ME6301

Downloaded From : www.EasyEngineering.
net
ww
w.E
asy
En
gin
eer
ing
.ne
t
**Note: Other Websites/Blogs Owners Please do not Copy (or) Republish

this Materials without Legal Permission of the Publishers.
**Disclimers : EasyEngineering not the original publisher of this Book/Material

on net. This e-book/Material has been collected from other sources of net.
Downloaded From : www.EasyEngineering.net
ME6301 ENGINEERING THERMODYNAMICS LTPC

3 0 03
OBJECTIVES:
o To familiarize the students to understand the fundamentals of thermodynamics

and to perform thermal analysis on their behavior and performance.
(Use of Standard and approved Steam Table, Mollier Chart, Compressibility
Chart and Psychrometric Chart permitted)
ww
UNIT I BASIC CONCEPTS AND FIRST LAW 9
w.E
Basic concepts - concept of continuum, comparison of microscopic and macroscopic
approach. Path and point functions. Intensive and extensive, total and specific
asy
quantities. System and their types. Thermodynamic Equilibrium State, path and
En
process. Quasi-static, reversible and irreversible processes. Heat and work transfer,
gin
definition and comparison, sign convention. Displacement work and other modes of
work .P-V diagram. Zeroth law of thermodynamics – concept of temperature and
eer
thermal equilibrium– relationship between temperature scales –new temperature
ing
scales. First law of thermodynamics –application to closed and open systems –
steady and unsteady flow processes.
.ne
UNIT II SECOND LAW AND AVAILABILITY ANALYSIS
Heat Reservoir, source and sink. Heat Engine, Refrigerator, Heat pump. Statements
9
t
of second law and its corollaries. Carnot cycle Reversed Carnot cycle, Performance.
Clausius inequality. Concept of entropy, T-s diagram, Tds Equations, entropy change
for - pure substance, ideal gases - different processes, principle of increase in
entropy. Applications of II Law. High and low grade energy. Available and non-
available energy of a source and finite body. Energy and irreversibility. Expressions
for the energy of a closed system and open systems. Energy balance and entropy
generation. Irreversibility. I and II law Efficiency.
ii

UNIT III PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE 9
Formation of steam and its thermodynamic properties, p-v, p-T, T-v, T-s, h-s
diagrams. p-v-T surface. Use of Steam Table and Mollier Chart. Determination of
dryness fraction. Application of I and II law for pure substances. Ideal and actual
Rankine cycles, Cycle Improvement Methods - Reheat and Regenerative cycles,
Economiser, preheater, Binary and Combined cycles.
UNIT IV IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS 9
ww
Properties of Ideal gas- Ideal and real gas comparison- Equations of state for ideal
and real gases- Reduced properties-.Compressibility factor-.Principle of
w.E
Corresponding states. -Generalised Compressibility Chart and its use-. Maxwell
relations, Tds Equations, Difference and ratio of heat capacities, Energy equation,
asy
Joule-Thomson Coefficient, Clausius Clapeyron equation, Phase Change Processes.
Simple Calculations.
En
UNIT V GAS MIXTURES AND PSYCHROMETRY
gin 9
eer
Mole and Mass fraction, Dalton’s and Amagat’s Law. Properties of gas mixture –
Gibbs function. Psychrometric ing

Molar mass, gas constant, density, change in internal energy, enthalpy, entropy and
properties, Psychrometric charts. Property
calculations of air vapour mixtures by using chart and expressions. Psychrometric .ne
process – adiabatic saturation, sensible heating and cooling, humidification,
dehumidification, evaporative cooling and adiabatic mixing. Simple Applications
t
TOTAL : 45 PERIODS
iii

TABLE OF CONTENTS
Objective of the subject ------------------------------------------------------------ V
Detailed Lesson Plan ------------------------------------------------------------VII

Unit-I Basic Concepts and First Law
Part A ------------------------------------------------------------ 1
Part B ------------------------------------------------------------3
Part C ------------------------------------------------------------23
ww
Unit-II Second Law and Availability Analysis
Part A ----------------------------------------------------------- 25
Part B w.E -----------------------------------------------------------30

Part C
asy ------------------------------------------------------------51
En
Unit III Properties of Pure Substance and Steam Power Cycle
Part A
Part B gin
-----------------------------------------------------------54
-----------------------------------------------------------60
Part C eer
------------------------------------------------------------71
Unit- IV Ideal and Real Gases, Thermodynamic Relations ing

Part A
.ne
-----------------------------------------------------------76
Part B
Part C
-----------------------------------------------------------80
------------------------------------------------------------91
t
Unit - V Gas Mixtures and Psychrometry
Part A -----------------------------------------------------------92
Part B -----------------------------------------------------------95
Part C ----------------------------------------------------------115
Previous Year Question Papers ----------------------------------------------------------- 119
iv

ME6301 ENGINEERING THERMODYNAMICS
Objectives of the Subject

 To familiarize the students to understand the fundamentals of
thermodynamics and to perform thermal analysis on their behavior and
performance.
 To understand the basic terminologies and basic concepts of thermodynamics
ww
such as system, processes and cycles and about the thermodynamics properties
emerging out of laws of thermodynamics.

w.E
To integrate zeroth and first law to coin second law of thermodynamics and
to understand the concepts of Carnot cycle, Classius inequality, application of
 asy
second law and availability analysis.
To study about the properties of pure substances and application of first and
En
second law to for pure substances and also extension to steam power cycles such as
Ranking cycle.

gin
To learn about the properties of ideal and real gases to compare and contrast
against them and about thermodynamic relations and to apply the concepts of
eer
thermodynamic principles to Psychometrics processes.

ing
To apply the principles of thermodynamics to Mechanical Engineering
applications.
Need and Importance for Study of the subject

.ne
Thermodynamics is one of the most fundamental courses in mechanical
engineering. Anything and everything in the day to day life carry the aspects of the t
application of thermodynamics right from energy conversion during metabolism to
energy harnessing from sources. Knowledge of thermodynamics helps to
understand how power plant works whether it is gas or thermal power plant.For
analysing and designing Heat exchangers, pumps,compressors, boilers, combustion
chambers, turbines,condensors, refrigeration and air conditioning, IC engine,flow
through pipes and so on you need strong thermodynamics knowledge and i think all
this is done by mechanical engineers in particular this subject deals with the

application in IC engines, Aircraft engines, compressors, nozzles, refrigerators and

air conditioning system.
Industry Connectivity and Latest Developments

Since this is a fundamental subject, the students will be taken to Thermal labs and
Fluid Machinery labs where the application of thermodynamic concepts can be very
well explained.
Industrial Visit (Planned if any)
ww
Course Outcomes
The students will be able to
1.
w.E
Differentiate between open and closed system and various thermodynamics
flow and non flow processes. Understand the direction of heat flow and the
2. asy
possibility of any real processes and also about maximum available energy
To understand the formation of steam and properties of pure substances and
3.
steam.
En
To use the properties of ideal and real gases to apply the concepts in
gin
compressible flow and know the implementation of laws of thermodynamics
4.
on thermodynamic relations.
eer
To apply the concepts of thermodynamic principles to Psychometrics
5.
processes.
ing
To apply the principles of thermodynamics to Mechanical Engineering
applications.
.ne
Pre-requisites
The pre-requisite knowledge required by the Students to study this Course are
t
Engineering Physics, Engineering chemistry and Basic Mathematics.
vi

ME6301- ENGINEERING THERMODYNAMICS

DETAILED LESSON PLAN
Refer
Sl. Unit Hou
Topic ence
No. No. rs
s
BASIC CONCEPTS AND FIRST LAW
Basic concepts - concept of continuum, comparison of 2 T1,
ww
1. microscopic and macroscopic approach T2
2. w.E
Path and point functions. Intensive and extensive, total 2
and specific quantities. System and their types.
T1,
T2
3. asy
Thermodynamic Equilibrium State, path and process.
Unit- Quasi-static, reversible and irreversible processes.
2 T1,
T2
1
En
Heat and work transfer, definition and comparison, 2 T1,
4. gin
sign convention. Displacement work and other modes
of work .P-V diagram
T2
eer
Zeroth law of thermodynamics – concept of 2 T1,
5. ing
temperature and thermal equilibrium– relationship T2
between temperature scales –new temperature scales.
First law of thermodynamics –application to closed 2 .neT1,
6. and open systems – steady and unsteady flow

processes.
T2
t
Unit I 12
Cumulative Hrs. 12
SECOND LAW AND AVAILABILITY ANALYSIS
Heat Reservoir, source and sink. Heat Engine, 2

Unit- T1,
7. Refrigerator, Heat pump. Statements of second law
2 T2
and its corollaries.
vii

Carnot cycle Reversed Carnot cycle, Performance. 3

T1,
8. Clausius inequality. Concept of entropy, T-s diagram,
T2
Tds Equations
Entropy change for - pure substance, ideal gases - 2 T1,

9. different processes, principle of increase in entropy. T2
Applications of II Law. High and low grade energy. 3

T1,
10. Available and non-available energy of a source and
T2
finite body. Energy and irreversibility.
Expressions for the energy of a closed system and 2

ww
11. open systems. Energy balance and entropy generation.
Irreversibility. I and II law Efficiency.
T1,
T2
w.E Unit II 12
asy Cumulative Hrs. 24
En
PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE
gin
Formation of steam and its thermodynamic properties, 4
12. eer
p-v, p-T, T-v, T-s, h-s diagrams. p-v-T surface. Use of
Steam Table and Mollier Chart. Determination of
T1,
T2
dryness fraction.
ing 2
.neT1,
13.
Unit- Application of I and II law for pure substances.
3
Ideal and actual Rankine cycles, Cycle Improvement 4
T2
T1,
t
14. Methods - Reheat and Regenerative cycles,
T2
Economiser, preheater
Binary and Combined cycles. 2 T1,

15. T2
Unit III 12
Cumulative Hrs
36
.
viii

IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS
Properties of Ideal gas- Ideal and real gas comparison- 3

T1,
16. Equations of state for ideal and real gases- Reduced
T2
properties
Compressibility factor-.Principle of Corresponding 2 T1,

17. T2
Unit- states. -Generalised Compressibility Chart and its use
4 4
Maxwell relations, Tds Equations, Difference and ratio
T1,
18. of heat capacities, Energy equation, Joule-Thomson
T2
Coefficient
ww Clausius Clapeyron equation, Phase Change Processes. 3 T1,
19.
w.E
Simple Calculations.
Unit IV 12
T2
asy Cumulative Hrs
En
GAS MIXTURES AND PSYCHROMETRY
.
48
gin
Mole and Mass fraction, Dalton’s and Amagat’s Law. 2 T1,
20. Properties of gas mixture
eer T2
21. ing
Molar mass, gas constant, density, change in internal
energy, enthalpy, entropy and Gibbs function
3 T1,
T2
Unit- Psychrometric properties, Psychrometric charts. 3 .ne

22. 5 Property calculations of air vapour mixtures by using
chart and expressions.
T1,
T2
t
Psychrometric process – adiabatic saturation, sensible 4
heating and cooling, humidification, dehumidification, T1,
23. evaporative cooling and adiabatic mixing. Simple T2
Applications
Unit V 12
60
Cumulative Hrs.
ix

TEXT BOOKS :
1. Nag.P.K., “Engineering Thermodynamics”, 4thEdition, Tata McGraw-Hill, New

Delhi, 2008.
2. Natarajan E., "Engineering Thermodynamics: Fundamentals and Applications",

Anuragam Publications, 2012.
REFERENCES :
1. Cengel. Y and M.Boles, "Thermodynamics - An Engineering Approach", 7th

Edition, TataMcGraw Hill, 2010.
ww
2. Holman.J.P., "Thermodynamics", 3rd Edition, McGraw-Hill, 1995.
w.E
3. Rathakrishnan. E., "Fundamentals of Engineering Thermodynamics", 2nd Edition,
Prentice-Hall of India Pvt. Ltd, 2006
asy
4. Chattopadhyay, P, "Engineering Thermodynamics", Oxford University Press, 2010.
En
5. Arora C.P, “Thermodynamics”, Tata McGraw-Hill, New Delhi, 2003.
gin
6. Van Wylen and Sonntag, “Classical Thermodynamics”, Wiley Eastern, 1987
eer
7. Venkatesh. A, “Basic Engineering Thermodynamics”, Universities Press (India)
Limited, 2007.
ing
8. Kau-Fui Vincent Wong, "Thermodynamics for Engineers", CRC Press, 2010 Indian
Reprint.
.ne
9. Prasanna Kumar: Thermodynamics "Engineering Thermodynamics" Pearson
Education, 2013 t

UNIT-1
BASIC CONCEPTS AND FIRST LAW
PART-A
1. What is microscopic approach in thermodynamics? Nov/Dec-2013

In microscopic approach, thermodynamic properties are considered at the
molecular level. This approach is also called as statistical thermodynamics.
2. Define extensive property. Nov/Dec-2013
ww
The properties which are dependent on the mass of the system are called extensive
w.E
properties. Example: Total energy, Total volume, weight etc.
asy
3. Define: Thermodynamic Equilibrium. May/June-2014
En
A system will be in a state of thermodynamic equilibrium, if the conditions for the
following three types of equilibrium are satisfied.
gin
(a) Mechanical equilibrium
(b) Thermal equilibrium eer
(c) Chemical equilibrium
ing
4. Differentiate between point function and Path function.
.ne
May/June-2014
The quantities which are independent on the process or path followed by the
system is known as point functions.
t
Example: Pressure, volume, temperature, etc.,
The quantities which are dependent on the process or path followed by the system
is known as path functions.
Example: Heat transfer, work transfer.
5. Enlist the similarities between work and heat. Nov/Dec-2014

i) Both work and heat are directional quantities because both have magnitude
and direction in relation to whether the energy is entering or leaving the system.
ii) Both are boundary phenomenon because they are only recognised when
energy crosses the system boundary.
iii) According to the second law of thermodynamics statements, a system
processes energy.
iv) Both work and heat are associated with a process as the system follows a
path from state to another state.
ww v) Both work and heat are path functions
w.E
6. Compare heat transfer with work transfer Nov/Dec-2014
Heat is a form of energy in transit. It is a boundary phenomenon, since it occurs only
asy
at the boundary of a system. Energy transfer by virtue of temperature difference
En
only is called heat transfer. All other energy interactions may be termed as work
transfer.
gin
eer
7. State the first law for a closed system undergoing a process and a cycle.
April/May-2015
ing
First law of thermodynamics states that when system undergoes a cyclic process
The net heat transfer is equal to work transfer. ∮Q = ∮ W .ne
8. Why does free expansion have zero work transfer? April/May-2015
t
The expansion of a gas against vacuum is called as free expansion.
The reasons for free expansion have zero work transfer are:
1. There is no work crosses boundary of the system.
2. It is not a quasi-static process
3. There is no resistance to the fluid.

9. Define the Zeroth law of thermodynamics. April/May-2015,2016
Zeroth law of thermodynamics states that when two systems are separately in
thermal equilibrium with a third systems, then they themselves are in thermal
equilibrium with each other. It is a base for temperature measurement.
10. List any five physical properties of matter which can be used for
measurement of temperature. April/May-2015
Pressure, Volume, Resistance, Thermal e.m.f, Length
ww
11. State the thermodynamic definition of work. Nov/Dec-2015
In thermodynamics, Work is said to be done by a system if the sole effect on things
w.E
external to the system can be reduced to the raising of a weight.
asy
12. Classify the following properties as intensive or extensive or neither
f) Enthalpy per unit mass. En

a) Pressure b) Temperature c) Volume d) Internal energy e) Volume per mole
Nov/Dec-2015
a. Pressure – Intensive property gin
b. Temperature – Intensive property
eer
c. Volume – Extensive property
d. Internal energy – Extensive property ing
e. Volume per mole – Intensive property .ne
f. Enthalpy per unit mass - Intensive property
PART - B
t
1. A mass of air is initially at 260 and 700kPa, and occupies 0.028m3. The
air is expanded at constant pressure to 0.084m3. A polytrophic process
with n=1.5 is then carried out followed by a constant temperature process
which completes a cycle. All the processes are reversible.
i) Sketch the cycle in T-S and P-V planes
ii) Find the heat received and heat rejected in the cycle.

iii) Find the efficiency of the cycle. May/June – 2016
Given Data:
T1 = 260
P1 = 700kPa = P2
V1 = 0.028 m3
Process 2-3 is polytropic
ww
V2 = 0.084 m3
Process 1-2 is constant pressure
w.E
Process 3-1 is constant temperature
To find:
asy
Sketch P-V and T-S diagram,
En
Q and
gin
Solution:
eer
ing
.ne
t
Process 1-2:
1. Constant pressure process,
T2 = 1599K

Mass of air, m= = 0.128 kg
Workdone, W 1-2 = p (V2-V1) = 39.2kJ
Heat transfer, Q 1-2 = mCp(T1-T1) = 137.13kJ
Process 2-3:
For polytropic process,
ww
w.E P3 = 25.93kPa
From pV = mRT
asy V3 = = 0.755 m3
En
Polytropic work, W 2-3 =
gin
= 78.446 kJ
Heat transfer, Q 2-3 = eer

x W2-3 = -19.612 kJ
Process 3-1 ing

T1 = T3 = 260 =533 K for constant temperature process .ne
Work transfer, W 3-1 = -p3V3ln
t
Q = -64.52 kJ (work input)
Heat received in this cycle, Qs = 137.13 kJ (consider only +ve heat)
Heat rejected in this cycle, QR = 84.132 kJ (consider only –ve heat)
Efficiency of the cycle,

Efficiency of the cycle, = 38.74%
2. A room for four person has 2 fans each consuming 0.18 kW power and
three 100 W lamps. Ventilation air at the rate of 80kg/hr enters with an
enthalpy of 84 kJ/kg and leaves with an enthalpy of 59 kJ/kg. If each person
puts out heat at the rate of 630 kJ/hr. determine the rate at which heat is
removed by a room cooler, so that a steady state is maintained in the room.
May/June–2016 (8marks)
ww
Given Data:
np = 4 (person), nf = 2
w.E
Wf =0.18kW (each)
asy
W1 = 100W (each)
Mass of air, m = 80kg/hr
En
Enthalpy of air entering, h1 = 84 kJ/kg
Enthalpy of air leaving, h2 = 59 kJ/kg gin

Qp =630 kJ/hr (each person) eer
To find: ing
The rate of heat is to be removed
.ne
Solution:
Rate of energy increase = Rate of energy inflow – Rate of energy outflow t
E=m -m ...... (1)
Assuming that,
Now , the equation (1) reduces to

Q= E-m (h1 – h2)-W
= -0.7kW

m (h1 – h2) = 0.55kW
W= electrical energy input
= nfWf + nlWl
= 0.66kW
Q = -0.7 - 0.556 - 0.66 = -1.916 Kw
b) An insulated rigid tank of 1.5 m3 of air with a pressure of 6 bar and 100
discharges air in to the atmosphere which is at 1 bar through a discharge pipe
ww
till its pressure becomes 1 bar.
w.E
i) Calculate the velocity of air in the discharge pipe.
ii) Evaluate the work that can be obtained from the frictionless turbine
asy
using the kinetic energy of that air. May/June – 2016(8 marks)
Given Data:
En
Vi = Vf = V =1.5 m3
gin
pi = 6 bar = 600kPa
eer
pf = 1 bar = 100kPa
ing
Td = Tf
.ne
R = 0.287 kJ/kg.K
t
CV = 0.718 kJ/kg.K
For air Cp = 1.005 kJ/kg.K
To Find:
i) velocity of air in the discharge pipe
ii) work that can be obtained from the frictionless turbine using the
kinetic energy of that air

Solution:
It is the case of Tank discharged air. As it is insulated (Q=0), it can be

considered as adiabatic process.
Tf = 223.6K
mi =
ww mf =
w.E
Q=(
asy =0 in kJ/kg
Cd =
En
C2 = 410.9 m/s
gin
Turbine work = Kinetic energy =
eer = 51290 J
Turbine work = kinetic energy = 512.59 KJ

ing
3. Determine the heat transfer and its direction for a system in which a
perfect gas having molecular weight of 16 is compressed form 101.3kPa, .ne
20 to a pressure of 600 kPa following the law pV1.3=constant. Take
specific heat at constant pressure of gas as 1.7kJ/kg K. May/June – 2014
t
Given Data:
Molecular weight M =16
P1= 101.3kPa
p2 = 600kPa
T1= 20+273 = 293K

pV1.3=constant
R = 0.287 kJ/kg.K
Cp = 1.7 kJ/kg.K
To Find:
Q and its Direction
Solution:
ww Gas constant of perfect gas ,
w.E R = Ru/M = 8.314/16 = 0.508

R = Cp - CV = 1.7 – 0.508
asy = 1.192 kJ/kg.K
En
= Cp/ Cv = 1.7/1.192=1.42
T= T1 (P2/P1) n-1/n
gin
eer
= 293(600/101.3)1.3-1/1.3
= 441.11K ing
Work transfer W = = .ne
= -250.79 kJ/kg t
Heat transfer Q = xW= x -250.79
= -71.65 kJ/kg
The negative sign indicates the heat rejection from the system
4. Three grams of nitrogen gas at 6 atm and 100 in a frictionless piston

cylinder device is expanded adiabatically to double its initial volume, then
compressed at constant pressure to its initial volume and then compressed
9

again at constant volume to its initial state. Calculate the net work done on
the gas. Draw the P-V diagram for the processes. Nov/Dec – 2014
Given Data:
m =3kg
P1= 6atm = 6x1.0132 = 6.0792bar
= 6.0792X100 = 607.92kPa
T1 = 160oC= 160+273 = 433K
ww Process 1-2 is adiabatic expansion (V2=2V1)
w.E
Process 1-2 is Constant pressure process (P2=P3)
Process 1-2 is Constant volume process (V3=V1)
To Find:
asy Wnet
En
Solution:
gin
Molecular weight of nitrogen M =2x14 = 28
Gas constant of nitrogen gas , eer
ing
R = Ru/M = 8.314/28 = 0.297 kJ/kg.K
.ne
t
Process 1-2
Adiabatic expansion process
P1 V1γ = P2 V2γ
10

= 6.0792 x
= 2.304bar = 230.4kpa
From ideal gas equation,
P1V1 = mRT1
V1 = = = 0.000635m3
V2 = 2V1 = 2 x 0.000635m3
ww Work done W1-2 =
w.E = = 0.319KJ
asy
Process 2-3
For Constant Pressure process

