DeltaV CHARM

DeltaV Distributed Control System Product Data Sheet
November 2019
DeltaV Electronic Marshalling

I/O anywhere you need it
Single channel granularity
Reduces installed cost of system
Fully redundant architecture
Field-mounted capable hardware
Plug and play I/O
The DeltaV CHARM I/O Card (CIOC) with CHARMs.
Introduction Single channel granularity: The CHARM I/O architecture

allows each individual channel to be characterized for the
DeltaV™ Electronic Marshalling delivers a new level of control requirements of the field device. Any instrument signal can be
system I/O performance with unprecedented flexibility and wired to any terminal block. The channel is then electronically
ease of use. The CHARM I/O card (CIOC) supports up to 96 marshalled by installing the appropriate CHARM and assigning
individually configurable channels and is designed specifically the channel to one of four controllers. Home run multi-core
for multi-core home run cables in centrally located marshalling instrument cables can be landed in order on a series of CHARM
cabinets. It can also be installed in field junction boxes to terminal blocks without concern for signal types.
further reduce system design and installation costs. All
Reduces installed cost of system: DeltaV Electronic
communications are completely redundant from the
Marshalling helps reduce overall system costs by eliminating
channel (CHARM) to the DeltaV controller.
internal cabinet cross wiring, reducing overall footprint,
simplifying I/O channel assignments, and reducing Factory
Benefits Authorized Testing activities. Electronic Marshalling provides
separation between I&E hardware installation schedules and
I/O anywhere you need it: DeltaV CIOC provides an
control strategy development. Wiring can begin earlier knowing
unprecedented flexibility in control system I/O topology.
any late changes can be done without lifting a wire. Separation
Using standard Ethernet infrastructure hardware you can add
of the controller and I/O allows more efficient cabinet designs
I/O anywhere you need it. From a local I/O cabinet to remote
and accommodates late scope changes you can add I/O
enclosures miles away, simply install the hardware and connect
anywhere. Adding additional control capacity does not require
it to the DeltaV control network. Each I/O card can serve I/O
re-wiring I/O. Simply assign the control modules and their I/O
signals to any four controllers in the system with 50-ms updates
signals to the new controller, without lifting a wire.
for fast, reliable control.
DeltaV Electronic Marshalling November 2019
Fully redundant communications: The CIOC architecture is Product Description

fully redundant. It starts with the two I/O cards on a carrier.
The carrier has redundant communication modules for primary Electronic Marshalling hardware includes:
and secondary network connections. There are two 24V DC
CHARM I/O Carrier (DIN rail-mounted and supports
input power connections. The carrier connects to the CHARMs
redundant pair of CHARM I/O Cards, redundant
baseplates and provides redundant power and communication
24 V DC power connectivity, and redundant Ethernet
buses to the CHARMs. Everything is redundant down to the
communication modules).
individual channel.
CHARM I/O Card (CIOC) provides communication between
Field-mounted capable hardware: All components of the
CHARMs and the Ethernet I/O network to M-series, S-series,
CIOC are rated for installation in Class 1/Div 2 or Zone 2
and PK controllers. The CIOC has Achilles Communications
hazardous locations. The extended operating temperature
Certification Level 1 and the redesigned CIOC2 has more
ranges and G3 environment rating allows them to be installed
computing power and Achilles Communications Certification
in field-mounted junction boxes. This further reduces the
Level 2. The CIOC2 is a drop-in replacement for the CIOC
footprint required in central equipment rooms, as well as
(v14.3 or later is required).
reduces the overall wiring infrastructure of traditional multi-
core instrumentation cable. CHARM Base plate (DIN rail-mounted with interleaving power
and bus connectors. Supports 12 CHARMs and their terminal
Plug and Play I/O: The DeltaV CIOC has been designed for
blocks, as well as connection for injected field power).
ease of use, both in physical installation and its software
tools. Components snap together with secure DIN-rail latches CHARM Terminal Block (removable terminal block
and interlocking carrier connectors. Attach a series of 96 providing terminal connections to field wiring and
I/O channels to a DIN-rail in a matter of minutes. Insert the physical latch for CHARM).
CHARMs and auto sense the node to create the I/O definition
CHARMs (Characterization Module for each field signal.
automatically in your DeltaV configuration database. CHARMs
Provides basic analog to digital conversion and signal
use a self keying system to automatically set a channel for a
isolation to the redundant communication bus).
specific CHARM type. Users cannot mistakenly insert a CHARM
into the wrong terminal block. Assign all, one or any number of Cable Extenders that provide flexibility in carrier mounting.
channels to a controller with a simple click or drag and drop. I/O bus termination (provides bus terminations for
redundant I/O bus).
Labeling features for baseplate and channel identification.
CHARM and Terminal Block.
Field power is provided through a redundant 24V DC bus to

