Scribd
Upload
140 views12 pages

Mobile To PC Interface

The document discusses interfacing a GSM mobile phone to a PC in order to send SMS messages from the PC. A GSM/GPRS modem, which can be a mobile phone, is connected to the PC and sends SMS messages when instructed by AT commands. The document provides details on connecting the mobile phone/modem to the PC, using AT commands to control the device, and sending and receiving SMS messages through the phone/modem from the PC.

Uploaded by

dineshnagar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
140 views12 pages

Mobile To PC Interface

The document discusses interfacing a GSM mobile phone to a PC in order to send SMS messages from the PC. A GSM/GPRS modem, which can be a mobile phone, is connected to the PC and sends SMS messages when instructed by AT commands. The document provides details on connecting the mobile phone/modem to the PC, using AT commands to control the device, and sending and receiving SMS messages through the phone/modem from the PC.

Uploaded by

dineshnagar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 12

INTERFACING GSM MOBILE TO

PC TO SEND THE SMS FROM PC


The SMS specification has defined a way for a computer
to send SMS messages through a mobile phone or
GSM/GPRS modem. A GSM/GPRS modem is a wireless
modem that works with GSM/GPRS wireless networks. A
wireless modem is similar to a dial-up modem. The main
difference is that a wireless modem transmits data
through a wireless network whereas a dial-up modem
transmits data through a copper telephone line. Most
mobile phones can be used as a wireless modem.
However, some mobile phones have certain limitations
comparing to GSM/GPRS modems.
To send SMS messages, first place a valid SIM card from a
wireless carrier into a mobile phone or GSM/GPRS
modem, which is then connected to a computer. There
are several ways to connect a mobile phone or
GSM/GPRS modem to a computer. For example, they can
be connected through a serial cable, a USB cable, a
Bluetooth link or an infrared link. The actual way to use
depends on the capability of the mobile phone or
GSM/GPRS modem. For example, if a mobile phone does
not support Bluetooth, it cannot connect to the
computer through a Bluetooth link.
After connecting a mobile phone or GSM/GPRS modem
to a computer, you can control the mobile phone or
GSM/GPRS modem by sending instructions to it. The
instructions used for controlling the mobile phone or
GSM/GPRS modem are called AT commands. (AT
commands are also used to control dial-up modems for
wired telephone system.) Dial-up modems, mobile
phones and GSM/GPRS modems support a common set
of standard AT commands. In addition to this common
set of standard AT commands, mobile phones and
GSM/GPRS modems support an extended set of AT
commands. One use of the extended AT commands is to
control the sending and receiving of SMS messages.

INTRODUCTION-:
The project is aimed at developing and testing the use of
mobile phones to remotely control an appliance control
system. The microcontroller would then control an
device based on the information given to it. The
proposed solution will need to be easy to use, simple,
secure, robust and be useful on most mobile phones. To
achieve this testing will need to be carried out to create a
useful system.
The report consists of a background into the area of 8051
microcontroller and mobile communication, how they
are interfaced to each other and AT (Attention)
commands set used in communication.

HARDWARE USED

1. AT command supporting GSM mobile phone.


2. 89S52 Microcontroller
3. Max 232 IC.
4. Relays
5. Relay driver IC ULN 2803
6. Voltage regulator 7805.
7. Diode IN4007
8. GSM Phone

SOFTWARE USED
1. Keil u-Vision 3.0

Keil Software is used provide you with software


development tools for 8051 based microcontrollers. With
the Keil tools, you can generate embedded applications
for virtually every 8051 derivative. The supported
microcontrollers are listed in the µ-vision

2 PRO51 Programmer Software

THEORY OF OPERATION

In this project we interfaced 8051 microcontroller with


Motorola’s C168 GSM mobile phone to decode the
received message and do the required action. The
protocol used for the communication between the two is
AT command.
The microcontroller pulls the SMS received by phone,
decode it, recognizes the
Mobile no. and then switches on the relays attached to
its port to control the appliances. After successful
operation, controller sends back the acknowledgement
to the user’s mobile through SMS.

AT-Command set
The following section describes the AT-Command set.
The commands can be tried out by connecting a GSM
modem to one of the PC’s COM ports. Type in the test-
command, adding CR + LF (Carriage return + Line feed
= \r\n) before executing. Table gives an overview of the
implemented AT-Commands in this application. The use
of the commands is described in the later sections.

AT-Command set overview

Command Description
Check if serial interface and
AT GSM modem is working.
Turn echo off, less traffic
ATE0 on serial line.
Display of new incoming
AT+CNMI SMS.
AT+CPMS Selection of SMS memory.
SMS string format, how
AT+CMGF they are compressed.
Read new message from a
AT+CMGR given memory location.
Send message to a given
AT+CMGS recipient.
AT+CMGD Delete message.
A BRIEF INTRODUCTION TO 8051 MICROCONTROLLER: 
When we have to learn about a new computer we
have to familiarize about the machine capability we are
using, and we can do it by studying the internal hardware
design (devices architecture), and also to know about the
size, number and the size of the registers.
         A microcontroller is a single chip that contains the
processor (the CPU), non-volatile memory for the
program (ROM or flash), volatile memory for input and
output (RAM), a clock and an I/O control unit. Also called
a "computer on a chip," billions of microcontroller units
(MCUs) are embedded each year in a myriad of products
from toys to appliances to automobiles. For example, a
single vehicle can use 70 or more microcontrollers. The
following picture describes a general block diagram of
microcontroller.

89s52: The AT89S52 is a low-power, high-performance


CMOS 8-bit microcontroller with 8K bytes of in-system
programmable Flash memory. The device is
manufactured using Atmel’s high-density nonvolatile
memory technology and is compatible with the industry-
standard 80C51 instruction set and pinout. The on-chip
Flash allows the program memory to be reprogrammed
in-system or by a conventional nonvolatile memory pro-
grammer. By combining a versatile 8-bit CPU with in-
system programmable Flash on a monolithic chip, the
Atmel AT89S52 is a powerful microcontroller, which
provides a highly flexible and cost-effective solution to
many, embedded control applications. The AT89S52
provides the following standard features: 8K bytes of
Flash, 256 bytes of RAM, 32 I/O lines, Watchdog timer,
two data pointers, three 16-bit timer/counters, a six-
vector two-level interrupt architecture, a full duplex
serial port, on-chip oscillator, and clock circuitry. In
addition, the AT89S52 is designed with static logic for
operation down to zero frequency and supports two
software selectable power saving modes. The Idle Mode
stops the CPU while allowing the RAM, timer/counters,
serial port, and interrupt system to continue functioning.
The Power-down mode saves the RAM con-tents but
freezes the oscillator, disabling all other chip functions
until the next interrupt
The hardware is driven by a set of program instructions,
or software. Once familiar with hardware and software,
the user can then apply the microcontroller to the
problems easily.
    The pin diagram of the 8051 shows all of the
input/output pins unique to microcontrollers:

The following are some of the capabilities of 8051


microcontroller.
 Internal ROM and RAM
 I/O ports with programmable pins
 Timers and counters
 Serial data communication
The 8051 architecture consists of these specific features:
 16 bit PC &data pointer (DPTR)
 8 bit program status word (PSW)
 8 bit stack pointer (SP)
 Internal ROM 4k
 Internal RAM of 128 bytes.
 4 register banks, each containing 8
registers
 80 bits of general purpose data memory
 32 input/output pins arranged as four 8
bit ports: P0-P3
 Two 16 bit timer/counters: T0-T1
 Two external and three internal interrupt
sources Oscillator and clock circuits.

BLOCK DIAGRAM OF PROJECT

You might also like