En
Work done, W2-3 = P2 ( V3 – V2)
gin
= 230.4 x (0.000635 – 0.00127) (. . .V3 – V1)
= - 0.146KJ eer
Process 3-1
For Constant Volume process ing
Work done, W3-1 = 0
.ne
Net Work done Wnet = W1-2 + W2-3 + W3-1
= 0.319 - 0.146 + 0
t
= 0.173KJ
5. 90kJ of heat is supplied to a system at a constant volume. The system
rejects 95kJ of heat at constant pressure and 18 kJ of work is done on it.
The system is brought to original state by adiabatic process. Determine
Nov/Dec- 2014
i) The adiabatic work
ii) The values of internal energy at all states if initial value is 105kJ.
11

Given Data:
Q1-2 = 90KJ
Q2-3 = -95KJ (negative sign indicates the heat rejection)
W2-3 = -18KJ (negative sign indicates the work done on the system)
Process 3-1 is adiabatic. So Q2-3 = 0
U = 105KJ
ww
To find:
W, ∆U
w.E
Solution:
asy
En
gin
eer
ing
Process 1-2
.ne
For Constant Volume process
Work done, W 1-2 = 0 t
Based on first law of thermodynamics,
Heat done Q 1-2 = W 1-2 + ∆U
∆U = 90KJ
But ∆U = U2 - U1
90 = U2 – 105
12

U2 = 195KJ
Process 2-3
For Constant Pressure process
Q 2-3 = -95KJ
W 2-3 = -18KJ
Heat done Q 1-2 = W 1-2 + ∆U

ww 95 = -18 + ∆U
w.E But
∆U = -95 + 18 = -77KJ
asy ∆U = U3 – U2
En
-77 = U3 – 195
U3 = 195 – 77 gin
= 118KJ
eer
Process 1-2
For adiabatic process ing
Q 2-3 = 0 .ne
Φ dQ = Φ dW
t
Q 1-2 +Q 2-3 +Q 3-1 = W 1-2 + W 2-3 + W 3-1
90 – 95 + 0 = 0 -18 + W 3-1
W 3-1 = 13KJ
6. Air flows steadily at the rate of 0.04 kg/s through an air compressor,
entering at 6 m/s with a pressure of bar and a specific volume of 0.85 m 3/kg
13

and leaving at 4.5 m/s with a pressure of 6.9 bar and a specific volume of 0.16
m3/kg. The internal energy of the air leaves at 88 kJ/kg greater than that of
entering air. Cooling water surrounding the cylinder absorbs heat from the air
at the rate of 59W. Calculate the power required to drive the compressor and
the inlet and outlet cross-sectional areas. Nov/Dec – 2015(16marks)
Given Data:
m = 0.5Kg
C1 = 6m/s
ww P1 = 100kpa
w.E
v1 = 0.85m3/kg
asy
C2 = 5m/s
P2 = 690kpa
En
v2 = 0.16m3/kg
gin
u2-u1 = 88KJ/Kg
eer
Q = -59Kw
ing
To find:
.ne
P, D1/D2
Solution: t
Steady Flow Energy Equation (SFEE) given by
m(u1+p1v1+C12/2 + Z1g) + Q = m(u2+p2v2+C22/2 + Z2g) + W
0.04 (100 x 0.85) + 62/20000) – 59 = 0.04 (690 x 0.16) + 52/20000) + W

Work input W = - 63.52 Kw
The negative sign indicates that the work is done on the system
From Continuity equation
14

A1C1/v1 = A2C2/v2
A1/ A2 = C2v1 / C1 v2
D1/D2 = 1.99
7. A gas undergoes a thermodynamic cycle consisting of the following process:

(i) Process 1-2 : constant pressure p1 = 1.4 bar, V1 = 0.028m3, W12 = 10.5 kJ.
(ii) Process 2-3 : Compression with pV = constant, U3 = U2
(iii) Process 3-1: Constatn volume U1 – U3 = -26.4kJ.
wwThere are no significant changes in KE and PE
w.E
1) Sketch the cycle on a pV diagram.
2) Calculate the network for the cycle in kJ.
asy
3) Calculate the heat transfer for process 1-2
4) Show that =
En May-June 2015
Given Data:
P1 = p2 = 1.4 Bar
gin
V1 = 0.028m3 eer
Work interaction W 1-2 = 10.5KJ ing
2-3Compression process with pV = Constant .ne
3-1 Constant volume process t
U1-U2 = -26.4KJ
To find
Wnet
Q
Solution:
1-2 constant pressure process:
W 1-2 = p1(V2-V1)
15

V2 = 0.103 m3
ww 2-3 constant temperature process:
w.E
W 2-3 = p2V2ln
asy
W = -18.78kJ
Change in internal energy,
En
for isothermal process
gin
Heat transfer, Q2-3= work transfer, W = -18.78kJ
3-1 constant volume process:
eer
V1 =V3= 0.103m3
ing
Work transfer, W 3-1 = 0
Heat transfer, Q 3-1= U1-U3 = -26.4kJ .ne

Network of the cycle, Wnet = W 1-2 +W 2-3 +W 3-1
= -8.28kJ
t
Internal energy for process 1-2, U 1-2
U 1-2 = U2 – U1
= 26.4 kJ
Heat transfer, Q 1-2 = W 1-2 + U 1-2
= 36.9 kJ
Net heat transfer of the cycle,
16

Q net = Q 1-2 +Q 2-3 +Q 3-1

= - 8.28kJ
Hence, = proved.
8. A gas occupies 0.3 m3 at 2 bar. It executes a cycle consisting of processes:
(i) 1 - 2, constant pressure with work interaction of 15kJ
(ii) 2 - 3, compression process which follows the law pV = C and

U3 = U2 and
ww (iii) 3 - 1, constant volume process, and reduction in internal
w.E energy is 40kJ
Neglecting the changes in Kinetic energy and Potential
asy energy. Draw pV diagram for the process and determine

network transfer for the cycle. Also show that first law is
obayed by the cycle.
En April-May 2017 (13 MARK)
Given:
gin
p1 = p2 = 2 bar = 200 kN/m2
eer
V1 = 0.3 m3
ing
W1-2 = 15 kJ
.ne
U1- U3 = 40 kJ
To Find: t
Network transfer for the cycle?
Solution:
Process 1-2 Constant pressure process:
W1 2  p1 V2  V1 
15  200  V2  0.3
V2  0.375m 3
17

Process 2-3 Constant Temperature process:
V 
W23  p 2V2 ln  3 
 V2 
 0 .3 
 200  0.3  ln  
 0.375 
V3  V1 
W23  13.388kJ
Also , p 2V2  p3V3
200  0.375
p3 
ww 0 .3
p3  250 kN m 2
w.E
Change in internal energy U  0 forisother malprocess
asy
Process 3-1Constant volume process
V2 = V3 = 0.375 m3
Work transfer, W = 0 En
Heat transfer, Q = 40 kJ gin
eer
9. In a gas turbine, the gases enter the turbine at the rate of 5 kg/s with a
ing
velocity of 50 m/s and the enthalpy of 900 kJ/kg and leaves the turbine with
150 m/s and the enthalpy of 400 kJ/kg. The loss of heat from the gas to the
surroundings is 25 kJ/kg. Assume R = 0.285 kJ/kg K, Cp = 1.004 kJ/kg K and
the inlet conditions to be at 100 kPa and 27oC. Determine the work done and .ne
diameter of the inlet pipe.
Given:
April-May 2017 (13 MARK)
t
m = 5 kg/s
C1 = 50 m/s
h1 = 900 kJ/kg
C2 = 150 m/s
h2 = 400 kJ/kg
18

R = 0.285 kJ/kgK
Cp = 1.004 kJ/kgK
Q = -25 kJ/kg
p1 = 100 kPa T1 = 27 oC
To find:
1. work done
2. diameter of the inlet pipe.
ww
Solution:
w.E
The steady flow energy equation is given by
 C
2
 
 h1  1  Z 1 g   Q   h2 
C2
2

 Zg 
 W
asy

 2
Z1  Z 2



 2 

 900 


50 2   25 
2000   En 
 400 


150 2
2000

 W


876.25  411.25  W
W  465kJ / kg gin
Power  mW
 5  465 eer
 2325kW
m
A1C1 ing
weknow
V1
.ne
p1V1  mRT1
V1 
0.285  300
100
t
V1  0.855m 3
mV1
A1 
C1
5  0.855

50
A1  0.0855m 2

d 1  0.0855
2
4
d 1  0.3299m
19

10. A Piston –cylinder device contains 0.15kg of air initially at 2 MPa and
3500C. The air is first expended isothermally to 500KPa, then compressed
polytropically with a polytropic exponent of 1.2 to the initial pressure and
finally compressed at the constant pressure to the initial state .Determine the
boundary work for each process and the network of the cycle.
NOV/DEC 2016 (13 MARK)
Given data:
ww m =0.15kg
w.E
p1 =2MPa =2000KPa = p3
asy
T1 =3500C =270+350 =6213K =T2
P2 =500KPa
En
n =1.2
gin
Process 1-2 is isothermal (Expansion)
eer
Process 2-3 is polytropic (Compression)
ing
Process 3-1 is constant pressure (Compression)
.ne
Solution: t
20

Process 1-2:Isothermal Expansion process
Volume at rate,1 ,V1 =m R T1/ P1
= 0.15*0.287*623/2000
= 0.0134m3
Volume at rate,2 ,V2 =m R T2/ P2
= 0.15*0.287*623/500
ww = 0.054m3
w.E
Constant temperature process,
asy
Work transfer, W 1-2 = m R T1 ln(p1/p2)
En
W1-2 = 0.15*0.287*623 ln(2000/500)
= 37.18KJ gin
Process 2-3:Polytropic compression process eer
For Polytropic process, ing
P2V2n = P3V3n .ne
() ( )
p2
p3
500
2000
t
V3 = V2 = *0.054 =0.017m2
Polytropic work W2-3 = p 2 v 2 _ p 3 v 3 /n-1
= 500 x 0.054-2000x0.017/1.2-1
=-35KJ
Process 3-1:
Workdone, W3-1 = p3 (V1-V3) for constant pressure processes
21

=2000(0.0134-0.017)
= -7.2kJ
Net work, Wnet = W1-2 + W2-3 + W3-1
= 37.18 – 35 – 7.2
=5.2kJ
11. Air enters the compressor of a gas- turbine plant at ambient conditions of
100KPa and 250C with a low velocity and exits at 1MPa and 3470 C with a
ww
velocity of 90 m/s .The compressor is cooled at a rate of 1500KJ/min and the
power input to the compressor is 250KW. Determine the mass flow rate of air
w.E
through the compressor. Assume Cp = 1.005KJ/KgK
asy NOV/DEC 2016 (7 MARK)
Given data:
En
P1 = 100kPa gin
T1 = 250C =25+273=298K eer
C1 = 0 ing
P2 = 1MPa .ne
T2 = 3470 C =347+273 =620K t
C2 = 90 m/s
Q = 1500KJ/min
P = 250KW
Cp = 1.005KJ/KgK-
Solution:
22

SFEE is given by
m(h1 + C12/2 +Z1g) + Q = m(h2 + C22/2 +Z2g) + W
m( h1 - h2 ) + C12/2 - C22/2 = W-Q
Assume Z1 = Z2
m (1.005 (298 – 620 )+ 0 – 902/2000 = - 250-(-25)
m = 0.687 kg/s
ww PART - C
w.E
12. Air at 80 kpa, 27 oC and 220 m/s enters a diffuser at a rate of 2.5 kg/s and
leaves at 42 oC. The exit area of the diffuser is 400cm2. The air is estimated to
asy
lose heat at a rate of 18 kJ/s during this process.
(i)
En
the exit velocity and
(ii)
gin
the exit pressure of the air. APRIL/ MAY 2017 (15 MARK)
Given:
eer
P1 = 80 kPa = 80 kN/m 2
C1 = 220 m/s
ing
m = 2.5 kg/s .ne
T1 = 27 oC = 27 + 273 = 300 K t
T2 = 42 oC = 42 + 273 = 315 K
A2 = 400 cm2 = 0.04 m2
Q = -18 kJ/s
To find:
1. C2 = ?
2. P2 = ?
23

Solution:
For Isentropic flow

 1
T2  P2  
 
T1  P1 
1.4
 315  0.4
 80   
 300 
P2  94.89 kN m 2
ww
SFEE FOR Nozzle
w.E C
2
2
C
m  1  h1  Q  h2  2  m
2
2
asy C 2  2m h1  h2   Q  C1
2

E 
C 2  2  2.5 Cp T 1T2   Q  C1
n
2


gin 
C 2  5 1005300  315  18  220 2
C 2  408.08m / s
eer
ing
.ne
t
24

Unit – II
SECOND LAW AND AVAILABILITY ANALYSIS
Part - A
1. What is a thermal energy reservoir? Explain the term ‘Source’ and

‘Sink’.[Apr/May 15/ R-2013]
Thermal energy reservoir: Infinite body which supplies or receives the heat
continuously without change in its temperature.
wwSource: Reservoir which supplies the heat to work absorbing or work

developing device.
w.E
Sink: Reservoir which receives the heat from work absorbing or work
developing device.
asy
En
2. What is a reversed heat engine?[Apr/May-15/ R-2013]
gin
A reversed heat engine is a device works on reversed Carnot cycle which
absorbs work energy. Reversed heat engines operate as heat pump or
refrigerator.
eer
ing
3. Express Clausius inequality for various process.[Nov/Dec-15/R-2013]
or State Entropy principle .ne
a. t
b.
c.
4. Define second law efficiency.[Nov/Dec-15/R-2013]

Second law efficiency is defined as the ratio of change in the available energy
of the system and change in the available energy of the source.
25

5. State Clausius Statement of Second law of thermodynamics[Nov/Dec-

13/R-2008]
It states that it is impossible to construct a device which, operating in a cycle,
will produce no effect other than the transfer of heat from a cooler to a hotter
body.
6. State : Kelvin –Planck Statement.[May/June -14/ R-2008]
Kelvin-Plank states that it is impossible for a heat engine to produce net work
in a complete cycle if it exchanges heat only with bodies at a single fixed
wwtemperature.
7. Write Carnot theorem and its corollaries. [May/June -14/ R-2008]
w.E
Carnot theorem: It state that of all heat engines operating between a given
asy
constant temperature source and a given constant temperature sink, none has
a higher efficiency than a reversible engine.
Corollaries:
En
gin
1. The efficiency of all reversible heat engines operating between the same
temperature levels is the same.
eer
2. The efficiency of a reversible engine is independent of the nature or
ing
amount of the working substance undergoing the cycle.
8. An inventor claims to have developed an engine which absorbs 100 KW .ne

of heat from a reservoir at 1000 K produces 60 KW of work and rejects
heat to a reservoir at 500K. will you advise investment in its
t
development. [Nov/Dec-14/R-2013]
Given Data: Q = 100 kW; T1=1000 K;W=60 kW; T2 = 500K
Solution: Carnot efficiency
Engine efficiency
so it is not advisable to investment for develop this engine
26

9. A turbine gets a supply of 5 kg of steam at 7 bar, 250° C and discharged it

at 1 bar. Calculate the availability. [Nov/Dec-14/R-2013]
Given Data: m = 5 kg; P1=7 bar; T1=250° C; P2= 1bar
Solution: For turbine Availability
From Mollier diagram at @ 7 bar and 250°C h1 = 2954 kJ/kg;
Draw vertical line up to 1 bar and read enthalpy h2 = 2581 kJ/kg.
10. A reversible heat engine operates between a source at 800°C and a sink
ww
at 30°C. What is the least rate of heat rejection per kW network output of
w.E
the engine?[May/ June 2016/ R2013]
Given data : T1=800+273=1073 K, T2 = 30+273=303 K, W = 1 kW
asy
To find :Qr
Solution :
En
gin
eer
11. Define irreversibility? What ing are the causes of
irreversibility?[Nov/Dec-15/R-2008], [May/ June 2016/ R2013]
.ne
It is defined as the actual work done by a system is always less than the
idealized reversible work, and the difference between the two is called
t
irreversibility.
Causes of irreversibility:
i. Lack of equilibrium
ii. Heat transfer through a finite temperature difference
iii. Lack of pressure equilibrium within the interior of the system
iv. Free expansion
v. Dissipative effects
27

12. List the limitation of first law of thermodynamics?[May/June 2016/R8]
(i) First law of thermodynamics does not specify the direction of flow of
heat and work.
(ii) First law does not give any information on whether that changes of
state or process is at all feasible or not.
13. In an isothermal process 1000 kJ of work done by the system at a

temperature 200°C. What is the entropy change of this process?[May/ June
ww
2016/ R2008]
w.E
Given Data: W = 1000 kJ, T =200+273=473 K ; To find : ΔS = ?
In isothermal process Q = W = 1000 KJ
asy kJ/kg K
En
14. A closed insulated vessel contains 200 kg of water. A paddle wheel
gin
immersed in the water is driven at 400 rev/min with an average torque of 500
eer
Nm. If the test run is made for 30 minutes. Determine rise in the temperature
of water . Take specific heat of water 4.186 KJ/Kg K.[Apr/may-2015/ R2008]
ing
Given Data: mw = 200 kg; N=400 rpm; Torque =500 Nm; time t = 30 min;
Cpw = 4.186 KJ/Kg k
.ne
To find : ΔT
Solution : Work done by Paddle wheel(Brake power) = Heat gain by water t
; 45 ° C
15. A heat engine supplies with 2512 kJ/min of heat at 650°C. Heat rejection
take place at 100°C. specify which of the following heat rejection represents
reversible, irreversible or impossible result (i) 867 kJ/min (ii) 1015
kJ/min[Apr/May-2015/ R2008]
28

Given data : T1= 650+273 = 923K ; T2 = 100+273 = 373 K; Q 1 = 2512 kJ/min =41.87
kJ/sec; Q2(i) = 867 kJ/min = 14.45 kJ/sec ; Q2(ii) = 1015 kJ/min = 16.92 kJ/sec
Solution:
Case (i) Q2 = 867 kJ/min
it is impossible because
ww Case (ii) Q2 = 1015 kJ/min
w.E ; it is reversible because
asy
En
gin
eer
ing
.ne
t
29

PART – B
1. a. In a Carnot cycle the maximum pressure and temperature are limited

to 18 bar and 410°C. The volume ratio of isentropic compression is 6
and isothermal expansion is 1.5. Assume the volume of the air at the
beginning of isothermal expansion as 0.18m3. Show the cycle P-V and T-
S diagram and determine (i) the pressure and temperature at main
points (ii) Thermal efficiency of the cycle. [May/June -2016 / R-2008] (8
marks)
wwGiven Data :
w.E
The highest pressure P2 = 18 bar
The highest temperature T 2 = 410 + 273 = 683 K = T3
asy
Volume V2 = 0.18 m3
V1 = 1.08 m3
En
= 1.5 ; V3 = 0.27 m3
gin
Solution:
eer
Process 1-2:
ing
.ne
t
30

T1 = 333.5 K = T4
P2 = 1.46 bar
Process 2-3:
P2 V 2 = P3 V 3
ww 18 x 0.18 = P3 X 0.27
w.E
P3 = 12 bar
asy
Process 3-4 :
En
gin
eer
P4 = 0.977 bar. ing
.ne
Thermal efficiency of cycle
t
Thermal efficiency of the cycle = 51.16%
31

1.b. 5 m3 of air at 2 bar 27°C is compressed up to 6 bar pressure following

PV1.2 = constant. It is subsequently expanded adiabatically to 2 bar.
Considering the two process to be reversible, determine he network, net
heat transfer, change in entropy. Also plot the process on T-S and P-V
diagram [ MAY/JUN 2014 /R-2008] [8 marks]
Given Data :
V1 = 5m3
P1 = 2 bar
ww T1 = 27 +273 = 300 K
w.E
P2 = 6 bar
PV1.3 = C
n
asy = 1.3
P3 = 2 bar
En
Process
Reversible adiabatic
:
gin
1-2 Polytropic ; Process : 2-3
To find : W, Q, eer
ΔS and T-S and P-V Diagram
ing
.ne
t
Solution:
Process 1-2 :
From general equation
32

P1 V1 = m R T1
P1V1 2  100  5
m1    11.61kg
RT1 0.287  300
From polytropic Process relation
n1/ n
P  1.31/ 1.3
6
T2  T1  2   300   386.57 K
P  2
 1 
ww
Work done
mR(T1  T2 ) 11.61 0.287  (330  386.57)

w.E
W12 
n 1

1.3  1
 961.52kJ
asy
Heat transfer
 n
Q12  W12    961.52
  1 
En
 1.4  1.3 
 1.4  1 
  240.38kJ
gin
Change in entropy
eer
P T 
S1 2  mR ln  1   mC p ln  2 
 P2   T1 
ing
.ne
S12
2  386.57 
 11.61 0.287 ln    11.61 1.005  ln 
6  300 
  0.702kJ / K
t
Process 2-3:
From adiabatic process relation
 1/ 
P  2
1.41/ 1.4
T3  T2  3   386.57   282.43K
P  6
 2 
Work done
33

mR(T2  T3 ) 11.61 0.287  (386.57  282.43)

W23    867.5kJ
 1 1.4  1
Heat transfer for adiabatic process
Q2 3  0
Change in entropy
P  T 
S2 3  mR ln  2   mC p ln  3 
 P1   T2 
ww 6  282.43 
w.E
S 23  11.61 0.287 ln    11.611.005  ln 
 2
  0.00174kJ / K
 386.57 
asy
Net work transfer W = W1-2 + W2-3 = - 961.52+867.5 = -94.02 kJ
En
Net Heat transfer Q =Q1-2 + Q 2-3 = - 240.38 +0 = -240.38 kJ
gin
Change in entropy ΔS = ΔS1-2 + ΔS 2-3 = - 0.702 – 0.00174 = - 0.7034 kJ/K
eer
2. Two Carnot engines A and B are operated in series. The first one
ing
receives heat at 870 K and reject to a reservoir at T. B receives heat
rejected by the first engine and in turn rejects to a sink at 300 K. Find
the temperature T for (a) Equal work outputs of both engine (b) Same .ne
efficiencies [Nov/Dec-2013 / R-2008] [ 12 –marks]
Given Data :
t
T1 = 870 K ; T3 = 300K
To find : Intermediate Temperature T2
34

