Duke 390 Repair Manual (Full Version - 204pages)

REPAIR MANUAL 2013
390 Duke EU 390 Duke AUS 390 Duke MAL 390 Duke 2014
COL
Art. no. 3206167en

INTRODUCTION
1
INTRODUCTION It is important that you read this repair manual carefully and completely before the start of work.
This vehicle can only fulfill the demands placed on it in the long run if the specified service work is performed regularly by
qualified experts.
The repair manual was written to correspond to the most current state of this model series. We reserve the right to make changes
in the interest of technical advancement without, at the same time, updating this repair manual. We shall not provide a description
of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here. It is assumed that repair
work will be performed by a fully trained mechanic.
All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical
specifications, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying
reasons, to adapt these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts
no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors. The models
portrayed partly contain special equipment that does not belong to the regular scope of supply.
© 2013 KTM-Sportmotorcycle AG, Mattighofen Austria All rights reserved Reproduction, even in part, as well as copying of all
kinds, is permitted only with the express written permission of the copyright owner.
ISO 9001(12 100 6061) According to the international quality management standard ISO 9001, KTM uses quality assurance
processes that lead to the maximum possible quality of the products. Issued by: TÜV Management Service
KTM-Sportmotorcycle AG 5230 Mattighofen, Austria

TABLE OF CONTENTS
2
TABLEOFCONTENTS 1 MEANS OF REPRESENTATION ..................................... 5 1.1 Symbols
used................................................... 5 1.2 Formats used.................................................... 5 2 SAFETY
ADVICE........................................................... 6 2.1 Repair Manual.................................................. 6 2.2 Safety
advice.................................................... 6 2.3 Degrees of risk and symbols............................... 6 2.4 Work
rules........................................................ 6 3 IMPORTANT INFORMATION ......................................... 7 3.1 Guarantee, warranty
.......................................... 7 3.2 Operating and auxiliary substances..................... 7 3.3 Spare parts, accessories
.................................... 7 3.4 Figures ............................................................ 7 4 SERIAL NUMBERS
...................................................... 8 4.1 Chassis number/type label ................................. 8 4.2 Key
number...................................................... 8 4.3 Engine number ................................................. 8 5 MOTORCYCLE
............................................................. 9
5.1 Raising the motorcycle with the rear wheel
stand............................................................... 9 5.2 Taking the motorcycle off of the rear wheel
stand............................................................... 9 5.3 Raising the motorcycle with the front wheel
stand............................................................... 9 5.4 Taking the motorcycle off of the front wheel
stand............................................................. 10 5.5 Raising the motorcycle with the work stand ....... 10 5.6 Removing the
motorcycle from the work stand ... 11 5.7 Starting.......................................................... 12 5.8 Starting the motorcycle to make
checks ............ 13 6 FORK, TRIPLE CLAMP ............................................... 14 6.1 Cleaning the dust boots of the fork
legs............. 14 6.2 Removing fork legs.......................................... 14 6.3 Installing the fork legs..................................... 15 6.4
Disassembling the fork legs.............................. 16 6.5 Checking the fork legs..................................... 18 6.6 Assembling the fork
legs.................................. 19 6.7 Removing the lower triple clamp....................... 21 6.8 Installing the lower triple clamp
....................... 23 6.9 Checking the steering head bearing play............ 26 6.10 Adjusting the steering head bearing play ........... 26
7 HANDLEBAR, CONTROLS........................................... 28 7.1 Checking the play in the throttle cable.............. 28 7.2
Adjusting the play in the throttle cable.............. 28 7.3 Checking the clutch lever play.......................... 28 7.4 Adjusting the clutch
cable play ........................ 29 8 SHOCK ABSORBER, SWINGARM ................................ 30
8.1 Adjusting the spring preload of the shock
absorber......................................................... 30 8.2 Removing the shock absorber........................... 30 8.3 Installing the shock
absorber............................ 30 8.4 Removing the spring........................................ 31 8.5 Installing the spring
........................................ 31 9 EXHAUST.................................................................. 33 9.1 Removing the exhaust
manifold........................ 33 9.2 Installing the exhaust manifold ........................ 34 9.3 Removing the main silencer
............................. 35 9.4 Installing the main silencer.............................. 36 10 AIR FILTER
............................................................... 37 10.1 Removing the air filter..................................... 37 10.2 Installing the air
filter...................................... 37
11 FUEL TANK, SEAT, TRIM ........................................... 38 11.1 Opening the filler cap...................................... 38 11.2
Closing the filler cap ....................................... 38 11.3 Removing the seat .......................................... 38 11.4 Mounting the
seat........................................... 39 11.5 Removing the passenger seat ........................... 39 11.6 Mounting the passenger
seat............................ 39 11.7 Removing the fuel tank cover ........................... 39 11.8 Installing the fuel tank
cover............................ 42 11.9 Removing the fuel tank.................................... 44 11.10 Installing the fuel tank
.................................... 45 11.11 Removing the front spoiler............................... 47 11.12 Fitting front spoiler
......................................... 47 11.13 Dismounting the front fender ........................... 48 11.14 Installing the front fender
................................ 48 11.15 Checking the fuel pressure............................... 48 11.16 Changing the fuel
filter.................................... 49 11.17 Replacing the fuel pump ................................. 51 12 WHEELS
................................................................... 52 12.1 Checking the tire air pressure........................... 52 12.2 Checking the tire
condition .............................. 52 12.3 Checking the brake discs................................. 53 12.4 Front wheel
.................................................... 53 12.4.1 Removing the front wheel ............................ 53 12.4.2 Installing the front
wheel............................. 53 12.4.3 Removing the brake disc of the front brake.... 54 12.4.4 Installing the brake disc of the front
brake .... 54 12.5 Rear wheel ..................................................... 55 12.5.1 Removing the rear wheel ............................. 55 12.5.2
Installing the rear wheel .............................. 55 12.5.3 Removing the brake disc of the rear brake..... 56 12.5.4 Installing the brake
disc of the rear brake...... 56 12.5.5 Checking the chain tension.......................... 57 12.5.6 Adjusting the chain tension
......................... 57 12.5.7 Checking the chain, rear sprocket, and
engine sprocket .......................................... 58 12.5.8 Cleaning the chain...................................... 59 12.5.9 Checking the rear hub
rubber dampers.......... 60 13 WIRING HARNESS, BATTERY..................................... 61 13.1 Removing the battery
...................................... 61 13.2 Installing the battery ....................................... 61 13.3 Disconnecting the negative cable of the
battery........................................................... 62 13.4 Reconnecting the negative cable of the
battery........................................................... 62 13.5 Recharging the battery .................................... 62 13.6 Checking the
charging voltage.......................... 63 13.7 Changing the fuses of individual power
consumers...................................................... 64 14 BRAKE SYSTEM ........................................................ 65 14.1 Checking the
front brake linings....................... 65 14.2 Changing the front brake linings....................... 65 14.3 Checking the brake fluid level
of the front
brake............................................................. 67 14.4 Adding front brake fluid................................... 67 14.5 Changing the
front brake fluid.......................... 68 14.6 Checking the rear brake linings ........................ 69 14.7 Changing the rear brake linings
........................ 70 14.8 Checking the free travel of foot brake lever ........ 71 14.9 Adjusting the free travel of the foot brake
lever .............................................................. 72 14.10 Checking the rear brake fluid level.................... 72

TABLE OF CONTENTS
3
14.11 Adding rear brake fluid.................................... 73 14.12 Changing the rear brake fluid ........................... 73 15 LIGHTING
SYSTEM, INSTRUMENTS ........................... 75 15.1 Setting kilometers or miles............................... 75 15.2 Adjusting the shift
speed RPM 1 ...................... 75 15.3 Adjusting the shift speed RPM 2 ...................... 75 15.4 Setting the
time.............................................. 76 15.5 Resetting the service interval display ................ 76 15.6 Checking the headlight setting
......................... 76 15.7 Adjusting the headlight range........................... 77 15.8 Changing the parking light bulb........................ 78
15.9 Changing the headlight bulb ............................ 79 16 ENGINE .................................................................... 81 16.1 Removing
the engine....................................... 81 16.2 Installing the engine........................................ 85 16.3 Disassembling the engine
................................ 90 16.3.1 Preparations............................................... 90 16.3.2 Draining the engine oil ................................ 90
16.3.3 Removing the chain securing guide .............. 90 16.3.4 Removing the valve cover............................. 91 16.3.5 Removing
the spark plug ............................. 91 16.3.6 Removing the clutch cover........................... 91 16.3.7 Setting the engine to ignition
top dead
center........................................................ 92 16.3.8 Removing the timing chain tensioner ............ 93 16.3.9 Removing
the camshaft............................... 93 16.3.10 Removing the cylinder head......................... 94 16.3.11 Removing the piston
................................... 95 16.3.12 Removing the starter motor.......................... 95 16.3.13 Removing the timing chain
.......................... 95 16.3.14 Removing the water pump wheel .................. 96 16.3.15 Removing the alternator cover......................
96 16.3.16 Removing the rotor...................................... 97 16.3.17 Removing the starter drive ........................... 97 16.3.18
Removing the balancer shaft drive wheel....... 98 16.3.19 Removing the gear position sensor................ 98 16.3.20 Removing the
suction pump......................... 99 16.3.21 Removing the spacer................................. 100 16.3.22 Removing the clutch
cage.......................... 100 16.3.23 Removing the primary gear ........................ 101 16.3.24 Removing the force
pump.......................... 102 16.3.25 Removing the shift shaft............................ 103 16.3.26 Removing the shift drum
locating............... 103 16.3.27 Removing the locking lever ........................ 103 16.3.28 Removing the oil filter...............................
103 16.3.29 Removing the left engine case.................... 104 16.3.30 Removing the shift rails............................. 105 16.3.31
Removing the shift drum ........................... 105 16.3.32 Removing the shift forks............................ 106 16.3.33 Removing the
transmission shafts............... 106 16.3.34 Removing the balancer shaft...................... 106 16.3.35 Removing the crankshaft
........................... 106 16.4 Work on individual parts ................................ 107 16.4.1 Work on the left section of the engine
case ........................................................ 107 16.4.2 Work on the right section of the engine
case ........................................................ 108 16.4.3 Changing the shaft seal ring of the water
pump ...................................................... 108 16.4.4 Checking the radial play of the lower
conrod bearing ......................................... 109 16.4.5 Changing the conrod bearing...................... 110
16.4.6 Changing the balancer shaft bearing........... 111 16.4.7 Work on the cylinder head ......................... 112 16.4.8 Checking the
cylinder head........................ 113 16.4.9 Checking the pivot point of the
camshafts ................................................ 113 16.4.10 Checking/measuring the cylinder ................ 114 16.4.11
Checking the piston ring end gap ............... 114 16.4.12 Checking/measuring the piston................... 115 16.4.13 Checking the
piston/cylinder mounting
clearance................................................. 115 16.4.14 Checking the oil pump .............................. 115 16.4.15 Checking
the oil pressure regulator valve..... 116 16.4.16 Checking the clutch.................................. 117 16.4.17 Checking the shift
mechanism ................... 118 16.4.18 Preassembling the shift shaft..................... 119 16.4.19 Disassembling the main shaft
.................... 119 16.4.20 Dismantling the countershaft ..................... 120 16.4.21 Checking the transmission......................... 120
16.4.22 Assembling the main shaft......................... 121 16.4.23 Assembling the countershaft...................... 122 16.4.24 Checking
the timing assembly.................... 124 16.4.25 Changing the stator................................... 124 16.4.26 Checking the electric starter
drive .............. 125 16.4.27 Checking the freewheel ............................. 126 16.5 Assembling the engine .................................. 126
16.5.1 Installing the crankshaft............................ 126 16.5.2 Installing the balancer shaft....................... 126 16.5.3 Installing the
transmission shafts ............... 127 16.5.4 Installing the shift forks............................. 127 16.5.5 Installing the shift
drum............................ 127 16.5.6 Installing the shift rails ............................. 127 16.5.7 Installing the left engine case
.................... 128 16.5.8 Installing the oil filter................................ 129 16.5.9 Installing the locking lever......................... 129
16.5.10 Installing the shift drum locating................ 130 16.5.11 Installing the shift shaft ............................ 130 16.5.12 Installing
the oil pump .............................. 130 16.5.13 Installing the primary gear ......................... 131 16.5.14 Installing the clutch cage
.......................... 132 16.5.15 Installing the spacer.................................. 133 16.5.16 Installing the suction pump .......................
134 16.5.17 Installing the gear position sensor .............. 135 16.5.18 Installing the balancer shaft drive wheel ..... 135 16.5.19
Installing the starter drive.......................... 136 16.5.20 Installing the rotor .................................... 137 16.5.21 Installing the
alternator cover..................... 137 16.5.22 Installing the water pump cover.................. 137 16.5.23 Installing the timing
chain......................... 138 16.5.24 Installing the starter motor......................... 138 16.5.25 Installing the
piston.................................. 138 16.5.26 Installing the cylinder head........................ 140 16.5.27 Installing the camshafts
............................ 141 16.5.28 Installing the timing chain tensioner........... 141 16.5.29 Checking the valve clearance .....................
142 16.5.30 Adjusting the valve clearance..................... 143 16.5.31 Installing the clutch cover ......................... 143 16.5.32
Installing the spark plug............................ 144 16.5.33 Installing the valve cover ........................... 144 16.5.34 Installing the chain
securing guide ............. 145 16.5.35 Installing the oil screen............................. 145 16.5.36 Removing the engine from the engine
assembly stand......................................... 146

TABLE OF CONTENTS
4
17 SHIFT MECHANISM................................................. 147 17.1 Adjusting the shift lever................................. 147 18 WATER
PUMP, COOLING SYSTEM ............................ 148 18.1 Draining the coolant...................................... 148 18.2 Filling/bleeding
the cooling system ................. 148 18.3 Checking the antifreeze and coolant level........ 149 18.4 Checking the coolant level
............................. 150 19 LUBRICATION SYSTEM............................................ 152 19.1 Oil
circuit..................................................... 152 19.2 Checking the engine oil level.......................... 152 19.3 Checking the engine oil
pressure .................... 152 19.4 Changing the engine oil and oil filter,
cleaning the oil screen................................... 154 19.5 Adding engine oil.......................................... 155 20 IGNITION
SYSTEM................................................... 156 20.1 Alternator - checking the stator winding .......... 156 21 TECHNICAL
DATA.................................................... 157 21.1 Engine......................................................... 157 21.2 Engine tolerance, wear
limits ......................... 157 21.3 Engine tightening torques.............................. 158 21.4 Capacities....................................................
159 21.4.1 Engine oil ................................................ 159 21.4.2 Coolant.................................................... 159 21.4.3 Fuel
........................................................ 159 21.5 Chassis ........................................................ 159 21.6 Electrical
system........................................... 160 21.7 Tires............................................................ 160 21.8
Fork............................................................. 160 21.9 Shock absorber............................................. 160 21.10 Chassis tightening
torques ............................. 161 22 CLEANING/PROTECTIVE TREATMENT....................... 163 22.1 Cleaning the motorcycle
................................ 163 22.2 Checks and maintenance steps for winter
operation...................................................... 164 23 STORAGE................................................................ 165 23.1 Storage
........................................................ 165 23.2 Preparing for use after storage........................ 165 24 SERVICE SCHEDULE
............................................... 166 24.1 Service schedule........................................... 166 25 WIRING DIAGRAM
................................................... 168 25.1 Page 1 of 9 .................................................. 168 25.2 Page 2 of 9
.................................................. 170 25.3 Page 3 of 9 .................................................. 172 25.4 Page 4 of 9
.................................................. 174 25.5 Page 5 of 9 .................................................. 176 25.6 Page 6 of 9
.................................................. 178 25.7 Page 7 of 9 .................................................. 180 25.8 Page 8 of 9
.................................................. 182 25.9 Page 9 of 9 .................................................. 184 26 SUBSTANCES
......................................................... 186 27 AUXILIARY SUBSTANCES ........................................ 187 28 SPECIAL TOOLS
...................................................... 189 29 STANDARDS ........................................................... 198
INDEX............................................................................ 199

1 MEANS OF REPRESENTATION
5
1.1 Symbols used

The meaning of specific symbols is described below.
Indicates an expected reaction (e.g. of a work step or a function).
Indicates an unexpected reaction (e.g. of a work step or a function).
Indicates a page reference (more information is provided on the specified page).
Indicates information with more details or tips.
Indicates the result of a testing step.
Denotes a resistance measurement.
1.2 Formats used

The typographical formats used in this document are explained below.
Proprietary name Identifies a proprietary name.
Name® Identifies a protected name.
BrandTM Identifies a trademark.
Denotes a voltage measurement.
Denotes a current measurement.

2 SAFETY ADVICE
6
2.1 Repair Manual

Read this Repair Manual carefully and thoroughly before beginning work. It contains useful information and tips that will help
you repair and maintain your vehicle. This manual assumes that the necessary special KTM tools and KTM workplace and
workshop equipment are available.
2.2 Safety advice

A number of safety instructions need to be followed to operate the vehicle safely. Therefore, read this manual carefully. The
safety instructions are highlighted in the text and are referred to at the relevant passages.
Info The vehicle has various information and warning labels at prominent locations. Do not remove information/warning labels.
If they are missing, you or others may not recognize dangers and may therefore be injured.
2.3 Degrees of risk and symbols

Danger Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate
measures are not taken.
Warning Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.
Caution Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.
Note Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.
Warning Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.
2.4 Work rules

Special tools are necessary for certain tasks. The tools are not contained in the vehicle but can be ordered under the number in
paren- theses. E.g.: bearing puller (15112017000) During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals
and seal rings, O-rings, pins, lock washers) must be replaced by new parts. In some instances, a thread locker (e.g. Loctite®) is
required. The manufacturer instructions for use must be followed. After disassembly, clean the parts that are to be reused and
check them for damage and wear. Change damaged or worn parts. After you complete the repair or service work, check the
operating safety of the vehicle.

3 IMPORTANT INFORMATION
7
3.1 Guarantee, warranty

The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the
customer's Service & Warranty Booklet and in the KTM dealer.net; otherwise, all warranty claims will be void. No warranty
claims can be consid- ered for damage resulting from manipulations and/or alterations to the vehicle. Additional information on
the guarantee or warranty and the procedures involved can be found in the Service & Warranty Booklet.
3.2 Operating and auxiliary substances

Warning Environmental hazard Improper handling of fuel is a danger to the environment.
– Do not allow fuel to get into the ground water, the ground, or the sewage system.
Use the operating and auxiliary substances (such as fuel and lubricants) as specified in the manual.
3.3 Spare parts, accessories

Only use spare parts and accessories approved and/or recommended by KTM. KTM accepts no liability for other products and
any resulting damage or loss.
The current KTM PowerParts for your vehicle can be found on the KTM website. International KTM Website:
http://www.ktm.com
3.4 Figures
The figures contained in the manual may depict special equipment. In the interest of clarity, some components may be shown
disassembled or may not be shown at all. It is not always necessary to dis- assemble the component to perform the activity in
question. Please follow the instructions in the text.

4 SERIAL NUMBERS
8
4.1 Chassis number/type label

The chassis number is stamped on the right of the steering head. The type label is on the right of the frame behind the steering
head.
4.2 Key number

The key number can be found on the KEYCODECARD.
Info You need the key number to order a spare key. Keep the KEYCODECARD in a safe place.
4.3 Engine number

B00755-10
101877-10
101876-10
The engine number is stamped on the left side of the engine under the engine sprocket.

5 MOTORCYCLE
9
5.1 Raising the motorcycle with the rear wheel stand

Note Danger of damage The parked vehicle may roll away or fall over.
– Always place the vehicle on a firm and even surface.
– Mount the support of the wheel stand. – Insert the adapter in the rear wheel stand.
Adapter (61029055130) ( p. 190) Rear wheel stand (61029055400) ( p. 191)
– Stand the motorcycle upright, align the lifting gear with the swingarm and the
adapters, and lift the motorcycle.
5.2 Taking the motorcycle off of the rear wheel stand

– Secure the motorcycle against falling over. – Remove the rear wheel stand and lean the vehicle on the side stand . – Remove the
support of the wheel stand.
5.3 Raising the motorcycle with the front wheel stand

Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9)
B01387-01
101884-10
101887-10
Condition
– Remove cap .

5 MOTORCYCLE
10
– Move the handlebar to the straight-ahead position. Attach the lifting gear to the
steering stem.
Adapter (61029955620) ( p. 191) Front wheel stand (61029055500) ( p. 191)
Info Always raise the rear of the motorcycle first.
– Raise the front of the motorcycle.
5.4 Taking the motorcycle off of the front wheel stand

– Mount cap .
5.5 Raising the motorcycle with the work stand

101888-01
101889-01
101887-10
308227-10
– Secure the motorcycle against falling over. – Remove the front wheel stand.
– Remove screw .

5 MOTORCYCLE
11
– Position the motorcycle upright, align the special tool and raise the motorcycle.
5.6 Removing the motorcycle from the work stand

308228-10
308229-10
308230-10
308231-10
308231-11
– Mount special tool on the right side of the vehicle.
Work stand (62529055000) ( p. 192)
– Remove screw !.
– Mount special tool on the left side of the vehicle.
Work stand (62529055000) ( p. 192)
– Secure the motorcycle against falling over. – Remove special tool .

5 MOTORCYCLE
12
– Mount and tighten screws !.
Guideline
Screw, engine bearer on frame M8 30 Nm
(22.1 lbf ft)
5.7 Starting
Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death.
– When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed
space without an effective exhaust extraction system.
Caution Danger of accidents If the vehicle is operated with a discharged battery or without a battery, electronic components and
safety equipment may be damaged.
– Never operate the vehicle with a discharged battery or without a battery.
Note Engine failure Unfiltered intake air has a negative effect on the service life of the engine.
– Never ride the vehicle without an air filter since dust and dirt can get into the engine and result in increased wear.
Note Engine failure High engine speeds in cold engines have a negative effect on the service life of the engine.
– Always warm up the engine at low engine speeds.
B00782-10
– Sit on the vehicle, take the weight off of the side stand, and move up all the way. – Turn the emergency OFF switch to the
position . – Switch on the ignition by turning the ignition key to the position .
After you switch on the ignition, you can hear the fuel pump working for about two seconds. The function check of the
combination instrument is run at the same time. – Shift gear to neutral.
The green idling speed indicator lamp N lights up. The ABS warning lamp lights up and goes back out after starting off. – Press
the electric starter button .
Info Do not press the electric starter button until the combination instrument function check is finished. When starting, DO NOT
open the throttle. If you open the throttle during the starting procedure, fuel is not injected by the engine management system and
the engine cannot start. Press the starter for a maximum of 5 seconds. Wait for a least 5 seconds before trying again. This
motorcycle is equipped with a safety starting system. You can only start the engine if the transmission is in neutral or if the clutch
is pulled when a gear is engaged. If the side stand is folded out and you shift into gear and release the clutch, the engine stops.
308232-10

5 MOTORCYCLE
13
Switching off ABS
KTM recommends riding with ABS at all times. However, situations may arise in which ABS is not advantageous. Condition
Vehicle stationary, engine running. – Press the button for 3 – 5 seconds.
The ABS warning lamp starts flashing; ABS is deactivated.
401685-15
5.8 Starting the motorcycle to make checks

– When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed
space without an effective exhaust extraction system.
Info Press the starter for a maximum of 5 seconds. Wait for a least 5 seconds before trying again.
B00782-10
– Turn the emergency OFF switch to the position . – Shift gear to neutral. – Switch on the ignition by turning the ignition key to
the position . – Press the electric starter button .
Info Do not open the throttle.

6 FORK, TRIPLE CLAMP
14
6.1 Cleaning the dust boots of the fork legs

– Push dust boot of both fork legs downwards.
Info The dust boots should remove dust and coarse dirt particles from the fork tubes. Over time, dirt can penetrate behind the dust
boots. If this dirt is not removed, the oil seals behind can start to leak.
Warning Danger of accidents Reduced braking efficiency due to oil or grease on the 308233-10
brake discs. – Always keep the brake discs free of oil and grease, and clean them with
brake cleaner when necessary.
– Clean and oil the dust boots and inside fork tube of both fork legs.
Universal oil spray ( p. 188)
– Press the dust boots back into their normal position. – Remove excess oil.
6.2 Removing fork legs

Preparatory work – Raise the motorcycle with the work stand. ( p. 10) – Tie the rear of the vehicle down. – Dismount the front
fender. ( p. 48)
308235-10
308236-10
308237-10
Main work – Remove screw . – Remove the cable binder. – Pull off the ABS sensor and hang it to one side.
– Remove screws . – Press back the brake linings with a light lateral tilting of the brake caliper on the
brake disc. Pull the brake caliper carefully back from the brake disc and hang it to one side.
Info Do not pull the hand brake lever when the brake caliper has been removed.
– Loosen screws ! and screw ". – Unscrew screw ! about six turns and press your hand on the screw to push the
wheel spindle out of the axle clamp. Remove screw !.
Warning Danger of accidents Reduced braking effect caused by damaged brake discs. – Always lay the wheel down in such a
way that the brake discs are not
damaged.
– Holding the front wheel, withdraw the wheel spindle. Take the front wheel out of
the fork.

