for PC tuning or the Connect the wires to the PCB in the connector case of
lead wire with plug (E30-3287-18) and screw (N08-0535-08) interface cable.
for panel tuning. Connect the plug to the universal connector For output the wires out of the connector case, need to
of the transceiver and tighten the screw. process the connector case.
The lead wire with plug (E30-3287-18) and screw (N08- KPG-36/36A
0535-08) terminals are as follows. Numbers are universal
connector terminal numbers.
Caution
1. When connecting the plug to the universal connector of
the transceiver, a short circuit may occur. To prevent this,
be sure to turn the transceiver POWER switch off.
2. Since the RX AF output is a BTL output, there is a DC
component. Isolate this with a capacitor or transformer as
shown in the figure.
3. Do not connect an instrument between red or black and GND. Remove the
screw
Connector case
• Universal connector
100µ 10V
PCB layout 8Ω
+
100µ 10V AF voltmeter
1 : SSW 2 : SP+ +
3 : SP– 4 : MSW 10µ 10V
5 : EMC 6 : ME
+
7 : PTT 8 : PF Audio generator
9 : OPT 10 : E
Shield
11 : 5V 12 : TXD
13 : RXD 14 : NC
• Panel tuning
2 : RED (RX AF OUTPUT)
3 : BLACK (RX AF OUTPUT)
5 : WHITE (MIC INPUT)

SCREW
6 : BROWN (MIC GND)
TUBE
7 : BLUE (PTT SW) GND → ON
8 : YELLOW (PF SW)
10 : BROWN (GND)
11 : GREEN (5M)
BLU (7)
To transceiver PTT SW
BRN (10)
100µ 10V
RED (2)
+
8Ω AF Voltmeter
BLK (3) +
100µ 10V
WHT
(5) +
10µ 10V Audio generator
BRN (6)
38
NX-300
ADJUSTMENT
Radio Check Section
Condition Measurement Adjustment
Item Panel test mode PC test mode Test- Specifications/
Unit Terminal Unit Parts Method
equipment Remarks
1. Frequency 1) CH-Sig : 1-1 1) Test Channel f. counter Panel ANT Check an internal +0.05/+0.55ppm
check PTT : ON Channel : 1 temperature of radio +24.25Hz~
Test Signaling within 25˚C ± 2˚C. +266.81Hz
Mode : Analog @485.1MHz
Signaling : 1
PTT : Press [Transmit]
button.
2. High power 1) CH-Sig : 1-1 1) Test Channel Power Check 4.5W~5.5W
check PTT : ON Channel : 1 meter 2.3A or less
Test Signaling Ammeter
Mode : Analog
Signaling : 1
button.
2) CH-Sig : 2-1 2) Test Channel
PTT : ON Channel : 2
Test Signaling
Mode : Analog
Signaling : 1
button.
Test Signaling
Mode : Analog
Signaling : 1
button.
3. Low power 1) CH-Sig : 1-1 1) Test Channel 0.7W~1.4W
check PTT : ON Channel : 1 1.4A or less
Test Signaling
Mode : Analog
Signaling : 1
button.
Test Signaling
Mode : Analog
Signaling : 1
button.
Test Signaling
Mode : Analog
Signaling : 1
button.
4. MIC 1) CH-Sig : 1-1 1) Test Channel Deviation Panel ANT Adjust AG input to 12.5mV± 5.8mV
sensitivity AG : 1kHz Channel : 1 meter Universal get a standard MOD. Note: The SSW
check PTT : ON Test Signaling Oscilloscope connector terminal (pin 1) of
Mode : Analog AG the universal
Signaling : 1 AF VTVM connector must
AG : 1kHz be connected to
PTT : Press [Transmit] GND when
button. checking MIC
sensitivity.
39
NX-300
ADJUSTMENT
Item Panel test mode PC test mode Test- Specifications/
equipment Remarks
5. Sensitivity 1) CH-Sig : 1-1 1) Test Channel SSG Panel ANT Check 12dB SINAD or
check SSG output Channel : 1 AF VTVM Universal more
Wide: –117dBm Test Signaling Oscilloscope connector
(0.32µV) Mode : Analog
(MOD : 1kHz/± 3kHz) Signaling : 1
Narrow: –117dBm SSG output
(0.32µV) Wide: –117dBm
(MOD : 1kHz/± 1.5kHz) (0.32µV)
(MOD : 1kHz/± 3kHz)
Narrow : –117dBm
(0.32µV)
(MOD : 1kHz/± 1.5kHz)
Common Section
Item Panel tuning mode PC test mode Test- Specifications/
equipment Remarks
1. Setting 1) BATT terminal voltage:7.5V
2) SSG standard modulation
[Wide] MOD:1kHz,DEV:3kHz
[Narrow] MOD:1kHz,DEV:1.5kHz
2. LCD contrast 1) Adj item:[CNTR] 1) Adj item:[LCD Contrast] Panel [Panel Adjust the LCD This item is
Adjust:[***] Press [Apply] button tuning contrast by looking. needed when the
Press [ ] key to store to store the mode] LCD ASSY (B38-
the adjustment value. adjustment value. [ ], 0923-05) is
[ ] replaced.
[PC test
mode]
[ ],[ ]
3. Volume 1) Adj item:[VOL1] 1) Adj item: [Panel tuning mode] This item is
counter- Adjust:[***] [Counterclockwise Turn the volume knob needed when the
clockwise Volume] counterclockwise fully. variable resistor
Press [ ] key to store (R31-0666-05) is
the adjustment value. replaced.
[PC test mode]

Turn the volume knob
counterclockwise fully.
Press [Apply] button to
store the adjustment
value.
4. Volume 1) Adj item:[VOL2] 1) Adj item: [Panel tuning mode]
clockwise Adjust:[***] [Clockwise Volume] Turn the volume knob
clockwise fully. Press
[ ] key to store the
adjustment value.
[PC test mode]

Turn the volume
knob clockwise
fully. Press [Apply]
button to store the
adjustment value.
40
NX-300
ADJUSTMENT
equipment Remarks
5. Assist 1) Adj item:[RAST] 1) Adj item:[Receive Panel [Panel The sub LCD display 2.5V± 0.1V
voltage Adjust:[****] Assist] tuning and [V] indicator on
[RX] 2) Adj item:[L RAST]→ 2) Adj item:[Low] mode] the PC window [PC test mode]
[L’ RAST]→[C RAST]→ [Low’] [ ], shows VCO lock Press [Apply All]
[H’ RAST]→[H RAST] [Center] [ ] voltage. Change the button to store the
Adjust:[****] [High’] adjustment value to adjustment value
Press [ ] key to store [High] [PC test get VCO lock voltage after all
the adjustment value. Press [Apply All] button to mode] within the limit of the adjustment point
store the adjustment value. [ ],[ ] specified voltage. was adjusted.
[TX] 1) Adj item:[TAST] 1) Adj item:[Transmit
Adjust:[ ****] Assist] Note:
2) Adj item:[L TAST]→ 2) Adj item:[Low] Confirm the VCO
[L’ TAST]→[C TAST]→ [Low’] lock voltage
[H’ TAST]→[H TAST] [Center] approximately 3
Adjust:[****] [High’] seconds after the
PTT : ON (RF power [High] adjustment value is
is not output.) PTT: Press [Transmit] changed.
Press [ ] key to store button.
the adjustment value. Press [Apply All] button to
store the adjustment value.
6. RTC 1) Adj item:[RTC] 1) Adj item: [Side1] [Panel tuning mode]
oscillation Adjust:[***] [RTC(Real-time clock)] Press [Side1] key.
frequency After automatic
adjust adjustment adjusted
value is displayed on
LCD.
Press [ ] key to store
the adjustment value.
[PC test mode]

Press [Start] button of
“Auto Tuning”. Press
[Apply] button to store
the adjustment value
after the automatic
adjustment was
finished.
7. Frequency * The Frequency 1) Adj item: SSG Panel ANT [PC test mode] [PC test mode]
adjust adjustment can be [Frequency] Press [Start] button of The value of
performed only in SSG output : -20dBm “Auto Tuning”. Press “IF20” will
PC test mode. (22.4mV) [Apply] button to store become around
(CW (without the adjustment value “0” after the
modulation)) after the automatic adjustment was
Caution: adjustment was finished.
Perform the frequency finished.
adjustment under the
following conditions.
• Temperature range
of +23˚C to +27˚C
(+73.4˚F to +80.6˚F).
(The temperature is
displayed on the
Frequency adjustment
screen of the KPG-
111D and the LCD
of the transceiver.)
• Use an accuracy of
0.001ppm for the
SSG. (Use a standard
oscillator if necessary.)
41
NX-300
ADJUSTMENT
Transmitter Section
equipment Remarks
1. High power 1) Adj item:[HIPWR] 1) Adj item: [High Power Panel ANT Panel [Panel 5.0W ± 0.2W
adjust Adjust:[****] Transmit Power] meter tuning 2.3A or less
2) Adj item: 2) Adj item:[Low] Ammeter mode]
[L HIPWR]→ [Low’] [ ], [PC test mode]
[L’ HIPWR]→ [Center] [ ] Press [Apply All]
[C HIPWR]→ [High’] button to store the
[H’ HIPWR]→ [High] [PC test adjustment value
[H HIPWR] PTT : Press [Transmit] mode] after all
Adjust:[****] button. [ ],[ ] adjustment point
PTT : ON Press [Apply All] button to was adjusted.
Press [ ] key to store store the adjustment value.
2. Low power 1) Adj item:[LOPWR] 1) Adj item: 0.8W ± 0.1W
adjust Adjust:[****] [Low Transmit Power] 1.2A or less
2) Adj item: 2) Adj item:[Low]
[L LOPWR]→ [Low’] [PC test mode]
[L’ LOPWR]→ [Center] Press [Apply All]
[C LOPWR]→ [High’] button to store the
[H’ LOPWR]→ [High] adjustment value
[H LOPWR] PTT : Press [Transmit] after all
Adjust:[****] button. adjustment point
PTT : ON Press [Apply All] button to was adjusted.
3. Balance 1) Adj item:[BAL] 1) Adj item:[Balance] Deviation The sub LCD display 2kHz Tone
adjust *2 Adjust:[***] Deviation meter meter shows the single tone deviation is within
Deviation meter LPF : 3kHz Oscilloscope frequency that DSP ± 1.0% of 20Hz
LPF : 3kHz HPF : OFF generates. The tone tone deviation.
HPF : OFF 2) Adj item:[Low] frequency is alternately
2) Adj item:[L BAL]→ [Low’] switched to 20Hz and [PC test mode]
[L’ BAL]→[C BAL]→ [Center] 2kHz by pressing Press [Apply All]
[H’ BAL]→[H BAL] [High’] [Side1] key on the button to store the
Adjust:[***] [High] front panel or checking adjustment value
PTT : ON PTT : Press [Transmit] [2000Hz Sine Wave] after all
Press [ ] key to store button. check box on the PC adjustment point
the adjustment value. Press [Apply All] button to window while was adjusted.
store the adjustment value. transmitting. Change
the adjustment value
to get same deviation
at 20Hz and 2kHz
within the limit of the
specified voltage.
*2: Refer to the “Mode, Signaling, Necessary adjustment and order” table on page 46.
42
NX-300
ADJUSTMENT
equipment Remarks
4. NXDN 1) Adj item:[Nn NDEV] 1) Adj item:[ Maximum Deviation Panel ANT Panel [Panel 3056Hz 2995~3117Hz
Deviation Adjust:[****] Deviation(NXDN meter tuning
adjust *2 Deviation meter Narrow)] Oscilloscope mode] [PC test mode]
LPF : 3kHz Deviation meter [ ], Press [Apply All]
[Narrow] HPF : OFF LPF : 3kHz [ ] button to store the
2) Adj item: HPF : OFF adjustment value
[NnL NDEV]→ 2) Adj item:[Low] [PC test after all
[NnL’ NDEV]→ [Low’] mode] adjustment point
[NnC NDEV]→ [Center] [ ],[ ] was adjusted.
[NnH’ NDEV]→ [High’]
[NnH NDEV] [High]
Adjust:[****] PTT : Press [Transmit]
PTT : ON button.
Press [ ] key to store Press [Apply All] button to
the adjustment value. store the adjustment value.
[Very Narrow] 1) Adj item:[Nv NDEV] 1) Adj item:[ Maximum 1337Hz 1311~1363Hz
Adjust:[****] Deviation(NXDN
2) Adj item: Very Narrow)] [PC test mode]
[NvL NDEV]→ 2) Adj item:[Low] Press [Apply All]
[NvL’ NDEV]→ [Low’] button to store the
[NvC NDEV]→ [Center] adjustment value
[NvH’ NDEV]→ [High’] after all
[NvH NDEV] [High] adjustment point
Adjust:[****] PTT : Press [Transmit] was adjusted.
PTT : ON button.
Press [ ] key to store Press [Apply All] button to
the adjustment value. store the adjustment value.
5. Analog 1) Adj item:[An ADEV] 1) Adj item:[ Maximum Write the same 2050~2150Hz
Deviation Adjust:[****] Deviation(Analog adjustment value of
adjust *2 2) Adj item: Narrow)] “NXDN Deviation [PC test mode]
[AnL ADEV]→ 2) Adj item:[Low] [Narrow]” for each Press [Apply All]
[Narrow] [AnL’ ADEV]→ [Low’] adjustment point. button to store the
[AnC ADEV]→ [Center] Transmit at each adjustment value
[AnH’ ADEV]→ [High’] adjustment point and after all
[AnH ADEV] [High] check that the Analog adjustment point
Adjust:[****] Press [Apply All] button to deviation is between was adjusted.
Press [ ] key to store store the adjustment value. 2050Hz and 2150Hz.
the adjustment value. Deviation meter
LPF: 15kHz
HPF: OFF
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
[Wide] 1) Adj item:[Aw ADEV] 1) Adj item:[ Maximum Write the same 4150~4250Hz
Adjust:[****] Deviation(Analog adjustment value of
2) Adj item: Wide)] “NXDN Deviation [PC test mode]
[AwL ADEV]→ 2) Adj item:[Low] [Narrow]” for each Press [Apply All]
[AwL’ ADEV]→ [Low’] adjustment point. button to store the
[AwC ADEV]→ [Center] Transmit at each adjustment value
[AwH’ ADEV]→ [High’] adjustment point and after all
[AwH ADEV] [High] check that the Analog adjustment point
Adjust:[****] Press [Apply All] button to deviation is between was adjusted.
Press [ ] key to store store the adjustment value. 4150Hz and 4250Hz.
the adjustment value. Deviation meter
LPF: 15kHz
HPF: OFF
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
*2: Refer to the “Mode, Signaling, Necessary adjustment and order” table on page 46. 43
NX-300
ADJUSTMENT
equipment Remarks
6. QT Deviation 1) Adj item:[An QT] 1) Adj item:[QT Deviation Deviation Panel ANT Panel [Panel Write the value as 0.35kHz± 0.05kHz
adjust *2 Adjust:[****] (Analog Narrow)] meter tuning followings.
Deviation meter Deviation meter Oscilloscope mode] 513 (Reference
[Narrow] LPF : 3kHz LPF : 3kHz [ ], value)
HPF : OFF HPF : OFF [ ]
PTT : ON PTT : Press [Transmit]
Press [ ] key to store button. [PC test
the adjustment value. Press [Apply] button to mode]
store the adjustment value. [ ],[ ]
[Wide] 1) Adj item:[Aw QT] 1) Adj item:[QT Deviation 0.75kHz± 0.05kHz
Adjust:[****] (Analog Wide)]
PTT : ON PTT : Press [Transmit]
Press [ ] key to store button.
the adjustment value. Press [Apply] button to
7. DQT 1) Adj item:[An DQT] 1) Adj item:[DQT Write the value as 0.35kHz± 0.05kHz
Deviation Adjust:[****] Deviation (Analog followings.
adjust *2 Deviation meter Narrow)] 415 (Reference
LPF : 3kHz Deviation meter value)
[Narrow] HPF : OFF LPF : 3kHz
PTT : ON HPF : OFF
Press [ ] key to store PTT : Press [Transmit]
the adjustment value. button.
[Wide] 1) Adj item:[Aw DQT] 1) Adj item:[DQT 0.75kHz± 0.05kHz
Adjust:[****] Deviation (Analog
PTT : ON Wide)]
8. LTR 1) Adj item:[An LTR] 1) Adj item:[LTR Write the value as 0.75kHz± 0.05kHz
PTT : ON HPF : OFF
[Wide] 1) Adj item:[Aw LTR] 1) Adj item:[LTR 1.00kHz± 0.05kHz
PTT : ON Wide)]
44
NX-300
ADJUSTMENT
equipment Remarks
9. DTMF 1) Adj item:[An DTMF] 1) Adj item:[DTMF Deviation Panel ANT Panel [Panel Write the value as 1.25kHz±0.05kHz
Deviation Adjust:[****] Deviation (Analog meter tuning followings.
adjust *2 Deviation meter Narrow)] Oscilloscope mode] 540 (Reference
LPF : 15kHz Deviation meter [ ], value)
[Narrow] HPF : OFF LPF : 15kHz [ ]
PTT : ON HPF : OFF
Press [ ] key to store PTT : Press [Transmit] [PC test
the adjustment value. button. mode]
Press [Apply] button to [ ],[ ]
[Wide] 1) Adj item:[Aw DTMF] 1) Adj item:[DTMF 2.50kHz±0.05kHz
PTT : ON Wide)]
10.TONE 1) Adj item:[An TONE] 1) Adj item:[Single Write the value as 1.50kHz±0.05kHz
Deviation Adjust:[****] Tone Deviation followings.
adjust *2 Deviation meter (Analog Narrow)] 513 (Reference
PTT : ON HPF : OFF
[Wide] 1) Adj item:[Aw TONE] 1) Adj item:[Single 3.00kHz±0.05kHz
Adjust:[****] Tone Deviation
PTT : ON (Analog Wide)]
11.MSK 1) Adj item:[An MSK] 1) Adj item:[MSK Write the value as 1.50kHz±0.05kHz
PTT : ON HPF : OFF
[Wide] 1) Adj item:[Aw MSK] 1) Adj item:[MSK 3.00kHz±0.05kHz
PTT : ON Wide)]
12.CWID 1) Adj item:[Nv CWID] 1) Adj item:[CW ID Write the value as 1.00kHz±0.10kHz
Deviation Adjust:[****] Deviation (NXDN followings.
adjust *2 Deviation meter Very Narrow)] 376 (Reference
[Very Narrow] HPF : OFF LPF : 15kHz
PTT : ON HPF : OFF
45
NX-300
ADJUSTMENT
equipment Remarks
13.VOX 1 1) Adj item:[VOX1] 1) Adj item:[VOX1] AG Panel Universal [Panel tuning mode]
adjust Adjust:[***] AG : 1kHz/45mV at connector After apply signal
AG : 1kHz/45mV at MIC terminal from AG, press [ ]
MIC terminal key to store the
14.VOX 10 1) Adj item:[VOX10] 1) Adj item:[VOX10] adjustment value.
adjust Adjust:[***] AG : 1kHz/3mV at
[PC test mode]
AG : 1kHz/3mV at MIC terminal
After apply signal from
MIC terminal
AG, press [Apply]
button to store the
adjustment value.
15.BATT 1) Adj item:[BATT] 1) Adj item:[Battery Power Panel ANT Press the PTT switch
detection Adjust:[***] Warning Level] meter BATT or [Transmit] button
writing PTT : ON PTT : Press [Transmit] DVM terminal on the PC window.
button. Apply 6.20V to
battery terminal.
Confirm that one
pre-determined
numeric in the range
1 to 256 appears.
[Panel tuning mode]
[PC test mode]
Press [Apply] button
to store the
adjustment value.
16.BATT [Panel test mode] 1) Test Channel Check The transceiver
detection 1) CH-Sig : 1-1 Channel : 1 can transmit
check BATT terminal voltage Test Signaling without causing
: 6.0V Mode : Analog the LED to blink.
PTT : ON Signaling : 1
BATT terminal voltage
: 6.0V
button.
■ Mode, Signaling, Necessary adjustment and order

Necessary adjustment and order
Mode Signaling
Wide Narrow Very Narrow
Analog Audio 1. Balance adjust 1. Balance adjust
-
2. Analog Deviation adjust [Wide] 2. Analog Deviation adjust [Narrow]
QT 1. Balance adjust 1. Balance adjust
2. Analog Deviation adjust [Wide] 2. Analog Deviation adjust [Narrow] -
3. QT Deviation adjust [Wide] 3. QT Deviation adjust [Narrow]
DQT 1. Balance adjust 1. Balance adjust
3. DQT Deviation adjust [Wide] 3. DQT Deviation adjust [Narrow]
LTR 1. Balance adjust 1. Balance adjust
3. LTR Deviation adjust [Wide] 3. LTR Deviation adjust [Narrow]
DTMF 1. Balance adjust 1. Balance adjust
3. DTMF Deviation adjust [Wide] 3. DTMF Deviation adjust [Narrow]
2TONE 1. Balance adjust 1. Balance adjust
3. TONE Deviation adjust [Wide] 3. TONE Deviation adjust [Narrow]
MSK 1. Balance adjust 1. Balance adjust
(FleetSync) 2. Analog Deviation adjust [Wide] 2. Analog Deviation adjust [Narrow] -
3. MSK Deviation adjust [Wide] 3. MSK Deviation adjust [Narrow]
NXDN 1. Balance adjust 1. Balance adjust
- 2. NXDN Deviation adjust [Narrow] 2. NXDN Deviation adjust [Very Narrow]
3. CWID Deviation adjust [Very Narrow]
46
NX-300
ADJUSTMENT
Receiver Section
equipment Remarks
1. AF level [Panel test mode] 1) Test Channel SSG Panel ANT Panel Volume Turn the Volume 0.63V± 0.1V
setting 1) CH-Sig : 1-1 Channel : 1 DVM Universal knob knob to obtain
SSG output : -47dBm Test Signaling AF VTVM connector 0.63V AF output.
(1mV) Mode : Analog Dummy
(MOD:1kHz/±1.5kHz) Signaling : 1 load
SSG output : -47dBm
(1mV)
(MOD:1kHz/± 1.5kHz)
2. Sensitivity 1 1) Adj item:[SENS1] 1) Adj item:[Sensitivity 1] Panel [Panel Write the value as
adjust Adjust:[***] 2) Adj item:[Low] tuning followings.
2) Adj item: [Low’] mode]
[L SENS1]→ [Center] [ ], [L SENS1] / [Low]
[L’ SENS1]→ [High’] [ ] : 120
[C SENS1]→ [High] [L’ SENS1] / [Low’]
[H’ SENS1]→ Press [Apply All] button to [PC test : 135
[H SENS1] store the adjustment value. mode] [C SENS1] / [Center]
Adjust:[***] [ ],[ ] : 145
Press [ ] key to store [H’ SENS1] / [High’]
the adjustment value. : 160
[H SENS1] / [High]
: 173
3. Sensitivity 2 1) Adj item:[SENS2] 1) Adj item:[Sensitivity 2] SSG Panel ANT The sub LCD display
adjust Adjust:[***] 2) Adj item:[Low] AF VTVM Universal shows the RSSI value.
2) Adj item: [Low’] Oscilloscope connector Change the
[L SENS2]→ [Center] adjustment value to
[L’ SENS2]→ [High’] get maximum RSSI
[C SENS2]→ SSG output : value.
[H’ SENS2] -90dBm (7.08µV) (Refer to below)
Adjust:[***] (MOD:1kHz /± 1.5kHz)
The value of the

sub LCD display
SSG output : Press [Apply All] button to NX-300
Adj Point
-90dBm (7.08µV) store the adjustment value.
1 256
Adjustment value
3) Adj item:[H SENS2] 3) Adj item:[High] Write the value as