Solution : Case (a) Equal work output of Engine
T1=870 K Q1
HEA WA
T Q2
HEB WB
ww T3=300 K Q
w.E
Q1Q2 Q2 Q3

asy
T1  T2 T2  T3
here WA = Q1 - Q2 and WB = Q2 – Q3
En
WA

WB
870  T T  300 gin
here WA=WB so both are cancelled
870 – T = T-300 eer

2 T = 1170 ing
T = 585 K .ne
Case (b) Same efficiency t
T1T T  T3
A  ; B  here  A  B
T1 T
870  T T  300
 870T  T 2  870T  261000
870 300
T2 = 261000  T = 510.88 K
35

3. A heat pump working on a reversed Carnot cycle takes in energy from a

reservoir maintained at 3°C and delivers it to another reservoir where
temperature is 77°C. The heat pump drives power for its operation from
a reversible heat engine operating within the higher and lower
temperature limits of 1077°C and 77°C. For 100kJ/S of energy supplied
to the reservoir at 77°C, estimate the energy from the reservoir at
1077°C. [Nov/Dec-15 / R-2008][ 11 marks]
Given Data:
ww T1=1077+273=1350 K;
w.E
T2=77+273 =350 K = T4
T3= 3+273 = 300 K
asy
Q2+Q4 = 100 kW [kJ/s=kW]
To find : Q1 En
Solution : gin
Efficiency of HE =
eer
COP of HP =
ing
.ne
T1=1350 K T3=276 K t
Q1 Q3
WHE = WHP
HE HP
Q2 +Q4 =100 KJ/S

Q2 Q4
T2= T4 = 350 K
36

Q2 + Q4 = 100 kJ/s [Given in the problem]
Q4 = 100 – Q2
ww
w.E ; [WHP = WHE = 2.8565 Q2]
asy 6.8916 kW ; WHE = 2.8565 Q2 = 19.6589 kW;
En
Q1 = WHE + Q 2 = 26.577 kW
gin
eer
ing
4. A Reversible heat engine operates between two reservoirs at
temperature of 600°C and 40°C. The engine drives a reversible
refrigerator which operates between reservoirs at temperature of 40°C
.ne
and -20°C. The heat transfer to the heat engine is 2000 kJ and the
network output for the combined engine & refrigerator is 360 kJ.
t
Calculate(1) the heat transfer to the refrigerant and the net heat
transfer to the reservoir at 40°C. [Apr/May-15/ R-2013] [ 16 MARKS] (2)
Reconsider (1) given that the efficiency of the heat engine and cop of the
refrigerator are each 40% of their maximum possible value. [Nov/Dec-
14 /R-2008]
Given Data:
37

T1 = 600 + 273 = 873 K,

T2 = 40 +273 =313 K = T4;
T3 = -20 +273 = 253 K;
Q1= 2000 KJ;
WNET = 360 KJ
To find :
Q3 , QRnet = Q2 +Q4
ww T1=873 K T3=253 K
Tips : All four temperatures are known.
w.E Q1 = 2000 KJ
WHE WRE
Q3 Find efficiency of HE and COP of RE
using temperatures.
Wnet = WHE - WRe
HE
asy Wnet = 360 KJ

RE
Q2
En Q4
T2= T4 = 313 K
gin
Case (i) eer
Efficiency of Heat engine ing
=0.642 .ne
Heat rejection by Heat engine t
.
Work output of Heat engine

WHE = Q1-Q2 = 2000-716 = 1284 kJ
Work input of Refrigerator
WNET =WHE – WRE; WRE = 924 kJ
COP of refrigerator
38

Q4 =
Net heat rejected to 40°C reservoir QRnet = Q2 + Q 4 = 5539 kJ
Case (ii)
ww Efficiency of the actual heat engine cycle
  0.4 max  0.4  0.642
w.E
WHE  0.4  0.642  2000  513.6kJ
asy
WRE  513.6  360  153.6kJ
En
COP of the actual refrigeration cycle
COP  0.4  COPmax  0.4  4.22  1.69 gin

eer
Therefore, Q3 = 153.4 x 1.69 = 259.6 kJ
Q4 = 259.6 + 153,6 = 413.2 kJ ing
Q2 = Q1 – WHE = 2000-513.6 = 1486.4 kJ .ne
Net heat rejected to 40°C reservoir QRnet = Q2 + Q 4 = 1899.6 kJ t
5. a. A metal block with m=5kg, C=0.4 kJ/kg K at 40°C is kept in a room at
20°C. it is cooled in the following two ways:
(i) Using a Carnot engine (Executing integral number cycle) with the
room itself as the cool reservoir
(ii) Naturally
39

In each case, calculate the change in entropy of the block, of the air of
the room and of the universe. Assume that the metal block has constant
specific heat. [May/June -2016 / R-2008] [ 8 marks]
Given Data:
m = 5 kg
C = 0.4 kJ/Kg K
T1 = 40 + 273 = 313 K
T2 = 20 + 273 = 293 K
ww
Solution :
(i)
w.E
Cooling Naturally
Heat absorbed by air dQ = Heat released by the metal block

asy
dQ = m C (T1 – T2) = 5 x 0.4 x (40-20) = 40 kJ
En
Entropy Change of the block
gin
ΔSblock =
eer
= 5 x 0.4 ln(293/313) = -0.132 kJ/K ing
Entropy Change of atm. .ne
ΔSair = = 0.1365 kJ/K t
Entropy of universe: Suni = ΔSblock + ΔSair = -0.132 + 0.1365 = 0.0045 kJ/K
(ii) Cooling using Carnot engine
If the metal block cools naturally, heat removed from metal block
dQ = 40 kJ
Entropy of block ΔSblock = -0.132 kJ/K
40

Entropy of Carnot engine ΔSCarnot = 0

For Carnot engine efficiency
= 6.39 %
ww 0.0639 =
w.E W = 2.556 kJ
asy
Entropy of air ΔSair =
En
ΔSair =
gin
= 0.1452 kJ/K
Entropy of universe
eer
ing
ΔSuni = ΔSblock + ΔSCarnot + ΔSair = -0.132 + 0 + 0.1452 = 0.2772 kJ/K
ΔSuni = 0.2772 kJ/K .ne

5.b. 50 kg of water is at 313 K and enough ice at -5°C is mixed with water in
an adiabatic vessel such that at the end of the process all the melts and
t
water at 0°C is obtained. Find the mass of ice required and entropy change
of water and ice. Given Cp=4.2kJ/kg K, Cp of ice = 2.1 kJ/kg K and latent
heat of ice = 335 kJ/kg. [Apr/May-2016/R-2013] [ 8 marks]
Given data:
mw = 50 kg;
Tw = 313 K,
41

Tice = -5 +273 = 268 K;

Final temperature Tf = 0 +273 = 273 K ;
Cpw = 4 .2 kJ/kg K;
Cp ice = 2.1 kJ/kg K;
LH ice = 335 kJ/kg
To find :
(i) mass of ice
(ii) entropy change of water and ice.
ww
Solution:
Heat lost by water = Heat gain by ice.
w.E
Water lost sensible heat from 313 K to 273 K = Ice gain heat (sensible heat
asy
from 268 to 273 K + Latent heat)
En
mw x Cpw x (Tw-Tf) = m ice [(Cp ice (Tf-Tice) + Latent heat]
gin
50 x 4.2 x (313-273) = m ice [(2.1 x (273-268) + 335]
eer
Entropy change of water ing
.ne
t
Entropy change of Ice = Sensible heat + Latent Heat
42

6. a. 2 kg of air at 500 kpa 80°C expands adiabatically in a closed system

until its volume is doubled and its temperature become equal to that the
surrounding at 100 kpa and 5°C. Find maximum work, change in
availability and the irreversibility. [APR/MAY 2015 /R-2013][16 marks]
Given data :
m = 2 kg ;
P1 = 500 kpa;
T1=80+273 = 353 K;
ww V2= 2V1;
T2= T0 = 5 +273 = 278 K,
w.E
P2= P0=100 kPa
asy
To Find : maximum work, change in availability and the irreversibility
Solution :
En
Entropy change of air
gin
eer
kJ/K
ing
.ne
t
Volume
Volume
Change in availability
43

Irreversibility
7.a. 5kg of air at 550 K and 4 bar is enclosed in a closed vessel (i) determine
the availability of the system if the surrounding pressure and temperature
are 1 bar 290 K (ii) If the air is atmospheric pressure cooled at constant
pressure to the atmospheric temperature, determine the availability and
effectiveness. [ NOV/DEC 2014 /R-2013] [10 marks]
ww Give Data :
w.E
m = 5 kg;
T1 = 550 K;
asy
P1 = 4 bar = 4 x 105 N/m2;
T2=T0= 290 K;
P2=P0 = 1 bar=1x 105N/m2. En
To find : Availability and effectiveness
gin
Solution
Case (i) eer
Availability of the system = ing
.ne
. t
Availability of the system
Availability of the system

Case (ii)
44

Heat transferred during cooling
Change in entropy during cooling
Unavailable portion of this entropy
ww
w.E
Available energy = 1306.5 – 932.64 = 373.86 kJ
asy
Effectiveness
En
gin
eer
7.b. A heat engine receives 800 kJ of heat from the reservoir at 1000 K
and rejects 400 kJ at 400 K. If the surrounding is at 300 K. calculate the
ing
first and the second law efficiency, and the relative efficiency of the heat
engine. [Apr/May-2016/R-2013] [ 6 marks]
.ne
Give Data : Q1 = 800 kJ; T1=1000 K; Q2=400 kJ; T2=400 K; T0=300 K t
To find :Ist and IIndlaw efficiency , Relative efficiency
Solution :
Heat engine efficieny
Efficiency of reversible heat engine operating with atmosphere as sink
45

The second law efficiency of heat engine
The efficiency of reversible heat engine
The relative efficiency
ww
w.E
8. A heat pump operates on a carnot heat pump cycle with a COP of 8.7. it
keeps a space at 24oC by consuming 2.15 kw of power. Determine the
asy
temperature of the reservoir from which the heat is absorbed and the heating
load provided by the heat pump.
En NOV/DEC 2016 (7 MARK)
Given data:
gin
Carnot COP of heat pump = 8.7
eer
TH= 24oC = 297 K
ing
Power consumption or work done = 2.15 kw
Solution: .ne
COP of cornot pump =
TH
TH  TL
t
297
8.7 =
297  TL
TL = 262.86 K = -10.14oC
For reversible heat pump,
Actual COP of heat pump = carnot COP of heat pump
46

QH TH
=
QH  QL TH  TL
1 1

Q T
1 L 1 L
QH TH
QL T
1  1 L
QH TH
Q L TL

ww Q H TH
TL
w.E QL 
TH
 QH
asyQL 
262.86 L
297
 QH  0.89QH
But, work done = QH  QL

En
Substituing QL in work done, gin
2.15  QH  0.89QH
eer
 0.11QH
ing
Heating load, QH  19.55kW .
.ne
9. A 30 kg iron block and a 40 kg copper block, both initially at 80 o C. Thermal
equilibrium is established after an while as a result of heat transfer between
t
the blocks and the lake water. Determine the total entropy change for this
process. NOV/DEC 2016 (8 MARK)
Given data:
Miron = 30 kg
Mcopper = 40 kg
Tiron = Tcopper = 80o C =273 + 80 = 353 K

47

Tlake = 15o C = 273 +15 = 288 K
Solution:
CP iron = 0.45 kJ/kgoC = 0.45 kJ/kgK
CP copper = 0.386 kJ/kgoC = 0.386 kJ/kgK

288
dT
Entropy change of iron, iron =
353
m iron C Piron
T
= miron CP iron In T 353

288
ww = 30 x 0.45 In 
 288 
 353 
= -3.14 kJ/K
w.E
Heat absorbed by lake from both blocks,
asy
Q = heat released by iron block + heat released by copper block
En
Q = mironC Piron Tiron  Tlake   mcopperC Pcopper Tcopper  Tlake 
Q = 30 x 0.45(353 – 288) +40 x 0.386(353 – 288) = 1881.1 kJgin

Entropy change of lake, lake = -
Q
=
1881.1
eer
= 6.53kJ/K
Total entropy change,

T 288
ing
+ S copper  S lake  2.75  3.14  6.53
.ne
iron
= 0.64 kJ/K.
10. A heat pump working on the carnot cycle takes in heat from a reservoir at
5 oC and delivers heat to a reservoir at 60 oC. The heat pump is driven by a
t
reversible heat engine which takes in heat from reservoir at 840 oC and rejects
to a reservoir at 60 oC. The reversible heat engine also drives a machine that
absorbs 30 kW. If the heat pump extracts 17 kJ/s from5 oC reservoir,
determine
(i) the rate of heat supply from the 840 oC source, and
(ii) the rate of heat rejection to the 60 oC sink
APRIL/MAY 2017 (13 MARK)
48

Given:
T1 = 840+273 = 1113 K
T2 = 60+273 = 333 K
T3 = 5+273 = 278 K
T4 = 60+273 = 333 K
Q3 = 17kJ/s
W3 = 30 kW
ww
To fond:
w.E
(i)
(ii)
the rate of heat supply from the 840 oC source, and
the rate of heat rejection to the 60 oC sink
Solution:
asy
COPHP 
TH

T4

333
TH  TL T4  T3 333  278 En
 6.055
COPHP 
QS 2

Q4 gin
6.055 
QS 2  QR 2 Q4  Q3
Q4 eer
Q4  17
Q4  20.36 kJ s ing
.ne
t
49

W2  Q4  Q3  20.36  17  3.36 kJ s
W1  W2  W3  3.36  30  33.36kW
Maximum Efficiency of heat engine
TH  TL T1  T2
 max  
TH T1
1113  333
  0.7  70%
1113
W
 max  1
Q1
Q1 
ww W1
 max

33.36
0 .7
 47.66kW
W1  Q1  Q2
w.E
Q2  47.66  33.36  14.3kW
asy
Net heat transferred to the reservoir at 60 oC
 Q2  Q4  14.3  20.36  34.9kW

En
gin
11.An inventor claims to have developed a refrigeration system that removes
eer
heat from the closed region at – 12oC and transfers it to the surrounding air at
25oC while maintaining a COP of 6.5 . is this calm reasonable?
ing
Given data: .ne

TL  12O C  12  273  261K
t
TH  25O C  25  273  298K
COP of refrigerator = 6.5
Solution:
TL 261
COP of carnot refrigerator =   7.05
TH  TL 298  261
50

It is abserved that the actual COP of refrigerator is less than carnot COP. Therefore,
the claim is possible.
12. How much of the 100 kJ of thermal energy at 650 K can be converted to
useful work? Assume the environment to be at 25 oC. NOV/DEC 2016 (5 MARK)
Given data:
Q = 100 kJ
T = 650 K
ww
To = 25o C = 273 + 25 = 298 K
Solution:
w.E
Available energy or useful energy,
asy
A.E  Q  Q
TO  T 
 Q1  O 
T  T 
En
 298 
 1001    54.15kJ .
 650  gin
PART - C eer
ing
13. A quantity of air undergoes a thermodynamic cycle consisting of three
processes. Process 1 – 2 : Constant volume heating from P1 = 0.1 MPa, T1 = 15
oC, V1 =n 0.02 m3 to P2 =0.42MPa. Process 2-3 : Constant pressure cooling. .ne
Process 3-1 : Isothermal heating to the initial state. Employing the ideal gas
model with Cp = 1 kJ/kgK, evaluate the change of entropy for each process.
Sketch the cycle on p-v and T-s coordinates. APRIL/MAY 2017 (15 MARK)
t
Given:
P1 = 0.1 MPa = 0.1 x 103 kN/m2
T1 = 15 oC = 298 K
V1 = 0.02 m3
P2 =0.42 MPa = 0.42 x 103
Cp = 1 kJ/kgK
To Find:
51

1. Change of entropy for each process

2. Sketch on p-v and T-s coordinates
Solution:
ww
w.E
From Ideal gas equation
P1VI = mRT1
asy
m
0.1  10 3  0.02
0.287  298 En
m  0.023kg gin
Process 1-2 : Constant Volume eer
Change in entropy during constant volume process ing
S 2  S1  mCv ln
P 2 
P1
.ne
 0.023  0.718  ln
0.42  10 
3
t
0.1 10 
3
s s
2 1
 0.0256 kJ
K
P P
1 2
T T1 2
0.42  10 3  298
T2 
0.1  10 3
52

T2  1251.6K
Process 2-3 Constant Pressure
P2  P3  0.42  10 3 kN m 2
V2 V3
 T3  T1 ,V1  V2
T2 T3
298  0.02
V3 
1251.6
ww
V3  0.00467m 3
V3 
w.E
S 3  S 2  mCp ln
V2 
asy
 0.023  1  ln
0.00467
0.02
S 3  S1  0.033 kJ K En
Negative Sign indicate there is a decrease in entropy gin
Process 3-1 Constant Temperature eer
S1  S 3  mR ln
V1 
V3 
ing
0.02 .ne
 0.023  0.287 ln
S1  S 2  0.0096 kJ K
0.00467 t
53

UNIT III
PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE
PART - A
1. Define a pure substance (May/June 2016 R 8)
A pure substance is a substance of constant chemical composition (homogeneous)
throughout its mass. It is a one component system. It may exist in one or more
phases. eg. water, ice
2. Define critical temperature and pressure for water.
ww
Critical point is the point in the p-v diagram above which, a liquid upon heating
suddenly flashes into vapour or vapour upon cooling suddenly condenses to liquid.
w.E
There is no distinct transition zone from liquid to vapour and vice versa.
For water
asy
pc = 221.2 bar
tc = 374.5 OC
vc = 0.00317 m3/ kg
En
gin
3. How is the triple point represented in the p-V diagram? (May/June 2016 R
8)
eer
ing
The triple point of a substance is the temperature and pressure at which the three
phases gas, liquid, and solid of that substance coexist in thermodynamic
equilibrium. The triple point is represented as a line in the p-v diagram.
.ne
t
54

4. State the phase rule for pure substance (May/June 2016 R 13)
The Gibbs phase rule describes the degrees of freedom (F) available to describe a
particular system with various phases and species. This will depend on the number
of chemical species, C, and number of phases, P, present. In the absence of chemical
reaction, the Gibbs phase rule is simply:
F=2+C-P
For a pure substance (C=1), the Gibbs phase rule can be applied as follows:
For P=1 F=[2+1-1]=2 ; For P=2  F=[2+1-2] =1; For P= 3 F=[2+1-3] =0
ww
5. Mention the two working fluids used in binary vapour cycle (May/June 2016
R 13) w.E
asy
Mercury and steam is the most commonly used pair or fluid in binary vapour cycle.
Apart from Mercury, Diphenyl ether, Aluminium bromide are also used along with
steam.
En
gin
eer
6. A vessel of 2 m3contains a wet steam of quality 0.8 at 210 OC. Determine the
mass of liquid and vapour present in the vessel. (Nov/ Dec 2015 R 8)
Given: ing
V = 2 m3
x = 0.8
.ne
Find:
T = 210 OC
1. mf 2. mg
t
FORMULAE USED :
m  m f  mg
v  v f  vg
mg
Dryness fraction x 
m
v  v f  x v fg  v f  x [v g  v f ]
55

Vg  v g . m g
V f  v f . mg
V
V v . m m
v
At 210 C, from steam tables,
O
Vg  0.10441 m 3 / kg
V f  0.001173 m 3 / kg
v  v f  x v fg  v f  x [vg  v f ] =0.0837m3/kg
V 2
m   23.89 kg
v 0.0837
ww x
m
g

m
g
 m 19 .11kg 
g
w.E
m 23 .89
m  m f  mg  m f  m  mg  4.77 kg 
asy
7. What is normal boiling point? (Nov/ Dec 2015 R 8)
En
The normal boiling point (also called the atmospheric boiling point or the
gin
atmospheric pressure boiling point) of a liquid is the special case in which the vapor
eer
pressure of the liquid equals the defined atmospheric pressure at sea level, 1
atmosphere.
ing
8. What is reheat Rankine cycle and when is it recommended in a steam power
.ne
plant? What is regeneration in Rankine cycle?
Reheat cycle: In reheat cycle, the steam after expansion in a high pressure turbine t
is brought back to the boiler and reheated by the combustion gasses and then fed
back to the low pressure turbine for further expansion. This increases the mean
temperature of heat addition. Higher the mean temperature higher will be the cycle
efficiency. The purpose of a reheating cycle is to remove the moisture carried by the
steam at the final stages of the expansion process.
56

Regeneration cycle: In regenerative Rankine cycle, the condensate water from the
condenser is heated by the steam extracted from the intermediate stages of turbine
Therefore the feedwater entering the boiler is preheated. This increases the work
output and hence improves the thermal efficiency of the system.
9. What is meant by dryness fraction or quality of steam? What are the

methods of determining the quality of steam. (Apr/May 2015)
Dryness fraction is also known as steam quality. It is defined as the ration of the
ww
mass of steam (vapour) in a mixture of saturated liquid and saturated vapour to the
total mass of the liquid vapour mixture. It is indicated by x.
w.E
Dryness fraction x 
mass of vapour
mass of vapour  mass of liquid

mg
m
where m  m f  mg
asy
The quality of steam can be measured using a throttling calorimeter or an electrical
calorimeter.
En
gin
10. Draw the standard Rankine cycle on p-v and T-s coordinates. (Apr/ May
2015)
eer
ing
.ne
t
Rankine cycle on p-v diagram Rankine cycle on T-s diagram
1. 1- 2 --- Reversible Adiabatic expansion process
2. 2-3 --- Reversible constant pressure heat rejection
3. 3- 4 --- Reversible Adiabatic compression
4. 4 - 1 --- Reversible constant pressure heat addition
1 – wet steam , 1’ – Saturated steam, 1” – superheated steam
57

11. State the advantages of using superheated steam in turbines.(Nov/Dec

2014)
The advantages of using superheated steam in turbines are
1. The mechanical power output can be increased.
2. Thermal efficiency of the system is increased.
3. Small size condenser can be used.
4. Damages caused to by corrosion of turbine blades can be prevented.
ww
12. Draw the p-T and p-v diagram for water or any pure substance and label
all salient points. (Nov/Dec 2014)
w.E
asy
En
gin
eer
p-T diagram for water
ing p-v diagram for water
13. Mention the possible ways to increase the thermal efficiency of Rankine .ne
cycle.(May/June 2014, 2017)
1. Decreasing the condenser pressure
t
2. Increasing the boiler pressure
3. Superheating the steam to a higher temperature
4. Reheating and regeneration in Rankine cycle
14. When will you call a vapour superheated and define degree of superheat,
and when will you call a liquid subcooled or compressed liquid and define
degree of subcooling
58