15
– Loosen screws #. Remove the fork legs from the bottom.
308238-10
6.3 Installing the fork legs

Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior.
– Following modifications, ride slowly at first to get the feel of the new ride behavior.
308239-10
308238-11
308240-10
308237-11
Main work – Push the fork legs into the triple clamps. – Align the fork legs in the required position using the fork rings.
– Tighten screws .
Guideline
Screw, top triple clamp M8 11 Nm (8.1 lbf ft)
Guideline
Screw, bottom triple clamp M8 15 Nm
(11.1 lbf ft)
– Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:
– Change the wheel bearing. – Clean and grease the shaft seal rings ! and contact surfaces ( of the spacers.
Long-life grease ( p. 187)
– Clean screw " and the wheel spindle. – Lift the front wheel into the fork, position it, and insert the wheel spindle. – Mount and
tighten screw ".
Guideline
Screw, front wheel spindle M8 30 Nm
(22.1 lbf ft)

16
– Pull the front brake and compress the fork powerfully a few times.
The fork legs straighten. – Tighten screws %.
Guideline
Screw, fork stub M8 15 Nm
(11.1 lbf ft)
Finishing work – Install front fender. ( p. 48)
6.4 Disassembling the fork legs

Info These operations are the same on both fork legs.
Condition The fork legs have been removed.
308236-11
308235-11
308241-10
201505-10
– Position the brake calipers and check that the brake linings are seated correctly. – Mount screws # but do not tighten yet. –
Operate the hand brake lever repeatedly until the brake linings are in contact with
the brake disc and there is a pressure point. Fix the hand brake lever in the activated position.
The brake calipers straighten. – Tighten screws #.
Guideline
Screw, front brake caliper M8x1 27 Nm
(19.9 lbf ft)
Loctite® 243TM
– Remove the fixation of the hand brake lever. – Unload the rear of the vehicle. – Remove the motorcycle from the work stand. (
p. 11)
– Position the ABS sensor. – Mount and tighten screw $.
Guideline
Screw, wheel speed sensor holder M6 8 Nm (5.9 lbf ft)
– Route the cable and secure with a cable binder.
– Clamp the fork leg in the area of the lower triple clamp.
Clamping stand (T612S) ( p. 197)

17
201506-10
201507-10
201508-10
201509-10
201510-10
201511-10
– Loosen the screw cap .
Info The screw cap cannot be removed yet.
– Empty the fork oil.
– Release the fork leg and clamp it with the fork stub.
Info Use soft jaws.
– Push the outer tube downward. – Hold screw cap . Loosen nut . Remove the screw cap.
– Detach the outer tube from the inner tube.
Info Place a container underneath to catch any oil that may run out.
– Unclamp the inner tube. Drain the oil.

18
– Unclamp the outer tube. – Heat up the outer tube in the area of sliding bushing %.
Guideline
50 °C (122 °F)
– Strike the lower edge of the outer fork tube on a wooden board.
Sliding bushing % must fall out of its seat.
6.5 Checking the fork legs

Condition The fork legs have been disassembled.
201512-10
201513-10
201514-10
201515-10
201516-10
– Clamp the outer tube in the area of the lower triple clamp.
– Remove dust boot !.
– Remove lock ring ".
Info The lock ring has a beveled end where a screwdriver can be applied.
– Remove seal ring #. Remove support ring $.
– Check the inner tube and the axle clamp for damage.
» If damage is found:
– Change the fork leg.

19
– Check the surface of the sliding bushings.
» If the dark layer ( is worn off:
6.6 Assembling the fork legs

Info These operations are the same on both fork legs.
Preparatory work – Check the fork legs. ( p. 18)
200684-10
200685-10
200632-10
201517-10
202092-10
– Measure the outside diameter of the inner tube in several places.
External diameter of inner tube 42.975... 43.005 mm (1.69193...
1.69311 in)
» If the measured value is less than the specified value:
– Measure the run-out of the inner tube.
Run-out of inner tube ≤ 0.20 mm (≤ 0.0079 in)
» If the measured value is greater than the specified value:
– Check the outer tube for damage.
» If damage is found:
Main work – Clamp in the inner tube with the axle clamp.
Guideline
Use soft jaws.
– Grease and slide on dust boot .
Lubricant (T511) ( p. 187)
Info Always change the dust boot, lock ring, seal ring, and support ring. Install the dust boot with the sealing lip and spring
expander facing downward.

20
– Slide on lock ring . – Grease and slide on seal ring !.
Lubricant (T511) ( p. 187)
Info Mount with the sealing lip facing down and the open side facing up.
– Slide on support ring ". – Sand the edges of sliding bushing # with 600-grit sandpaper, then clean and
grease.
Fork oil (SAE 4) (48601166S1) ( p. 186)
– Slide on sliding bushing #.
202093-10
202094-10
202095-10
202096-10
– Warm up the outer tube in the lower sliding bushing area (.
Guideline
50 °C (122 °F)
– Slide the outer tube onto the inner tube. – Hold the sliding bushing with the longer shoulder of the special tool.
Mounting tool (T528S) ( p. 197)
– Push the sliding bushing all the way into the outer tube.
– Position the support ring. – Hold the seal ring with the shorter shoulder of the special tool.
Mounting tool (T528S) ( p. 197)
– Push the seal ring and support ring all the way into the outer tube.
– Mount lock ring .
Info The lock ring must engage audibly.
– Install dust boot .

21
– Push the outer tube upward. – Mount screw cap $. – Unclamp the fork leg in the area of the lower triple clamp.
– Tighten the screw cap.
Guideline
Screw cap on outer tube M47x1.5 30 Nm
(22.1 lbf ft)
6.7 Removing the lower triple clamp

Preparatory work – Raise the motorcycle with the work stand. ( p. 10) – Tie the rear of the vehicle down. – Dismount the front
fender. ( p. 48) – Remove the fork legs. ( p. 14)
202097-10
201523-10
201522-10
308242-10
308243-10
– Mount screw cap $ onto the piston rod.
Info Nut % must be turned all the way down.
– Hold the screw cap and tighten the nut.
Guideline
Nut, piston rod on screw cap M12x1 30 Nm
(22.1 lbf ft)
– Fill it with fork oil.
Fork oil 450 ml
(15.21 fl. oz.)
Main work – Remove expanding rivets .
– Remove screws . – Lift the headlight mask slightly and swing forward.
Fork oil (SAE 4) (48601166S1)
( p. 186)
Info If it should be impossible to add the full quantity of oil, close the screw cap of the outer tube, unclamp the fork and bounce a
number of times. Then add the remaining quantity.

22
308244-10
308245-10
308246-10
308247-10
308248-10
308249-10
– Detach connectors ! and ".
– Detach connectors # and $.
– Remove the connector holder. – Disconnect connector %.
– Remove the combination instrument.
– Remove screws &. – Remove the headlight mask.
– Remove screw '.

23
– Remove washer 03. – Remove steering head bearing 04. – Remove the lower triple clamp with the steering stem.
6.8 Installing the lower triple clamp

308251-10
308252-10
308253-10
308254-10
308254-11
308253-11
– Remove the upper triple clamp with the handlebar and set aside.
Info Protect the vehicle and its attachments from damage by covering them.
– Expose the cable.
– Remove nut 02.
Castle nut wrench; 1⁄2" drive (90129050100) ( p. 195)
Main work – Clean the bearing and sealing elements, check for damage, and grease.
High viscosity grease ( p. 187)
– Insert the lower triple clamp with the steering stem. – Mount the upper steering head bearing . – Mount washer with the cut-out
facing downward.
Alternative 1
A new steering head bearing is used. – Mount and tighten nut !.

24
Guideline
Nut, steering head M30x1 Step 1 50 Nm (36.9 lbf ft) 2nd stage (loosen, counterclockwise) 2 turns Step 3 5 Nm (3.7 lbf ft)
Alternative 2
The steering head bearing is used again. – Mount and tighten nut !.
Guideline
Nut, steering head M30x1 5 Nm (3.7 lbf ft)
308252-10
308251-10
308250-10
308248-11
– Secure the cable in the bracket.
– Position the upper triple clamp with the handlebar.
– Mount screw " with the washer but do not tighten it yet.
Guideline
Screw, top steering head M16x1.5 52 Nm
(38.4 lbf ft)
Holding lugs ( reach into the drilled holes.
– Position the headlight mask. – Mount and tighten screw #.
Guideline
Screw, headlight mask M6 11 Nm (8.1 lbf ft)

25
308246-11
308245-11
308244-11
308243-11
308242-11
308255-10
– Position the combination instrument. – Plug in connector $. – Mount the connector holder %.
– Plug in connectors & and '.
– Plug in connectors 02 and 03.
– Fold the headlight mask up. – Mount and tighten screws 04.
Guideline
– Mount expanding rivets 05 on both sides. – Install the fork legs. ( p. 15)
– Loosen screws 06. – Using a plastic hammer, tap lightly on the upper triple clamp to avoid strains. – Tighten screw ".
Guideline
(38.4 lbf ft)
– Tighten screws 06.
Guideline

26
Finishing work – Check that the wiring harness, throttle cables, and brake line have the necessary
freedom of movement and are correctly routed. – Check the steering head bearing play. ( p. 26) – Remove the motorcycle
from the work stand. ( p. 11)
6.9 Checking the steering head bearing play

Warning Danger of accidents Unstable vehicle handling from incorrect steering head bearing play.
– Adjust the steering head bearing play without delay.
Info If the bike is ridden with play in the steering head bearing, the bearing and the bearing seats in the frame can become dam-
aged with time.
Preparatory work – Raise the motorcycle with the work stand. ( p. 10)
400738-11
Main work – Move the handlebar to the straight-ahead position. Move the fork legs to and fro in
the direction of travel.
No play should be noticeable in the steering head bearing.
» If there is noticeable play present:
– Adjust the play of the steering head bearing. ( p. 26) – Move the handlebar to and fro over the entire steering range.
The handlebar must be able to move easily over the entire steering range. No resting locations should be noticeable.
» If click positions are noticeable:
– Adjust the play of the steering head bearing. ( p. 26) – Check the steering head bearing and change if necessary. Finishing work
– Remove the motorcycle from the work stand. ( p. 11)
6.10 Adjusting the steering head bearing play

308256-10
308257-10
Main work – Loosen screws . – Loosen screw .
– Tighten nut ! with the special tool until there is no play in the steering head bear-
ing.
Key for steering head bearing (90129051000) ( p. 195)

27
308256-10
– Using a plastic hammer, tap lightly on the upper triple clamp to avoid strains. – Tighten screw .
Guideline
(38.4 lbf ft)
Guideline
Finishing work – Check the steering head bearing play. ( p. 26) – Remove the motorcycle from the work stand. ( p. 11)

7 HANDLEBAR, CONTROLS
28
7.1 Checking the play in the throttle cable

400192-10
– Check the throttle grip for smooth operation. – Move the handlebar to the straight-ahead position. Move the throttle grip back-
wards and forwards to ascertain the play in the throttle cable.
Throttle cable play 3... 5 mm (0.12... 0.2 in)
» If the throttle cable play does not meet specifications: – Adjust the play in the throttle cable. ( p. 28)
Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death. – When
running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an effective exhaust extraction system.
– Start the engine and let it run idle. Move the handlebar to and fro over the entire
steering range.
The idle speed must not change.
» If the idle speed changes:
– Check the throttle cable routing.
7.2 Adjusting the play in the throttle cable

– Move the handlebar to the straight-ahead position. – Push back sleeve . – Loosen lock nut . – Adjust the play in the throttle
cable by turning adjusting screw !.
Guideline
Throttle cable play 3... 5 mm (0.12... 0.2 in)
– Tighten lock nut .
B00728-10
– Slide on sleeve .
7.3 Checking the clutch lever play

101914-10
– Check the clutch lever for smooth operation. – Move the handlebar to the straight-ahead position. Lightly pull the clutch lever
and
ascertain the clutch lever play (.
Clutch lever play 1... 3 mm (0.04... 0.12 in)
» If the clutch lever play does not meet specifications:
– Adjust the clutch cable play. ( p. 29)
Note Clutch damage If there is no play on the clutch lever, the clutch will begin to slip. – When operating the motorcycle, always
check the clutch lever play.
– Move the handlebar to and fro over the entire steering range.
The clutch lever play must not change.
» If the clutch lever play changes:
– Check the routing of the clutch cable.

7 HANDLEBAR, CONTROLS
29
7.4 Adjusting the clutch cable play

101915-10
– Move the handlebar to the straight-ahead position. – Push back sleeve . – Loosen lock nut . – Adjust the play in the clutch level
( by turning adjusting screw !.
Guideline
Clutch lever play 1... 3 mm (0.04... 0.12 in)
– Tighten lock nut . – Slide on sleeve .

8 SHOCK ABSORBER, SWINGARM
30
8.1 Adjusting the spring preload of the shock absorber

Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior.
– Following modifications, ride slowly at first to get the feel of the new ride behavior.
Info The spring preload defines the initial situation of the spring process on the shock absorber. The best spring preload setting is
achieved when it is set for the weight of the rider and that of any baggage and a passenger, thus ensuring an ideal compromise
between maneuverability and stability.
– Adjust the spring preload by turning adjusting ring .
Guideline
Spring preload
Standard 3 clicks Full payload 10 clicks
Hook wrench (T106S) ( p. 196)
Info The spring preload can be set to 10 different positions.
8.2 Removing the shock absorber

– Remove fitting . – Lift the link fork and take out the shock absorber ! toward the rear.
8.3 Installing the shock absorber

101886-10
308258-10
308259-10
308259-11
Main work – Remove screw .
Info Protect the link fork and attachments from damage. Ensure that the chain and brake line are not damaged.
Main work – Lift the link fork and position shock absorber . – Mount fitting but do not tighten yet.
Guideline
Fitting, bottom shock absorber M10x1.25 45 Nm
(33.2 lbf ft)

31
– Lift the link fork. – Mount and tighten screw !.
Guideline
Screw, top shock absorber M10x1.25 50 Nm
(36.9 lbf ft)
– Tighten fitting .
Guideline
Fitting, bottom shock absorber M10x1.25 45 Nm
(33.2 lbf ft)
Finishing work – Remove the motorcycle from the work stand. ( p. 11)
8.4 Removing the spring

Condition The shock absorber has been removed.
– Clamp the shock absorber into the special tool.
Spring compressor (T14050S) ( p. 196)
Info Use the ring of the special tool with the smallest possible inside diameter. It must be pressed directly onto the spring.
– Compress the spring. – Remove spring retainer . – Release the spring. Remove the shock absorber from the special tool. –
Remove the spring.
8.5 Installing the spring

308258-11
201698-10
201697-10
201697-10
– Clamp the shock absorber in the vise using soft jaws for protection. – Note the position of the spring preload. – Loosen
adjusting ring ( using the special tool.
– Mount the spring.
The tight coil of the spring is at the bottom. – Clamp the shock absorber into the special tool.
Spring compressor (T14050S) ( p. 196)
Info Use the ring of the special tool with the smallest possible inside diameter. It must be pressed directly onto the spring.
– Mount spring retainer .
The open end is opposite the spring end. – Release the spring. Remove the shock absorber from the special tool. –
Clamp the shock absorber in the vise using soft jaws for protection.

32
201698-10
Alternative 1
– Tension the spring to the prescribed position by turning the adjusting ring.
Guideline
Spring preload
Standard 3 clicks Full payload 10 clicks
Alternative 2
Warning Danger of accidents Modifications to the suspension settings can seriously alter the vehicle's ride behavior. – Extreme
modifications to the adjustment of the suspension components can cause a serious deterioration in the handling characteris- tics
and overload some components. – Only make adjustments within the recommended range. – After making adjustments, ride
slowly at first to get the feel of the
new ride behavior.
– Tension the spring to the position measured during dismantling by turning the
adjusting ring.

9 EXHAUST
33
9.1 Removing the exhaust manifold

Warning Danger of burns The exhaust system gets very hot when the vehicle is driven.
– Allow the exhaust system to cool down. Do not touch hot components.
308293-10
308294-10
308295-10
308296-10
308297-10
– Remove nuts with the washers. – Swing the radiator forward slightly.
– Remove the cable binder, expose the connector of the lambda probe, and
detach.
– Loosen exhaust clamp !.
– Remove the nuts ".
– Remove the exhaust manifold toward the front.

9 EXHAUST
34
9.2 Installing the exhaust manifold

308297-10
308296-11
308295-11
308294-11
308293-11
– Position the exhaust manifold.
– Mount nuts but do not tighten them yet.
Guideline
Nut, exhaust flange M8 22 Nm
(16.2 lbf ft)
– Position and tighten exhaust clamp .
Guideline
Exhaust clamp - 10 Nm (7.4 lbf ft)
– Tighten nuts .
Guideline
Nut, exhaust flange M8 22 Nm
(16.2 lbf ft)
– Plug in connector !. – Secure the connector with a cable binder.
– Position the radiator. – Mount and tighten nuts " with the washers.
Guideline
Nut, radiator M6 5 Nm (3.7 lbf ft)

9 EXHAUST
35
9.3 Removing the main silencer

Preparatory work – Remove the exhaust manifold. ( p. 33)
308299-10
308300-10
308301-10
308302-10
308303-10
Main work – Remove screw with washers.
– Remove screw with the sleeve. – Hang the brake fluid reservoir to the side.
Info Ensure that brake fluid does not escape.
– Remove screw with washers.
– Remove screw ".
Info Do not misplace the sleeves.
– Take off the main silencer toward the bottom.

9 EXHAUST
36
9.4 Installing the main silencer

308303-10
308302-11
308301-11
308300-11
308299-11
Main work – Position the main silencer.
– Mount and tighten screw .
Guideline
Screw, main silencer M8 23 Nm (17 lbf ft)
Info Make sure the sleeves are seated correctly.
– Mount and tighten screw with the washers.
Guideline
Screw, main silencer M6 11 Nm (8.1 lbf ft)
– Position the brake fluid reservoir. – Mount and tighten screw ! with the sleeve.
Guideline
Screw, brake fluid reservoir of rear brake
M6 9 Nm (6.6 lbf ft)
– Mount and tighten screw " with the washers.
Guideline
Screw, main silencer M6 11 Nm (8.1 lbf ft)
Finishing work – Install the exhaust manifold. ( p. 34)

10 AIR FILTER
37
10.1 Removing the air filter

Note Engine failure Unfiltered intake air has a negative effect on the service life of the engine.
– Never ride the vehicle without an air filter since dust and dirt can get into the engine and result in increased wear.
Preparatory work – Remove the passenger seat. ( p. 39) – Remove the seat. ( p. 38)
– Remove air filter . – Clean the air filter box.
10.2 Installing the air filter

308260-10
308261-10
308261-11
308260-11
Main work – Remove screws . – Pull the air filter box lid forward and move to the side.
Main work – Position air filter .
– Mount air filter box lid.
Info Make sure the air filter box lid is seated correctly.
– Mount and tighten screws .
Guideline
Screw, air filter box M6 6 Nm (4.4 lbf ft)
Finishing work – Mount the seat. ( p. 39) – Mount the passenger seat. ( p. 39)

11 FUEL TANK, SEAT, TRIM
38
11.1 Opening the filler cap

Danger Fire hazard Fuel is highly flammable.
– Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately. – The fuel in the fuel tank expands when
warm and may emerge if overfilled. Follow the instructions on refueling.
Warning Danger of poisoning Fuel is poisonous and a health hazard.
– Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with soap and
water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel. Store fuel properly
in a suitable canister and keep away from children.
– Lift the cover of the filler cap and insert the ignition key in the lock.
Note Danger of damage Ignition key breakage. – To take pressure off of the ignition key, push down on the filler cap. Damaged
ignition keys must be replaced.
– Turn the ignition key 90° clockwise. – Open the filler cap. – Remove the ignition key.
11.2 Closing the filler cap

Warning Fire hazard Fuel is highly flammable, poisonous and harmful to your health. – After closing the filler cap, ensure that it
is locked properly. Change
clothing that has been contaminated with fuel. Immediately clean contaminated areas on the skin with soap and water.
– Close the filler cap. – Push down the filler cap until the lock engages.
11.3 Removing the seat

Preparatory work – Remove the passenger seat. ( p. 39)
B00710-10
B00711-01
101891-10
Main work – Remove screws . – Raise the rear of the seat, pull it towards the rear, and remove it upwards.

39
11.4 Mounting the seat

Main work – Attach seat recesses ( at screws and lower at the rear. – Mount and tighten screws .
Guideline
Screw, seat M6 11 Nm (8.1 lbf ft)
Finishing work – Mount the passenger seat. ( p. 39)
11.5 Removing the passenger seat

– Insert the ignition key in seat lock and turn it clockwise. – Raise the rear of the seat, push it towards the rear, and remove it
upwards. – Remove the ignition key from the seat lock.
11.6 Mounting the passenger seat

– Attach hooks on the passenger seat to brackets on the subframe, and lower it
at the rear while pushing forward. – Press down the passenger seat until it clicks into place.
Warning Danger of accidents The passenger seat can come loose from the anchoring if it is not mounted correctly. – After
mounting the passenger seat, check that it is locked correctly by
pulling up.
– Finally, check that the passenger seat is correctly mounted.
11.7 Removing the fuel tank cover

101892-10
101881-10
101890-10

40
304820-10
308273-10
308274-10
308275-10
Create the tool (special screw):
Three conventional screws are required. – Cut off screw to length (.
Guideline
Screw M5x50
Length ( 40 mm (1.57 in)
– Cut a slot into the top end of the screw.
– Remove screw .
Info Always remove the screws individually and replace them with a special screw to avoid distorting the fuel tank.
– Mount and tighten special screw .
– Remove screw . – Mount and tighten another special screw .
– Remove screw . – Mount and tighten another special screw . – Open the filler cap. ( p. 38)

41
308276-10
308277-10
308278-10
308279-10
308280-10
308281-10
– Remove filler cap !.
– Remove screws " with the washers.
– Remove screws #. – Remove screws $.
– Remove cap % from the compensating tank.
– Remove screws &.
– Lift the fuel tank cover. – Detach the side covers on both sides.

42
– Close the fuel tank with a suitable plug.
11.8 Installing the fuel tank cover

308282-10
308283-10
308283-10
308282-11
– Push back hose clamp '. – Pull off the vent hose. – Remove the fuel tank cover.
Main work – Remove the plug.
– Mount the vent hose. – Position hose clamp .

43
308281-10
308280-11
308279-11
308276-11
308284-10
– Position the fuel tank cover. – Attach the side cover on both sides.
Guideline
Remaining screws, chassis M5 5 Nm (3.7 lbf ft)
– Mount plug ! of the compensating tank.
– Mount filler cap ".
– Individually remove special screws # and replace with screws $.
Info Always replace the screws individually, or the fuel tank will become dis- torted and it will no longer be possible to mount
the screws.
– When all screws have been replaced, tighten the screws crosswise.
Guideline
Screw, fuel tank cover M5 4 Nm (3 lbf ft)

44
– Mount and tighten screws &.
Guideline
Screw, fuel tank trim M5 5 Nm (3.7 lbf ft)
– Mount and tighten screws '.
Guideline
Screw, front seat fixing M6 5 Nm (3.7 lbf ft)
Finishing work – Mount the seat. ( p. 39) – Mount the passenger seat. ( p. 39)
11.9 Removing the fuel tank

Preparatory work – Remove the passenger seat. ( p. 39) – Remove the seat. ( p. 38) – Remove the fuel tank cover. ( p. 39)
308285-10
308278-11
308286-10
– Mount and tighten screws % with the washer.
Guideline
Screw, fuel tank M6 11 Nm (8.1 lbf ft)
Main work – Remove screw . – Hang the EFI control unit to one side.
Info Protect the frame and attachments from damage.

45
– Push back hose clamp $. – Pull off the fuel line and remove the fuel tank.
11.10 Installing the fuel tank

308287-10
308288-10
308289-10
308290-10
308291-10
– Remove screws .
– Take off the holder !.
– Detach connector ".
– Detach the fuel line with a suitable tool #.

46
308291-11
308290-11
308289-11
308288-11
308287-11
Main work – Connect the fuel line. – Position hose clamp .
– Remove tool .
– Plug in connector !.
– Position the fuel tank. – Position the holder ".
– Mount and tighten screws #.
Guideline
Screw, fuel tank M6 11 Nm (8.1 lbf ft)

47
– Position the EFI control unit. – Mount and tighten screws $.
Guideline
Screw, EFI control unit M4 4 Nm (3 lbf ft)
Finishing work – Install the fuel tank cover. ( p. 42) – Mount the seat. ( p. 39) – Mount the passenger seat. ( p. 39)
11.11 Removing the front spoiler

– Remove screws . – Take off the front spoiler.
11.12 Fitting front spoiler

308286-11
101895-10
101896-10
101895-10
101896-10
– Remove screws .
– Position the front spoiler. Mount screws but do not tighten yet.
Guideline
– Tighten screw .
Guideline

48
11.13 Dismounting the front fender

– Remove screws . Remove the front fender.
11.14 Installing the front fender

– Position the front fender. Mount and tighten screws .
Guideline
Screw, front fender M6 11 Nm (8.1 lbf ft)
11.15 Checking the fuel pressure

Condition The fuel tank is full. Ensure that the battery voltage does not drop below 12.5 V. The ignition is off. The diagnostics
tool is connected.
308234-10
308234-10
308292-10
– Detach the fuel line with a suitable tool. – Push back hose clamp and pull off the fuel line.