Adjust:[***] Press [Apply All] button to followings.
the adjustment value. [H SENS2] / [High]
: 245
47
NX-300
ADJUSTMENT
equipment Remarks
4. RSSI 1) Adj item:[An RRSSI] 1) Adj item:[RSSI SSG Panel ANT [Panel tuning mode]
reference Adjust:[***] Reference(Analog AF VTVM Universal After input signal
adjust *3 2) Adj item: Narrow)] Oscilloscope connector from SSG, press [ ]
[AnL RRSSI]→ 2) Adj item:[Low] key to store the
[Analog [AnL’ RRSSI]→ [Low’] adjustment value.
Narrow] [AnC RRSSI]→ [Center]
[AnH’ RRSSI]→ [High’] [PC test mode]
[AnH RRSSI] [High] After input signal
Adjust:[***] SSG output : from SSG, press
SSG output : 12dB SINAD level -3dB [Apply] button to
12dB SINAD level -3dB (MOD:1kHz /± 1.5kHz) store the
(MOD:1kHz/± 1.5kHz) adjustment value.
[Analog 1) Adj item:[Aw RRSSI] 1) Adj item:[RSSI
Wide] Adjust:[***] Reference(Analog
2) Adj item: Wide)]
[AwL RRSSI]→ 2) Adj item:[Low]
[AwL’ RRSSI]→ [Low’]
[AwC RRSSI]→ [Center]
[AwH’ RRSSI]→ [High’]
[AwH RRSSI] [High]
Adjust:[***] SSG output :
SSG output : 12dB SINAD level -3dB
12dB SINAD level -3dB (MOD : 1kHz /± 3kHz)
(MOD:1kHz/± 3kHz)
[NXDN Very 1) Adj item:[Nv RRSSI] 1) Adj item:[RSSI
Narrow] Adjust:[***] Reference (NXDN
2) Adj item: Very Narrow)]
[NvL RRSSI]→ 2) Adj item:[Low]
[NvL’ RRSSI]→ [Low’]
[NvC RRSSI]→ [Center]
[NvH’ RRSSI]→ [High’]
[NvH RRSSI] [High]
SSG output : 12dB SINAD level for
12dB SINAD level for Analog Narrow -3dB
Analog Narrow -3dB (MOD:1kHz/± 1.5kHz)
*3: The “RSSI reference adjust” of NXDN Narrow is common with the “RSSI reference adjust [Analog Narrow]”.
48
NX-300
ADJUSTMENT
equipment Remarks
5. Squelch 1) Adj item:[An SQL] 1) Adj item:[Open SSG Panel ANT [Panel tuning mode]
(Open) Adjust:[***] Squelch (Analog AF VTVM Universal After input signal
adjust *4 2) Adj item: Narrow)] Oscilloscope connector from SSG, press [ ]
[AnL SQL]→ 2) Adj item:[Low] key to store the
[Analog [AnL’ SQL]→ [Low’] adjustment value.
Narrow] [AnC SQL]→ [Center]
[AnH’ SQL]→ [High’] [PC test mode]
[AnH SQL] [High] After input signal
Adjust:[***] SSG output : from SSG, press
SSG output : 12dB SINAD level +1dB [Apply] button to
12dB SINAD level +1dB (MOD:1kHz/± 1.5kHz) store the
[Analog 1) Adj item:[Aw SQL] 1) Adj item:[Open
Wide] Adjust:[***] Squelch (Analog
2) Adj item: Wide)]
[AwL SQL]→ 2) Adj item:[Low]
[AwL’ SQL]→ [Low’]
[AwC SQL]→ [Center]
[AwH’ SQL]→ [High’]
[AwH SQL] [High]
SSG output : 12dB SINAD level +1dB
12dB SINAD level +1dB (MOD:1kHz /± 3kHz)
(MOD:1kHz/± 3kHz)
[NXDN Very 1) Adj item:[Nv SQL] 1) Adj item:[Open
Narrow] Adjust:[***] Squelch (NXDN
2) Adj item: Very Narrow)]
[NvL SQL]→ 2) Adj item:[Low]
[NvL’ SQL]→ [Low’]
[NvC SQL]→ [Center]
[NvH’ SQL]→ [High’]
[NvH SQL] [High]
SSG output : 12dB SINAD level for
12dB SINAD level for Analog Narrow -4dB
Analog Narrow -4dB (MOD:400Hz/± 1.1kHz)
(MOD:400Hz/±1.1kHz)
*4: The “Squelch (Open) adjust” of NXDN Narrow is common with the “Squelch (Open) adjust [Analog Narrow]”.
49
NX-300
ADJUSTMENT
equipment Remarks
6. RSSI at 1) Adj item:[An LRSSI] 1) Adj item:[Low RSSI SSG Panel ANT [Panel tuning mode]
-118dBm Adjust:[***] (Analog Narrow)] AF VTVM Universal After input signal
adjust *5 2) Adj item: 2) Adj item:[Low] Oscilloscope connector from SSG, press [ ]
[AnL LRSSI]→ [Low’] key to store the
[Analog [AnL’ LRSSI]→ [Center] adjustment value.
Narrow] [AnC LRSSI]→ [High’]
[AnH’ LRSSI]→ [High] [PC test mode]
[AnH LRSSI] SSG output : -118dBm After input signal
Adjust:[***] (0.28µV) from SSG, press
SSG output : (MOD:1kHz/± 1.5kHz) [Apply] button to
-118dBm (0.28µV) store the
[Analog 1) Adj item:[Aw LRSSI] 1) Adj item:[Low RSSI
Wide] Adjust:[***] (Analog Wide)]
[AwL LRSSI]→ [Low’]
[AwL’ LRSSI]→ [Center]
[AwC LRSSI]→ [High’]
[AwH’ LRSSI]→ [High]
[AwH LRSSI] SSG output : -118dBm
Adjust:[***] (0.28µV)
SSG output : (MOD:1kHz/±3kHz)
-118dBm (0.28µV)
(MOD:1kHz/± 3kHz)
[NXDN Very 1) Adj item:[Nv LRSSI] 1) Adj item:[Low RSSI
Narrow] Adjust:[***] (NXDN Very Narrow)]
[NvL LRSSI]→ [Low’]
[NvL’ LRSSI]→ [Center]
[NvC LRSSI]→ [High’]
[NvH’ LRSSI]→ [High]
[NvH LRSSI] SSG output : -118dBm
Adjust:[***] (0.28µV)
SSG output : (MOD:1kHz/± 1.5kHz)
-118dBm (0.28µV)
*5: The “RSSI at -118dBm adjust” of NXDN Narrow is common with the “RSSI at -118dBm adjust [Analog Narrow]”.
50
NX-300
ADJUSTMENT
equipment Remarks
7. RSSI at 1) Adj item:[An HRSSI] 1) Adj item:[High RSSI SSG Panel ANT [Panel tuning mode]
-80dBm Adjust:[***] (Analog Narrow)] AF VTVM Universal After input signal
adjust *6 2) Adj item: 2) Adj item:[Low] Oscilloscope connector from SSG, press [ ]
[AnL HRSSI]→ [Low’] key to store the
[Analog [AnL’ HRSSI]→ [Center] adjustment value.
Narrow] [AnC HRSSI]→ [High’]
[AnH’ HRSSI]→ [High] [PC test mode]
[AnH HRSSI] SSG output : -80dBm After input signal
Adjust:[***] (22.4µV) from SSG, press
SSG output : -80dBm (MOD:1kHz/± 1.5kHz) [Apply] button to
(22.4µV) store the
[Analog 1) Adj item:[Aw HRSSI] 1) Adj item:[High RSSI
Wide] Adjust:[***] (Analog Wide)]
[AwL HRSSI]→ [Low’]
[AwL’ HRSSI]→ [Center]
[AwC HRSSI]→ [High’]
[AwH’ HRSSI]→ [High]
[AwH HRSSI] SSG output : -80dBm
Adjust:[***] (22.4µV)
SSG output : -80dBm (MOD:1kHz/±3kHz)
(22.4µV)
(MOD:1kHz/± 3kHz)
[NXDN Very 1) Adj item:[Nv HRSSI] 1) Adj item:[High RSSI
Narrow] Adjust:[***] (NXDN Very Narrow)]
[NvL HRSSI]→ [Low’]
[NvL’ HRSSI]→ [Center]
[NvC HRSSI]→ [High’]
[NvH’ HRSSI]→ [High]
[NvH HRSSI] SSG output : -80dBm
Adjust:[***] (22.4µV)
SSG output : -80dBm (MOD:1kHz/± 1.5kHz)
(22.4µV)
8. Squelch 1) Adj item:[An SQLT] 1) Adj item:[Tight
(Tight) Adjust:[***] Squelch (Analog
adjust 2) Adj item: Narrow)]
[AnL SQLT]→ 2) Adj item:[Low]
[Analog [AnL’ SQLT]→ [Low’]
Narrow] [AnC SQLT]→ [Center]
[AnH’ SQLT]→ [High’]
[AnH SQLT] [High]
12dB SINAD level +6dB (MOD:1kHz/± 1.5kHz)
[Analog 1) Adj item:[Aw SQLT] 1) Adj item:[Tight
Wide] Adjust:[***] Squelch (Analog
2) Adj item: Wide)]
[AwL SQLT]→ 2) Adj item:[Low]
[AwL’ SQLT]→ [Low’]
[AwC SQLT]→ [Center]
[AwH’ SQLT]→ [High’]
[AwH SQLT] [High]
12dB SINAD level +6dB (MOD:1kHz /± 3kHz)
(MOD:1kHz/± 3kHz)
*6: The “RSSI at -80dBm adjust” of NXDN Narrow is common with the “RSSI at -80dBm adjust [Analog Narrow]”.
51
NX-300
TERMINAL FUNCTION
Control unit (X53-4260-XX) Pin No. Name I/O Function
Pin No. Name I/O Function 9 +B O Power output after passing through the fuse
CN1 10 SB1 I Power input after power switch

1 /CS O Chip select output CN404
2 /RES O LCD reset output 1 LED_G O Green LED control output
3 AO O Address bus 0 output 2 /EMG O Key matrix output (Emergency (Orange) key)
4 /WR O WR bus output 3 LED_R O Red LED control output
5 D0 I/O Data bus 0 4 IFC O 50IF switch control output
6 D1 I/O Data bus 1 5 /SAVE O 50C Reg. control output

7 D2 I/O Data bus 2 6 I2CCK O TCXO thermometer clock output
8 D3 I/O Data bus 3 7 /5TC O 50T Reg./switch control output
9 D4 I/O Data bus 4 8 I2CSDA I TCXO thermometer data input

10 D5 I/O Data bus 5 9 SBC O SB3 switch control output
11 D6 I/O Data bus 6 10 /T_R O TX/RX control output
12 D7 I/O Data bus 7 11 TV2 O RX tuning voltage 2 control output

13 VDD O 3.3V LCD power supply output 12 ASSIST O VCO tuning voltage control output
14 VSS - GND 13 TV1 O RX tuning voltage 1 control output
15 VDD O 3.3V LCD power supply output 14 VAGC I AGC voltage input
16 V1 - LCD drive power supply 15 5RC O 50R switch control output
17 V2 - LCD drive power supply 16 TCXO_MOD O TCXO modulation output
18 V3 - LCD drive power supply 17 PGND - GND

19 V4 - LCD drive power supply 18 RSSI I RSSI voltage input
20 V5 O LCD drive power supply 19 PGND - GND
CN23 20 CV I CV voltage input

1 ME - Internal MIC GND 21 AGND - GND
2 EMC I Internal MIC input 22 NC - No connection
3 SP+ O BTL output + for internal speaker 23 NC - No connection

4 SP+ O BTL output + for internal speaker 24 +B I Power input after passing through the fuse
5 SP- O BTL output - for internal speaker 25 +B I Power input after passing through the fuse
6 SP- O BTL output - for internal speaker 26 +B I Power input after passing through the fuse
7 6_/KEYI1 I Key matrix input (KEYI1 for 6-key) 27 +B I Power input after passing through the fuse
8 6_/KEYO2 O Key matrix output (KEYO2 for 6-key) 28 NC - No connection
9 BL_SB O LCD backlight voltage output 29 NC - No connection

10 6_/KEYO0 O Key matrix output (KEYO0 for 6-key) 30 AGND - GND
11 6_/KEYO1 O Key matrix output (KEYO1 for 6-key) 31 PTT I PTT input
12 BL_SB O LCD backlight voltage output 32 Side_G O Key matrix output (SIDE1,2 key)
13 6_/KEYI0 I Key matrix input (KEYI0 for 6-key) 33 Side_1 I Key matrix input (SIDE1 key)
14 AGND - GND 34 W/N O W/N control output
CN403 35 SDO1 O PLL serial data output

1 33A O 3.3V for volume level 36 Side_2 I Key matrix input (SIDE2 key)
2 VOL_GND - GND for volume level 37 /PCS_RF O PLL enable output
3 VOL I Volume level input for audio control 38 /DSW O APC voltage discharge switch control output
4 EN3 I Encoder pulse input 39 APC O APC control output
5 AGND - GND 40 /APCSW O APC switch control output
6 EN4 I Encoder pulse input 41 VCO_MOD O VCO modulation output

7 EN1 I Encoder pulse input 42 THP I Thermistor voltage input
8 EN2 I Encoder pulse input 43 PLD I PLL lock detect input
52
NX-300
TERMINAL FUNCTION
Pin No. Name I/O Function Pin No. Name I/O Function
44 RFAGC O RF AGC control output 22 RXEO O
45 SCK1 O PLL clock output 23 RXEI I Refer to “CN710 26-pin
46 GND - GND 24 TXI I connector specification”
47 S_DET I Battery select input 25 OPT6 O described on pages 56 to 59.
48 GND - GND 26 POW O
49 NC - No connection
50 IF_DET I IF input TX-RX unit (X57-7370-10 A/2)
CN405 Pin No. Name I/O Function
1 SSW I EXT/INT speaker switch input CN900
2 SP+ O BTL output + for external speaker 1 LED_G I Green LED control input
3 SP- O BTL output - for external speaker 2 /EMG I Key matrix input (Emergency (Orange) key)
4 MSW I EXT/INT MIC switch input 3 LED_R I Red LED control input
5 EMC I External MIC input 4 IFC I 50IF switch control input
6 ME - External MIC GND 5 /SAVE I 50C Reg. control input
7 PTT I External PTT input 6 I2CCK I TCXO thermometer clock input
8 PF I Programmable function key input 7 /5TC I 50T Reg./switch control input
9 OPT I/O Option interface I/O 8 I2CSDA O TCXO thermometer data output
10 E - GND 9 SBC I SB3 switch control input
11 5V O 5V output 10 /T_R I TX/RX control input
12 TXD O Serial data output 11 TV2 I RX tuning voltage 2 control input
13 RXD I Serial data input 12 ASSIST I VCO tuning voltage control input
14 NC - No connection 13 TV1 I RX tuning voltage 1 control input
CN701 (for production) 14 VAGC O AGC voltage output
1~20 15 5RC I 50R switch control input
CN710 16 TCXO_MOD I TCXO modulation input
1 OPT1 I/O 17 GND - GND
2 OPT3 I/O 18 RSSI O RSSI voltage output
3 26P_RD I 19 GND - GND
4 26P_TD O 20 CV O CV voltage output
5 NC - 21 GND - GND
6 OPT4 O 22 NC - No connection
7 OPT10 O 23 NC - No connection
8 OPT5 O 24 +B O Power output after passing through the fuse
9 AGND - 25 +B O Power output after passing through the fuse
10 AGND - Refer to “CN710 26-pin 26 +B O Power output after passing through the fuse
11 AI I connector specification” 27 +B O Power output after passing through the fuse
12 AO O described on pages 56 to 59. 28 NC - No connection
13 AGND - 29 NC - No connection
14 5V O 30 GND - GND
15 OPT9 I 31 PTT O PTT output
16 DTI I 32 Side_G I Key matrix input (SIDE1,2 key)
17 OPT8 I/O 33 Side_1 O Key matrix output (SIDE1 key)
18 OPT11 O 34 W/N I No connection (Test pad)
19 OPT7 I/O 35 SDO1 I PLL serial data input
20 OPT2 I/O 36 Side_2 O Key matrix output (SIDE2 key)
21 TXO O 37 /PCS_RF I PLL enable input
53
NX-300
TERMINAL FUNCTION
Pin No. Name I/O Function Option board unit (X57-7370-10 B/2)
38 /DSW I APC voltage discharge switch control input Pin No. Name I/O Function
39 APC I APC control input CN737
40 /APCSW I APC switch control input 1 OPT1 I/O
41 VCO_MOD I VCO modulation input 2 OPT3 I/O
42 THP O Thermistor voltage output 3 26P_RD I
43 PLD O PLL lock detect output 4 26P_TD O
44 RFAGC I RF AGC control input 5 NC -
45 SCK1 I PLL clock input 6 OPT4 O
46 GND - GND 7 OPT10 O
47 S_DET O Battery select output 8 OPT5 O
48 GND - GND 9 DGND -
49 NC - No connection 10 AGND -
50 IF_DET O IF output 11 NC -
CN901 12 NC -
Refer to “CN737 Option board
1 PTT I Internal PTT input 13 AGND -
connector specification”
2 GND - GND 14 5V O
described on pages 60 to 63.
3 Side_G O Key matrix output (SIDE1,2 key) 15 OPT9 I
4 Side_1 I Key matrix input (SIDE1 key) 16 DTI I
5 Side_2 I Key matrix input (SIDE2 key) 17 OPT8 I/O
18 OPT11 O
19 OPT7 I/O
20 OPT2 I/O
21 TXO O
22 RXEO O
23 RXEI I
24 TXI I
25 OPT6 O
26 POW O
Solder Pad
Signal Rating and Condition
Name I/O Function
Type Parameter Min Typ Max Unit
[Output]
PTT2 O Digital PTT output
Output Impedance 10k Ω
[Input]
PTT1 I Digital PTT input VIH 2.8 3.3 V
VIL 0 0.5 V
[Input]
MDSW I Digital Man down switch input VIH 2.8 3.3 V
VIL 0 0.5 V
GND - GND GND Allowable current value mA
VOH(Io=-5mA) 4.0 - 5.3 V
TXD O Digital Serial data output VOL(Io=5mA) 0 - 0.8 V
Baud Rate 19200 bps
VIH 2.8 - 5.3 V
RXD I Digital Serial data input VIL 0 - 0.8 V
Baud Rate 19200 bps
RSSI O Analog RSSI output Output Impedance 10k Ω
54
NX-300
TERMINAL FUNCTION
Universal connector
Signal Rating and Condition
Pin No. Name I/O Function
Type Parameter Min Typ Max Unit
EXT/INT speaker switch input.
VIH 2.8 - 5.3 V
1 SSW I Digital L: External speaker ON
VIL 0 - 0.7 V
H: Internal speaker ON
[ 8Ω load ]
Max output power 1.3 1.8 W
2 SP+ O Analog BTL output + for external speaker. (1kHz, Batt=7.5V)
DC Bias 2.5 V
Allowable Frequency 300 3000 Hz
[ 16Ω load ]
Max output power 0.9 1.4 W
3 SP- O Analog BTL output + for external speaker. (1kHz, Batt=7.5V)
DC Bias 2.5 V
EXT/INT MIC switch input.
4 MSW I Digital L: External MIC ON VIH 2.8 - 5.3 V
H: Internal MIC ON VIL 0 - 0.5 V
Audio Level 7.7 12.5 17.3 mV
(STD deviation)
5 EMC I Analog External MIC input. DC Bias 3.3 V
Input impedance - 1.8 - kΩ
6 ME - - External MIC GND
External PTT input. VIH 2.8 - 5.3 V
7 PTT I Digital
L: PTT ON VIL 0 - 0.7 V
V (PF2 key ON) 2.2 - 2.8 V
8 PF I Analog Programmable function key input. V (PF1 key ON) 1.7 - 2.2 V
V (PF1, PF2 key ON) 1.3 - 1.7 V
Man down input VIH 2.8 - 5.3 V
9 OPT I Digital
Programmable active H/L VIL 0 - 0.7 V
10 E - - GND
5V power supply output Output Voltage 4.9 5.0 5.1 V
11 5V - Power (Output control is FPU (Iout = 100mA)
programmable) Maximum Current - - 0.2 A
VOH (Io=-5mA) 4.0 - 5.3 V
12 TXD O Digital Serial data output. VOL (Io=5mA) 0 - 0.8 V
Baud Rate 19200 bps
VIH 2.8 - 5.3 V
13 RXD I Digital Serial data input. VIL 0 - 0.8 V
Baud Rate 115200 bps
Not used
14 NC - -
(reserved for future option)
55
NX-300
TERMINAL FUNCTION
CN710 26-pin connector specification

Rating and Condition
Pin No. Name I/O Signal Type
Parameter Min Typ Max Unit
[Input]
1 OPT1
VIH 2.8 3.3 V
6 OPT4
VIL 0 0.5 V
8 OPT5 I/O Digital
[Output]
17 OPT8
VOH 2.8 3.5 V
18 OPT11
VOL 0 0.5 V
[Input]
2 OPT3 VIH 2.8 3.3 V
19 OPT7 I/O Digital VIL 0 0.5 V
20 OPT2 [Output]
25 OPT6 VOH 2.8 3.5 V
VOL 0 0.5 V
[Input]
VIH 2.8 3.3 V
3 26P_RD I Digital
VIL 0 0.5 V
Baud rate 19200 bps
[Output]
VOH 2.8 3.5 V
4 26P_TD O Digital
VOL 0 0.5 V
Baud rate 19200 bps
Input Amplitude (Square wave) - 3.3 - Vp-p
Coupling Capacitor - 0.01 - uF
15 OPT9 I Analog
Input Impedance 22k - - Ω
Allowable Frequency 300 - 3000 Hz
Output Amplitude (1kHz, 60% deviation) 0.9 1.3 1.7 Vp-p
Coupling Capacitor 0.1 uF
7 OPT10 O Analog/Digital
Input Amplitude (1kHz, 60% deviation) 0.3 0.5 0.7 Vp-p
11 AI I Analog
Input Impedance - 12k - Ω
Output Amplitude (1kHz, 60% deviation) 30 50 70 mVp-p
12 AO O Analog
Output Impedance - 35k - Ω
16 DTI I Analog
56
NX-300
TERMINAL FUNCTION
Output Amplitude (1kHz, 60% deviation)
while external MIC 160 260 360 mVp-p
while internal MIC - 130 - mVp-p
21 TXO O Analog
Output Impedance - - 2.2k Ω
22 RXEO O Analog
Input Amplitude (1kHz, 60% deviation) 450 640 830 mVp-p
23 RXEI I Analog
Input Impedance 22k Ω
Input Amplitude (1kHz, 60% deviation)
24 TXI I Analog
Output Voltage 5 V
14 5V O Power
Output Current 78 mA
Output Voltage 7.5 V
26 POW O Power
9
Allowable current value
10 AGND - GND 100 mA
(Total current of 3 pins)
13
5 NC - - -
57
NX-300
TERMINAL FUNCTION
CN710 26-pin connector specification

Pin No. Name Device I/O Conection Function
[COR]
Conv/LTR
L: Not activity receiving
H: Activity receiving
[TOR]
Conv/LTR
ANI board O Aux Input H: Activity receiving (Sub Tone or LTR ID is OK)
1 OPT1
[LOK]
Conv
L: TX Complete
H: Not TX Complete
LTR
L: TX Link Complete (until TX finishes)
H: Not TX Link Complete
VGS-1 I BUSY BUSY indication
ANI board I KEY TX requirement input
2 OPT3
VGS-1 I PLAY PLAY indication
ANI board - - -
3 26P_RD
VGS-1 I SO Serial data input
ANI board - - -
4 26P_TD
VGS-1 O SI Serial data output
5 NC - - - -
ANI board O PTT PTT signal output
6 OPT4
VGS-1 O EN Enable
ANI board - - -
7 OPT10
VGS-1 O USEL UART speed select output
ANI board O Emergency Emergency signal output
8 OPT5
VGS-1 O RST Reset output
ANI board - A- GND
9 AGND
VGS-1 - AGND AGND
ANI board - A- GND
10 AGND
VGS-1 - AGND AGND
ANI board - - -
11 AI
VGS-1 I AO VGS Audio input
ANI board - - -
12 AO
VGS-1 O AI VGS Audio output
ANI board - A- GND
13 AGND
VGS-1 - AGND AGND
ANI board - - Note: POW and 5V can not be used simultaneously.
14 5V
VGS-1 O 5C 5V power supply
ANI board I Sidetone Sidetone input
15 OPT9
VGS-1 - - -
58
NX-300
TERMINAL FUNCTION
ANI board I Data Out Data signal input
16 DTI
VGS-1 - - -
ANI board I Tone Control Speaker mute signal input
17 OPT8
VGS-1 - - -
ANI board O Man-Down Man-Down output
18 OPT11
VGS-1 - - -
ANI board I MIC Mute MIC mute signal input
19 OPT7
VGS-1 - - -
ANI board I Aux Output Emergency signal input
20 OPT2
VGS-1 - - -
ANI board - - -
21 TXO
VGS-1 - - -
ANI board - - -
22 RXEO
VGS-1 - - -
ANI board - - -
23 RXEI
VGS-1 - - -
ANI board - - -
24 TXI
VGS-1 - - -
ANI board - - -
25 OPT6
VGS-1 - - -
ANI board O A+ Switched B output
26 POW
VGS-1 - - Note: POW and 5V can not be used simultaneously.
59
NX-300
TERMINAL FUNCTION
CN737 Option board connector specification

