BDA Bi-Directional Amplifier

General
NOTIFIER offers all the components required for design and installa-
tion of the Emergency Radio Communication Enhancement Sys-
tems (ERCES): signal boosters/bi-directional amplifiers (BDA),
batteries and battery enclosures, donor antennas, Distributed
Antenna Systems (DAS), coaxial cables, connectors and lightning
arrestors, power dividers and hybrid couplers, design services and
training.
SIGNAL BOOSTERS / BI-DIRECTIONAL AMPLIFIERS (BDA)
NOTIFIER Class B BDAs are high gain, high power band-selective
signal boosters/bi-directional amplifiers that can be designed and
customized to meet all public safety frequency band ranges. It is
intended to provide reliable two-way radio signal coverage inside
buildings, tunnels and other structures. The band selective design
delivers a reliable performance in even the most challenging RF Annunciator
environments.

Features & Benefits

• All public safety frequency bands supported, various models
available for:
– UHF: NF-BDA400-1B, NF-BDA400-2B
– VHF: NF-BDA150-1B BDA
– 800 MHz: NF-BDA800-1B
– 700 MHz: NF-BDA700-1B
– RF power overload and RF interference prevention.
– 700MHz and 800MHz: NF-BDA7800-2B
– Oscillation Detection Circuit prevents amplifier feedback.
• UL, CSFM, NFPA, IFC compliance:
– Automatic Uplink Squelch: Completely eliminates uplink noise
– All-inclusive and fully-integrated signal booster / BDA with from the BDA eliminating risk of interrupting public safety radio
UL2524 In-building 2-Way Emergency Radio Communication network.
Enhancement Systems Listing, CSFM Listing, NFPA 72 2010
• Excellent RF Performance:
Edition, NFPA 1221 2016 Edition and IFC 2018 compliance.
– Band/Channel-Selective modules provide high rejection of
– Does not require external DC power supplies, chargers or
unwanted, interfering signals. Multiple channels/bands are pos-
alarm interfaces or feeds.
sible within the same amplifier.
– Integrated dual power supply system with two independent AC
– High performance bandpass cavity-type duplexers minimize out
circuit breakers.
of band interference.
– Integrated battery charger function with built in intelligent bat-
– High Gain of up to 92dB on both uplink and downlink.
tery monitoring and diagnostics with automatic load testing.
– High Power – capable of producing up to 32dBm of RF power.
– 24 hour battery backup with the standard battery backup pack-
age. – High Linearity Amplifiers deliver signals with very low distortion
and low IM products.
– Ability to connect to NOTIFIER's SLC loop for monitoring of the
BDA at the FACP. – Highly Resilient to strong RF inputs – ensures optimal, inter-
mod-free performance.
– Six alarm relay outputs for the supervised BDA monitoring
Panel / Annunciator. – Reliable performance even in high RF environments with sig-
nals as strong as -20dBm.
– Dedicated supervised Annunciator to provide status on AC
power, antenna, charger and low battery. Annunciator mounts – Very low signal delay of <9us means no delay-produced RF dis-
in a standard electrical 2-gang box. tortion in the signal overlap areas.
– On board Diagnostics – Optimized not only for FM and phase 1 P25 but also for TDMA
and phase 2 P25 modulations.
– Donor antenna line monitored for integrity.
– Adjustable RF gain on both LNA and ALC modules.
– Event history logging that can be exported.
– Adjustable maximum power level.
– Optional Auxiliary Alarm.
– Multiple ALC/OLC circuits maintain the set power limit and pre-
– LCD displays BDA system status.
vent the power amplifier overload.
• High Reliability
– Built-in EOL resistors are selectable with the DIP-switch.
– Two high-efficiency power supplies are included for redun-
• Serviceability:
dancy.
– Modular Design with easy to swap and easy to test modules.
– Each module has an internal microcontroller that continuously
monitors its operation and measures the voltage, temperature, – Each module has a status indication LED light for easy trouble-
current, and other parameters. shooting and status monitoring.