each CHARM, with up to 100 mA per CHARM. Higher current
Channels can be powered through integrated power injection
bus local to each CHARM Baseplate.
CHARM I/O Card (CIOC) with CHARMs.
www.emerson.com/deltav 2
The CIOC carrier is mounted to the top of a vertical DIN rail and Baseplate extenders and cables provide great flexibility to the
up to eight CHARM Baseplates are mounted below it, snapping CHARM installation in existing cabinets or in custom enclosures.
easily to the DIN rail as they are connected to each other. The Cables are redundant, each carrying 24V DC field power,
bus termination assembly is attached at the bottom. A standard 6.3V DC CHARM power, and one of the communication busses.
DIN-rail lock is used to keep the entire assembly in place.
Bus termination provides added robustness for the
A pair of CIOCs installs on the carrier and communicates over communication bus and is installed at the end of the
a redundant Ethernet network with up to four controllers, physical bus.
allowing great flexibility and ease of system expansion.
Label features are available to identify channel usage and
Communication modules are available for copper and
Baseplate identification to help with maintenance.
fiberoptic media.
CHARMs can be added to any existing baseplate position and
Each baseplate is ordered with 12 terminal blocks: standard
autosensed online. Additional CIOCs can be added online.
terminal blocks, fused injected power terminal blocks, or relay
output terminal blocks.
CHARM Types
Electronic Marshalling eliminates the need to partition the I/O
wiring to specific channels based on signal type. Simply connect A variety of analog and discrete CHARMs are available to meet
field signal multi-cores in an orderly fashion as desired. Install your specific requirements. The following CHARMs are available
the appropriate CHARM to complete the field circuit and the starting with v11.3.1:
signal is ready to be used by any one of four controllers. No
AI 4-20 mA HART
cross-wiring required.
RTD
Each CHARM acts as a circuit protection device and field
wiring disconnect. Signals are inherently current-limited to Thermocouple / mV
protect against wiring faults to ground. Each CHARM provides
AI 0-10V DC Isolated
surge protection to meet industry standards in the area of
EMC. Under extreme overvoltage conditions due to incorrect AO 4-20 mA HART
field wiring, the CHARM will act as a fuse to protect adjacent DI NAMUR
channels. Signal faults are thus isolated to the single CHARM.
DI 24V DC low-side sense (dry contact)
CHARMs can be partially ejected to a locked position that
disconnects the field wiring from the system to perform field DI 24V DC Isolated
maintenance actions or to remove power to a field device. DO 24V DC High Side
Activating the CHARM latch ejects the CHARM to the detent
position. Closing the latch locks the CHARM in place and DO 100mA Energy Limited
isolates the field wiring for field work. DO 24V DC Isolated
24V DC Power
DI 120V AC Isolated
DI 120V AC Isolated Plus
DI 230V AC Isolated
DO V AC Isolated
CHARM Latch mechanism.
All CHARMs have a bi-color power/integrity LED that indicates Each baseplate has a local power bus that can be connected
the health of the CHARM. The indications provide clear, to 24V DC or 120/230V AC through the injected power input
actionable instruction to the maintenance personnel. terminals, located on the Address Plug terminal block. Both,
the fused-injected power Terminal Block, the 3-wire DI fused-
Green Solid: Normal Operation
injected power Terminal Block, and the 3-wire AI Fused Injected
Green Blink: Normal awaiting configuration Terminal block connect to this power bus to provide system
power to the field circuit through the isolated CHARM. You can
Red Blink: Fault detected on wiring
combine isolated and system powered circuits on the same
Red Solid: Internal Fault detected baseplate, however, all system powered channels on a baseplate
Discrete CHARMs have a yellow LED to indicate the state of the share the same power source.
field signal. (On = circuit is energized) The Relay Output Terminal Block is designed for high output
All CHARMs meet ISA 71.04-1985 severity level G3 (harsh) current applications and requires the DO 24V DC High-side
corrosion specifications. CHARM to drive the relay coil. The Relay Output Term blocks
provide a normally open and normally closed contact with the
24V DC based discrete input CHARMs support pulse counters following ratings:
with a maximum frequency of 10 KHz.
28.8V DC at 5 A switching current
I/O Terminal Block Options 48V DC at 0.4 A switching current
110V DC at 0.2 A switching current

There are six different I/O terminal blocks available to meet
the wiring needs of field signals. 250V AC at 5 A switching current
Standard Terminal Block The Thermocouple / mV Terminal Block is specially designed
for the usage with the Thermocouple / mV CHARM. The
Fused-Injected-Power Terminal Block
Thermocouple / mV Terminal Block has fixed key positions
3-wire DI Fused Injected-Power Terminal Block
to prevent a mismatch in the field and can only be ordered
Relay Output Terminal Block as an Assembly with the Thermocouple / mV CHARM.
Thermocouple / mV Terminal Block The 3-wire AI Fused Injected Power Terminal Block is
3-wire AI Fused Injected Power Terminal Block designed for 3 wire analog transmitters and can be used with
the AI 4-20mA HART CHARM. The field power is supplied from
The Standard Terminal block can be used with all CHARM the injected power bus on the baseplate, but the power is not
types. For traditional wiring of field instrumentation, the removed from the field device when the AI CHARM is removed
CHARMs provide loop power through the internally distributed from the baseplate. There is a Green LED on the terminal block
24V DC field power. Refer to specific CHARM specifications for that indicated power is supplied to the field and the 2A fuse
wiring information. also functions as a means to disconnect power from the field
The Fused-Injected-Power Terminal block, the 3-wire DI device. Although this terminal block was introduced in 2017,
Fused-Injected-Power Terminal block, and the 3-wire AI it is backwards compatible to any version of DeltaV with
Fused Injected Terminal block includes a 2A field replaceable Electronic Marshalling.
fuse. The 3-wire DI Fused-Injected-Power Terminal block Although any signal type can be installed in any location on the
is designed to be used with all isolated discrete Input CHARM CHARM baseplates, it is recommended that AC voltage circuits
types, while the Fused Injected Power Terminal block is be separated from low voltage signals to comply with safety
designed to work with all Isolated discrete Output CHARM recommendations and to mitigate induced noise in the signals.
types, the 3-wire AI Fused Injected Power Terminal block Standard Terminal blocks, Fused Injected Power terminal blocks
is used with AI 4-20mA HART CHARM type creating a system- and Relay Output Blocks can be used on the same carrier,
powered circuit that can deliver up to 1 amp (DC) to the field. typically, to allow the use of DO 24V DC isolated CHARMs
on higher wattage and 3-wire devices alongside of standard
24V DC instrumentation signals or relay contacts.
CHARM Keying Posts ASCO Numatics 580 CHARM Node

The Terminal Blocks contain keying posts that are automatically The 580 CHARM node enables Easy solenoid valve integration
set and locked to the unique position of the installed CHARM. into DeltaV with Electronic Marshalling. The new 580 CHARM
The keys prevent the insertion of an incorrect CHARM during node connects directly to the CIOC via redundant CHARM
maintenance activities. They are shipped in a neutral position Baseplate extender cables. DeltaV can autosense the I/O as DO
and are set when a CHARM is inserted. If needed, the keys Solenoid Valve CHARMs the same way as any other CHARM is
can be manually reset to allow a channel to be re-tasked for autosensed in DeltaV.
a different signal type.
Benefits of the new 580 CHARM Node include:
Redundant communications and power connections to

pneumatic valve manifolds,
Eliminates the need for additional dedicated networks like

Profibus-DP and simplifies system I/O mapping,
Expands the Electronic Marshalling I/O offering to include

ASCO Numatics pilot valve manifolds, enhancing the concept
of: “I/O Anywhere”, and
Reduces programming and commissioning time dramatically.
CHARM standard Terminal block.
The keying mechanism consists of two keying posts that rotate

and lock into the terminal block base. Each CHARM type is
assigned a unique key setting.
ASCO Numatics 580 CHARM Node.
Hardware Specifications
Common Environmental Specifications (all components)
Operating Temperature* -40 to 70°C (-40 to 158°F)**
Storage Temperature -40 to 85°C (-40 to 185°F)
Relative Humidity 5 to 95% , non-condensing
Protection Rating IP 20
Airborne Contaminants ISA-S71.04-1985 Airborne Contaminants Class G3 Conformal coating
Shock 10 g ½-sine wave for 11 ms
Vibration 1 mm peak-to-peak from 2 to 13.2 Hz, 0.7 g from 13.2 to 150 Hz

*Operating any electronics at the higher end of its temperature range for long periods of time will shorten its expected lifetime,
see Effects of Heat and Airflow Inside an Enclosure White Paper for more information.
** When used with copper Ethernet I/O Ports (Copper IOP). When used with the fiberoptic I/O Ports (fiberoptic IOP), the operating temperature range is limited to
-40 to 60°C (-40 to 140°F).
** When used with all CHARM Types except the DI 120 V AC Isolated Plus CHARM. When used with the DI 120 V AC Isolated Plus CHARM, the operating temperature
range is limited to -40 to 60°C (-40 to 140°F).
CHARM I/O Card and Carrier.
Operating Temperature -40 to 70°C (-40 to 158°F). Operating Temperature -40 to 60°C (-40 to 140°F).
CIOC Carrier Ethernet Communication Modules
CHARMs.
CHARM Baseplate with Identifier, CHARMs and Label Plates.

