ERW broch August 11 2008 9/1/08 7:43 AM Page 1
C M Y CM MY CY CMY K
Table 1.
Electric Resistance Welded Pipe
ERW/HFI
Hall Longmore uses the high frequency induction heating
(HFI) process to manufacture pipes ranging in nominal diameter
from 219 mm (8,58 inch) to 610 mm (24 inch), and in wall
thickness as shown in Table 1.
Edge milled steel coil is mechanically formed into pipe
after which a high-frequency electrical current is applied to
fuse pipe skelp to form a weld. Unlike the arc-welding
process, no filler material is added. The weld joint becomes
a homogeneous part of the completed pipe.
In order to ensure completely smooth pipes, welds are scarfed
both internally and externally. Immediate confirmations of
welds are assured as pipes pass through a multi-probe
ultrasonic inspection system located after the welding and
scarfing stations.
Following ultrasonic assessment, weld joints are induction
heated to normalise the metallic structure of the weld.
Normalising also improves toughness of the steel in the region
and significantly decreases the weld line corrosion effect.
Prior to hydrostatic testing, pipes are sized to required
tolerances before being cut to length and the ends bevelled.
Weld seams is again ultrasonically tested.
Pipes are inspected, weighed and can be varnished and
marked prior to final inspection and dispatch, or transferred
to the coating and lining plants for corrosion protection
treatment.
Osborn Road, Wadeville,
Johannesburg, South Africa
Tel: +27 11 874 7300
Fax: +27 11 824 4962
E-mail:
[email protected] Web: www.hall-longmore.co.za
ERW broch August 11 2008 9/1/08 7:43 AM Page 2
C M Y CM MY CY CMY K
ERW manufacturing facilities Seam Annealing
Post welding the heat-effected zone is seam annealed to ensure a fine
Hall Longmore ranks amongst the most reputable ERW pipe producers grained micro structure with superior mechanical properties.......................
internationally and satisfies specifications set by leading oil and gas companies.
Sizing, Cut-off and Bevelling
Coil Magazine and Decoiling
This completes final pipe geometry to meet client specification requirements.
The Hall Longmore 30 ton/ 2,5 m OD coil magazine and decoiling station
for constant strip feeding, is recognised as one of the most modern in the
world. Hydrostatic Testing and Final Ultrasonic Inspection
This process qualifies pipe integrity with testing pressures of up to
Edge Milling 300 bar and six ultrasonic probes with full coupling control for final weld
inspection. Pipe ends are manually inspected ultrasonically when required.
The Linsinger Edge Milling equipment has the capability of precision milling
high-grade steel up to X70. It is possible to edge mill a maximum width
of 15 mm/side at a speed of 19 m/minute at a wall thickness of 12,7mm. In-house Testing Facilities
Facilities include: Hardness and tensile strength; Charpy V-notch;
Steel Strip Lamination Inspection Spectrographic and Metallographic assessment and drop weight tear
testing machine (DWTT).
It is important that steel strip is inspected for lamination defects in order
to ensure overall quality of the line pipe. Edge Lamination and Strip Width
Ultrasonic Inspection systems employed in-line are constantly monitoring
the possible occurrence of such defects using equipment supplied by
Krautkrämer-Germany.
Round Forming
The most advanced automatic forming system comprising pre-forming
cage, breakdown, edge forming and final forming cage, ensures perfect
shape and edge geometry which is required for a consistent quality weld
especially in high steel grades.
Welding / High frequency induction
The 1000 kW High Frequency Contact Welder ensures full control of the
welding process for repeatable high quality welds particularly in high steel
grades. Frequency range > 100 kHz.
In-line Ultrasonic Systems
The ultrasonic systems designed by Krautkrämer monitor the weld integrity
and measure weld bead geometry after internal and external scarfing.
Mill operators therefore maintain consistent quality at the most critical zone
in the pipe: the weld seam.