DN-61014:C • 12/11/18 — Page 1 of 5

 – Easy to use gain and power settings. • Expandability:
– LED indication of signal strength. – Modular Design allows for easy updates and frequency band
– Convenient quick-disconnect terminals. changes.
– Easily accessible RF connectors. – Multiple boosters can be combined on the same antenna sys-
tem for multi-band operation.

Electrical Specifications
NF-BDA400-1B,
Specification NF-BDA150-1B NF-BDA800-1B NF-BDA700-1B NF-BDA7800-2B
NF-BDA400-2B
Frequency Range 450-490MHz UHF 150-174MHz VHF 806-815MHz Uplink 793-805 MHz Uplink 793-815MHz Uplink
851-860MHz Downlink 763-775 MHz Downlink 851-860MHz & 763-
775 MHz Downlink
Passband 100KHz -3MHz1 - - - -
Maximum Bandwidth, 3MHz -
- - -
each band
Maximum Gain 92dB max. 92dB max. 92dB (Typ)
(adjustable) (90dB typ.) (90dB typ.)
Gain Adjustment, 1 dB 50dB to 92dB = 42dB total adjustment range
attenuator increments
Maximum Composite
Output Power (i.e. 32dBm 30dBm 30dBm
30dBm 28dBm
single carrier max.
power)
Power Limiter
Adjustment, 1 dB 32dBm to 18dBm 30dBm to 16dBm 30dBm to 16dBm 30dBm to 16dBm 28dBm to 14dBm
attenuator increments
Impedance 50 Ohm
Maximum RF Signal -20dBm
Input Level for FCC
spurious limits
compliance
Absolute Maximum 0dBm continuous, +10dBm peak
Input RF Signal Level
Noise Figure <6.5dB typ.8dB <6.5dB typ.8dB <6.5dB typ.8dB max. <6.5dB typ.8dB max. <6.0dB typ. 7dB max.
max. max.
Trouble indications Two Form C relays for each of the troubles:
AC Power Status, Charger Status, Low Battery Capacity, BDA Trouble, Antenna Trouble and Aux Alarm. Second relay
contact set provided for a LED annunciator panel.
Event Logger Standard SD Card up to 16GB. Mini SD with adapter. Real time clock time stamp included.
AC Power Supply Two independent power supplies with 110-240VAC/2.1A 50/60Hz each.
Power Supply 91% (Typ.)
Efficiency
DC Power Supply Requires two (2) 75Ah 12V AGM Sealed L.A. batteries in series for Secondary power. Maximum Current Draw: 2.5A @24VDC
Run Time with standard 24 Hours under full load
2x75Ah 60% de-rated
Battery Backup
Battery Charging with Charging Current Limited to 5A max.
the Built-in Charger2
Operating -4°F to +77°F (-20°C to + 25°C)
Temperature3
FCC ID 2AHVPSB400M1A 2AHVPSB150M2A 2AHVPSB800M2A 2AHVPSB700M2A 2AHVPSB7800M2A
2AHVPSB400M2A
FCC Certifications FCC Title 47 Part 90, FCC Title 47 Part 15b
1
Multiple channels can be combined within the 3MHZ duplexer band-pass. Multiple bands can be combined in the same enclosure. Other channel
bandwidths may be available, please inquire with your specific requirements.
2Only use approved lead-acid batteries supplied by NOTIFIER along with the Signal Booster.
3
This system meets NFPA requirements for operation at -20 to 25º C / -4 to 77º F and at a relative humidity. However, the useful life of the sys-
tem's standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is
recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15-25º C/60-77º F.