Depth with DI 120V AC Isolated CHARMs will increase from 10.43
to 14.75cm
CHARM Baseplate Terminator, Top.
DI 120V AC Isolated Plus CHARMs.
CHARM Baseplate Terminator, Bottom.
CHARM Baseplate Extender, Top.
CHARM Standard Terminal Block.
CHARM Baseplate Extender, Bottom.
CHARM 3-wire DI Fused-Injected-Power Terminal Block. CHARM Relay Output Terminal Block.
CHARM 3-wire AI Fused Injected Power Terminal Block. CHARM Thermocouple / mV Terminal Block.
CHARM Fused Injected-Power Terminal Block. Address Plug.
Address Plug Terminal Block.
CHARM I/O Card hardware

Specifications for CHARM I/O Card Carrier
Number of I/O Cards per Carrier 2 (redundant pair)
Input Power (Redundant) +24V DC ±10% at 12 A maximum
Redundant Ethernet connections via replaceable IOPs Fiberoptic: 100BASE-FX with MTRJ connectors;
Full duplex operation;
Multimode - 2 km nominal distance.
Copper twisted pair: 10/100BASE-TX with RJ45 connectors;
Full duplex operation
100 m distance
Mounting DIN rail Latch to vertical T-type rail
Specifications for CHARM I/O Card (CIOC) and CHARM I/O Card 2 (CIOC2)
Number of I/O Channels 96 Channels, individually defined signal types
Number of I/O Clients 4 (Controllers)
Number of CIOCs per Controller 16
Number of CIOCs per System 300
I/O Update Rates 50ms, 100ms, 250ms, 500ms
CIOC Power (24 V DC) 0.28 A per redundant CIOC node

0.32A per redundant CIOC2 node (includes two cards and
two communication modules) (individual CHARM power
requirements are in addition)
CIOC Heat Dissipation 8 Watts max. per redundant CIOC node
9 Watts max. per redundant CIOC2 node
2.0 Watts per CIOC
2.5 Watts per CIOC2
1.34 Watts per Copper Ethernet I/O Communication Port
2.0 Watts per Fiberoptic I/O Communication Port
CIOC output to CHARMS 6.3V DC redundant power, at 3.25 A maximum*
Fuse Protection (internal) Internal Non-replaceable Fuse
Mounting 2-wide CHARM I/O Carrier
Communication Redundant Ethernet connections through CHARM I/O Carrier
Network Addressing Auto Assigned during commissioning
LED Indicators
Green – Power Indicates DC power is applied
Red – Error Indicates an error condition
Green – Active/Standby Indicates operating mode of each CIOC
Yellow Flashing – Pri./Sec. CN Indicates valid control network communication

* Actual CIOC Output to CHARMs is dependent on number of installed CHARMs
CHARM Baseplate
Number of Channels per Baseplate 12
Number of Base Plates per CIOC 8
Addressing One Address Plug (1 through 8)
Terminal Blocks Standard Terminal Block

Fused -Injected -Power Terminal Block
3-wire DI Fused Injected Power Terminal Block
3-wire AI Fused Injected Power Terminal Block
Relay Output Terminal Block
Thermocouple / mV Terminal Block
Shield Connections 1 Screw Cage terminal per channel, plus 1 for cable shield
0.32 – 2.5 mm2 / 22 – 14 AWG
Gold plated connectors for shield continuity
Wire Strip Length 7 - 9 mm / 0.28 – 0.36 in
Mounting DIN rail latch to T-type rail
Specifications for Baseplate Termination, Top and Bottom

Shield Drain Wire Connections 2 Screw Cage Terminals
0.32 – 2.5 mm2 / 22 – 14 AWG
Wire Strip Length 7 - 9 mm / 0.28 – 0.36 in.
Specifications for Baseplate Extenders, Top and Bottom

Primary Bus Connection 9-pin D-shell,
Primary RS-485 communications bus
Primary 24V DC field power
Primary CHARM power
Secondary Bus Connection 9-pin D-shell,
Secondary RS-485 communications bus
Secondary 24V DC field power
Secondary CHARM power
Specifications for Extender Cables
Maximum Bus Length (including Baseplates) 5.5 m (18 ft)
Available Cable Lengths 2 m, 1 m, 0.5 m (6.7 ft, 3.3 ft, 1.6 ft )
Specifications for Standard Terminal Block

Number of Connections 4 Screw Cage terminals 0.32 – 2.5 mm2 / 22 – 14 AWG
Strip Length 7 - 9 mm / 0.28 – 0.36 in.
Maximum Current 2 A max. at 250V AC max. *
Color Black
Specifications for 3-wire DI Fused Injected-Power Terminal Block

Strip Length 7 - 9 mm / 0.28 – 0.36 in
Field Replaceable Fuse 2A
Color Black
Specifications for 3-wire AI Fused Injected Power Terminal Block
Maximum Current 30mA max. at 30V DC max. (screw terminal #2)

1 A max. at 30V DC max. (screw terminals #3 and #4)*
Color Black
LED Indicator Green – Power going to field
Specifications for Fused Injected-Power Terminal Block

Color Black
Specifications for Relay Output Terminal Block

Strip Length 7 - 9 mm / 0.28 – 0.36 in.
Maximum Current 5 A at 28.8V DC / 0.4 A at 48V DC / 0.2A at 110V DC/5 A

at 250V AC
Color Black
Specifications for Thermocouple / mV Terminal Block

Color Black
Specifications for Address Plug Terminal Block

Number of Connections 2 sets of 2 connections
Screw Cage terminals 0.32 – 2.5 mm2 / 22 – 14 AWG
Maximum Current 10 A max. at 250V AC max. **
Color Black
*Actual Current draw is determined by type of CHARM and associated field devices.
**Actual Current draw through the Address Block Terminal Block is determined by the combined current draws through Injected-Power Terminal blocks on each CHARM Baseplate.
Analog Input 4-20 mA HART CHARM