[Input]
1 OPT1
VIH 2.8 3.3 V
6 OPT4
VIL 0 0.5 V
8 OPT5 I/O Digital
[Output]
17 OPT8
VOH 2.8 3.5 V
18 OPT11
VOL 0 0.5 V
[Input]
2 OPT3 VIH 2.8 3.3 V
19 OPT7 I/O Digital VIL 0 0.5 V
20 OPT2 [Output]
25 OPT6 VOH 2.8 3.5 V
VOL 0 0.5 V
[Input]
VIH 2.8 3.3 V
3 26P_RD I Digital
VIL 0 0.5 V
Baud rate 19200 bps
[Output]
VOH 2.8 3.5 V
4 26P_TD O Digital
VOL 0 0.5 V
Baud rate 19200 bps
Input Amplitude (Square wave) - 3.3 - Vp-p
15 OPT9 I Analog
Output Amplitude (1kHz, 60% deviation) 0.9 1.3 1.7 Vp-p
7 OPT10 O Analog/Digital
11 NC - - -
12 NC - - -
16 DTI I Analog
Output Amplitude (1kHz, 60% deviation)
21 TXO O Analog
Coupling Capacitor - 0.1 - VuF
60
NX-300
TERMINAL FUNCTION
22 RXEO O Analog
Input Amplitude (1kHz, 60% deviation) 450 640 830 mVp-p
23 RXEI I Analog
Input Impedance 22k Ω
Input Amplitude (1kHz, 60% deviation)
24 TXI I Analog
Output Voltage 5 V
14 5V O Power
Output Voltage 7.5 V
26 POW O Power
9 DGND - GND mA
Allowable current value
10 100
AGND - GND (Total current of 3 pins) mA
13
5 NC - - -
61
NX-300
TERMINAL FUNCTION
CN737 Option board connector specification

[COR]
Conv/LTR
H: Activity receiving
[TOR]
Conv/LTR
ANI board O Aux Input H: Activity receiving (Sub Tone or LTR ID is OK)
1 OPT1
[LOK]
Conv
L: TX Complete
H: Not TX Complete
LTR
L: TX Link Complete (until TX finishes)
H: Not TX Link Complete
VGS-1 I BUSY BUSY indication
ANI board I KEY TX requirement input
2 OPT3
VGS-1 I PLAY PLAY indication
ANI board - - -
3 26P_RD
VGS-1 I SO Serial data input
ANI board - - -
4 26P_TD
VGS-1 O SI Serial data output
5 NC - - - -
ANI board O PTT PTT signal output
6 OPT4
VGS-1 O EN Enable
ANI board - - -
7 OPT10
VGS-1 O USEL UART speed select output
ANI board O Emergency Emergency signal output
8 OPT5
VGS-1 O RST Reset output
ANI board - A- GND
9 DGND
VGS-1 - DGND DGND
ANI board - A- GND
10 AGND
VGS-1 - AGND AGND
11 NC - - - -
12 NC - - - -
ANI board - A- GND
13 AGND
VGS-1 - AGND AGND
ANI board - - Note: POW and 5V can not be used simultaneously.
14 5V
VGS-1 O 5C 5V power supply
ANI board I Sidetone Sidetone input
15 OPT9
VGS-1 - - -
62
NX-300
TERMINAL FUNCTION
ANI board I Data Out Data signal input
16 DTI
VGS-1 - - -
ANI board I Tone Control Speaker mute signal input
17 OPT8
VGS-1 - - -
ANI board O Man-Down Man-Down output
18 OPT11
VGS-1 - - -
ANI board I MIC Mute MIC mute signal input
19 OPT7
VGS-1 - - -
ANI board I Aux Output Emergency signal input
20 OPT2
VGS-1 - - -
ANI board - - -
21 TXO
VGS-1 - - -
ANI board - - -
22 RXEO
VGS-1 - - -
ANI board - - -
23 RXEI
VGS-1 - - -
ANI board - - -
24 TXI
VGS-1 - - -
ANI board - - -
25 OPT6
VGS-1 - - -
ANI board O A+ Switched B output
26 POW
VGS-1 - - Note: POW and 5V can not be used simultaneously.
63
A B C D E F G H I J
1 NX-300 PC BOARD
CONTROL UNIT (X53-4260-XX) -10: K, -11: K3

2
Component side view (J79-0131-19)
3
S13
S4
S3
S2
7
1
*
D2 D1
5 D5
6
S12
S7
S6
S5
8
2
0
7
D6
D10 D9
8
S11
S10
S9
S8
6
3
9
#
R853
R849
R848
9
J79-0131-19
10
Ref. No. Address Ref. No. Address Ref. No. Address

IC1 6K D4 3Q D14 7M
11 IC415 8K D5 5B D15 7L
Q1 7K D6 7B D16 7L
Q2 7L D7 10O D17 9L
Q3 6L D8 10Q D18 4L
Q4 4L D9 7D D19 4L
12
Q5 4L D10 7C D20 8M
D1 5D D11 7L D21 8M
D2 5C D12 7M D22 8L
D3 3O D13 7M D23 9L
13
64
14
J K L M N O P Q R S
PC BOARD NX-300 1

2
Component side view (J79-0131-19)
CN22 D3 D4
C15
D19
D18
Q4
G
S
D
R26
R24
R23
R22
R20
R27 Q5
L2
L1
4
G
S
D
C17
C16
R40
R21
R25
C14 C13 14
1
ME
EMC
SP+
SP+
SP–
SP–
6_/KEYI1
6_/KEYO2
BL_SB
6_/KEYO0
6_/KEYO1
BL_SB
6_/KEYI0
AGND
C5
C6
5
C4
20 V5
CN23 C3 V4
V3
C8 V2
C2 V1
4 3 VDD
VSS
C1
IC1 VDD
R12
G
Q3
S
D7
D
CN1
5 1 R10 D6
D5
R9 D4
R2
TH1
D3
C41
R3
R8 D2
R1 R17
C12
R14
R16
R7 D1
D0
D13 R6
D11
R15 /WR
C11 AO
R5 /RES
R29 1 /CS
R4 C40
Q2
D14
Q1
C28 7
C7 R11
D15 R18
R483
R30
C23
C26
D12
C10
C24 C27 R406

D16
L3
L7
L5
L4
C452
R34 C29
R32 C34
R31 C38
R28 C25
R19 C36
C31
C30
C33
IC415
5 1
4 3
L6
C32
C35
C37
8
D20
D21
D22
R33
R35
R500
D17
D23
CN24
D7 D8
10
Component side
Layer 1
Layer 2
Layer 3 11
Layer 4
Layer 5
Layer 6
Foil side
12
13
65
14
A B C D E F G H I J
1 NX-300 PC BOARD

2
Foil side view (J79-0131-19)
C427
R460
R467
R402
D409
8 R472 C410
5
3 R496 R117
C123
L709
IC409 C429 Q405 R442
IC104
R118 C111
R116 C112
R115 C107
R113
R111
C470
5 1
4 3
L410 5
L711
4 3 1
R457
R447
R474 1 8
1
C445
C449
C440 6 1
C116
C104
R123
R122
R148
R119
R110
R105
C415 + IC413 IC405
L401 R489 R462 R133
4 5
C413
R453
R458
R455
R459
C437
L712
R725
C416 3 4
C438 R490 R495 R471 R132
C424 Q407 R140
R484 R407 5 4
D406
4 R446 4 3 R139
R434
D410 R441 R408
CN101
D405 C430 R497 IC402
C422 6 1 R443 C402 8 1 R194 R193
C418 IC408 R475 1
4 3 8 R147 C120
C447
C450
C439
C417
R424
1 6 5 1 IC412 11 10 R146 R137 C103

R487 B
IC407 4 5 R145 C102
C420 R433 IC102
R431
R425
CN102
3 4 C435 C425 R150 R142
IC401
C Q406 R101
D417
L704 C436 R488 R494 R136 C121

5 L409 C469 C414 C411
L402
E R141 R135
C401
R549 C468
C419
C101
1 5 20 1 C119 C106
R513
R517
R521
R525
R531
R535
R539
R543
IC406 L707 R547 5 4 R128 C105

R127
R502
3 4 IC417 L717
R511
R515
R519
R523
R529
R533
R537
R541
R544
D414 R503 8 1 IC109

Q414
4 3 C453 C464 R546 4 3 C157 R192
49
D102
C117
C113
C109
R131
R129
R126
R143
R121
R107
R103
R102
LED_G
LED_R
/SAVE
/5TC
SBC
TV2
TV1
5RC
GND
GND
GND
NC
+B
+B
NC
PTT
Side_1
SDO1
/PCS_RF
APC
VCO_MOD
PLD
SCK1
S_DET
NC
1
6 + CN401 –
6 1
5 1
C156 R190
Q415 1 8
4 3 R157 R181
TCXO_MOD
CN404 IC418 L705 C158 R187 R183 CN105

/APCSW
6 1
I2CSDA
Side_G
IF_DET
RFAGC
ASSIST
Side_2
I2CCK
R479
VAGC
/DSW
4 5
/EMG
C154
GND
GND
GND
/T_R
W/N
RSSI
THP
R162 C130
IFC
NC
NC
L713
CV
+B
+B
R466 R464
50
2
R159
D415 R156 C148
R130 CN104
Q408
D413
6 1
4 3
R512 R514
R516 R518
R520 R522
R524 C465
R527 R526
R530 R532
R534 R536
R538 R540
R542
4
D411
IC107
R545
X102
C134
R506 C461
R510 C457
R509
R508 C463
R507 C462
R504 C455
R166
C406
C408
R409
L403 + C404 R185 C141
3
C407
R528
7 R172 C153
C459
R501
R161
R160
R165
C460
C456 10
D408
5 4 R180 C146
C451 R498
Q409
R454 R451 C466
C403
IC403
R465
R461
R469
R485 R432 R174

1
R435 R436
R499 C434
C444 R486
G + 1 6 R158
33M
VOL
VOL_GND
EN1
EN4
AGND
EN3
SB1
+B
EN2
8 1
6 1
4 3
R477
R491
1
Q410 D
3 4
1 5
IC410
S 3 4 L8
D412
Q411 IC106
Q401
C454 + C405 14
1
10
SSW
SP+
SP–
MSW
EMC
ME
PTT
PF
OPT
E
5V
TXD
RXD
NC
CN403
C159
L708
8 R470 C428
R482 R480 C432
R481
6 1
4
IC416
C443
R463
CN402 C441
C446
R437
Q403
R138
R449
R448
Q402
3
R444 CN405
1 6
R456
R452
4 3 X101
R439
C448
R493
3 4
C421
G
R445
R450
C442 D
S Q404 IC411
D407
Q413 R438
3 2
C467 C412
R548 L702
R473
4 3
D416
R492 5 1 C143 C136

9 4 1 L714
C409
IC404 C144 C137

R478
IC414
D Q412
G
5 1
S
C431
C433
R404
10
Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No.
IC101 5K IC404 9D IC417 6F IC711 6S Q404 9E Q701 6Q D404 5M D416
11 IC102 5I IC405 3F IC418 6F IC712 6N Q405 3E Q702 4R D405 4B D417
IC103 4K IC406 5C IC701 7Q IC713 4Q Q406 5E Q703 6R D406 4C D701
IC104 3H IC407 5B IC702 5R IC714 5R Q407 4E Q704 7R D407 9D D702
IC105 4L IC408 4C IC703 7P IC715 5P Q408 7C Q705 5O D408 7C D703
IC106 8I IC409 3C IC704 3P IC716 5N Q409 7A Q706 5O D409 3D D704
12
IC107 7I IC410 8E IC705 9N Q101 3K Q410 8A Q707 4N D410 4D D705
IC108 7K IC411 9F IC706 7N Q102 3K Q411 8G D101 3L D411 7A D706
IC109 6G IC412 4D IC707 3P Q103 3L Q412 9D D102 6G D412 8C D707
IC401 5F IC413 3D IC708 9Q Q401 8D Q413 9C D401 4M D413 7A
13 IC402 4F IC414 9A IC709 4R Q402 8C Q414 6C D402 5M D414 6F
IC403 7F IC416 8A IC710 6N Q403 8D Q415 6C D403 5M D415 7F
66
14
J K L M N O P Q R S
PC BOARD NX-300 1

2
Foil side view (J79-0131-19)
C711
C715
R777
IC704
D704
R735
R766 C725
Q102 Q101 C712
C726
C710
R733
R737
R742
5 4
5 1
4 3
R117 R114 R112 R745 R750 3
C114
C798
Q103
IC707
R115 C107
R113
R111
C727
C724
C115 R106 R793
G
S
C717 C722
C766
R829 8 1
+
C756
R765
C767 R758 R755
C732
R701
R703
R705
R707
R709
L710 C118 R108 C108 R753 C745
D101 R414 R847
C797
S C731
R401 R746 C714 R800 D
R415 Q702 G
C795
R846 R842
C704
R770
R769
R403 D703
19
R738 R802
C122
R120
C709
R804
1
R416 R845 R749 C746
R768 R754
R405 R713 C761
R144 S R779
R418 D
C782 C781 R712 1 8 4
C779
IC103
CN101
IC105
4
3 2
IC709
C720
CN701
R815
G
5
R823
R822
C792 R710 4 5
IC713
D401
R836 C790 R832 R830

Q707
1
R797
R837 C793
C777
R410 R852 R851 R818 R807 5 4
R844 R843
4
C103 C124
R838 C794 IC714
20
2
R149 D402 C778 R814
C102 8 1
CN102
R834 C796
G
S
CN702
R805
PTT2
R101
D
R411
R711
R715
R714
R716
R702
Q706
R704
R706
R748 C763
Q705
C788 C786
C705
R736
D403 C706 R806
5
C713 R751 R850
C708 C707
R811 R739
C787
CN703
1 8
PTT1
C789 C791
R833 R835
IC101 R468 R412 C772
C101
IC716 R831 R798

CN103
C106 F701 5 4
C110 4 5
IC715
1 5 IC702 C755
R820 R825
R790 R785 C760

C105 D404
CN704
RSSI
R167 R828 3 4 8 1
L717 R840
R839
C135 R413
C785
D707 D706 C723 C716
1
R743 C804
R841 C744 C775
IC711
CN106
DOWN
CN705
MAN
R803
C157 R192 R427 R740 R816 R812 R747 C734
R102
R154 C759 1 8
C156 R190 R813 R771 6
8
R428
R741 C719
IC712 IC710 13 12
Q701
R155
CN706
R157 R181 1 5
GND
R778
C801
R153 R429 4 5
R187 R183 CN105 R799
C803
C752
R420 3 4 C750 R794 G
R795
C154 Q703 D C753

C145 R787 C749 CN707 S
R156 C148
C762
C802
R752 TXD Q704 C764
R130 CN104 C701
L706
R175 R783
C765
R767
R808
R784
R786
R801 IC703
R809
R810
R756
IC108
R185 C141 R178 C739 R759 CN708 R732 R717

C721 RXD
R172 C153 R177 R417 IC706 7
C740
C735
C738
R775
R796
24 19
TH701
R827
C768
C799
R180 C146 R176 R722 1 18

6 1
4 3
C743
R432 R174
C771
C151 R721
CN712 C758 IC701 R826
R158 C152 R731
L701
R788 C748
CN711
24 1
R789
R782
R729 6
R824
R168 C757 13
7 12
R720
R819
C160 C138 C747 R780 R730
R726
C161
C155 R173 R426

R170 R163 C140
R188 C147
R189 R186
R171 R184 R440
R718
25 OPT6
R719 R728
1 OPT1
R470 C428
D705
C131 C139 R723 8
C737
26P_RD
NC
OPT10
AGND
AI
AGND
OPT9
OPT8
OPT7
TXO
RXEI
D702
R763
C800
R762
R463 R727
R191
R182 R419
+ + C780
C730
CN709
C142
C133
R791 D701 R821

X101 CN710
4
1
C736 R764
R724 C718
IC705
1 5 C742
26P_TD
OPT11
AGND
RXEO
OPT3 2
OPT4
OPT5
OPT2
POW 26
5
L102
DTI
TXI
AO
C143 C136 C149

5V
IC708
C751
4 9
C144 C137 L716 L715 C150 L101 R761
C728
3 4
R757 R744
C703
J79-0131-19
10
Component side
ress Ref. No. Address Layer 1
M D416 9E Layer 2
4B D417 5C Layer 3 11
4C D701 8R Layer 4
9D D702 8R Layer 5
7C D703 4O Layer 6
3D D704 3O Foil side
12
4D D705 8R
7A D706 6O
8C D707 6O
7A
6F 13
7F
67
14
A B C D E F G H I J
1 NX-300 PC BOARD
TX-RX UNIT (X57-7370-10) (A/2)
Component side view (J79-0128-19 A/2)
2
C533
CN500
C649
R529
C630 C646
S
Q504
CV
C628
R541 R537
C651
R649
Q605
C640 R648
3
G
S
D
R652 R651
R530 R531 C534
+ R653
1
C641
4
L503
R641
IC600
C541
R654
Q607
R538
R655
R566
8
C542
4
R656
Q608
C653 R659 S
D505
R533 D
TH600
R660
C637
R539
R657 G
Q610
6 1
4 3
C536
R664
1 5
5 R532 R658
R669
+
C550
C543 C537
IC503 C672
R536
C539
D608 +
3 4 L504
C553
R535
R506
R522
C529
R520
R534
C525
L513
C527
C526
C521
R523
R519
C558
R521
R550
C522
C523
R527 C528
6 +
R554
R555
C631 Q604
Q505
C600
C524 R633
C535
6 1 R670 D605
C519
C518
R513
7 25 R552 C626
C554
C559 C514
C572
IC502
C562 1 8 D604
C512
R515
R549 R635
R512
R567
C602
C517
R511
R546 R547 IC504
R603
Q503 R514
12 19
R548
R602
R601
13 18 4 5
D501 C515
Q507
C516 C513
C511
R504
C555
R557
C520
D518
L598 L599 R600 R629 C622
C601
R712 R704
R574
5
4
IC501
C717 R705
C503
R502
R724 S
R720
R718
R796
8
1
C728 R798
R500
3
1
IC700
C508
C505
CF701
R503 1 24 C727
C502
C500
R501
C902
R714
R904
4
5
R572
R717
C723
C947
C501
R570
CN700
R736
RSSI
C504
C792
R719
9 R505
C709
R738
R794
IC701
C509
X500
C735 C736 R735

C759
R722
R727
3
1
IC500
C710
R726 1 8
L500
4
C722
R792
C711
R721
IC404
R797
C
R731 VAGC
C720
C760
C506 12 13 4 5 R795
10
CN701
C724 R725
R709
R703
C713 C729
C703
11 J79-0128-19 A/2
Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address
12 IC404 10G IC700 8H Q504 3D Q610 5I D501 7B D900 8P
IC500 9B IC701 9E Q505 6C Q704 6L D505 4B D901 5M
IC501 8C IC702 7K Q507 7C Q900 9P D518 7D D902 5P
IC502 7E IC900 4P Q604 6J Q901 7N D604 7J
IC503 5C IC901 9O Q605 3I Q902 7M D605 6I
13 IC504 7H IC902 5N Q607 4I Q904 9O D608 5I
IC600 4J Q503 7B Q608 4J Q905 4N D700 6L
68
14
J K L M N O P Q R S
PC BOARD NX-300 1
TX-RX UNIT (X57-7370-10) (A/2)

Component side view (J79-0128-19 A/2)
2
R647
R645
R642
C946
C640 R648
3
R651
C969
PTT 1
CN901
GND
1
C641
4
Side_G
C945
IC600
R654 Side_1 C971

C943
Side_2 5
R655 C636 C913 TX-RX UNIT
5
C976
R921 4
(X57-7370-10) (B/2)
R920
C963
Q608
1 5
IC900
R661
Q905 R922
3 R659 S
4
D
R927
L900
R660 G TXO
C964
5V
C961
S1
D901
3 RXEO 5
1
OPT9
IC902
R908
+
C956
F900 D902
RXEI
C958
4
6
DTI
R755 C951
C903
C900
D700
TXI
Q604 C957 OPT8
6
R633
C761
Q704 C955
C626
R906 OPT6
OPT11
D604
Q901
R764
D S
G G
S D
R910 POW
7
C977
Q902
5
C766 OPT7
IC702
S D R913
R763
R911
R916
R758
1
R629 C622 G G
R918
R905
OPT1
D S R902
C948 R907 R909 OPT5
C908
C940
C928
C936
C932
C925
C917
C912
R431
S OPT2
C950 + OPT4 8
D900
C941
C938
C934
C930
C926
C919
C915
C910
C906
C904
R432
L901
C949 DGND
OPT3
R904
49 NC
R914
R900
R903
S_DET
SCK1
PLD
VCO_MOD
APC
/PCS_RF
SDO1
Side_1
PTT
NC
+B
+B
NC
GND
GND
GND
5RC
TV1
TV2
SBC
/5TC
/SAVE
LED_R
LED_G
AGND
1 5 OPT10
9
C953
Q904
J79-0128-19 B/2
TCXO_MOD
CN900
C
3 4
Q900
IC901
/APCSW
I2CSDA
Side_G
IF_DET 50
RFAGC
ASSIST
Side_2
B
E
I2CCK
VAGC
/DSW
/EMG 2
GND
GND
GND
/T_R
W/N
RSSI
THP
C974
IFC
NC
NC
C962
+B
+B
CV
C942 C973
C907
R923
10
C939
C935
C931
C927
C923
C922
C920
C918
C972
C916
C905
R928
R901 C967 R926

C914
C966
R925
Component side
C937
C933
C929
R430
Layer 1
Layer 2
Layer 3 11
Layer 4
Layer 5
Layer 6
Foil side
12
13
69
14
A B C D E F G H I J
1 NX-300 PC BOARD
TX-RX UNIT (X57-7370-10) (A/2)
Foil side view (J79-0128-19 A/2)
2
C650
3 C654
C975
R663
L614
C647
C652
C661
R665
R666
C667
L613
R667
TX-RX UNIT
C669
C660
4
(X57-7370-10) (B/2) C668
L611
C665
J79-0128-19 B/2
D607
D606
L612
C666
C663 CN600
5
C664 C662 +
L723
C952
R929
26 POW OPT6 25 D709

C954
C803
TXI RXEI D711
6 R915
RXEO TXO L725
OPT2 OPT7
C810
C809
3
1
IC903
OPT11 OPT8
R790 C850
C849
DTI OPT9
4
5
CN737
5V AGND R791
C811
L726
D710
7 NC NC C799
AGND DGND
C970
C965
C968
OPT5 OPT10 C804 C807 R777
R774
R788 C801
D708
OPT4 NC R773
R786
26P_TD 26P_RD L722
1 5 C780
R762
2 OPT3 OPT1 1 R912 L716
C802 S
C800
8 IC703
R768
C798
Q903
C769
D S
G G
S D
3 4
C783
C794 R785
R772
D706
C777
C779
R761
L721 R775 R769
TXD1 RXD1 R917 C788 C741

C796
C795
L7
L720
R919
9 R778
C789
C742
C
C785
R779
R771 C773 C768
R799
L715
C901
C944 G S
C774
Q705 C782 L714

R765
G D R753 C758 R7
D705 R770 C778 D704
L713
C776
C770
C772
C767
C764
R784 C786
10
C784
Q706 L717 R760

C775
R781
R783
G
S
D
Component side D703

D702
C771 R759
R780 R757 C765
Layer 1
C791
Layer 2
11 Layer 3
Layer 4
Layer 5
Layer 6
Foil side
12
13
70
14
J K L M N O P Q R S
PC BOARD NX-300 1
TX-RX UNIT (X57-7370-10) (A/2)

Foil side view (J79-0128-19 A/2)
2
C645
C650
L610 C643
C547 R544
C648 R545
L508
L607
C642 3
L509
R646 R542 C548
R639
L609
C632 C556
C546
R543
C635
L606
C557
D506
L514
L516
R575
C634
C629
R636
C639
R644
D507
C647
C652
L515
L517
R576
D515
C627
R559
D
R650
4
D510
D514
D Q606 G D517
R561
Q603 S L518
D511
D516
L525
C568 C566 L519
G
L526
C571
C575 C567 C565
L521
C623
C625
R627
R632
R630
R631
5
L605
C579
C574
D519
R634
G
C670
+ L522
L520
Q508
R620
G
D
R599
S
C577
R560
Q509
L603
C570
R628
R626
D
S
C621
Q602
D S
S G
C573 L524
C691 C581 6
C614
R623
R608
C583 C576
C618 L527 C580
C587 Q511
R564
CN902
C615 R622 C689 G