49
03
02
400926-10
– Mount special tool .
Pressure testing tool (61029094000) ( p. 191)
– Mount special tool ! with the nozzle code 0,45.
Testing hose (61029093000) ( p. 191)
– Position the hose end in a fuel can.
Guideline
Minimum size of fuel can 10 l (2.6 US gal)
– Switch the ignition on. – Execute "Actuator test" > "Fuel pump relay function test".
400927-01
– Check the fuel pressure with the filler cap closed.
Fuel pressure
When the fuel pump is active 2.5... 2.9 bar (36... 42 psi)
» If the specification is not reached: – Open the filler cap. ( p. 38) – Check the tank air vent system.
400928-01
– Check the fuel pressure with the filler cap open.
Fuel pressure
When the fuel pump is active 2.5... 2.9 bar (36... 42 psi)
» If the specification is not reached:
– Check that the fuel line is clear. – Change the fuel filter. ( p. 49) – Replace the fuel pump. ( p. 51) – Stop the "Function test of
fuel pump control" actuator test by pressing the "Quit" but-
ton. – Remove the special tools.
– Connect the fuel line and position hose clamp . – Remove the tool.
308292-10
11.16 Changing the fuel filter


50
Preparatory work – Remove the passenger seat. ( p. 39) – Remove the seat. ( p. 38) – Remove the fuel tank cover. ( p. 39) –
Dismount the fuel tank. ( p. 44) – Drain the fuel from the fuel tank into a suitable container.
304887-10
304888-10
304890-10
304887-10
Main work – Take fuel filter out of the holder.
– Remove hose clamp and pull off the fuel hose. – Push back hose clamp ! and remove the fuel filter.
– Position the fuel filter.
Connection ( faces to the left. – Position the fuel hoses and mount hose clamp . – Position hose clamps !.
– Position fuel filter in the holder.
Finishing work – Install the fuel tank. ( p. 45) – Install the fuel tank cover. ( p. 42) – Mount the seat. ( p. 39) – Mount the
passenger seat. ( p. 39)

51
11.17 Replacing the fuel pump

Preparatory work – Remove the passenger seat. ( p. 39) – Remove the seat. ( p. 38) – Remove the fuel tank cover. ( p. 39) –
Dismount the fuel tank. ( p. 44) – Drain the fuel from the fuel tank into a suitable container.
304889-10
304891-10
304889-10
Main work – Remove screws . – Remove the fuel pump with the gasket.
– Position gasket .
– Position the fuel pump with the gasket. – Install the screws and tighten them diagonally.
Guideline
Screw, fuel pump M5 5 Nm (3.7 lbf ft)
Finishing work – Install the fuel tank. ( p. 45) – Install the fuel tank cover. ( p. 42) – Mount the seat. ( p. 39) – Mount the
passenger seat. ( p. 39)

12 WHEELS
52
12.1 Checking the tire air pressure

Info Low tire air pressure leads to abnormal wear and overheating of the tire. Correct tire air pressure ensures optimal riding
comfort and maximum tire service life.
400695-01
– Remove the dust cap. – Check tire air pressure when the tires are cold.
Tire air pressure, solo
Front 2.0 bar (29 psi) Rear 2.0 bar (29 psi)
Tire air pressure with passenger/full payload
Front 2.0 bar (29 psi) Rear 2.2 bar (32 psi)
» If the tire air pressure does not meet specifications:
– Correct the tire air pressure. – Mount the dust cap.
12.2 Checking the tire condition

Warning Danger of accidents Uncontrollable vehicle handling in the event of a flat tire.
– In the interest of safety, replace damaged or worn tires immediately.
Warning Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
– The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.
Warning Danger of accidents Uncontrollable handling characteristic due to non-approved and/or non-recommended tires/wheels.
– Only tires/wheels approved by KTM and with the corresponding speed index should be used.
Info The type, condition and air pressure of the tires all have a major impact on the riding behavior of the motorcycle. Worn tires
have a negative effect on riding behavior, especially on wet surfaces.
400602-10
– Check the front and rear tires for cuts, run-in objects and other damage.
» If the tires exhibit cuts, run-in objects or other damage:
– Change the tires. – Check the depth of the tread.
Info Note local national regulations concerning the minimum tread depth.
Minimum tread depth ≥ 2 mm (≥ 0.08 in)
» If the tread depth is less than the minimum permissible depth:
– Change the tires. – Check the age of the tires.
Info The tire's date of the manufacture is usually part of the tire markings and is indicated by the last four digits of the DOT
marking. The first two digits refer to the week of manufacture and last two digits refer to the year of manufacture. KTM
recommends that the tires are changed regardless of the actual wear, at the latest after 5 years.

12 WHEELS
53
» If a tire is more than 5 years old:
– Change the tires.
12.3 Checking the brake discs

Warning Danger of accidents Reduced braking efficiency due to worn brake disc(s).
– Change the worn brake disc(s) without delay.
– Check the thickness of the front and rear brake discs at several places on the disk
to see if it conforms to measurement (.
Info Wear reduces the thickness of the brake disc in area of the brake disc.
Brake discs - wear limit
Front 3.6 mm (0.142 in) Rear 3.6 mm (0.142 in)
» If the brake disc thickness is less than the specified value:
– Change the brake discs. – Check the front and rear brake discs for damage, cracking, and deformation.
» If the brake disc shows signs of damage, cracking, or deformation:
– Change the brake discs.
12.4 Front wheel

12.4.1 Removing the front wheel
Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) – Raise the motorcycle with the front wheel stand. ( p.
9)
Main work – Remove screws and push the fender to the side. – Remove screw and pull wheel speed sensor ! out of the hole. –
Loosen screws " and screw #. – Unscrew screw # about six turns and press your hand on the screw to push the
wheel spindle out of the axle clamp. Remove screw #.
damaged.
– Holding the front wheel, withdraw the wheel spindle. Take the front wheel out of
the fork.
Info Do not pull the hand brake lever when the front wheel is removed.
B01391-10
12.4.2 Installing the front wheel
Warning Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.
– Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.
400480-10

12 WHEELS
54
– Clean the thread of the wheel spindle and screw . – Position the front wheel and insert the wheel spindle.
The brake linings are correctly positioned. – Mount and tighten screw .
Guideline
Screw, front wheel spindle M8 30 Nm
(22.1 lbf ft)
– Insert wheel speed sensor ! into the hole. Mount and tighten screw ".
Guideline
– Mount and tighten screws #. – Take the motorcycle off of the front wheel stand. ( p. 10) – Pull the front brake and push down
hard on the fork several times to align the fork
legs. – Tighten screws $.
Guideline
Screw, fork stub M8 15 Nm
(11.1 lbf ft)
Finishing work – Take the motorcycle off of the rear wheel stand. ( p. 9)
12.4.3 Removing the brake disc of the front brake
Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) – Raise the motorcycle with the front wheel stand. ( p.
9) – Remove the front wheel. ( p. 53)
Main work – Remove screws . – Take off the ABS sensor wheel and brake disc.
12.4.4 Installing the brake disc of the front brake
B01392-10
B01391-11
307349-10
307349-10
Main work – Check the wheel bearing for damage and wear.
– Change the wheel bearing. – Clean and grease the shaft seal rings and mating surfaces ( of the spacers.
– Insert the spacers.
Main work – Clean the contact surface of the brake disc. – Position the brake disc with the label facing outward. – Position the
ABS sensor wheel. – Mount and tighten screws .
Guideline
Screw, front brake disc M8 30 Nm
(22.1 lbf ft)
Loctite® 243TM

12 WHEELS
55
Finishing work – Install the front wheel. ( p. 53) – Take the motorcycle off of the rear wheel stand. ( p. 9)
12.5 Rear wheel

12.5.1 Removing the rear wheel
Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) Main work – Remove screw and pull wheel speed
sensor out of the hole.
– Remove nut ! and the washer. Remove chain adjuster ". – Holding the rear wheel, withdraw wheel spindle #" with the washer
and chain
adjuster. – Push the rear wheel forward as far as possible and take the chain off the rear
sprocket.
damaged.
– Pull the rear wheel back and take it out of the swingarm.
Info Do not operate the foot brake when the rear wheel is removed.
101900-10
12.5.2 Installing the rear wheel
Warning Danger of accidents No braking effect when operating the rear brake.
– After installing the rear wheel, always operate the foot brake until the pressure point is reached.
Main work – Check the rear hub rubber dampers. ( p. 60)
101901-10
– Check the wheel bearing for damage and wear.
– Change the wheel bearing. – Clean and grease the shaft seal rings and mating surfaces ( of the spacers.
– Clean the thread of the wheel spindle and nut . – Clean the fixing locations on the brake caliper support and swingarm. – Install
the rubber damper and rear sprocket carrier on the rear wheel. – Position the rear wheel.
The brake linings are correctly positioned. – Push the rear wheel as far forward as possible and place the chain on the
rear
sprocket.

12 WHEELS
56
– Pull the rear wheel back and mount wheel spindle ! with the washer and chain
adjuster ".
Info Mount the left and right chain adjusters " in the same position.
– Mount nut and washer. – Push the rear wheel forward so that the chain adjusters are on the screws, and
tighten nut . Guideline
In order for the rear wheel to be correctly aligned, the markings on the left and right chain adjusters must be in the same position
relative to the reference marks ).
Nut, rear wheel spindle M14x1.5 90 Nm
(66.4 lbf ft)
– Insert wheel speed sensor # into the hole. Mount and tighten screw $.
Guideline
Finishing work – Take the motorcycle off of the rear wheel stand. ( p. 9)
12.5.3 Removing the brake disc of the rear brake
Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) – Remove the rear wheel. ( p. 55)
– Remove screws . – Remove the brake disc.
12.5.4 Installing the brake disc of the rear brake
101900-11
307350-10
307351-10
307351-11
Main work – Remove screws . – Take off the ABS sensor wheel.
Main work – Clean the contact surface of the brake disc and the ABS sensor wheel. – Position the brake disc with the label facing
outward. – Mount and tighten screws .
Guideline
Screw, rear brake disc M8 30 Nm
(22.1 lbf ft)
Loctite® 243TM

12 WHEELS
57
Loctite® 243TM
Finishing work – Install the rear wheel. ( p. 55) – Take the motorcycle off of the rear wheel stand. ( p. 9)
12.5.5 Checking the chain tension
Warning Danger of accidents Danger caused by incorrect chain tension.
– If the chain is too taut, the components of the secondary power transmission (chain, engine sprocket, rear sprocket, bear-
ings in the transmission and in the rear wheel) will be under additional load. In addition to premature wear, this can cause the
chain or the countershaft of the transmission to break in extreme cases. If the chain is too loose, however, it may fall off the
engine sprocket or rear sprocket and block the rear wheel or damage the engine. Ensure that the chain tension is correct and
adjust it if necessary.
– Lean the motorcycle on the side stand. – Shift gear to neutral. – In the area of chain sliding guard, press the chain upward
toward the swingarm and
determine chain tension (.
Info The upper chain section ) must be taut. Chain wear is not always even, so you should repeat this measurement at different
chain positions.
Chain tension 5... 7 mm (0.2... 0.28 in)
» If the chain tension does not meet specifications:
– Adjust the chain tension. ( p. 57)
B00731-10
12.5.6 Adjusting the chain tension
Warning Danger of accidents Danger caused by incorrect chain tension.
– If the chain is too taut, the components of the secondary power transmission (chain, engine sprocket, rear sprocket, bear-
ings in the transmission and in the rear wheel) will be under additional load. In addition to premature wear, this can cause the
chain or the countershaft of the transmission to break in extreme cases. If the chain is too loose, however, it may fall off the
engine sprocket or rear sprocket and block the rear wheel or damage the engine. Ensure that the chain tension is correct and
adjust it if necessary.
Preparatory work – Check the chain tension. ( p. 57)
307350-11
– Position the ABS sensor wheel. – Mount and tighten screws .
Guideline
Screw, ABS sensor wheel M6 12 Nm
(8.9 lbf ft)

12 WHEELS
58
Main work – Loosen nut . – Loosen nuts . – Adjust the chain tension by turning adjusting screws ! on the left and right.
Guideline
Chain tension 5... 7 mm (0.2... 0.28 in) Turn adjusting screws ! on the left and right so that the markings on the left and right
chain adjuster " are in the same position in relation to reference marks *. The rear wheel is then correctly aligned.
Info The upper chain section must be taut. Chain wear is not always even, so you should check the setting at different chain
positions.
– Tighten nuts . – Make sure that chain adjusters " are fitted correctly on adjusting screws !. – Tighten nut .
Guideline
(66.4 lbf ft)
12.5.7 Checking the chain, rear sprocket, and engine sprocket
100132-10
– Check the rear sprocket and engine sprocket for wear. » If the rear sprocket and engine sprocket are worn:
– Change the power set.
Info The engine sprocket, rear sprocket, and chain should always be replaced together.
0A
0B
1 2 3 18 19 20
401288-10
101893-10
– Shift gear to neutral. – Pull the lower chain section with specified weight (.
Guideline
Weight, chain wear measurement 15 kg (33 lb.)
– Measure the distance ) of 20 chain links in the lower chain section.
Info Chain wear is not always even, so you should repeat this measurement at different chain positions.
Maximum distance ) at the longest chain section
301.6 mm (11.874 in)
» If the distance ) is greater than the specified measurement:
– Change the power set.
Info When the chain is replaced, the rear sprocket and engine sprocket should also be changed. New chains wear out faster on
old, worn sprockets.

12 WHEELS
59
– Position the chain guard and tighten screw .
Guideline
Screw, chain guard EJOT PT® 4 Nm (3 lbf ft)
– Tighten screw .
Guideline
Screw, chain guard EJOT PT® 4 Nm (3 lbf ft)
– Tighten screw !.
Guideline
12.5.8 Cleaning the chain
Warning Danger of accidents Oil or grease on the tires reduces their grip.
– Remove oil and grease with a suitable cleaning material.
B01416-10
B01416-10
C00199-10
– Remove screws and ! and release screw . Push the chain guard aside.
– Check the chain sliding guard for wear.
» If drill hole + becomes visible on the chain sliding guard in area *:
– Change the chain sliding guard. – Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:
– Tighten the chain sliding guard.

12 WHEELS
60
Warning Environmental hazard Hazardous substances cause environmental damage.
– Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.
Info The service life of the chain depends largely on its maintenance.
– Clean the chain regularly. – Rinse off loose dirt with a soft jet of water. – Remove old grease remains with chain cleaner.
Chain cleaner ( p. 187)
– After drying, apply chain spray.
Chain lube for road use ( p. 187)
12.5.9 Checking the rear hub rubber dampers
Info The engine power is transmitted from the rear sprocket to the rear wheel via 6 rubber dampers. They eventually wear out
during operation. If the rubber dampers are not changed in time, the rear sprocket carrier and the rear hub will be damaged.
Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) – Remove the rear wheel. ( p. 55)
400725-01
101925-10
101926-10
Main work – Check bearing .
» If the bearing is damaged or worn:
– Change the bearing. – Check the rubber dampers of the rear hub for damage and wear. » If the rubber dampers of the
rear hub are damaged or worn:
– Change all rubber dampers in the rear hub.
– Lay the read wheel on a workbench with the rear sprocket facing upwards and
insert the wheel spindle in the hub. – To check the play (, hold the rear wheel tight and try to rotate the rear sprocket.
Info Measure the play on the outside of the rear sprocket.
Play in rubber dampers, rear wheel ≤ 5 mm (≤ 0.2 in)
» If play ( is larger than the specified value:
– Change all rubber dampers in the rear hub. Finishing work – Install the rear wheel. ( p. 55) – Take the motorcycle off
of the rear wheel stand. ( p. 9)

13 WIRING HARNESS, BATTERY
61
13.1 Removing the battery

Warning Risk of injury Battery acid and battery gases cause serious chemical burns.
– Keep batteries out of the reach of children. – Wear suitable protective clothing and goggles. – Avoid contact with battery acid
and battery gases. – Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms. – In the event of
skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least
15 minutes and contact a physician.
– Pull back the positive terminal cover !. – Disconnect the positive cable " of the battery. – Detach rubber band #. – Pull the
battery up and out of the battery holder.
Info Never operate the motorcycle with a discharged battery or without a battery. In both cases, electrical components and safety
devices can be damaged. The vehicle is therefore no longer roadworthy.
13.2 Installing the battery

101903-10
101904-10
101904-11
101903-11
Main work – Pull back the negative terminal cover . – Disconnect the negative cable of the battery.
Main work – Position the battery in the battery holder.
Info The battery terminals must be at the top.
– Attach rubber band . – Reconnect the positive cable of the battery. – Position positive terminal cover !.
– Connect the negative cable " of the battery. – Position the negative terminal cover #.
Finishing work – Mount the seat. ( p. 39) – Mount the passenger seat. ( p. 39) – Set the clock. ( p. 76)

62
13.3 Disconnecting the negative cable of the battery

Main work – Pull back the negative terminal cover . – Disconnect the negative cable of the battery.
13.4 Reconnecting the negative cable of the battery

Main work – Connect the negative cable of the battery. – Position the negative terminal cover .
13.5 Recharging the battery

Warning Risk of injury Battery acid and battery gases cause serious chemical burns.
– Keep batteries out of the reach of children. – Wear suitable protective clothing and goggles. – Avoid contact with battery acid
and battery gases. – Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms. – In the event of
skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least
15 minutes and contact a physician.
Warning Environmental hazard The battery contains elements that are harmful to the environment.
– Do not discard batteries with the household waste. Dispose of faulty batteries in an environmentally compatible manner.
Give the battery to your authorized KTM dealer or dispose of it at a collection point for used batteries.
Info Even when there is no load on the battery, it still loses power steadily. The charge state and the type of charge are very
important for the service life of the battery. Rapid recharging with a high charging current shortens the battery's service life. If the
charging current, charging voltage, and charging time are exceeded, electrolyte escapes through the safety valves. This reduces
the battery capacity. If the battery is depleted from starting the vehicle repeatedly, the battery must be charged immediately. If the
battery is left in a discharged state for an extended period, it will become over-discharged and sulfate, destroying the battery. The
battery is maintenance-free, which means that the acid level does not need to be checked.
101903-10
101903-10

63
Preparatory work – Switch off all power consumers and switch off the engine. – Remove the passenger seat. ( p. 39) – Remove
the seat. ( p. 38) – Disconnect the negative cable of the battery to avoid damage to the motorcycle's
electronics.
Main work – Connect the battery charger to the battery. Switch on the battery charger.
Battery charger (58429074000)
You can also use the battery charger to test rest potential and start potential of the battery, and to test the alternator. With this
device, you cannot overcharge the battery.
Info Never remove lid . Charge the battery with a maximum of 10% of the capacity specified on battery housing .
– Switch off the charger after charging. Disconnect the battery.
Guideline
The charge current, charge voltage and charge time must not be exceeded. Charge the battery regularly when the motorcycle is
not in use
3 months
B01395-10
13.6 Checking the charging voltage

Condition The battery must be fully functional and completely charged. Preparatory work – Remove the passenger seat. ( p. 39) –
Remove the seat. ( p. 38) Main work – Start the motorcycle to make checks. ( p. 13)
304934-10
–
Measure the voltage between the specified points. Measuring point Plus (+) – Measuring point Ground (−)
Charging voltage
5,000 rpm 13.5... 15.0 V
» If the displayed value is less than the specified value:
– Check the cable from the alternator to the voltage regulator. – Check the cable from the voltage regulator to the wiring harness.
– Check the stator winding of the alternator. ( p. 156) » If the displayed value is greater than the specified value:
– Change the voltage regulator.

64
13.7 Changing the fuses of individual power consumers

Info The fuse box with the main fuse and the fuses of the individual power consumers is located under the passenger seat.
Preparatory work – Switch off all power consumers and switch off the engine. – Remove the passenger seat. ( p. 39)
B01410-01
Main work – Open fuse box cover. – Remove the defective fuse.
Guideline
Fuse 1 - 30 A - main fuse Fuse 2 - 15 A - start auxiliary relay, alarm system (OPTIONAL) Fuse 3 - 15 A - control unit, power
relay Fuse 4 - 15 A - ignition coil Fuse 5 - 15 A - radiator fan Fuse 6 - 15 A - horn, brake light, turn signal, high beam, low beam,
parking light, tail light, license plate lamp Fuse 7 - 10 A - ABS control unit Fuse 8 - 10 A - combination instrument, control unit
Fuse 9 - 10 A - auxiliary equipment
Info A defective fuse is indicated by a burned-out fuse wire (.
Warning Fire hazard The electrical system can be overloaded if the wrong fuses are used. – Use only fuses with the prescribed
amperage. Never by-pass or repair
fuses.
– Use spare fuses with the correct rating only.
Fuse (75011088010) ( p. 160) Fuse (75011088015) ( p. 160) Fuse (75011088030) ( p. 160)
Tip Replace the spare fuse in the fuse box so that it is available if needed.
– Check that the power consumer is functioning properly. – Close the fuse box cover. Finishing work – Mount the passenger seat.
( p. 39)

14 BRAKE SYSTEM
65
14.1 Checking the front brake linings

Warning Danger of accidents Reduced braking efficiency caused by worn brake linings.
– Change worn brake linings immediately.
Note Danger of accidents Reduced braking efficiency caused by damaged brake discs.
– If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are destroyed. Check the brake linings regularly.
– Check the brake linings for minimum thickness (.
Minimum thickness ( ≥ 1 mm (≥ 0.04 in)
» If the minimum thickness is less than specified:
– Change the front brake linings. ( p. 65) – Check the brake linings for damage and cracking.
» If there is wear or tearing:
– Change the front brake linings. ( p. 65)
B00739-10
14.2 Changing the front brake linings

Warning Skin irritation Brake fluid can cause skin irritation on contact.
– Avoid contact with skin and eyes, and keep out of the reach of children. – Wear suitable protective clothing and goggles. – If
brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.
Warning Danger of accidents Reduced braking efficiency due to old brake fluid.
– Change the brake fluid of the front and rear brake according to the service schedule.
Warning Danger of accidents Reduced braking efficiency due to use of non-approved brake linings.
– Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construc-
tion and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM brake
linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the original license.
The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.
Info Avoid contact between brake fluid and painted parts. Brake fluid attacks paint! Use only clean brake fluid from a sealed
container.

14 BRAKE SYSTEM
66
307304-10
307305-10
307306-10
307307-10
307308-10
307307-10
– Move the brake fluid reservoir mounted on the handlebar to a horizontal position. – Remove screws . – Remove cover with
membrane !.
– Remove locking clip ".
– Remove pin #. – Take off springs $.
– Remove brake linings %. – Clean the brake caliper.
– Press the brake piston back to its basic position and make sure that no brake fluid
overflows from the brake fluid reservoir. Suction it off if necessary.
Info Protect the components against damage.
– Position brake linings %.
Info Always change the brake linings in pairs.

14 BRAKE SYSTEM
67
– Correct the brake fluid level to level (.
Guideline
Level ( 5 mm (0.2 in)
Brake fluid DOT 4 / DOT 5.1 ( p. 186)
– Position the cover with the membrane. Mount and tighten the screws.
Info Clean up overflowed or spilt brake fluid immediately with water.
14.3 Checking the brake fluid level of the front brake

Warning Danger of accidents Failure of the brake system.
– If the brake fluid level falls below the MIN mark, this indicates a leakage in the brake system or worn-out brake linings.
Check the brake system and do not continue riding.
– Move the brake fluid reservoir mounted on the handlebar to a horizontal position. – Check the brake fluid level in viewer .
» If the brake fluid is below the MIN marking:
– Add front brake fluid. ( p. 67)
14.4 Adding front brake fluid

307306-10
307303-10
C00200-10
– Position springs $.
The arrow on the spring points in the direction of travel. – Mount pin #.
Info Make sure the springs are seated correctly.
– Activate the hand brake lever until there is a firm pressure point.

14 BRAKE SYSTEM
68
container.
– Move the brake fluid reservoir mounted on the handlebar to a horizontal position. – Remove screws . – Remove cover with
membrane !. – Add brake fluid to level (.
Guideline
C00201-10
14.5 Changing the front brake fluid

container.
201524-10
201525-10
– Move the brake fluid reservoir mounted on the handlebar to a horizontal position. – Cover painted parts. – Remove screws . –
Remove cover with the membrane. – Draw the old brake fluid out of the brake fluid reservoir using a syringe and fill with
fresh brake fluid.
Bleed syringe (50329050000) ( p. 189) Brake fluid DOT 4 / DOT 5.1 ( p. 186)
– Mount the corresponding bleeder cover ! from the special tool set.
Bleeder cover (00029013000) ( p. 189)
– Connect the bleeding device.
Bleeding device (00029013100) ( p. 189)

14 BRAKE SYSTEM
69
– Correct the brake fluid level to level (.
Guideline
– Check the hand brake lever for a firm pressure point.
14.6 Checking the rear brake linings

Warning Danger of accidents Reduced braking efficiency caused by worn brake linings.
– Change worn brake linings immediately.
Note Danger of accidents Reduced braking efficiency caused by damaged brake discs.
– If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are destroyed. Check the brake linings regularly.
B01390-10
201494-10
307302-10
307303-10
– Open shut-off valve ".
Info Follow the operating instructions of the bleeding device.
– Ensure that the filling pressure is set on pressure gauge (. Correct the filling pres-
sure on pressure regulator ) if necessary. Guideline
Filling pressure 2... 2.5 bar (29... 36 psi)
– Pull off dust cap # of the bleeder screw of the brake caliper. Connect the bleeder
bottle hose.
– Open bleeder screw $ by approximately one half turn.
Info Drain until fresh brake fluid emerges in the bleeder bottle hose without bubbles.
– Tighten the bleeder screw. – Close shut-off valve ". – Open the bleeder screw again until no more brake fluid emerges.
Info Overfilling of the brake fluid reservoir is prevented.
– Tighten the bleeder screw. Remove the bleeder bottle hose. Attach the dust cap. – Disconnect the bleeding device. Remove the
bleeder cover.
– Check the brake linings for minimum thickness (.
Minimum thickness ( ≥ 1 mm (≥ 0.04 in)
» If the minimum thickness is less than specified: – Change the rear brake linings. ( p. 70) – Check the brake linings for damage
and cracking.
» If there is wear or tearing:
– Change the rear brake linings. ( p. 70)

14 BRAKE SYSTEM
70
14.7 Changing the rear brake linings

Warning Danger of accidents Reduced braking efficiency due to use of non-approved brake linings.
– Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construc-
tion and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM brake
linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the original license.
The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.
container.
308262-10
308263-10
308264-10
– Stand the vehicle upright. – Remove screw cap and membrane . – Push the brake caliper toward the brake disc with your hand
to push back the brake piston; ensure that brake fluid does not runs out of the brake fluid reservoir, removing it if it does.
– Remove locking clips !. – Remove pin ".
– Remove brake linings #. – Clean the brake caliper.