Specifications for AI 4-20 mA HART CHARM
Sensor Types 4-20 mA with or without HART 0-20 mA
Supports 2-wire and 4-wire device types directly Supports
3-wire device powered through the 3-wire AI Fused Injected
Power Terminal Block or the 24V DC Power CHARM
Nominal Signal Range (Span) 4-20 mA, (0-20 mA optional)
Full Signal Range 0 to 24 mA
Input Impedance 250 Ω ±1%
Field Power (2-wire) 15.0V at 20 mA @ 24V DC input
Accuracy Over Temperature Range 0.1% of span (0-60°C)

0.25% of span (over -40 -70°C)
Repeatability 0.05% of span
Resolution 16 bit A/D converter
Calibration None required
DC/50/60 Hz Common Mode Rejection N/A
Field Circuit Protection 30 mA Current Limiting circuit

Field wiring disconnect
CHARM Power Req. 36 mA max @ 24V DC for two wire configuration
12 mA max @ 24V DC for three and four wire configuration
CHARM Heat Dissipation 0.33 W
HART Support HART v7 pass-through for AMS

HART v7 variable and device status available to control
HART Data Update Rates Update rates are faster than every second dependent
on HART communication loading and device type
Simplified Circuit and Connection Diagrams for AI HART CHARM 0/ 4 to 20 mA Two-Wire and Four-Wire transmitters.
Simplified Circuit and Connection Diagrams for AI HART CHARM 0/ 4 to 20 mA with 3-wire AI Fused Injected Power Terminal Block.
RTD Input CHARM

Specifications for RTD Input CHARM
Sensor Types RTD input (Types listed in Table)
Sensor Configuration 2 wire, 3 wire, or 4 wire
Full Scale Signal Range See Table next page below
Accuracy See Table next page below
Resolution 24 bit A/D converter / Depends upon the sensor type
Sensor Excitation Current 0.5 mA in 2-wire and 4 wire configurations

0.25 mA in 3-wire
DC/50/60 Hz Common Mode Rejection 90dB typical
Isolation Each sensor galvanically isolated and factory tested

to 1000V DC
Open Sensor Detection Yes
CHARM Power Req. 22 mA max @ 24V DC
RTD, ohms Sensor Type Specifications

Sensor Operating 25° Reference Temperature
Resolution
Type Range Accuracy Drift
Pt100 -200 to 850°C ± 0.25°C ± 0.02°C/°C ~0.02°C
Pt200 -200 to 850°C ± 0.25°C ± 0.02°C/°C ~0.02°C
Pt500 -200 to 850°C ± 0.25°C ± 0.02°C/°C ~0.02°C
Pt1000 -200 to 260°C ± 0.25°C ± 0.02°C/°C ~0.01°C
Ni120 -80 to 260°C ± 0.15°C ± 0.01°C/°C ~0.01°C
Ni100 -80 to 260°C ± 0.20°C ± 0.01°C/°C ~0.01°C
Ni200 -80 to 260°C ± 0.20°C ± 0.01°C/°C ~0.01°C
Ni500 -80 to 260°C ± 0.20°C ± 0.01°C/°C ~0.01°C
Ni1000 -80 to 140°C ± 0.20°C ± 0.01°C/°C ~0.01°C
Cu10 -200 to 260°C ± 0.25°C ± 0.02°C/°C ~0.01°C
Resistance/User Defined* 0 to 2,000 Ω ± 0.25 Ω ± 0.03 Ω/°C ~0.031 Ω
* The Callendar-Van Dusen linearization equation can be used with user defined Pt RTDs.
Refer to Recommended I/O Practices in DeltaV Books online for usage information.
Simplified Circuit and Connection Diagrams for RTD CHARM.
Thermocouple/mV Input CHARM

Specifications for Thermocouple/mV Input CHARM
Sensor Types
Thermocouple B, E, J, K, N, R, S, T, uncharacterized
mV Low level voltage source (±20 mV, ±50 mV, and ±100 mV)
Full Scale Signal Range See Table next page
Accuracy See Table next page
Resolution 24-bit A/D converter / Depends upon the sensor type
Cold junction Compensation (CJC)

Accuracy ± 1.0°C
Range -40 to 85°C
DC/50/60 Hz Common Mode Rejection 90dB
Isolation Each sensor galvanically isolated and factory tested to

1000V DC
Open Sensor Detection Yes
Open Sensor Detection Current 45 nA
Sensor Type Specifications

Sensor 25° Reference Temperature Nominal Full Operating
Type Accuracy1 Drift Resolution Scale Range
B ± 0.8°C ± 0.06°C/ °C ~0.024°C 0 to 1820°C 250 to 1820°C
E ± 0.4°C ± 0.03°C/ °C ~0.018°C -270 to 1000°C -200 to 1000°C
J ± 0.6°C ± 0.04°C/ °C ~0.022°C -210 to 1200°C -210 to 1200°C
K ± 0.4°C ± 0.03°C/ °C ~0.025°C -270 to 1372°C -200 to 1372°C

N ± 0.6°C ± 0.04°C/ °C ~0.024°C -270 to 1300°C -200 to 1300°C
R ± 0.8°C ± 0.05°C/ °C ~0.028°C -50 to 1768°C -50 to 1768°C
S ± 0.8°C ± 0.05°C/ °C ~0.028°C -50 to 1768°C -50 to 1768°C
T ± 0.5°C ± 0.02°C/ °C ~0.01°C -270 to 400°C -250 to 400°C

± 100 mV 0.025 mV ± 0.002 mV/ °C ~0.0031mV -100 to 100 mV -100 to 100 mV
1
Total error is made up of the 25 C reference accuracy value, plus the CJC accuracy value, plus (I x R) open sensor error, plus the sensor accuracy value
Simplified Circuit and Connection Diagram for Thermocouple/mV CHARM with Thermocouple/mV
Terminal Block.
Analog Input 0-10V DC Isolated CHARM

Specifications for AI 0-10V DC Isolated CHARM
Sensor Types Voltage device
Full Scale Signal Range See Table below
Accuracy See Table below
Input Impedance 10 MΩ
Resolution 24-bit A/D converter / Refer to the following table
Common Mode Rejection 90dB at 50/60 Hz
Isolation Input channel galvanically isolated and factory tested

to 1000V DC
Isolated Input Voltage Sensor Type Specifications

Sensor Sensor 25° Reference Temperature Nominal
Type Range Accuracy1 Drift Resolution
0 to 5 V 0 to 5 V ±0.005 V ±0.0005 V/ °C 0.00008 V
0 to 10 V 0 to 10 V ±0.010 V ±0.001 V/ °C 0.00015 V
1 to 5 V 1 to 5 V ±0.005 V ±0.0005 V/ °C 0.00006 V
1V -1 to +1 V ±0.0025 V ±0.0002 V/ °C 0.00003 V
5V -5 to +5 V ±0.005 V ±0.0005 V/ °C 0.00015 V
10 V -10 to +10 V ±0.010 V ±0.001 V/ °C 0.00030 V
Simplified Circuit and Connection Diagram for Isolated Voltage CHARM.

