Order No.

MTV0110238C3

Colour Television
TX-25P80T
MX-10 Chassis

Specification
Power Source AC Auto 110-240 V, 50/60 Hz Video 38.0 MHz
Power Consumption 138 W Sound 31.5 MHz (D,K) / 32.5 MHz (B,G)
Standby condition : 0.8 W 32.0 MHz (I) / 32.5 MHz (M)
Aerial Terminal Impedance : 75Ω, Coaxial type
Colour 33.57 MHz (PAL) /
Tuning System Frequency Synthesizer
Auto Search Tuning 33.6 MHz (SECAM)
Pos : 100 Positions 34.42 MHz (NTSC) /

Receiving System 17 Systems 33.75 MHz (SECAM)

Receiving Channels Regular TV Receiving Stereo Sound System QUADRA STEREO / TEXT

VHF BAND 2-12 (PAL/SECAM B, K1) Video/Audio/Terminals

0-12 (PAL B AUST.) IN S-Video Y:1.0Vp-p 75Ω
1-9 (PAL B N.Z.) AV 1, 2, 3 DVD IN S-Video C:0.3Vp-p 75Ω
1-12 (PAL/SECAM D) Y/PB/PR (Phone type) Y:1.0Vp-p 75Ω PB,
1-12 (NTSC M Japan) PR:0.7Vp-p 75Ω Video 1.0Vp-p
2-13 (NTSC M U.S.A.) 75Ω Audio Approx. 400mV 47KΩ
UHF BAND
Video 1,0Vp-p 75Ω
21-69 (PAL G,H,I/SECAM G,K,K1)
Monitor Out Audio Approx. 400mV 47KΩ
28-69 (PAL B AUST.)
13-57 (PAL D,K) High Voltage 31.0 (+0.7, -1.5kV) at zero beam
CATV 13-62 (NTSC M Japan) current
14-69 (NTSC M U.S.A.) Picture Tube A60LUQ085X Type 25 (60 cm)
S1-S20 (OSCAR) Measured diagonally, 104°
1-125 (U.S.A. CATV) deflection
C13-C49 (JAPAN) Audio Output 16 W speaker
S21-S41 (HYPER)
Dimensions (WxDxH) 634 mm x 471 mm x 534 mm
Z1-Z37 (CHINA)
Weight (Mass) 37 kg (Net)
Intermediate Frequency
Accessories Supplied
Remote Control Transmitter 1. R6(AA) Battery x 2

© 2001 Matsushita Electric Industrial Co., Ltd. All

rights reserved. Unauthorized copying and
distribution is a violation of law.
TX-25P80T

4 MARKET MODE FUNCTION

Outline:
MPU controls the functions switching for each ICs through IIC bus in this chassis. The following setting and adjustment can be
adjusted by remote control in Market Mode.
1. Selection of Market Mode
Adjust the VOLUME “zero” and set OFF TIMER Button to 30 min. Then, simultaneously press the RECALL Button on the
remote control and the VOLUME DOWN button - the TV set.
2. Selection of CHK Mode
Cursor moves each CHK Mode by pressing “1” or “2” of 10 key button on the remote control.

1. Option Code Setting Mode (CHK 1)

If the memory IC (IC1102) is replaced, option code should be re-memorized. Option code can be changed by pressing Volume
“+” or “-” button. To memorize, press “0” of the 10 key button.
Display Adj. Range
COLOUR SYSTEM 0~6
MX 10A OFF / ON
C4 BIT OFF / ON
NOISE MUTE OFF / ON
SPEED OFF / ON
VCR / GAME OFF / ON
YUV OFF / ON
AV3 OFF / ON
STEREO OFF / ON
GEO 0~2
SASO 0~2
TEXT OFF / ON
PANA DISPLAY OFF / ON
SOUND SYS 0~5