14 BRAKE SYSTEM
71
– Operate the foot brake lever repeatedly until the brake linings are in contact with
the brake disc and there is a pressure point. – Add brake fluid to the MAX marking.
– Mount the screw cap with the washer and membrane.
14.8 Checking the free travel of foot brake lever

Warning Danger of accidents Brake system failure.
– If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to
overheating. Adjust the free travel on foot brake lever according to specifications.
308265-10
308263-11
308262-11
101897-10
– Position brake linings #. – Mount pin ".
– Mount locking clips !.
– Disconnect spring . – Move the foot brake lever back and forth between the end stop and the contact to
the foot brake cylinder piston and check free travel (. Guideline
Free travel at foot brake lever 3... 5 mm (0.12... 0.2 in)
» If the free travel does not meet specifications:
– Adjust the free travel of the foot brake lever. ( p. 72) – Reconnect spring .

14 BRAKE SYSTEM
72
14.9 Adjusting the free travel of the foot brake lever

Warning Danger of accidents Brake system failure.
– If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to
overheating. Adjust the free travel on foot brake lever according to specifications.
– Disconnect spring . – Release nut and use screw ! to adjust the specified free travel (.
Guideline
Free travel at foot brake lever 3... 5 mm (0.12... 0.2 in)
Info The range of adjustment is limited.
– Hold screw ! and tighten nut . – Attach spring .
101897-11
14.10 Checking the rear brake fluid level

101898-10
– Stand the vehicle upright. – Check the brake fluid level in the brake fluid reservoir.
» If the fluid level reaches the MIN marking :
– Add rear brake fluid. ( p. 73)

14 BRAKE SYSTEM
73
14.11 Adding rear brake fluid

container.
– Stand the vehicle upright. – Remove screw cap with membrane . – Add brake fluid to level (.
– Refit screw cap with membrane.
Info Clean up overflowed or spilt brake fluid immediately with water. 101899-10
14.12 Changing the rear brake fluid

container.

14 BRAKE SYSTEM
74
308266-10
308267-10
201494-11
308268-10
308269-10
– Cover painted parts. – Remove screw cap with membrane. – Draw the old brake fluid out of the brake fluid reservoir using a
syringe and fill with
fresh brake fluid.
Bleed syringe (50329050000) ( p. 189) Brake fluid DOT 4 / DOT 5.1 ( p. 186)
– Mount the corresponding bleeder cover from the special tool set.
Bleeder cover (00029013000) ( p. 189)
– Connect the bleeding device.
– Open shut-off valve !.
Info Follow the operating instructions of the bleeding device.
– Ensure that the filling pressure is set on pressure gauge (. Correct the filling pres-
sure on pressure regulator ) if necessary. Guideline
Filling pressure 2... 2.5 bar (29... 36 psi)
– Pull off dust cap " of the bleeder screw. Connect the bleeder bottle hose.
– Open bleeder screw # by approximately one half turn.
Info Drain until fresh brake fluid emerges in the bleeder bottle hose without bubbles.
– Tighten the bleeder screw. – Close shut-off valve !. – Open the bleeder screw again until no more brake fluid emerges.
Info Overfilling of the brake fluid reservoir is prevented.
– Tighten the bleeder screw. Remove the bleeder bottle hose. Attach the dust cap. – Disconnect the bleeding device. Remove the
bleeder cover.
– Stand the vehicle upright. – Correct the brake fluid to level (.
– Refit screw cap with membrane.
– Check the foot brake lever for a firm pressure point.

15 LIGHTING SYSTEM, INSTRUMENTS
75
15.1 Setting kilometers or miles

Info Make the country-specific setting.
Condition The ignition is on. The motorcycle is stationary.
– Press the MODE button briefly and repeatedly until ODO appears on the display. – Press the MODE button for 5 - 10 seconds.
The display changes from km/h to mph or from mph to km/h.
15.2 Adjusting the shift speed RPM 1

– Press the MODE button briefly and repeatedly until TRIP 2 appears on the display. – Press the MODE button for 5 - 10
seconds.
The display RPM 1 appears.
Info The engine speed can be set at intervals of 50. RPM 1 is the engine speed above which the shift warning light starts to flash.
– Set the speed with the MODE and SET buttons.
Info The MODE button increases the value. The SET button decreases the value.
– Do not activate the two buttons for approx. 15 seconds.
The display RPM 1 goes out and the set speed is stored.
15.3 Adjusting the shift speed RPM 2

401303-01
401307-01
401308-01
– Press the MODE button briefly and repeatedly until TRIP 2 appears on the display. – Press the SET button for 5 - 10 seconds.
The display RPM 2 appears.
Info The engine speed can be set at intervals of 50. RPM 2 is the engine speed above which the shift warning light lights up con-
stantly. The speed RPM 2 must always be higher than the speed RPM 1.
– Set the speed with the MODE and SET buttons.
Info The MODE button increases the value. The SET button decreases the value.

76
– Do not activate the two buttons for approx. 15 seconds.
The display RPM 2 goes out and the set speed is stored.
15.4 Setting the time

– Press the MODE button briefly and repeatedly until ODO appears on the display. – Press the MODE and SET buttons for 5 - 10
seconds.
The time display begins to flash. – Set the hours display using the MODE button. – Set the minutes display using the
SET button. – Press the MODE and SET buttons for 5 - 10 seconds.
The time is set.
15.5 Resetting the service interval display

Condition The ignition is on. The engine is switched off. The motorcycle is stationary.
– Press the SET button for more than 10 seconds.
Info The service interval display can only be reset. It is not possible to individually adjust the distance or time to the next
required service.
15.6 Checking the headlight setting
0A
0B
400726-10
– Position the vehicle upright on a horizontal surface in front of a light wall and make
a mark at the height of the center of the low beam headlight. – Make another mark at a distance ) under the first mark.
Guideline
Distance ) 5 cm (2 in)
– Position the vehicle vertically at a distance ( in front of the wall and switch on the
low beam. Guideline
Distance ( 5 m (16 ft)
– The rider, with luggage and passenger if applicable, now mounts the motorcycle. – Check the headlight setting.
The light-dark boundary must lie exactly on the lower mark when the motorcycle is ready to operate with the rider mounted
along with any luggage and a passenger if applicable.
» If the boundary between light and dark does not meet specifications:
– Adjust the headlight range. ( p. 77)
401303-01
401358-01

77
15.7 Adjusting the headlight range

B00764-10
101907-10
101908-10
101908-10
101907-10
– Adjust the beam distance of the headlight by turning screw !.
Guideline
For a motorcycle with rider, and with luggage and a passenger if applicable, the light/dark boundary must be exactly on the lower
mark (applied in: Checking headlight adjustment).
Info Turn clockwise to increase the headlight range; turn counterclockwise to reduce the headlight range.
– Fold the headlight mask up. – Mount and tighten screws .
Guideline
– Mount expanding rivets on both sides.
Finishing work – Check the headlight setting. ( p. 76)

78
15.8 Changing the parking light bulb

Note Damage to reflector Reduced brightness.
– Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease
before mounting.
Preparatory work – Switch off all power consumers and switch off the engine.
B00762-10
B00763-10
101907-10
308243-10
– Remove screws !. – Take off cover ".
– Pull the socket with bulb # out of the housing. – Remove the bulb. – Position a new light bulb in the socket.
Parking light (W5W/socket W2.1x9.5d) ( p. 160)
– Position the socket with bulb # in the housing.

79
– Mount expanding rivets on both sides. – Check that the lighting is functioning properly.
15.9 Changing the headlight bulb

Note Damage to reflector Reduced brightness.
– Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease
before mounting.
Preparatory work – Switch off all power consumers and switch off the engine.
B00762-10
308243-10
101907-10
101907-10
101908-10
– Position cover ". – Mount and tighten screws !.
Guideline

80
B00760-10
B00761-10
B00760-10
101908-10
101907-10
– Take off protection cap !. – Disconnect plug-in connector ".
– Detach retaining clamp #. – Remove headlight bulb $. – Position the new headlight bulb in the headlight housing.
Headlight (H4/socket P43t) ( p. 160)
Info Insert the headlight bulb so that the catches latch into the recesses.
– Attach retaining clamp #.
– Connect plug-in connection ". – Mount protection cap !.
Guideline
– Mount expanding rivets on both sides. – Check that the lighting is functioning properly.

16 ENGINE
81
16.1 Removing the engine

Preparatory work – Raise the motorcycle with the rear wheel stand. ( p. 9) – Remove the front spoiler. ( p. 47) – Remove the
passenger seat. ( p. 39) – Remove the seat. ( p. 38) – Disconnect the negative cable of the battery. ( p. 62) – Drain the coolant. ( p.
148) – Remove the exhaust manifold. ( p. 33)
308304-10
308305-10
308306-10
308307-10
308308-10
Main work – Push back the rubber cap. – Remove nut with washers. – Hang the cable to one side.
– Bend up the lock washer . – Detach the clutch cable.
– Remove nut !. – Detach the clutch cable.
– Disconnect connector ".
– Push back hose clamp #. – Pull off the vent hose.

16 ENGINE
82
308309-10
308310-10
308311-10
308312-10
308313-10
308314-10
– Detach spark plug connector $.
– Remove screws %. – Remove screw &. – Take off the engine sprocket cover.
– Remove screws ' and take off the lock washer.
– Remove nut 02 with washer. – Take off chain adjuster 03. – Push the rear wheel into the foremost position.
– Pull the engine sprocket off of the countershaft and remove it.
– Remove screw 04. – Pull off the shift linkage and hang it to one side.

16 ENGINE
83
308315-10
308316-10
308317-10
308318-10
308319-10
308320-10
– Push back the rubber cap. – Remove nut 05 with washer.
– Expose the cable and unplug connectors 06 and 07.
– Expose the cable and unplug connector 08.
– Release hose clip 09. – Push the throttle valve body upward out of the intake flange.
– Remove screws 0:. – Remove fitting 0;. – Remove both engine fixing arms.
– Push back hose clamps 12 and 13. – Pull off the radiator hoses.

16 ENGINE
84
308321-10
308322-10
308323-10
308324-10
308325-10
– Push back hose clamp 14. – Pull off the radiator hose.
– Remove screws 15. – Pull off the radiator pipe and hang it to one side.
– Remove screws 16. – Take off the retaining bracket.
– Position the floor jack under the engine and fix it using the special tool.
Floor jack attachment (75029055000) ( p. 192)
– Remove fitting 17. – Remove fitting 18. – Remove the cable binder. – Hang ground wire 19 to the side.

16 ENGINE
85
– Lower the engine.
Info You should have an assistant for this step. Make sure that the engine is sufficiently secured against falling over. Protect the
frame and attachments from damage.
308326-10
16.2 Installing the engine

Preparatory work – Lift the motor onto the special tool and secure it.
308326-10
308325-11
308324-10
Main work – Position the engine in the frame.
Info It is useful to draw on the help of an assistant. Protect the frame and attachments against damage.
– Position ground wire and secure it with a cable binder. – Mount fitting but do not tighten yet.
Guideline
Fitting, engine mounting bracket M10 55 Nm
(40.6 lbf ft)
– Mount fitting ! but do not tighten yet.
Guideline
(40.6 lbf ft)
– Remove the floor jack with the special tool.

16 ENGINE
86
308323-11
308322-11
308321-11
308320-11
308327-10
308319-11
– Position the retaining bracket. – Mount and tighten screws ".
Guideline
– Mount the radiator pipe with the O-ring. – Mount and tighten screws #.
Guideline
– Mount the radiator hose. – Position hose clamp $.
– Mount the radiator hoses. – Position hose clamps % and &.
– Tighten fittings and !.
Guideline
(40.6 lbf ft)
– Position both engine fixing arms. – Mount and tighten screws '.
Guideline
Screw, engine bearer on frame M8 30 Nm
(22.1 lbf ft)
– Mount and tighten fitting 02.
Guideline
(40.6 lbf ft)

16 ENGINE
87
308318-11
308317-11
308316-11
308315-11
308314-11
308313-10
– Position the throttle valve body in the intake flange. – Tighten hose clip 03.
– Plug in connector 04. – Position the cable and secure with cable binders.
– Plug in connectors 05 and 06. – Position the cable and secure with cable binders.
– Mount and tighten nut 07 with the washer.
Guideline
Remaining nuts, chassis M5 3 Nm (2.2 lbf ft)
– Position the rubber cap.
– Position the shift linkage. – Mount and tighten screw 08.
Guideline
Screw, shift activation M6 11 Nm
(8.1 lbf ft)
– Position the engine sprocket in the chain and slide onto the countershaft.
Loctite® 243TM

16 ENGINE
88
308312-11
308311-11
308310-11
308309-11
308308-11
308307-11
– Pull the rear wheel toward the rear. – Mount chain adjuster 09. – Mount and tighten nut 0: with the washer.
Guideline
For the rear wheel to be aligned correctly, the markings on the left and right of the chain adjuster must be in the same position as
the reference marks.
(66.4 lbf ft)
– Mount the lock washer and turn it slightly.
The lock washer engages in the gear teeth of the countershaft. – Mount and tighten screws 0;.
Guideline
Remaining nuts, chassis M6 15 Nm
(11.1 lbf ft)
– Position the engine sprocket cover. – Mount and tighten screws 12.
Guideline
(11.1 lbf ft)
– Mount and tighten screw 13.
Guideline
(11.1 lbf ft)
– Mount the spark plug connector 14.
– Mount the vent hose. – Position hose clamp 15.
– Plug in connector 16.

16 ENGINE
89
308306-11
308305-11
308304-11
308328-10
– Attach the outer clutch cable. – Mount and tighten nut 17.
– Attach the inner clutch cable. – Secure the inner clutch cable with lock washer 18.
– Mount and tighten nut 19 with the washers.
Guideline
(11.1 lbf ft)
– Position the rubber cap. – Position the cable and secure with cable binders.
– Remove the oil filler plug 1: with the O-ring from the clutch cover and fill up with
engine oil.
Engine oil 1.6 l (1.7 qt.) Engine oil (SAE 15W/50) ( p. 186)
– Mount and tighten the oil filler plug with the O-ring.
Finishing work – Install the exhaust manifold. ( p. 34) – Reconnect the negative cable of the battery. ( p. 62) – Set the clock. ( p.
76) – Mount the seat. ( p. 39) – Mount the passenger seat. ( p. 39) – Take the motorcycle off of the rear wheel stand. ( p. 9) –
Fill/bleed the cooling system. ( p. 148) – Fit the front spoiler. ( p. 47) – Take a short test ride. – Read out the fault memory using
the KTM diagnostics tool. – Check the engine for leak tightness. – Check the engine oil level. ( p. 152) – Check the coolant level.
( p. 150)

16 ENGINE
90
16.3 Disassembling the engine

16.3.1 Preparations
– Mount special tools and on the engine assembly stand.
Engine fixing arm (90129002060) ( p. 194) Engine fixing arm (90129002050) ( p. 193) Engine assembly stand (61229001000) (
p. 192)
– Mount the engine on special tool.
Info Have an assistant help you or use a crane.
16.3.2 Draining the engine oil
– Remove screw plug ! with the O-ring and oil screen.
16.3.3 Removing the chain securing guide
307956-10
307957-10
307958-10
307959-10
307960-10
– Remove oil drain plug with the O-ring.
– Remove oil screen with the O-ring. – Completely drain the engine oil.
– Remove screws . – Take off the chain securing guide.

16 ENGINE
91
16.3.4 Removing the valve cover
– Remove the spark plug shaft insert !.
16.3.5 Removing the spark plug
– Remove the spark plug using special tool .
Spark plug wrench (77229172000) ( p. 193)
16.3.6 Removing the clutch cover
307961-10
307962-10
307963-10
307966-10
307972-10
– Remove screws with the gasket. – Take off the valve cover with the valve cover seal.
– Take off gasket .
– Remove screws .

16 ENGINE
92
– Remove dowels . – Take off clutch cover gasket !.
16.3.7 Setting the engine to ignition top dead center
307973-10
307974-10
307967-10
307968-10
307969-10
– Take off the clutch cover.
Info Pull the clutch lever forward slightly.
– Remove screw plug .
– Remove screw plug .
– Turn the crankshaft counterclockwise until markings ( align with the edge of the
cylinder head.
Markings ) and * align.

16 ENGINE
93
– Mount special tool ".
Engine blocking screw (61229015000) ( p. 192)
16.3.8 Removing the timing chain tensioner
– Turn the timing chain tensioner screw clockwise.
The timing chain tensioner is locked. – Remove screw . – Remove the timing chain tensioner with the gasket.
16.3.9 Removing the camshaft
307975-10
307976-10
307978-10
307979-10
307981-10
– Remove screw !.
– Remove screw with the O-ring.
– Release screws from the outside to the inside and remove them. – Remove the camshaft bearing bridge. – Remove dowels.

16 ENGINE
94
– Remove exhaust camshaft !.
16.3.10 Removing the cylinder head
307982-10
307983-10
307985-10
307986-10
307987-10
307988-10
– Remove intake camshaft .
– Remove screws .
– Release screws in a crisscross pattern and remove them with the washers. – Take off the cylinder head.
– Take off the cylinder head gasket !. – Remove dowels ".
– Remove timing chain guide rail #.

16 ENGINE
95
16.3.11 Removing the piston
– Take off cylinder base gasket . – Remove dowels !.
16.3.12 Removing the starter motor
– Remove screws . – Take off the starter motor.
16.3.13 Removing the timing chain
307990-10
307991-10
307997-10
307998-10
307999-10
– Push the cylinder upward.
Info Push the cylinder upward only far enough to allow removal of the piston pin.
– Remove piston pin retainer . – Remove the piston pin. – Take off the cylinder with the piston. – Push the piston upward out of
the cylinder.
Info If no other work is required on the cylinder and the piston, you can leave the piston in the cylinder.
– Feed out timing chain .
Info If the timing chain is to be reused, mark the direction of travel.
– Remove screw . – Take off the timing chain tensioning rail toward the top.

16 ENGINE
96
16.3.14 Removing the water pump wheel
– Remove nut ! with washer. – Take off the water pump impeller ".
16.3.15 Removing the alternator cover
308000-10
308001-10
308002-10
308003-10
308004-10
– Remove screws . – Remove the water pump cover with the gasket.
– Remove locating pins .
– Remove screws . – Take off the alternator cover.
– Remove dowels . – Take off alternator cover gasket !.

16 ENGINE
97
16.3.16 Removing the rotor
– Mount special tool in the crankshaft.
Pressure screw for crankshaft (90129020000) ( p. 194)
– Mount special tool ! on the rotor.
Info Left-handed thread!
– Hold it tight using the special tool and pull off the rotor by turning the screw in.
Puller for rotor (90229009000) ( p. 196)
– Remove the spring washer.
16.3.17 Removing the starter drive
308005-10
308066-10
308007-10
308008-10
308009-10
– Remove screw with the washer.
– Take off torque limiter . – Remove starter idler gear .
– Remove screw !. – Remove the retaining bracket.
– Remove freewheel gear ".

16 ENGINE
98
16.3.18 Removing the balancer shaft drive wheel
– Remove nut ! with washers.
– Take off drive wheel of the balancer shaft. – Remove the spring washer.
16.3.19 Removing the gear position sensor
308010-10
308011-10
308012-10
308014-10
308015-10
– Remove screw with the washer.
– Remove balancer shaft gear with a wedge.
– Remove screws . – Take off the retaining bracket. – Remove screws . – Pull off the ignition pulse generator.
– Remove screws !. – Take off the gear position sensor and ignition pulse generator with the cable.

16 ENGINE
99
– Remove contact pin ! and the contact spring.
308016-10
16.3.20 Removing the suction pump
308017-10
308018-10
308019-10
308020-10
– Remove screws . – Take off the oil pump housing of the suction pump.
– Remove dowels .
– Remove external rotor ! and internal rotor ".
– Take off pin #.

16 ENGINE
100
16.3.21 Removing the spacer
– Remove the spacer of the countershaft.
308022-10
16.3.22 Removing the clutch cage
308023-10
308024-10
308025-10
308026-10
– Loosen screws in a crisscross pattern and remove together with the washers and
the clutch springs. – Take off pressure cap .
– Remove pull rod !. – Remove clutch discs ".
– Take off support ring and pretension ring #.
– Hold the clutch basket using the special tool.
Clutch holder (51129003000) ( p. 189)
– Remove nut $ with washer.
Info Left-handed thread!

16 ENGINE
101
– Remove collar sleeve 02.
16.3.23 Removing the primary gear
308027-10
308028-10
308030-10
308031-10
308032-10
308033-10
– Take off inner clutch hub % and washer &.
Info The washer usually sticks to the inner clutch hub.
– Take off clutch basket '.
– Remove nut with washer.
– Remove washer .
– Remove the timing chain sprocket !.
– Remove primary gear ".

16 ENGINE
102
– Remove woodruff key #.
308034-10
16.3.24 Removing the force pump
308035-10
308036-10
308037-10
308038-10
308039-10
– Remove lock ring . – Take off washer . – Remove the oil pump gear !.
– Remove pin ". – Take off the washer.
– Remove screws #. – Take off the pressure pump housing.
– Remove dowels $.
– Remove external rotor %. – Remove internal rotor &.

16 ENGINE
103
– Remove pin '. – Remove the oil pump shaft 02.
16.3.25 Removing the shift shaft
– Push sliding plate away from the shift drum locating . Remove shift shaft !
with the washer.
16.3.26 Removing the shift drum locating
– Remove screw . – Press locking lever away from shift drum locating ! and take off the shift drum
locating. – Release the locking lever.
16.3.27 Removing the locking lever
– Remove screw . – Take off locking lever together with the washers and spring.
16.3.28 Removing the oil filter
308040-10
308044-10
308045-10
308046-10
308047-10
– Remove screws . – Remove the oil filter cover with the O-ring.

16 ENGINE
104
308057-10 – Remove screws !. – Swing
the left section of the engine case up and remove the fitting of the engine fixing arm.
– Pull oil filter ! out of the oil filter housing.
Circlip pliers reverse (51012011000) ( p. 189)
308048-10
16.3.29 Removing the left engine case
308055-10
308056-10
– Remove special tool .
– Remove screw .

16 ENGINE
105
– Remove dowels $.
16.3.30 Removing the shift rails
– Remove shift rail together with upper spring and the lower spring. – Remove shift rail .
16.3.31 Removing the shift drum
308067-10
308068-10
309196-10
308059-10
308060-10
– Mount special tool ".
Pressure screw for crankshaft (90129020000) ( p. 194)
– Mount special tool # with suitable screws.
Case separating tool (90129048100) ( p. 195)
Info Use the drill hole marked with 902.
– Pull off the section of the engine case by screwing in the screw.
Info Do not wedge the engine case section. The washer of the main shaft usually sticks to the bearing.
– Take off the left section of the engine case. – Remove the special tool.
– Swing shift forks to one side. – Remove shift drum .

16 ENGINE
106
16.3.32 Removing the shift forks
– Remove shift forks .
16.3.33 Removing the transmission shafts
– Pull both transmission shafts out of the bearing seats together.
16.3.34 Removing the balancer shaft
– Remove screw . – Take off the lock washer. – Remove balancer shaft .
16.3.35 Removing the crankshaft
308061-10
308063-10
308064-10
308065-10
– Remove crankshaft .

16 ENGINE
107
16.4 Work on individual parts

16.4.1 Work on the left section of the engine case
309198-10
– Remove all dowels. – Remove lock ring . – Remove shaft seal ring of the shift shaft and ! of the countershaft. – Remove oil
nozzle ". – Remove any sealing mass remnants and clean the engine case section thoroughly. – Warm the engine case section in
an oven.
Guideline
150 °C (302 °F)
– Knock the engine case section against a level wooden plate. This will cause the
bearings to drop out of the bearing seats.
Info Any bearings that remain in the engine case section must be removed using a suitable tool.
– Insert the new cold bearings into the bearing seats of the hot engine case section and, if necessary, use a suitable press drift to
push the bearing all the way to the stop or so that it is flush.
Info When pressing the bearing in, ensure that the engine case section is level to prevent damage. Only press the bearings in via
the outer ring; otherwise, the bearings will be damaged when they are pressed in.
– After the engine case section has cooled, check that the bearings are firmly seated.
Info If the bearings are not firmly seated after cooling, it is likely that they will rotate in the engine case when warm. In this case,
the engine case must be renewed.
– Mount the dowels. – Press in shaft seal ring of the shift shaft with the open side facing inward so that
it is flush. – Press in shaft seal ring ! of the countershaft with the open side facing inward so
that it is flush. – Mount lock ring . – Mount and tighten oil nozzle ".
Guideline
Oil nozzle M5 6 Nm
(4.4 lbf ft)
Loctite® 243TM
– Blow out the oil channel with compressed air and check that it is clear.