Note: Installing a 250 Ω range resistor across terminals 3 and 4 converts a 4-20 mA field signal to 1-5V input signal.
Analog Output 4-20 mA HART CHARM

Specifications for AO 4-20 mA HART CHARM
Sensor Types 4 to 20 mA with or without HART
0 to 20 mA
Nominal Signal Range (Span) 4 to 20 mA, (0 to 20 mA option)
Full Signal Range 0 to 24 mA
Accuracy Over Temperature Range 0.25% of span (0 to 60°C)

0.5% of span (-40 to 70°C)
Resolution 16-bit D/A converter
Available Field Power 20 mA at 15V DC supply into 750 Ω load
Field Circuit Protection 24 mA Current Limiting Circuit

HART Support HART v7 pass-through for AMS

HART v7 variable and device status available to control
HART Data Update Rates Update rates are faster than every second dependent
on HART communication loading and device type
Simplified Circuit and Connection Diagram for HART AO CHARM 0/ 4 to 20 mA.
Discrete Input NAMUR CHARM

Specifications for DI NAMUR CHARM
Sensor Types NAMUR Sensors, Dry Contacts, Dry contact with
end of line resistance
Detection Level for On > 2.1 mA (<4 kΩ)
Detection Level for Off < 1.2 mA (>9 kΩ)
Channel Impedance 1.5 KΩ (approximate)
Wetting Voltage 12 Volts (± 5%)
Fault detection capable with NAMUR sensor or with an optional Guaranteed short circuit: <100 Ω
field resistor pack* as shown on Option 2 in diagram below Guaranteed good status: 400 Ω to 40 kΩ
(Option 1 in diagram below is not fault detection capable) Guaranteed open circuit: >75 kΩ
Configurable Channel Types:

Discrete Input Dry contact or discrete state sensor changing <2 Hz
Pulse Count Pulse train 0.1 Hz to 10 KHz, 50 µsec min pulse width
*VS6904 End of Line Resistance Module can be used for option 2, see DeltaV SIS Conditioning Components PDS for more info.
Simplified Circuit and Connection Diagram for DI NAMUR CHARM.
Discrete Input 24 V DC low-side sense (dry contact) CHARM

Specifications for DI 24 V DC low-side sense (dry contact) CHARM
Sensor Types 24V DC Dry Contacts
Detection Level for On >2.25 mA (<5.3 kΩ)
Detection Level for Off <1.75 mA (>8.2 kΩ)
Channel Impedance 4.8 KΩ
Wetting Voltage 22.5Volts (± 5%), current limited to 12.5 mA nominal
Fault detection capable with an optional field resistor pack* as Guaranteed short circuit: <100 Ω
shown on Option 1 in diagram below (Without resistor pack Guaranteed good status: 400 Ω to 40 kΩ
fault detection is not possible) Guaranteed open circuit: > 75 kΩ

Field Circuit Protection 12.5 mA Current Limiting Circuit
*VS6904 End of Line Resistance Module can be used for option 1, see DeltaV SIS Conditioning Components PDS for more info.
Simplified Circuit and Connection Diagram for DI 24V DC low-side sense CHARM.
Discrete Input 24V DC Isolated CHARM

Specifications for DI 24V DC Isolated CHARM
Detection Level for On >10V DC
Detection Level for Off <5V DC
Wetting Current 6 mA @ 24V DC
Input Impedance 4 KΩ (approximately)
Isolation Galvanically isolated and factory tested to 1000V DC

Field Circuit Protection Recommend External Fuse at power source
Simplified Circuit and Connection Diagrams for DI 24V DC Isolated CHARM.
Simplified Circuit and Connection Diagrams for DI 24 V DC Isolated CHARM with 3-wire DI Fused Injected-Power Terminal Block.
Discrete Output 24V DC High-Side CHARM

Specifications for DO 24V DC High-Side CHARM
Device Type 24V DC Solenoid coils
On State Output Rating 100 mA continuous @ 24V DC
Off-state Leakage Current 1 mA maximum
Line Fault Detection Guaranteed short circuit: <50 Ω load

Guaranteed good status: 240 Ω to 10 kΩ load
Guaranteed open circuit: >20 kΩ load
Configurable Output Behavior Momentary Output

Continuous Pulse Output
Line fault testing
Line Fault Test Timing 200 µsec

CHARM Power Req. 116 mA max @ 24 V DC - Standard Terminal Block
24 mA max @ 24 V DC - Relay Output Terminal Block
CHARM Heat Dissipation 0.44 W - Standard Terminal Block
0.61 W - Relay Output Terminal Block
Simplified Circuit and Connection Diagram for DO 24V DC High Side CHARM.
Simplified Circuit and Connection Diagram for DO 24V DC High Side CHARM with
CHARM Relay Output Terminal Block.
Discrete Output 100mA Energy Limited CHARM

Specifications for DO 100 mA Energy Limited CHARM
Device Type 24V DC Solenoid coils
On State Output Rating 100 mA continuous @ 24V DC
Off-state Leakage Current 1 mA maximum
Line Fault Detection Guaranteed short circuit: <50 Ω load

Guaranteed good status: 240 Ω to 10 kΩ load
Guaranteed open circuit: >20 kΩ load

Line fault testing
Line Fault Test Timing 200 µsec

Simplified Circuit and Connection Diagram for DO 100 mA Energy limited CHARM.
Discrete Output 24V DC Isolated CHARM

Specifications for DO 24V DC Isolated CHARM
Device Type 24V DC Inductive Load
Output Range 4V DC to 32V DC
Output Rating 1.0 A continuous

(2 A inrush for <100 ms)
Off State Leakage Current 1 mA maximum

Isolation The output channel is galvanically isolated and factory tested
to 1000V DC.
Field Circuit Protection 4 A Current Limiting Circuit (Short Circuit)
with thermal shutoff, automatic reset
Recommend external fuse at power source
Simplified Circuit and Connection Diagrams for DO 24V DC Isolated CHARM.
Simplified Circuit and Connection Diagrams for DO 24V DC Isolated

