Chlorine

Chlorine Disinfection
Chlorine is widely used for disinfection of drinking water and also for general disinfection and
decontamination. It is cheap, widely available and effective.
Chlorine Products
The following table lists common chlorine generating products and their typical chlorine content or
percentage strength.
Product Strength Remarks

High Test Hypochlorite (HTH) Usually in granular form. Stable
65% - 70%
(calcium hypochlorite) (≈2% active chlorine loss per year).
Chlorinated Lime, aka Bleaching
30% Usually in powder form. Not stable.
Powder
Liquid form. Not stable; only use if
Household Bleach
2.5% – 10% manufactured recently (< 3 months),
(sodium hypochlorite)
and stored away from heat and light.
Usually in tablet form, also available
Sodium Dichloro-Isocyanurate 50% - 60% as granules.
in granular form. Tablets pre-dosed
(NaDCC), used in products such 5mg to > 5 g active chlorine
for water treatment. Very stable
as “Aquatabs”. per tablet.
(shelf life ≈ 5 years).
The chlorine content should be listed on the product’s labelling or packaging. In some markets around
the world, chlorine solutions specifically produced for household water treatment are readily available.
For example, in Nepal, the brand Piyush is available as a 0.5% chlorine solution in a 60 mL bottle.
Household Bleach
Bleach products (sodium hypochlorite) are commonly used to disinfect drinking water at the household
level. However, it is important to ensure that the products do not contain soap/detergent or perfume.
The strength of the product must be determined in order to calculate the volume of bleach required to
disinfect a given volume of water. The following table illustrates the variation in chlorine content of
some household bleach products.
Brands of bleach and country of origin Chlorine content %

Eau de Javel (France) 2.6%
JIK (Kenya), Robin bleach (Nepal) 3.5%
Lejia (Peru) 6%
Lanvandina (Bolivia), Blanqueador cloro (Mexico) 8%
As can be seen, the strength of bleach products varies widely between countries, and also within the
same country (contact the manufacturer for this information if it is not given on the bottle). This is why
disinfection recommendations given as “drops per litre”, “spoons per drum” or similar, are product
specific.
January 2008 1
Disinfecting filtered water is a necessary final step in the water treatment process. Chemical
disinfection using chlorine has the benefits of being relatively quick, simple, and cheap and allows a
residual amount of chlorine to remain in the water to provide some protection against subsequent
contamination. Determining the correct dose to add to a particular volume of water is quite
straightforward.
Three things can happen when chlorine is added to water:
1. Some chlorine reacts through oxidization with organic matter and the pathogens in the water and
kills them. This portion of the added chlorine is said to be consumed.
2. Some chlorine reacts with other organic matter and forms new chlorine compounds. This portion is
called combined chlorine.
3. Excess chlorine that is not consumed or combined and remains in the water is known as free
residual chlorine (FRC).
Using an empirical process of trial and error is the best way to determine how much chlorine is
required to disinfect water. It is relatively simple to measure the FRC in water, therefore the procedure
is essentially adding increasing amounts of chlorine to the water until all reactions have occurred and
an acceptable level of FRC can be measured.
Recommendations for FRC concentrations are usually in the range 0.2 mg/L up to about 0.6 mg/L.
This range provides a balance between a reasonably effective residual and acceptable taste.
Procedure to Determine Chlorine Disinfection Dose

1. Fill 4 buckets of known volume (10 - 20 L) with the water to be treated.
2. Using a syringe or similar add a different amount to each bucket of the chlorine product to be
used. For example:
o Bucket 1 – 0.2 ml
o Bucket 4 – 1 ml
3. Wait 30 minutes and measure FRC in each bucket using a pool tester or similar. Example results
o Bucket 1 – 0 mg/L
o Bucket 2 – 0.1mg/L
o Bucket 3 – 0.4mg/L
o Bucket 4 – 1mg/L
4. Select the dosage which delivers the best level of FRC. In this case, Bucket 3 with 0.75 mL of the
chlorine product in 20 L gives a FRC of 0.4 mg/L.
Diluting the chlorine product to approximately 1% active chlorine or less makes the dose volumes
larger and easier to measure.
A simple and cheap method of measuring chlorine and pH is by using a pool tester kit (as used for
swimming pool water).
January 2008 2
A typical “rule of thumb” dose of chlorine is 5 mg of active chlorine per L of water to be treated. After
the chlorine reacts with the organic matter and pathogens in the water, the aim is to have a FRC
content of approximately 0.5 mg/L.
Once the percentage chlorine content is known for a product, it is straightforward to calculate how
much of the product to add to a particular volume of water to achieve the 5 mg/L dose.
For example: 1 L of a bleach solution containing 2% chlorine equates to 20 000mg/L of chlorine. To