16 ENGINE
108
16.4.2 Work on the right section of the engine case
– Remove all dowels. – Remove screws . Remove the bearing retainers. – Remove oil nozzle . – Remove nozzle !. – Remove any
sealing mass remnants and clean the engine case section thoroughly. – Warm the engine case section in an oven.
Guideline
150 °C (302 °F)
– Knock the engine case section against a level wooden plate. This will cause the
bearings to drop out of the bearing seats.
Info Any bearings that remain in the engine case section must be removed using a suitable tool.
– Insert the new cold bearings into the bearing seats of the hot engine case section and, if necessary, use a suitable press drift to
push the bearing all the way to the stop or so that it is flush.
Info When pressing the bearing in, ensure that the engine case section is level to prevent damage. Only press the bearings in via
the outer ring; otherwise, the bearings will be damaged when they are pressed in.
– After the engine case section has cooled, check that the bearings are firmly seated.
Info If the bearings are not firmly seated after cooling, it is likely that they will rotate in the engine case when warm. In this case,
the engine case must be renewed.
– Mount the dowels. – Position all bearing locks. – Mount and tighten screws .
Guideline
Screw, bearing retainer M6 12 Nm
(8.9 lbf ft)
308074-10
Loctite® 243TM
– Mount and tighten oil nozzle .
Guideline
Oil nozzle M6 6 Nm
(4.4 lbf ft)
Loctite® 243TM
– Mount and tighten nozzle !.
Guideline
Oil nozzle M5 6 Nm
(4.4 lbf ft)
Loctite® 243TM
– Blow compressed air through the oil channel and check that it is clear.
16.4.3 Changing the shaft seal ring of the water pump
308075-10
– Remove lock ring .

16 ENGINE
109
– Mount lock ring .
16.4.4 Checking the radial play of the lower conrod bearing
Condition The conrod bearing is bulging.
308076-10
308077-10
308076-10
308075-10
– Remove shaft seal ring .
– Remove shaft seal ring !. – Press the new shaft seal ring ! in all the way with the open side facing inward.
Mounting sleeve (90129043000) ( p. 195)
– Press shaft seal ring all the way in with the open side facing inward.

16 ENGINE
110
– Clamp the connecting rod with soft jaws. – Position the crankshaft. – Position the bearing shells. Insert the Plastigauge
clearance gauge offset by 90°
to the bearing face.
Plastigauge measuring strips (60029012000) ( p. 190)
– Position the conrod bearing cover. Mount and tighten the screws.
Guideline
Screw, conrod bearing M8x1 34 Nm
(25.1 lbf ft)
Info Do not twist the connecting rod.
– Remove the conrod bearing cover again. Compare the Plastigauge clearance gauge
with the specifications on the packaging. Guideline
Connecting rod - radial play of lower conrod bearing
308107-01
New condition 0.045... 0.068 mm (0.00177...
0.00268 in) Wear limit 0.080 mm (0.00315 in)
Info The width of the Plastigauge clearance gauge is equivalent to the bearing play.
– Clean the parts.
16.4.5 Changing the conrod bearing
308108-01
– Clamp the connecting rod with soft jaws. – Remove screws . – Remove the conrod bearing cover and crankshaft. Remove the
bearing shells.

16 ENGINE
111
– Position and oil the bearing shells. – Position the connecting rod and conrod bearing cover according to markings !. – Mount
and tighten screws .
Guideline
Screw, conrod bearing M8x1 34 Nm
(25.1 lbf ft)
16.4.6 Changing the balancer shaft bearing
308109-01
308110-01
308070-10
308071-10
– Measure the crank pin diameter.
Guideline
Crankshaft – diameter, crank pin
Crankshaft classification A 31.970... 31.977 mm (1.25866...
1.25893 in) Crankshaft classification B 31.978... 31.985 mm (1.25897...
1.25925 in)
Info The crankshaft classification is indicated by marking .
– Check the radial play of the lower conrod bearing. ( p. 109)
– Mount special tools .
Disassembly tool, balancer shaft bearing (90129056000) ( p. 196)
– Position the balancer shaft in the press using a suitable tool. – Press out the bearing.

16 ENGINE
112
– Press on the balancer shaft bearing with a suitable tool. – Remove the special tools.
Disassembly tool, balancer shaft bearing (90129056000) ( p. 196)
308072-10
16.4.7 Work on the cylinder head
308104-01
308105-01
308103-01
308105-01
– Fold cam lever up. – Take the shims out of the valve spring retainers and lay them to one side accord-
ing to their normal built-in position.
– Pretension the valve spring using the special tool.
Valve spring compressor (59029019000) ( p. 190) Insert for valve spring lever (77029041100) ( p. 193)
– Remove valve keys ! and relax the valve spring. – Remove valve spring retainer ". – Remove valve spring, valve stem seal #,
and valve spring seat $.
Info Place the valve into a box according to the installation position and label the box.
– Check the cylinder head. ( p. 113) – Mount valve spring seat $ and the new valve stem seal #. – Mount the valve spring. –
Mount valve spring retainer ".
– Pretension the valve spring using the special tool.
Valve spring compressor (59029019000) ( p. 190) Insert for valve spring lever (77029041100) ( p. 193)
– Mount valve keys. Relax the valve spring.
Info When mounting the valve keys, check that they are seated correctly; prefer- ably, fix the valve keys to the valve with a little
grease.
– Place shims into the valve spring retainers according to the installation position.

16 ENGINE
113
16.4.8 Checking the cylinder head
– Check sealing seat ( of the valves.
Valve - sealing seat width
Intake 0.90... 1.10 mm (0.0354...
0.0433 in)
Exhaust 0.90... 1.10 mm (0.0354...
0.0433 in)
» If the measured value does not equal the specified value:
– Machine the valve seat. – Blow compressed air through all oil holes and check that they are clear.
16.4.9 Checking the pivot point of the camshafts
308100-01
308101-01
302808-10
308091-01
308088-01
– Check valve guides with the special tool.
Limit plug gauge (77029026000) ( p. 193)
» If the special tool is easy to insert into the valve guide:
– Change the valve guides and valves. – Check the sealing area of the spark plug thread and the valve seats for damage
and
tearing. » If there is wear or tearing:
– Change the cylinder head.
– Check the sealing area of the cylinder for distortion using a straight edge and the
special tool.
Feeler gauge (59029041100) ( p. 190)
Cylinder/cylinder head - distortion of sealing area
≤ 0.10 mm (≤ 0.0039 in)
– Change the cylinder head.
– Check the pivot points of the camshafts.
» If there is damage or wear:
– Change the cylinder head with the camshaft bearing bridge.
– Position the camshafts.
The valves are not actuated. – Insert the Plastigauge clearance gauge in area (.
Plastigauge measuring strips (60029012000) ( p. 190)

16 ENGINE
114
– Remove the camshaft bearing bridge again. Compare the Plastigauge clearance
gauge with the data on the packaging. Guideline
Camshaft bearing - slide bearing
Radial clearance 0.025... 0.053 mm (0.00098...
Info The width of the Plastigauge clearance gauge is equal to the bearing play.
– Take off the camshafts and clean the parts.
16.4.10 Checking/measuring the cylinder
– Check the sealing area of the cylinder head for distortion using a straight edge and
the special tool.
Feeler gauge (59029041100) ( p. 190)
Cylinder/cylinder head - distortion of sealing area
≤ 0.10 mm (≤ 0.0039 in)
– Change the cylinder and piston.
16.4.11 Checking the piston ring end gap
308089-01
308090-01
308078-10
308079-10
308080-10
– Position camshaft bearing bridge . – Mount the screws and tighten in a crisscross pattern from the inside to the outside.
Guideline
Screw, camshaft bearing bridge M6 11 Nm (8.1 lbf ft)
Info Make sure the dowel pins are seated correctly. Do not twist the camshaft.
– Check the cylinder bearing surface for damage.
» If the cylinder bearing surface is damaged:
– Change the cylinder and piston. – Measure the cylinder diameter at several places in the . and / axes using a
micrometer to check for oval wear. Guideline
Cylinder - bore diameter 88.982... 88.998 mm (3.50322...
3.50385 in)
– Remove the piston ring from the piston. – Place the piston ring in the cylinder and align it with the piston.
Guideline
Under the upper edge of the cylinder 20 mm (0.79 in)
– Using special tool , measure the end gap.
Guideline
Piston ring end gap
Compression ring ≤ 0.40 mm (≤ 0.0157 in) Oil scraper ring ≤ 0.80 mm (≤ 0.0315 in)
Feeler gauge (59029041100) ( p. 190)
» If the end gap is more than the specified value: – Check/measure the cylinder. ( p. 114)

16 ENGINE
115
» If the cylinder wear is within the tolerance range:
– Change the piston ring. – Mount the piston ring with the marking facing toward the piston head.
16.4.12 Checking/measuring the piston
– Measure the piston at the piston skirt, at right angles to the piston pin, at a
distance ). Guideline
Distance ) 9 mm (0.35 in) Piston - diameter 88.931... 88.949 mm (3.50121...
3.50192 in)
16.4.13 Checking the piston/cylinder mounting clearance
– Check/measure the cylinder. ( p. 114) – Check/measure the piston. ( p. 115) – The piston/cylinder mounting clearance is the
result of the cylinder bore diameter
minus the piston diameter. Guideline
Piston/cylinder - mounting clearance
New condition 0.033... 0.067 mm (0.0013...
16.4.14 Checking the oil pump
Info The following operations apply to both oil pumps.
308081-01
308099-01
308081-01
– Check the piston bearing surface for damage.
» If the piston bearing surface is damaged:
– Change the piston and, if necessary, the cylinder. – Check that the piston rings can move easily in the piston ring grooves.
» If the piston ring is stiff:
– Clean the piston ring groove.
Tip Use an old piston ring to clean the piston ring groove.
– Check the piston rings for damage.
» If the piston ring is damaged:
– Change the piston ring.
Info Mount the piston ring with the marking facing upward.
– Check the piston pin for discoloration or signs of wear.
» If the piston pin has strong discoloration/signs of wear:
– Change the piston pin. – Insert the piston pin into the connecting rod and check the bearing for play.
» If the piston pin bearing has too much play:
– Change the connecting rod and the piston pin.

16 ENGINE
116
– Check axial play ( of the oil pump.
Oil pump
Axial play 0.10... 0.25 mm (0.0039...
0.0098 in)
» If the play exceeds the specification:
– Change the oil pump and, if necessary, the oil pump housing.
16.4.15 Checking the oil pressure regulator valve
308082-01
308083-01
308084-01
– With special tool , check the play between the internal rotor and external rotor
and between the external rotor and the oil pump housing.
Feeler gauge (59029041100) ( p. 190)
Oil pump
Play between external rotor and internal rotor
0.10... 0.20 mm (0.0039... 0.0079 in)
Oil pump
Play between external rotor and oil pump housing
0.09... 0.20 mm (0.0035... 0.0079 in)
» If the play exceeds the specification:
– Change the oil pump and, if necessary, the oil pump housing.
– Remove washer . – Remove spring . – Measure the length of spring .
Oil pressure regulator valve - minimum spring length
26.00 mm (1.0236 in)
» If the measured length is less than the specification:
– Change the spring. – Check control piston ! for damage and wear.
– Change the control piston. – Check the control piston in the pressure pump housing for smooth operation.
» If the control piston does not move easily:
– Change the control piston or the pressure pump housing. – Check the control piston bore in the pressure pump housing " for
damage and
wear. » If there is damage or wear:
– Change the pressure pump housing. – Thoroughly oil control piston ! and spring and mount. – Mount washer .

16 ENGINE
117
16.4.16 Checking the clutch
308085-01
– Check collar sleeve for damage and wear.
– Change the collar sleeve. – Check the length of clutch springs .
Clutch spring - length ≥ 37 mm (≥ 1.46 in)
» If the clutch spring length is less than the specified value:
– Change all clutch springs. – Check inner clutch hub ! for damage and wear.
– Change the inner clutch hub. – Check clutch pressure cap " for damage and wear.
– Change the clutch pressure cap. – Check the contact surfaces of the clutch facing discs in the outer clutch hub # for
wear.
Contact surface, clutch facing discs in clutch basket ≤ 0.5 mm (≤ 0.02 in)
» If the contact surface is very worn:
– Change the clutch facing discs and the outer clutch hub. – Check clutch facing discs $ for discoloration and scoring.
» If there is discoloration or scoring: – Change all clutch facing discs. – Check the thickness of clutch facing discs $ and
intermediate discs %.
Thickness of overall package ≥ 35.00 mm (≥ 1.378 in)
» If the clutch facing discs do not meet specifications:
– Change all clutch facing discs. – Check intermediate discs % for damage and wear.

16 ENGINE
118
» If the intermediate discs are not level or are pitted:
– Replace all intermediate discs.
16.4.17 Checking the shift mechanism
308086-01 – Check the shift forks (see ()
for damage and wear (visual check).
– Change the shift fork and gear wheel pair. – Check shift grooves ) of shift drum for wear.
» If the shift groove is worn:
– Change the shift roller. – Check the seat of the shift drum in bearing !. » If the shift roller is not seated correctly:
– Replace the shift drum and/or the bearing. – Check bearing ! for stiffness and wear.
» If the bearing is stiff or worn:
– Change the bearing. – Check shift rail " on a flat surface for run-out.
» If there is run-out:
– Change the shift rail. – Check the shift rail for scoring, signs of corrosion and stiffness in the shift forks.
» If there is scoring or corrosion, or if the shift fork is stiff:
– Change the shift rail. – Check sliding plate # in contact areas * for wear.
» If the sliding plate is worn: – Change the shift shaft. – Check return surface + on the sliding plate for wear.
» If deep notches are present:
– Change the shift shaft. – Check guide pin , for looseness and wear.
» If the guide pin is loose and/or worn:
– Change the shift shaft.

16 ENGINE
119
308096-01
– Fix the main shaft in the vise with the geared end facing downward.
Guideline
Use soft jaws.
– Remove stop disk and 2nd-gear fixed gear . – Remove the 5th-gear idler gear !. – Remove collar bushing ". – Remove lock ring
#. – Remove 3rd/4th-gear sliding gear $. – Remove lock ring %. – Remove collar bushing &. – Remove sixth-gear idler gear '.
– Preassemble the shift shaft. ( p. 119) – Check the play - between the sliding plate and the shift quadrant.
Shift shaft – play in sliding plate/shift quadrant
0.15... 0.45 mm (0.0059... 0.0177 in)
– Change the shift shaft.
16.4.18 Preassembling the shift shaft
– Fix the short end of the shift shaft in a vise.
Guideline
Use soft jaws.
– Mount sliding plate with the guide pin facing down and attach the guide pin to
the shift quadrant. – Mount preload spring . – Push on spring guide !, push return spring " over the spring guide with the
offset
end facing upward and lift the offset end over abutment bolt #. – Mount washer $.
16.4.19 Disassembling the main shaft
304514-10
304512-10

16 ENGINE
120
16.4.20 Dismantling the countershaft
308094-01
– Fix the countershaft in the vise with the geared end facing downward.
Guideline
Use soft jaws
– Remove stop disk and the 1st-gear idler gear . – Remove collar bushing !. – Remove the 6th-gear sliding gear ". – Remove lock
ring #. – Remove collar bushing $. – Remove the 3rd-gear idler gear %. – Remove washer &. – Remove the 4th-gear idler gear '.
– Remove fifth-gear sliding gear 02. – Remove the second-gear idler gear 03. – Remove collar bushing 04.
16.4.21 Checking the transmission
Condition The transmission has been disassembled.

16 ENGINE
121
308098-01
– Check collar bushings for damage and wear.
– Change the collar bushings. – Check the pivot points of main shaft and countershaft ! for damage and wear.
– Change the main shaft and/or countershaft. – Check the tooth profiles of main shaft and countershaft ! for damage and
wear.
– Change the main shaft and/or countershaft. – Check the pivot points of idler gears " for damage and wear.
– Change the gear wheel pair. – Check the shift dogs of idler gears " and sliding gears # for damage and wear.
– Change the gear wheel pair. – Check the tooth faces of idler gears ", sliding gears #, and fixed gear $ for damage and
wear.
– Change the gear wheel pair. – Check the tooth profiles of sliding gears # for damage and wear.
– Change the gear wheel pair. – Check sliding gears # for smooth operation in the profile of main shaft .
» If the sliding gear does not move easily:
– Change the sliding gear or the main shaft. – Check sliding gears # for smooth operation in the profile of countershaft !.
» If the sliding gear does not move easily:
– Change the sliding gear or the countershaft. – Check stop disks % for damage and wear.
– Change the stop disk. – Use new lock rings & with every repair.
16.4.22 Assembling the main shaft
Info Use new lock rings in every repair job.

16 ENGINE
122
Preparatory work – Oil all parts carefully before assembling. – Check the transmission. ( p. 120)
308097-01
Main work – Fix the main shaft in the vise with the geared end facing downward.
Guideline
Use soft jaws
– Mount sixth-gear idler gear . – Mount collar bushing . – Mount lock ring !. – Mount third/fourth-gear sliding gear " with the
small gear wheel facing up. – Mount lock ring #. – Mount collar bushing $. – Mount fifth-gear idler gear %. – Mount second-gear
fixed gear & and stop disk '. – Finally, check all gear wheels for smooth operation.
16.4.23 Assembling the countershaft
Info Use new lock rings in every repair job.
Preparatory work – Oil all parts carefully before assembling. – Check the transmission. ( p. 120)

16 ENGINE
123
308095-01
Main work – Fix the countershaft in the vise with the geared end facing downward.
Guideline
Use soft jaws
– Mount collar bushing . – Mount second-gear idler gear . – Mount the fifth-gear sliding gear ! with the shift groove facing
upward. – Mount fourth-gear idler gear ". – Mount washer #. – Mount third-gear idler gear $. – Mount collar bushing %. – Mount
lock ring &. – Mount sixth-gear sliding gear ' with the shift groove facing downward. – Mount collar bushing 02. – Mount
first-gear idler gear 03. – Mount stop disk 04. – Replace O-ring 05 of the countershaft. – Finally, check all gear wheels for
smooth operation.

16 ENGINE
124
16.4.24 Checking the timing assembly
308087-01
– Check timing chain for damage and wear.
– Change the timing chain. – Let the timing chain hang down freely. Check that the timing chain links move easily.
» If the chain links no longer straighten out:
– Change the timing chain. – Check timing chain guide rail for damage and wear.
– Change the timing chain guide rail. – Check timing chain tensioning rail ! for damage and wear.
– Change the timing chain tensioning rail. – Check timing chain sprocket " for damage and wear.
– Change the timing chain sprocket. – Check camshaft gears # for damage and wear.
– Change the camshaft gears.
16.4.25 Changing the stator
308092-01
– Remove screws . – Remove the cable retainer.

16 ENGINE
125
304530-10
– Check the teeth and seating of the starter idler gear for damage and wear.
– Change the starter idler gear. – Check the teeth and seating of the torque limiter for damage and wear.
– Change the torque limiter. – Check the toothing and bearing of freewheel gear ! for damage and wear.
– Replace the freewheel gear and/or the bearing. – Check toothing " of the starter motor for damage and wear.
– Replace the starter motor. – Replace the O-ring # of the starter motor. – Clamp the minus (negative) cable of a 12 Volt
power supply to the starter motor housing. Briefly connect the positive cable of the
power supply to the starter motor connection. » If the starter motor does not turn when you close the power circuit:
Loctite® 243TM
16.4.26 Checking the electric starter drive
308093-01
308092-01
– Remove screws . – Remove the stator. – Position the new stator. – Mount and tighten screws .
Guideline
Screw, stator M5 8 Nm
(5.9 lbf ft)
– Position the cable guide in the alternator cover. – Position the cable retainer. – Mount and tighten screws .
Guideline
Screw, retaining bracket, stator cable
M5 8 Nm
(5.9 lbf ft)
Loctite® 243TM

16 ENGINE
126
– Replace the starter motor.
16.4.27 Checking the freewheel
– Insert freewheel gear into the freewheel hub by turning the freewheel gear clock-
wise; do not wedge! – Check the locking action of the freewheel gear.
» If the freewheel gear does not turn clockwise or if it does not lock counterclock-
wise: – Replace the freewheel.
16.5 Assembling the engine

16.5.1 Installing the crankshaft
– Oil the bearing. – Slide crankshaft into the bearing seat.
16.5.2 Installing the balancer shaft
304255-10
308065-10
308069-10
308064-11
– Mount special tool .
– Mount balancer shaft with the bearing.
Info If necessary, heat the engine case.
– Position the retaining bracket. – Mount and tighten screw !.
Guideline
Screw, bearing retainer M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM
– Remove the special tool.

16 ENGINE
127
16.5.3 Installing the transmission shafts
– Oil the bearing. – Slide both transmission shafts into the bearing seats together.
16.5.4 Installing the shift forks
– Oil all parts carefully before assembling. – Shift fork has a smaller inside diameter; mount it in the shift groove of the main
shaft. – Mount shift fork in the lower shift groove of the countershaft. – Mount shift fork ! in the upper shift groove of the
countershaft.
16.5.5 Installing the shift drum
– Slide shift drum into the bearing seat. – Hang shift forks into the shift drum.
16.5.6 Installing the shift rails
308063-10
308062-10
308060-11
308059-10
– Oil all parts carefully before assembling. – Mount shift rail together with upper spring and the lower spring. – Mount shift rail .

16 ENGINE
128
16.5.7 Installing the left engine case
309200-10
– Mount the engine case section. If necessary, tap lightly with a rubber mallet while turning the transmission shafts.
Info Do not tighten the engine case sections using the screws.
– Mount screws ! but do not tighten them yet.
Guideline
Screw, engine case M6x75 12 Nm (8.9 lbf ft)
– Mount screws " and tighten all screws in a crisscross pattern.
Guideline
– Mount the fitting of the engine fixing arm.
308058-11
309199-10
– Clean the sealing areas. – Mount dowels .
– Mount the new O-rings on oil spray tube . – Mount the oil spray tube.
Catch ( engages in recess ). – Apply sealing compound to the left section of the engine case.
Loctite® 5910

16 ENGINE
129
– Position crankshaft to TDC and block with special tool $.
16.5.8 Installing the oil filter
– Oil the O-ring of the oil filter cover. – Install the oil filter cover . – Mount and tighten screws !.
Guideline
Screw, oil filter cover M5 8 Nm (5.9 lbf ft)
16.5.9 Installing the locking lever
309201-10
309202-10
308048-11
308047-11
308046-11
– Mount and tighten screw #.
Guideline
– Tilt the engine sideways and fill the oil filter housing approx. 1⁄3 full with engine oil. – Fill oil filter with engine oil and insert it
in the oil filter housing.
– Mount locking lever with the sleeve, washers and spring. – Mount and tighten screw with the washer.
Guideline
Screw, locking lever M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM

16 ENGINE
130
16.5.10 Installing the shift drum locating
– Mount spacer ring on the shift drum locating unit. – Press locking lever away from the shift drum locating and position the shift
drum
locating !.
Pins ( engage in hole ). – Release the locking lever. – Mount and tighten screw ".
Guideline
Screw, shift drum locating M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM
16.5.11 Installing the shift shaft
– Slide shift shaft with the washer into the bearing seat. – Push sliding plate away from the shift drum locating !. Insert the shift
shaft all
the way. – Let the sliding plate engage in the shift drum locating. – Shift through the transmission.
16.5.12 Installing the oil pump
308049-10
308044-11
308041-10
308042-10
– Mount dowels .
– Position pin and internal rotor ! on the oil pump shaft.

16 ENGINE
131
– Position the oil pump gear %. – Position washer &. – Mount lock ring '. – Crank the oil pump gear and check for stiffness.
16.5.13 Installing the primary gear
308043-10
308037-10
308036-11
308035-11
308034-11
308033-11
– Position the oil pump shaft with the internal rotor in the pressure pump housing. – Position external rotor " in the pressure
pump housing.
Markings ( are visible after assembly.
– Check that the oil holes are clear and fill with a small amount of oil. – Position the oil pump. – Mount and tighten screws #.
Guideline
Screw, oil pump M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM
– Position the washer. – Position pin $.
– Mount woodruff key .
– Mount primary gear .

16 ENGINE
132
Loctite® 243TM
16.5.14 Installing the clutch cage
308032-10
308031-11
308030-11
308028-11
308029-10
308027-11
– Mount timing chain sprocket !.
– Mount washer ".
– Mount and tighten nut # with the washer.
Guideline
Nut, primary gear/timing chain sprocket
M16x1.5 120 Nm
(88.5 lbf ft)
– Mount collar sleeve .
– Slide clutch basket onto the main shaft. – Turn oil pump gear ! until the gear teeth of the clutch basket engage.
– Slide on washer " and inner clutch hub #.