Superheated steam or vapour: When the temperature of the vapour is greater

than the saturation temperature corresponding to the given pressure, the vapour is
said to be superheated vapour
Degree of superheat: The difference between the temperature of the superheated
vapour and the saturated temperature at that pressure is called degree of superheat
or superheat.
Subcooled liquid or compressed liquid: When the temperature of the liquid is
lower than the saturated temperature corresponding to the given pressure, the
ww
liquid is said to be compressed liquid or subcooled liquid. When the liquid is cooled
below its saturation temperature at a certain pressure it is said to be subcooled.
w.E
Degree of subcool: The difference between the temperature of the compressed
asy
liquid and the saturated temperature at that pressure is called degree of subcool or
subcooling.
En
gin
15. What is a p v T surface? What do you mean by specific steam rate? State its
units
P v T surface: eer
ing
The variables of the ideal gas equation p,v and T are plotted along three mutually
.ne
perpendicular axes. Such a surface is called p-v-T surface. These surfaces represent
the fundamental properties of a substance and provide a tool to study the
thermodynamic properties and processes of a substance.
Specific steam rate:
t
It is defined as the quantity of steam flow required for producing unit power. It is
also known as steam rate (kg/ kW hr). It defines the capacity of the boiler
59

PART B
1. Discuss the different zones of T-s diagram for water when the temperature
rises from -20OC to 200 OC at 1 atm pressure [May/ June 2016 R 8, Nov/Dec
2015] (16 marks)
ww
w.E
asy
En
gin O O
Figure 1 T-s diagram for heating of ice from -20 C to 200 C
eer
ing
.ne
t
Figure 2 T-s diagram for heating of ice from -20OC to 200OC at different pressures
The state changes of water upon slow heating at different constant pressures are
shown on the T-s diagrams at different pressure levels. If the heating of ice at
to steam at at the constant pressure of 1 atm is considered, 1-2 is the solid
(ice) heating, 2-3 is the melting of ice at , 3-4 is the liquid heating upto 100OC, 4-5
60

is the vapourisation of water at 100 , and 5-6 is the heating of vapour phase upto
200OC. The process will be reversed from 6 to state 1 upon cooling. The curve
passing through the 2, 3 points is called fusion curve, and the curve passing through
the 4,5 points (which indicate the vaporisation or condensation at different
temperatures and pressures) is called vaporisation curve. If the vapour pressure of a
solid is measured at different temperatures and these are plotted, sublimation curve
will be obtained. The fusion curve, the vaporisation curve, and the sublimation
curve meet at the triple point.
ww The slopes of the sublimation and vaporisation curves for all substances are
positive. The slope of the fusion curve for most substances is positive, but for water,
w.E
it is negative, The temperature at which a liquid boils is very sensitive to pressure,
asy
as indicated by the vaporisation curve which gives the saturation temperatures at
different pressures, but the temperature at which the solid melts is not such a stong
En
function of pressure, as indicated by the small slope of the fusion curve.
gin
2. A vessel of volume 0.04
eer
contains a mixture of saturated water and
saturated steam at a temperature of 250 . The mass of the liquid present is 9
ing
. Find the pressure, the mass, the specific volume, the enthalpy, the entropy,
and the internal energy. [May/ June 2016 R 8, Nov/Dec 2015, April/May 2017]
.ne
(16 marks)
Given:
t
V = 0.04
T = 250OC
mf = 9 kg
Find:
p, m, v, h, s, u
Solution From steam tables, at 250 , =3.973 Mpa
/ , /
61

Volume of liquid,
Volume of vapour, = 0.04-0.01126 = 0.02874
∴ Mass of vapour
∴ Total mass of mixture,

ww
Quality of mixture,
9+0.575 9.575
w.E 0.06
asy
En
gin
eer
ing
.
.ne
t
4. A large insulated vessel is divided into two chambers one containing 5 kg of
dry saturated steam at 0.2 MPa and the other 10 kg of steam 0.8 quality at 0.5
MPa. If the partition between the chambers is removed and the steam is mixed
62

thoroughly and allowed to settle, find the final pressure, steam quality and
entropy change in the process. [May/ June 2016 R 13] (16 marks)
Given:
ww
w.E
Find: p2, x2 , ds
Solution
asy
The vessel is divided into chambers as shown in above figure
At 0.2Mpa,
En /kg
At 0.5Mpa, gin
eer
ing
.ne
t
Total volume,
Total mass of the mixture,
Specific volume of mixture
63

By energy balance
At 0.2 MPa,
At 0.5Mpa,
ww
w.E
asy
En
Now for the mixture
gin
eer
ing
From the Mollier diagram, with the given values of h and v, point 3 after mixing is
fixed (Fig 9.40)
.ne
t
∴ entropy change during the process (ds)
64

5. In a steam power plant the condition of steam at inlet to the steam turbine
is 20 bar and 300 OC and the condenser pressure is 0.1 bar. Two feed water
heaters operate at optimum temperatures. Determine: (1) the quality of steam
at turbine exhaust (2) network per kg of steam (3) cycle efficiency (4) the
steam rate. Neglect pump work [May/ June 2016 R 13] (16 marks)
Given:
p1 = 20 bar
T1 = 300OC
ww p4 = 0.1 bar
Find: x4, W , steam rate
Solution: w.E
asy
En
gin
eer
ing
.ne
t
Temperature rise per heater =
Temperature at which the first heater operates
65

Temperature at which second heater operates = 157-55 = 102OC = 100OC (approx)
At 0.1 bar,
At 100 ,
At 150
ww
w.E
asy =
En
gin
eer
ing
Since pump work is neglected,
balance for the hp heater
By making an energy
.ne
t
Rearranging
By making an energy balance for the lp heater,
66

∴
ww
w.E
Steam rate
asy
En
6. A steam power plant operates on a theoretical Rankine reheat cycle. Steam
gin
at boiler at 150 bar and 550 OC expands through the high pressure turbine. It
is reheated at a constant pressure of 40 bar to 550 OC and expands through the
eer
low pressure turbine to a condenser at 0.1 bar. Draw the T-s and h-s diagrams,
ing
Find: 1) Quality of steam at turbine exhaust 2) cycle efficiency 3) steam rate in
kg/kW hr [May/June 2014 R 8 April/May 2017] (16 marks)
Given: .ne
P1 = 150 bar
T1 = 550OC
t
P2 = 40 bar
T3 = 550 OC
P4 = 0.1 bar
Find: 1. Quality of steam at exit x 4s
2. Cycle efficiency
3. Steam rate in kg/kW hr
Solution:
67

The property values at different states are read from the Mollier chart.
h1 = 3465 kJ/kg, h2 = 3065 kJ/kg, h3 = 3565 kJ/kg
h4 = 2300 kJ/kg, x4 = 0.88, h5 (steam table) = 191.83 kJ/kg
ww
w.E
asy
Quality at turbine exhaust = 0.88
En
Wp= v p = 10-3 x 150 x150 x 102 = 15 kJ/kg
gin
h6 = 206.83 kJ/kg
eer
Q1 = (h1 – h6) + (h3 – h2)
ing
= (3465 – 206.83) + (3565 - 3065) = 3758.17 kJ/kg
.ne
WT = (h1 – h2) + (h3 – h4) t
= (3465 - 3065) + (3565 - 2300) = 1665 kJ/kg
WNet = WT - Wp = 1665 – 15 = 1650 kJ/kg
wnet 1650
   0.4390  43.9%
Q1 3758 .17
3600 3600
Steamrate   2.18 kg / kWhr
wnet 1650
68

7. Steam initially at 0.3 MPa, 250 OC is cooled at constant volume. At what

temperature will the steam become saturated vapour? What is the steam
quality at 80 OC. Also find what is the heat transferred per kg of steam in
cooling from 250 OC to 80 OC [Nov/Dec 2013 R 8] (16 marks)
Given:
p1 = 0.3 MPa
T1 = 250OC
ww
Find:
1. Tsat when cooled at constant volume
w.E
2. x when cooled to 80OC
asy
3. Q when cooled from 250OC to 80OC
En
gin
eer
ing
.ne
Solution
t
Since the state would be in superheated . From steam table A.2for
properties of superheated steam at 0.3 Mpa, 250
/kg
69

From Steam tables,
When
Therefore, when by linear interpolation, would be 123.9 . Steam

would become saturated vapour at
At /kg,
ww
w.E
∴
asy
En
gin
From the first law of thermodynamics
eer
ing
∴
.ne
Or
t
PART - C
8.A regenerative cycle utilizes steam as a working fluid . Steam is supplied to

the turbine at 40 bar and 4500C and the condenser pressure is 0.03bar. After
70

expansion is the turbine to 3 bar, some of the stream is extracted from the
turbine for heating feed water from the condenser in an open heater. The
pressure in the boiler is 40 bar and the state of the fluid leaving the heater is
saturated liquid water at 3 bar Assuming isentropic heat drop in the turbine
and pumps, compute the efficiency of the cycle. NOV/DEC 2016 (13 MARK)
Given data:
p1 = 40 bar
ww T1 = 4500C
w.E
p2 = 3 bar
asy
p3 = 0.03 bar
To find:
En
Ƞ regenerative
gin
Solution:
eer
From super heated steam table
ing
At p1 = 40 bar and T1 = 4500C
.ne
h1 = 3330.3kJ/kg s1 = 6.9363kJ/kgk t
From saturated steam table, p2 = 3 bar
hf2 = 561.47 KJ/kg hfg2 = 2163.8 kJ/kg
sf2 = 1.68 KJ/kg k sfg2 = 5.320 kJ/kg k
vf2 = 0.001073 m3/kg
At p3 = 0.03 bar
71

hf3 = 101.05 KJ/kg hfg3 = 2444.5 kJ/kg
sf3 = 0.3545 KJ/kg k sfg3 = 8.223 kJ/kg k
vf3 = 0.001003 m3/kg
We know that ,
s1 = s2 = sf2 + x2 * sfg2
= 6.9363 = 1.6718 + x2 * 5.321
ww = 0.9895
w.E
h2 = hf2 + x2 * hfg2
asy = 561.47 + 0.9895 x 2163.8
= 2702.65kJ/kg
En
Simirlarly, gin
s1 = s3 = sf3 + x3 * sfg3 eer
6.9363 = 0.3545 + x3 * 8.2231 ing
= 0.8 .ne
h3 = hf3 + x3 * hfg3 t
= 101.05 + 0.8 * 2444.5
= 101.35kJ/kg
Pump work during 4- 5 processes
Wp4-5 = (1- m) (h5-h4) = (1- m) x vf3 (p2-p3)
h5-h4 = vf3 (p2-p3)
72

= 0.001003(300-3)
= 0.2989 kJ/kg
h5 = 0.29789 + 101.05
= 101.35kJ/kg
Amount of steam bleed
m = hf2 – h5 / h2- h5
ww = 561.47 – 101.35/ 2702.65 – 101.35
w.E = 0.117 kg
asy
Wp6_7 = h7-h6 = vf2 (p1-p2)
En
= 0.001073 ( 4000- 300)
= 3.9701kJ/kg gin
h7 = 3.9701 + h6 = 3.9701 + hf2 eer
= 3.9701 + 561.47KJ ing
= 565.44 kJ/kg .ne
Regenerative rankine cycle efficiency t
Ƞ regenerative =( h1 – h7 ) – (1 – m ) (h3 – hf3 ) / (h1 – h7 )
= (3330.3 – 5654.4) - ( 1- 0.177 ) ( 2057. 63 – 101.05 ) / (3330.3 – 5654.4 )
Ƞ regenerative = 41.75%
73

9.A steam initially contains 5 m3 of steam and 5 m3 of water at 1Mpa. Steam is

taken out at constant pressure until 4 m 3 of water is left. What is the heat
transferred during the process? NOV/DEC 2016 (13 MARK)
Given data:
Vs1 = 5 m3
Vw1 = 5 m3
P = 1 Mpa = 10 bar
ww
Vs2 = 4 m3
Solution:
w.E
From steam tables corresponding to 10 bar,
asy
V f  Vw  0.001127m 3 / kg
Vg  0.1944m 3 / kg En
Vs Vw gin
Initial mass of water and steam, m1  
vs vw
eer

5

5
0.001127 0.1944 ing
 4462.28kg
Vs Vw .ne
Final mass of water and steam , m2 

4

vs vw

6
 3580.11kg
t
0.001127 0.1944
Mass of steam taken out, m  m1  m2  4462.28  3580.11  882.17kg
Making an energy balance,
Initial energy stored in saturatedwater and steam + heat transferred from the
external source = final energy stored in saturated water and steam + energy leaving
with steam.
74

U 1  Q  U 2  m s hg
Corresponding to 1 Mpa = 10 bar
h f  761.68kJ / kg
h fg  2583.6kJ / kg
hg  2778.1kJ / kg
Assuming that the steam is taken at dry condition.
ww
m1w 
Vw

5
v w 0.1944
 25.72kg
Similarly, w.E
m2 w 
Vw

6
v w 0.1944asy
 30.86kg
Final mass of water and steam En

m2 
V s Vw
 
4

6
 3580.11kg
gin
v s v w 0.001127 0.1944
eer
m1h f  m1w h fg  Q  m2 h f  m2 w h fg  mhg ms
ing
 m1 
.ne
4462.28  761.68  25.72  2583.6  Q  3580.11 761.68  30.86  2583.6  882.17  2778.1
Q = 1792104.94 kJ
=1792.11 MJ.
t
75

UNIT IV
IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS
1. Define Avogadro’s law. (NOV/DEC 2013)
Avogadro’s law states that ‘Equal volumes of all perfect gases at the same
temperature and pressure contain equal number of molecules’.
2. What is a real gas? Give example. (NOV/DEC 2013)
The gas which does not obey the law of equation of state is known as real gas. All
practical gases are real gas.
ww
3. Using Clausius-Clapeyrons equation, estimate the enthalpy of vapourization
w.E
at 2000C, vg=0.127m3/kg, vf= 0.001157m3/kg, dp/dT=32kPa/K. (MAY/JUNE
2014)
asy
By Clausius-Clapeyron equation.
En
dp h f g

dT Tvfg gin
dp

hf g
dT T v g  v f 
eer
ing
.ne
hfg =1910.814kJ/kg
t
4. What are the assumptions made to derive ideal gas equation analytically
using the kinetic theory of gases? (MAY/JUNE 2014)
 There is no intermolecular force between particles.

 The volume of the molecules is negligible in compression with the gas.
76

5. What is known as equation of state and when it can be used for engineering
calculations?. (NOV/DEC 2014)
The relationship which exits for the state variables such as pressure, volume and
temperature of the system in equilibrium is called equation of state.
The equation of state for ideal is given by pV= mRT
The equations of state are used in process engineering problems when the operating
pressure is low or temperature is high
6. What are known as thermodynamic gradients? (NOV/DEC 2014)
ww
Thermodynamic gradients are mathematical interrelations which are used to
determine the change in thermodynamic properties ex. Pressure, temperature and
w.E
volume, for the system having constant chemical composition. Thermodynamic
gradients are partial derivatives.
asy
7. What is Joule-Thomson coefficient? Why is it zero for an ideal gas?
(APRIL/MAY 2015)
En
gin
Joule-Thomson coefficient is defined as the change in temperature with change in
pressure, keeping the enthalpy constant. It is denoted by
 T 
  
1 eer
  v   v
 p  h cp T
ing p
We know that the equation of state as

.ne
pV=RT
Differentiating the above equation of state with respect to T by keeping

t
pressure, p constant
 v  R v
 T   p  T
p
It implies that the Joule Thomson coefficient is zero for ideal gas.
77

8. What is the law of corresponding states? (APRIL/MAY 2015)
The law of corresponding states the relation among the reduced properties p r, Tr and
vr. . It can be derived from the various equations of state. This indicates that
deviation from ideal gas behavior for all gases is about the same degree.
9. State Gibbs- Daltons law. (NOV/DEC 2015)
The law states that the pressure of mixture of gases is equal to the sum of the
pressure of individual gas.
10. Write the Clausius- Claperyan equation and label all the variables.
ww
Clausius equation which involves in the relationship between the saturation
pressure, saturation temperature, the enthalpy of evaporation and the specific
w.E
volume of the two phases involved.
asy dp h f g

dT Tvfg
Where, En
dp=change in pressure gin
dT=Change in Temp. eer
hfg=Enthalpy of vaporization
ing
T=Absolute temp
.ne
Vfg=Specific volume of vaporization
11. Define volume expansivity.( MAY/JUNE 2016)

t
Volume expansivity or co-efficient of volume expansion is defined as the change in
volume with change in temperature per unit volume by keeping the pressure
constant.
1  v 
  
v  T 
p
78

12. What are the properties of Ideal gas? (NOV/DEC 2014)
An imaginary gas which obeys the equation of states as PV= RT at all pressures and
temperatures is known as ideal gas. If the pressure of real gas tends to zero or
temperature tends to infinity, the real gas behaves as an ideal gas. In equation of
states, the volume may remains constant or pressure may remain constant. But the
minimum possible temperature is zero Kelvin.
13. State the Vander Walls equation of state. (NOV/DEC 2014)
The Vander walls equation of real gases is given by
ww  p  a
 v 2  v  b  RT
w.E
asy b  RTc / 8 pc
En
pc= Critical pressure, Tc = Critical Temperature
gin
14. State the main reasons for the deviation of behaviour of real gases from
ideal gases. (NOV/DEC 2014)
eer
At high pressure, the gases start to deviate from ideal gas behaviour as
ing
intermolecular forces become significant. This occurs at low temperature as well.
This deviation needs to be taken into account. For accounting this deviation, a factor
.ne
called compressibility is introduced. O, the state equation for real gases is given by.
Pv = ZRT
Z is known as compressibility factor.

t
PART- B
1.Derive the Calusius – Clapeyron equation and discuss its significance.

(NOV/DEC 2013, MAY/JUNE 2016, NOV/DEC 2016)
Clausius-Claperyon equation is a relationship between the saturation pressure,

temperature, the enthalpy of evaporation, and the specific volume of the two phases
involved. This equation provides a basis for calculations of properties in a two-
79

phase region. It gives the slope of a curve separating the two phases in the p-T
diagram.
ww
w.E
asy
The Clausius-Claperyon equation can be derived in different ways. The method
En
given below involves the use of the Maxwell relation.
gin
eer
Let us consider the change of state from saturated liquid to saturated vapour of a
ing
pure substance which takes place at constant temperature. During the evaporation,
the pressure and temperature are independent of volume.
.ne
where, sg = Specific entropy of saturated vapour,
t
sf = Specific entropy of saturated liquid,
vf = Specific volume of saturated vapour, and
vgf = Specific volume of saturated liquid.
80

where s
fg = Increase in specific entropy,
vfg = Increase in specific volume, and
h = Latent heat added during evaporation at saturation temperature T.
This is known as Clausius-Claperyon or Claperyon equation for evaporation of
ww
liquids. The derivative dp/dT is the slope of vapour pressure versus temperature
curve. Knowing this slope and the specific volume vg and vf from experimental data,
w.E
we can determine the enthalpy of evaporation, (h g – hf) which is relatively difficult
to measure accurately
asy
It is also valid for the change from a solid to liquid, and from solid to a vapour. At
En
very low pressures, if we assume vg ~v and the equation of the vapour are taken as
pv = RT, then becomes fg
gin
eer
ing
It may be used to obtain the enthalpy of vaporization. This equation can be
rearranged as follows: .ne
t
Integrating the above equation, we get
81

2. Derive the Maxwell relations and explain their importance in

thermodynamics. (MAY/JUNE,NOV/DEC 2014, NOV/DEC 2013,APRIL/MAY
2015, MAY/JUNE 2016)
The first law applied to a closed system undergoing a reversible process

states that
According to second law,
ww
w.E
Combining these equations, we get
asy
En
The properties h, f and g may also be put in terms of T, s, p and v as follows :
gin
Helmholtz free energy function,
eer
ing
Gibb’s free energy function, .ne
t
Each of these equations is a result of the two laws of thermodynamics. Since
du, dh, df and dg are the exact differentials, we can express them as
82

Above these equations we may equate the corresponding co-efficients. For

example, from the two equations for du, we have
ww
w.E
The complete group of such relations may be summarised as follows :
asy
En
gin
eer
ing
.ne
t
The above equations are known as Maxwell relations.
83

3.Draw a neat schematic of a compressibility chart and indicate its salient

features. (NOV/DEC 2013, MAY/JUNE 2016)
The perfect gas equation is given gy
Pv=RT
But for real gas a correction factor has to be introduced in the perfect gas equation
to take into account the deviation of the real gas from the perfect gas equation. This
factor is known as compressibility facto(Z) and is denoted by
Z=
ww
w.E
asy
En
gin
eer
4. Determine the pressure of nitrogen gas at T=175 K and v=0.00375m3/kg on
the basis of
ing
i. The ideal gas equation of state
.ne
ii. The vandar Waals equation of state.
The Van dar Waals constants for nitrogen are a =0.175m 6kPa/kg2, b=
0.00138m3/kg. (APRIL/MAY 2015, MAY/JUNE 2016)
t
Given data:
Volume, v=0.00375m3/kg
Temp. T=175 K
a =0.175m6kPa/kg2
b= 0.00138m3/kg
Nitrogen Molecular Weight = 28
84

To Find:
i. The ideal gas equation of state

ii. The vandar Waals equation of state.
Solution:
(i). The ideal gas equation of state
pv=mRT
p= mRT/v (R for air is 8314 Nm/kgmolK)
ww R= Ro/M = 8314/28 = 296.92 Nm/kgK
w.E
p=296.92×175/0.00375
p=138.5×105N/m2
asy
En
(ii)The vandar Waals equation of state.
 p  a
 v 2 v  b  RoT gin
v= 28×0.00375 = 0.105 m3/kg-mol
 p  0.175  eer
0.105  0.00138  8314  175
 2 
 0.105  ing
p= 154.83×103N/m2
.ne
5. Derive the entropy equations. (NOV/DEC 2015, MAY/JUNE 2016)
Since entropy may be expressed as a function of any other two properties, e.g.
t
temperature T and specific volume v,
But for a reversible constant volume change
85

Hence, substituting in eqn. we get
ww
This is known as the first form of entropy equation or the first Tds equation.
Similarly, writing
w.E
asy
where
En
gin
Also eer
ing
.ne
t
This is known as the second form of entropy equation or the second Tds equation.
6. One kmol of methane is stored in a rigid vessel of volume 0.6m 3 at 200C.