2. VCJ Adjustment Mode

To change the screen (item) in CHK mode, press “3” or “4” of the 10 key button. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
SUB COLOUR 00H ~ 3FH
COLOUR 0 ~ 63
RF AGC 00H ~ FFH
SECAM B-Y 00H ~ 0FH
SECAM R-Y 00H ~ 0FH
B-Y 00H ~ 0FH
R-Y 00H ~ 0FH
SUB TEXT CONT 00H ~ 3FH
SHARPNESS 0 ~ 63
SUB Y CONT 00H ~ 3FH
CONT 0 ~ 63
SUB BRIGHT 00H ~ FFH
BRIGHT 0 ~ 63
SUB NTS-TINT 00H ~ 3FH

6
 TX-25P80T

3. Pincushion Adjustment Mode

To change the screen (item) in CHK mode, press “3” or “4” of the 10 key buttons. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
PARABOLA 00H ~ 3FH
60 V-HEIGHT 00H ~ 3FH
50 V-HEIGHT 00H ~ 3FH
SUB GEO 00H ~ 3FH
GEOMAGNETIC -9 AUTO 9
V CENTER 00H ~ 07H
50Hz CENTER 00H ~ 1FH
EW-CORNER 1 00H ~ 0FH
TRAPEZOID 00H ~ 3FH
V-LINEAR 00H ~ 3FH
60 VS CORRECT 00H ~ 3FH
50 VS CORRECT 00H ~ 3FH
H-WIDTH 00H ~ 3FH

Note : Picture will be changed to one horizontal line by pressing “5” of the 10 key button in the remote control. (1 - 5).

4. White Balance Adjustment Mode

To change the screen (item) in CHK mode, press “3” or “4” of the 10 key buttons. Then the Date and Level changes by pressing
Volume “+” or “-” button.
Display Adj. Range
B. DR 00H ~ FFH
G. DR 00H ~ FFH
SUB.BR 00H ~ FFH
BRIGHT 0 ~ 63
B - CUT 00H ~ FFH
G - CUT 00H ~ FFH
R - CUT 00H ~ FFH

7
TX-25P80T

5 ADJUSTMENT PROCEDURE
5.1. B VOLTAGE
Item/Preparation Adjustment Procedure
1. Operate the TV set. 1. Confirm that the indicated test points for the
specified voltage:
TPA 140 : 141±2V
2. Set controls : (MARKET MODE CHK 2) TPA 12 : 12±1.0V
Bright ............. Minimum TPA 9 : 9±1V
Contrast ......... Minimum
TPA 5 & TPA 32 : 5±1V
Volume ............. Minimum
TPA 220 : 220±15V

5.2. RF AGC
Item/Preparation Adjustment Procedure
1. Receive a colour bar pattern. 1. Set RF AGC Control such as to procedure a snowy picture.
2. Set the input level to 66 (+1.2) db. 2. Set RF AGC Control at the point just before the voltage at AGC :
TPA 20 begins to drop.
(75Ω opened)
3. Increase the input level by 3 db and confirm that the voltage
3. Connect an oscilloscope to AGC : TPA 20 with DC mode.
changes.

5.3. HIGH VOLTAGE

Item/Preparation Adjustment Procedure
1. Operate the TV set. 1. Connect a DC voltage meter to D850 cathode and confirm the
voltage is 141.0±2.0V.
2. Connect a high voltage meter (Electrostatic Type) to an anode of
2. Receive the crosshatch pattern.
the picture tube.
3. Confirm that the high voltage is within the range of 31.0+0.7V,
3. Set to 0 Beam -1.5V.
(Screen Control : min. CONTRAST : min)

5.4. SUB TINT

Item/Preparation Adjustment Procedure
1. Receive a 3.58 MHz NTSC rainbow pattern 1. Adjust Sub NTSC Tint so that the peak of level of waveform is
similar to Fig. 3
2. Connect oscilloscope to A21 pin 6.
2. Receive the Rainbow pattern (3.58 MHz NTSC) on both of Main
3. Set controls:
and Sub pictures.
BRT............. ...CENTER
COLOUR........CENTER 3. Adjust Sub NTSC Tint 2 so that the peak of level of 1.3±0.5V
CONTRAST....MAX
NTSC TINT.....CENTER
AI................ ....OFF