R624
C585
C584
R563
R607
L604
R565
L528
D
L615 C671 C605 S
Q512
C617
C619
Q510 R568
C613
R617 L600
R606 S D
C586
7
C588
C607
C582
R562
C612 L602 C604 G G
R558
Q601
C610 D S
R618 C690 R604
C751
C754
C747
D600 R616
Q600 C578
C611 R605 C603 L523
C753
L709
D601
C755
C749
R742 R612
R609
R610
L710
S C744
L711
8
C756
C712
C708
C707
R744 L780
CN702
C715
C706
BPF
C730
C733
C732
C750 L705
C704 L703
R745
C741 R747 C748 C739 C725

R739 C738
R746
C700
R571
R702
L706 R728
C790
Q700
9
L701
42 G S C719
C740
C752 L704
Q703
R748
L708
G D
R733
C701
C746 XF700
Q701
R743
R701
R750
R753 C758 R752

R749 C743 L707
C734
C764
R740
C745 CF700
10
C721
C737 R737
R730
C718
R710
65
J79-0128-19 A/2 11
IC703 8H Q600 7P Q703 9K D511 4R D601 8O D706 8E 12
IC903 7D Q601 7N Q705 10F D514 4Q D606 5H D708 8E
Q508 5P Q602 6N Q706 10E D515 4P D607 5G D709 6G
Q509 6Q Q603 4N Q903 8D D516 4R D702 10I D710 7E
Q510 7R Q606 4L D506 4P D517 4R D703 10I D711 6F
Q511 6R Q700 9R D507 4Q D519 5R D704 10H 13
Q512 7Q Q701 10O D510 4Q D600 7M D705 10E
71
14
A B C D E
NX-300 SCHEMATIC DIAGRAM

1 LCD
5
6
6
5
/RES
VDD
VDD
VSS
/WR
/CS
V1
D1
A0
V3
D6
D3
D0
V5
D5
V2
D2
V4
D7
D4
CONTROL UNIT (X53-4260-XX) CN1
-7.24V
11
1
20
10
19
18
16
13
3
15
5
12
2
17
14
4
R1
R406
/LCDRST
C1 0.1u
1M C6 1u
C5 1u
C4 1u
C3 1u
C2 1u
100k
R11
LCD CONTRAST 0 IC402
2 R407 TC7WZ245FK-F
100k
R2
IC1
LMC7101BIM5 A 10k 5 4
TH1
100k
B2 GND
-t
220p
6 3
C40
4 3 A B1 A2 /WR
INPUT- INPUT+ R408 7 2
2 33M IC401 G A1 A0
12k
V+ A
R3
TC74LCX245FK 8 1
5 1 3.28V 10k VCC DIR
0.1u
C8
5 V- OUTPUT 11 10
B8 GND 7
12 9
-7.13V A A B7 A8 D0 C402
13 8
100p
C41
B6 A7 D1 0.1u
14 7 A
C405 B5 A6 D2
A 15 6 /CS4
2.2u16 B4 A5 D3
+ 16 5
B3 A4 D4
IC403 17 4 IC401,402
-9.74V LM2682MMX B2 A3 D5
18 3 BUS SW
B1 A2 D6
1 8 19 2
R12 10k
R10 10k
C403
R9 10k
R8 10k
R7 10k
R6 10k
R5 10k
R4 10k
C1- NC oE A1 D7 6
2.2u16 2 7 4.92V 20 1
C2+ C1+ VCC DIR
+ 3 6 R409
C2- VIN C401
4 5 47
VoUT GND
1000p
0.1u
C408
1000p
2.2u16
A L707
C406
C407
0.1u
C404
3
C7
1u
VOLTAGE
+
DOUBLING A A A A A
A
INVERTER
33M
5A
D101,Q101-103 SB2
R417 0 31BU
12KEY BACKLIGHT
∗Q101 12KEY BACKLIGHT SW BLC
2SA1832(GR)F ∗R112 R410 470
KEYO0
R411 470
∗Q102
∗R401
0
∗D5 ∗R403
∗D9 ∗R405
MA2S111-F
1.5k
1.5k
1.5k
KEYO1
∗R114 ∗R117
∗D101
2SC4617(S) R412 470

KEYO2
330 0
∗C114
R413 470
∗D1
B30-2215-05
D401-404
1u
KEYO3
1SS388F
1SS388F
1SS388F
1SS388F
∗C115
∗C108
0.1u
D401
D403
D402
D404
12KEY
CONTROL
470p
∗R106
4.7k
∗D10
∗D6
∗D2
∗Q103 S11 R414

SSM3K15TE(F) /KEYI0
470
0
∗R108
470k
A
4 A 6
A S12 R415 5
/KEYI1 7
D11,Q1-3 470
1 2 3
LCD BACKLIGHT SW
8
Q1 S2 S5 S8 R416
LCD BACKLIGHT
2SA1362-F(GR) R15 /KEYI2
470
4 5 6
0
R402
R404
MA2S111-F
150
150
Q2
D11
2SC4617(S) R16 R17

S3 S6 S9 R144
B30-2215-05
/KEYI3
D3
D7
C11
330 0
1u
0.1u
470
C10
C12 7 8 9
470p
4.7k
R14
D8
D4
S4 S7 S10 S13 R418

Q3 /KEYI4
SSM3K15TE(F) 470
6_KEYO1
6_/KEYI1
6_KEYO0
6_KEYO2
6_/KEYI0
Side_G
Side_1
BL_SB
Side_2
A A
33M
5 9
5
6 6
7 7 7
/WR
/RD
/CS0
/RD
/CS2
A16
6 9
5
D3
D6
D2
D7
D10
D12
D14
D0
D8
D5
D2
D7
D L710
A0
G3
G2
G1
5
E6
E5
E4
E3
E2
E1
E6
E1
F6
F5
F4
F3
F2
F1
F6
F4
F3
F1
6 C118 8
NC
A0
DQ10
A16
DQ0
NC3
DQ8
DQ6
DQ5
oE
CE
CE
VSS2
NC2
VCC2
DQ12
DQ2
DQ2
DQ14
DQ7
DQ7
G1 D6 G4 D6 9
L717
oE A15 A15 A16 A16 VCC1 1u

G2 D5 G5 D1
D9 DQ9 A11 A11 A15 A15 VSS1
G3 D4 G6 C6
D11 DQ11 A19 A19 DQ3 DQ1 D1
G4 D3 H1 C4
VCC A20 A20 A9 A9 A5 A5
G5 D2 H2 C3 6
6 D13
G6
DQ13
IC101
A5
D1
A5 A10
H3
A10 IC103 NC1
C1
C105 D15 DQ15 A1 A1 A11 A11 DQ5 D5
1u 7 SRAM
H1 FLASH C6 H4 B6
VSS1 A14 A14 A12 A12 DQ0 D0
H2 C5 H5 B5 LCONT
C106 D1 DQ1 A10 A10 A13 A13 A7 A7
H3 C4 H6 B4
0.01u D3 DQ3 A21 A14 A14 A4 A4
H4 C3
DQ4
CE2
WE
D4 DQ4 A18 A18

A0
A1
A3
A6
A8
A2
WP/ACC
H5 C2
RESET
D6 DQ6 A6 A6
RY/BY
A1
B1
A3
A6
B3
A5
A2
B2
A4
H6 C1
A13
A17
A12
VSS2 A2 A2
WE
A3
A7
A9
A4
A8
D
A1
A0
A3
A6
A8
A2
A1
B1
A3
A6
B3
B6
A5
B5
A2
B2
A4
B4
D4
1000p
C110
RESET
CN103
/FRST
/WR
/WP
A13
A12
A17
R120
470k
A3
A9
A8
A7
A4
D
5
D
7
X53-4260-XX D1 D2 D5 D6 D9 D10 D101 Q101 Q102 Q103 R106 R108 R112 R114 R117 R401 R403 R405 C108 C114 C115
7 -10 K NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO
-11 K3 B30-2215-05 B30-2215-05 B30-2215-05 B30-2215-05 B30-2215-05 B30-2215-05 MA2S111-F 2SA1832(GR)F 2SC4617(S) SSM3K15TE(F) 4.7k 470k 0 330 0 1.5k 1.5k 1.5k 0.1u 1u 470p
72
X53-426 1/10
F G H I J
SCHEMATIC DIAGRAM NX-300

HD2
5 5 5
6 6 6
X2_CLKIN
15M
33M
33M
33M
SCTAMI
L712
C113
C117
0.1u
0.1u
R102
1000p
470k
R121
C109
R107
100k
100k
L711
R111 100k
R113 100k
R115 100k
R116 47k
R118 47k
5
6
R126 100
R103
D1
1k
D0
D3
D5
D2
D4
A16 MCDIAF
A17 R127 0
M13
G10
G11
G13
G12
C11
C12
C13
D11
D12
D13
H13
H12
H11
H10
N13
B12
B13
E10
E11
E12
E13
K13
K12
K11
K10
F10
F11
F12
F13
L13
L12
J13
J12
J11
J10
BFSX1
X1
CLKMD1
BDX1
D1
X2_CLKIN
TDI
D0
RS
TMS
EMU0
A18
A16
CVSS5
CLKMD3
CVDD3
HPI16
D3
HD3
TDo
D5
HPIENA
TCK
CLKMD2
D2
HD2
A17
EMU1 oFF
D4
DVSS3
TRST
DVDD3
CLKoUT
DVSS2
DVSS4
ToUT
M12
DVSS7
6 N12 R128 0
BCLKX1 MCSCKAF
L11 R135 100k
CVSS8
M11
HD1 FSDET
N11
A13 CVDD5
A19 C119 1u R141 100k
A12
A20 L10
B11 INT3 INT3
CVSS9 M10
A11 INT2
DVDD5 N10
C101 D10 INT1 /DINT
D6 D6 R150 1k
C10 K9
0.1u D7 D7 INT0 /SYMTIM
B10 R142 100k
D8 D8
A10 12
D9 D9
D9 L9
D10 D10 NMI /DWUP
C9 M9 R136 100k
D11 D11 HBIL
B9 N9 11
5 D12 D12 IACK R137 100k
A9 K8
CN102 HD4 BDX2 BDX2
D8 R129 100
D13 D13 L8
C8 BDX0 MCDICN
D14 D14 R143 100k
B8 M8 HD0
D15 D15 HD0
A8 N8
HD5 DVSS6
R101
470k
C102 K7
DVDD4
0.1u C121 0.1u
D B7 R130 100
CVDD6 L7
A7 HRDY
CVSS10 R145 100k
C7 IC102
/RD HDS1 N7
BFSX2
D7 DSP R131 100
DVSS8 M7
A6 BFSX0 /MCCSXCN
/HDS2 HDS2 N6
B6 CVDD4
DVDD6 C120 0.1u
C103 C6 M6
A0 A0 HINT
0.1u D6 L6
A1 A1 CVSS7 R146 100k
A5 K6
A2 A2 BCLKX2 BCLKX2
B5
A3 A3 N5 BCLKX0
7 C5 BCLKX0
CN101 HD6 R147 100k
D5
A4 A4 M5
A4 BDR2 BDR2
A5 A5 L5 R139
B4 HCNTL1
A6 A6 K5 100k
C4 BDR0 MCDOCN
A7 A7 R193 100k
A3
C104 A8 A8 N4
B3 BFSR2 BFSR2
A9 A9 M4
0.1u C3 BFSR0 /MCCSRCN
CVDD7 R194 100k
A2
A21 L4
B2 BCLKR2 BCLKR2
DVSS9 K4 BCLKR0
BCLKR0
D N3
DVSS5
M3 R132
HCNTL0
N2 100k R140
BCLKR1
N1 0
CVSS6 12
MP_MC
MSTRB
IoSTRB
CVDD1
CVDD2
READY
DVDD1
DVDD2
CVSS1
CVSS2
CVSS3
CVSS4
BFSR1
DVSS1
11
HoLDA
HR_W
BDR1
HoLD
R_W
MSC
HCS
HAS
HD7
A22
A10
A11
A12
A13
A14
A15
IAQ
BIo
DS
PS
XF
IS
A1
B1
C1
D1
E1
K1
L1
M1
F1
H1
G1
J1
E3
K3
L3
D3
F3
G3
H3
J3
E2
K2
L2
C2
D2
F2
G2
H2
J2
M2
D4
E4
F4
H4
J4
G4
/MCCSAF
A11
A10
A13
A15
A12
A14
MCDOAF 11
R110
R119
R105
R122
100k
100k
100k
100k
R123
100k
7 12
5
C111
C112
C107
0.1u
0.1u
0.1u
/CS3
C116
/WR
0.1u
BFSX2
/DRST
/HRDY
7 7 7
5RC
8 8 8
9 9 9
LCONT
RESET
BER_EN 13 13 13
LCONT
BCLKR2
BCLKX2
BCLKX2
BFSR2
INT3
BDR2
/SCSS
BDX2
BDX2
SCTXD
RXD0
R701
R711
R703
R706
R709
R710
R713
R705
R715
R702
R704
R707
R714
0
0
R712
0
RESET
20
19
18
17
16
15
14
13
12
11
10
CN701
X53-426 2/10
K L M N O

HD2 HD2
5 GPIo7
6
ASQDET
X2_CLKIN AUD_IREFC
AD12_IREFF
D5
F3
J4
14
31BU
33M
33M
ADC1
IFIR
MICIR
R158 A4
XTALI
22 B4
XTALo
6 A10
32K 32I
A12
CN104 DSPCK
B11
/RINT CKo
A11
USRCKI
H18
5 5 A0 ADD0
J18
6 6 A1 ADD1
K18
A2 ADD2
L18
A3 ADD3
M18
A4 ADD4
N18
A5 ADD5
J17
A6 ADD6
K17
A7 ADD7
M17
A8 ADD8
L713 N17
A9 ADD9
P17
A10 ADD10
R159
IC107 BUFFER K16

22
SM5023CNDH-G A11 ADD11

X102 L16
4 3 A12 ADD12
Q VSS 18.432MHz M16
D A13 ADD13
5 2 C130 3 2 P16
VDD XT oUTPUT GND A14 ADD14
0.01u D J15
6 1 R165 A15 ADD15
XTN INHN K15
4 1 1k A16 ADD16
VCC VC M15
A17 ADD17
0.01u
R162
R166
C134
100k
N15
470k 9.5mV A18 ADD18
6 P15
D D A19 ADD19
L709 J16
A20 ADD20
H15
CN106 ADD21
IC104 G17
R133
TC7SH08FU-F D0 DT0
100k
H16
1 5 2 INPUT D1 DT1
INB VCC AND GATE G15
2 D2 DT2
INA F18
3 4 D3 DT3
HD0 GND oUTY F17
D4 DT4
G16
C123 14 D5 DT5
E18
D6 DT6
D 0.01u E17
D7 DT7
F16
D8 DT8
32K D18
D9 DT9
RTC IC106 D17
RV5C386A D10 DT10
B15
L708 D11 DT11
1 10 D16
32KOUT VDD D12 DT12
9 C15
2 OSCIN D13 DT13
32768Hz
SCL D15
X101
3 D14 DT14
SDA E15
8 D15 DT15
4 OSCOUT A15
INTRB 7 /WR WRITE
BCLKX0 CLKC A16
5 /RD READ
VSS 6 B14
INTRA /RINT LED_R BHE
R138 C14
15 LED_G BLE
C159 47k A13
/CS4 CS4
I2CSDA
D13
I2CCK
D 0.1u /CS3 CS3

32K
C13
/CS2 CS2
B13
18 CN105 CS1
A14
/CS0 CS0
B12
/HRDY HRADY
D14
C122 /HDS2 HDS2
BCLKR0 R18
0.01u TXD0 TXD0
D T18
IC105 7 RXD0 RXD0
R16
XC6109C29ANN RTS0 RTS0
R148
R15
150
3 2 CTS0 CTS0
CD VSS U15
0.01u
C124
AMT TXD1
T15
4 1 R149 33M RXD1
VoUT VIN V15
3.282V 0 26P_TD TXD2
V14
MCSCKCN
3.28V RESET RXD2 RXD2

T14
18 /OINT TXD3
R153
16 100k
SPCS00
SPCS01
SPCS02
SPCS10
SPCS11
SPCS12
11 11
SPCK0
SPCK1
R154
RXD3
ADC4
ADC5
12 12
SPo0
SPo1
SPI0
SPI1
SCK
SDT
15 14 100k
H1
C10
A9
V6
T6
T8
U6
G3
V5
U5
T5
R14
V4
V7
U4
T4
U7
R155 47k
R156 4.7k
R419
0
7 7 R157 4.7k
C160 6800p
5RC
R163 100k
5RC
R161
R160
S_DET
SDO1
SCK1
8
0
W_/N
TONESW
9
CV
/EVCS
SDO0
/WP
LCONT
STSW
SCK0
LCONT I2CCK
RESET I2CSDA
/PTT A
/PTT 14 14
RSSI 15 15
7 7
33MAS
13 11
33A-1
18
I2CSDA
12
I2CCK
RXD3
8
16 16
9 18 18
11 11
13
/MNDNU
SPCS10
RXD RESET
TXD
R716
A
0
12 12
PTT1
RSSI
MAN
RXD
TXD
CN703
DOWN
GND
CN706
CN708
CN705
CN702
PTT2
CN704
CN707
8 8
9 9
13 13
X53-426 3/10
9
14
12
16
11
HD2
13
15
18
33A-1
GPIo7
33MAS
RESET
SPCS10
7
H2
VOX ADC6
H3
VOL ADC7
J1
17
BATT ADC8
J2
PFKEY ADC9
P
C131 0.1u J3
A
MICVR
17
C133 10u6.3
A
+ K1
RXAF SPDAC
K2 T1
MIC MICADC0 NC30
K3 N4
MOD MoDDAC NC29
L2 T17
NC MICADC1 NC28
T10 T16
8
/KEYI0 KEYI0 NC27
R9 R13
/KEYI1 KEYI1 NC26
V11 F15
BLC
/KEYI2 KEYI2 NC25
U10 C18
/KEYI3 KEYI3 NC24
T11 C16
/KEYI4 KEYI4 NC23
V12 D6
/KEYO0 KEYo0 NC22
U11 D4
/KEYO1 KEYo1 NC21
T12 B16
/KEYO2 KEYo2 NC20
V13 C5
/KEYO3 KEYo3 NC19
U12 C3
KEYo4 NC18
Q
R4 A3
BEEP PWM1 NC17
P4 V2
TONE PWM2 NC16
V8 V1
32K TI NC15
U2
NC14
R10 U1
TDI NC13
V18
R12 NC12
TMS V17
NC11
U18
R11 NC10
TDo U17
NC9
T13 B18
TCK NC8
B17
NC7
7
U14
TRST A18
NC6
15
A17
U13 NC5
RTCK B2
NC4
B1
H17 NC3
BSCAN0 A2
ASIC
IC108
NC2
E16 A1
18
R
13
BSCAN1 NC1
A
9
E6
17
14
12
16
11
AGND9
R167 P18 L1
RST AGND8
C135 1k K5
AGND7
J5
D
1000p R17 AGND6
/FRST RSTo H5
G18 AGND5
TEST0 G5
L17 AGND4
TEST1 F5
N16 AGND3
TEST2 E5
L15 AGND2
R168 TEST3 U3
0 V3 NC34
M1
D
BooT
C2 AVCC10
ASQAPC SQDAC L3
F1 AVCC9
RSSI ADC0 K4
F2 AVCC8
RFAGC DAC0 T3
E1 NC35
IFR H4
G2 AVCC6
VAGC ADC3 G4
G1 AVCC5
THP ADC2 F4
R170 AVCC4
V16
S
NC36
10k E4
AVCC2
15
C161 D3
AVCC1
A
6800p U16
SCHEMATIC DIAGRAM
D2 DGND15
ASSIST FCDADC C17
DGND14
T2
E2 DGND13
IFADCP C4
C140 E3 DGND12
IFADCN A5
0.1u D1 DGND11
IFVR B3
A
C142 DGND10
P7
10u6.3 DGND9
P8
A
+ DGND8
P12
R463 DGND7
P13
100k DGND6
K14
C428 DGND5
J14
DGND4
3p
68k
R470
T
12
13
18
9
17
14
GPIo7
15
16
IFADCN
HD2
33MAS
11
BLC
SPCS10
33A-1
33A-1
NX-300
X53-426 4/10
U V W X Y

HD2
GPIo7 C459
L101 470p 19
33A-1 C460
15M
33M
33A
L102 VOL SW/ENC
C136 0.01u
C138 0.1u
C139 0.1u
6800p
C137 1u
A
D A C461 VR1
POWER SW/AF VOL
E12 470p
DGND3 A
E11 CN403
DGND2 R501 33A 1
E10 33A
DGND1 A 2.2k
L5 L714 R506 VOL_GND 2
DVDIo7
P6 L403 2.2k
C143 0.01u
VOL 3
C145 0.1u
C146 0.1u
C147 0.1u
C148 0.1u
L716
C144 1u
DVDIo6 VOL
P11 S1
DVDIo5 R510 EN3 4
L14 ENC3 CHANNEL SELECTOR
DVDIo4 1k R509 7
H14 AGND 5
DVDIo3 8
E13 R508 A 1k EN4 6
DVDIo2 D ENC4 9
E7 1k
DVDIo1 R507 EN1 7 4
M5 L715 ENC1 19
DVDD10 R504 1k 5
N5 EN2 8
C149 0.01u
C151 0.1u
C152 0.1u
C153 0.1u
C154 0.1u
C155 0.1u
ENC2
C150 1u
DVDD9 6
P9 1k +B 9
DVDD8 1
P10
C463
C455
C462
C457
470p
470p
470p
470p
DVDD7 SB1 10 2
N14 17
DVDD6 3
C456
470p
M14 A A A A
DVDD5 D
G14
DVDD4 A
F14
DVDD3
E9
DVDD2 R174
E8
DVDD1
SB1
B5 100k
GPIo11 DSR
C6
GPIo10 SBC 19
B6
GPIo9 5UC
BATT
+B
A6
GPIo8 EXAMT
U8
GPIo7
33M
33A
R8
GPIo6
R7
GPIo5 INAMT
T7 R175 100k
GPIo4
L705
V10 D 16
GPIo3 ENC4 R176 100k 19
U9
GPIo2 ENC3 R177 100k 14 REVERSE
BATT
V9 CURRENT
GPIo1 ENC2 R178 100k PREVENTION
T9
GPIo0 ENC1 17
R181 100k D102 20
C11
SIMRST /MNDNU 1SS416
4
D12 R192
SIMCK /PSW
/PCS_RF
VCC
oUTY
C12 R190 1k IC109
SIMDT /BINT
TC7SH08FU-F
1000p
1000p
R5
0.01u
1k
C156
C158
C157
17
SYMTIM /SYMTIM
R6 2 INPUT
FSDET FSDET
GND
D D AND GATE
INB
INA
R2
TXRVE /5TC 15
P3
TRAMP DSW
1
3
2
P2
TMoD /LCDRST
M4 12 D
PSTPA /APCSW
R186
R189 R188
R184
47k
47k
47k
15
R1 R171 21
100k
PSTIF 14
TCXO_MOD
0 D VCO_MOD
N3
TV1
/EVCS
TV2
SDO0
SCK0
PSTPLL MM 15
N2
RXRVE /SAVE
P1
T_/R
R752 100
R756 100
R759 100
RXSLT
R427 0
R428 0
L4
R429
PSRRF 5RC 14
0
M2
PSRIF IFC
M3
PSRPLL
N1
R191
470k
RSSIT /DRST
12
11
10
6
5
4
3
2
1
D8
VFRM /DWUP
VIN1
VoUT1
DI
VDD
LD
VIN3
CLK
VIN2
VIN4
VoUT3
VoUT2
D
VoUT4
D7
C740 1000p
VoINT /DINT
C743 1u
C7 20
MCo2 /UDET
VDAREF
D10 R187
RESET
VoUT5
VoUT6
VoUT7
VoUT8
MCCS2 /EMG
VIN5
VIN6
GND
VIN7
VIN8
C8 R172 0 1k
D0
MCCK2 PLD
D9
R180 100k
R183 100k
R185 1M
MCCR1 /MCCSRCN PLD

21
20
13
16
18
19
23
15
22
14
17
24
B7
MCCX1 /MCCSXCN 24
C9
R740
MCo1 MCDOCN 23
1000p
0
C738
B8 D
MCI1 MCDICN
A7
MCCK1 MCSCKCN
B10 IC703 A
C141
100p
MCCS0 /MCCSAF M62364FP-F

B9 7
MCo0 MCDOAF D/A 18
D11 D CONVERTER
MCI0 MCDIAF
A8
MCCK0 MCSCKAF
R3 R173
AGCDAC /SCSW
R182
470k
0 LCONT
21
IFADCN D
15 14
11
12 16 14
15
14 14 14
7
33MAS
33A-1
15 15
17
16 16 16
18 18
11
21
17
SPCS10
IFADCN
12
BLC 18
9 9 9
13 13 13
X53-426 5/10
Z AA AB AC AD