CHARM with Fused Injected-Power Terminal Block.
24V DC Power CHARM

Specifications for 24V DC Power CHARM
Device Type 24V DC Power output
Status Read Back Level for Power Good >10V DC
Status Read Back Level for Power Bad <5V DC
Isolation Status read back circuitry is optically isolated and

factory tested to 1000V DC. Output power has
no isolation from the injection point.
Field Circuit Protection 2 Amp fuse located in Fused-Injected-Power Terminal Block
Injected Power Req. 1.01 Amps max @ 24V DC
Simplified Circuit and Connection Diagrams for 24V DC Power CHARM

with Fused Injected-Power Terminal Block.
Simplified Circuit and Connection Diagrams for 24V DC Power Simplified Circuit and Connection Diagrams for 24V DC Power
CHARM with Fused Injected-Power Terminal Block – CHARM with Fused Injected-Power Terminal Block - powering 4-wire
powering 3-wire HART Transmitter connected to HART Transmitter connected to AI HART CHARM 0/ 4 to 20 mA.
AI HART CHARM 0/ 4 to 20 mA.
Discrete Input 120V AC Isolated CHARM

Specifications for DI 120V AC Isolated CHARM
Detection Level for On >84V AC
Detection Level for Off <34V AC
Wetting Current 2 mA at 120V AC
Maximum Input Voltage 130V AC
Frequency 50/60 Hz
Isolation Each channel is optically isolated from the system at 250V AC

Pulse Count Pulse train 0.1 Hz to 10 Hz
Simplified Circuit and Connection Diagrams for DI 120V AC Isolated CHARM.
Simplified Circuit and Connection Diagrams for DI 120V AC Isolated CHARM with 3-wire DI Fused-Injected-Power Terminal Block.
Discrete Input 120V AC Isolated Plus CHARM

Specifications for DI 120V AC Isolated Plus CHARM
Frequency 50/60 Hz

Simplified Circuit and Connection Diagrams for DI 120V AC Isolated Plus CHARM.
Simplified Circuit and Connection Diagrams for DI 120V AC Isolated Plus CHARM with 3-wire DI Fused-Injected-Power Terminal Block.
Discrete Input 230V AC Isolated CHARM

Specifications for DI 230V AC Isolated CHARM
Frequency 50/60 Hz

Simplified Circuit and Connection Diagrams for DI 230V AC Isolated CHARM.
Simplified Circuit and Connection Diagrams for DI 230V AC Isolated CHARM with 3-wire DI Fused-Injected-Power Terminal Block.
Discrete Output V AC Isolated CHARM

Specifications for DO V AC Isolated CHARM
Sensor Types V AC Inductive load
Output Range 20 to 250V AC
Output Rating 0.5 A continuous

(10 A inrush for <20 ms, 2.5 A inrush for <100 ms)
Off State Leakage Current 2 mA maximum at 120V AC
4 mA maximum at 230V AC
Field Circuit Protection Field wiring disconnect

Recommend external fuse at power source
Simplified Circuit and Connection Diagrams for DO V AC Isolated CHARM.
Simplified Circuit and Connection Diagrams for DO V AC Isolated CHARM

with Fused-Injected-Power Terminal Block.
ASCO Numatics 580 CHARM Node

Specifications for ASCO Numatics 580 CHARM Node
Bus Power 6.3V DC at 100mA
Valve Power 24V DC at 1.07A
Power and Bus Connector A-Coded 5 Pin M12 Male
LEDs Module Status and Network Status
Operating Temperature Range -10 to 115°F (-23 to 46°C)
Operating Humidity 95% Relative Humidity, Non-condensing
Vibration Shock EC 60068-2-27, IEC 60068-2-6
Moisture IP65 Certified
Maximum Valve Solenoid Outputs 48
Diagnostics Power, short, open load conditions are monitored
More information: http://www.asco.com/580charm*
*For hazardous area installations, please refer to installation instructions from ASCO.
580 CHARM Node.
Connection to DeltaV Electronic Marshalling.
System Compatibility IEC-Ex
IEC60079-0
CHARM I/O hardware requires:
IEC60079-15
SD Plus controllers with DeltaV v11.3.1 or later software
Marine Certifications: IACS E10
SX controllers with DeltaV v11.3.1 or later software
ABS Certificate of Design Assessment
SQ controllers with DeltaV v11.3.1 or later software
DNV-GL Marine Certificate
MD Plus controllers with DeltaV v14.3 or later software
Wurldtech:
MQ controllers with DeltaV v14.3 or later software
CIOC: Achilles Communications Certification
MX controllers with DeltaV v14.3 or later software
Level 1 (v.13.3.1)
PK controllers with DeltaV v14.3 or later software
Pending: CIOC2: Achilles Communications Certification
When assigning CHARMs to MD Plus and SD Plus controllers, Level 2 (v.14.3.1)
make sure to evaluate the Time Utilization Chart on the
controller in DeltaV Diagnostics to ensure the additional Hazardous Area/Location
communication load can be handled by the controller.
DeltaV Electronic Marshalling solutions can be installed
S-series and M-series controllers can be installed on the same
and used based on the following Standards: (see actual
DeltaV Area Control Network in v11 and beyond. PK controllers
certificates for exact product markings for each product)
can be installed on the same DeltaV Area Control network in
v14.3 and beyond. FM (USA)
Control modules can be assigned to any controller and inter- Installation and Field Circuits:
controller references are fully supported between different
Class I, Division 2, Groups A, B, C, D, T4
types of controllers.
cFM (Canada)
Certifications Installation and Field Circuits:
Class I, Division 2, Groups A, B, C, D, T4

The following certifications are available for DeltaV
Electronic Marshalling: ATEX
Installation and Field Circuits:

CE
II 3G Ex nA IIC T4 Gc
EMC - EN 61326-1
II 3G Ex nA [ic] IIC T4 Gc
FM
II 3G Ex nA nC IIC T4 Gc
FM 3600
IEC-Ex
FM 3611
Installation and Field Circuits:
CSA
II 3G Ex nA IIC T4 Gc
CSA C22.2 No. 213-M1987
II 3G Ex nA ic IIC T4 Gc
CSA C22.2 No. 61010-1
II 3G Ex nA nC IIC T4 Gc
ATEX
EN60079-0 Class 1 Division 2 Installation Instructions CHARM Subsystem 12P5401

Class 1 Division 2 Installation Instructions DeltaV S-Series 12P5402
EN60079-15 Zone 2 Installation Instructions CHARM Subsystem 12P5403
Zone 2 Installation Instructions DeltaV S-Series 12P5404
Additional Field Circuit Certification Information