5.5. SUB CONTRAST

Item/Preparation Adjustment Procedure
1. Receive a colour bar pattern. 1. Adjust Bright Colour:
a=2.4±0.2Vp-p
2. Adjust Sub Contrast Colour:
2. Connect an oscilloscope to TPA40.
b=2.4±0.1Vp-p
3. Connect a short jumper between D11-1 and D11-2 / TPA53 and
TPA54 FBT pin 3 or TPA34 and TPA32.
4. Set controls:
Picture menu ........ Dynamic Normal
AI .................... ......... off

8
 TX-25P80T

5.6. PAL COLOUR OUTPUT

Item/Preparation Adjustment Procedure
1. Receive PAL colour bar pattern. 1. Adjust Bright Control.
a = 2.3±-0.2Vp-p
2. Connect an oscilloscope probe to TPA40. 2. Adjust Sub Colour control.
3. Connect a short jumper to FBT pin 3 or TPA34 and TPA32. 3. Connect the osciloscope probe to TPA40.
4. Set control :
Picture menu........... ..........DYNA MIC NORMAL 4. Connect the waveform.
AI................ .................... ..off (for model with AI only)
b = 3.1±-0.5Vp-p

5.7. NTSC COLOUR OUTPUT

Item/Preparation Adjustment Procedure
1. Apply 3.58MHz NTSC Rainbow pattern. 1. Adjust Bright Control.
a = 2.3±-0.2Vp-p
2. Connect an oscilloscope to TPA40. 2. Connect the waveform.
b = 1.3±-0.5Vp-p
3. Connect a short jumper to FBT pin 3 or TPA34 and TPA32.
4. Set control :
Picture menu........... ............DYN AMIC CONTROL
Channel Colour Set...........ST D

9
 TX-25P80T

5.10. WHITE BALANCE (MARKET MODE CHK 3)

Preparation Write down the original value for each address adjustment
1. Receive a colour bar signal with colour “OFF”, and operate before adjusting anything.
the TV set for more than 15 minutes.
2. Set the picture menu to “DYNAMIC NORMAL” and the AI to
off.
3. Connect an oscilloscope to TPL7 with DC mode.
4. Set the TV set to Market Mode : white balance adjustment
(CHK 3).
5. Screen VR : Min.
6. Set the data level of SUB BRIGHT, R, G, B-CUTOFF and
R, G, B-DRIVE to the table values.
Display Date Level
R-CUT OFF 63
G-CUT OFF 128 8. Wedge A shown in Fig. 2 should be fixed within a range of
B-CUT OFF 63 45° to the left of the vertical line as shown.
R-DRIVE 128
9. After inserting wedge A, insert wedges B, C and D.
B-DRIVE 128
The wedges should be set 90° apart from each other.
SUB BRIGHT 63
10. Be certain that the four wedges are firmly fixed and the
Adjustment deflection yoke is tightly clamped in place otherwise the
1. Select G-CUTOFF adjustment mode and collapse vertical deflection yoke may shift its position and cause a loss of
scan. convergence and purity.
2. Adjust G-CUTOFF control to become the DC=0 V to video
level at 180 V as shown in Fig. 1.

Fig. 1

3. Slowly turn the screen control clockwise until a green colour

horizontal line appears on the picture tube. This is the
setting point for the screen control.
Note:
Do not adjust the G-CUTOFF setting in the following
procedure.

4. Adjust the remaining R and B-CUTOFF controls so as to

get a white horizontal line on the screen.

5. Return to full field SCAN by pushing the position 5 key on

the remote control.
6. Adjust the R-Drive and B-Drive controls as to obtain a
uniform white on the white bar of the greyscale pattern.
7. Confirm correct B/W rendition and greyscale tracking or
repeat CUTOFF and drive control setup.
Note:

11