16 ENGINE
133
– Position pressure cap 03. – Mount screws 04 with the washers and springs and tighten them in a crisscross pat-
tern. Guideline
Screw, clutch spring M6 10 Nm (7.4 lbf ft)
16.5.15 Installing the spacer
308026-10
308053-10
308054-10
308024-11
308023-11
308022-10
– Mount nut $ with the washer. Hold the inner clutch hub with the special tool and
tighten the nut. Guideline
Nut, inner clutch hub M16LHx1.5 120 Nm
(88.5 lbf ft)
Loctite® 243TM
Clutch holder (51129003000) ( p. 189)
– Mount support ring % and pretension ring &.
The inside of the pretension ring rests against the support ring and the outside faces away from the support ring.
– Oil the clutch facing discs thoroughly. – Mount the clutch facing disc ' with the largest inside diameter. – Alternately mount all
of the other intermediate clutch discs and clutch facing discs.
– Mount pull rod 02.
– Grease the shaft seal ring of the countershaft before mounting.
– Mount spacer .

16 ENGINE
134
16.5.16 Installing the suction pump
308020-11
308021-10
308018-11
308017-11
– Position pin .
– Mount internal rotor and external rotor !.
Marking ( of the external rotor is not visible after assembly.
– Mount dowels ".
– Oil the oil pump. – Position the oil pump housing. – Mount and tighten screws #.
Guideline
Screw, oil pump M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM

16 ENGINE
135
16.5.17 Installing the gear position sensor
Loctite® 243TM
– Mount and tighten screws ".
Guideline
Screw, retaining bracket M5 6 Nm
(4.4 lbf ft)
Loctite® 243TM
16.5.18 Installing the balancer shaft drive wheel
308016-11
308015-11
308014-11
308050-10
308051-10
– Mount the contact spring and contact pin .
The rounded sides of the contact pins face the sensor.
– Install the gear position sensor. – Mount and tighten screws .
Guideline
Screw, gear sensor M5 6 Nm
(4.4 lbf ft)
– Position the cable guide in the engine case. – Position the retaining bracket.
Info Ensure that the cable is correctly routed.
– Position the ignition pulse generator. – Mount and tighten screws !.
Guideline
Screw, ignition pulse generator
M5 6 Nm
(4.4 lbf ft)
– Mount the spring washer. – Mount drive wheel of the balancer shaft.
– Mount washer .
The outer side of the washer is in contact with the drive wheel and the inside faces away from the drive wheel.
Loctite® 243TM

16 ENGINE
136
Loctite® 243TM
16.5.19 Installing the starter drive
308012-10
308052-10
308010-11
308009-11
308008-11
308007-11
– Mount and tighten nut !.
Guideline
Nut, drive wheel for balancer shaft M28 60 Nm
(44.3 lbf ft)
– Position balancer shaft gear ".
Markings ( and ) align. – Mount wedge #.
– Mount and tighten screw $.
Guideline
Screw, balancer shaft gear M8 20 Nm
(14.8 lbf ft)
– Position freewheel gear .
– Position the retaining bracket. – Mount and tighten screw .
Guideline
Screw, freewheel gear retaining bracket
– Mount starter idler gear !. – Mount torque limiter ".
M6 12 Nm
(8.9 lbf ft)
Loctite® 243TM

16 ENGINE
137
16.5.20 Installing the rotor
– Mount the spring washer. – Mount the rotor.
Info Turn the freewheel gear counterclockwise to simplify assembly.
– Mount and tighten screw .
Guideline
Rotor screw M10 75 Nm
(55.3 lbf ft)
Loctite® 243TM
16.5.21 Installing the alternator cover
– Position the alternator cover. – Install the screws ! and tighten them diagonally.
Guideline
Screw, alternator cover M6 12 Nm (8.9 lbf ft)
16.5.22 Installing the water pump cover
308005-10
308004-11
308003-11
308002-11
308001-11
– Mount the dowels . – Seal the cable guide.
Loctite® 5910
– Mount the alternator cover gasket .
– Mount water pump impeller . – Mount and tighten nut with the washer.
Guideline
Nut, water pump impeller M6 10 Nm
(7.4 lbf ft)
– Mount locating pins !.
Loctite® 243TM

16 ENGINE
138
– Mount the water pump cover with the seal ring. – Mount screws " and tighten them in a crisscross pattern.
Guideline
Screw, water pump cover M6 12 Nm (8.9 lbf ft)
16.5.23 Installing the timing chain
– Position timing chain in the engine case according to the direction of travel.
16.5.24 Installing the starter motor
– Grease the O-ring. Position the starter motor.
Guideline
Screw, starter motor M6 12 Nm (8.9 lbf ft)
16.5.25 Installing the piston
308000-11
307999-11
307998-11
307997-10
307992-10
– Feed in the timing chain tensioning rail from above. – Mount and tighten screw .
Guideline
Screw, timing chain tensioning rail
M6 12 Nm
(8.9 lbf ft)
– Shift the joint of the piston rings by 120°. – Place the special tool onto the oiled piston. Clamp the piston rings together using
the special tool.
Piston ring mounting tool (60029015000) ( p. 190)
The piston ring are squeezed together fully.
Loctite® 243TM

16 ENGINE
139
307993-10
307994-10
307995-10
307991-11
307990-11
– Position the piston with the special tool on the cylinder. – Carefully slide the piston into the cylinder from the top.
Info The piston rings should not become caught; otherwise, they may be damaged.
– Ensure that piston marking ( faces the outfeed side.
– Thinly apply sealing compound to area ).
Loctite® 5910
– Position the cylinder base gasket.
– Mount dowels and position the cylinder base gasket .
– Feed the timing chain through the chain shaft. Mount piston pin !.

16 ENGINE
140
– Cover the engine case opening with a cloth. – Position piston ring lock ".
6-o'clock position. – Insert the special tool and firmly press it toward the piston.
Insert for piston pin retainer (77329030100) ( p. 193)
– Turn the special tool clockwise, thereby pressing the piston pin retainer into the
groove. – Make sure that the piston pin retainer is seated correctly on both sides. – Remove the cloth. – Keep the timing
chain tensioned. Push the cylinder down carefully and let the dow-
els engage.
307996-10
16.5.26 Installing the cylinder head
307989-10
307987-11
307986-11
– Position timing chain guide rail .
Pins ( engage in recess ). The timing chain guide rail engages in recess *.
– Mount dowels . – Put on cylinder head gasket !. – Mount the cylinder head.
– Mount screws " with the washer and tighten in a crisscross pattern.
Guideline
Screw, cylinder head M10 1st stage
30 Nm (22.1 lbf ft) 2nd stage 60 Nm (44.3 lbf ft)
Thread is oiled, head flat is greased

16 ENGINE
141
– Mount and tighten screws #.
Guideline
Cylinder head screw M6 12 Nm (8.9 lbf ft)
16.5.27 Installing the camshafts
– Thoroughly clean all oil jets and blow through with compressed air. – Mount the dowels. – Position the camshaft bearing
bridge. – Mount screws and tighten from the inside to the outside.
Guideline
Screw, camshaft bearing bridge M6 11 Nm (8.1 lbf ft)
16.5.28 Installing the timing chain tensioner
307985-11
307984-10
307981-11
304804-10
– Oil the camshafts and pivot points. – Ensure that the crankshaft is blocked in the TDC position. – Pull up the timing chain and
insert exhaust camshaft . – Place the timing chain over the camshaft gear of the intake camshaft.
Markings ( of the camshafts align with the edge of the cylinder head.
– Turn the timing chain tensioner screw clockwise.
The timing chain tensioner is locked.

16 ENGINE
142
– Mount and tighten screw ! with the O-ring.
Guideline
Screw, unlocking of timing chain tensioner
M6 10 Nm (7.4 lbf ft)
16.5.29 Checking the valve clearance
307980-10
307979-11
307978-11
307965-10
307968-11
– Holding it with the correct orientation, mount the timing chain tensioner with
the gasket. – Mount and tighten screws .
Guideline
Screw, timing chain tensioner M6 12 Nm (8.9 lbf ft)
– Unlock the timing chain tensioner screw counterclockwise. – Check the timing chain tension.
– Remove the special tool.
– Crank the engine several times. – Set the engine to ignition top dead center. ( p. 92) – Check the valve clearance at all valves
between the camshaft and cam lever.
Guideline
Valve clearance, exhaust, cold 0.13... 0.17 mm (0.0051...
0.0067 in) Valve clearance, intake, cold 0.08... 0.12 mm (0.0031...
0.0047 in)
Feeler gauge (59029041100) ( p. 190)
» If valve clearance does not meet specifications: – Adjust the valve clearance. ( p. 143)
– Mount and tighten screw plug .
Guideline
Screw plug, alternator cover M18x1.5 10 Nm (7.4 lbf ft)

16 ENGINE
143
– Mount and tighten screws ".
Guideline
Screw plug M8 12 Nm (8.9 lbf ft)
16.5.30 Adjusting the valve clearance
Preparatory work – Remove the timing chain tensioner. ( p. 93) – Remove the camshaft. ( p. 93)
Main work – Swing up cam lever . – Correct the shims as indicated by the results of the valve clearance check.
Finishing work – Install the camshafts. ( p. 141) – Install the timing chain tensioner. ( p. 141) – Check the valve clearance. ( p.
142)
16.5.31 Installing the clutch cover
307967-11
307976-11
307975-11
307977-10
307974-11
– Mount and tighten screw plug .
Guideline
Screw plug, alternator cover M24x1.5 10 Nm (7.4 lbf ft)
– Remove special tool !.
– Mount dowel and clutch cover gasket .

16 ENGINE
144
– Mount and tighten screws !.
Guideline
Screw, clutch cover M6 12 Nm (8.9 lbf ft)
16.5.32 Installing the spark plug
– Mount and tighten the spark plug using special tool .
Guideline
Spark plug M12 15 Nm
(11.1 lbf ft)
Spark plug wrench (77229172000) ( p. 193)
16.5.33 Installing the valve cover
307973-10
307972-11
307966-10
307963-11
307962-10
– Position the clutch cover.
Info Pivot the clutch lever.
– Grease the O-rings and mount spark plug shaft insert .
– Mount gasket .

16 ENGINE
145
– Position the valve cover with the gasket. – Mount and tighten screws ! with the gaskets.
Guideline
Screw, valve cover M6 12 Nm (8.9 lbf ft)
16.5.34 Installing the chain securing guide
Loctite® 243TM
16.5.35 Installing the oil screen
307964-10
307961-11
307960-10
307959-11
– Degrease the sealing areas and thinly coat with sealant in areas ( and ).
Loctite® 5910
– Position the gasket in the valve cover.
– Position the chain securing guide. – Mount and tighten screws .
Guideline
Screw, chain securing guide
M6 11 Nm
(8.1 lbf ft)
– Mount and tighten screw plug with the O-ring and oil screen.
Guideline
Oil screen screw plug, small M17x1.5 12 Nm (8.9 lbf ft)

16 ENGINE
146
– Mount and tighten oil drain plug ! with the O-ring.
Guideline
Oil drain plug M24x1.5 15 Nm
(11.1 lbf ft)
16.5.36 Removing the engine from the engine assembly stand
307958-10
307957-11
307956-10
– Mount oil screen with the O-ring.
– Remove the fitting from special tools and .
Engine fixing arm (90129002060) ( p. 194) Engine fixing arm (90129002050) ( p. 193)
– Remove the engine from the engine assembly stand.
Info Have an assistant help you or use a crane.

17 SHIFT MECHANISM
147
17.1 Adjusting the shift lever

Info The adjustment range of the shift lever is limited.
101927-10
– Loosen nuts . – Adjust the shift lever by turning shift rod .
Guideline
Shift rod adjustment range ( 110... 122 mm (4.33... 4.8 in)
Info Make the same adjustments on both sides. At least five screw threads must be screwed into the seating.
– Check adjusting angle ).
Guideline
Adjusting angle ) shift rod - linkage - shift lever
75°
– Tighten nuts .
Info After the nuts have been tightened, the bearings of the shift rod must be central and aligned identically to each other in order
to ensure freedom of movement in the bearing shells.
– Check the shift lever to ensure it is functioning properly and can move freely.

18 WATER PUMP, COOLING SYSTEM
148
18.1 Draining the coolant

Warning Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure.
– Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.
Warning Danger of poisoning Coolant is poisonous and a health hazard.
– Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swallowed,
contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of children.
Condition The engine is cold. Preparatory work – Remove the front spoiler. ( p. 47)
Main work – Stand the motorcycle upright. – Place a suitable container under the engine. – Remove screw . – Remove the
radiator cap. – Completely drain the coolant. – Mount screw with a new seal ring and tighten it.
Guideline
Plug, water pump drain hole M6 8 Nm (5.9 lbf ft)
18.2 Filling/bleeding the cooling system

101912-10
101911-11
101913-10
– Remove radiator cap .
– Open bleeder screw by three turns. – Tilt the vehicle slightly to the right. – Pour in coolant until it emerges without bubbles at
the bleeder screw, and then
mount and tighten the bleeder screw immediately. Alternative 1
Coolant ( p. 186)
Alternative 2
Coolant (mixed ready to use) ( p. 186)
– Fill the radiator completely with coolant. Mount the radiator cap.

149
– Rest the vehicle on the side stand.
– Start the engine and let it run warm.
– Stop the engine and allow it to cool down. – When the engine is cool, check the coolant level in the radiator and, if necessary,
add coolant. – Remove the cap of the compensating tank ! and add coolant until the coolant
level is up to the MAX mark. – Mount the cap of the compensating tank. – Fit the front spoiler. ( p. 47)
101910-11
18.3 Checking the antifreeze and coolant level

Condition The engine is cold.
101910-10
– Stand the motorcycle upright on a horizontal surface. – Remove the cap of the compensating tank . – Check the coolant
antifreeze.
−25... −45 °C (−13... −49 °F)
» If the coolant antifreeze does not meet specifications:
– Correct the coolant antifreeze. – Check the coolant level in the compensating tank.
The coolant level must be between MIN and MAX.
» If the coolant level does not meet specifications:
– Correct the coolant level.
Alternative 1
Coolant ( p. 186)
Alternative 2
– Mount the cap of the compensating tank.

150
– Remove radiator cap . – Check the coolant antifreeze.
−25... −45 °C (−13... −49 °F)
» If the coolant antifreeze does not meet specifications:
– Correct the coolant antifreeze. – Check the coolant level in the radiator.
The radiator must be completely filled. 101911-10
– Correct the coolant level and find out the cause of the loss.
Alternative 1
Coolant ( p. 186)
Alternative 2
» If you had to add more coolant than the specified amount:
> 0.20 l (> 0.21 qt.) – Fill/bleed the cooling system. ( p. 148) – Mount the radiator cap.
18.4 Checking the coolant level

Condition The engine is cold.
101910-10
101911-10
– Stand the motorcycle upright on a horizontal surface. – Check the coolant level in the compensating tank .
The coolant level must be between MIN and MAX.
– Correct the coolant level.
Alternative 1
Coolant ( p. 186)
Alternative 2
– Remove radiator cap and check the coolant level in the radiator.
The radiator must be completely filled.
– Correct the coolant level and find out the cause of the loss.
Alternative 1
Coolant ( p. 186)
Alternative 2

151
» If you had to add more coolant than the specified amount:
> 0.20 l (> 0.21 qt.) – Fill/bleed the cooling system. ( p. 148) – Mount the radiator cap.

19 LUBRICATION SYSTEM
152
19.1 Oil circuit

1 Suction pump 2 Force pump 3 Oil filter 4 Oil pressure regulator valve 5 Oil jet for piston cooling 6 Oil spray tube 7 Oil jet for
cam follower lubrication
19.2 Checking the engine oil level

Condition The engine is at operating temperature. Preparatory work – Stand the motorcycle upright on a horizontal surface.
Main work – Check the engine oil level.
Info After switching off the engine, wait one minute before checking the level.
The engine oil must be between the lower and upper edge of the oil level viewer.
» If the engine oil level is not at the specified level:
– Add the engine oil. ( p. 155)
19.3 Checking the engine oil pressure

Warning Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden.
– Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.
308470-10
101916-10
308270-10
Main work – Place a suitable container under the engine. – Remove screws . Take off the oil filter cover with the O-ring.

153
308271-10
308272-10
– Remove oil filter .
– Position the special tool with the O-ring. Mount and tighten the screws.
Guideline
Oil pressure adapter (75029094000) ( p. 192)
– Connect the pressure tester to the special tool without the T-plate.
Pressure testing tool (61029094000) ( p. 191)
– Check the engine oil level. ( p. 152)
– Start the engine. – Check the engine oil pressure.
Engine oil pressure
Coolant temperature: ≥ 70 °C (≥ 158 °F) Engine speed: 1,500 rpm
≥ 0.7 bar (≥ 10 psi)
Coolant temperature: ≥ 70 °C (≥ 158 °F) Engine speed: 5,000 rpm
≥ 2.4 bar (≥ 35 psi)
» If the specification is not reached:
– Check oil pumps for wear. Check all oil channels for free flow. – Switch off the engine.
Warning Danger of burns Some vehicle components get very hot when the machine is driven. – Wear appropriate protective
clothing and safety gloves. In case of burns,
rinse immediately with lukewarm water.
– Remove the special tools. – Insert the new oil filter. – Oil the O-ring of the oil filter cover. Mount the oil filter cover. – Mount
and tighten the screws.
Guideline
Finishing work – Check the engine oil level. ( p. 152)

154
19.4 Changing the engine oil and oil filter, cleaning the oil screen
Warning Danger of scalding Engine oil and gear oil get very hot when the motorcycle is ridden.
– Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.
Info Drain the engine oil only when the engine is warm.
Preparatory work – Remove the front spoiler. ( p. 47) – Stand the motorcycle on its side stand on a horizontal surface.
101917-10
101918-10
101919-10
Main work – Place a suitable container under the engine. – Remove the oil drain plug with the O-ring. – Remove oil screen with
the O-ring. – Remove screw plug ! with oil screen ". – Completely drain the engine oil. – Thoroughly clean the oil drain plugs
and oil screens. – Position oil screen and mount and tighten oil drain plug with the O-ring.
Guideline
Oil drain plug M24x1.5 15 Nm
(11.1 lbf ft)
– Mount and tighten screw plug ! with oil screen " and the O-ring.
Guideline
Oil screen screw plug, small M17x1.5 12 Nm (8.9 lbf ft)
– Remove screws #. Remove the oil filter cover $ with the O-ring. – Pull oil filter % out of the oil filter housing.
– Completely drain the engine oil. – Thoroughly clean the parts and sealing area.
– Insert oil filter %. – Oil the O-ring of the oil filter cover. Mount oil filter cover $. – Mount and tighten the screws.
Guideline
Info Too little engine oil or poor-quality engine oil results in premature wear to the engine.

155
– Remove the oil filler plug & with the O-ring from the clutch cover and fill up with
engine oil.
– Install and tighten the oil filler plug with the O-ring.
101920-10
– When running the engine, always make sure there is sufficient ventila-
– Start the engine and check that it is oil-tight. Finishing work – Fit the front spoiler. ( p. 47) – Check the engine oil level. ( p.
152)
19.5 Adding engine oil

Info Too little engine oil or poor-quality engine oil results in premature wear to the engine.
101921-10
Main work – Remove the oil filler plug with the O-ring from the clutch cover and fill up with
engine oil.
Engine oil (SAE 15W/50) ( p. 186)
Info For optimal performance of the engine oil, do not mix different types of engine oil. If appropriate, change the engine oil.
– Install and tighten the oil filler plug with the O-ring.
– Start the engine and check that it is oil-tight. Finishing work – Check the engine oil level. ( p. 152)

20 IGNITION SYSTEM
156
20.1 Alternator - checking the stator winding

304934-10 Stator winding - check the
short circuit to ground (terminal 31) –
Measure the resistance between the specified points. Stator, connector HB pin 1 – Measuring point Ground (−)
Resistance ∞ Ω
» If the displayed value does not equal the setpoint value:
– Change the stator.
L00082-10
L00082-10
Stator winding, measurement I - check the resistance –
Measure the resistance between the specified points. Stator, connector HB pin 1 – Stator, connector HB pin 2
Alternator
Resistance of stator winding at: 20 °C (68 °F)
≤ 1 Ω
– Change the stator. Stator winding, measurement II - check the resistance –
Measure the resistance between the specified points. Stator, connector HB pin 1 – Stator, connector HB pin 3
Alternator
Resistance of stator winding at: 20 °C (68 °F)
≤ 1 Ω
– Change the stator.

21 TECHNICAL DATA
157
21.1 Engine
Design 1-cylinder 4-stroke engine, water-cooled Displacement 375 cm3 (22.88 cu in) Stroke 60 mm (2.36 in) Bore 89 mm (3.5
in) Compression ratio 12.8:1 Control DOHC, 4 valves controlled via cam lever, chain drive Valve diameter, intake 36 mm (1.42
in) Valve diameter, exhaust 29 mm (1.14 in) Valve clearance, intake, cold 0.08... 0.12 mm (0.0031... 0.0047 in) Valve clearance,
exhaust, cold 0.13... 0.17 mm (0.0051... 0.0067 in) Crankshaft bearing 2 slide bearings Conrod bearing Sleeve bearing Pistons
Forged light alloy Piston rings 1 compression ring, 1 tapered compression piston ring, 1 oil
scraper ring Engine lubrication Pressure circulation
lubrication with two rotary pumps Primary transmission 30:80 Clutch Clutch in oil bath/mechanically activated Transmission
6-gear, claw shifted Transmission ratio
1st gear 12:32 2nd gear 14:26 3rd gear 19:27 4th gear 21:24 5th gear 23:22 6th gear 25:21 Mixture preparation Electronically
controlled fuel injection Ignition Contactless controlled fully electronic ignition with digital igni-
tion adjustment Alternator 12 V, 238 W Spark plug
BOSCH VR 5 NE Spark plug electrode gap 0.8 mm (0.031 in) Cooling Water cooling, permanent circulation of coolant by water
pump Idle speed 1,550... 1,650 rpm Starting aid Electric starter
21.2 Engine tolerance, wear limits

Intake 0.90... 1.10 mm (0.0354... 0.0433 in) Exhaust 0.90... 1.10 mm (0.0354... 0.0433 in) Cylinder/cylinder head - distortion of
sealing area ≤ 0.10 mm (≤ 0.0039 in) Cylinder - bore diameter 88.982... 88.998 mm (3.50322... 3.50385 in) Piston - diameter
88.931... 88.949 mm (3.50121... 3.50192 in) Piston/cylinder - mounting clearance
New condition 0.033... 0.067 mm (0.0013... 0.00264 in) Wear limit 0.08 mm (0.0031 in) Piston ring end gap
Compression ring ≤ 0.40 mm (≤ 0.0157 in) Oil scraper ring ≤ 0.80 mm (≤ 0.0315 in) Connecting rod - radial play of lower conrod
bearing
New condition 0.045... 0.068 mm (0.00177... 0.00268 in)

21 TECHNICAL DATA
158
Wear limit 0.080 mm (0.00315 in) Crankshaft – diameter, crank pin
Crankshaft classification A 31.970... 31.977 mm (1.25866... 1.25893 in) Crankshaft classification B 31.978... 31.985 mm
(1.25897... 1.25925 in) Clutch facing discs – thickness of total package ≥ 21.30 mm (≥ 0.8386 in) Clutch spring - length ≥ 37 mm
(≥ 1.46 in) Contact surface, clutch facing discs in clutch basket ≤ 0.5 mm (≤ 0.02 in) Oil pressure regulator valve - minimum
spring length 26.00 mm (1.0236 in) Oil pump
Play between external rotor and oil pump housing 0.09... 0.20 mm (0.0035... 0.0079 in) Play between external rotor and internal
rotor 0.10... 0.20 mm (0.0039... 0.0079 in) Axial play 0.10... 0.25 mm (0.0039... 0.0098 in) Shift shaft – play in sliding plate/shift
quadrant 0.15... 0.45 mm (0.0059... 0.0177 in)
21.3 Engine tightening torques