19 19 19
33A
5A
D702 R819
PLD
MA2S111-F 10k
R785
6.8k
R790 PLD
1k CONTROL
ASQDET
Q701 R798 100k
C719 2SA1832(GR)F
OPT10 C755 47p
0.1u
R741
470k
OPT SW R803
10k
A R747
ASQ DET A
4
3
2
1
33k
VSS
IN-A
IN+A
oUTA
ASQAPC NOISE
IC711
0.01u
R810
C802
DETECTOR
3.3k
R743
TC75W51FK(F)
10k
0 01u
C760
D705
SQL BPF/ A RB706F-40 R824
oUTB
R739 C716 BPF/SQL DC AMP 39k
IN+B
VDD
IN-B
R809 C771
82k 680p
R826
C707
330k
27p
330k 0.22u
8
5
7
C723 C764
R821 100k
C780 0.22u
0.1u 1000p
1000p
C768
R827
180k
A Q704
C734 C804 C752 100p R799 2SC4617(S)
4
3
2
1
C706
68p
1000p 47p 330k
R771
TH701
R778
VSS
IN+A
IN-A
C753 100p
oUTA
100k
15k
33k
C765
R808
0.1u
470
-t
14 IC702
TC75W51FK(F) A A
APC LPF A A A
oUTB
IN+B
VDD
IN-B
1000p
C803
W/N
APC/ASQ SQL
NOISE SW
SMF NOISE AMP
6
8
5
Q703
SSM3K15TE(F)
R736 C713 R751 R850
82k 3300p R748 0 0
A
10k
18
24
20 20 20
22
14 14
AMT TXO
R426
/SCSW
0
C726 IC713 C777
RXAF SMF 0.1u TC75W51FK(F) 1000p
A SCSW(RXAF)
C761 5 4
R793
RX AF LPF IC704 IN+B VSS

1k
23 14 TC75S51FE(F) RF AF SW 10p C778

6 3 A
IN-B IN+A
1200p
1 5 7 2 1u
C714
IN+ VDD IC707 oUTB IN-A

TC7W53FK(F) 8 1 R818
2 VDD oUTA
VSS 5 4
A GND 100k
R804
R802
22
470k
C709 R738 R746 3 4 R766 6

0
R815
3 A:VREF
100k
RXAF IN- oUT CH1
1u 56k 56k 0 7 VEE /B:RX SUM
CH0 2
C725 8 INH C779
VCC 1 C756 R800
CoMMoN
R753 180p 0.1u 470k 0.01u
1.65V REF/
C745 RX SUMMING AMP
C711 68k
RXEO 0.01u
0.1u A
C715 R777
RXEI
R735 R750 0.1u C727 R765 47k
BEEP
47k 10k 0.1u 330k
0.01u
0.01u
C712
R745
C724
6.8k
A A A 22 22
1
2
R779 VGS REC SEL OPT SW

C720 R754 R768 47k
OPT9
0.01u 560k 220k A
4
3
2
1
SIDE TONE MUTE

0.01u
C763
CoMMoN
INH
GND
VEE
C704 C731 R769

AI
0.1u 0.01u 330k IC709
IC714
TC7W53FK(F)
TC7W53FK(F)
R733 R742 C722 R755 C732 R770 1 8
TONE CoMMoN VCC
47k 10k 0.01u 100k 0.01u 330k 2
VCC
CH1
CH0
INH 7
CH0
0.01u
0.01u
C710
A
C717
R758
R737
3
15k
10k
VEE 6
CH1
6
8
5
14 4 5 R797
A A A GND A
1k
R749 TONE SW R805 R814
TONESW C746
4.7k Q702 47k 560k
SSM3K15TE(F) 0.01u
A A R806
STSW 47k
14
R811
R807
82k
OPT6
C705 1k
AO
W_/N
0.1u C708
APC
TXO
0.1u
15
23
16 16 16
15 15 15
21 21 21
23 23 23
IFADCN IFADCN
10
18 18 18
9 9 9
13 13 13
X53-426 6/10
AE AF AG AH AI

19 19 19
33A
33A
+B
5A
R : 5.14V
Q406
Q406,407 2SB1132(Q,R) R471
VOLTAGE
1000p
0
C449
C425
C445
REGULATOR
0.1u
1u
(AF AMP)
R441
15k
Q407 R496 100k
R472
UMG3N
22k
Q405
AUDIO IC413
AF AMP SW AMP TPA6201A1DRBR
1 8 SP-
R459
R443
SHUTDoWN Vo-
470k
C429
R474
0.1u
33k
Q405 1k 7
A SSM6N16FE-F C440 0.1u 2 GND
BYPASS
C437 R489 6
D409 3 VDD
IN+
0.22u 22k 5 SP+
MA2S111-F 4 Vo+
A IN-
R442
R462
R447
R457
100k
100k
1k
1k
SP CONTROL
C438 R490 R495
A D410 0.22u 22k 100k
INAMT MA2S111-F R484
EXAMT
1000p
22k
C450
C447
1u
R460
SP DRIVE
1k
0.01u
C420
AF AMP R497 100k

R455
IC408
1k
7
6
5
TC75S51FE( F) AUDIO IC412
CoNT1
VCC
TPA6201A1DRBR
oUT_IN2
IN_oUT2
R467
AMP
100k
R433 1 5 IC409
IN+ VDD TC7W66FK-F 1 8
0 SHUTDoWN Vo-
2
C430
R475
0.1u
AF SW
33k
VSS
IN_oUT1
oUT_IN1
A 3 C439 0.1u 2 7
C424
CoNT2
4 BYPASS GND PGND

IN- oUT
GND
0.01u
C427
0.1u C435 R487 3 6

IN+ VDD
R446 270k 0.22u 22k
1
4 5
3
2
A IN- Vo+
C422 10p
A
R434
R458 C436 R488 R494

R453
100k
39k
100k 0.22u 22k 100k

20 19
23
EXTSP+
EXTSP-
22 22 22
14 14
1
2
ME
TXO
MIC
MOD
C757 CN711 D707

DA221 VOX
R764 22k 4.7u
R786
/SCSW
MM
VOX
0
R796 C758 CN712

R813
R763 22k R784

27k
MODULATION
R831
470k
LPF R762 C730 100k 33k 4.7u DI DETECTOR
C749
R794
100k
47p
0.022u
C801
R812
1500p
22k 330p
C800
5.6k
MOD SMF C775 D706 C789 R835 C791

R828 RB706F-40
47p 0 68p 15k 0.039u
A C787
A R816 R833
0.22u
C785
R825
100k
1u
68k A : MIC SUM1/
4
3
2
1
680k B : VOX
IC715
VSS
IN-A
IN+A
TC75W51FK(F)
oUTA
8
7
6
5
IC710 TC75S51FE(F)
R820
10k
TC75W51FK(F) A
VDD
oUTB
IN-B
IN+B
4 3
IC705
C736
0.1u
oUT IN-
1500p
R840
C718
MOD/MIC
0.01u
C744
8
7
6
5
SUMMING AMP 2 IC716

oUTB
IN+B
VSS 12k
VDD
oUTB
IN-B
IN+B
TC75W51FK(F)
VDD
IN-B
5 1
oUTA
R841
IN+A
A : MOD SUM/ VOX AMP 560k

2 IN-A
VSS
VDD IN+
B : MIC SUM2
6
8
5
0.01u
C786
GND
1
C772
3
4
oUTA
IN+A
IN-A
VSS
R744 R757 C728 0.01u

A A
1
22k 22k 330p

3
2
C750 VOX AMP

R761
47p
R795
A R839
0
22k
C721 R767 10k R783 R787 R801 C762
R830 33k
0.1u 18k 120k 47k 0.1u
C735 1M
DETECTOR MIC AGC
1200p
D703 Q705 C788 R832 C790 R836 C792
MIC AA IC706 2SC4738(GR)F
A RB706F-40 15p 47k 0.1u 47k 1u
TC75S51FE(F) R822
3
R775
MIC AMP 18k R837 C793
oUT/IN
GND
4 3
IN/oUT
10k
TC7S66FUF
oUT IN-
0.01u
C759
C766
C781
R851
0.1u
68k
68k 0.1u
6800p
1u
C739
IC712
2
VSS
R789
150k
R834 R838 C794

CoNT
5 1
VCC
R829
VDD IN+ D704 0 560k 0.1u

C782
R852
C767
68k
0.1u
1u
0
R788
RB706F-40
47k
C747
0.1u
C799 A
5
4
R823
0.1u A
10k
R440
R780
R782
Q706
100k
100k
0
C748
0.1u
DETECTOR
2SA1832(GR)F
A MM
SCSW(MIC)
C737
0.1u
MIC SW
19
16 16 16
15 15 15
21 21 21
TXI
DTI
23 23 23
IFADCN IFADCN
18 18 18
9 9 9
13 13 13
X53-426 7/10
AJ AK AL AM AN

SWITCH UNIT (X41-3720-10)
CN23
AGND 14
R20 1k A 6_/KEYI0 13
6_/KEYI0
R21 1.2k BL_SB 12
BL_SB
R22 1k 6_KEYO1 11
6_KEYO1 6KEY
R23 1k 6_KEYO0 10
6_KEYO0
R25 1.2k BL_SB 9
R24 1k 6_KEYO2 8
6_KEYO2
R26 1k 6_/KEYI1 7
9 6_/KEYI1
SP- L1 SP- 6
SP
100p
C16
D18
D18,19
HZC6.8-E
SP- 5
SURGE
ABSORPTION SP+ 4
100P
A A
D19
C17
SP+ L2 SP+ 3
R40 EMC 2
470p
0
C13
ME 1 MIC
R846
33A
470
0.01u
C795
470p
C14
R847
1.8k
10u10
C798
R845
R842
MIC
100k
100k
SHIFT A
A SW
A
Q707 3.32V Q5
2SJ243-A 2SJ347F
C797
1u CN22 CN24
100k
R27
MIC
MUTE
R844
4.7k
A
R843
PTT RF OPT EMC MSW SSW
1k
C796
0.1u
MIC CONTROL CONTROL

SHIFT
CONTROL
A A
C23 1000p
C24 1000p
C25 1000p
C26 1000p
C27 1000p
C35 1000p
C37 1000p
C28 100p
C32 100p
Q4
NNCD6.8G-A
NNCD6.8G-A
SSM3K15TE(F)
470p
C15
D21
D20
D12-16
REVERSE A A
CURRENT PREVENTION CN405
R29 1
SSW
EXTSP+ 1k L4 2
SP+
EXTSP- L5 3
SP-
D12 R28 4
MSW
UNIVERSAL CONNECTOR
1SS416 1k R30 L6 5
EMC
ME 100 L7 6
ME
R31 7
PTT
1k 8
PF
1SS416
R32
D14
9
9 OPT
D414 100 L8 10
5V E
VOLTAGE REGULATOR (50U) TX LED SWITCH L3 A 11
+B 5V
5
R35 12
TXD
VIN
1SS416
VoUT
R503 D414 R33 100 13

D13
RXD
NJM2880U105ZB
10k 1SS416 R34 100 14

NC
NoISEBYPASS
IC411
100
C446
EMZ6.8N
C36 6800p
C29 100p
C30 100p
C31 100p
C33 100p
C34 100p
C38 100p
1u
DA221
DA221
R502
D23
CoNTRoL
D22
D17
C441
1u
10k
R547
1k
GND
1SS416
D15
7
6
5
C443 3
2
TC7WH126FK
A
Y1
VCC
A2
G2
0.01u
D17
IC417
SURGE D22
IC417
A ABSORPTION RXD CONTROL
GND
DUAL BUS
G1
A1
Y2
5
BUFFER D23
A
TC7SET08FU-F
VCC
oUTY
IC418 TXD CONTROL

3
2
4
SSM6N16FE-F
TC7WH125FUF
0.01u
C452
IC415
C453
Q411
1 8
0.01u G1 VCC
GND
A 2
INB
INA
A1 7
G2
R546
3
1k
A 6
1
Y2
3
2
Y1
1SS416
4 5
D16
R500 A GND A2
1SS416
R491
100k
D415
47k RX LED
SWITCH C464
R483
47k
IC415 A 0.01u
BER_DATA
R19
470
BER_CLK
BER_EN
2 INPUT
BER_EN
DUAL BUS
SCTXD
BFSX2
/SCSS
AND
RXD0
BUFFER
TXD
RXD
Q411 GATE
R468
R478
8.2k
R18
0
LEVEL
CONVERTER 13
PFKEY
/UDET
RXD3
TXD0
RXD0
CTS0
RTS0
/PTT
DSR
5UC
16
R477
MM
0
9 16
33M
5A
19 19 19
16
15 15 15
21 21 21
13
23 23 23
IFADCN IFADCN
18 18 18
9 Side_1,Side_2,Side_G 9 9
13
X53-426 8/10
AO AP AQ AR AS

D405,406,IC407
+B
33M DC/DC CONVERTER
VOLTAGE L402
CONTROL +B
REGULATOR (33M) L410 L401
D416
IC404 22u
XC6204B332M
HRB0502A
1000p
1SS388F
4
C470
C417
R424
220p
68k
R438
D406
R548
VIN
SHDN
4 3
SW
3.284V NC CE 3.82V
C419
4.7u
100k
1SS388F
2 47k
D405
VSS
10u10
C416
C415
33M
+
IC407
10u
BooST
L702 R456
5 1
GND
LT1616ES6-PBF
1000p
0.01u
R431
C418
C469
33M VOUT VIN
470k
FB
470k
R452
470k
R439
0.01u
C409
C412
C467
R425
1u
1u
SB1
33k
1
3.82V 100k
3
2
Q402
SSM6N16FE-F A
A
L409
IC405 LEVEL CONVERTER
1.5V 3.82V R435
VOLTAGE REGULATOR (15M) A
R725 100k
15M
10
5
15M R454
XC6205B152PRN
VIN
VoUT
R451
470k
470k
R436
C410
C413
10u
1u
IC405
100k Q401
VOLTAGE REGULATOR (5A) SSM6N16FE-F A
VSS
NC
CE
4.99V IC708 7.5V

XC6204B502PR
1
3
2
4
5A
A SB2 SW
VIN
VoUT
IC406 33A 7.55V Q403
SB2
C742
VOLTAGE REGULATOR (33A) CONTROL 2SA1955A-F
C751
1u
1u
D417
R449
IC406
470k
VSS
MA2S111-F
NC
CE
XC6204B332M 1SS388F
D407
REVERSE
4 3 R549
1
CURRENT
3
2
NC CE
R448
R444
560k
PREVENTION
10k
2 47k
VSS Q404
33A A
L704 SSM3K15TE(F)
R791
5 1 R437
470k
1SS301F
33A VOUT VIN
D701
3.31V 470
0.01u
C468
C414
5A SW
1u
6800p
C421
A
R450
R445
3.82V
470k
150k
C411
1u A
5A A A A
SB2 SB2 SW CONTROL
SBC
R432
PGND
0
PGND
/PSW
/BINT
BATT
SBC
SB1
19 19
33A
IFADCN
15 15 15
21 21 21
9 9 9
F701
CN710
0.25A POW 26
19 OPT6 OPT6 25
OPT6
TXI 24
18 TXI
L706
C701 RXEI 23
RXEI
0.1u RXEO 22
RXEO
R718 100k
R719 100k
R720 100k
R721 100k
R722 100k
R724 100k
R726 100k
TXO 21
26P_TD
TXO
RXD2
18
17
16
15
14
13
OPT2 20
OPT2
A0
P16
P13
P15
P17
P14
OPT7 19
21 R730 OPT7
26P_RD OPT11 18
15 19 12 470 OPT11
I2CCK SCL P12 26P_TD OPT8 17
20 11 OPT8
I2SDA SDA P11 OPT11
21 IC701 10 DTI 16
VCC P10 DTI
R717
9 OPT9 15
100k
I/O CONTROL OPT9

GND
22 8 5V 14
INT P07 OPT8
9 23 7 C703
A1 P06 OPT7 AGND 13
R420
24
0
A2 A 4.7u AO 12
AO
P00
P01
P02
P03
P04
P05
A AI 11
/OINT
AI
1
6
5
2
AGND 10
OPT6 L701 A AGND 9
OPT5 23
18 A
OPT4 OPT5 8
OPT5
OPT3
OPT10 7
OPT2 OPT10
OPT1 OPT4 6
OPT4
19 10
NC 5
R731
R723
R728
R729
R732
R727
CN709
1M
1M
1M
1M
1M
1M
26P_TD 4
15 26P_TD
26P_RD 3
21 A 26P_RD
OPT3 2
OPT3
OPT1 1
OPT1
23 23
IFADCN
18
9
X53-426 9/10
AT AU AV AW AX

CONTROL UNIT (X53-4260-XX) Note : The components marked with a dot ( ● ) are parts of layer 1.
DC SW DC SW
POWER SUPPLY
CN402 7.49V
Q414 Q415
+B EMD12 EMD12
R493
BATT INT A A
7.49V
0
6.05V
DC SW IC414
1
XC61CC5602NR CN404
D408 Q408
VIN
R511 1k
VoUT
LED_G 1
DC/DC EMD12 RESET LED_G
CONVERTER R512 100 /EMG 2
C442
470p
CONTROL A /EMG
SB1 R513 1k LED_R 3
VSS
LED_R
NC
R514 1k IFC 4
R466 IFC
4
10k R515 1k /SAVE 5
R464
470k
/SAVE
A R516 100 I2CCK 6
R461
D408 I2CCK
10k
1SS301F A 7.46V
R517 1k /5TC 7
/5TC
R518 100 I2CSDA 8
D412 I2CSDA
DC SW Q412,413
1SS301F R519 1k SBC 9
R469 CONTROL DC SW VOLTAGE
R465 7.49V REGULATOR R520 1k /T_R 10
470k T_/R
R481
470k
10k IC416 R521 1k TV2 11

Q413 3.32V TV2
S-812C31BPI-G
A 2SA1955A-F R522 1k ASSIST 12
SCTAMI ASSIST
R523 1k
R473
3.32V TV1 13
3.3k
1
TV1
R492
470k
R524 1k
VIN
NC
Q412 VAGC 14
VoUT
SSM3K15TE(F) C465 VAGC
C431
C433
R525 1k 5RC 15
10u
10u
C448
1000p 5RC
1u
oN/oFF
R526 1k TCXO_MOD 16
VIN2
VSS
TCXO_MOD
3.32V A PGND 17
TX-RX UNIT(X57-7370-10) (A/2)-CN900

A
21 R527 1k RSSI 18
6
5
4
31BU RSSI
1SS388F
D413 Q409 PGND 19

D413
2SA1955A-F C454
RTC BATT R528 1k CV 20
R485
CONTROL D411 C466 CV

10k
DC SW A 1u AGND 21
6800p
R479
1SS416 A NC 22
1k
RTC BATT NC 23
CONTROL 2.98V
+B 24
CN401
Q410 3.24V
SSM3K15TE(F) +B 25
A A +B 26
SBC +B 27
PGND NC 28
15
NC 29
AGND 30
R529 100 A PTT 31

/PTT
33A R486
∗R848 Side_G
R530 100 Side_G 32
10 R480
R531 100 Side_1 33
A A Side_1
27k
5
R532 1k W_/N 34
W_/N
VDD
VIN-
R482
10k
IC410
∗R849 R533 100 SDO1 35
0.01u
C444
MCP6021-E/OT SDO1
R534 100 Side_2 36
IF AMP A A Side_2
0.01u
VoUT
C434
VIN+
VSS
R535 100 /PCS_RF 37

R498
33k
/PCS_RF
R536 1k /DSW 38
1
9
3
2
1.33V C451 DSW

IFADCN C432 0.01u R537 1k APC 39
R499
1.33V
22k
APC
0.01u R538 1k /APCSW 40
/APCSW
A R539 1k VCO_MOD 41
VCO_MOD
15 15 R540 1k THP 42
21 21 THP
R541 100 PLD 43
9 9 PLD
R542 1k RFAGC 44
RFAGC
TX-RX UNIT : OPTION BOARD SECTION (X57-7370-10) (B/2) R543 100 SCK1 45
SCK1
GND 46
CN737 R544 1k S_DET 47
AGND 15 S_DET
26 POW GND 48
POW AGND
25 OPT6 oPT10 NC 49
OPT6 A
TXI OPT10 R545 100 IF_DET 50
24
TXI DGND
23 RXEI
RXEI DGND
RXEO oPT3
22
RXEO
OPT3
21 TXO oPT2
TXO
20 OPT2 OPT2
OPT2 oPT4
19 OPT7
OPT7 OPT4
18 OPT11 oPT1
OPT11
17 OPT8 OPT1
OPT8 oPT5
16 DTI X53-4260-XX R848 R849
DTI OPT5 -10 K 0 NO
15 OPT9 POW
OPT9 -11 K3 NO 0
14 5V POW
5V oPT7
13 AGND
AGND OPT7
NC oPT6
12
OPT6
11 NC oPT11
10 AGND OPT11
TXI
9 DGND
DGND TXI
8 OPT5 oPT8
OPT5
7 OPT10 OPT8
OPT10 RXEI
6 OPT4
OPT4 RXEI
5 NC DTI
4 26P_TD DTI
RXEo
3 26P_RD
RXEO
OPT3 oPT9
2
OPT3
OPT9
1 OPT1 TXo
OPT1
26P RD TXO
5V
5V
26P TD
81
X53-426 10/10, X57-737 (B/2) 1/1
AY AZ BA BB BC

TX-RX UNIT (X57-7370-10) (A/2)
THP
SWITCH UNIT CN900 1

1 LED_G 50C
(X41-3710-10) CN901
LED_G
C904 47p
PTT 1 2 /EMG R928
PTT
PTT GND 2 C905 47p 0
C976
Side_G 3 3 LED_R
47p
S1
Side_G LED_R
SIDE 1 Side_1 4 C906 47p
Side_1 TX/RX LED
Side_2 5 4 IFC TX/RX LED
Side_2 IFC SWITCH
C907 47p 1 R : 100mV LG
C913 47p
C943 47p
C945 47p
C946 47p
SIDE 2
5 /SAVE Q900 T : 6.38mV
/SAVE LED_G UMG9N D900
C908 47p R900 B30-2278-05
C901
6 I2CCK 390
I2CCK 470p R902
7 /5TC R903
/5TC C944 10
C910 47p 820
8 I2CSDA 470p
I2CSDA R : 6.57V LR
LED_R T : 79mV
9 SBC
SBC
C912 47p +B
10 /T_R
/T_R
C914 47p
5RC
11 TV2
TV2
C915 47p VOLTAGE
R : 7.49V IC902 REGULATOR(50C)
12 ASSIST T : 7.26V TK11250CUCB
C916 47p 4 3 R927
13 TV1 VIN CoNT /SAVE
1000p
1k
C955
C957
TV1
5 2
1u
C917 47p GND GND
14 VAGC
VAGC 6 1
C918 47p VoUT NP
1000p
C956
C958
0.22u
C964
15 5RC
1u
C919 47p R : 4.97V
T : 5V
16 TCXO_MOD
TCXO_MOD 4
C920 47P R : 4.97V IC903 R : 3.32V
T : 5V TK71733S T : 3.35V
17 GND R431 0
1 5 33C
VIN VoUT
CONTROL UNIT(X53-4260-XX)-CN404
18 RSSI
1000p
1000p
0.22u
0.22u
C968
C970
C952
C954
RSSI 2
C922 47p GND
3 4
19 GND R432 0 oN/oFF NP/VREF
0.22u
C965
VOLTAGE
20 CV REGULATOR(33C)
CV
C923 47p R929
21 GND SBC
1k
R915
R : 4.35mV
470k
22 NC R430 R : 4.974V T : 4.99V
D902
T : 4.987V
23 NC 0 50T CONTROL Q905
2SA1955A-F 50T
24 +B
1000p
R : 3.27V
C961
C971
C969
470p
1u
T : 62.3mV
25 +B IC900
D902 TC75S51FE(F)
26 +B HSC119 1 5
IN+ VDD Q905
2
C925 R908 50T
27 +B 2 SWITCH
VSS R922
47p 47k
28 NC 3 4 1k
R : 4.974V
C951
0.22u IN- oUT
R920
T : 4.25V
47k
29 NC
C963
30 GND
1u
R921
R : 3.285V
47k
50T CONTROL
31 PTT T : 59.4mV
PTT
C926 47p /5TC
32 Side_G
Side_G 2
C927 47p R : 4.977V R : 0.314V
33 Side_1 T : 5.038V Q902 T : 70mV
Side_1 SSM6L05FU-F
C928 47p 50R
34 W_/N
W_/N
R911
470k
50R R918
C929 47p 5RC
SWITCH
35 SDO1 0.47u 1k
R916
C977
470k
SDO1
C930 47p R : 5.5mV R : 3.28V
T : 4.81V T : 68.5mV
36 Side_2
Side_2
C931 47p
37 /PCS_ RF T : 4.974V Q903
/PCS_RF SSM6L05FU-F
C932 47p 50IF
38 /DSW
R912
/DSW
470k
50IF R919
C933 47p IFC
SWITCH
39 APC 1k
R917
470k
APC
C934 47p
ASSIST
40 /APCSW
/APCSW
C935 47p
41 VCO_MOD
VCO_MOD R : 7.494V R : 7.478V
T : 7.353V Q901 T : 7.338V
C936 47p
SSM6L05FU-F
42 THP
C937 47p
R906
470k
43 PLD SB3 R913

