Scribd
Upload
2K views4 pages

Weld Design Spreadsheet

This document summarizes the design of a fillet weld for a concentric connection based on AISC 360-16 Chapter J. It provides the design input data including a 150 kN applied load, weld electrode type, base metal properties, weld sizes, and lengths. It calculates the effective weld lengths, weld strengths in shear and parallel to the load, and the total weld shear strength of 245.36 kN. It indicates the weld capacity exceeds the applied load of 150 kN and notes the weld strengths must be compared to the connected part strengths.

Uploaded by

Ali Akbar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
2K views4 pages

Weld Design Spreadsheet

This document summarizes the design of a fillet weld for a concentric connection based on AISC 360-16 Chapter J. It provides the design input data including a 150 kN applied load, weld electrode type, base metal properties, weld sizes, and lengths. It calculates the effective weld lengths, weld strengths in shear and parallel to the load, and the total weld shear strength of 245.36 kN. It indicates the weld capacity exceeds the applied load of 150 kN and notes the weld strengths must be compared to the connected part strengths.

Uploaded by

Ali Akbar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

FILLET WELD CAPACITY DESIGN (CONCENTRIC CONNECTION)

Based on AISC 360-16 Chapter J


Client: Designed By: Ali Akbar Shaikhzadeh Date: 20-Jan-20
Job Name: Verified By: Revision: 35%

DESIGN INPUT DATA

APPLIED FACTORED LOAD, PU 150 kN

WELD ELECTRODE E70


BASE METAL YEILD STRENGTH, Fy 248 MPa

TOTAL LENGTH OF WELD PARALLEL TO LOAD 200 mm

TOTAL LENGTH OF WELD TRANSVERSE TO LOAD 100 mm

ANGLE OF PARALLEL WELD WITH APPLIED LOAD, q 0 deg.

WELD SIZE, w 5 mm

THICKNESS OF THINNER CONNECTED PARTS 10 mm

WELD SIZE CONTROL

wmin 5 mm Minimum weld size


wmax 8 mm Maximum weld size
wprovided O.K. Control of weld size
Lmin 20 mm Minimum length of weld
Lmax 500 mm Maximum length of weld
Lprovided O.K. Control of longitudinal weld length

EFFECTIVE WELD LENGTH

1.00 Reduction factor for weld lengths greater than 100 times weld size
Leff, parallel 200 Effective length of parallel weld
Leff, transverse 100 Effective length of transverse weld

WELD STRENGTH

FEXX 482 MPa Electrode ultimate tensile stress


Fnw = 0.6FEXX 289.20 MPa Electrode ultimate shear stress
Fnw = 0.6FEXX (1 + 0.5 sin1.5q) 289.20 MPa Electrode ultimate shear stress modified for angle q
Rwl 204.46 kN Parallel weld strength (calculated with FNW modified for q)
Rwt 102.23 kN Transverse weld strength (calculated with FNW not modified for q)
fRn 245.36 kN Total weld shear strength J2-10a & J2-10b

Pu O.K. Control of weld capacity with applied load


IMPORTANT NOTE:
THE WELD STRENGTH MUST ALSO BE COMPARED WITH CONNECTED PARTS YEILD AND FRACTURE STRENGTHS.
DESIGN (CONCENTRIC CONNECTION)
on AISC 360-16 Chapter J
20-Jan-20
35%
Version 1.0

Table J2.4

J2b. (b)

J2b. (c)

J2-1

J2-10a & J2-10b

You might also like