Page 2 of 5 — DN-61014:C • 12/11/18

Mechanical Specifications

Dimensions Main Enclosure: 20.55”Wx24”Hx8.32”D

Overall Width Including Heatsinks: 23.23”
Overall Height Including Mounting Tabs: 26.22”

Signal Booster Enclosure Type Red, NEMA-4 Type (UL Type-4) approved aluminum enclosure

Weight – Standard Enclosure, Single Band Configuration, ~59lbs

NFPA Compliant Version with two power supplies

RF Connectors N-Female

Backup Battery Enclosure Red, NEMA-3R Type (UL Type-3R) approved, steel vented enclosure, holds two
75Ah batteries. 23"W X 13"H X 8.3"D

Typical BDA System Riser Diagram

DN-61014:C • 12/11/18 — Page 3 of 5

AGENCY LISTINGS AND APPROVALS BDA-ADP-RA-1: Right Angle N Male to N Female Adapter.
These listings and approvals apply to the modules specified in this BDA-GKCK-10: Coaxial Cable Grounding Kit.
document. In some cases, certain modules or applications may not
POWER DIVIDERS AND HYBRID COUPLERS
be listed by certain approval agencies, or listing may be in process.
Consult factory for latest listing status. BDA-PD2-4588-1: 2-way power divider/combiner, 450-880MHz,
50W, Wilkinson type.
• UL2524: S36081.
BDA-PD3-4588-1: 3-way power divider/combiner, 450-880MHz,
• CSFM: 7300-0028:0508.
50W, Wilkinson type.
• NFPA 72 Compliance, NFPA 1221 Compliance.
BDA-PD4-4588-1: 4-way power divider/combiner, 450-880MHz,
• IFC Compliance.
50W, Wilkinson type.
• FCC Title 47 Part 90, FCC Title 47 Part 15b.
BDA-PD2-1552-1: 2-way power divider/combiner,150-520MHz,
50W, Wilkinson type.
Ordering Information
BDA-PD3-1552-1: 3-way power divider/combiner,150-520MHz,
SIGNAL BOOSTERS / BI-DIRECTIONAL AMPLIFIERS (BDA) 50W, Wilkinson type.
NF-BDA400-1B: 450-490MHz,Single UHF sub-band, Class B BDA, BDA-PD4-1552-1: 4-way power divider/combiner,150-520MHz,
NOTIFIER 50W, Wilkinson type.
NF-BDA400-2B: 450-490MHz,Dual UHF sub-band, Class B BDA, BDA-DC6-3588-1: Directional Coupler 6dB, 350-880MHz
NOTIFIER BDA-DC10-3588-1: Directional Coupler 10dB, 350-880MHz
NF-BDA150-1B: 150-174MHz,Single VHF sub-band, Class B BDA, BDA-DC15-3588-1: Directional Coupler 15dB, 350-880MHz
NOTIFIER
BDA-DC20-3588-1: Directional Coupler 20dB, 350-880MHz
NF-BDA800-1B: Full 800 MHz Public Safety Band, Class B BDA,
NOTIFIER BDA-DC6-1317-1: Directional Coupler 6dB, 136-174MHz
NF-BDA7800-2B: Full 700 & 800MHz PS,Dual band, Class B BDA, BDA-DC10-1317-1: Directional Coupler 10dB, 136-174MHz
NOTIFIER BDA-DC15-1317-1: Directional Coupler 15dB, 136-174MHz
NF-BDA700-1B: Full 700 MHz Public Safety Band, Class B BDA, DAS ANTENNAS
NOTIFIER
BDA-FA-450470-1: DAS Antenna, Fiberglass 450-470MHz
BATTERIES AND BATTERY ENCLOSURE BDA-FA-465490-1: DAS Antenna, Fiberglass 470-490MHz
BDA-BENCL-10-UL3R: NEMA-3R, UL Listed, Battery Enclosure for
BDA-FA-150175-1: DAS Antenna, Fiberglass 150-175MHz
2 x 75Ah Batteries. Steel with Red powder coat finish. Vented.
BDA-FA-700-1: DAS Antenna, Fiberglass 763-805MHz