PLD SWITCH
1k
R910
470k
C938 47p 3
R : 5.1mV R : 3.276V
44 RFAGC C939 47p T : 55.4mV T : 3.331V
45 SCK1 R : 14.28V
SCK1
C940 47p T : 14.32V
46 GND Q904
Q904 L901 SSM5H01TU 150C
47 S_DET C941 47p DC/DC
CONVERTER 68u
C966
C973
C972
R925
C974
330k
22p
SWITCH
1u
1u
1u
48 GND R901
0
49 NC
50 IF_DET
IF_DET
R905
33
C942 IC901
R : 7.23V XC9101D09AKR
47p T : 7.06V 1 8
EXT VSS
R909 2 7
R904 LSEN VoUT/FB
0 R907 0 3 6
R926
VIN CC/GAIN
22k
S
10 4 5
C953 R914
150k
CN902
C902
C947
CE/SS CLK
470p
470p
4
4.7u16
C950
C948
C949
C962
R923
C967
470p
180p
1u
1u
12k
DC/DC
0.1u
F900 L900 CONVERTER

1SR154-400
2.5A
1000p
C900
C903
470p
D901
REVERSE 4
PROTECTION
82
X57-737 (A/2) 1/4
BD BE BF BG BH

TX-RX UNIT (X57-7370-10) (A/2)
THP THP
50T
1 /T R
50C
R521
10
C558
470p
C543
L513
18n
R : 4.94V
R550
150k
3p T : 4.98V
R : 1.1V
C525 L504 C553 T : 1.27V
47p 12n 10p R : 0.79V C588 TX
T : 0.81V
C550
C537
5p
5p
Q505 10p
2SC5636
C559
R549
470p
270
BUFFER AMP
50C
+B +B
33C
R514
IC500
10
TEMP SENSOR
LM73CIMKX-0
4 3 R572 C514
I2CCK SMBCLK VDD
5 2
0.01u
0.01u
10
C512
C504
ALERT GND C515 0.01u

6 1 IC502
I2CSDA SMBDAT ADDR 0.01u
PLL IC
12
11
10
9
8
7
R570
R503 0
VCC SOC
OSC
NC
GND OSC
/OSC AC GND
OSCout
6
0.01u
10
C508
C505
CPout1
100p
VC VCC 13 5 R522
R505
LD/PS2 VCCcp1
C501
100p
L599 14 4 10
L500 VCC cp2 LD/PS1
15 C521 C526
GND oUTPUT CPout2 3
4.7u 16 /Fin
C513
100p
C506
C509
/Fvco 2 100p 0.1u

10p
10p
X500
VCC digital
17 Fin C527
33C 19.2MHz Fvco
Max out
18 1 R519
Mod in
VCCcp2 VCC 100p
Clock
GND
Data
10
/CS
R523
1k
TCXO MOD R502 C522
21
20
19
23
25
22
24
120k L598 0.1u
R574
IC501
0
LMC7101BIM5 C523
C528
DC AMP for
100p
TCXO MOD
0.01u
100p
C516
1 OUTPUT 5
R506
R567
4.7k
V-
47k
2 R504 C511
V+ 3
100k 10u
C503
R500
3 4
100k
0.1u
R511 10 C517 100p

INPUT+ INPUT- SDO1
50T R512 10 C518 100p
TCXO_MOD
/PCS_RF
R501
C500
C502
470p
100k
0.1u
R513 10 C519 100p

SCK1
PLD
19.2M
2
CV
BUFFER AMP R : 4.15V

L522 R560
D506,510,514,515 T : 18mV
C577
470p
CN500 220n C573 22
R529
FREQUENCY CONTROL
RX VCO
1k
CV Q512
Q504 L508 D510 L521 5p
R544 C556 R575 C566 C581 BUFFER AMP
2SK879-F (Y)
1SV282-F 1SV282-F
C533
470p
0 220n 470p 0 56p 22n 0.5p

C575
R537 1SV282-F
5p
D514
R : 1.11V R : 0.96V
220n
L525
C547
100p
T : 18mV T : 0.43V
220n
L514
1k
C568
0.5p
R530
220n
L518
1SV325F
C571
47k
Q508
4p
D506
R : 4V
2SK508NV(K52) T : 4.03V
R541
220n
L516
10k
D515
R531
C534
VCO
100p
R559
68k
180
OSCILLATION R564 C586

50R
150k 7p
R527 R532 R538 L503
L524 L527
0 0 390 R : 2.5mV
T : 4.2V Q512
C580
R535 10u20
470p
220n
C539
TX VCO
+
C576
2SC5636
0.047u35
0.15u35
L528
27n
C541
5p
C535
R545 L509 C557 R576 D511 C565 L520 C583

150
0 220n 470p 0 27p 18n 0.5p

1SV282-F 1SV282-F
1SV282-F
0.75p
C570
50IF R : 2.5mV
C579
D516
C587
R565
470p
C548
220n
100p
L526
100
4p
C567
T : 1.01V
0.5p
L517 220n
L515
R536
1SV325F
C574
R542
220n
L519
Q509
2p
0
D507
0
2SK508NV(K52)
C585
470p
1SV278F
220n
D519
D517
R561
VCO
180
R543 OSCILLATION R : 1mV

T : 4.17V
4700p
0
C546
D507,511,516,517 D519 Q511

FREQUENCY CONTROL TX R : 4.27V Q510 2SJ347F
MODULATION T : 4.28V SSM6L05FU-F
R : 4.26V
T : 6.94mV
R599
100k
C584 470p
R558
R554
D501,Q503 D505
47k
R563
DC AMP for VCO TUNE

47k
RIPPLE DA221 D505 C562 R552 470k

C582
470p
1u 270k Q510,511
FILTER BYPASS
T/R
DIODE
C536
IC503
R555
SWITCH
47p
C578
R : 14.34V R : 13.73V
L523
47k
4.7u
LMC7101BIM5 OP AMP R568

T : 14.43V T : 13.82V (VCO MOD/APC) R : 4.978V R : 3.25V
R : 1.4V 470k
1 OUTPUT 5 T : 5.06V T : 9.7mV
Q503 V- T : 4.38V
R539
R533
180k
IC504
R562
150C 2SC5383-T111 R : 0.15mV

2 V+
1k
TC75W51FUF Q507 T : 1.84mV

10M
1 8 2SC5383-T111
HSC119
R566
R515
D501
3 4 VDD
4.7k
7
HSC119
R547 C554
C524
100p
47p
R557
INPUT+ INPUT- RIPPLE FILTER

D518
470k
1.5k
R601
C542
R534
18k
0.1u
2
47k
R546
100k
C520
R670 R : 0.14mV
R : 14.33V 3 6
1u
T : 4.08V
T : 14.41V
0
4 5 220k RIPPLE
C529
C572
VSS
100p
R602
10u
120k
FILTER
R548
100k
C600
R520
0.1u
R603
2.2k
1k
R600
1k
C555
APC
1u
C602
0.1u
C601
100p
VCO_MOD
ASSIST
APC
3 3
50R
50IF
4 4
150C
X57-737 (A/2) 2/4

BI BJ BK BL BM

TX-RX UNIT (X57-7370-10) (A/2)
TH600 CN600
THP
50T 100k
C637
470p
-t
RF AMP
Q602
R : 5mV 2SK3077F C621 R628 R620 C670 L605 TX
RF AMP
T : 0.64V
R : 4.75V R : 2.5mV 15p 0 0 470p 6.8n
R626
L603
Q601
15n
120
BUFFER AMP T : 4.8V LOCAL SWITCH T : 2.37V
C623
R : 1.81V 2SC5636 C613 C671 C615
15p
T : 1.89V Q600 C607 R609 D601 7p 7p 470p
R617
L602
18n
330
2SC5636
C691
C618
470p
L604
0.1u
TX C603
L615
7p 0 HSC277
15n
R607
2.2k
R : 1.48V L600
22n
R622
100
10p T : 1.36V
R610
R605
4.7k
10k
C611
R624
C610
C690
R616
R612
470p
470p
0.1u
4.7k
180
H : 4.65V 47k R627
L : 4.64V
C689
C605
R604
470p
0.1u
6.8k
R606
C604
470p
0
330
R623
C614
470p
H : 0.62V
10k
D600 L : 0.42V
R618
50C R608
22
LOCAL
47 SWITCH
50T
+B
HSC277
C619
C612
C617
470p
470p
D600
0.1u
33C
APC PROTECT +B
R635 R658
560 C672 1.8k
HZU5CLL
R654 R655 R659
R : 63mV
6.8u10
D605
C631
470p
+
T : 128mV 270k 10k 470k
R : 3.274V D608 R669
T : 11.2mV R : 0.65V C641 IC600
T : 140mV Q604 HSC119 470 TA75W01FUF
R629 10p
R651
270k
2SC5383-T111 1 8
27k
oUT1 VCC
APC SWITCH R648 2 7 Q610
IN1- oUT-B EMD5
R : 61mV 3 6
HZU2ALL
150k
C640
C622
IN1+ IN2-
470p
47p
R645
R642
R647
T : 110mV
D604
0.39
0.39
0.39
C626
APC SWITCH
0.1u
4 5
VEE IN2+
C653
470p
R633
100
R649
150k AUTO POWER
C636
R653 R652
470p
270k 270k
CONTROL
R660
47k
APC
R656
R664
R641
56k
10k
SWITCH
0
R : 7.11V
T : 1.52V
Q608
APC SWITCH Q607
C651
2SK1824-A
470p
R : 3.294V R657
DTC144EE
/DSW
T : 40mV Q605 R : 13mV 0 APC

SSM3K15TE(F) T : 3.71V APC SWITCH
SWITCH
R : 18mV
3 /APCSW T : 3.92V R : 1.59V
T : 1.52V
R661
100k
1st LO
19.2M
50R
R : 4.849V
R701
560
L701 T : 5mV
L705
560n
C708
R : 0.731V
T : 3.6mV 100p
C732
R728
470p
220
C701
0.01u
R702 C706 L703 C704 C715
R571 330k 10p 47n 47p 0.01u

C700 0
0.01u
C733
C712
C707
100n
L780
L704
1.8u
68p
68p
7p Q700
2SC5108(Y)F
FM IC
2nd LOCAL IC701 R : 4.694V

BUFFER AMP TK10931VTL-G T : 5mV
R : 2.66V
T : -0.8V R : 0.697V
1 24 C730 R733 XF700
CF700 oSC(B) RFINPUT T : 3.6mV
58.05MHz
450kHz 2 0.01u 560k
oSC(E) 23
C790 GND C734 R737 OUT IN C740 R739 RX
OUT IN 3
MIXoUTPUT 22 IF AMP
0.1u CoMPoUTPUT Q701 0.01u 220 0.01u 220
21 R724 100k
R703 4 CoMPINPUT 2SC4215-F(Y)
R730
C739
VCC 20
C737
6p
0
10 NoISEAMPoUTPUT C728 0.1u CN701

2p
C718 5
C738
C703
22p
0.1u
C709 AMIFINPUT 19 R719 VAGC

0.1u 0.1u 6 NoISEAMPINPUT R731
AMIFDECoUPLING 18 270k
R710 C721 7 AMAGCINPUT 10k
C710 FMIFINPUT 17 C760 0.1u
0.1u 0 0.1u 8 AGCAMPoUTPUT
FMIFDECoUPLING1 R721 10k
16
C711 9 RFAGCoUTPUT
FMIFDECoUPLING2 R722 4.7k
0.1u C720 15
10 RSSIoUTPUT
LIMoUTPUT
10p 14 C759 0.1u
R709 11 AMSW
QUADINPUT
10k 12 13 R725 22k
FMDEToUTPUT AMDEToUTPUT
0.47u
C729
CN700
RSSI
0.01u
C713
C719
C725
C724
0.1u
10u
10u
R726 OP AMP
R714 (RSSI/VAGC)
18k
10 IC404
C723
0.1u
R795 TC75W51FUF
R712
R : 2.03V
10k
5
10k 5 4
T : 85mV IN+B VSS
VDD
VIN-
6 3
R704
IN-B IN+A
1k
C722
R792
R797
7 2
100k
47p
47k
oUTB IN-A
0.01u
C717
C735
R736
100k
R717
47p
1 VoUT
47k
VIN+
VSS
8 1
CF701 VDD oUTA
0.01u
C736
450kHz
R735
3
100
2
R738
2.7k
R705 R796 C727 OUT IN C792 R727

0 0 0.1u 0.1u 2.2k R794
IC700
R720
R798
R718
2.2k
R : 1.81V
18k
10k
47
MCP6021-E/OT T : -100mV
BUFFER
IF_DET
50R
VAGC
RSSI
50IF
4 4
150C 150C
X57-737 (A/2) 3/4

BN BO BP BQ BR

TX-RX UNIT (X57-7370-10) (A/2) Note : The components marked with a dot ( ● ) are parts of layer 1. 1
RF FINAL AMP R : 0.5mV ANTENNA SWITCH

T : 1.615V
Q606 Strip line D606 L612 L613 L614
R : 12mV RD07MVS1BT122 R663 C660 HVC131 C663 4T 4T 4T
RF DRIVE AMP
T : 2.34V ANT
Q603 C634 0 100p 100p C665 C667
470p D607
R : 14mV RD01MUS1-T113 R650
R667
82k
C650
C975
C652
C647
C654
L609
7.5p
7.5p
T : 2.81V 2p 1.5p
47p
18p
12p
7T
0 HVC131
C662
C639
R636
R644
L606
220
18n
39p
1p
C666
C668
C669
C664
TX
47
H : 2.33V
4p
4p
8p
5p
L611
220n
L : 1.626V
C627
H : 2.8V
R631
10p
47
L : 1.96V C629
470p
L607
0.01u
C645
C648
C642
150p
L610
0.1u
C635
R639
R646
470p
10k
33k
C625
R630
470p
R666
R665
R632
33k
C661
470p
270
270
10k
R634
0.01u
C643
C646
C649
150p
1u
0
C630
C628
C632
470p
10p
1u
2
50T
+B
L723
4T
R : -35mV ANTENNA SWITCH
T : 0.808V
L709 L710
L725 C809
R : 4.94V
18n 18n
T : 3.8mV 8.2n 18p 3
R742 C749 C753
HVC131
HVC131
D711
C810
C803
D709
4p
2p
4.7k 2p 2p
L716
C741
C751
0.01u
C755
C742
C744
C747
C754
470p
L706
4.7u
10p
10p
4p
3p
R768 R772
0 0
0.01u
C779
C783
C788
C789
C777
C784
R775
470p
470p
470p
100k
0.1u
R : 4.94V
1u
C752
470p
CN702
R746
R748
100k
100k
T : 4mV
BPF
R : 4.89V
R : 4.53V
R745
220n
T : 47mV
L717
R778
100k
1k
T : 47mV D702-704
C756
L711
R : 3.14V
22n
9p
L708 T : 46mV VARI-CAP TUNE R : 4.54V RF AMP

Q703
3SK318 T : 46mV
1st LO 560n Q705
R750 R752 C758 R753 C768 C773 R765 C778 R770 R : 1.99V
270n
L707
3SK318 T : 45mV
0 0 470p 0 1p 1p 0 470p 68
R : 2.96V
C770
C776
C772
C767
C764
C774
L713
L715
L714
8.2n
8.2n
8.2n
R740 R743
1.5p
R : 1.29V MIXER T : 46mV R : 0.87V

4p
9p
9p
9p
3p
T : 43mV T : 42.7mV
47 680
R779
50R
C786
470p
68k
R749
R747
4
150k
180k
1SV286F
1SV286F
1SV286F
D703
D702
D704
0.01u
C743
C746
C745
470p
C782
R771
0.5p
C785
470p
9p
180
0.01u
C750
C748
R744
470p
220
R760
R759
R757
100k
100k
100k
C771
C765
C775
470p
470p
470p
D706,708,710
C800 VARI-CAP TUNE
R799 L720 C795 2p C807 C811 R791
RX 0 10n 470p 5p 9p 0
C850 L726
C804
33n
9p
R : 6.71V
C796
C798
L721
8.2n
1.5p
9P
T : 13.6V
R : 6.71V
1SV286F 100p
C802
T : 13.6V
L722
8.2n
5
4p
1SV286F
1SV286F
D706
D708
RF AGC
R790
D710
100k
R : 137mV
Q706 T : 43mV
2SK1830F
R788
R785
100k
100k
R784
R786
C849
470p
R : 3.8mV
T : 42mV 470k
C801
0
C794
470p
470p
HSC119
R783
D705
220k
R781
1.8k
RF AGC
R761
100
R780
0
C791
470p
6
C769
R762
470p
10k
DC AMP for BPF DC AMP for BPF

R : 13.65V R777
T : 13.72V
10k
C799
470p
IC702 IC703
RIPPLE LMC7101BIM5 LMC7101BIM5
R : 14.28V FILTER
T : 14.32V 1 5 1 5
Q704 OUTPUT V- OUTPUT V-
R763
R773
820k
820k
2SC5383-T111 2 2
V+ V+
HSC119
C780
C766
0.1u
0.1u
D700
R755
3 4 3 4
4.7k
INPUT+ INPUT- INPUT+ INPUT-

R764
R774
100k
100k
R758
R769
R : 14.26V
10k
10k
RIPPLE T : 14.3V
FILTER
C761
R : 0.308V R : 69.8mV
1u
T : 1.63V T : 1.633V
TV1
TV2
4
150C 7
85
X57-737 (A/2) 4/4
86
LCD ASSY
NX-300
20
V5
V4
V3
V2
V1
D7
D6
D5
D4
D3
D2
D1
D0
AO
VDD
VSS
VDD
/WR
/CS
/RES
CN1
CN403
1
5A TXo 33A
CN737
CN710
VOL_GND
1
RXEo OPT1 OPT1 VOL
POWER SW/
SToN
OPT3 OPT3
AF VOL
26P_RD 26P_RD EN3

26P_TD 26P_TD
DI RXEI NC NC AGND
OPT4 OPT4
OPT10 OPT10 EN4
OPT5 OPT5
TXI
DGND AGND EN1
TCNT
AGND AGND
AI AI EN2
C3 AO AO
CHANNEL
X57-737 B/2
MDWN
AGND AGND +B
5V 5V
SELECTOR
OPT9 OPT9 SB1

INH SB2 DTI DTI
OPT8 OPT8 10
OPT11 OPT11
OPT7 OPT7
oPT1 OPT2 OPT2
OPTION PCB
oPT5
TXO TXO
RXEO RXEO
RXEI RXEI
oPT2 TXI TXI
oPT4
OPT6 OPT6
POW POW
26
CN23
oPT3 DGND
AGND AGND
AGND 14
6_/KEYI0
13
BL_SB
12
6_/KEYO1
11
X53-426
6_/KEYO0
10
6KEY/SP/MIC
BL_SB
9
14
NC 6_/KEYO2
CONTROL PCB
8
RXD
6_/KEYI1
TXD 7
5V
E SP-
CN405
6
OPT
PF SP-
5
PTT
ME SP+
4
EMC
INTERCONNECTION DIAGRAM
MSW SP+ 3
SP-
SP+ EMC
2
SSW
1 ME
1
X41-372
UNIVERSAL CONNECTOR
SWITCH UNIT
CN701
20
NX-300
INTERCONNECTION DIAGRAM
CORD ASSY
CN404 1
X42-334 1 CN900
LED_G LED_G ANT
/EMG /EMG
LED_R LED_R
IFC IFC
/SAVE /SAVE
I2CCK I2CCK
/5TC /5TC
I2CSDA I2CSDA
SBC SBC
/T_R /T_R
TV2 TV2
ASSIST ASSIST SWITCH UNIT
TV1 TV1
VAGC
5RC
VAGC
5RC
X41-371
TCXO_MOD TCXO_MOD
PGND GND CN901
RSSI RSSI
PGND GND
PTT
CV
AGND
CV
GND
TX-RX PCB PTT
GND
NC NC
NC
+B
NC
+B
X57-737 A/2 Side_G
Side_1
+B +B
Side_1
+B +B
+B +B Side_2
Side_2
NC NC
NC NC
AGND GND
PTT PTT
Side_G Side_G
Side_1 Side_1
W/N W/N
SDO1 SDO1
Side_2 Side_2
/PCS_RF /PCS_RF
/DSW /DSW
APC APC
/APCSW /APCSW
+
VCO_MOD VCO_MOD
BATT
THP THP
PLD PLD
RFAGC RFAGC
-
SCK1 SCK1
GND GND
S_DET S_DET
S
GND GND
NC NC
IF_DET IF_DET
50 50
87
NX-300
BLOCK DIAGRAM
X53-4260-XX (Control unit) X102
SM5023CNDH-G 18.432MHz
IC107 VC
33M
TCXO
BSHIFT
33A 15M 33M
IC101 IC103
Flash
ROM
SRAM DSP IC102
/DRST,DCLK,/SYMTIM,
/RSSITIM,/DINT,
/SWUP,FSDET,/HINT
MCD1AF,/MCSCKAF,/MCCSAF,MCD0AF,
IC401 TC7MZ245FK
IC402 TC7WZ245FK-F
BUS SW MCD1CN,/MCCXCN,/MCD0CN,/
MCCSRCN,MCSCKCN
CN1 to LCD Module
D0~15,A0~20,/RD,/WR,/CS0,/CS2,/CS3,/CS4/HDS2,/HRDY
/LCDRST
TXD0
RXD0
IC703 RTS0
33M
M62364FP-F(7/8) CTS0
LCDCNT DSR
DAC /PTT
IC403 IC105
LMC7101BIM5 /UDET XC6109C29ANN
RXD3
N100C IC410
ENC1 RESET 33M
ENC2 MCP6021-E/OT
ENC3
IF_DET
ENC4
/BINT
/PSW
IC711 Q704
Q101 2SA1832(G,R)F TC75W51FK(F)(2/2) 2SC4617(S)
Q102 2SC4617(S) ASQAPC
Q103 SSM3K15TE(F) ASQDET BPF AMP
SB2 5A VOX
IC702 IC702
12key Back Light VOL
TC75W51FK(F)(1/2) TC75W51FK(F)(2/2)
BATT
D3,D4
D7,D8
AVR PFKEY
LPF LPF
BLC
SB2 5A BLC
LCD Back Light
D1,2,5,6
MM ASIC
SCSW
D9,10 AVR /AMT IC108
BLC STSW
Q1 2SA1362(GR)-F /SCSW
EXAMT
Q2 2SC4617(S) INAMT AMT
Q3 SSM3K15TE(F) BEEP IC704
BL_SB
TONESW TC75S51FE(F)
/MNDNU RXAF
5UC LPF
Q415
EMD12 LED-G IC707
DC SW TC7W53FK(F)
Q414 SBC
CN404 50pin Board to Board
EMD12 LED-R
DC SW
33A Q702
SSM3K15TE
+B
SBC TONE
IC703 SW
TV1 M62364FP-F
DAC SDO0,SCK0
TV2 (3/8,4/8) /EVCS
TONESW
RSSI , THP , VAGC , CV , S-DET
IC706 IC710
/EMG , /PTT , Side_1 , Side_2,Side_G , IFC , TC75S51FE(F) TC75W51FK(F)(1/2)
5RC , 5TC , /DSW , /APCSW,SBC , /T_R , MIC
ASSIST , SDO1 , SCK1 , PLD LPF SUM
/RINT
CN701 (for production)
32K
DTI from ANI
TO DSP I2CCK,I2CSDA
IC403 IC705 IC705