Determine the pressure developed by the gas by making use of the
compressibility chart. (NOV/DEC 2015, MAY/JUNE 2016)
Given data:
Volume v = 0.6m3
86

Temp. T = 20oC + 273 = 293K
To Find:
Pressure p =?
Solution:
The critical constants of methane are Tc = 190.70 K and Pc = 46.41 bar
Reduced temperature Tr = T/Tc = 293/190.7 = 1.537
To calculate the compressibility factor Z both Tr and Pr values are needed.
ww Reduced Pressure, pr = p/pc = p/46.41
w.E
Pressure developed by the gas, p = 46.41 p r
We know that compressibility factor,

asy Z = p v/RT
En
Z = 46.41×105 ×Pr ×0.6/1000 × 8.314 × 293
Z = 1.143Pr gin
eer
The corresponding compressibility value is read from chart which is taken as
0.93 at intersection point.
Pressure, p = ZRT/v
ing
P = 1000 × 0.93 × 8.314 × 293/ 0.6 .ne
P = 3.778MPa t
7. Deduce the expression for Joule Thomson co efficient and draw the
inversion curve. (NOV/DEC 2014, NOV/DEC 2016)
Let us consider the partial differential co-efficient (∂T/∂P)h We know that if a fluid is
flowing through a pipe, and the pressure is reduced by a throttling process, the
enthalpies on either side of the restriction may be equal.
The throttling process is illustrated in Fig. 7.3 (a). The velocity increases at the
restriction, with a consequent decrease of enthalpy, but this increase of kinetic
87

energy is dissipated by friction, as the eddies die down after restriction. The steady-
flow energy equation implies that the enthalpy of the fluid is restored to its initial
value if the flow is adiabatic and if the velocity before restriction is equal to that
downstream of it. These conditions are very nearly satisfied in the following
experiment which is usually referred to as the Joule-Thomson experiment.
ww
w.E
asy Joule Thompson coefficient
En
By keeping the upstream pressure and temperature constant at p1 and T1, the
gin
downstream pressure p2 is reduced in steps and the corresponding temperature T2
eer
is measured. The fluid in the successive states defined by the values of p2 and T2
must always have the same value of the enthalpy, namely the value of the enthalpy
ing
corresponding to the state defined by p1 and T1. From these results, points
representing equilibrium states of the same enthalpy can be plotted on a T-s
.ne
diagram, and joined up to form a curve of constant enthalpy. The curve does not
represent the throttling process itself, which is irreversible. During the actual t
process, the fluid undergoes first a decrease and then an increase of enthalpy, and
no single value of the specific enthalpy can be ascribed to all elements of the fluid. If
the experiment is repeated with different values of p1 and T1, a family of curves
may be obtained (covering a range of values of enthalpy) as shown in figure. The
slope of a curve at any point in the field is a function only of the state of the The
slope of a curve in figure shown above at any point in the field is a function only of
the state of the fluid, it is the Joule-Thomson co-efficient μ, defined by μ =(∂T/∂P)h
88

The change of temperature due to a throttling process is small and, if the fluid is a
gas, it may be an increase or decrease. At any particular pressure there is a
temperature, the temperature of inversion, above which a gas can never be cooled
by a throttling process. Both cp and μ, as it may be seen, are defined in terms of p, T
and h. The third partial differential co-efficient based on these three properties is
given as follows :
ww
w.E
μ may be expressed in terms of Cp, p, v and T as follows :
The property relation for dh is dh = T ds + v dp
asy
From second T ds equation, we have
En
gin
eer
For a constant enthalpy process dh = 0. Therefore,
ing
.ne
t
89

Therefore, if an ideal gas is throttled, there will not be any change in temperature.
Let h = f(p, T)
ww
w.E
asy PART - C
En
gin
8.One kg of CO2 has volume of 1 m3 at 100o C. compute the pressure by
 Vander waal’s equation

 Perfect gas equation eer
ing
The vander waal’s constant a = 362850 Nm4/(kg-mol)2 and b
=0.0423m3/(kg-mol).
.ne
NOV/DEC 2016
Given
Mass, m =1 kg
t
Volume, V = 1 m3
Temperature, T = 100oC =273+100=373K
a = 362850 Nm4/(kg-mol)2
b =0.0423m3/(kg-mol)
solution
90

 Vander waal’s equation
Molar mass of CO2, M = 12 +16 x 2 =44 kg/kmol
Molar specific volume, v =1x44 = 44 m3/kgmol
 a
Vander equation  P  v  b  =RT
 v2 
 362850 
P  44  0.0423  8314  373
 44 2 
wwP = 70360.45 N/m2
 Perfect gas equation
Pv = RT w.E
p
RT
v asy
p
8314  373 En
44
gin
P = 70480.05N/m2.
eer
Write the berthelot and dieterici equations of state.
1. Berthelot equation of state ing

 a 
 p  2 v  b  =RT .ne
 v T
2. First dielerici equation of state
a
pv  b   RTe RT
v
t
3. Second dieterici equation
 
 
v  b   RT
a
p 5
 
 v3 
Where a and b are constant
P = pressure
V =volume
R =gas constant, T = temperature.
91

UNIT-V
GAS MIXTURES AND PSYCHROMETRY
PART-A
1. Define dew point temperature. (Nov/Dec 2015) ,(May/June 2009)

It is the temperature at which condensation of water vapour present in moist
air just begins. Difference between the dew point temperature and dry bulb
temperature is called Dew point depression.
ww
2. What is chemical dehumidification? (Nov/Dec 2015)
w.E
Many salts and liquids are hygroscopic in nature and liberate heat during
adsorption or absorption of moisture from air. Such chemicals can be used for
asy
dehumidification and heat of air in insulated chamber. This process is known as
Chemical dehumidification.
En
gin
3. Define adiabatic saturation temperature.(May/June 2014), (May/June
2009)
eer
The temperature at which the air attains the saturation point, when thermal
ing
equilibrium exists with respect to water , water vapour is known as adiabatic
saturation temperature.
.ne
4. What is by-pass factor? (May/June 2014)
The by-pass factor is defined as the ratio of the difference between the mean
t
surface temperature of the coil and having air temperature to the difference
between the mean surface temperature and the entering air temperature.
5. Why do wet clothes dry in the sun faster? (Nov/Dec 2013)

The heat energy from the sun and the humidity in the air helps the dry cloth to
dry faster.
92

6. Define degree of saturation. (Nov/Dec 2013)
It is the ratio of the mass of water vapour associated with unit mass of dry air to
the mass of water vapour associated with saturated unit mass of dry saturated
air.
7. What is the relative humidity of air if the DPT and DBT are 25°C and 30°C
at 1 atmospheric pressure? (Nov/Dec 2012)
For the given data
ww DPT =25°C
DBT=30°C
w.E
P = 1 atm
asy
From the psychometric chart
Relative humidity = 74.48%
En
gin
8. What is adiabatic evaporative cooling? (Nov/Dec 2012)
If unsaturated air is passed through a spray of continuously recirculated water,
eer
the specific humidity will increase while the dry bulb temperature decreases.
ing
This is the process of adiabatic saturation or evaporative cooling
9. Define mass fraction.

.ne
Mass fraction of individual constituents of a mixture is defined as the ratio of
mass of a given constituent to the mass of the whole mixture.
t
10. What is meant by volume fraction?
It is the ratio of number of moles of each constituent gas to the total number of
moles of the gas mixture.
11. State the Gibbs law.

It states that the internal energy, enthalpy and entropy of a gaseous mixture are
respectively equal to the sums of the internal energies, enthalpies and
entropies of the constituents
93

12. Define ‘Mole fraction’.
It is the ratio of the number of moles of each constituent gas to the total number
of moles of the gas mixture.
PART-B
1. The sling psychrometer in a laboratory test recorded the following

readings.
Dry bulb temperature = 35 °C
ww Wet bulb temperature = 25 °C

Calculate the following
(i) w.E
Specific humidity
asy
(ii) Relative humidity
(iii) Vapour density in air
(iv) Dew point temperature
En
(v) Enthalpy of mixture per kg of dry air.
gin
Take atmospheric pressure = 1.0132 bar
eer (Nov/Dec 2015)
Given data:
ing
DBT =35°C
.ne
WBT = 25 °C
Atmospheric pressure = 1.0132 bar t
To find:
(i) Specific humidity

(ii) Relative humidity
(iii) Vapour density of air
(v) Enthalpy of mixture per kg of dry air.
94

Solution:
Partial pressure of vapour, using the equation
Pv =( P vs) wb –
Corresponding to 25 °C ( from steam tables)

(P vs) wb = 0.0317 bar
ww Substituting the values in the above equation, we get
w.E
Pv =0.0317 –
asy
En
= 0.0317 – 0.0065 = 0.0252 bar

gin
W= = eer
= 0.01586 kg/ kg of dry air
ing
(ii) Relative humidity .ne
φ = = = 0.447 = 44.7% t
(iii) Vapour density
PvVv = mv RvTv
Pv = RvTv
= ρ v R v Tv
95

Pv =
Corresponding to 0.0252 bar, from steam tables
Tdp = 21 + (22-21) x
= 21.2°C
(v) Enthalpy of mixture per kg of dry air, h
ww h= Cptdb + W hvapour
w.E = 1.005 x 35 + 0.01586[hg + 1.88 (tdb

= 35.175 + 0.01586 [2565.3 + 1.88 [35- 21.2]
- tdp )
asy Where hg = 2565.3 kJ/kg corresponding to 35°C (Tdb)
En
= 76027 kJ/kg of dry air gin
eer
2. An air–water vapour mixture enters an air conditioning unit at a pressure of
ing
1.0 bar 38°C DBT and a relative humidity of 75 %. The mass of dry air entropy
is 1 Kg/Sec. The air vapour mixture leaves the air-conditioning unit at 1.0 bar,
18°C, 85% relative humidity. The mixture condensed leaves at 18°C. .ne
Determine the heat transfer rate for the process.
Given data :
(May/June 2014)
t
P1 = 1 bar,
Td1 = 38° C
m = 1 kg/Sec
P2 = 1 bar
96

To find :
Heat transfer rate Q = ?

Solution:
For the dry air at 38°C and 75% relative humidity is shown on the
psychometric chart at point 1. The dry air (i.e.) 18°C DBT and 85% relative
humidity is marked on the psychometric chart at point 2.
ww
w.E
asy
En
gin
eer
 Join the point 1 and 2. ing
Enthalpy at point 1 .ne
h1 = 122 KJ/Kg
t
Enthalpy at Point 2
h2 = 45 KJ/Kg
Heat added Q = m (h1 – h2)

= 1 x (122 -45) = 77 KW
97

3. It is required to design an air conditioning system for an industrial process

for the following hot and wet summer conditions. Outdoor condition 32°C DBT
and 65% RH. Required indoor condition 25°C and 60% RH. Amount of free air
circulated 250m3/min coil dew temperature 13°C. The required condition is
first achieved by first cooling and de-humidifying and then by heating.
Calculate the following with the use of psychometric chart
(i) Cooling capacity of the cooling coil
(ii) Heating capacity of the heating coil in kW and surface
ww temperature of the heating coil if the by-pass factor is 0.3

(iii) Mass of water vapour removed per hour. (May/June 2014)
w.E
Given data
asy
Outdoor condition : DBT = 32° C, RH = 65%
Indoor condition : DBT = 25° C, RH = 60%.
DPT = 13 ° C En
To find:
gin
(i)
(ii) Heating eer
Cooling capacity of the cooling coil
capacity of the heating coil in kW and surface
ing
temperature of the heating coil if the by-pass factor is 0.3
(iii) Mass of water vapour removed per hour.
.ne
Solution:
t
98

 Locate the points 1,5 and 3 on the psychometric chart

 Join the line 1-5
 Draw constant specific humidity line through 3 which cuts the line 1-5 at
point 2
From psychometric chart
h1 = 82.5 kJ/Kg, h2 = 47.5 kJ/Kg, h3 = 55.7 kJ/Kg, h4 = 36.6 kJ/Kg
ω1 = 19.6 gm/kg, ω3 = 11.8 gm/kg,
ww DBT2 = 17.6° C Vs1=0.892 m3/kg
w.E
Mass of air supplied per minute = ma = = 280.26kg/min
asy
(i)Capacity of the cooling coil
=
En
= gin = 42.04 kW
eer
By –pass factor of the cooling coil is given by
ing
B.F = = = 0.237
.ne
(ii)Heating capacity of the heating coil
t
= ma (h3-h2)
= 280.26 (55.7 – 47.5)
= 2298.13 kJ/min
= = 38.3 kW
99

By –pass factor of the heating coil is given by
B.F =
0.3 =
= 28.2 ° C
(iii) Mass of water removed per hour
ww =
w.E =
asy = 131.16 kg/h
En
4. Atmospheric air at 1.0132 bar has 20°C DBT and 65% RH. Find the humidity
gin
ratio, wet bulb temperature, dew point temperature, degree of saturation,
enthalpy of the mixture, density of air and density of vapour in the mixture
(Nov/Dec 2012) eer
Given data
ing
Pb = 1.0132 bar, DBT = 20°C , RH = 65%
.ne
To find:
(i) humidity ratio

t
(ii) wet bulb temperature
(iv) dew point temperature,
(v) degree of saturation ,
(vi) enthalpy of the mixture,
(vii) density of air
(viii) density of vapour in the mixture
100

Solution:
From steam tables corresponding to 20°C
Ps = 0.02337 bar
Humidity ratio
0.65 =
ww Pv = 0.0151 bar
Pb=Pv +Pa
w.E
1.132 = 0.0151 +Pa
asy
Pa = 0.998 bar
Specific volume of air

En
Va =
gin
Ra = 0.287 kJ/kg, Ta = td +273
eer
Ta =20+273 = 293
ing
Pa = 0.0151 x 293 =4.45 bar
.ne
Va =
Dew point temperature (Tdp)

= = 0.842 m3/ kg
t
For Pv = 0.0151 bar from steam tables
Tdp = 13°C
Specific humidity ( ) = 0.622
0.622 x = 0.00941 kg/ kg of dry air
101

Degree of saturation
= =
= 0.64
Density of air in the mixture Pa Va = Ra Ta
Pa = =
ww Pa =1.187kg/m3
Density of vapour in the mixture
w.E
Pv Vv = Rv Tv
asy
0.0151 x 102 Vv = 0.0462 x 293
Vv = 89.64 m3/kg
En
= 0.0111 kg/m3
gin
eer
5.Two streams of moist air , one having flow rate of 3 kg/sec at 30°C and 30 %
relative humidity, other having flow rate of 2 kg/sec at 35°C and 65% relative
ing
humidity get mixed adiabatically. Determine specific humidity and partial
pressure of water vapour after mixing. Take C p for stream = 1.86 kJ/kg K
.ne
(April/May 2011)
Given data t
m1 = 3 kg/sec m2 = 2 kg/sec
DBT 1 = 30°C , 1= 30%
DBT2 = 35°C 2 = 65%

To find
(ii) Partial pressure of water vapour after mixing
102

Solution:
For adiabatic mixing
m1= 3 kg/sec m2 = 2 kg/sec
By using DBT1= 30°C and =30% from psychometric chart
= 0.008 kg moisture/ kg dry air
ww
By using DBT2= 35°C 1 = 0.024 from psychometric chart
w.E
=  1.5 =
asy= 0.0144 kg moisture/ kg dry air
En
The specific humidity after mixing = 0.00144 kg/kg of dry air
Vapour pressure (Pv) from gin

is found out from the Psychometric chart
Pv = 16.5 mm of Hg eer
760 mm of Hg = 1.013 bar
ing
Partial pressure of water vapour = 0.02189 bar
.ne
6. Two vessels, A and B, both containing nitrogen, are connected by a
valve which is opened to allow the components to mix and achieve an
t
equilibrium temperature of 27 . Before mixin g the following
information is known about the gases in two vessels.
Vessel A Vessel B
P = 1.5 MPa P = 0.6 MPa
T = 50 T =20
Contents = 0.5 kg mol Contents = 2.5 kg mol
103

Calculate the final equilibrium pressure, and the amount of heat transferred
to the surroundings. If the vessel had been perfectly insulated, calculate the
final temperature and pressure which would have been reached. Take γ=1.4
Given data: γ=1.4
Vessel A Vessel B
ww P = 1.5 MPa
T = 50
P = 0.6 MPa
T =20
w.E
Contents = 0.5 kg mol Contents = 2.5 kg mol
‘To find:
asy
(i)
En
Final equilibrium pressure
(ii) Amount of heat transferred
gin
Solution :
eer
For the gases in vessel A
ing
PA VA = mARTA
.ne
Where VA is the volume of vessel A
1.5 x 103 x VA = 0.5 x 8.3143 x 323

t
VA = 0.895 m3
The mass of gas in vessel A

mA = nA A
= 0.5 kg mol x 28 kg/kg mol = 14 kg

Characteristic gas constant R of nitrogen
104

R= = 0.297 kJ/kgK
For the vessel B
PB VB = mBRTB
0.6 X 103 x VB = 2.5 x 0.297 x 293
VB = 0.363 m3
ww
Total volume of A and B
w.E
V = VA +VB = 0.895 +0.363
Total mass of gas (m)

= 1.258 m3
asy
m = mA + mB = 14 +2.5 = 16.5kg
En
Final temperature after mixing
gin
T = 27 + 273 =300 K
eer
For the final condition after mixing
ing
PV =mRT
.ne
where P is the final equilibrium pressure
P x 1.258 = 16.5 x 0.297 x 300

t
P=
= 1168.6 MPa
Cv = = = 0.743 kJ/kg K
Since there is no work transfer, the amount of heat transfer
105

Q = change in internal energy
= U 2 – U1
Measuring the internal energy above the datum of absolute zero ( at T = 0 K,

u = 0 kJ/kg)
Initial internal energy U1 = mACvTA + mB CvTB
= (14 x 323 +2.5 x 293) x 0.743
= 3904.1 kJ
ww
Final internal energy U2(after mixing ) = mcvT
w.E = 16.5 x 0.743 x 300
asy = 3677.9 kJ
En
Q = 3677.9 – 3904.1 = - 226.2 kJ
If the vessels were insulated gin

U1 =U2 eer
mAcV TA + mBcV TB = m cV T ing
where T would have been the final temperature .ne
T=
t
= = 318.5 K
T = 45.5 C
The final pressure; P = = = 1240.7 kPa = 1.24 MPa
106

7. A mixture of ideal gases consist of 3 kg of nitrogen and 5 kg of carbon

dioxide at a pressure of 300K Pa and a temperature of 20 .Find (a) the mole
fraction of each constituents, (b) the equivalent molecular weight of the
mixture (c) The equivalent gas constant of the mixture (d) the partial pressure
and partial volumes, (e) the volume and density of the mixture and (f) the cp
and cv of the mixture.
If the mixture is heated at constant volume to 40 , find the changes in thev
ww
internal energy, enthalpy and entropy of the mixture. Find the changes in
internal energy, enthalpy and entropy of the mixture if the heating is done at
w.E
constant pressure. Take γ for co2 and N2to be 1.28 and 1.4 respectively.
asy
Given data:
P= 300kPa
En
T= 20 ,
gin
γ for CO2 = 1.28
eer
γ for N2 = 1.4
ing
To find: .ne
(a) The mole fraction of each constituents,
(b) The equivalent molecular weight of the mixture

t
(c) The equivalent gas constant of the mixture
(d) The partial pressure and partial volumes,
(e) The volume and density of the mixture and
(f) The cp and cv of the mixture.
107

(g) changes in internal energy, enthalpy and entropy of the mixture if the
heating is done at constant pressure
Solution:
(a)Since mole fraction Xi =
XN2 = = 0.485
ww XCO2 = = 0.515
w.E
(b) Equivalent molecular weight of the mixture
asy
M = x1 1 + x2 2
= 0.485 x 28 x+0.515 x 44 En
= 36.25 kg/kg mol
gin
eer
( c ) Total mass
ing
m = m N2 + mCO2 = 3+5=8 kg
.ne
(d)Equivalent gas constant of the mixture
t
R=
= 0.229 kJ/kg K
108

= p = 0.485 x 300 = 145.5 kPa
= p = 0.515 x 300 = 154.5 kPa
= = = 0.87 m3
V = = = 0.923 m3
ww
(e) Total volume of the mixture
w.E
V= = =
asy
V= = 1.79m3
En
Density of the mixture
gin
= + = = eer
ing
= 4.46 kg/m3
.ne
C PN2 – CvN2 = RN2
CvN2 = =
t
= 0.742 kJ/kg K
CpN2 = 1.4 x 0.742
= 1.039 kJ/kg K
For CO2 = = 1.286
109

CvCO2 = = = 0.661 kJ/kg K
CpCO2 = 1.286 x 0.661 = 0.85 kJ/kg K

For the mixture
Cp =
= 3/8 x 1.039 + 5/8 x 0.85 = 0.92 kJ/kg K
ww Cv =
w.E= 3/8 x 0.742 + 5/8 x 0.661 = 0.69 kJ/kgK
asy
If the mixture is heated at constant volume;
U2 – U1 = mCv (T2 – T1)

En
gin
= 8 x 0.69 x ( 40-20) = 110.4 kJ`
H2-H1 = mCp (T2 – T1)

eer
= 8 x 0.92 x 20 =147.2kJ
ing
S2 - S1 = mCvln = mR ln
.ne
= mCvln = 8 x 0.69 x ln t
= 0.368 kJ/kg K
If the mixture is heated at constant pressure and will remain the same.
The change in entropy will be
S2- S1 = mCPln - mR ln
110

= mCPln - 8 x 0.92 ln
= 0.49 kJ/ K
8. An air conditioning system is designed under the following conditions:
Outdoor conditions 150C DBT and 100C WBT
Required conditions 200C DBT and 50% RH
ww Amount of free air circulated 0.25 m3/min person
w.E
Seating capacity – 50 persons
The required condition is achieved first by heating and then by adiabatic
asy
humidifing . Determine the following
En
1. Capacity of heating coil in kw
2. Capacity of humidifier gin NOV/DEC 2016 (13 MARK)
Given data: eer

