Scribd
Upload
72 views2 pages

Calcul Lant

This document provides information and calculations for selecting roller chains according to ISO 10823. It examines a case using a 20.2 kW input power, 9.09 1/min input speed, 50 tooth driver sprocket, 58 tooth driven sprocket, and 1.4m approximate center distance. The results show 6 suitable chain types between 32B-48B with 3 strands, along with their speeds, maximum center distances, and recommended lubrication ranges. It also lists intermediate calculation factors and viscosity classes for lubricating oils based on ambient temperature.

Uploaded by

Diana Maria Cozma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
72 views2 pages

Calcul Lant

This document provides information and calculations for selecting roller chains according to ISO 10823. It examines a case using a 20.2 kW input power, 9.09 1/min input speed, 50 tooth driver sprocket, 58 tooth driven sprocket, and 1.4m approximate center distance. The results show 6 suitable chain types between 32B-48B with 3 strands, along with their speeds, maximum center distances, and recommended lubrication ranges. It also lists intermediate calculation factors and viscosity classes for lubricating oils based on ambient temperature.

Uploaded by

Diana Maria Cozma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 2

Transilvania University of Brasov

Program : MDESIGN User : Customer:

Module version: 15.0 Date : 17.11.2019 Project:

Roller Chains ISO 10823

The calculation module is based upon DIN ISO 10823 "Guidance on the selection of roller chain drives". This international
standard refers to roller chains and chain wheels in accordance with ISO 606.

The selection procedures and the chain ratings in ISO 10823 provide for roller chain drives with a life expectancy of approximately
15,000 hours under the following conditions:

- Utilisation of a suitable method of lubrication (as shown on the results page),


- Use of a lubricating oil with a suitable viscosity class (table can be selected to be shown on results page)
- Centre distance measures between 30 and 50 times the chain pitch,
- Arc of contact of not less than 120° on the drive sprocket,
- Usage of chain adjustment.

In ISO 10823 it is specifically recommended to consult with the supplier of the equipment intended to be used to ensure its
suitability.

Input data:

Roller Chains ISO 10823

Method of calculation Calculation of all suitable chains


Type of roller chain to be used European Type (DIN 8187)
Input power P = 20,2 kW
Input speed n1 = 9,09 1/min
Number of teeth on driver sprocket z1 = 50
Number of teeth on driven sprocket z2 = 58
Drive ratio i = 1,15
Approximate centre distance a0 = 1400 mm
Define minimum and maximum centre distance? No

Characteristics of driver machine Moderate shocks


Characteristics of driven machine Smooth running

Application factor to allow for the operating conditions f1 = 1,3


Factor for number of teeth on drive sprocket f2 = 0,45
Corrected power Pc = 11,817 kW
Allow adjustment of factors f1 and f2? No

Display intermediate results on output page? Yes


Display listing of viscosity classes of lubricating oil on output page? Yes

Results:

General results
Chain Strands Pitchp LinksX SpeedV Max. Lubrication
type mm m/s center range
distancea
mm
48B 1 76,2 92 0,577 1444,456 2

LANT-CUREA_LANT.mdp 11/17/2019 07:24:21 Page 1/2


Transilvania University of Brasov
Program : MDESIGN User : Customer:

Module version: 15.0 Date : 17.11.2019 Project:

Roller Chains ISO 10823

40B 2 63,5 100 0,481 1458,222 2


48B 2 76,2 92 0,577 1444,456 2
32B 3 50,8 110 0,385 1420,921 2
40B 3 63,5 100 0,481 1458,222 2
48B 3 76,2 92 0,577 1444,456 2

Lubrication range 1: Oil supply by means of oil can or brush, applied manually at frequent intervals
Lubrication range 2: Drip-feed lubrication
Lubrication range 3: Oil bath or disc lubrication
Lubrication range 4: Forced-feed lubrication with filter and, if necessary, an oil cooler

Viscosity classes of chain drive lubricating oils


Ambient temperature Viscosity class of oil
-5°C < T < +5°C VG 68 (SAE 20)
+5°C < T < +25°C VG 100 (SAE 30)
+25°C < T < +45°C VG 150 (SAE 40)
+45°C < T < +70°C VG 220 (SAE 50)

List of intermediate results


Chain Strand Max . Utilisat Factor Links Factor (X - z1)/
type s Pc ion f3 (calculated)X0 f4 (z2 - z1)
for n1 %
kW
48B 1 11,9 99,3 1,62 90,8 0,249 5,25
1 3 42
40B 2 13,6 86,88 1,62 98,1 0,249 6,25
1 7 61
48B 2 20,8 56,73 1,62 90,8 0,249 5,25
3 1 3 42
32B 3 11,8 99,46 1,62 109,1 0,249 7,50
8 1 8 74
40B 3 19,4 60,81 1,62 98,1 0,249 6,25
3 1 7 61
48B 3 29,7 39,69 1,62 90,8 0,249 5,25
7 1 3 42

Note:

Ensure that the lubricating oil is free from contaminants, particularly abrasive particles!

LANT-CUREA_LANT.mdp 11/17/2019 07:24:21 Page 2/2

You might also like