User Manual 1746242

RC 917/TR02
User manual and upgrade instruction
RC917/TR02
Developed for demanding environments Scanreco –

Scanreco´s RC917 / TR02 is built and designed for the toughest and most demanding freedom in a box
of environments. Scanreco can hereby offer the market of crane and machine
operators an extremely easy to use radio remote control retaining speed, Our customers development
precision, and control with the maximum of safety. is our own development. This
Behind the development of the radio transceivers lies the idea enables us to offer:
of providing a product with a high degree of reliability, user-friendliness,
and easy upgrade for cable systems or other data radio applications.  Customer-specific solutions  
The product family includes different transceivers and  Industrial know-how
receivers offering a variety of choice depending on the area of use. These products  Expertise and experience
are based on a modular architecture, which makes them extremely flexible
to customize and adapt according to the customer’s needs.  Innovative capacity
The products – which are in high demand – are mainly mounted on cranes  Nimble organisation
and mobile machines. Our customers are some of the world’s largest and most  Quality
challenging crane and machinery manufacturers. Thousands of cranes and
machines containing Scanreco’s radio products are in use worldwide.  Delivery precision
Our products are deployed everywhere, from truck cranes laying heating  Service
pipes in Stockholm to lifting oil pipelines in Russia and setting in place concrete
sections in Singapore.
www.scanreco.se
RC 917/TR02
How to use the TR02 for user defined multi purpose use
The control and power connector is a standard 2.54mm, 8way pin row.
The functions of the pin s are as follows:
Pin 1: Power supply and signal ground.

Pin 2: Power supply positive terminal.
Accepts 6 to 8VDC. 7.2VDC nominal.
Pin 3: Data input.
Pin 4: Clock input.
Pin 5: Load signal.
Pin 6: Transmit data input. TTL levels.
Pin 7: Transmit/receive input signal. TTL levels. Logic level” 1” on this pin and a RSSI value
below 95dBm will put the module in transit mode. If the RSSI value exceeds 95dBm t
he module enters receive mode. Logic level ”0” will force receive mode.
Pin 8: Received data output. TTL levels.
Pins 3 to 5 make together an SPI port for receiving channel information. Upon start up the
mother board on which the module is mounted will send the channel frequency information
on this port. The module will then enters receive or transmit mode depending on
the status of pin 7. In receive mode the received data will appear asynchronously on pin8.
In transmit mode the asynchronous data on pin 6 will be buffed and fed to modulator
at the same time the output amplifier will be enabled.
The high power version RC917FHH has the output power less than 18dBm when it uses in the
hand held remote control units. The max output power 18dBm of hand held units is programmed
under production at the factory and not possible to change under using by the customer.
There are two antenna connectors, which cannot be used simultaneously.
The antenna types used with the module are presented in the table:
N Antenna type Details Manufacture Part number Connector Gain

1 Internal wire λ/4 8cm length, Scanreco 44374 Soldered 1,5dBi
Stranded Ø1,2mm
conductor,
Ø2,2mm total
2 Internal dipole antenna Total length 16cm, Scanreco 47146 Soldered 2,5dBi
coax cable RG316
3 External λ/4 Helix Total height 12cm Scanreco 47938 RP-SMA 2,8dBi
4 External λ/4 whip Total length 82mm Scanreco 47123/382- TNC 2,6dBi
4179
5 External Right Angle Total length 45 mm Jinchang JC-GSM-000-55- SMA 3,5dBi
λ/4 (or similar: Taoglas TG.22.0112, SMAGSM
Pulse W1900/1902,
Antenna Factor ANT-916-CW)
In case of internal antenna it will be always located at least 2,5 cm from the nearest
host enclosure wall.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Warning
The external antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
transmitter
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment
Typical customer application
as an example
NOTE: if you need assistance or customer

defined application, please contact
Scanreco customer support.
RC 917/TR02
Instruction how to upgrade all Scanreco RC 917 systems,

Note: Pictures show a typical RC 917 system but upgrade
process is valid for all types of RC 917.
1/ Open control pult and locate place

for radio modul*
2/ Install TR02 intended for control pult.

Tighten the supplied screws*, normally 4
Note: Different
t y p e of holders
for wire antenna
is supplied
depending type
of RC 917 system
3/ Reassembly control pult and continue to step 4.
www.scanreco.se
www.scanreco.se
RC 917/TR02
4/ Open the receiver box

locate place for radio module*
5/ Install TR02 intended for

Receiver box and tighten
supplied screws*, normally 4.
6/ Install antenna cabel

in appropriate inlet on box
and connect to TR02 the SMA connector.
7/ Reassembly receiver box,

go to step 8.
8/ Start up system and according

to system manual RC 917,
restart and pair system without
cable control attached.
Note:The SW in RC 917 will automatic

install and identify your upgraded system
for Radio Remote Controller.
This procedure is valid for all RC 917 intended to use with RC 917
10/ Upgrade procedure is done and customer are

now able to enjoy a Radio Control System.
www.scanreco.se

User Manual 1746242

Uploaded by

Copyright:

Available Formats

User Manual 1746242

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User Manual 1746242

Uploaded by

Copyright:

Available Formats

RC 917/TR02

User manual and upgrade instruction

Developed for demanding environments Scanreco –

Pin 1: Power supply and signal ground.

There are two antenna connectors, which cannot be used simultaneously.

N Antenna type Details Manufacture Part number Connector Gain

NOTE: if you need assistance or customer

Instruction how to upgrade all Scanreco RC 917 systems,

1/ Open control pult and locate place

2/ Install TR02 intended for control pult.

3/ Reassembly control pult and continue to step 4.

4/ Open the receiver box

5/ Install TR02 intended for

6/ Install antenna cabel

7/ Reassembly receiver box,

8/ Start up system and according

Note:The SW in RC 917 will automatic

10/ Upgrade procedure is done and customer are

You might also like