Dry bulb temperature td1 = 150C ing
Wet bulb temperature tw1 = 100C .ne
Required Indoor conditions:
t
Dry bulb temperature td1 = 200C
Relative humidity, ɸ2 = 50%
v = 4.17x10-3 m3/s /person
Seating capacity = 50 persons
So, amount of free air circulated , V = 4.17x10-3 X 50 = 0.21 m3/s
111

Solution:
Step 1:
Outdoor conditions of air i.e 150C dry bulb temperature 100C wet bulb
temperature are marked on the psychrometric chart at point 1. The required indoor
conditions of air 200C dry bulb temperature and 50% relative humidity is marked
outdoor the psychrometric chart at point 2.
Step 2:
ww
Draw and inclined line through point to along constant wet bulb temperature till its
w.E
cut total enthalpy line. Draw a horizontal line from point 2both the intersect at point
3.
asy
En
gin
eer
ing
.ne
t
Step3:
From psychrometric chart,
h1 = 30kJ/kg
h2 = h3 =40KJ/Kg
w1 = w3 = 0.0055kg/kg of dry air
112

w2 = 0.0075 kg/kg of dry air
ww
w.E
asy
En
gin
eer
ing
.ne
t
Specific volume passing through point 1 is 0.85m3/kg
113

i,e v1 = 0.85m3/kg
ma= V1/v1 = 0.210.835 = 0.25kg/s
Heating coil capacity = ma (h3-h1)
(i,e 1-3 line , dry bulb temp increases)
= 0.25(40-30) = 2.5kw
Capacity of humidifier = ma (w2-w1)
ww =0.25(0.0075-0.0055) = 5x10-4kg/s
w.E PART - C
asy
9.How do you minimize the energy consumed by your domestic refrigerator?
En NOV/DEC 2016 (7 MARK)
gin
 The compressor in the refrigerator is the most power consuming part but itb
is not always on. The fan on the other hand is switches on fequently and
consumes more power.
eer
 The temperature adjustment and the air temperature in the roomdetemines
ing
the dutycycle of refrigerator. So, the power consumption in the refrigerator
will be high in summer season and if it is kept in kitchen.
 Use a double door refrigirator because the freezer compartment is not
.ne
opening frequently. When it open frequently, there will be more power
consumption. So, keep the freezer clean and remove the old food items from
it.
t
 Set the temperature wisely. There are mainly 3 temperature adjustments for
the seasons. Normal, cold and summer seasons. Set the knob accordingly.
 Check the gasket. It is the rubber lining on the door. If it is loose or broken
fridge wil switch on continuously because the temperature inside rises.
 Keep the refrigerator in a well-ventilated areawith minimum 30cm gap from
the wall.
 Clean the compressor and coil once in a month. Unplug the refrigerator, and
turn it. Use a vacuum cleaner or brush to remove dust that accumulated.
114

 Voltage drop is the most common cause of increased power consumption in

fridge. When the voltage drops current use increases. So, check the line
voltage.
 Temperature of the food to be stored. Always cool hot food to room
temperature before storing in the fridge/freezer as hot food would take in the
cold air from the fridge/freezer causing the unit to work harder in order to
maintain its temperature.
 Do not stuff the refrigerator full as it will hinder the flow of cold air thereby
decreasing its efficiency. Adequate space will increase the cooling effficiency
of the refrigerator.
ww Keeping the vegetables in polythene bags will reduce the job of fridge because
there will be some cold air inside the bag. Which keeps the vegetables fresh.
w.E
 Even though stabilizer is a must for fridge, it also takes current considerably.
 Unless you have noticeable condensation, keep power-saver switch on the
asy
energy –saving seting.
 Do not open refrigerator door unneccessarily as every time it is opened, some
En
heat enters which decreases its efficiency.
 Always cover any liquids kept in the refrigerator as moisture lost from the
liquids can impact condenser performance.
gin
 Make sure that the refrigerator remains tightly closed when not open. Any
eer
open space will cause heat to get into the refrigerator causing motor to work
harder thereby consuming more electricity.
ing
10.The interior lighting of refrigerators is provided by incandescent lamps
whose switches are actuated by the opening of the refrigerator door. Consider .ne
a refrigerators whose 40 W light bulb remains on continuously as a result of
performance of 1. 3 and the cost of electricity is Rs. 5 per kWh, determine the
t
increase in the energy consumption of the refrigerator and its cost per year if
the switch is not fixed. Assume the refrigerator is opened 20 times a day for an
average of 30 s. NOV/DEC 2016 (8 MARK)
Given data:
Heat to be removed,Q = 40 W
COP = 1.3
115

Cost of electricity = Rs. 5 per kWh
The refrigenator is opned 20 times a day for an average of 30 s
Solution:
COP of refrigerator =
1.3 =
Power input = 30.77 W
ww
Total power cosumed by the refrigerator = 30.77 +40 =70.77 W
w.E
Total number of hours in a year = 365 x24 = 8760 hrs.
Assume the refrigerator is opened 20 times a day for an average of 30 s.
asy
So, normal operating hours in a year =
En
Extra hours of light on due to malfunction,
gin
= 8760 – 60.83 = 8699.17 hrs
Increase in power consumption = eer

* 8699.17
=615.64 kwh/year ing

Increase in cost of power consumption = 615.64 x 5 = Rs. 3078.20 kw. .ne
13. A household refrigerator that has a power input of 450 W and a COP of
1.5 is to cool 5 lage watermelons, 10 kg each, to 8o C. if the watermelons
t
are initially at 28oC, determine how long it will take for the refrigerator to
cool them. The watermelons can be treated as water whose specific heat is
4.2 kj/kg k. is your answer realistic or optimistic? Explain.
116

Given
Power input,P = 450W
COP = 1.5
No. of watermelons, N =5
Mass of watermelons, m = 10kg
Ti  28o C  273  28  301K
T f  8o C  273  8  281K
ww
Solution
w.E
Heat removed from watermelons, Q  NmC pwater Ti  T f 
asy  5  10  4.2301  281  4200kJ
COP of refrigerator 
refrigerat ioneffect
powerinput En
1.5 
refrigerat ioneffect gin
450
eer
Refrigeration effect = 675 W =675 kJ/min
ing
Time to cool watermelons, t 
heatremoved
refrigerat ioneffect .ne

4200
675
 6.22 min t
Approximation is an under estimate primarily because of assuming uniform cooling
of watermelon, ideal process with no heat transfer, ideal source and sink.
117

B.E/B.Tech. DEGREE EXAMINATION, APRIL/MAY 2017.
Third Semester
Mechanical Engineering
ME 6301 – ENGINEERING THERMODYNAMICS
(Common to Automobile Engineering, Mechanical and Automation Engineering)
(Regulations 2013)
Time : Three hours Maximum : 100 marks
ww Answer ALL questions.
w.E PART A – (10 x 2 = 20 marks)
1. State and explain the Zeroth law and its application.(P3, Q9)
asy
2. Apply steady flow energy equation for a nozzle and state the assumptions
made.
En
3. What is PMM2 and why is it impossible?
gin
4. What do you understand by high grade energy and low grade energy?
5. What are compressed solid and compressed liquid?
eer
6. What are the methods for improving the performance of the Rankine
cycle?(P58, Q13)
ing
7. What is meant by generalized compressibility chart? And what are its
features?
8. What is the value of Joule – Thomson coefficient for an ideal gas? .ne
Why?(P77,Q7)
9. State and prove the Amagats law of partial volume.
10.What is sensible cooling?
t
PART B – (5 x 13 = 65 marks)
11 (a) A gas occupies 0.3 m 3 at 2 bar. It executes a cycle consisting of

processes:
(i) 1 - 2, constant pressure with work interaction of 15kJ
118

(ii) 2 - 3, compression process which follows the law pV = C and U 3 =

U2 and
(iii) 3 - 1, constant volume process, and reduction in internal energy

is 40kJ
Neglecting the changes in Kinetic energy and Potential energy.

Draw pV diagram for the process and determine net work
transfer for the cycle. Also show that first law is obayed by the
cycle. (P17, Q8)
Or
ww (b) In a gas turbine, the gases enter the turbine at the rate of 5 kg/s with a
w.E
velocity of 50 m/s and the enthalpy of 900 kJ/kg and leaves the turbine
with 150 m/s and the enthalpy of 400 kJ/kg. The loss of heat from the
asy
gas to the surroundings is 25 kJ/kg. Assume R = 0.285 kJ/kg K, Cp =
1.004 kJ/kg K and the inlet conditions to be at 100 kPa and 27 oC.
En
Determine the work done and diameter of the inlet pipe.(P 18, Q9)
12 (a)
gin
A heat pump working on the carnot cycle takes in heat from a reservoir
at 5 oC and delivers heat to a reservoir at 60 oC. The heat pump is driven
eer
by a reversible heat engine which takes in heat from reservoir at 840 oC
and rejects to a reservoir at 60 oC. The reversible heat engine also
ing
drives a machine that absorbs 30 kW. If the heat pump extracts 17 kJ/s
from5 oC reservoir, determine
(i) the rate of heat supply from the 840 oC source, and .ne
(ii) the rate of heat rejection to the 60 oC sink (P46 , Q8)
Or
t
(b) Air flows through an adiabatic compressor at 2 kg/s. The inlet
conditions are 1 bar and 310 K and the exit conditions are 7 bar and
560 K. Compute the net rate of energy transfer and the irreversibility.
Take To = 298 K
13 (a) A vessel of volume 0.04 m 3 contains a mixture of saturated water and

saturated steam at a temperature of 250 oC. The mass of the liquid
119

present is 9 kg. Find the pressure, the mass, the specific volume, the
enthalpy, the entropy, and the internal energy. (P61, Q2)
Or
(b) A reheat Rankine cycle receives steam at 35 bar and 0.1 bar. Steam
enters the first stage steam turbine 350 oC. If reheating is done at 8 bar
to 350 oC; calculate the specific steam consumption and reheat Rankine
cycle efficiency. (P67, Q6)
14 (a) 10 kmol of methane gas is stored in 5 m+ container at 300 K. Calculate

the pressure by
ww (i) ideal gas equation and
w.E
(ii) van der Waals equation.
Use the following constants a = 228.296 kPa.m 6/kmol2 and b =
asy 0.043 m3/kmol for the Vander Waals equation.
(b) En Or
The latent heat of vaporization at 1 bar pressure is 2258 kJ/kg and the
gin
saturation temperature is 99.4 oC. Calculate the saturation temperature
at 2 bar pressure using Clausius – Layperyon equation. Verify the same
from the steam table data.
eer
15. (a)
ing
Atmosphere air at 101.325 kPa and 288.15 K contains 21% oxygen and
79% nitrogen, by volume. Calculate the
(i) mole fractions, mass fractions and partial pressures of oxygen
and nitrogen and .ne
(ii) molar mass, gas constant and density of air.
Take Molar mass of oxygen and nitrogen as 32 and 28 kg/kmol.
Or
t
(b) Air at 20 oC, 40% RH is mixed adiabadically with air at 40 oC, 40% RH in
the ratio of 1 kg of the former with 2 kg of the latter (on dry basis).
Determine the specific humidity and the enthalpy of the mixed stream.
PART C – (1 x 15 = 15 marks)
16. (a) A quantity of air undergoes a thermodynamic cycle consisting of three

processes. Process 1 – 2 : Constant volume heating from P1 = 0.1 MPa,
120

T1 = 15 oC, V1 =n 0.02 m3 to P2 =0.42MPa. Process 2-3 : Constant

pressure cooling. Process 3-1 : Isothermal heating to the initial state.
Employing the ideal gas model with Cp = 1 kJ/kgK, evaluate the change
of entropy for each process. Sketch the cycle on p-v and T-s
coordinates. (P51,Q13)
Or
(b) Air at 80 kpa, 27 oC and 220 m/s enters a diffuser at a rate of 2.5 kg/s
and leaves at 42 oC. The exit area of the diffuser is 400cm2. The air is
estimated to lose heat at a rate of 18 kJ/s during this process.
ww (i) the exit velocity and
w.E
(ii) the exit pressure of the air.(P23,Q12)
asy
En
gin
eer
ing
.ne
t
121

B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/ DECEMBER 2016.

Third Semester
ME 6301 - ENGINEERING THERMODYNAMICS
(Regulation 2013)
Answer ALL Questions
PART - A (10 x 2 =20 Marks)
1. Should the automobile radiator be analyzed as a closed system or as an open
system? Explain.
ww
2. What are intensive and extensive properties?(P1,Q2)
w.E
3. A heat engine with thermal efficiency of 45 percent rejects 500KJ/Kg of heat. How
much heat does it receive?
asy
4. When system is adiabatic what can be said about the entropy change of the
substance in the system?
En
5. Is iced water a pure substance ? why?(P54,Q1)
gin
eer
6. What is the effect of reheat on (a)the network output (b) the cycle efficiency and
(c)steam rate of steam power plant?
7. What are reduced properties? ing

8. Write down the Two Tds equations
.ne
9. State the Dalton’s law of partial pressures.
10. What is dew point temperature?(P92,Q1)

t
PART B (5 x 13 = 65 Marks)
11. (a) A Piston –cylinder device contains 0.15kg of air initially at 2 MPa and
3500C. The air is first expended isothermally to 500KPa, then compressed
polytropically with a polytrophic exponent of 1.2 to the initial pressure and
finally compressed at the constant pressure to the initial state .Determine the
boundary work for each process and the network of the cycle.(P20,Q10)
(OR)
122

(b) Air enters the compressor of a gas- turbine plant at ambient conditions of
100KPa and 25:C with a low velocity and exits at 1MPa and 347: C with a
velocity of 90 m/s .The compressor is cooled at a rate of 1500KJ/min and the
power input to the compressor is 250KW. Determine the mass flow rate of air
through the compressor. Assume Cp = 1.005KJ/KgK(P22,Q11)
12. (a) (i) A heat pump operates on a carnot heat pump cycle with a COP of
8.7. it keeps a space at 24:C by consuming 2.15 kw of power. Determine the
temperature of the reservoir from which the heat is absorbed and the heating
load provided by the heat pump.(P46,Q8)
ww (ii) An inventor claims to have developed a refrigeration system that removes

heat from the closed region at – 12:C and transfers it to the surrounding air at
w.E
25:C while maintaining a COP of 6.5 . is this calm reasonable? (P50,Q11)
(OR)
asy
(b) (i) A 30 kg iron block and a 40 kg copper block, both initially at 80: C.
Thermal equilibrium is established after an while as a result of heat transfer
En
between the blocks and the lake water. Determine the total entropy change
for this process.(P47,Q9)
gin
(ii) How much of the 100 kJ of thermal energy at 650 K can be converted to
eer
useful work? Assume the environment to be at 25:C.(P51,Q12)
13.
ing
(a) A steam initially contains 5 m 3 of steam and 5 m3 of water at 1MPa. Steam
is taken out at constant pressure until 4 m 3 of water is left. What is the heat
transferred during the process?(P74,Q9)
.ne
(OR)
(b) A regenerative cycle utilizes steam as a working fluid . Steam is supplied

t
to the turbine at 40 bar and 4500C and the condenser pressure is 0.03bar.
After expansion is the turbine to 3 bar, some of the stream is extracted from
the turbine for heating feed water from the condenser in an open heater. The
pressure in the boiler is 40 bar and the state of the fluid leaving the heater is
saturated liquid water at 3 bar Assuming isentropic heat drop in the turbine
and pumps, compute the efficiency of the cycle. (ii) When will you call a
vapour superheated? Give example. Also when will you call a liquid as
compressed liquid? Give example. (P43, Q 14)
123

14. (a) (i) One kg of CO2 has volume of 1 m3 at 100o C. compute the pressure by
Vander waal’s equation
Perfect gas equation
The vander waal’s constant a = 362850 Nm4/(kg-mol)2 and

b=0.0423m3/(kg-mol).
(ii) Write the berthelot and dieterici equations of state. (P90,Q8)
(OR)
ww (b) (i) What is Joule-Thomson coefficient? Why is it zero for an ideal

gas?(P87,Q7)
w.E
(ii) Derive and expression for clausius Clapeyron equation applicable to
fusion and vapourization.(P79,Q1)
15. asy
(a) A rigid tank that contains 2 kg of N2 at 25 C and 550kpa is connected to
En
another rigid tank that contains 4 kg of O2 at 25 C and 50 kpa. The valve
connecting the two tanks is opened and the two gases are allowed to mix. If
gin
the final mixture temperature is 25 C, determine the volume of each tank and
the final mixture pressure.
(OR) eer
ing
(b) An air conditioning system is designed under the following conditions:
Outdoor conditions 150C DBT and 100C WBT .ne

Required conditions 200C DBT and 50% RH
Amount of free air circulated 0.25 m3/min person

t
Seating capacity – 50 persons
The required condition is achieved first by heating and then by adiabatic

humidifing . Determine the following
1. Capacity of heating coil in kw
2. Capacity of humidifier (P111,Q8)
124

PART C (1 x 15 = 15 Marks)
16. (a) (i) A household refrigerator that has a power input of 450 W and a COP of
1.5 is to cool 5 lage watermelons, 10 kg each, to 8o C. if the watermelons are initially
at 28oC, determine how long it will take for the refrigerator to cool them. The
watermelons can be treated as water whose specific heat is 4.2 kj/kg k. is your
answer realistic or optimistic? Explain. (P116,Q13)
(ii) What are the desirable characteristics of a working fluid most

suitable for vapour power cycles?
ww
w.E (OR)
(b) (i) How do you minimize the energy consumed by your domestic
asy
refrigerator?(P114,Q9)
En
(ii) The interior lighting of refrigerators is provided by incandescent lamps
whose switches are actuated by the opening of the refrigerator door. Consider a
gin
refrigerators whose 40 W light bulb remains on continuously as a result of
performance of 1. 3 and the cost of electricity is Rs. 5 per kWh, determine the
eer
increase in the energy consumption of the refrigerator and its cost per year if the
ing
switch is not fixed. Assume the refrigerator is opened 20 times a day for an average
of 30 s.(P115,Q10)
.ne
t
125

Question Paper code: 51845

B.E / B.TECH DEGREE EXAMINATION, MAY/JUNE 2016
Third Semester
REGULATION 2008/2010
ww PART – A (10 x 2 =20 Marks)
1. Define the Zeroth Law of thermodynamics. Why is it so called?
w.E
2. List any five physical properties of matter which can be used for measurement of
temperature.
asy
3. List the limitations of first law of Thermodynamics. (P21, Q12)
En
4. In an isothermal process 1000 kJ of work is done by the system at a temperature
gin
of 200OC. What is the entropy change in this process? (P21, Q13)
5. Define a pure substance. (P 39, Q1)

eer
ing
6. How is triple point represented in a P-v diagram? (P39, Q3)
.ne
7. Why do the specific heats of an ideal gas depend only on the atomic structure of
the gas?
8. Define volumetric expansivity. (P 58, Q11)
9. When is humidification of air necessary?

t
10. How does the wet bulb temperature differ from the dry bulb temperature?
11. (a) A thermodynamic system operates under steady flow conditions, the fluid
entering at 2 bar and leaving at 10 bar. The entry velocity is 30 m/s and exit
velocity is 10 m/s. During the process 25 MJ/hr of heat from an external
source is supplied and the increase in enthalpy is 5 kJ/kg. The exit point is 20
126

m above the entry point. Determine the flow work from the system if the fluid
flow rate is 45 kg/min
(OR)
(b) A vessel of constant volume 0.3 m3 contains air at 1.5 bar and is connected
via a valve to a large main carrying air at a temperature of 38 OC and high
pressure. The valve is opened allowing air to enter the vessel and raising the
pressure therin to 7.5 bar. Assuming the vessel and valve to be thermally
insulated, find the mass of air entering the vessel.
12. (a) (i) Define the terms “ Irreversible process” and “ Reversible process”.
ww Give an example of each.
w.E
(ii) In a Carnot cycle the maximum pressure and temperature are limited to
18 bar and 410OC. The volume ratio of isentropic compression is 6 and
asy
isothermal expansion is 1.5. Assume the volume of the air at the beginning
of isothermal expansion as 0.18 m 3. Show the cycle on p-V and T-s
diagrams and determine
En
gin
(1) Pressure and temperature at main points
(2) Thermal efficiency of the cycle (P 22, QI a)
(OR) eer
(b) (i) State and prove Clausius inequality. ing
.ne
(ii) A metal block with m= 5 kg, C = 0.4 kJ/kg K at 40 OC is kept in a room at
20OC. It is cooled in the following two ways:
(1) Using a Carnot engine (executing integral number of cycles) with the
t
room itself as the cold reservoir;
(2) Naturally (P32, Q V a)
13. (a) (i) Discuss the different zones of T-V diagram for water when the
temperature rises from -20OC to 200OC at 1 atm pressure. (P 45, Q I)
(ii) A vessel of volume 0.04 m3 contains a mixture of saturated water

and saturated steam of 250OC. The mass of the liquid present is 9 kg. Find
127

the pressure, the mass, the specific volume, the enthalpy, the entropy and
the internal energy (P 46, Q II)
(OR)
(b) Steam at 90 bar and 480 OC is supplied to a steam turbine. The steam is
reheated to its original temperature by passing the steam through reheater at
12 bar. The expansion after reheating takes place to condenser pressure of
0.07 bar. Find the efficiency of the reheat cycle and work output if the flow of
steam is 5 kg/s. Neglect the pressure loss in the system and assume
expansions through the the turbine are isentropic. Do not neglect pump work.
ww
14.
w.E
(a) (i) Derive the Clausius- Clapeyron equation and discuss its significance.
(ii) Write down two Tds relations ( P 65, Q 5)
asy (OR)
En
(b) (i) Derive any two Maxwell’s relation (P 62, QII)
gin
(ii) Draw a neat schematic of compressibility chart and indicate its salient
15.
features. (P 64, Q III)
eer
(a) (i) Derive the sensible heat factor for cooling and dehumidification
process. Also explain the process.
ing
.ne
(ii) One kg of air at 40 OC dry bulb temperature and 50% relative humidity is
mixed with 2 kg of air at 20 OC dry bulb temperature and 20 OC dew point
temperature. Calculate the temperature and specific humidity of the mixture.
(OR)
t
pv
(b) (i) Prove the specific humidity of air is w  0.622
pb  pv
b(ii)with the aid of a model psychrometric chart explain the following

processes
(1) Adiabatic mixing
(2) Evaporative cooling
128

Question Paper code: 57539

B.E / B.TECH DEGREE EXAMINATION, MAY/JUNE 2016
Third Semester
REGULATION 2013
ww PART – A (10 x 2 =20 Marks)
1. Write down the equation for the first law for a steady flow process.
w.E
2. Give the energy equation applicable for an adiabatic nozzle and an adiabatic
turbine.
asy
3. A reversible heat engine operates between a source at 800 OC and a sink at 30 OC.
En
What is the least rate of heat rejection per kW network output of the engine.
(P27,Q10)
gin
4. Define Irreversibility. (P27, Q11)
eer
5. State the phase rule for pure substance. (P 55, Q4)
ing
6. Mention the working fluids used in binary vapour cycle. (P 55, Q 5)
7. What are reduced properties? Give their significance. .ne

