Scribd
Upload
69 views3 pages

CE302 B

This document contains 8 questions related to the design of reinforced concrete structures. The questions cover the design of slabs, footings, domes, retaining walls, and water tanks. The document provides relevant design parameters like dimensions, loads, material grades, and soil properties for answering each question. Students are asked to attempt 5 questions total by selecting at least one from each of the 4 sections.

Uploaded by

sahilkaushik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
69 views3 pages

CE302 B

This document contains 8 questions related to the design of reinforced concrete structures. The questions cover the design of slabs, footings, domes, retaining walls, and water tanks. The document provides relevant design parameters like dimensions, loads, material grades, and soil properties for answering each question. Students are asked to attempt 5 questions total by selecting at least one from each of the 4 sections.

Uploaded by

sahilkaushik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Section C No. of Printed Pages : 05 Roll No. .......................

5. Design a semi-circular beam supported on three


equally spaced columns. The centres of the
F-71
columns are on a circular curve of 10 m B. Tech. EXAMINATION, May 2018
diameter. The beam carries designed live and
(Sixth Semester)
imposed load of 20 kN/m. Use M 25 grade of
(B. Scheme) (Main & Re-appear)
concrete and Fe 500 grade of steel. 15
(CE)
6. Design the reinforced concrete spherical dome
CE302B
for a circular room of 10 m inside diameter.
REINFORCED CONCRETE DESIGN-II
The dome is supported over 340 mm thick
brick walls. The rise of dome is 3 m. Live and
Time : 3 Hours] [Maximum Marks : 75
imposed loads may be taken 3 kN/m2. Use
M 25 grade of concrete and Fe 415 grade of Before answering the question-paper candidates
steel. 15 should ensure that they have been supplied to correct
and complete question-paper. No complaint, in this
Section D regard, will be entertained after the examination.
7. A retainining wall has the following data : Note : Attempt Five questions in all, selecting at
Total height of embankment including bottom least one question from each Section. All
questions carry equal marks. Use of Indian
of base slab 500 mm depth = 7 m
Standards is allowed. Any data if missing
Top of stem = 200 mm, Bottom base width of can be suitably assumed. Use of scientific
stem = 500 mm. calculator is allowed.
M-F-71 4 (2-38/15) M-F-71 P.T.O.
Section A Section B
3. Design a reinforced concrete rectangular
1. Design a continuous one way slab for a railway footing of width not exceeding 2.3 m for a
platform supported on cantilever beam 2.5 m column section 300×450 mm and carries 1250
on each side of central columns as shown on kN load under service state. The soil has angle
figure. The slab has been cost monolithic with of repose 30º, density 19 kN/m3 and allowable
the beams. The columns are square in shape bearing pressure 130 kN/m2 at a depth of 1.25
m. Use M20 grade of concrete and Fe500
of 300 m size and spaced 5 metres centre to grade of steel. 15
centre. The superimposed load may be taken
4. A combined trapezoidal footing 900 mm overall
2 kN/m2. M20 grade concrete and Fe415 grade
depth carries two square columns of 400 mm each
of steel are to be used. 15 which carry service axial loads of 1500 kN and
1000 kN, respectively. The arrangement made for
the footing has been shown in figure. Allowable
bearing capacity of soil had been 175 kN/m2.
M20 grade of concrete and Fe 500 grade of steel
were used. The designed base slab had 20 mm 
@ 125 mm c/c as main longitudinal
reinforcement. Check whether the base slab was
safe against shear. 15

2. Design an interior panel with drops of a flat


slab for live load of 5 kN/m2. The gride of
column is 5×5 m. The columns are 300 mm in
size of square shape. Use M 20 grade of
concrete and Fe 500 grade of steel. 15

M-F-71 2 (2-38/16) M-F-71 3 P.T.O.


Base slab width = 4m Toe = 1.7 m Base slab width = 4m Toe = 1.7 m
Density of soil = 19 kN/m3, angle of repose = Density of soil = 19 kN/m3, angle of repose =
29º, allowable soil bearing pressure = 160 kN/ 29º, allowable soil bearing pressure = 160 kN/
m2. m2.
Design the stem of retaining wall and show Design the stem of retaining wall and show
the curtailment of steel. Use M 20 grade of the curtailment of steel. Use M 20 grade of
concrete and Fe500 grade of steel. 15 concrete and Fe500 grade of steel. 15

8. Use IS : 3370 2009 to design a circular water 8. Use IS : 3370 2009 to design a circular water
tank of capacity 400 m3 resting on the ground tank of capacity 400 m3 resting on the ground
and having a fixed base condition due to rigid and having a fixed base condition due to rigid
joint between the wall and the base slab. joint between the wall and the base slab.
M 30 grade of concrete and Fe 415 grade of M 30 grade of concrete and Fe 415 grade of
steel are to be used. 15 steel are to be used. 15

M-F-71 5 830 (2-38/17) M-F-71 5 830

You might also like