Class I
Zone 2 Ex nL Zone 2 Ex ic Zone 2 Ex nA
CHARM Type Description Division II Non
Certified Certified Certified
Incendive
DI NAMUR    
DI 24V DC Low-Side Sense (Dry Contact)    
DI 24V DC Isolated — — — 
DO 24V DC High-Side — — — 
DO 24V DC 100mA Energy Limited    
DO 24V DC Isolated — — — 
24V DC Power — — — 
AI 4-20 mA HART    
Thermocouple/mV Input    
RTD Input    
AI 0-10V DC Isolated    
AO 4-20 mA HART    
DI 120V AC Isolated — — — —
DI 120V AC Isolated Plus — — — —
DI 230V AC Isolated — — — —
DO V AC Isolated — — — —
Class I
Zone 2 Ex nL Zone 2 Ex ic Zone 2 Ex nA
CHARMs and Terminal Block Assembly Description Division II Non
Certified Certified Certified
Incendive
DO 24V DC High-Side CHARM with
— — — 
Relay Output Terminal Block
Thermocouple/mV Input CHARM with
   
Thermocouple/mV Terminal Block
24V DC Power CHARM with
— — — 
Fused-Injected-Power Terminal Block
AI 4-20 mA HART with
— — — 
3-wire AI Fused Injected Power Terminal Block
— Stands for: Not Applicable;  Stands for : Certification is in place.
Ordering Information
CHARM I/O Cards and Carrier
Description Model Number

Redundant CIOC2 with Copper Ethernet, includes redundant pair of CHARM I/O Card 2, CHARM I/O Carrier SE6505T01
with Screw Terminals, Copper I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC2 with fiber optics Ethernet, includes redundant pair of CHARM I/O Card 2, CHARM I/O Carrier SE6505T02
with Screw Terminals, Fiberoptic I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC with Copper Ethernet, includes redundant pair of CHARM I/O Cards, CHARM I/O Carrier with SE6501T01
Screw Terminals, Copper I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC with fiber optics Ethernet, includes redundant pair of CHARM I/O Cards, CHARM I/O Carrier SE6501T02
with Screw Terminals, Fiberoptic I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC Carrier Assembly with Copper Ethernet, includes CHARM I/O Carrier with Screw Terminals, SE6501T05
Copper I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC Carrier Assembly with fiber optics Ethernet, includes CHARM I/O Carrier with Screw Terminals, SE6501T06
Fiberoptic I/O Ports, a Baseplate Identifier and a Baseplate Separation Wall
Redundant CIOC2, includes 2 CHARMs I/O Card 2, (Order these with standard cabinets) SE6504
Redundant CIOC, includes 2 CHARMs I/O Cards, (Order these with standard cabinets) SE6502
CHARM Baseplates Assemblies

CHARMs Baseplate Assembly, includes CHARMs Baseplate, CHARM Address Terminal Block with Screw SE4601T07
Terminals,12 Standard CHARM Terminal Blocks and a Baseplate Identifier
CHARMs Baseplate Assembly with 3-wire DI Fused Fused-Injected-Power, includes CHARMS Baseplate, SE4601T09
CHARM Address Terminal Block with Screw Terminals,12 3-wire DI Fused-Injected-Power CHARM Terminal
Blocks and a Baseplate Identifier
CHARMs Baseplate Assembly with Fused-Injected Field Power, includes CHARMS Baseplate, SE4601T08
CHARM Address Terminal Block with Screw Terminals,12 Fused-Injected-Power CHARM
Terminal Blocks and a Baseplate Identifier
CHARMs Baseplate Assembly with Relay Output, includes CHARMS Baseplate, CHARM Address Terminal SE4601T05
Block with Screw Terminals,12 Relay Output CHARM Terminal Blocks and a Baseplate Identifier
CHARM I/O Baseplate Address Plugs

CHARMs Addressing Plugs, includes Address Plugs 1 through 8 SE4602
CHARMs Addressing Plugs, includes Address Plugs 1 through 4 SE4613
Each vertical DIN rail requires a DIN Rail stop to lock baseplates in position. Order VE4054DRS, which is a box of 5.
CHARM I/O Baseplate Extender and Terminator

CHARMs Baseplate Extender with Cable Connectors, Top (Male) SE4603T05
includes a Baseplate Identifier and a Baseplate Separation Wall
CHARMs Baseplate Extender with Cable Connectors, Bottom (Female) SE4603T06
CHARMs Baseplate Terminator, Top (Male) SE4604T03
CHARMs Baseplate Terminator, Bottom (Female) SE4604T04
CHARM I/O Baseplate Extender Cables

CHARMs Baseplate Cables, includes two 0.5 m cables SE4605T02
CHARMs Baseplate Cables, includes two 1 m cables SE4605T03
CHARMs Baseplate Cables, includes two 2 m cables SE4605T04

Each vertical DIN rail requires a DIN Rail stop to lock baseplates in position. Order VE4054DRS, which is a box of 5.
Low Voltage Instrumentation CHARMs

DI NAMUR SE4301T01
DI 24V DC Low-Side Sense (Dry Contact) SE4301T02
DI 24V DC Isolated SE4301T07
DO 24V DC High-Side SE4302T01
DO 24V DC Isolated SE4302T02
DO 24V DC 100mA Energy Limited SE4302T04
24V DC Power SE4302T05*

AI 4-20 mA HART SE4303T01
Thermocouple/mV Input SE4303T02
RTD Input SE4303T03
AI 0-10V DC Isolated SE4303T04
AO 4-20 mA HART SE4304T01
High Voltage Instrumentation CHARMs

DI 120V AC Isolated SE4301T03
DI 120V AC Isolated Plus SE4301T05**
DI 230V AC Isolated SE4301T04
DO V AC Isolated SE4302T03
Low Voltage Instrumentation CHARMs and Terminal Block Assemblies

DO 24V DC High-Side CHARM with Relay Output Terminal Block SE4302T51
Thermocouple/mV Input CHARM with Thermocouple/mV Terminal Block SE4303T52
24V DC Power CHARM with Fused-Injected-Power Terminal Block SE4302T55*
* 24V DC Power CHARM requires DeltaV v12.3 or later software to be able to configure and use the diagnostic Information.
** The DI 120V AC Isolated Plus CHARM requires a HotFix to be used with DeltaV v11.3.1 and v12.3.1.
Additional Ordering Information for Protection Cover and Terminal Blocks

Protection Cover (fits all terminal blocks)