8. What is the importance of Joule –Thomson coefficient?.
9. State Dalton’s law of partial pressure. On what assumptions this law is based.
t
10. What is adiabatic mixing and write the equation for that.
11. (a) A mass of air is initially at 260 OC and 700 kPa and occupies 0.028m3. The
air is expanded at constant pressure to 0.084 m 3. A polytropic process with n
= 1.5 is then carried out followed by a constant temperature process which
completes a cycle. All the process are reversible.
129

(1) Sketch the cycle n T-S and p-V planes

(2) Find the heat received and heat rejected in the cycle
(3) Find the efficiency of the cycle (P3, QI)
(OR)
(b) (i) A room for four persons has 2 fans each consuming 0.18 kW power and
three 100 W lamps. Ventilation air at the rate of 80 kg/hr enters with an
enthalpy of 84 kJ/kg and leaves with an enthalpy of 59 kJ/kg. If each person
puts out heat at the rate of 630 kJ/hr, determine the rate at which heat is
removed by a room cooler, so that a steady state is maintained in the room
ww (P6, QII a)
w.E
(ii) An insulated rigid tank of 1.5 m 3of air at a pressure of 6 bar and 100 OC
discharges air in to the atmosphere which is at 1 bar through a discharge pipe
asy
till its pressure becomes 1 bar.
En
(1) Calculate the velocity of air in the discharge pipe
gin
(2) Evaluate the work that can be obtained from the frictionless
turbine using the kinetic energy of that air. (P7, QII b)
12. eer
A heat engine operating between two reservoirs at 1000 K and 300 K is used
ing
to drive a heat pump which extracts heat from the reservoir at 300 K at a rate
twice that at which the engine rejects heat to it. If the efficiency of the engine
is 40% of the masimum possible and the COP of the heat pump pis 50% of the
maximum possible, what is the temperature of the reservoir to which the heat .ne
pump rejects heat? What is the rate of heat rejection from the heat pump if
the rate of heat supply to the engine is 50 kW. (P 45, Q VII b)
t
(OR)
(b) (i) 50 kg of water is at 313 K and enough ice at -5 OC is mixed with water
in an adiabatic vessel such that at the end of the process all the ice melts and
water at 0 OC is obtained. Find the mass of ice required and the entropy
change of water and ice. Given C p of water = 4.2 kJ/kg K and Cp of ice = 2.1
kJ/kg K and the latent heat of ice = 335 kJ/kg (P41, Q Vb)
130

(ii) A heat engine receives 800 kJ of heat from a reservoir at 1000 K and
rejects 400 kJ at 400 K. If the surrounding is at 300 K, calculate the first and
second law efficiency and the relative efficiency of the heat engine.
13. (a) A large insulated vessel is divided into two chambers, one containing 5 kg
of dry saturated steam at 0.2 MPa and the other 10 kg of steam, 0.8 quality
at 0.5 MPa. If the partition between the chambers is removed and the
steam is mixed thoroughly and allowed to settle, find the final pressure,
steam quality and entropy change in the process. (P 62, Q IV)
ww (OR)
(b) (i) Why is Carnot cycle not practicable for a steam powerplant?
w.E
(ii) In a steam power plant the condition of steam at inlet to the turbine is 20
bar and 300 OC and the condenser pressure is 0.1 bar. Two feed water heaters
asy
operate at optimum temperatures. Determine (1) The quality of steam at
En
turbine exhaust (2) network per kg of steam (3) cycle efficiency (4) the steam
rate. Neglect pump work. (P 65, Q V)
gin
14. eer
(a) (i) A vessel of volume 0.28 m3 contains 10 kg of air at 320 K. Determine
ing
the pressure exerted by the air using a) Perfect gas equation b) Vander Waals
equation c) Generalized compressibility chart (Take critical temperature of
air as 132.8 K and critical pressure as 37.7 bar) .
.ne
(ii) Draw the neat schematic of a compressibility chart and indicate the
salient features.
(OR)
t
(b) What is meant by phase change process? Derive Clausius – Clapeyron
equation for a phase change process. Give the significance of this equation
(P 79, Q I)
15. (a) A rigid tank of 5 m3 contains gas mixture comprising 3 kg of O2 and 4 kg of
N2 and 5 kg of CO2 at 290 K. Calculate the molar specific volume, initial
pressure of the gas. If it is heated to 350 K, calculate the heat transfer and
change in enthalpy. Also verify the Gibbs theorem for entropy
(OR)
131

(b) A room 7m x 4m x 4m is occupied by an air – water vapour mixture at

38OC. The atmospheric pressure is 1 bar and the relative humidity is 70%.
Determine the humidity ratio, dew point, mass of dry air and mass of water
vapour. If the mixture of air – water vapour is further cooled at constant
pressure until the temperature is 10OC. Find the amount of water vapour
condensed.
ww
w.E
asy
En
gin
eer
ing
.ne
t
132

B.E/B.Tech. DEGREE EXAMINATION, NOV/DEC 2015
Third Semester
(Regulation 2013)
Time: Three hours Maximum: 100 marks
ww PART-A (10x2=20 marks)
w.E
1. State the thermodynamics definition of work. ((P3, Q11)
2. Classify the following properties as intensive or extensive or neither. (a) Pressure
asy
(b) Temperature (c) Volume (d) Internal energy (e) volume per mole (f)) Enthalpy
per unit mass. (P3, Q12)
En
3. What is triple point? For a pure substance, how many degrees of freedom are
there at triple point?
gin
4. A vessel of 2 m3 contains a wet steam of quality 0.8 at 210°C. Determine the mass
eer
of the liquid and vapour present in the vessel. (P 55, Q 6)
5. Define degree of saturation.
6. State Gibbs-Dalton’s law. (P 78, Q9)
ing
7. Express Clausius inequality for various processes. . (P25, Q3)
8. Define second law efficiency. . (P25, Q4)
.ne
9. What is known as equation of state?
10. Write the Clausius-Clapeyron equation and label all the variables.
t
PART- B (5x16=80)
11 (a) A piston-cylinder assembly contains air (ideal gas with γ =1.4) at 200kPa and
occupies a volume of 0.01m3. The piston is attached to one end of a spring and
the other end of the spring is fixed to a wall. The force exerted by the spring on
the piston is proportional to the decrease in the length of the spring from its
natural length. The ambient atmospheric pressure is 100 kPa. Now, the air in
the cylinder is heated till the volume is doubled and at this instant it is found
133

that the pressure of the air in the cylinder is 500 kPa. Calculate the wok done by
the gas.
Or
(b) An insulated rigid tank having 5kg of air at 3 atm and 30°C is connected to an air
supply line at 8 atm and 50°C through a valve. The valve is now slowly opened
to allow the air from the supply line to flow into the tank unit the tank pressure
reaches 8 atm, and then the valve is closed. Determine the final temperature of
the air in the tank. Also find the amount of air added to the tank.
ww
12. (a) One kmol of methane is stored in a rigid vessel of volume 0.6m3 at 20°C.
Determine the pressure developed by the gas by making use of the
w.E
compressibility chart. (P 86, Q VI)
Or
(b) Derive the entropy equations. (P 85, Q V) (16)
asy
13. (a) State the Carnot principles and prove the first principle with relevant
sketches.
En (16)
Or
gin
(b) One kilogram of water at 273 K is brought into contact with a heat reservoir
at 373 k.
eer
(i) When the water has reached 373 k, find the change in entropy of the water, of
ing
the heat reservoir, and of the universe. (ii) If the water had been heated from273
.ne
K to 373 K by first bring it in contact with a reservoir at 323 K and then with a
reservoir at 373K, what would have been the change in entropy of the universe?
14. (a) Draw the p-V, T-S, h-S diagrams and theoretical lay out for Rankine cycle
t
and hence deduce the expression for its efficiency. (16)
Or
(b) (i) State the advantages of using super heated steam in vapour power cycle.
(6)
(ii) A vessel with a capacity of 0.05 m3 contains a mixture of saturated water

and saturated steam at a temperature of 245°C. The mass of the liquid
present is 10 kg. Find the following:
134

(1) The pressure

(2) The mass
(3) The specific volume
(4) The specific enthalpy
(5) The specific entropy and
(6) The specific internal energy. (10)
15. (a) In an engine cylinder a gas has a volumetric analysis of 13% CO 2, 12.5 % O2
and 74.5% N2. The temperature at the beginning of expansion is 950°C and the
gas mixture expands reversibly through a volume ration of 8:1, according to the
wwlaw pv1.2 = constant. Calculate per kg of gas:

(i) The work done:
w.E
(ii) The heat flow:
(iii) Change of entropy per kg of mixture.
The values of c p for the constituents CO2, O2 and N2 are 1.235 kJ/kg K, 1.088
asy
kJ/kg K and 1.172 kJ/kg K respectively.
Or
En
(b) (i) The sling psychrometer in a laboratory test recorded the following
readings:
Dry bulb temperature = 35°C gin
Wet bulb temperature = 25°C
Calculate the following : eer
(1) Specific humidify
ing
(2) Relative humidity
(3) Vapour density in air .ne
(4) Dew point temperature
(5) Enthalpy of mixture per kg of dry air take atmostpheric pressure = 1.0132
bar. ( P 94, Q I)
t
(ii) Write a short note on mixing of air steams in psychrometry. (8)
135

B.E/B.Tech. DEGREE EXAMINATION, NOV/DEC 2015
Third Semester
ME2202– ENGINEERING THERMODYNAMICS
(Regulation 2008/2010)
Time: Three hours maximum: 100 marks
ww PART-A (10x2=20 marks)
w.E
1. Show how zeroth law of thermodynamics is used for temperature measurement.
2. Show that the energy of an isolated system remains constant.
asy
3. What are the causes of irreversibility?
4. What is entropy principle?

En
5. What is normal boiling point? ( p 56, Q7)
gin
eer
6. When is reheat recommended in a steam power plant? (P 56, Q8)
ing
7. Why do the specific heats of an ideal gas depend only on the atomic structure of
the gas?
8. Define volume expansivity. .ne

9. Define dew point temperature. (P 92, Q 1)
10. What is chemical dehumidification? (P 92, Q 2)

t
PART B (5x16=80 marks)
11. (a) (i) A mass of gas is compressed in a quasi-static process from 80 kPa, 0.1 m 3
to 0.04 MPa, 0.03 m3. Assuming that the pressure and volume are related by
pv1.35 = constant, fine the work done by the gas system. (5)
(ii) A milk chilling unit can remove heat from the milk at the rate of 41.87
MJ/h. Heat leaks into the milk from the surrounding at an average rate of
136

4.187 MJ/h. Find the time required for cooling a batch of 500kg of milk from
45°C to 5°C. Take cp of milk to be 4.187 KJ/kgK. (11)
Or
(b) (i) Write the steady flow energy equation for a boiler. (6)
(ii) Air flows steadily at the rate of 0.04kg/s through an air compressor,
entering at 6 m/s with a pressure of bar and a specific volume of 0.85m 3/kg
and leaving at 4.5 m/s with a pressure of 6.9 bar and a specific volume of 0.16
m3 /kg. The internal energy of the air leaving is 88 kJ/kg greater than that of
entering air. Cooling water surrounding the cylinder absorbs heat from the
ww air at the rate of 59W. Calculate the power required to drive the compressor
and the inlet and outlet cross sectional areas. (10) (P13, QVI)
w.E
12. (a) (i) What is a reversed Carnot heat engine? (5)
asy
(ii) A heat pump working on a reversed carnot cycle taken in energy from
reservoir maintained at 3°C and delivers it to another reservoir where
En
temperature is 77°C. the heat pump drivers power for its operation from a
gin
reversible heat engine operating with in the higher and lower temperature
limits of 1077°C and 77°C. For 100 kJ/s of energy supplied to the reservoir at
eer
77°C, estimate the energy taken from the reservoir at 1077°C. (11) (P36, QIII)
Or
ing
(b) (i) What is available energy and unavailable energy with reference to a
thermodynamic cycle? (4) .ne
(ii) A fluid undergoes a reversible adiabatic compression from 0.5 MPa, 0.2 m 3
to 0.05 m3, according to the law pv1.3 = constant. Determine the change in
t
enthalpy, internal energy and entropy and the heat transfer and work
transfer during the process. (12)
13. (a) (i) Discuss the different zones of T-V diagram for water when the
temperature rises from -20°C to 200°C at 1 atm pressure (8)
(ii) A Vessel of volume 0.04m3 contains a mixture of saturated water and

saturated steam at a temperature of 250°C. The mass of the liquid present is 6
kg. Find the pressure, the mass, the specific volume, the enthalpy, the entropy
and the internal energy. (8)
137

Or
(b) Steam at 90 bar and 480° C is supplied to a steam turbine. The steam is
reheated to its original temperature by passing the steam through reheater at
12 bar. The expansion after reheating taken place to condenser pressure of
0.07 bar. Find the efficiency of the reheat cycle and work output if the flow of
steam is 5 kg/sec. Neglect the pressure loss in the system and assume
expansions through the turbine are isentropic. Do not neglect pump work.
14. (a) A mass of 0.25 kg of an ideal gas has a pressure of 300 kpa, a temperature of
80°C and a volume of 0.07 m 3 . the gas undergoes an irreversible adiabatic
ww process to a final pressure of 300kPa and final volume of 0.10m 3 , during

which work done on the gas is 25kJ. Evaluate c p and cv of the gas the increase
w.E
in entropy of the gas.
Or
(b) The gas neon has a molecular weight of 20.183 and its critical
(16)
asy
temperature, pressure and volume are 44.5 k, 2.73 Mpa and 0.0416 m 3/kg
En
mol. Reading from a compressibility factor z is 0.7. What are the
corresponding specific volume, Pressure, temperature and reduced volume?
gin (16)
15. (a) (i) The sling psychometer reads 40°C DBT and 28°C WBT. Calculate, specific
eer
humidity, relative humidity, vapour density in air, dew point temperature and
enthalpy of mixture per kg of dry air. Assume atmospheric pressure to be
1.03 bar.
ing
(ii) What is wet bulb depression and where is it equal to zero?
.ne (4)
(b) (i) Explain adiabatic evaporative cooling.
Or
(6)
t
(ii) Air at 20°C, 40% relative humidity is mixed adiabatically with air at 40°C,
40% relative humidity in the ratio of 1 kg of the former with 2 kg of the latter
(on dry basis). Find the condition of air. (10)
138

B.E. / B.Tech. DEGREE EXAMINATION, APRIL/MAY 2015
ME6301 – ENGINEERING THERMODYNAMICS
(Regulation 2013)
PART A – (10 X 2 = 20 Marks)
1. State the first law for a closed system undergoing a process and a cycle. (P2,
Q7)
ww2. Why does free expansion have zero work transfer? (P2, Q8)
w.E
3. What is a thermal energy reservoir? Explain the term ‘source’ and ‘sink’. (P25,
Q1)
asy
4. What is a reversed heat engine? . (P25, Q2)
En
5. What is meant by dryness fraction of steam? (P 57, Q9)
gin
6. Draw the standard Rankine cycle on P-V and T-S coordinates. (P57, Q 10)
7. What is joule-Thomson coefficient? Why is it zero for an ideal gas? (P 77, Q7)
eer
8. What is the law of corresponding states? (P 78, Q8)
9. What is Amagat’s law? ing

10. What is sensible heating? .ne
PART B – (5 x 16 = 80 Marks)
11. (a) A gas undergoes a thermodynamic cycle consisting of the following process:
t
i. Process 1-2: Constant pressure P1 = 1.4 bar, V1 = 0.028 m3, W12=10.5 KJ.
ii. Process 2-3: Compression with PV=constant, U3=U2.
iii. Process 3-1: Constant volume, U1-U3=-25.4 Kj
There are no significant changes in KE and PE.
1) Sketch the cycle on P-V diagram
139

2) Calculate the network for the cycle in KJ
3) Calculate the heat transfer for process 1-2
4) Show that (P15, QVII)
11. (b) A turbine operating under steady flow conditions receive steam at the
following state: Pressure 13.8 bar; specific volume 0.143 m3/Kg ; internal energy
2590 KJ/Kg; Velocity 30 m/s. The state of the stream leaving the turbine is: Pressure
0.35 bar; Specific Volume 4.37 m3/Kg; Internal energy 2360 KJ/Kg; Velocity 90 m/s.
Heat is lost to the surrounding at the rate of 0.25 KJ/s. If the rate of steam flow is
ww
0.38 Kg/s , What is the power developed by the turbine?
12. (a) A reversible heat engine operates between two reservoirs at temperature of
w.E
6000C and 400 C. The engine drives a reversible refrigerator which operates
between reservoirs at temperature of 40 0 C to -200 C. The heat transfer to the hear
asy
engine is 2000 KJ and the network output for the combined engine refrigerator is
360 KJ. Calculate the heat transfer to the refrigerator and net heat transfer to the
reservoir at 400 C.
En
gin
12. (b) Two kg of air at 500 Kpa , 800C expands adiabatically in a closed system until
its volume is doubles and its temperature become equal to that of the surrounding
eer
which is at 100 Kpa. 50 C. For this process determine: (i) the maximum work (ii) the
change in availability (iii) the irreversibility (P 43, Q VI a)
ing
13. (a) A vessel of volume 0.04 m3 contains a mixture of saturated water and
saturated steam at a temperature of 250 0C. the mass of the liquid present is 9 Kg.
.ne
Find the pressure, the mass, the specific volume, the enthalpy and entropy and
internal energy of the mixture.
13. (b) A steam power plant operates on a simple rankine cycle between the
t
pressure limits of 3 MPa and 50 Kpa. The temperature of the steam at the turbine
inlet is 3000C and the mass flow rate of steam through the cycle is 35Kg/s. Show the
cycle on a T-S diagram with respect to saturation lines, and determine (i) the
thermal efficiency of the cycle (ii) the net power output of the power plant.
14. (a) Derive any three of the Maxwell relation.
14. (b) Determine the pressure of nitrogen gas at T=175 K and v = 0.00375 m3/Kg
on the basis of (i) the ideal-gas equation of state (ii) the Vander Walls equation of
140

state. The Vander walls constants for nitrogen are a=0.175m6kpa/Kg2,

b=0.00138m3/Kg. (P 84, Q IV)
15. (a) A gas mixture consists of 7 Kg nitrogen and 2 Kg oxygen, at 4 bar and 27 0 C.
Calculate the mole fraction, partial pressure, molar mass, gas constant, volume and
density.
15. (B) Atmospheric air at 1.0132 bar has a DBT of 300 C and WBT of 250 C. Compute
(i) the partial pressure of water vapour (ii) specific humidity (iii) the dew point
temperature (iv) the relative humidity (v) the degree of saturation (vi) the density
of air in the mixture (vii) the density of vapour in the mixture (viii) the enthalpy of
ww
the mixture. Use the thermodynamics tables only.
w.E
asy
En
gin
eer
ing
.ne
t
141

B.E. / B.Tech. DEGREE EXAMINATION, APRIL/MAY 2015
ME2202 – ENGINEERING THERMODYNAMICS
(Regulation 2008)
Answer all question
PART A – (10 X 2 = 20 Marks)
1. Define the Zeroth law of thermodynamics. Why is it so called? (P2, Q9)
ww2. Last any five physical properties of matter which can be used for
w.E
measurement of temperature. (P3, Q10)
3. A closed insulated vessel contains 200 Kg of water. A paddle wheel immersed
asy
in the water is driven at 400 rev/min with an average torque of 500 Nm. If
the test run is made for 30 minute, determine rise in the temperature of
En
water . Take specific heat of water 4.18 KJ/Kg K. (P28,Q14)
gin
4. A heat engine is supplied with 2512 KJ/min of heat at 650 0C, heat rejection
take place at 100 0 C. Specify which of the following heat rejection represents
eer
a reversible, irreversible or impossible result (a) 867 KJ/min (ii) 1015
KJ/min. (P28, Q15)
ing
5. Superheated steam at 30 bar and 3000C enter a turbine is expanded to 5 bar
and quality 0.974 dryness, compute the loss is availability for the adiabatic
.ne
process if the atmospheric temperature is 2700 C.
6. Define second law of thermodynamics. t