BDA-BB-75-10: Battery, 12V/75Ah each. (two are required for each
BDA/signal booster). BDA-FA-800-1: DAS Antenna, Fiberglass 806-869MHz
BDA-SBR-10-UL3R: Seismic bracket kit for BDA battery enclosure. BDA-FA-7800-1: DAS Antenna, Fiberglass 763-869MHz
Includes a pair of brackets for two 75Ah batteries and the mounting BDA-FA-7800-2: DAS Antenna, Fiberglass 763-869MHz
hardware.
BDA-LPA-4502700-1: DAS Antenna, Low Profile, Ultra Broadband
CABLE, CONNECTORS, AND LIGHTNING ARRESTORS 450-2700MHz
BDA-CABLE-10A-250: 250 ft. Cable, Red Jacket, Imprinted, 1/2" BDA-LPA-150175-1: DAS Antenna, Low Profile 150-175MHz
Corrugated Alum Plenum Air Dielectric, 50 Ohm Coaxial.
BDA-LPA-7800-1: DAS Antenna, Low Profile 763-869MHz
BDA-CABLE-10A-500: 500 ft. Cable, Red Jacket, Imprinted,1/2" BDA-DP-7800-2: DAS Antenna, Directional Panel 763-869MHz
Corrugated Alum Plenum Air Dielectric, 50 Ohm Coaxial.
BDA-DP-400-2: DAS Antenna, Directional Panel UHF
BDA-CABLE-15A-250: 250 ft. Cable - Black Jacket,Imprinted,1/4"
Corrugated Copper Foam Dielectric, 50 Ohm Coaxial. DONOR ANTENNAS
BDA-CABLE-15A-500: 500 ft. Cable - Black Jacket,Imprinted,1/4" BDA-DA-450470-1: Donor Antenna, Yagi Directional 450-470MHz
Corrugated Copper Foam Dielectric, 50 Ohm Coaxial. BDA-DA-465490-1: Donor Antenna, Yagi Directional 470-490MHz
BDA-NMC-10: N-Male Connector for 1/2" cable. BDA-DA-150175-1: Donor Antenna, Yagi Directional 150-175MHz
BDA-NFC-11: N-Female Connector for 1/2" cable. BDA-DA-800-1: Donor Antenna, Yagi Directional 806-869MHz
BDA-NMC-20: N-Male Connector for 1/2" cable, RFS Omni-fit. BDA-DA-700-1: Donor Antenna, Yagi Directional 763-805MHz
BDA-NFC-21: N-Female Connector for 1/2" cable, RFS Omni-fit. BDA-DA-7800-1: Donor Antenna, Yagi Directional 763-869MHz
BDA-NMC-30A: N-Male connector for 1/4" Cable, Commscope. BDA-DA-LP582700-1: Donor Antenna, Log-Periodic Directional
BDA-NFC-31A: N-Female connector for 1/4" Cable, Commscope. Broadband 580-2700MHz, High FB Ratio
BDA-NMC-40A: N-Male connector for 1/4" Cable.
SERVICES
BDA-NFC-41A: N-Female connector for 1/4" Cable.
BDA-SVC-10: BDA System Design, Drawings, BOM (Unit Ea.)
BDA-EOL-10: Antenna Sensor / End of the line termination.
BDA-SVC-11: AHJ Requirements Review, Project management
BDA-JMPRG-10: Coaxial Cable Jumper NM-NM RG58, 18" long. (Unit Ea.)
BDA-JMPRG-11: Coaxial Cable Jumper NM-NM RG58, 37" long. BDA-TRAINING-1DAY: BDA Training, 1 DAY Unit
BDA-LA-P8AX-6G: Coaxial surge protector, UL listed. BDA-SVC-IBWAVE: BDA System - iBwave Services (Unit Ea.)
BDA-JMPRG-12: Coaxial Cable Jumper NM-NM Flexible RG8, 24"
long, For Donor Antenna.

Page 4 of 5 — DN-61014:C • 12/11/18

 This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.

©2019 by Honeywell International Inc. All rights reserved. Unauthorized

NOTIFIER use of this document is strictly prohibited.
12 Clintonville Road
Northford, CT 06472
203.484.7161
www.notifier.com