treat 20 L of water requires 100 mg of chlorine. Therefore the volume of bleach product to add in
mL = 100/20 000 x 1 000 = 5 mL
The quantity of chlorine required (the chlorine demand) depends mainly on the amount of organic
matter, and the number of pathogens. The efficiency and speed of the disinfection process is affected
by the chemistry of the water, pH, and temperature. All of these factors can vary from day to day and
in different seasons. Therefore, giving a reliable rule of thumb quantity of chlorine to use and a contact
time is not always straightforward.
pH
The optimum range for chlorine disinfection is between 5.5 and 7.5 (effectiveness of chlorine
disinfection can reduce by a factor of between 3 and 6 when pH rises from 6 up to 9). Chlorine
disinfection is not reliable when the pH is above 9.
If ph is above the 5.5 - 7.5 range then the:
• pH can be adjusted which is not very practical at the household level.

• Quantity of chlorine can be increased. Aim for a higher FRC at the end of the contact time (0.5
mg/L from pH 7-8, and 0.6 mg/L from pH 8-9).
• Contact time should be lengthened.
Temperature
At 18 - 20˚C and above, a contact time of 30 minutes is adequate. For every 10˚C drop in temperature
the efficiency of disinfection reduces by 50-60% (at close to 0˚C disinfection efficiency is very poor).
• Double the contact time if temperature falls to 10˚C

• At least quadruple contact time if temp is approaching zero.
In a community where all the householders take their water from a single source it is fairly
straightforward to sample a number of filters and determine an appropriate chlorine dose and contact
time. Where multiple sources of water are used, it should still be possible to arrive at a dose which will
be appropriate for the majority of users. To avoid confusion, it is probably better to use a single dose
recommendation for a community rather than multiple doses depending on source water.
The combined chlorine compounds are responsible for the strong chlorine taste and smell that is
sometimes apparent in treated water. Water with little or no combined chlorine and a FRC level in the
0.3 - 0.6 mg/L range usually does not have a strong smell or taste of chlorine.
January 2008 3
Precautions when Handling Chlorine Products

Household bleach is a common cleaning product found in many households, however chlorine is an
aggressive and corrosive chemical, and certain precautions must be taken.
Household bleach degrades and loses strength quite quickly after manufacture. The loss of strength is
faster if it is not kept in sealed containers and stored in a cool, dark place. To ensure that the chlorine
content is close to the design strength, verify that the product is not older than three months and that it
has been transported and stored properly.
Precautions
Protect the eyes and skin when handling chlorine granules and solutions:
• Prepare chlorine solutions in a well-ventilated area, preferably in the open air.
!
• Use plastic equipment and containers to prepare and store chlorine solutions.
Storage
Chlorine products and solutions lose strength rapidly with exposure to air, sunlight, and heat:
• Store products and solutions in plastic or plastic lined containers, and keep closed.
• Store products and solutions in a cool, shaded (ideally dark) area.
January 2008 4

Chlorine

Uploaded by

Copyright:

Available Formats

Chlorine

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chlorine

Uploaded by

Copyright:

Available Formats

Chlorine Disinfection

Product Strength Remarks

Brands of bleach and country of origin Chlorine content %

Three things can happen when chlorine is added to water:

Procedure to Determine Chlorine Disinfection Dose

For example: 1 L of a bleach solution containing 2% chlorine equates to 20 000mg/L of chlorine. To

If ph is above the 5.5 - 7.5 range then the:

• pH can be adjusted which is not very practical at the household level.

• Double the contact time if temperature falls to 10˚C

Precautions when Handling Chlorine Products

You might also like