CHARM Protection Cover; Package of 12 SE6103
Terminal Blocks

Standard CHARM Terminal Block SE4501
3-wire DI Fused-Injected-Power Terminal Block SE4512
Fused-Injected-Power Terminal Block SE4502
Relay Output Terminal Block SE4503
Thermocouple/mV Terminal Block SE4504
3-wire AI Fused Injected Power Terminal Block SE4511
CHARM I/O Labeling and Spare part ordering Information

CHARM I/O Labeling and Spare Parts

Channel Identifier Labels for CHARM Baseplates; Package of 8 SE4606T02
Charm Baseplate Identifier; Package of 9 SE4606T03
Power Terminal Plug for CHARM I/O Carrier KJ4005X1-BF1
250V 2A Fuse for Fused Terminal Block; Box of 20 KJ4010X1-BC1
I/O Port Switch Module; Copper; for CIOC Carriers KL1601X1-BA1
I/O Port Switch Module; Fiber; for CIOC Carriers KL1602X1-BA1*

* Fiberoptic Ethernet I/O Ports are not cascadeable.
ASCO Numatics Series 580 CHARM node

ASCO Numatics Series 580 CHARM node parts
ASCO Part
Description
Number
580 CHARM node Contact ASCO*
580 CHARM Power and Communication Cable Set Contact ASCO*

2 Cables, 1.5 M Length, with M12 and sub-D connectors
* Requires hotfix for DeltaV v11.3.1, v12.3.1, and v13.3. Sold directly from ASCO, please see more detail at http://www.asco.com/580CHARM .
Related Products Prerequisites

DeltaV Electronic Marshalling with Distributed CHARMs DeltaV Electronic Marshalling hardware requires DeltaV v11.3.1
or later software. Assigning CHARMs to MD Plus, MQ, MX, and
PK controllers is supported in DeltaV v14.3 and later, but is
not supported on M-series Controller Interfaces to PROVOX
and RS3.
CHARM I/O Card 2 (CIOC2) requires DeltaV v14.3 or l

ater software.
Electronic Marshalling requires use of DeltaV Smart Switches

between controllers and CIOCs, please refer to Network
Considerations for M-series with Electronic Marshalling White
Paper when adding Electronic Marshalling to M-series systems.
Emerson
North America, Latin America:
©2019, Emerson. All rights reserved.
+1 800 833 8314 or
+1 512 832 3774 The Emerson logo is a trademark and service mark of Emerson Electric Co. The DeltaV logo is
a mark of one of the Emerson family of companies. All other marks are the property of their
Asia Pacific: respective owners.
+65 6777 8211 The contents of this publication are presented for informational purposes only, and while
diligent efforts were made to ensure their accuracy, they are not to be construed as warranties
Europe, Middle East: or guarantees, express or implied, regarding the products or services described herein or their
+41 41 768 6111 use or applicability. All sales are governed by our terms and conditions, which are available on
request. We reserve the right to modify or improve the designs or specifications of our products
www.emerson.com/deltav at any time without notice.

DeltaV CHARM

Uploaded by

Copyright:

Available Formats

DeltaV CHARM

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DeltaV CHARM

Uploaded by

Copyright:

Available Formats

DeltaV Distributed Control System Product Data Sheet

DeltaV Electronic Marshalling

Single channel granularity

Reduces installed cost of system

Fully redundant architecture

Field-mounted capable hardware

Plug and play I/O

The DeltaV CHARM I/O Card (CIOC) with CHARMs.

Introduction Single channel granularity: The CHARM I/O architecture

Fully redundant communications: The CIOC architecture is Product Description

 Labeling features for baseplate and channel identification.

CHARM and Terminal Block.

Field power is provided through a redundant 24V DC bus to

 DI 120V AC Isolated Plus

CHARM Latch mechanism.

I/O Terminal Block Options  48V DC at 0.4 A switching current

 110V DC at 0.2 A switching current

CHARM Keying Posts ASCO Numatics 580 CHARM Node

 Redundant communications and power connections to

 Eliminates the need for additional dedicated networks like

 Expands the Electronic Marshalling I/O offering to include

 Reduces programming and commissioning time dramatically.

CHARM standard Terminal block.

The keying mechanism consists of two keying posts that rotate

ASCO Numatics 580 CHARM Node.

Storage Temperature -40 to 85°C (-40 to 185°F)

Relative Humidity 5 to 95% , non-condensing

Airborne Contaminants ISA-S71.04-1985 Airborne Contaminants Class G3 Conformal coating

Shock 10 g ½-sine wave for 11 ms

Vibration 1 mm peak-to-peak from 2 to 13.2 Hz, 0.7 g from 13.2 to 150 Hz

CHARM I/O Card and Carrier.

CIOC Carrier Ethernet Communication Modules

CHARM Baseplate with Identifier, CHARMs and Label Plates.

CHARM Baseplate Terminator, Top.

DI 120V AC Isolated Plus CHARMs.

CHARM Baseplate Terminator, Bottom.

CHARM Baseplate Extender, Top.

CHARM Standard Terminal Block.

CHARM Baseplate Extender, Bottom.

CHARM Fused Injected-Power Terminal Block. Address Plug.

Address Plug Terminal Block.

CHARM I/O Card hardware

Input Power (Redundant) +24V DC ±10% at 12 A maximum

Mounting DIN rail Latch to vertical T-type rail

Number of I/O Clients 4 (Controllers)

Number of CIOCs per Controller 16

Number of CIOCs per System 300

I/O Update Rates 50ms, 100ms, 250ms, 500ms

CIOC Power (24 V DC) 0.28 A per redundant CIOC node

CIOC output to CHARMS 6.3V DC redundant power, at 3.25 A maximum*

Fuse Protection (internal) Internal Non-replaceable Fuse

Mounting 2-wide CHARM I/O Carrier

Communication Redundant Ethernet connections through CHARM I/O Carrier

Network Addressing Auto Assigned during commissioning

Red – Error Indicates an error condition

Green – Active/Standby Indicates operating mode of each CIOC

Yellow Flashing – Pri./Sec. CN Indicates valid control network communication

Number of Base Plates per CIOC 8

Addressing One Address Plug (1 through 8)

Terminal Blocks  Standard Terminal Block

Single channel granularity

Reduces installed cost of system

Fully redundant architecture

Field-mounted capable hardware

Plug and play I/O

Labeling features for baseplate and channel identification.

DI 120V AC Isolated Plus

I/O Terminal Block Options 48V DC at 0.4 A switching current

110V DC at 0.2 A switching current

Redundant communications and power connections to

Eliminates the need for additional dedicated networks like

Expands the Electronic Marshalling I/O offering to include

Reduces programming and commissioning time dramatically.

Terminal Blocks Standard Terminal Block

Field Circuit Protection 30 mA Current Limiting circuit