RV5C386A
RTC TC75W51FK(F)(2/2) TC75W51FK(F)(1/2)
I/O Expander /OINT MOD
LPF LPF
IC701
X101 32.768kHz
OPT1,2,3,4,5,6,7,8,11
/KEYI 0,1,2,3,4
KEYO 0,1,2,3
26P_RD
26P_TD
OPT10
RXEO
OPT9
RXEI
POW
TXO
DTI
TXI
AO
5A
AI
KEY Matrix
(12key)
CN710 26pin Option Board
88
NX-300
BLOCK DIAGRAM
IC404 L401 , D406 , D405
XC6204B332M IC407 LT1616ES6-PBF
DCDC
33M AVR +B
Converter
SBC
IC405 Q402 SSM6N16FE-F D408
XC6205B152PRN 1SS301F
15M AVR /PSW DCSW

Q408 IC414
Q401 SSM6N16FE-F SB1 EMD12 XC61CC5602NR
IC406
XC6204B332M
/BINT RESET
IC416
33A AVR S-812C31BPI-G
SCTAM1 DCSW AVR

Q413 2SA1955A-F
Q412 SSM3K15TE(F)
31BU DCSW
D412
Li Battery
CN401
1SS301F
SBC
Q409 2SA1955A-F Q403 2SA1955A-F

Q410 SSM3K15TE(F) Q404 SSM3K15TE(F)
CN403
SB2 DCSW
+B
SB1
BATT
33A
IC708 XC6204B502PR
VOL Volume
5A AVR
N100C
-10V DCDC
IC403 LM2682MMX ENC1
ENC2 Selector
50U AVR ENC3
ENC4
knob
D705 IC711 IC411
5UC
RB706F-40 TC75W51FK(F)(1/2) NJM2880U105ZB
Rect AMP ASQDET

CN23
+B Q406 2SB1132(Q,R) 6_KEYO2

Q407 UMG3N 6_KEYO1 KEY
APC 6_KEYO0 Matrix
AVR 6_KEYI0 (6key)
IC703 Q405 6_KEYI1
M62364FP-F(8/8) SSM6N16FE-F
INAMT 6key
DAC DO BL_SB
EXAMT Back Light
Q701 2SA1832(GR)F IC413
INAMT TPA6201A1DRBR
MUTE OPT10
IC409
IC713 IC703 IC703 IC408 TC75W66FK-F
TC75W51FK(F)(2/2) M62364FP-F(6/8) M62364FP-F(5/8) TC75S51FE(F)
SUM DAC DAC AMP IC412

TPA6201A1DRBR
BEEP
STSW
EXAMT CN405
IC715
OPT9 VOX AMP TC75S51FE(F)
AI from VGS MUTE EMC
MSW MSW
IC714
/UDET SSW
IC709 TC7W53FK(F) D706
TC7W53FK(F)
Rect RB706F-40
/PTT PTT
OPT6 PFKEY PFKEY
AO to VGS RXD3 OPT
50U 5V
VOX IC716
TXD
AMP TC75W51FK(F)(2/2)
RXD
IC712 IC716 Q707 Q4 SSM3K15TE(F)
NC
TC7S66FUF TC75W51FK(F)(1/2) 2SJ243-A Q5 2SJ347F
MUTE AMP MUTE MUTE

TC7WH126FK(2/2)
AI from VGS
TC7SET08FU-F
/SCSW MM MSW
TC7WT125FUF
AGC
IC417
SSM6N16FE-F
IC415
IC418
D703,704 RB706F-40
Q411
Q705 2SC4738(GR)F
Q706 2SA1832(GR)F
TCXO_MOD
IC710 IC703 IC703

RXD0
BER_CLK
SCRXD
BER_EN
TXD0
SCTXD
RTS0
BER_DATA
TC75W51FK(F)(2/2) M62364FP-F(1/8) M62364FP-F(2/8)
SUM DAC DAC VCO_MOD
DI
89
NX-300
BLOCK DIAGRAM
X57-7370-10 (TX-RX unit)
CN900
Q507
I2CCK 2SC5383-T111
I2CSDA Ripple
50C
Filter
IC500 Q510 SSM6L05FU T/R
/T_R
LM73CIMKX-0 Q511 2SJ347F SW
Temp. Q600
33C
Sensor IC502 2SC5636
TCXO_MOD VCVC Loop BUFF BUFF

VCO
TCXO Filter AMP AMP
IC501 X500 19.2MHz
LMC7101BIM5 PLL Q504 Q512
2SK879(Y)F 2SC5636
/PCS RF
SDO1 Q508,509 2SK508NV(K52)
SCK1
50C
CV
D506,507 1SV325F
IC504 D519 1SV278-F BUFF
TC75W51FUF(1/2) D506,507,508,509 AMP
PLD D514,515,516,517 50C
VCO MOD
RX : 391.95~461.95MHz
1SV282-F*4
TX : 450.00~520.00MHz
Q505
150C 2SC5636
Q503
+B
Q901 2SC5383-T111
Ripple
SSM6L05FU IC503
Filter
DC SW SB3 LMC7101BIM5
ASSIST
SBC
Q904 SSM5H01TU LPF

IC901 XC9101D09AKR
DCDC Q700 2SC5108(Y)F
150C
Converter
IC902 x3
TK11250CUCB CF700 450kHz
AVR 50C
50R BPF
/SAVE IC700 CF701 Q701
MCP6021-E10T 450kHz 2SC4215-F(Y)
IC903 TK71733S
IF AMP
IF IF
AVR 33C IF_DET BPF IC701
AMP AMP
TK10931VTL-G
Q902 SSM6L05FU
DC SW 50R
50IF
TC75W51FUF(1/2)
TC75W51FUF(2/2)
5RC
Q903 SSM6L05FU
IC404
IC404
DC SW 50IF
RSSI
VAGC
IFC
Q905 2SA1955A-F
DC SW 50T
/EMG SB3
/5TC
D900
IC900 TC75S51FE(F)
S1
RSSI , THP , VAGC , CV , S_DET , IF_DET

UMG9N
DC
Q900
SW
/EMG , LED_R , LED_G , APC ,
/DSW , /APCSW , CV , ASSIST ,
VCO_MOD , TV1 , TV2 , /T_R , LED_R
PTT , Side_1 , Side_2 , Side_G
LED_G
90
NX-300
BLOCK DIAGRAM
TX/RX: 450~520MHz
D606,607
D600,601 Q601 Q602 Q603 Q606 D709,711
HSC277*2 2SC5636 2SK3077F RD01MUS1 RD07MVS1B HVC131*4
Pre- Pre-
T/R Drive Final ANT
Drive Final LPF
SW AMP AMP SW
AMP AMP
5R
5T
5T
5T
5T
Q610
EMD5
Q604
DC SW DC SW /APCSW
2SC5383-T111
IC600
/DSW TA75W01FUF
APC
LPF
+B
150C Q607 Q608
DTC144EE 2SK1824-A
2SC5383-T111
1st Local : 391.95~461.95MHz
ASQ
Q704 DC SW Protect
Ripple Q605 APC
Filter SSM3K15TE IC504
TC75W51FUF(2/2)
/APCSW
IC703
IC702 LMC7101BIM5
TV1
LMC7101BIM5
TV2
1SV286F*2
1SV286F
D702,703,704
D706,708
1SV286F*3
D710
TUNE TUNE TUNE

XF700 Q703 Q204
58.05MHz 3SK318 3SK318
1st RF
MCF BPF BPF Notch
MIXER AMP
L713,714,715 L721,722 L726
50R
+B +
BATT
7.5V
-
CN901
S_DET S
PTT PTT
Side_1 Side1
Side_2
Side2
Side_G
91
92
Receiver Section
RF (Center Frequency) IF1 (58.05MHz) IF2 (450kHz)
-118.5dBm
NX-300
-118.5dBm -119.0dBm -105.0dBm -119.0dBm -103.0dBm (-56.5dBm) (-61.0dBm) (-66.5dBm)

LNA IF Amp
Mixer MCF FM IC CF
C811 C795 C758 Q703 C734 C730 C792 C727 C451 C432
Q705 XF700 Q701 IC701 CF701 IC700 IC410
AF (1kHz)
92.5mVrms 92.8mVrms 92.7mVrms 8.7mVrms 124mVrms 123mVrms

SMF DAC SP Drive Audio Amp
ASIC SCFC To make measurements in the AF section,
500mVrms
connect the AC level meter.
C709 C756 C424 C438 (ANT input : -53dB,1kHz FM, 3kHz DEV (Wide))
IC108 IC704 IC707 IC713 IC703 IC408 IC409 IC413
In the RF section, use a 1000pF coupling
capacitor.
(The display shows the SSG input value
required to obtain 12dB SINAD without
Transmitter Section local level.)
AF (1kHz)
391.8mVrms(W) 412mVrms(W) 352mVrms(W) 348mVrms(W) 27.6mVrms(W)

64mVrms 125.9mVrms
LEVEL DIAGRAM
IC102 195.9mVrms(N) 206mVrms(N) 176mVrms(N) 174mVrms(N) 13.8mVrms(N)

(at MIC terminal)
47.4mVrms 69.8mVrms 410mVrms(W) 352mVrms(W) 348mVrms(W)
DSP 205mVrms(N) 176mVrms(N) 174mVrms(N)
ASIC VCO
C790 C762 C721 2PIN-4PIN C555 C562
IC716 IC710 IC706 IC108 IC705 IC710 IC703 IC703 IC504
RF (Center Frequency)
AG is set to the MIC input becomes (3kHz/1.5kHz) at 1kHz

2.6dBm 7.9dBm 5.0W
MOD (Wide/Narrow).
13.0dBm 22.6dBm 33.0dBm
To make measurements in the AF section, connect the
AC level meter.
VCO
C586 C603 C607 D601 C613 C670 C634 C660 In the RF section, use a 1000pF coupling capacitor.
Q600 Q601 Q602 Q603 Q606
D600
C588
RXLO
PLL
NX-300
OPTIONAL ACCESSORIES
KNB-47L (Li-ion BATTERY PACK) KNB-48L (Li-ion BATTERY PACK)
■ External View ■ External View
■ Specifications ■ Specifications
Voltage ................ 7.4V Voltage ................ 7.4V
Battery capacity ... 1950mAh Battery capacity ... 2550mAh
■ Schematic Diagram ■ Schematic Diagram
DISCHARGING TERMINALS DISCHARGING TERMINALS
S S
560kΩ
Thermal switch Thermal switch
(Breaker) (Breaker)
PROTECTION PROTECTION
CIRCUIT CIRCUIT
THERMISTOR THERMISTOR
10kΩ ±0.5% 10kΩ ±0.5%
DIODE DIODE
S T S T
CHARGING TERMINALS CHARGING TERMINALS
93
NX-300
SPECIFICATIONS
GENERAL
Models .............................................................................
K : Basic Model K3 : w / 12-key Model
Frequency Range ............................................................. 450~520 MHz
Number of Channels ........................................................ 512
Zones ...............................................................................
128
Max. Channels per Zone ................................................. 250
Channel Spacing .............................................................. Analog : 12.5/25 kHz Digital : 6.25/12.5 kHz
Operating Voltage ............................................................ 7.5V DC ± 20%
Battery Life (with KNB-48L) ............................................. 5-5-90 duty cycle : more than 12.5 hours
10-10-80 duty cycle : more than 8.5 hours
Operating Temperature Range ........................................ –22°F to +140°F (–30°C to +60°C)
Frequency Stability .......................................................... ± 1.0 ppm
Antenna Impedance ........................................................ 50Ω
Dimensions (W x H x D) (Projections not included)
Radio only ................................................................... 2.28” x 5.02” x 1.63” (58 x 127.5 x 41.3 mm)
with KNB-47L .............................................................. 2.28” x 5.02” x 1.63” (58 x 127.5 x 41.3 mm)
with KNB-48L .............................................................. 2.28” x 5.02” x 1.91” (58 x 127.5 x 48.5 mm)
Weight
Radio only ................................................................... 8.82 oz (250g)
with KNB-47L .............................................................. 13.23 oz (375g)
with KNB-48L .............................................................. 14.29 oz (405g)
RECEIVER
Sensitivity ........................................................................ Digital @6.25kHz (3% BER) : 0.20µV Digital @12.5kHz (3% BER) : 0.25µV
Analog (12dB SINAD) : 0.25µV
Selectivity ........................................................................ Analog @25kHz : 72dB Analog @12.5kHz : 65dB
Intermodulation Distortion ............................................... Analog : 70dB (± 50, 100kHz)
Spurious Response .......................................................... Analog : 70dB
Audio Distortion ............................................................... Less than 3%
Audio Output ................................................................... 500mW / 8Ω
TRANSMITTER
RF Power Output ............................................................. 5W / 1W
Spurious Response .......................................................... 70dB
FM Hum and Noise ......................................................... Analog @25kHz : 45dB Analog @12.5kHz : 40dB
Audio Distortion ............................................................... Less than 3%
Modulation ....................................................................... 16K0F3E, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D,
4K00F7W, 4K00F2D
Analog measurements made per TIA/EIA 603

KENWOOD reserves the right to change specifications without prior notice or obligation.
2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
P.O. BOX 22745, 2201 East Dominguez Street, Long Beach, Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands
CA 90801-5745, U.S.A.
Via G. Sirtori, 7/9 20129 Milano, Italy

6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8
Bolivia, 239-08020 Barcelona, Spain

Rembrücker Str. 15, 63150 Heusenstamm, Germany
(A.C.N. 001 499 074)

Leuvensesteenweg 248 J, 1800 Vilvoorde, Belgium 16 Giffnock Avenue, Centrecourt Estate, North Ryde, N.S.W. 2113 Australia
L’Etoile Paris Nord 2, 50 Allée des Impressionnistes, Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road,
Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex Kwai Fong, N.T., Hong Kong
KENWOOD House, Dwight Road, Watford, Herts., 1 Ang Mo Kio Street 63, Singapore 569110
WD18 9EB United Kingdom
A B C D E F G H I J K L M N O P Q R S
1 NX-300 PC BOARD PC BOARD NX-300 1
CONTROL UNIT (X53-4260-XX) -10: K, -11: K3 CONTROL UNIT (X53-4260-XX) -10: K, -11: K3
2 2
Component side view (J79-0131-19) Component side view (J79-0131-19)
CN22 D3 D4
3 3
C15
D19
D18
Q4
G
S
S13
D
S4
S3
S2
R26
R24
R23
R22
R20
7
1
*
R27 Q5
L2
L1
4 4
G
S
D
C17
C16
R40
R21
R25
C14 C13
14
1
ME
EMC
SP+
SP+
SP–
SP–
6_/KEYI1
6_/KEYO2
BL_SB
6_/KEYO0
6_/KEYO1
BL_SB
6_/KEYI0
AGND
D2 D1 C5
C6
5 D5 5
C4
20 V5
CN23 C3 V4
V3
C8 V2
C2 V1
4 3 VDD
VSS
C1
IC1 VDD
R12
G
Q3
S
D7
D
6 6
CN1
S12
5 1 R10 D6
S7
S6
S5
8
2
0
D5
R9 D4
R2
TH1
D3
C41
R3
R8 D2
R1 R17
C12
R14
R16
R7 D1
D0
D13 R6
D11
R15 /WR
C11 AO
R5 /RES
R29 1 /CS
R4 C40
Q2
D14
Q1
7 C28 7
C7 R11
D15 R18
R483
D6 R30
C23
C26
D10
D12
D9
C10
C24 C27 R406
D16
L3
L7
L5
L4
C452
R34 C29
R32 C34
R31 C38
R28 C25
R19 C36
C31
C30
C33
IC415
5 1
4 3
L6
C32
C35
C37
8 8
D20
D21
D22
R33
R35
R500
S11
S10
S9
S8
6
3
9
#
D17
D23
R853
R849
R848
9 9
CN24
J79-0131-19 D7 D8
10 10
Component side
Ref. No. Address Ref. No. Address Ref. No. Address Layer 1
IC1 6K D4 3Q D14 7M Layer 2
11 IC415 8K D5 5B D15 7L Layer 3 11
Q1 7K D6 7B D16 7L Layer 4
Q2 7L D7 10O D17 9L Layer 5
Q3 6L D8 10Q D18 4L Layer 6
Q4 4L D9 7D D19 4L Foil side
12 12
Q5 4L D10 7C D20 8M
D1 5D D11 7L D21 8M
D2 5C D12 7M D22 8L
D3 3O D13 7M D23 9L
13 13
64 65
14 14
CONTROL UNIT (X53-4260-XX) -10: K, -11: K3 CONTROL UNIT (X53-4260-XX) -10: K, -11: K3
2 2
Foil side view (J79-0131-19) Foil side view (J79-0131-19)
C427
R460
R467
C711
C715
R777
R402
IC704
D704
D409 R735
R766 C725
R472 C410 Q102 Q101 C712
C726
C710
R733
R737
R742
5 4
5 1
4 3
8
5
3 R496 R117 R114 R112 R745 R750 3
C123
C114
C798
L709
C429 R442
Q103
IC409 Q405 IC707
IC104
R118 C111
R116 C112
R115 C107
R113
R111
C470
5 1
4 3
D
L410
C727
C724
5 C115 R106 R793
G
L711
1
S
4 3 C717 C722
C766
R457
8 1
R447
R474 1 8 R829
+
C756
R765
1
C445
C449
6 1 C767 R758 R755
C732
C440
C116
C104
R123
R122
R148
R119
R110
R105
R701
R703
R705
R707
R709
C415 + IC413 IC405 L710 C118 R108 C108 R753 C745
L401 R489 R462 R133 D101 R414 R847
C797
S C731
4 5 R401 R746 C714 D
C413
R800
R453
R458
R455
R459
R415 Q702 G
C795
R846 R842
C437
L712
C704
R770
R769
R725
C416 3 4 R403 D703
19
R738 R802
C122
R120
C709
R804
R471 R132
1
C438 R490 R495 R416 R845 R749 C746
R768 R754
C424 Q407 R140 R405 R713 C761
R484 R407 R144 S R779
5 4
D406
4 R446 4 3 R139 C782 C781 1 8 4

R434
R441 R408 R418 D R712
C779
D410 IC103
CN101
IC105
R497 IC402
3 2
IC709
C720
D405 CN701
R815
C430 G
5
C422
R823
R822
6 1 R443 C402 8 1 R194 R193 C792 R710
C418 4 5
IC713
D401
R836 C790 R832 R830

Q707
1
IC408 R475 1
R797
4 3 8 R147 C120
C447 R837 C793
C450
C777
C439 R818 R807
C417
R424
1 6 11 10 R146 R137 R410 R852 R851 5 4
R844 R843
IC412
4
5 1 C103 C124
R487 B R838 C794 IC714
20
2
IC407 4 5 R145 R149 D402 C778 R814
C420 R433 IC102 C102
R431
R425 8 1
CN102
C435 R834 C796
G
S
S
3 4
C425 R150 R142
CN702
R805
IC401
C Q406
PTT2
R101
D417
D
C436 R488 R494 R411
R711
R715
R714
L704
R716
R136 C121
R702
Q706
R704
R706
R748 C763
Q705
C788 C786
C705
R736
5 L409 C469 5
C414 C411 D403
L402
E C706 R806
C713 R751 R850
C708 C707
R811 R739
R141 R135 C787
CN703
1 8
C401
PTT1
C789 C791
R833 R835
R549 C468
C419 IC101 R468 R412 C772
C101
1 5 C119 IC716 R831 R798
CN103
20 1 C106 F701 5 4
R513
R517
R521
R525
R531
R535
R539
R543
C110 4 5
IC715
1 5 IC702 C755
R820 R825
R790 R785 C760

IC406 L707 R547 5 4 R128 C105 D404
CN704
RSSI
R127 R167 R828 3 4 8 1
R502
3 4 IC417 L717 R840
R839
R511
R515
R519
R523
R529
R533
R537
R541
R544
C135 R413
D414
C785
8 1 IC109 D707 D706 C723 C716
1
R743 C804
Q414
R503 R841 C744 C775
IC711
CN106
DOWN
CN705
MAN
R803
4 3 C453 C464 R546 4 3 C157 R192 R740 R816 R812 C734
49
D102
R427 R747
C117
C113
C109
R131
R129
R126
R143
R121
R107
R103
R102
LED_G
LED_R
/SAVE
/5TC
SBC
TV2
TV1
5RC
GND
GND
GND
NC
+B
+B
NC
PTT
Side_1
SDO1
/PCS_RF
APC
VCO_MOD
PLD
SCK1
S_DET
NC
C759
1
R154 1 8
6 6 1 C156 R190 R813 R771 6
8
R428
R741 C719
+ CN401 – 5 1 IC712 IC710 13 12
Q701
Q415 1 8 R155
CN706
R157 R181 1 5
GND
R778
C801
4 3 R429 4 5
TCXO_MOD
CN404 IC418 L705 C158 R153

R187 R183 CN105 R799
C803
C752
R420
/APCSW
6 1
I2CSDA
3 4
Side_G
IF_DET
RFAGC
ASSIST
Side_2
C750 R794 G
R795
I2CCK
R479
VAGC
/DSW
4 5
/EMG
C154
GND
GND
GND
/T_R
Q703 D C753
W/N
RSSI
THP
R162 C130
IFC
NC
NC
L713
CV
+B
+B
R466 R464 C145 R787 C749 CN707 S

50
2
R159
R156 C148
C762
C802
D415 R752 TXD Q704 C764
R130 CN104 C701
Q408
D413
6 1
4 3
L706
R175 R783
R512 R514
R516 R518
R520 R522
R524 C465
R527 R526
R530 R532
R534 R536
R538 R540
R542
C765
R767
R808
6
R784
R786
D411
IC107
R801
IC703
R809
R810
R756
IC108
R545
X102
C134
R506 C461
R510 C457
R509
R508 C463
R507 C462
R504 C455
R166
C406
C408
R409
L403 + C404 R185 C141 R178 C739 CN708 R732 R717

C721 R759
3
C407 RXD
R528
7 R172 C153 R417 7

C459
R501
R177 IC706
R161
R160
R165 C740
C460
C456 10
C735
C738
R775
R796
D408
24 19
TH701
R827
C768
C799
5 4 R180 C146
C451 R498
Q409 R176 R722 1 18
6 1
4 3
R454 R451 C466 C743
C403
IC403
R465
R461
R469
R485 R432 R174
C771
C151 R721
C758
1
R435 R436
CN712 IC701
R499 C434
R826
C444 R486
G + 1 6 R158 C152 R731
L701
33M
VOL
VOL_GND
EN1
EN4
AGND
EN3
SB1
+B
EN2
8 1
6 1
4 3
R477
R491
R788 C748
5
1
Q410 D
CN711
3 4
1 5
IC410
24 1
R789
R782
R729 6
R824
S 3 4 L8 R168 C757 13
D412
IC106 7 12
Q411 R720
R819
Q401
C454 + C405 14
1
C160 C138 C747 R780 R730
R726
10
C161
C155 R173 R426

R170 R163 C140
R188 C147
R189 R186
R171 R184 R440
R718
25 OPT6
R719 R728
SSW
SP+
SP–
MSW
EMC
ME
PTT
PF
OPT
E
5V
TXD
RXD
NC
CN403
C159
1 OPT1
L708
R470 C428
D705
8 C131 C139 R723 8
C737
R482 R480 C432
26P_RD
NC
OPT10
AGND
AI
AGND
OPT9
OPT8
OPT7
TXO
RXEI
R481
D702
R763
6 1
4
C800
R762
IC416
C443
R463
CN402 C441
C446 R727
R191
R182 R419
+ + C780
R437
Q403
R138
C730
R449
R448
CN709
Q402
3
C142
C133
R444 R791 D701 R821
1 6 CN405
R456
R452
4 3 X101
R439
C448
R493
CN710
1
3 4
C736 R764
R724 C718
C421
G
R445
R450
IC705
C442 D 5
IC411 1 C742
26P_TD
S Q404
D407
Q413 R438
OPT11
AGND
RXEO
3 2
OPT3 2
OPT4
OPT5
OPT2
POW 26
5
8
L102
C467 C412
R548 L702
DTI
TXI
AO
R473
4 3
D416
1 C143 C136 C149
5V
R492 5 IC708
C751
9 4 1 L714 9
C409
IC404 C144 C137 L716 L715 C150 L101 R761
C728
R478
IC414 3
D Q412
4
G
5 1
S
R757 R744
C431
C433
C703
R404
J79-0131-19
10 10
Component side
Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Ref. No. Address Layer 1
IC101 5K IC404 9D IC417 6F IC711 6S Q404 9E Q701 6Q D404 5M D416 9E Layer 2
11 IC102 5I IC405 3F IC418 6F IC712 6N Q405 3E Q702 4R D405 4B D417 5C Layer 3 11
IC103 4K IC406 5C IC701 7Q IC713 4Q Q406 5E Q703 6R D406 4C D701 8R Layer 4
IC104 3H IC407 5B IC702 5R IC714 5R Q407 4E Q704 7R D407 9D D702 8R Layer 5
IC105 4L IC408 4C IC703 7P IC715 5P Q408 7C Q705 5O D408 7C D703 4O Layer 6
IC106 8I IC409 3C IC704 3P IC716 5N Q409 7A Q706 5O D409 3D D704 3O Foil side
12 12
IC107 7I IC410 8E IC705 9N Q101 3K Q410 8A Q707 4N D410 4D D705 8R
IC108 7K IC411 9F IC706 7N Q102 3K Q411 8G D101 3L D411 7A D706 6O
IC109 6G IC412 4D IC707 3P Q103 3L Q412 9D D102 6G D412 8C D707 6O
IC401 5F IC413 3D IC708 9Q Q401 8D Q413 9C D401 4M D413 7A
13 IC402 4F IC414 9A IC709 4R Q402 8C Q414 6C D402 5M D414 6F 13
IC403 7F IC416 8A IC710 6N Q403 8D Q415 6C D403 5M D415 7F
66 67
14 14
TX-RX UNIT (X57-7370-10) (A/2) TX-RX UNIT (X57-7370-10) (A/2)