Oil nozzle M5 6 Nm (4.4 lbf ft) Loctite® 243TM Screw, gear sensor M5 6 Nm (4.4 lbf ft) Loctite® 243TM Screw, ignition pulse
generator M5 6 Nm (4.4 lbf ft) Loctite® 243TM Screw, oil filter cover M5 8 Nm (5.9 lbf ft) – Screw, retaining bracket M5 6 Nm
(4.4 lbf ft) Loctite® 243TM Screw, retaining bracket, stator cable M5 8 Nm (5.9 lbf ft) Loctite® 243TM Screw, stator M5 8 Nm
(5.9 lbf ft) Loctite® 243TM Cylinder head screw M6 12 Nm (8.9 lbf ft) – Nut, water pump impeller M6 10 Nm (7.4 lbf ft)
Loctite® 243TM Plug, water pump drain hole M6 8 Nm (5.9 lbf ft) – Screw, alternator cover M6 12 Nm (8.9 lbf ft) – Screw,
bearing retainer M6 12 Nm (8.9 lbf ft) Loctite® 243TM Screw, camshaft bearing bridge M6 11 Nm (8.1 lbf ft) – Screw, chain
securing guide M6 11 Nm (8.1 lbf ft) Loctite® 243TM Screw, clutch cover M6 12 Nm (8.9 lbf ft) – Screw, clutch spring M6 10
Nm (7.4 lbf ft) – Screw, engine case M6x40 12 Nm (8.9 lbf ft) – Screw, engine case M6x60 12 Nm (8.9 lbf ft) Loctite® 243TM
Screw, engine vent plate M6 10 Nm (7.4 lbf ft) Loctite® 243TM Screw, freewheel gear retaining bracket M6 12 Nm (8.9 lbf ft)
Loctite® 243TM Screw, locking lever M6 12 Nm (8.9 lbf ft) Loctite® 243TM Screw, oil pump M6 12 Nm (8.9 lbf ft) Loctite®
243TM Screw, retaining bracket, shaft seal ring, clutch cover
M6 11 Nm (8.1 lbf ft) Loctite® 243TM
Screw, shift drum locating M6 12 Nm (8.9 lbf ft) Loctite® 243TM Screw, starter motor M6 12 Nm (8.9 lbf ft) – Screw, timing
chain tensioner M6 12 Nm (8.9 lbf ft) – Screw, timing chain tensioning rail M6 12 Nm (8.9 lbf ft) Loctite® 243TM Screw,
unlocking of timing chain tensioner
M6 10 Nm (7.4 lbf ft) –
Screw, valve cover M6 12 Nm (8.9 lbf ft) – Screw, water pump cover M6 12 Nm (8.9 lbf ft) – Nut, exhaust flange M8 22 Nm
(16.2 lbf ft) – Screw, balancer shaft gear M8 20 Nm (14.8 lbf ft) Loctite® 243TM Screw, return spring, quick shifter M8 12 Nm
(8.9 lbf ft) Loctite® 243TM Stud, exhaust flange M8 22 Nm (16.2 lbf ft) – Screw, conrod bearing M8x1 34 Nm (25.1 lbf ft) –

21 TECHNICAL DATA
159
Oil pressure sensor M10 14 Nm (10.3 lbf ft) – Rotor screw M10 75 Nm (55.3 lbf ft) Loctite® 243TM Screw, camshaft drive
sprocket M10 32 Nm (23.6 lbf ft) Loctite® 243TM Screw, cylinder head M10 1st stage
30 Nm (22.1 lbf ft) 2nd stage 60 Nm (44.3 lbf ft)
Thread is oiled, head flat is greased
Water temperature sensor M10 14 Nm (10.3 lbf ft) – Spark plug M12 15 Nm (11.1 lbf ft) – Nut, timing chain sprocket M14 55
Nm (40.6 lbf ft) Loctite® 243TM Nut, inner clutch hub M16LHx1.5 120 Nm (88.5 lbf ft) Loctite® 243TM Nut, primary
gear/timing chain sprocket
M16x1.5 120 Nm (88.5 lbf ft) Loctite® 243TM
Screw plug, alternator cover M18x1.5 10 Nm (7.4 lbf ft) – Oil drain plug M24x1.5 15 Nm (11.1 lbf ft) – Nut, drive wheel for
balancer shaft M28 60 Nm (44.3 lbf ft) –
21.4 Capacities
21.4.1 Engine oil
21.4.2 Coolant
Coolant 1.1 l (1.2 qt.) Coolant ( p. 186)
21.4.3 Fuel
Total fuel tank capacity, approx.
11 l (2.9 US gal) Super unleaded (ROZ 95/RON 95/PON 91) ( p. 186)
Fuel reserve, approx. 1.5 l (1.6 qt.)
21.5 Chassis
Frame Lattice frame of steel tubes, powder-coated Fork WP Suspension Shock absorber WP Suspension Brake system
Front Disc brake with four-pot brake caliper Rear Disc brake with single-piston brake caliper, floating Suspension travel
Front 150 mm (5.91 in) Rear 150 mm (5.91 in) Brake discs - diameter
Front 300 mm (11.81 in) Rear 230 mm (9.06 in) Brake discs - wear limit
Front 3.6 mm (0.142 in) Rear 3.6 mm (0.142 in) Tire air pressure, solo
Front 2.0 bar (29 psi) Rear 2.0 bar (29 psi) Tire air pressure with passenger/full payload
Front 2.0 bar (29 psi)

21 TECHNICAL DATA
160
Rear 2.2 bar (32 psi) Secondary ratio 15:45 Chain 5/8 x 1/4” (520) O-ring Steering head angle 65° Wheelbase 1,367±15 mm
(53.82±0.59 in) Seat height, unloaded 800 mm (31.5 in) Ground clearance, unloaded 172 mm (6.77 in) Weight without fuel,
approx. 142 kg (313 lb.)
21.6 Electrical system

Battery FTZ-9 Battery voltage: 12 V
Nominal capacity: 8 Ah Maintenance-free Fuse 75011088010 10 A Fuse 75011088015 15 A Fuse 75011088030 30 A Headlight
H4/socket P43t 12 V
60/55 W Parking light
W5W/socket W2.1x9.5d 12 V
5 W Instrument lights and
indicator lamps LED Turn signal LED Brake/tail light LED License plate lamp LED
21.7 Tires
Front tires Rear tires 110/70 R 17 M/C 54S TL MRF revz FC
150/60 R 17 M/C 66S TL MRF revz C Additional information is available in the Service section under: http://www.ktm.com
21.8 Fork
Fork part number 90101000044
Fork WP Suspension Fork length 736 mm (28.98 in)
Fork oil 450 ml (15.21 fl. oz.) Fork oil (SAE 4) (48601166S1) ( p. 186)
21.9 Shock absorber

Shock absorber part number 90204010000 Shock absorber WP Suspension Spring preload
Standard 3 clicks Full payload 10 clicks Static sag 15 mm (0.59 in) Riding sag 50... 55 mm (1.97... 2.17 in) Fitted length 300 mm
(11.81 in)

21 TECHNICAL DATA
161
21.10 Chassis tightening torques

Exhaust clamp - 10 Nm (7.4 lbf ft) – Screw, chain guard EJOT PT® 4 Nm (3 lbf ft) – Screw, headlight EJOT PT® 4 Nm (3 lbf
ft) – Remaining screws, chassis M4 4 Nm (3 lbf ft) – Screw, EFI control unit M4 4 Nm (3 lbf ft) – Screw, trim, subframe, bottom
M4 2 Nm (1.5 lbf ft) – Remaining nuts, chassis M5 3 Nm (2.2 lbf ft) – Remaining screws, chassis M5 5 Nm (3.7 lbf ft) – Screw,
brake fluid reservoir of rear brake
M5 6 Nm (4.4 lbf ft) Loctite® 243TM
Screw, fuel pump M5 5 Nm (3.7 lbf ft) – Screw, fuel tank closure flange M5 3 Nm (2.2 lbf ft) – Screw, fuel tank cover M5 4 Nm
(3 lbf ft) – Screw, fuel tank trim M5 5 Nm (3.7 lbf ft) – Screw, license plate holder M5 11 Nm (8.1 lbf ft) – Screw, rollover
sensor M5 6 Nm (4.4 lbf ft) Loctite® 243TM Screw, side stand switch M5 5 Nm (3.7 lbf ft) Loctite® 243TM Screw, spoiler M5
5 Nm (3.7 lbf ft) – Screw, subframe cover, bottom M5 5 Nm (3.7 lbf ft) Loctite® 243TM Screw, windshield M5 3 Nm (2.2 lbf ft)
– Nut, foot brake lever adjustment M6 10 Nm (7.4 lbf ft) – Nut, radiator M6 5 Nm (3.7 lbf ft) – Remaining nuts, chassis M6 15
Nm (11.1 lbf ft) – Remaining screws, chassis M6 10 Nm (7.4 lbf ft) – Screw, air filter box M6 6 Nm (4.4 lbf ft) – Screw, bottom
of rear part M6 11 Nm (8.1 lbf ft) – Screw, brake fluid reservoir of rear brake
M6 9 Nm (6.6 lbf ft) –
Screw, cable holder, side stand switch M6 9 Nm (6.6 lbf ft) Loctite® 243TM Screw, chain sliding guard M6 9 Nm (6.6 lbf ft)
Loctite® 243TM Screw, compensating tank M6 11 Nm (8.1 lbf ft) – Screw, foot brake cylinder M6 9 Nm (6.6 lbf ft) Loctite®
243TM Screw, front fender M6 11 Nm (8.1 lbf ft) – Screw, front seat fixing M6 5 Nm (3.7 lbf ft) – Screw, fuel tank M6 11 Nm
(8.1 lbf ft) – Screw, headlight holder M6 11 Nm (8.1 lbf ft) – Screw, headlight mask M6 11 Nm (8.1 lbf ft) – Screw, ignition coil
M6 9 Nm (6.6 lbf ft) – Screw, license plate holder M6 14 Nm (10.3 lbf ft) – Screw, magnetic holder on side stand M6 5 Nm (3.7
lbf ft) Loctite® 243TM Screw, main silencer M6 11 Nm (8.1 lbf ft) – Screw, radiator bracket M6 6 Nm (4.4 lbf ft) – Screw,
radiator holder M6 9 Nm (6.6 lbf ft) – Screw, rear splash protector M6 9 Nm (6.6 lbf ft) – Screw, rollover sensor holder M6 11
Nm (8.1 lbf ft) – Screw, seat M6 11 Nm (8.1 lbf ft) – Screw, shift activation M6 11 Nm (8.1 lbf ft) Loctite® 243TM Screw,
voltage regulator M6 10 Nm (7.4 lbf ft) – Screw, voltage regulator holder M6 15 Nm (11.1 lbf ft) – Remaining nuts, chassis M8
30 Nm (22.1 lbf ft) – Remaining screws, chassis M8 25 Nm (18.4 lbf ft) –

21 TECHNICAL DATA
162
Screw, bottom triple clamp M8 15 Nm (11.1 lbf ft) – Screw, engine bearer on frame M8 30 Nm (22.1 lbf ft) – Screw, foot brake
lever M8 15 Nm (11.1 lbf ft) Loctite® 243TM Screw, fork stub M8 15 Nm (11.1 lbf ft) – Screw, front brake disc M8 30 Nm
(22.1 lbf ft) Loctite® 243TM Screw, front wheel spindle M8 30 Nm (22.1 lbf ft) – Screw, handlebar clamp M8 21 Nm (15.5 lbf
ft) – Screw, handrail M8 31 Nm (22.9 lbf ft) – Screw, horn M8 6 Nm (4.4 lbf ft) – Screw, main silencer M8 23 Nm (17 lbf ft) –
Screw, rear brake disc M8 30 Nm (22.1 lbf ft) Loctite® 243TM Screw, rear footrest bracket M8 26 Nm (19.2 lbf ft) Loctite®
243TM Screw, shift lever M8 15 Nm (11.1 lbf ft) Loctite® 243TM Screw, top triple clamp M8 11 Nm (8.1 lbf ft) – Screw, front
brake caliper M8x1 27 Nm (19.9 lbf ft) Loctite® 243TM Fitting side stand M10 34 Nm (25.1 lbf ft) – Fitting, engine mounting
bracket M10 55 Nm (40.6 lbf ft) – Nut, mirror M10 16 Nm (11.8 lbf ft) – Remaining nuts, chassis M10 50 Nm (36.9 lbf ft) –
Remaining screws, chassis M10 45 Nm (33.2 lbf ft) – Fitting, bottom shock absorber M10x1.25 45 Nm (33.2 lbf ft) – Fitting,
handlebar support M10x1.25 21 Nm (15.5 lbf ft) – Nut, rear sprocket screw M10x1.25 32 Nm (23.6 lbf ft) – Nut, turn signal
M10x1.25 6 Nm (4.4 lbf ft) – Screw, front footrest bracket M10x1.25 46 Nm (33.9 lbf ft) – Screw, side stand bracket M10x1.25
25 Nm (18.4 lbf ft) Loctite® 243TM Screw, top shock absorber M10x1.25 50 Nm (36.9 lbf ft) – Nut, rear wheel spindle
M14x1.5 90 Nm (66.4 lbf ft) – Nut, swingarm pivot M14x1.5 140 Nm (103.3 lbf ft) – Screw, top steering head M16x1.5 52 Nm
(38.4 lbf ft) – Lambda sensor M18x1.5 40... 60 Nm (29.5...
44.3 lbf ft)
Lubricant (T152)
( p. 188) Nut,
steering head M30x1 5 Nm (3.7 lbf ft) –

22 CLEANING/PROTECTIVE TREATMENT
163
22.1 Cleaning the motorcycle

Note Material damage Damage and destruction of components by high-pressure cleaning equipment.
– When cleaning the vehicle with a pressure cleaner, do not point the water jet directly onto electrical components, connectors,
cables, bearings, etc. Maintain a minimum distance of 60 cm between the nozzle of the pressure cleaner and the component.
Excessive pressure can cause malfunctions or destroy these parts.
Info If you clean the motorcycle regularly, its value and appearance will be maintained over a long period. Avoid direct sunshine
on the motorcycle during cleaning.
401061-01
– Seal the exhaust system to keep water out. – First remove coarse dirt particles with a gentle spray of water. – Spray very dirty
areas with a normal motorcycle cleaner and then clean with a
paintbrush.
Motorcycle cleaner ( p. 188)
Info Use warm water containing normal motorcycle cleaner and a soft sponge. Never apply motorcycle cleaner to a dry vehicle;
always rinse the vehicle with water first. If the vehicle was operated in road salt, clean it with cold water. Warm water would
enhance the corrosive effects of salt.
– After rinsing the motorcycle with a gentle spray of water, allow it to dry thoroughly. – Remove the closure of the exhaust
system.
Warning Danger of accidents Reduced braking efficiency due to a wet or dirty brake system. – Clean or dry a dirty or wet brake
system by riding and braking gently.
– After cleaning, ride the vehicle a short distance until the engine warms up.
Info The heat produced causes water at inaccessible locations in the engine and on the brake system to evaporate.
– Push back the sleeves of the handlebar controls to allow any water that has pene-
trated to evaporate. – After the motorcycle has cooled off, lubricate all moving parts and bearings. – Clean the chain. ( p. 59)
– Treat bare metal parts (except for brake discs and exhaust system) with
anti-corrosion materials.
Cleaning and preserving materials for metal, rubber and plastic ( p. 187)
– Treat all painted parts with a mild paint polish.
High-luster polish for paint ( p. 187)
– Treat all plastic parts and powder-coated parts with a mild cleaning and care prod-
uct.
Paint cleaner and polish for high-gloss and matte finishes, bare metal and plastic surfaces ( p. 188)
– Oil the ignition/steering lock.
Universal oil spray ( p. 188)

22 CLEANING/PROTECTIVE TREATMENT
164
22.2 Checks and maintenance steps for winter operation

Info If the motorcycle is used in the winter, salt can be expected on the roads. Precautions need to be taken against road salt
corrosion. If the vehicle was operated in road salt, clean it with cold water after riding. Warm water would enhance the
corrosive effects of salt.
401060-01
– Clean the motorcycle. ( p. 163) – Clean the brakes.
Info After EVERY trip on salted roads, thoroughly wash the brake calipers and brake linings with cold water and dry carefully.
This should be done after the parts are cooled down and while they are installed. After riding on salted roads, thoroughly wash
the motorcycle with cold water and dry it well.
– Treat the engine, swingarm, and all other bright and zinc-plated parts (except for
the brake discs) with a wax-based corrosion inhibitor.
Info Corrosion inhibitor is not permitted to come in contact with the brake discs as this would greatly reduce the braking force.
– Clean the chain. ( p. 59)

23 STORAGE
165
23.1 Storage
Info If you want to garage the motorcycle for a longer period, take the following steps. Before storing the motorcycle, check all
parts for function and wear. If service, repairs or replacements are necessary, you should do this during the storage period (less
workshop overload). In this way, you can avoid long workshop waiting times at the start of the new season.
401058-01
– When refueling for the last time before taking the motorcycle out of service, add
fuel additive.
Fuel additive ( p. 187)
– Refuel. – Clean the motorcycle. ( p. 163) – Change the engine oil and oil filter, clean the oil screen. ( p. 154) – Check the
antifreeze and coolant level. ( p. 149) – Check the tire air pressure. ( p. 52) – Remove the battery. ( p. 61) – Recharge the battery.
( p. 62)
Guideline
Storage temperature of battery without direct sunlight
0... 35 °C (32... 95 °F)
– Store the vehicle in a dry location that is not subject to large fluctuations in tem-
perature.
Info KTM recommends jacking up the motorcycle.
– Raise the motorcycle with the rear wheel stand. ( p. 9) – Raise the motorcycle with the front wheel stand. ( p. 9) – Cover the
motorcycle with a tarp or similar cover that is permeable to air.
Info Do not use non-porous materials since they prevent humidity from escaping, thus causing corrosion. Avoid running the
engine for a short time only. Since the engine cannot warm up properly, the water vapor produced during combustion condenses
and causes valves and exhaust system to rust.
23.2 Preparing for use after storage

401059-01
– Take the motorcycle off of the front wheel stand. ( p. 10) – Take the motorcycle off of the rear wheel stand. ( p. 9) – Recharge
the battery. ( p. 62) – Install the battery. ( p. 61) – Set the clock. ( p. 76) – Perform checks and maintenance steps when preparing
for use. – Take a test ride.

24 SERVICE SCHEDULE
166
24.1 Service schedule

Every 15,000 km (9,321 mi) or every 2 years
Every 7,500 km (4,660 mi) or annually
Once after 1,000 km (621.4
mi) Check the functioning of the electrical equipment. ○ ● Read out the fault memory using the KTM diagnostics tool. ○ ●
Change the engine oil and oil filter, clean the oil screen. ( p. 154) ○ ● Check the front brake linings. ( p. 65) ○ ● Check the
rear brake linings. ( p. 69) ○ ● Check the brake discs. ( p. 53) ○ ● Check the brake lines for damage and leakage. ○ ●
Check the rear brake fluid level. ( p. 72) ○ ● Check the shock absorber and fork for leaks. ○ ● Check the swingarm bearing.
● Check the wheel bearing for play. ● Check the tire condition. ( p. 52) ○ ● Check the tire air pressure. ( p. 52) ○ ● Check
the chain, rear sprocket, and engine sprocket. ( p. 58) ● Check the chain tension. ( p. 57) ○ ● Grease all moving parts (e.g. side
stand, hand lever, chain, ...) and check for smooth operation. ○ ● Clean the dust boots of the fork legs. ( p. 14) ● Check the
brake fluid level of the front brake. ( p. 67) ○ ● Check the steering head bearing play. ( p. 26) ○ ● Change the spark plugs. ●
Check the valve clearance. ○ ● Check all hoses (e.g. fuel, cooling, bleeder, drainage, etc.) and sleeves for cracking, leaks, and
correct routing. ○ ● Check the antifreeze and coolant level. ( p. 149) ○ ● Check the cables for damage and routing without
sharp bends. ● Check that the throttle cables are undamaged, routed without sharp bends, and set correctly. ○ ● Change the air
filter. Clean the air filter box. ● Check the screws and nuts for tightness. ○ ● Change the front brake fluid. ( p. 68) ● Change
the rear brake fluid. ( p. 73) ● Check the headlight setting. ( p. 76) ○ ● Check that the radiator fan is functioning properly. ○
● Final check: Check the vehicle for roadworthiness and take a test ride. ○ ● Read out the fault memory using the KTM
diagnostics tool after a test ride. ○ ● Make the service entry in KTM DEALER.NET and in the service booklet. ○ ●
○ One-time interval
● Periodic interval

167

25 WIRING DIAGRAM
168
25.1 Page 1 of 9
bl
2
2
bl
1
rd
rd
wh-gn
3
wh-gn
13
14
bl-ye
ye-rd
ye-rd
1
rd
rd 1 1 30A 10
10
wh-bl
ye-bu
1
1
ye-bu
1
1 2
2
wh-gn
4 4
3
4 4
ye-rd
wh-or
3
3
4
4
ye-rd
bu-gr
5
5
2 2 rd-gr wh-or
2
2 1
1
gn-rd
wh-br
3
3 4 4
wh-or
2
2 1
bl-ye
3
3
4 4
gn-rd
gn-rd
bu-gr
wh-or
13 13 15A 4 4
bu-gr
13
wh-or
14
308201-01 1 gn-rd
gn-rd
4 4 46 46 bu-gr
wh-or

25 WIRING DIAGRAM
169
Components: A11 EFI control unit A50 Alarm system (optional) A60 Vehicle control unit F1 Fuse F4 Fuse G10 Battery K11
Start auxiliary relay 1 K17 Start auxiliary relay 2 K18 Start auxiliary relay 3 K19 Starter relay M10 Starter motor S23 Emergency
OFF switch, electric starter button

25 WIRING DIAGRAM
170
25.2 Page 2 of 9
15A wh-rd
12
12 3
3
wh-bl
wh-rd
2
2 1
1
bu-gn
bu-gn 2 2 wh-rd
3
3
4 4
wh-br
wh-br
wh-br
2
2 1
1 wh-bu
wh-bu 19 19 wh-rd
4
4 3 bl-ye 1
2 bu-or
wh-bl
wh-br
gn-pk
gn-pk
or
ye-gr
ye-gr
wh-bl
bu-br
15
bu-br
bu-br
18
18 10A 9 9 bu-br
ye-rd
1
1
3
2 1
3 4 1
2 bu-or 1 2 or
14
14 15A 5 5
2 1 49 49 3 4
bl-ye
1 2 wh-bl
1
1
2 2
br
15 15A 6 6
12
12
ye-rd
bl-ye
308202-01

25 WIRING DIAGRAM
171
Components: A11 EFI control unit A50 Alarm system (optional) F3 Fuse F5 Fuse F6 Fuse F9 Fuse K30 Power relay K40 Fuel
pump relay K50 Radiator fan relay M13 Fuel pump M14 Radiator fan S11 Ignition/steering lock X293 Connector for accessory
ground ACC 2 (not assigned) X294 Connector for accessory plug terminal 15 ACC 2 (not assigned)

25 WIRING DIAGRAM
172
25.3 Page 3 of 9
15A wh
11
11 2 2
wh-bl
wh-bl wh-bl
wh
1 1 wh 8
bl-ye
pu
pu
ye-bu bu-gn
bu ye bl-ye
bl-ye
1
1 2
2
HC/3
HB/3
wh
wh
8
7
7
2
2 1 1 4 4
1 35 2
bl
ye-bu bu-gn
ye
35
2 3 6
47 47 wh
1
wh
bu
36 36 48 48 308203-01

25 WIRING DIAGRAM
173
Components: A11 EFI control unit A50 Alarm system (optional) B36 Alarm system switch (optional) F2 Fuse G20 Alternator
P10 Combination instrument T20 Voltage regulator X295 Diagnostics connector

25 WIRING DIAGRAM
174
25.4 Page 4 of 9
5 1
1 5 2 2
2
6 6 7
1 4
3 4
wh-bl
bl-rd
bu-rd
53 53
2 4 1
3 wh-bl wh-br
wh-br bu-rd
14 14
3
bl-gn
bl-rd
32 32 bu-rd
308204-01
wh-br
43 bu-rd
2 4
ye-bu ye-bu
43
wh-br
1
bl-gn
3
3 1
1
bl-gn ye-gn
31 31 ye-gn 10 10 2
bl-ye
bl-ye
42
42
4 2
2
3
3 1
1
bu-rd br-gn
7 br-gn
23 23 bl-ye
2 bl-ye
3
3
1
pk
pk
bl-ye
4
4
bu-rd
1 3
wh-rd gn
wh-rd gn 2 1
22 22 3
24 24 bl-ye
3 4 gn-rd
gn-rd
11 11
gn-rd
4 4 2 4

25 WIRING DIAGRAM
175
Components: A11 EFI control unit B10 Throttle position sensor circuit A B26 Rollover sensor B30 Side stand switch B32 Fuel
tank sensor B45 Temperature and manifold absolute pressure sensor B51 Lambda sensor (cylinder 1) M51 Injection valve
(cylinder 1) P10 Combination instrument

25 WIRING DIAGRAM
176
25.5 Page 5 of 9
55 1
1 55
2
2
6
bl
bl
bl-bu
wh-ye
bl-ye
wh-or
wh-or
1
1 2
2
ye-gn gn-rd 3
3 4
4
wh-gr
ye-gn gn-rd 37 37 38 38 wh-gr bl-bu 25 wh-rd
wh-rd
39 39 ye-gn 40
wh-ye
wh-gn
wh-ye
1
2 ye-gn
308205-01 26 26 25 1
1 4 2
2
bl-ye
bl-ye
27 27 1
1 2 2 bu-pk
bu-pk 30 30 wh-ye
lbu
28 28 9 N
3
lbu
1st 6th 4th 2nd 5th 3rd
ye
14
1
lbu
3 ye-gn
40 44 44 45 45
13
2
6 13 3
lbu
9
1
1 2
2 3
wh-bu bl
6
6
4
14 3
gn
wh-bu bl gn
5
5 4
4
5
4 5 6
rd wh
rd wh
3
3 2
2 ye
1
1
wh-gn
2
2 3 6

25 WIRING DIAGRAM
177
Components: A11 EFI control unit A60 Vehicle control unit B21 Coolant temperature sensor (cylinder 1) B34 Gear position
sensor B37 Ignition pulse generator B38 Clutch switch M65 Idle speed actuator P10 Combination instrument R51 Ignition coil
(cylinder 1)