7. A domestic food freezer maintains a temperature of -150 C. The ambient air
temperatue is 30°C. if the heat leaks into freezer 1.75 KJ/s continuously.
What is the least power necessary to pump this heat continuously?
8. One kg on an ideal gas is heated from 18°C to 93°C. Taking R=269 Nm/Kg K
and γ=1.2 for gas. Find the change in internal energy.
9. Carnot refrigerator require 1.25 KW per ton of refrigeration to maintain the

temperature of 243 K. Find the COP of Carnot refrigerator.
142

10. Ice is formed 0°C from water at 20°C. the temperature of the brine is -10°C.
Find the ics formed per KW hour. Assume that refrigeration cycle used is
perfect reversed Carnot cycle. Latent heat of ice = 80 Kcal/Kg.
PART B – (5 x 16 = 80 Marks)
11. (a) A thermodynamics system operates under steady state flow condition, the
fluid entering at 2 barand leaving at 10 bar. The entry velocity is 30 m/s and
exit velocity is 10 m/s. During the process 25MJ/hr of heat from an external
source is supplied and the increase in enthalpy is 5KJ/Kg. The exit point is
20m above the entry point. Determine flow work from the system if the fluid
ww flow rate is 45 Kg/min.
11. (b)A vessel of constant volume 0.3 m3 contain air at 1.5 bar and it connected
w.E
via a value , to a large main carrying air at a temperature of 33°C and high
pressure. The value is opened allowing air to enter the vessel and raising the
asy
pressure therein to 7.5 bar. Assuming the vessel and valve to be thermally
insulated . Find the mass of air entering the vessel.
En
12. (a) Three Carnot engines A,B and C working between the temperature of
gin
1000 K and 300 K are in a series combination. The work produces by these
engines are in the ratio 0f 5:4:3 Make calculation of temperature for
intermediate reservoirs.
eer
ing
12. (b)A reversible engine operates between temperatures T1 and T (T1 > T).The
energy rejected from this engine is received by a second reversible engine at
the same temperature T. The second engine rejects energy at temperature T2
.ne
(T2 < T). Prove that T=(T1+T2)/2 if the engine produce same work output
13. (a) A power generation point uses steam as a working fluid and operates at a
boiler pressure of 50 bar, dry saturated and a condenser pressure of 0.05 bar.
t
Determine the cycle efficiency, work ratio and specific steam consumption for
Rankine cycle.
13. (b) A steam power plant operates on a theoretical reheat cycle. Steam at 25
bar pressure and 400°C is supplied to the high pressure turbine. After its
expansion to dry state the steam is reheated at a constant pressure to its
original temperature. Subsequent expansion occurs in the low pressure
turbine to a condenser pressure of 0.01 bar. Considering feed pump work,
143

Make calculation to determine (i) Quality of steam at entry to condenser (ii)

Thermal efficiency (iii) specific steam consumption.
14. (a) A tank of 0.2 m3 capacity contains O2 at 15 bar and 400°C. A second tank
of 0.5 m3 contains N2 at 20 bar and 300°C. the two tanks are connected
together and allow to mix. The heat lost during mixing is 50 KJ. Determine
the final pressure, final temperature of the mixture and net entropy change
due to mixing.
14. (b) Five moles of gas mixture contains 45%N 2 , 27% He and 28% C6H6 by
mass. Find (i) the analysis by volume and number of moles of each
ww constituent (ii) the volume of mixture at 3.5 bar pressure and 20°C.
15. (a) A certain sample of moist air exit at 35°C DBT and 20°C dew point
w.E
temperature the atmospheric pressure is 760 mm of mercury. Calculate the
relative humidity and saturation ratio.
asy
15. (b) (i) explain the process of cooling dehumidification of air (8)
En
(ii) Draw the psychometric chart and show any two psychometric process.(4)
gin
(iii) What is moist air and saturated air. (4)
eer
ing
.ne
t
144

B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2014.
Third Semester - Mechanical Engineering
(Regulation 2013)
PART - A (10x2=20marks)
1. Define thermodynamic equilibrium
ww2. Enlist the similarities between work and heat. (P1, Q5)
w.E
3. An inventor claims to have developed an engine which absorbs 100KW of
heat from a reservoir at 1000k produces 60KW of work and rejects heat to a
asy
reservoir at 500K. Will you advise investment in its development? (P19, Q 8)
En
4. A turbine gets a supply of 5 kg/s of steam at 7 bar,2500C and discharges it at
1 bar. Calculate the availability. (P27, Q9)
gin
5. Draw the p-T diagram for water and, label all salient points. (P 58, Q 12)
eer
6. State the advantages of using super heated steam in turbines. (P 58, Q11)
ing
7. What is known as equation of state and when it can be used for engineering
calculations? (P 77, Q 5)
8. What are known as thermodynamic gradients? (P 77, Q6) .ne

9. Define molar mass. t
10.Define sensible heat factor.
PART B - (5 x 16 = 80 marks)
11.(a) Three grams of nitrogen gas at 6 atm and 160 oC in a frictionless

piston cylinder device is expanded adiabatically to double its initial volume,
then compressed at constant pressure to its Initial volume and then
compressed again at constant volume to its initial state. Calculate the net
work done on the gas. Draw the P-V diagram for the processes.(P9, QIV)
145

Or
(b) 90 k-J of heat is supplied to a system at a constant volume. The system rejects
95 kJ of heat at. Constant pressure and 18 kJ of work is done on it. The system is
brought to original state by adiabatic process. Determine
(i) The adiabatic work
(ii) The values of internal energy at all states if initial value is 105KJ
(P11, QV)
12. (a) Two heat engines operating in series are equal amount of work.
ww
The total work is 50 kJ/cycle. If the reservoirs are at 1000K and 250K, find the
intermediate temperature and the efficiency of each engine. Also find the heat
extracted from
w.E Or
(16)
(b) asy
5 kg of air at 550 K and 4 bar is enclosed in a closed vessel.
En
(i) Determine the availability of the system if the surrounding pressure and
temperature are 1bar and 290 K
gin (8)
eer
(ii) If the air is cooled at constant pressure to the atmospheric temperature
determine the availability and effectiveness. (P 44, Q VII a)
ing
13. (a) (i) State the conditions under which the equation of state will hold good
for a gas.
.ne
(ii) State the main reasons for the deviation of behavior of real gases from ideal
gas.
(iii) Explain irreversibility with respect to flow and non flow processes.
(4)
(4)
t
(iv) Explain the effectiveness of a system. (4)
Or
(b) Derive Maxwell relations. (16)
14. (a) Explain steam formation with relevant sketch and label all salient points
and explain every point in detail. (16)
146

Or
(b) In a Rankine cycle, the steam at inlet to turbine is saturated at a

pressure of 35 bar and the exhaust pressure is 0.2 bar. Determine
(i) The pump work
(ii) The turbine work
(iii) The Rankine efficiency
(iv) The condenser heat flow
ww (v) The dryness at the end of expansion. Assume flow rate

l
w.E
15. (a) A mixture of hydrogen (H2) and Oxygen (O2) is to be made so that
the ratio of H2 to O2 is 2: 1 by volume. If the pressure and temperature are 1 bar
and 25°C respectively, Calculate
(i) asy
The mass of 02 required (8)
(ii) En
The volume of the container. (8)
Or gin
eer
(b) 120 m3 of air per minute at 35oC DBT and' 50% relative humidity is cooled
to
ing
20°C DBT by passing through a cooling coil. Determine the following
(i) Relative humidity of Out coming air and its wet bulb temperature (6)
(ii) Capacity of cooling coil in tones of refrigeration .ne (5)
(iii) Amount of water vapour removed per hour (5) t
147

B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2014.
Third Semester
1. What is zeroth law of thermodynamics? (P1, Q3)
ww
2. Compare heat transfer with work transfer. (P2, Q6)
w.E
3. State Kelvin Planck’s statement
4. What is the entropy principle?
asy
5. What is flow and non-flow process?
6. Write the methods for improving the performance of the Rankine cycle.
En
7. What are the properties of ideal gas? ( P79, Q 12)
gin
8. State the Vander Waal’s equation of state. (P 79, Q13)
9. What is adiabatic evaporative cooling?
10. What is the use of sling psychrometer? eer
ing
Part –B (5 x16 = 80 marks)
.ne
11. (a) (i) Derive an expression for the work transfer, heat transfer and change
in internal energy for an isobaric and isochoric process
(ii) Define enthalpy. How is it related to internal energy?
(8)
(8) t
Or
(b) Air at a temperature of 15o c Passes through a heat exchanger at a velocity
of 30 m/s where its temperature is raised to 800 o C. It then enters a turbine
with the same velocity of 30 m/s and expands until the temperature falls to
650oC. On leaving the turbine, the air is taken at a velocity of 60 m/s to a
nozzle where its expands until the temperature has fallen to 500 oC. If the air
flow rate is 2kg/s, calculate (i) the rate of heat transfer to the air in the heat
148

exchanger, (ii) the power output from the turbine assuming no heat loss, and
(iii) the velocity at exit from nozzle, assuming no heat loss. Take the entropy
of air as h=cpt, where cp is the specific heat equal to 1.005 KJ/kg K and t the
temperature.
12. (a) (i) State and prove Clausius inequality. (4)

(ii) A reversible heat engine operates between two reservoirs at temperature
of 600oC and 40oC. The engine drives a reversible refrigerator which operates
ww between reservoirs at temperature of 40oC and -20oC. The heat transfer to the
heat engine is 2000 kJ and the network output of the combined engine
w.E
refrigerator plant is 360 kJ. (1) Evaluate the heat transfer to the refrigerant
asy
and the net heat transfer to the reservoir at 40 oC. (2) Reconsider (1) given
that the efficiency of the heat engine and the COP of the refrigerator are each
En
40% of their maximum possible values. (P 37, Q4)
OR
gin
eer
(b) (i) Briefly discuss about the concept of entropy.
(ii) Liquid water of mass 10 kg and temperature 20 oC is mixed with 2 kg of ice
(6)
ing
at -5oC till equilibrium is reached at 1 atm pressure. Find the entropy change of
.ne
the system. Given: Cp of ice=2.09KJ/kg Kand latent heat of ice= 334 kJ/kg. (10)
13. (a) A vessel of volume 0.04m 3 contains a mixture of saturated water and
saturated steam at a temperature of 250oC. The mass of the liquid present is 9
t
kg. Find the pressure, the mass, the specific volume, the enchalpy, the entropy
and internal energy.
(Or)
(b) Steam at 20 bar, 360oC is expanded in a steam turbine to 0.08 bar. It
then enters a condenser, where it is condensed to saturated liquid water. The
pump feeds back the water Into the boiler. (i) Assuming ideal process, find
149

per kg of steam the network and the cycle efficiency. (ii) If the turbine and
the pump have each 80% efficiency, find the percentage reduction in the
network and cycle efficiency.
14. (a) A mixture of ideal gases consists of 3 kg of nitrogen and 5 kg of CO2 at a

pressure of 3 bar and a temperature of 20oC. Find (i) mode fraction of each
constituent, (ii) the equivalent molecular weight of the mixture, (iii)the
equivalent gas constant of the mixture, (iv) the partial pressures and the
ww partial volumes, (v) the volume and density of the mixture, and (vi) the Cp and
Cv of the mixture. Take y for CO 2 and N2 to be 1.286 and 1.4 respectively.
w.E
(P 86, Q VII)
asy
(b) (i) Derive any two Maxwell’s relation.
Or
En
(ii) Deduce the expression for Joule-Thomson coefficient and draw the
inversion curve. (P 87, Q VII)
gin
eer
15. (a) Air at 20oC, 40% RH is mixed adiabatically with air at 40 oC, 40% RH in the
ing
ration of 1 kg of the former with 2kg of the latter (on dry basis). Find the final
condition of air.
.ne
Or
(b) (i) Explain adiabatic saturation with a schematic diagram.
(ii) A sling psychrometer reads 35 o C DBT and 30oC WBT. Find the
(8) t
humidity ration, relative humidity, dew point temperature, specific volume,
and enthalpy of air. (8)
150

B.E./B.Tech. DEGREE EXAMINATION, MAY/JUNE 2014.

Third Semester
1. Define Thermodynamic Equilibrium(P1, Q3)
ww
2. Differentiate between point function and path function(P1, Q4)
w.E
3. State Kelvin plank statement (P 26, Q 6)
4. Write Carnot theorem and its corollaries (P26, Q7)
asy
5. Draw a P-T (pressure temperature) diagram for a pure substance (P 58, Q 12)
En
6. Mention the possible ways to increase thermal efficiency of Rankine cycle (P 58, Q
13)
gin
eer
7. What are the assumptions made to drive ideal gas equation analytically using the
kinetic theory of gases? (P 76, Q 4)
ing
8. Using clausius- claperyon’s equation, estimate the enthalpy of vaporization at
200oC, Vg = 0.1274 m3/kg , Vf = 0.001157 m3/kg, dp/dt = 32Kpa/K (P 56, Q 3)
.ne
9. Define adiabatic saturation temperature (P 72, Q 3)
10. What is by-pass factor? (P 72, Q 4)

t
11. (a) Determine the heat transfer and its direction for a system in which a
perfect gas having a molecular weight of 16 is compressed from 101.3kpa,
20oC to a pressure of 600kpa following the law pV 1.3 = constant. Take
specific heat at constant pressure of gas as 1.7KJ/Kg K. (P8, Q III)
(OR)
151

(b) In a gas turbine installation air is heated inside heat exchanger up to

750oC from ambient temperature of 27oC. Hot air enters in to gas turbine
with the velocity of 50m/s. and leaves at 600 oC. Air leaving turbine enters
nozzle at 60m/s velocity and leaves nozzle at temperature 500 oC. For unit
mass flow rate of air, determine the following assumptions adiabatic
expansion in turbine and nozzle.
i. Heat transfer to air in heat exchanger

ii. Power output from turbine
iii. Velocity at exit of nozzle. Take Cp for air as 1.005KJ/kgoK
ww
12. (a) (i) A reversible heat pump is used to maintain a temperature of OoC in a
w.E
refrigerator when it rejects the heat to the surrounding at 25 oC. If the heat
removal rate from the refrigerator is 1440KJ/min. determine the C.O.P of the
asy
machine and work input required.
En
(ii) If the required input to run the pump is developed by a reversible
engine which receives heat at 380oC and rejects heat to atmosphere, then
determine the overall C.O.P of the system.
gin
(OR)
eer
ing
(b) 5 m3 of air at 2 bar, 27oC is compressed up to 6 bar pressure following
pV1.3 = constant. It is subsequently expanded adiabatically to 2 bar.
Considering the two processes to be reversible, determine the network, net
.ne
heat transfer, and change in entropy. Also plat the processes on T-S and P-V
diagram. (P 32. Q Ib) t
13. (a) A vessel having a capacity of 0.05m3 contains a mixture of saturated
water and saturated steam at a temperature of 245 oC. The mass of the
liquid pressure is 10kg. Find the following
a. The pressure
b. The mass
c. The specific volume
d. The specific enthalpy
e. The specific entropy and
152

f. The specific internal energy
(OR)
(b) A Steam power plant operates on a theoretical reheat cycle. Steam at

boiler at 150 bar, 550oC expands through the high pressure of 40bar to550 oC
and expands through the low pressure turbine to a condenser at 0.1bar. Draw
T-S and h-s diagram. Find:
i. Quality of steam at turbine exhaust

ii. Cycle efficiency
ww
14.
iii. Steam rate in kg/Kwh (P 67, Q VI)
(a) Drive the Maxwell relations and explain their importance in
w.E
thermodynamics.
(OR)
asy
(b) The pressure and temperature of mixture of 4 kg of O2 and 6kg of N2 are 4
En
bar and 27oC respectively. For the mixture determine the following:
The mole fraction of each component gin

The average molecular weight
eer
The specific gas constant
ing
The volume and density
.ne
The partial pressure and partial volume.
t
15. (a) An air water mixture vapour mixture enters an air conditioning unit at a
pressure of 1.0bar, 38oC, DBT, and a relative humidity of 75%. The mass of
dry air entering is 1kg/s. The air vapour mixture leaves the air conditioning
unit at 1.0 bar, 18oC, 85% relative humidity. The moisture condensed leaves
at 18oC. Determine the heat transfer rate for the process. (P 96, Q II)
(OR)
153

(b) It is required to design an air conditioning system for an industrial

process for the following hot and wet summer conditions.
Outdoor conditions 32oC DBT and 65%RH
Required air inlet conditions 25oC DBT and 60%RH
Amount of free air circulated 250m3/min
Coil due temperature 13oC
The required condition is achieved by first cooling and dehumidifying and

ww
then by heating. Calculate the following (Solve this problem with the use of
psychometric chart)
w.E
The cooling capacity of the cooling coil and its by-pass factor.
asy
Heating capacity of the heating coil in kW and surface temperature of the
heating coil if by-pass factor is 0.3.
En
The mass of water vapour removed per hour. (P 98, Q III)
gin
eer
ing
.ne
t
154

B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/ DECEMBER 2013.

Third Semester
PART – A (10 x 2 =20 Marks)
ww
1. What is microscopic approach in thermodynamics? (P1, Q1)
w.E
2. Define extensive property. (P1, Q2)
3. State Clausius Statement of Second law of thermodynamics
asy
4. Draw the schematic of an heat pump.
5. Define a pure substance

En
gin
6. How the triple point respected in the p-V diagrams
7. Define Avogadro’s law (P76, Q1)

eer
8. What is a real gas? Give example. (P 76, Q 2)
ing
9. Why do wet clothes dry in the sun faster? (P 92, Q 5)
.ne
10. Define degree of saturation. (P 93, Q6)
PART B (5 x 16 = 80 Marks) t
11. (a) Drive the steady flow energy equation and reduce it for a turbine, pump,
nozzle, and heat exchanger.
(OR)
(b) Briefly explain the following:
i. Point and path function

ii. Property, state, process, path
155

iii. Quasi static process
12. (a) (i) Two Carnot engines A and B are operated in series. The first one
receives heat at 870 K and reject to a reservoir at T. B receives heat rejected
by the first engine and in turn rejects to a sink at 300 K. Find the temperature
T for
1. Equal work outputs of both engine

2. Same efficiencies (P34, Q II)
ww (ii) Mention the clausius inequality for open, closed and isolated systems .
w.E (OR)
(b) (i) 3 kg of air at 500 kpa 90°C expands adiabatically in a closed system
asy
until its volume is doubled and its temperature become equal to that the
En
surrounding at 100 kpa and 10°C. Find maximum work, change in availability
and the irreversibility.
gin
(ii) Briefly discuss about the concept of entropy
13. eer
(a) Steam at 480°C, 90 bar is supplied to a Rankine cycle. It is reheated to 12
ing
bar and 480°C. The minimum pressure is 0.07 bar. Find the work output and
cycle efficiency using steam tables with and without considering pump work.
(OR) .ne
(b) (i) Steam initially at 0.3Mpa, 250°C is cooled at constant volume. At what
temperature will the steam become saturated vapour? What is the steam
t
quality at 80°C. Also find what is the heat transferred per kg of steam in
cooling from 250oC to 80°C. (P 69, Q VII)
(ii) When will you call a vapour superheated? Give example. Also when will
you call a liquid as compressed liquid? Give example. (P58, Q 14)
14. (a) (i) Drive the Clausius Claperyon’s equations and discuss its significance
(ii) Write down two Tds relations
156

(OR)
(b) (i) Write down two Maxwell’s relations.
(ii) Draw the neat schematic of a compressibility chart and indicate its salient
features
15. (a) (i) Air at 20oC 40% R.H is mixed with air at40oC,40% R.H in the ratio of
(former) 1:2 (later) on dry basis. Determine the final condition of air.
(ii) Briefly discuss about evaporative cooling process.
(OR)
ww (b) (i) Define the terms Relative humidity and Specific humidity.
w.E
(ii) Explain the adiabatic saturation process with a schematic.
asy
(iii) Represent heating and humidification, cooling and dehumidification
En
processes on a psychometric chart.
gin
eer
ing
.ne
t
157

ww
w.E
asy
En
gin
eer
ing
.ne
t
**Note: Other Websites/Blogs Owners Please do not Copy (or) Republish

this Materials without Legal Permission of the Publishers.
**Disclimers : EasyEngineering not the original publisher of this Book/Material

on net. This e-book/Material has been collected from other sources of net.

ME6301

Uploaded by

Copyright:

Available Formats

ME6301

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ME6301

Uploaded by

Copyright:

Available Formats

Downloaded From : www.EasyEngineering.

**Note: Other Websites/Blogs Owners Please do not Copy (or) Republish

**Disclimers : EasyEngineering not the original publisher of this Book/Material

ME6301 ENGINEERING THERMODYNAMICS LTPC

o To familiarize the students to understand the fundamentals of thermodynamics

Downloaded From : www.EasyEngineering.net

UNIT III PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE 9

UNIT IV IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS 9

Gibbs function. Psychrometric ing

Downloaded From : www.EasyEngineering.net

Detailed Lesson Plan ------------------------------------------------------------VII

Part B w.E -----------------------------------------------------------30

Unit- IV Ideal and Real Gases, Thermodynamic Relations ing

Previous Year Question Papers ----------------------------------------------------------- 119

Downloaded From : www.EasyEngineering.net

ME6301 ENGINEERING THERMODYNAMICS

Objectives of the Subject

Need and Importance for Study of the subject

Downloaded From : www.EasyEngineering.net

application in IC engines, Aircraft engines, compressors, nozzles, refrigerators and

Industry Connectivity and Latest Developments

Industrial Visit (Planned if any)

Downloaded From : www.EasyEngineering.net

ME6301- ENGINEERING THERMODYNAMICS

BASIC CONCEPTS AND FIRST LAW

Basic concepts - concept of continuum, comparison of 2 T1,

First law of thermodynamics –application to closed 2 .neT1,

6. and open systems – steady and unsteady flow

Heat Reservoir, source and sink. Heat Engine, 2

Downloaded From : www.EasyEngineering.net

Carnot cycle Reversed Carnot cycle, Performance. 3

Entropy change for - pure substance, ideal gases - 2 T1,

Applications of II Law. High and low grade energy. 3

Expressions for the energy of a closed system and 2

asy Cumulative Hrs. 24

Binary and Combined cycles. 2 T1,

Downloaded From : www.EasyEngineering.net

IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS

Properties of Ideal gas- Ideal and real gas comparison- 3

Compressibility factor-.Principle of Corresponding 2 T1,

asy Cumulative Hrs

Unit- Psychrometric properties, Psychrometric charts. 3 .ne

Downloaded From : www.EasyEngineering.net

1. Nag.P.K., “Engineering Thermodynamics”, 4thEdition, Tata McGraw-Hill, New

2. Natarajan E., "Engineering Thermodynamics: Fundamentals and Applications",

1. Cengel. Y and M.Boles, "Thermodynamics - An Engineering Approach", 7th

Downloaded From : www.EasyEngineering.net

BASIC CONCEPTS AND FIRST LAW

1. What is microscopic approach in thermodynamics? Nov/Dec-2013

Example: Heat transfer, work transfer.

5. Enlist the similarities between work and heat. Nov/Dec-2014

Downloaded From : www.EasyEngineering.net

ww v) Both work and heat are path functions

Heat is a form of energy in transit. It is a boundary phenomenon, since it occurs only

Downloaded From : www.EasyEngineering.net

9. Define the Zeroth law of thermodynamics. April/May-2015,2016

In thermodynamics, Work is said to be done by a system if the sole effect on things

f) Enthalpy per unit mass. En

Downloaded From : www.EasyEngineering.net