Component side view (J79-0128-19 A/2) Component side view (J79-0128-19 A/2)
2 2
C533
CN500
C649
R529
C630 C646
S
Q504
CV
C628
R541 R537
C651
R649
R647
R645
R642
C946
Q605
C640 R648
3 3
G
S
D
R652 R651
C969
R530 R531 C534 PTT 1
+
CN901
R653 GND
1
C641
4
L503
R641 Side_G
C945
IC600
C541
R654 Side_1 C971

C943
Q607 Side_2 5
R538
R655 C636 C913 TX-RX UNIT

R566
8
C542 C976
4 R921 4
(X57-7370-10) (B/2)
R920
C963
R656
Q608
1 5
IC900
R661
Q905 R922
C653 R659 S
4
D505
R533 D
R927
L900
TH600
R660
C637
R539
R657 G C964 TXO
Q610
6 1
4 3
5V
C961
C536
R664
S1
1 5 D901
5 R532 R658 RXEO 5
R669
+
1
C550
C543 C537 OPT9

IC503 C672
IC902
R536
R908
C539
D608 +
C956
3 4 L504 F900 D902
C553 RXEI
C958
4
6
R535
R506
DTI
R522
C529
R520
R534
C525
L513
C527
C526
C521
R523 R755 C951

R519
C903
C900
C558
R521
D700
R550
C522
C523
R527 C528 TXI

6 + 6
R554
R555
C631 Q604
Q505
+ C957 OPT8
C600
C524 R633
C761
C535
6 1 R670 D605 Q704 C955

C519
C518
R513
7 25 R552 C626
C554
C559 C514 R906 OPT6
C572
IC502
C562 1 8 OPT11
D604
Q901
C512
R515
R549 R635
R512
R567
C602
C517
R511
R546 R547 IC504
R603
R764
Q503 R514
D S
G G
S D
12 19 R910 POW
R548
7 7
C977
R602
R601
4 5 Q902
4
13 18 C766 OPT7
IC702
D501 C515
Q507
C516 C513
S D R913
C511
R504
R763
C555
R557
R911
C520
R916
R758
3
D518
L598 L599 R600 R629 C622 G G
R918
C601
R905
OPT1
D S R902
C948 R907 R909 OPT5
R712 R704
R574
C908
5
4
IC501
C940
C928
C936
C932
C925
C917
C912
R431
C717 R705
C503
OPT2
R502
R724 S
R720
R718
R796
8 C950 + OPT4 8
D900
1
C728 R798
C941
C938
C934
C930
C926
C919
C915
C910
C906
C904
R432
R500 L901
3
1
IC700
C508
C505
CF701
R503 1 24 C727 C949 DGND
C502
C500
R501
C902
R714
OPT3
R904
4
5
R572
49 NC
R717
C723
R914
C947
C501
R900
R903
S_DET
SCK1
PLD
VCO_MOD
APC
/PCS_RF
SDO1
Side_1
PTT
NC
+B
+B
NC
GND
GND
GND
5RC
TV1
TV2
SBC
/5TC
/SAVE
LED_R
LED_G
R570 AGND
CN700
R736
RSSI
C504 1 5
C792
R719
OPT10
9 R505 9
C709
C953
R738
1
Q904
R794
IC701
C509
X500
J79-0128-19 B/2
TCXO_MOD
CN900
C
3 4
Q900
IC901
C735 C736 R735
C759
R722
R727
/APCSW
3
I2CSDA
Side_G
IC500
IF_DET 50
RFAGC
ASSIST
Side_2
C710
B
E
I2CCK
VAGC
/DSW
/EMG 2
GND
GND
GND
/T_R
W/N
RSSI
THP
R726 1 8 C974
IFC
NC
NC
C962
+B
+B
CV
L500
8
4
C722
R792
C711
R721
IC404 C973
R797
C942 C907
R731 VAGC
C720
C760
R923
C506 12 13 4 5 R795
10 10
C939
C935
C931
C927
C923
C922
C920
C918
C972
C916
C905
R928
R901 C967 R926
C914
CN701
C724 R725
R709
C966
R925
Component side
C937
C933
C929
R703
R430
C713 C729
C703 Layer 1
Layer 2
11 J79-0128-19 A/2 Layer 3 11
Layer 4
Layer 5
Layer 6
Foil side
12 IC404 10G IC700 8H Q504 3D Q610 5I D501 7B D900 8P 12
IC500 9B IC701 9E Q505 6C Q704 6L D505 4B D901 5M
IC501 8C IC702 7K Q507 7C Q900 9P D518 7D D902 5P
IC502 7E IC900 4P Q604 6J Q901 7N D604 7J
IC503 5C IC901 9O Q605 3I Q902 7M D605 6I
13 IC504 7H IC902 5N Q607 4I Q904 9O D608 5I 13
IC600 4J Q503 7B Q608 4J Q905 4N D700 6L
68 69
14 14
TX-RX UNIT (X57-7370-10) (A/2) TX-RX UNIT (X57-7370-10) (A/2)

Foil side view (J79-0128-19 A/2) Foil side view (J79-0128-19 A/2)
2 2
C645
C650
L610 C643
C547 R544
C648 R545
L508
L607
3 C642 3
C654
L509
R646 R542 C548
R639
L609
C975
R663
C632 C556
C546
R543
C635
L606
C557
D506
L514
L516
R575
C634
C629
R636
C639
R644
D507
L614
C647
C652
C661
R665
R666
C667
L613
L515
L517
R667
TX-RX UNIT
C669
R576
D515
C660
C627
R559
D
R650
4 4
(X57-7370-10) (B/2)
D510
D514
D Q606 G D517
R561
C668
L611
C665 Q603 S L518
D511
D516
L525
J79-0128-19 B/2
D607
C568 C566 L519
D606
G
L526
C571
L612 C567 C565
C666
C663 CN600 C575 L521
C623
C625
R627
R632
R630
R631
5 5
L605
C579
C574
D519
R634
G
C670
C664 C662 + L522
L520
Q508
L723
R620
G
D
R599
S
C577
R560
Q509
L603
C570
C952
R929
R628
R626
D709
D
S
26 POW OPT6 25 C621
C954
C803
Q602
D S
S G
TXI RXEI D711 C573 L524
6 R915 C691 C581 6
C614
R623
R608
RXEO TXO L725 C583 C576
C618 L527 C580
OPT2 OPT7 C587 Q511
C810
R564
CN902
C615 R622 C689
C809
G
R624
3
C585
C584
R563
R607
IC903
OPT11 OPT8 L604
R565
L528
R790 C850 D
C849
DTI OPT9 L615 C671 C605 S

4
Q512
C617
CN737
C619
Q510 R568
C613
5V AGND R791 R617 L600
C811
L726
D710 R606 S D
C586
7 NC NC 7
C588
C607
C582
R562
C612 L602 C604 G G
R558
C799
AGND DGND
Q601
C610 D S
C970
C965
C968
OPT5 OPT10 R777 R618 C690 R604

C751
C754
C747
C804 C807 D600 R616
R774
R788 C801
Q600 C578
R605 C603
D708
OPT4 NC R773 C753 C611 L523

R786
L709
D601
26P_TD 26P_RD L722
C755
C749
R742 R612
R609
R610
1 5 C780 L710
R762
2 OPT3 OPT1 1 R912 L716
S C744
C802
C800
8 IC703 8
R768 L711
C756
C798
C712
C708
Q903
C769 C707
D S
G G
S D
3 4
C783
C794 R785
R772
D706
C777
C779
R744 L780
CN702
C715
R761 C706
BPF
C730
L721 R775 R769
C733
C732
C750 L705
C704 L703
R745
TXD1 RXD1 R917 C788 C741 R747 C748 C739 C725
C796
C795
R739 C738
R746
C700
R571
R702
L706 R728
L720
R919
C790
R778
Q700
9 9
L701
C789
C742 G S C719
C740
C752 L704
C785
R779 Q703
R748
C773 C768 L708
R771 G D
R799
L715
R733
C701
C901
C944 G S
C774
L714 C746 XF700
Q701
R743
Q705 C782
R701
R750
R765
G D R753 C758 R752

R770 C778 D704 R749 C743 L707
C734
D705
L713
C776
C770
C772
C767
C764
R784
R740
C786 C745 CF700
10 10
C784
Q706 L717 R760

C775
C721
R781
R783
C737 R737
G
S
R730
C718
D
Component side D703

D702
C771 R759
R780
R710
Layer 1 R757 C765
C791
Layer 2
11 Layer 3 J79-0128-19 A/2 11
Layer 4
Layer 5
Layer 6
Foil side
12 IC703 8H Q600 7P Q703 9K D511 4R D601 8O D706 8E 12
IC903 7D Q601 7N Q705 10F D514 4Q D606 5H D708 8E
Q508 5P Q602 6N Q706 10E D515 4P D607 5G D709 6G
Q509 6Q Q603 4N Q903 8D D516 4R D702 10I D710 7E
Q510 7R Q606 4L D506 4P D517 4R D703 10I D711 6F
13 Q511 6R Q700 9R D507 4Q D519 5R D704 10H 13
Q512 7Q Q701 10O D510 4Q D600 7M D705 10E
70 71
14 14
Note : The components marked with a dot (●) are parts of layer 1.
LCD
TX-RX UNIT (X57-7370-10) (A/2)
HD2 HD2 HD2 HD2 HD2 HD2 SWITCH UNIT (X41-3720-10) TH600 CN600
C459 DC SW DC SW THP THP THP THP RF FINAL AMP R : 0.5mV ANTENNA SWITCH
5 5 5 5 5 GPIo7 GPIo7 GPIo7 GPIo7
POWER SUPPLY T : 1.615V
L101 470p 19 19 19 19 19 19 19 D405,406,IC407 50T 50T 100k Q606
C637
470p
D606 L612 L613 L614
+B
6 6 6 6 6 CN402 Strip line
ASQDET 33A-1 33A-1 CN23 33M DC/DC CONVERTER 7.49V -t R : 12mV RD07MVS1BT122 R663 C660 HVC131 C663 4T 4T 4T
C460 /T R RF DRIVE AMP
15M
33M
SWITCH UNIT CN900 1 1
33A
AUD_IREFC A L102 AGND 14 VOLTAGE L402 Q414 Q415 T : 2.34V ANT
X2_CLKIN X2_CLKIN VOL SW/ENC CONTROL +B +B 1 LED_G 50C 50C
33A
33A
33A
5A
REGULATOR (33M) L401
C136 0.01u
+B
5A
L410 EMD12 EMD12 (X41-3710-10) C634 0 100p 100p
C138 0.1u
C139 0.1u
AD12_IREFF 6800p A 6_/KEYI0 LED_G Q603 C665 C667
C137 1u
A R20 1k D607
R13
C18
C16
U18
U17
U16
C17
B16
V18
V17
B18
B17
A18
A17
V16
P12
P13
K14
13 D416 CN901
T17
T16
F15
R521
J14
RF AMP R : 14mV RD01MUS1-T113 470p
M1
C904 47p R650
G5
G4
D5
N4
D6
D4
C5
C3
U2
U1
H5
U3
H4
D3
C4
R667
A3
V2
V1
B2
B1
A2
A1
E6
K5
E5
K4
E4
A5
B3
P7
P8
F3
T1
F5
T3
F4
T2
L1
L3
VR1 6_/KEYI0
J4
J5
R : 5.14V IC404
10
82k
D A C461
C650
C975
C652
R493
C647
C654
22u BATT INT
L609
7.5p
7.5p
14 Q406 PTT 1 T : 2.81V 2p 1.5p
47p
18p
12p
A A R928
31BU
15M
33M
33M
33M
33M
33M
7.49V 2 /EMG
7T
POWER SW/AF VOL
SCTAMI
XC6204B332M HVC131
0
R21 1.2k Q602
HRB0502A
PTT
1000p
Q406,407 BL_SB 12 1SS388F
4
0
C470
C662
C417
R424
220p
E12 2SB1132(Q,R)
ADC1
NC21
NC11
DGND11
NC1
AVCC1
C639
R636
R644
NC30
NC20
NC10
DGND10
IFIR
NC29
NC28
NC26
NC23
NC19
NC18
NC16
NC13
NC36
NC9
NC8
NC6
NC3
MICIR
DGND13
NC25
NC15
NC35
DGND9
DGND8
DGND6
NC5
L606
DGND15
DGND5
AGND9
AGND8
AGND6
AGND3
NC22
NC12
NC2
DGND12
AGND5
NC27
NC24
NC17
NC14
NC34
AVCC10
DGND14
68k
NC7
NC4
DGND7
DGND4
AGND2
AVCC9
AVCC8
AVCC6
AVCC5
AGND7
AGND4
AVCC2
AVCC4
470p D702 R471 BL_SB PTT GND 2 L605
220
18n
39p
1p
R158 R819 2SK3077F C621 R628 R620 C670
C666
C668
C669
C664
A4 DGND3 R : 5mV TX TX
47
A R438 C905 47p 0
D406
L712 R548
VIN
SHDN
CN403 VOLTAGE 4 3 6.05V RF AMP H : 2.33V
SW
4p
4p
8p
5p
XTALI E11 PLD R22 1k 3.284V
C976
C558
L611
220n
470p
6_KEYO1 11 C543 T : 0.64V
1000p
NC CE Side_G 3 3 LED_R
47p
L513
R501 0
C449
C425
C445
S1
B4 DGND2 33A 1 REGULATOR 3.82V R : 4.75V R : 2.5mV 6.8n L : 1.626V
18n
0.1u
22 10k 6_KEYO1 15p 0 0 470p
C419
MA2S111-F R : 4.94V
4.7u
100k Side_G LED_R
R626
C627
DC SW H : 2.8V
L603
1u
1SS388F
R631
XTALo E10 33A 6KEY 47k IC414 Q601
15n
120
10p
2
R550
6 (AF AMP) 2 BUFFER AMP T : 4.8V LOCAL SWITCH T : 2.37V
150k
CN404 SIDE 1 Side_1 4 T : 4.98V
47
A R23 1k C906 47p 3p
C623
D405
A10 DGND1 2.2k 6_KEYO0 10 XC61CC5602NR R : 1.81V 2SC5636 C613 C671 C615 L : 1.96V
C113
C117
R785
6 VSS D408
15p
0.1u
0.1u
L714 R506 Side_1
6.8k
10u10
VOL_GND 2 PLD 6_KEYO0 Q408 TX/RX LED R : 1.1V
C416
C629
C415
5
VIN
32K 32I 33M
470p
L5
L607
+
R790 R511 1k
VoUT
IC407 LED_G 1 4 IFC TX/RX LED T : 1.89V
10u
BooST
R456
/RES
Side_2 5 L504
VDD
VDD
VSS
/WR
0.01u
L702 C525 C553 Q600
C645
C648
C642
DVDIo7 CONTROL
/CS
150p
A12 T : 1.27V D601
L610
0.1u
EMD12 C607 R609
V1
D1
LED_G
A0
V3
D6
D3
D0
DC/DC IFC
V5
D5
V2
D2
V4
D7
D4
1k R25 1.2k 5 1 Side_2 7p 7p 470p
GND
R617
BL_SB 9 LT1616ES6-PBF RESET SWITCH
L602
L403 2.2k
C635
R639
R646
1000p
CN104 DSPCK
470p
P6
C143 0.01u
18n
330
0.01u
R441
R431
2SC5636
C418
C469
VOL 3 33M VOUT VIN R : 100mV
470k
C145 0.1u
C146 0.1u
C147 0.1u
C148 0.1u
10k
33k
ASQDET CONVERTER C907 47p 1 LG
15k
C691
FB
L716 470k R512 100
C618
C913 47p
C943 47p
C945 47p
C946 47p
C144 1u
R452
DVDIo6 SIDE 2
470p
B11 /EMG 2 12n R : 0.79V
470k
L604
0.1u
R439 47p 10p C588 C603
R102
1000p
VOL TX TX
L615
470k
R121
R496 100k 7p 0
C109
C625
C442
R630
R107
470p
470p
T : 6.38mV HSC277
15n
100k
100k
0.01u
C409
C412
C467
R666
R665
R632
R607
/RINT CKo CONTROL /EMG
2.2k
P11 Q407 5 /SAVE Q900 R : 1.48V
L600
33k
C661
CONTROL UNIT (X53-4260-XX) S1 R24 1k A
470p
L711
270
270
22n
Q701 6_KEYO2 8 T : 0.81V
10k
R798 100k
C550
R425
C537
R622
CN1
1u
1u
R510 LED_G D900
R472
A11 DVDIo5 EN3 4 SB1 SB1 /SAVE
100
33k
UMG3N 6_KEYO2 UMG9N T : 1.36V
22k
5p
5p
R111 100k
1
CHANNEL SELECTOR 100k R513 1k Q505 10p 10p
R113 100k
R115 100k
R610
R605
C719 2SA1832(GR)F Q405 3.82V
3
LED_R 3
2
R900
4.7k
USRCKI L14 ENC3 Q402
R116 47k
R118 47k
10k
VSS
5 IC413 C908 47p B30-2278-05
C611
LED_R R624
C610
C690
R616
R612
AUDIO
470p
470p
0.1u
R26 1k C901 2SC5636
4.7k
NC
-7.24V H18 DVDIo4 7 6_/KEYI1 7
180
1k OPT10 C755 47p SSM6N16FE-F
11
1
R509 AF AMP SW
20
10
19
18
16
13
AGND 5 TPA6201A1DRBR
3
6 I2CCK H : 4.65V
15
5
12
2
17
14
4
5 5 A0 ADD0 H14 AMP 9 6_/KEYI1 A R514 1k IFC 4 390 47k R627 R634
R1 0.1u
C559
R549
6 I2CCK
470p
J18 DVDIo3 8 R466
270
L : 4.64V
0.01u
R741
R406 L1 A 470p R902
C643
C646
C649
IFC BUFFER AMP
150p
470k
R126 100
C689
C605
R103
R604
470p
1 8 SP- SP- SP- 6
L409
0.1u
A 1k R803
6.8k
R606
C604
A1 ADD1
470p
E13
1u
4
R508 0 0
330
/LCDRST 6 6 EN4 6 OPT SW
D1
1k
D0
D3
D5
D2
R459
D4
C630
C628
C632
R443
R623
C614
A16 MCDIAF SHUTDoWN Vo-
470p
470p
IC405 7 /5TC H : 0.62V
470k
C1 0.1u
1M K18 DVDIo2 9 SP LEVEL CONVERTER R515 1k /SAVE 5
10p
10k
D ENC4 10k R903
C6 1u
C5 1u
C4 1u
C3 1u
C2 1u
100k
1u
R11
0 IC402 C944 10
R464
LCD CONTRAST /5TC
100p
3.82V
470k
C429
C16
R474
A17 A2 ADD2 E7 1.5V /SAVE L : 0.42V
0.1u
R127 0 10k R435
D18
D600
33k
R407 TC7WZ245FK-F 1k R507 A 1k D18,19 VOLTAGE REGULATOR (15M) C910 47p 820
HZC6.8-E
L18 DVDIo1 EN1 7 4 Q405 SP- 5
100k
R747 A
R618
L715 7 R516 100
R2
IC1 A3 ADD3 M5 ENC1 19 ASQ DET A I2CCK 6 470p 50C 50C R608
M13
22
R461
G10
G11
G13
G12
A A C440 0.1u R725 D408
C11
C12
C13
D11
D12
D13
H13
H12
H11
H10
N13
B12
B13
E10
E11
E12
E13
K13
K12
K11
K10
SSM6N16FE-F 2 GND 8 I2CSDA LOCAL
F10
F11
F12
F13
L13
L12
J13
J12
J11
J10
SURGE 100k I2CCK
10k
A
4
3
2
1
LMC7101BIM5 10k 5 4 M18 DVDD10 1k 5 BYPASS 15M 7.46V I2CSDA R : 6.57V LR
TH1
100k
A4 ADD4 N5 R504 EN2 8 33k ABSORPTION SP+ 4 1SS301F A LED_R SWITCH

R517 1k 47
C149 0.01u
B2 GND 6 /5TC 7 T : 79mV
C151 0.1u
C152 0.1u
C153 0.1u
C154 0.1u
C155 0.1u
-t
10
100P
ENC2
VSS
IN-A
IN+A
C437 R489 A A
oUTA
C150 1u
D19
C17
N18 DVDD9 6 NOISE 3 50T 50T

NX300

Uploaded by

Copyright:

Available Formats

NX300

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NX300

Uploaded by

Copyright:

Available Formats

UHF DIGITAL TRANSCEIVER

Knob (PTT) Knob (PTT)

Plastic cabinet assy

Does not come with antenna. Antenna is available as an option.

Document Copyrights INTRODUCTION

Firmware Copyrights PERSONAL SAFETY

1. Modes 2. How to Enter Each Mode

Clone mode 3. Panel Test Mode

4. Panel Tuning Mode

Firmware version Used to confirm the internal firmware

1. Press and hold the [ ] key while turning the transceiver

cloning source. The following describes how to enter the

1. Precautions for Waterproof

2. Precautions for Disassembly ■ Removing the TOP packing (G53-1762-02)

Positioning holes Control unit

■ Inserting the Volume and Channel switch into

1. Overview 2. Frequency Configuration

1st MIX MCF SP

Base band circuit

Fig. 1 Frequency configuration

1st PLL OSC (PLL) 2nd OSC

Fig. 2 RF and IF circuit 9

3-4. Squelch Circuit IC702(1/2) IC711(2/2) Q704 D705 IC711(1/2)

EXT. MIC IC102 DSP

MM SCSW AMP VCO

Fig. 5 Audio band and Base band circuit

5. PLL Frequency Synthesizer

Fig. 7 PLL block diagram

6. Control Circuit 6-1. ASIC

Q901 SB3 8-2. Decode (QT/DQT/LTR/DTMF/2-tone/MSK)

IC414 IC405 15M

IC406 33A ASIC Analog,

SB1 Q402 /PSW IC108

Q408 Q401 /BINT

Fig. 8 Power supply circuit

IC1 IC LCD contrast Q404 FET SB2 switch control

IC102 IC DSP Q406,407 Transistor Voltage regulator (AF AMP)

IC104 IC 2 input AND gate Q410 FET DC switch

IC106 IC RTC Q412 FET DC switch

IC108 IC ASIC Q701 Transistor OPT switch

IC401,402 IC Bus switch Q703 FET W/N noise switch

IC404 IC Voltage regulator (33M) Q705,706 Transistor MIC AGC

IC406 IC Voltage regulator (33A) D1,2 LED 12key backlight

IC408 IC AF AMP D5,6 LED 12key backlight

IC410 IC IF AMP D9,10 LED 12key backlight

IC412,413 IC Audio AMP D12~16 Diode Reverse current prevention

IC417,418 IC Dual bus buffer D22 Diode RXD control

IC702 IC APC LPF D101 Diode 12key backlight switch

IC704 IC RX AF LPF D401~404 Diode 12key control

IC706 IC MIC AMP D407 Diode Reverse current prevention

IC708 IC Voltage regulator (5A) D409,410 Diode SP control

IC710 IC MOD/MIC summing AMP D412 Diode DC switch control

IC712 IC MIC switch D414 Diode TX LED switch

IC714 IC OPT switch D416 Diode 33M control

Q1,2 Transistor LCD backlight switch D701 Diode 5A switch

Q4 FET MIC shift control D703,704 Diode Detector

Q101,102 Transistor 12key backlight switch D706 Diode Detector

Q401,402 FET Level converter

IC903 IC Voltage regulator (33C) D706,708 Variable Vari-cap tune

C131 CK73HB1A104K CHIP C 0.10UF K C466 CK73HB1E682K CHIP C 6800PF K