Scribd
Upload
17K views4 pages

C1425 Open in Stop Light Switch Circuit

Uploaded by

Daniel rodriguez alayo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
17K views4 pages

C1425 Open in Stop Light Switch Circuit

Uploaded by

Daniel rodriguez alayo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Print Preview Exit

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS VEHICLE STABILITY CONTROL SYSTEM C1425 Open in Stop
Light Switch Circuit

DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop
light switch.
The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the
stop light signal input line.
DTC No. Detection Item DTC Detection Condition Trouble Area

· Wire harness or
When voltage at terminal +BS is 9.5 to 17.4 V, connector
Open in Stop Light Switch open circuit occurs between STP terminal · Skid control ECU
C1425
Circuit circuits A and B for 0.3 seconds or more (Brake actuator
(except restart due to stop and start control*). assembly)

*: w/ Stop and Start System

WIRING DIAGRAM

Luzgardo Hilari - Infotecnica Service


CAUTION / NOTICE / HINT

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

PROCEDURE

1.CHECK STOP LIGHT OPERATION

a. Check that all stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF

Result:
Proceed to
OK
NG

OK

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

CHECK STOP LIGHT CIRCUIT

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

a.

Front view of wire harness connector


*a (to Skid Control ECU [Brake Actuator
Assembly])

Luzgardo Hilari - Infotecnica Service


Turn the ignition switch off.

b. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

c. Disconnect the A4 skid control ECU (brake actuator assembly) connector.

d. Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Switch Specified
Connection Condition Condition
Stop light switch
assembly on
8 to 14 V
(Brake pedal
A4-35 (STP) - depressed)
Body ground Stop light switch
assembly off
Below 1.5 V
(Brake pedal
released)

Result:
Proceed to
OK
NG

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT


CIRCUIT)

3.RECONFIRM DTC

a. Reconnect the A4 skid control ECU (brake actuator assembly) connector.

b. Clear the DTCs.


Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK /
CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs

Execute

c. Turn the ignition switch off.

d. Start the engine.

e. Depress the brake pedal several times to test the stop light circuit.

f. Check if the same DTC is recorded.


Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK /
CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes

Luzgardo Hilari - Infotecnica Service


Execute

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the
next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM
SYMPTOMS TABLE

Result:
Proceed to
DTC C1425 is not output
DTC C1425 is output

DTC C1425 is not output

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO


PROCEED WITH TROUBLESHOOTING

DTC C1425 is output

REPLACE BRAKE ACTUATOR ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL

© 2012 TOYOTA MOTOR CORPORATION. All Rights Reserved.

Luzgardo Hilari - Infotecnica Service

You might also like