25 WIRING DIAGRAM
178
25.6 Page 6 of 9
2 br
br
2 br
br
1
2 1 1
bl
br
ye-rd bl-rd
1 1 2 2 2 1 3 1 2
2
br
4 4 bl-ye
3 3
6 6
bl
1
1
wh-br
ye-rd bl-rd
4
4 5
5 2
2
1
1
pu
pu
1
1
br
bl-rd
bl-rd
3 3
bl-rd ye-rd br
1 1 2
2 4 4
bl-rd ye-rd br
bl-ye
1
1 2 2 bl-ye
1
1
2
2 3
3
bl-ye
3
3
bl-ye
bl-ye
bl-ye
1 6
1 6
wh-br
br
2
2
1 1 bu
FG/1 FG/1
br
2
bu
br
1
bl-ye
bl-ye
br
3
1
bl-ye bu
308206-01

25 WIRING DIAGRAM
179
Components: A60 Vehicle control unit B76 Brake light switch, front B77 Brake light switch, rear E13 Low beam, high beam E60
License plate lamp P10 Combination instrument P15 Horn P35 Parking light P36 Brake/tail light S23 Emergency OFF switch,
electric starter button S24 Light switch, horn button, high beam flasher button, turn signal switch

25 WIRING DIAGRAM
180
25.7 Page 7 of 9
2 or
gr
bu-pk
pk-br
2
2
2
4
4 3
gn
9
1
2 2
gn
1
2 2 gn
6
1 2 1
2 bu-pk
or
bl-ye
bl-ye
3
2
gr
gr
10
10
gn
gr
9
1 bl-ye
bl-ye
1
gn
6
1
2 gr
7
7
1
bl-ye
bl-ye bl-ye
1 1 2 2
bl-ye 18 18 pk-br
16
16 308207-01

25 WIRING DIAGRAM
181
Components: A50 Alarm system (optional) A60 Vehicle control unit B35 Oil pressure sensor P10 Combination instrument P41
Turn signal, front left P42 Turn signal, front right P45 Turn signal, rear left P46 Turn signal, rear right S24 Light switch, horn
button, high beam flasher button, turn signal switch

25 WIRING DIAGRAM
182
25.8 Page 8 of 9
5 bl-ye
bl-ye
5
bl-ye
bl-ye
5
5
bl
bl-ye
bl-ye
bl
bl-ye bl-ye
bl-ye bl-ye
3
3
bl-ye
bl-ye
6
6
wh-gr
11
11
wh-gr
2
2
bl-ye
10 10
bl
8 8
bl-ye
bl-pu
19 19
wh-ye
12
12
br-rd
15
15
bu-or
5
5
bl-ye
bl-ye
21
21
bl-ye
bu-or
1
1
br-rd
3
3
bl-ye
wh-ye
8
8
bl-pu
20
20
bl-ye
bl-ye
50 50 51
51 52
52
308208-01

25 WIRING DIAGRAM
183
Components: A11 EFI control unit A50 Alarm system (optional) A60 Vehicle control unit P10 Combination instrument

25 WIRING DIAGRAM
184
25.9 Page 9 of 9
10A gn-gr 16
16 7 7 rd-gr
ye-gr
9
9
ye-gr
17
17 10A 8 8 rd-gr
ye-gr
ye-gr wh-bl
11 11 17 17 wh-br
20 20 wh-bu 6 6
wh-bu wh-br wh-bl
8
8 15
15 17
17
bu ye
2
2 11
11
bl-ye bl-ye
bl-ye bl-ye
1
1 10
10
wh-rd
1
1 15A 2
2
wh-bu
wh-bu
9
9
gn-gr
gn-gr
4
4
rd
3
3 25A 4
4
wh-bl
wh-bl
18
18
1
1
bu-pk
bu-pk
3 3
2
2
wh-rd
wh-rd
12 12
1 1
bl-bu
bl-bu
14 14
2
2
wh-rd
wh-rd
13 13
308209-01

25 WIRING DIAGRAM
185
Components: A11 EFI control unit A30 ABS control unit A60 Vehicle control unit B70 Wheel speed sensor, front B71 Wheel
speed sensor, rear F7 Fuse F8 Fuse F21 ABS fuse F22 ABS fuse P10 Combination instrument
Cable colors: bl Black br Brown bu Blue gn Green gr Gray lbu Light blue or Orange pk Pink pu Violet rd Red wh White ye
Yellow

26 SUBSTANCES
186
Brake fluid DOT 4 / DOT 5.1

According to – DOT Guideline – Use only brake fluid that complies with the specified standard (see specifications on the
container) and that possesses the corre-
sponding properties. KTM recommends Castrol and Motorex® products. Supplier Castrol – RESPONSE BRAKE
FLUID SUPER DOT 4 Motorex® – Brake Fluid DOT 5.1
Coolant
Guideline – Use only suitable coolant (also in countries with high temperatures). Use of low-quality antifreeze can lead to
corrosion and foam-
ing. KTM recommends Motorex® products. Mixture ratio
Antifreeze protection: −25... −45 °C (−13... −49 °F)
50 % corrosion inhibitor/antifreeze 50 % distilled water
Coolant (mixed ready to use)

Antifreeze −40 °C (−40 °F)
Supplier Motorex® – COOLANT G48
Engine oil (SAE 15W/50)

According to – JASO T903 MA ( p. 198) – SAE ( p. 198) (SAE 15W/50) Guideline – Use only engine oils that comply with the
specified standards (see specifications on the container) and that possess the corre-
sponding properties. KTM recommends Motorex® products.
Partially synthetic engine oil
Supplier Motorex® – Formula 4T
Fork oil (SAE 4) (48601166S1)

According to – SAE ( p. 198) (SAE 4) Guideline – Use only oils that comply with the specified standards (see specifications on
the container) and that possess the corresponding
properties.
Super unleaded (ROZ 95/RON 95/PON 91)

According to – DIN EN 228 (ROZ 95/RON 95/PON 91) Guideline – Only use unleaded super fuel that matches or is equivalent
to the specified fuel grade. – Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use.
Info Do not use fuel containing methanol (e. g. M15, M85, M100) or more than 10 % ethanol (e. g. E15, E25, E85, E100).

27 AUXILIARY SUBSTANCES
187
Chain cleaner
Guideline – KTM recommends Motorex® products. Supplier Motorex® – Chain Clean
Chain lube for road use

Guideline – KTM recommends Motorex® products. Supplier Motorex® – Chainlube Road
Cleaning and preserving materials for metal, rubber and plastic

Guideline – KTM recommends Motorex® products. Supplier Motorex® – Protect & Shine
Fuel additive
Guideline – KTM recommends Motorex® products. Supplier Motorex® – Fuel Stabilizer
High viscosity grease

Guideline – KTM recommends SKF® products. Supplier SKF® – LGHB 2
High-luster polish for paint

Guideline – KTM recommends Motorex® products. Supplier Motorex® – Moto Polish
Long-life grease
Guideline – KTM recommends Motorex® products. Supplier Motorex® – Bike Grease 2000
Lubricant (T511)
Guideline – KTM recommends Lubcon® products. Supplier Lubcon® – Turmsilon® GTI 300 P

27 AUXILIARY SUBSTANCES
188
Lubricant (T152)
Guideline – KTM recommends Bel-Ray® products. Supplier Bel-Ray® – Molylube® Anti-Seize
Motorcycle cleaner
Guideline – KTM recommends Motorex® products. Supplier Motorex® – Moto Clean 900
Paint cleaner and polish for high-gloss and matte finishes, bare metal and plastic surfaces
Guideline – KTM recommends Motorex® products. Supplier Motorex® – Clean & Polish
Universal oil spray

Guideline – KTM recommends Motorex® products. Supplier Motorex® – Joker 440 Synthetic

28 SPECIAL TOOLS
189
Bleeder cover
Art. no.: 00029013000
Bleeding device
Art. no.: 00029013100
Bleed syringe
400058-01
Art. no.: 50329050000
Circlip pliers reverse

400059-01
Art. no.: 51012011000
Clutch holder
400289-01
Art. no.: 51129003000
201490-10
201491-10

28 SPECIAL TOOLS
190
Valve spring compressor

400101-01
Art. no.: 59029019000
Feeler gauge
25
20
Art. no.: 59029041100
3
5 3
0
15
1
2
1
0
5
400110-01
Plastigauge measuring strips

400122-01
Art. no.: 60029012000
Piston ring mounting tool

400123-01
Art. no.: 60029015000
Adapter
C00194-01
Art. no.: 61029055130

28 SPECIAL TOOLS
191
Rear wheel stand

Art. no.: 61029055400
Front wheel stand

Art. no.: 61029055500
Testing hose
Art. no.: 61029093000
Pressure testing tool

400149-01
Art. no.: 61029094000
Adapter
B00756-01
B00757-01
500077-01
201314-01
Art. no.: 61029955620

28 SPECIAL TOOLS
192
Engine assembly stand

200306-01
Art. no.: 61229001000
Engine blocking screw

200312-01
Art. no.: 61229015000
Work stand
400151-01
Art. no.: 62529055000
Floor jack attachment

400184-01
Art. no.: 75029055000
Oil pressure adapter

400169-01
Art. no.: 75029094000

28 SPECIAL TOOLS
193
Limit plug gauge

400104-01
Art. no.: 77029026000
Insert for valve spring lever

Art. no.: 77029041100
Spark plug wrench

Art. no.: 77229172000
Insert for piston pin retainer

400160-01
Art. no.: 77329030100
Engine fixing arm

303272-10
304549-10
304419-10
Art. no.: 90129002050

28 SPECIAL TOOLS
194
Engine fixing arm

Art. no.: 90129002060
Mounting sleeve
201612-01
Art. no.: 90129005000
Pressure screw for crankshaft

Art. no.: 90129020000
Castle nut wrench; 1⁄2" drive

Art. no.: 90129021000

304418-10
304527-10
304430-10
304469-10
Art. no.: 90129022000

28 SPECIAL TOOLS
195
Mounting sleeve
Art. no.: 90129043000
Case separating tool

Art. no.: 90129048100

Art. no.: 90129050000

Art. no.: 90129050100
Key for steering head bearing

304541-10
308111-01
305037-10
305037-10
304951-10
Art. no.: 90129051000

28 SPECIAL TOOLS
196
Disassembly tool, balancer shaft bearing

Art. no.: 90129056000
Puller for rotor

Art. no.: 90229009000
Hook wrench
301085-01
Art. no.: T106S
Spring compressor
304565-10
308102-01
201648-10
Art. no.: T14050S

28 SPECIAL TOOLS
197
Mounting tool
Art. no.: T528S
Clamping stand
200634-10
200638-10
Art. no.: T612S

29 STANDARDS
198
JASO T903 MA

Different technical development directions required a new specification for 4-stroke motorcycles – the JASO T903 MA Standard.
Ear- lier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle
specification. Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are
in the fore- ground for motorcycle engines. In most motorcycles, the gearbox and the clutch are lubricated with the same oil as
the engine. The JASO MA Standard meets these special requirements.
SAE
The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to
their viscosity. The viscosity describes only one property of oil and says nothing about quality.

INDEX
199
INDEX
A Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Air filter
fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Alternator
stator winding, checking . . . . . . . . . . . . . . . . . . . . . 156
Antifreeze
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Assembling the engine
alternator cover, installing . . . . . . . . . . . . . . . . . . . . 137 balancer shaft drive wheel, installing . . . . . . . . . . . . . 135 balancer shaft,
installing . . . . . . . . . . . . . . . . . . . . . 126 camshafts, installing . . . . . . . . . . . . . . . . . . . . . . . . 141 chain securing guide, installing . .
. . . . . . . . . . . . . . 145 clutch cage, installing . . . . . . . . . . . . . . . . . . . . . . . 132 clutch cover, installing . . . . . . . . . . . . . . . . . . . . . .
143 crankshaft, installing . . . . . . . . . . . . . . . . . . . . . . . . 126 cylinder head, installing . . . . . . . . . . . . . . . . . . . . . 140 gear position
sensor, installing . . . . . . . . . . . . . . . . . 135 locking lever, installing . . . . . . . . . . . . . . . . . . . . . . 129 oil filter, installing . . . . . . . . .
. . . . . . . . . . . . . . . . 129 oil pump, installing . . . . . . . . . . . . . . . . . . . . . . . . . 130 oil screen, installing . . . . . . . . . . . . . . . . . . . . . . .
. 145 piston, installing . . . . . . . . . . . . . . . . . . . . . . . . . . 138 primary gear, installing . . . . . . . . . . . . . . . . . . . . . . 131 removing the
engine from the engine assembly stand . . 146 rotor, installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 shift drum locating,
installing . . . . . . . . . . . . . . . . . . 130 shift drum, installing . . . . . . . . . . . . . . . . . . . . . . . . 127 shift forks, installing . . . . . . . . . . . . .
. . . . . . . . . . . 127 shift rails, installing . . . . . . . . . . . . . . . . . . . . . . . . 127 shift shaft, installing . . . . . . . . . . . . . . . . . . . . . . . . 130
spacer, installing . . . . . . . . . . . . . . . . . . . . . . . . . . 133 spark plug, installing . . . . . . . . . . . . . . . . . . . . . . . . 144 starter drive,
installing . . . . . . . . . . . . . . . . . . . . . . 136 starter motor, installing . . . . . . . . . . . . . . . . . . . . . . 138 suction pump, installing . . . . . .
. . . . . . . . . . . . . . . 134 timing chain tensioner, installing . . . . . . . . . . . . . . . 141 timing chain, installing . . . . . . . . . . . . . . . . . . . . .
. 138 transmission shafts, installing . . . . . . . . . . . . . . . . . 127 valve clearance, adjusting . . . . . . . . . . . . . . . . . . . . 143 valve
clearance, checking . . . . . . . . . . . . . . . . . . . . 142 valve cover, installing . . . . . . . . . . . . . . . . . . . . . . . 144 water pump cover,
installing . . . . . . . . . . . . . . . . . . 137
Auxiliary substances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B
Battery
connecting minus cable . . . . . . . . . . . . . . . . . . . . . . . 62 disconnecting minus cable . . . . . . . . . . . . . . . . . . . . . 62 installing . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 61 recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 removing . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 61
Brake disc
front brake, changing . . . . . . . . . . . . . . . . . . . . . . . . 54 front brake, removing . . . . . . . . . . . . . . . . . . . . . . . . 54 rear brake,
installing . . . . . . . . . . . . . . . . . . . . . . . . . 56 rear brake, removing . . . . . . . . . . . . . . . . . . . . . . . . . 56
Brake discs
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Brake fluid
front brake, adding . . . . . . . . . . . . . . . . . . . . . . . . . . 67 front brake, changing . . . . . . . . . . . . . . . . . . . . . . . . 68 rear brake, adding .
. . . . . . . . . . . . . . . . . . . . . . . . . 73 rear brake, changing . . . . . . . . . . . . . . . . . . . . . . . . . 73
Brake fluid level
front brake, checking . . . . . . . . . . . . . . . . . . . . . . . . 67 rear brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . 72
Brake linings
front brake, changing . . . . . . . . . . . . . . . . . . . . . . . . 65 front brake, checking . . . . . . . . . . . . . . . . . . . . . . . . 65 rear brake,
changing . . . . . . . . . . . . . . . . . . . . . . . . . 70 rear brake, checking . . . . . . . . . . . . . . . . . . . . . . . . . 69
C
Capacity
coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89, 159 fuel . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 159
Chain
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Chain tension
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Charging voltage
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Chassis number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Clutch cable play
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Clutch lever play
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Coolant
draining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Coolant level
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149-150
Cooling system
filling/bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
D
Disassembling the engine
alternator cover, removing . . . . . . . . . . . . . . . . . . . . . 96 balancer shaft drive wheel, removing . . . . . . . . . . . . . . 98 balancer shaft,
removing . . . . . . . . . . . . . . . . . . . . . 106 camshaft, removing . . . . . . . . . . . . . . . . . . . . . . . . . 93 chain securing guide, removing . .
. . . . . . . . . . . . . . . 90 clutch cage, removing . . . . . . . . . . . . . . . . . . . . . . . 100 clutch cover, removing . . . . . . . . . . . . . . . . . . . . . . .
91 crankshaft, removing . . . . . . . . . . . . . . . . . . . . . . . . 106 cylinder head, removing . . . . . . . . . . . . . . . . . . . . . . . 94 engine oil,
draining . . . . . . . . . . . . . . . . . . . . . . . . . . 90 engine, setting to ignition top dead center . . . . . . . . . . 92 force pump, removing . . . .
. . . . . . . . . . . . . . . . . . . 102 gear position sensor, removing . . . . . . . . . . . . . . . . . . 98 locking lever, removing . . . . . . . . . . . . . . . .
. . . . . . 103 oil filter, removing . . . . . . . . . . . . . . . . . . . . . . . . . 103 piston, removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

INDEX
200
preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 primary gear, removing . . . . . . . . . . . . . . . . . . . . . . 101 rotor, removing . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 97 shift drum locating, removing . . . . . . . . . . . . . . . . . . 103 shift drum, removing . . . . . . . . . . . .
. . . . . . . . . . . . 105 shift forks, removing . . . . . . . . . . . . . . . . . . . . . . . . 106 shift rails, removing . . . . . . . . . . . . . . . . . . . . . . . . 105
shift shaft, removing . . . . . . . . . . . . . . . . . . . . . . . . 103 spacer, removing . . . . . . . . . . . . . . . . . . . . . . . . . . 100 spark plug,
removing . . . . . . . . . . . . . . . . . . . . . . . . . 91 starter drive, removing . . . . . . . . . . . . . . . . . . . . . . . . 97 starter motor, removing . . . .
. . . . . . . . . . . . . . . . . . . 95 suction pump, removing . . . . . . . . . . . . . . . . . . . . . . 99 timing chain tensioner, removing . . . . . . . . . . .
. . . . . 93 timing chain, removing . . . . . . . . . . . . . . . . . . . . . . . 95 transmission shafts, removing . . . . . . . . . . . . . . . . . 106 valve
cover, removing . . . . . . . . . . . . . . . . . . . . . . . . 91 water pump wheel, removing . . . . . . . . . . . . . . . . . . . 96
E
Engine
assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 disassembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 installing . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 85 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 work on individual parts . . . . . . . . . . . . . . .
. . . . . . . 107
Engine - Work on individual parts
balancer shaft bearing, changing . . . . . . . . . . . . . . . 111 clutch, checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 conrod bearing . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 110 countershaft, assembling . . . . . . . . . . . . . . . . . . . . . 122 countershaft, disassembling . . . . . . .
. . . . . . . . . . . . 120 cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 cylinder head, checking . . . . . . . . . . . . . . . . . . . . . . 113
cylinder, checking/measuring . . . . . . . . . . . . . . . . . . 114 electric starter drive, checking . . . . . . . . . . . . . . . . . 125 freewheel,
checking . . . . . . . . . . . . . . . . . . . . . . . . 126 left engine case section . . . . . . . . . . . . . . . . . . . . . . 107 main shaft, assembling . . . . .
. . . . . . . . . . . . . . . . . 121 main shaft, disassembling . . . . . . . . . . . . . . . . . . . . 119 oil pressure regulator valve, checking . . . . . . . .
. . . . 116 oil pump, checking . . . . . . . . . . . . . . . . . . . . . . . . . 115 piston ring end gap, checking . . . . . . . . . . . . . . . . . . 114 piston,
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 piston/cylinder mounting clearance, checking . . . . . . . 115 pistons, measuring . . .
. . . . . . . . . . . . . . . . . . . . . . 115 pivot points of camshafts, checking . . . . . . . . . . . . . . 113 radial play of lower conrod bearing,
checking . . . . . . . 109 right engine case section . . . . . . . . . . . . . . . . . . . . . 108 shaft seal ring of water pump, changing . . . . . . . . .
. . 108 shift mechanism, checking . . . . . . . . . . . . . . . . . . . 118 shift shaft, preassembling . . . . . . . . . . . . . . . . . . . . 119 stator,
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 timing assembly, checking . . . . . . . . . . . . . . . . . . . . 124 transmission, checking .
. . . . . . . . . . . . . . . . . . . . . 120
Engine assembly
left engine case, installing . . . . . . . . . . . . . . . . . . . . 128
Engine disassembly
left engine case, removing . . . . . . . . . . . . . . . . . . . . 104
Engine number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Engine oil
adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Engine oil level
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Engine oil pressure
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Engine sprocket
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Exhaust manifold
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
F Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Filler cap
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Foot brake lever
free travel, adjusting . . . . . . . . . . . . . . . . . . . . . . . . . 72 free travel, checking . . . . . . . . . . . . . . . . . . . . . . . . . 71
Fork legs
assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 dismantling . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . 16 dust boots, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 14 fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 15 Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front fender
Front spoiler
Front wheel
Fuel filter
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Fuel pressure
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Fuel pump
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Fuel tank
Fuel tank cover
Fuse
individual power consumers, changing . . . . . . . . . . . . . 64
H
Headlight adjustment
Headlight bulb
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

INDEX
201
K Key number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Kilometers or miles
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
L
Lower triple clamp
M
Main silencer
Motorcycle
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 raising with the front wheel stand . . . . . . . . . . . . . . . . . 9 raising with the
rear wheel stand . . . . . . . . . . . . . . . . . . 9 raising with the work stand . . . . . . . . . . . . . . . . . . . . 10 removing from work stand . . . .
. . . . . . . . . . . . . . . . . 11 taking off of the front wheel stand . . . . . . . . . . . . . . . . 10 taking off of the rear wheel stand . . . . . . . . . . .
. . . . . . 9
O Oil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Oil filter
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Oil screen
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Operating substances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
P
Parking light bulb
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Passenger seat
mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Play in throttle cable
Preparing for use
after storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
R
Rear hub rubber dampers
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Rear sprocket
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Rear wheel
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
S
Seat
mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Service interval display
reinstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Service schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Shift lever
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Shift speed RPM 1
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Shift speed RPM 2
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Shock absorber
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 spring preload,
adjusting . . . . . . . . . . . . . . . . . . . . . . 30 spring, installing . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 spring, removing . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 31
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 to make checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Steering head bearing play
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
T
Technical data
capacity - coolant . . . . . . . . . . . . . . . . . . . . . . . . . . 159 capacity - engine oil . . . . . . . . . . . . . . . . . . . . . . . . 159 capacity - fuel . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 159 chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 chassis tightening torques . . . . . . . . . . . . .
. . . . . . . 161 electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . 160 engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 engine -
tolerance, wear limits . . . . . . . . . . . . . . . . . 157 engine tightening torques . . . . . . . . . . . . . . . . . . . . 158 fork . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 160 shock absorber . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
160
Time
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Tire air pressure
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tire condition
checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Type label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
W Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Winter operation
checks and maintenance steps . . . . . . . . . . . . . . . . . 164
Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 168-185 page 1 of 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 page 2 of 9 . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 170 page 3 of 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 page 4 of 9 . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 174 page 5 of 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 page 6 of 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 page 7 of
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 page 8 of 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 page 9 of 9 . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 184
Work rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

*3206167en*
3206167en
07/2013
KTM-Sportmotorcycle AG 5230 Mattighofen/Austria http://www.ktm.com
Photo: Mitterbauer/KTM

Duke 390 Repair Manual (Full Version - 204pages)

Uploaded by

Copyright:

Available Formats

Duke 390 Repair Manual (Full Version - 204pages)

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Duke 390 Repair Manual (Full Version - 204pages)

Uploaded by

Copyright:

Available Formats

REPAIR MANUAL 2013

1.1 Symbols used

1.2 Formats used

2.1 Repair Manual

2.2 Safety advice

2.3 Degrees of risk and symbols

2.4 Work rules

3.1 Guarantee, warranty

3.2 Operating and auxiliary substances

3.3 Spare parts, accessories

4.1 Chassis number/type label

4.2 Key number

4.3 Engine number

5.1 Raising the motorcycle with the rear wheel stand

5.2 Taking the motorcycle off of the rear wheel stand

5.3 Raising the motorcycle with the front wheel stand

5.4 Taking the motorcycle off of the front wheel stand

5.5 Raising the motorcycle with the work stand

5.6 Removing the motorcycle from the work stand

5.8 Starting the motorcycle to make checks

6.1 Cleaning the dust boots of the fork legs

6.2 Removing fork legs

6.3 Installing the fork legs

6.4 Disassembling the fork legs

6.5 Checking the fork legs

6.6 Assembling the fork legs

6.7 Removing the lower triple clamp

6.8 Installing the lower triple clamp

6.9 Checking the steering head bearing play

6.10 Adjusting the steering head bearing play

7.1 Checking the play in the throttle cable

7.2 Adjusting the play in the throttle cable

7.3 Checking the clutch lever play

7.4 Adjusting the clutch cable play

8.1 Adjusting the spring preload of the shock absorber

8.2 Removing the shock absorber

8.3 Installing the shock absorber

8.4 Removing the spring

8.5 Installing the spring

9.1 Removing the exhaust manifold

9.2 Installing the exhaust manifold

9.3 Removing the main silencer

9.4 Installing the main silencer

10.1 Removing the air filter

10.2 Installing the air filter

11.1 Opening the filler cap

11.2 Closing the filler cap

11.3 Removing the seat

11.4 Mounting the seat

11.5 Removing the passenger seat

11.6 Mounting the passenger seat

11.7 Removing the fuel tank cover

11.8 Installing the fuel tank cover

11.9 Removing the fuel tank

11.10 Installing the fuel tank

11.11 Removing the front spoiler

11.12 Fitting front spoiler

11.13 Dismounting the front fender

11.14 Installing the front fender

11.15 Checking the fuel pressure