ERW broch August 11 2008 9/1/08 7:43 AM Page 2
C M Y CM MY CY CMY K
ERW manufacturing facilities Seam Annealing
Post welding the heat-effected zone is seam annealed to ensure a fine
Hall Longmore ranks amongst the most reputable ERW pipe producers grained micro structure with superior mechanical properties.......................
internationally and satisfies specifications set by leading oil and gas companies.
Sizing, Cut-off and Bevelling
Coil Magazine and Decoiling
This completes final pipe geometry to meet client specification requirements.
The Hall Longmore 30 ton/ 2,5 m OD coil magazine and decoiling station
for constant strip feeding, is recognised as one of the most modern in the
world. Hydrostatic Testing and Final Ultrasonic Inspection
This process qualifies pipe integrity with testing pressures of up to
Edge Milling 300 bar and six ultrasonic probes with full coupling control for final weld
inspection. Pipe ends are manually inspected ultrasonically when required.
The Linsinger Edge Milling equipment has the capability of precision milling
high-grade steel up to X70. It is possible to edge mill a maximum width
of 15 mm/side at a speed of 19 m/minute at a wall thickness of 12,7mm. In-house Testing Facilities
Facilities include: Hardness and tensile strength; Charpy V-notch;
Steel Strip Lamination Inspection Spectrographic and Metallographic assessment and drop weight tear
testing machine (DWTT).
It is important that steel strip is inspected for lamination defects in order
to ensure overall quality of the line pipe. Edge Lamination and Strip Width
Ultrasonic Inspection systems employed in-line are constantly monitoring
the possible occurrence of such defects using equipment supplied by
Krautkrämer-Germany.
Round Forming
The most advanced automatic forming system comprising pre-forming
cage, breakdown, edge forming and final forming cage, ensures perfect
shape and edge geometry which is required for a consistent quality weld
especially in high steel grades.
Welding / High frequency induction
The 1000 kW High Frequency Contact Welder ensures full control of the
welding process for repeatable high quality welds particularly in high steel
grades. Frequency range > 100 kHz.
In-line Ultrasonic Systems
The ultrasonic systems designed by Krautkrämer monitor the weld integrity
and measure weld bead geometry after internal and external scarfing.
Mill operators therefore maintain consistent quality at the most critical zone
in the pipe: the weld seam.
ERW broch August 11 2008 9/1/08 7:43 AM Page 1
C M Y CM MY CY CMY K
Table 1.
Electric Resistance Welded Pipe
ERW/HFI
Hall Longmore uses the high frequency induction heating
(HFI) process to manufacture pipes ranging in nominal diameter
from 219 mm (8,58 inch) to 610 mm (24 inch), and in wall
thickness as shown in Table 1.
Edge milled steel coil is mechanically formed into pipe
after which a high-frequency electrical current is applied to
fuse pipe skelp to form a weld. Unlike the arc-welding
process, no filler material is added. The weld joint becomes
a homogeneous part of the completed pipe.
In order to ensure completely smooth pipes, welds are scarfed
both internally and externally. Immediate confirmations of
welds are assured as pipes pass through a multi-probe
ultrasonic inspection system located after the welding and
scarfing stations.
Following ultrasonic assessment, weld joints are induction
heated to normalise the metallic structure of the weld.
Normalising also improves toughness of the steel in the region
and significantly decreases the weld line corrosion effect.
Prior to hydrostatic testing, pipes are sized to required
tolerances before being cut to length and the ends bevelled.
Weld seams is again ultrasonically tested.
Pipes are inspected, weighed and can be varnished and
marked prior to final inspection and dispatch, or transferred
to the coating and lining plants for corrosion protection
treatment.
Osborn Road, Wadeville,
Johannesburg, South Africa
Tel: +27 11 874 7300
Fax: +27 11 824 4962
E-mail:
[email protected] Web: www.hall-longmore.co.za
