Scribd
Upload
82 views3 pages

Bridge Building Mechanics For Student

The document provides guidelines for a bridge building competition. Students will have 2 hours to build a bridge using only provided materials like popsicle sticks, string, and tape. Bridges must be between 400-550mm long, 100-120mm wide, and less than 250mm tall plus deep. Bridges will be tested by applying weights to the center until failure, and ranked based on highest load supported. The group with the highest load will receive a grade of 1.0, while subsequent groups will receive higher grades up to 1.5 for 4th and 5th place.

Uploaded by

Jessa Mae Catabay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
82 views3 pages

Bridge Building Mechanics For Student

The document provides guidelines for a bridge building competition. Students will have 2 hours to build a bridge using only provided materials like popsicle sticks, string, and tape. Bridges must be between 400-550mm long, 100-120mm wide, and less than 250mm tall plus deep. Bridges will be tested by applying weights to the center until failure, and ranked based on highest load supported. The group with the highest load will receive a grade of 1.0, while subsequent groups will receive higher grades up to 1.5 for 4th and 5th place.

Uploaded by

Jessa Mae Catabay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

BRIDGE MODEL

 Create a bridge model based on your team desires.


 A limit of 2 hours will be given for bridge construction.

RESOURCES
 XXXpcs popsicle sticks (exact number will be on the day of event)
 1pc. 1-foot ruler
 1 pair of scissors
 1 ball of yarn (small)
 1 small clear (transparent) tape

BRIDGE SPECIFICATION
 400 mm ≤ Length (L) ≤ 550 mm
(End to end of the bridge laid on a flat surface)
 100 ≤ Width (B) ≤ 120 mm
(Side to side of the bridge laid on a flat surface)
 Height (H) + Depth (D) ≤ 250 mm

NOTE
 RESOURCES will be provided and should be the ONLY materials to be used to
build the bridge.

SAMPLE MODELS:

MODEL 1
MODEL 2

MODEL 3

MODEL 4
Phase I: Screening

 Each bridge must pass the required bridge specifications before it is accepted for the next phase. A bridge
will not be able to proceed for next phase if:
o Did not reach and/or exceeded the required minimum/maximum bridge Length (L)
o Exceeded the maximum bridge Length (L)
o Exceeded the maximum bridge Width (W)
o Exceeded the maximum bridge Height (H) + Depth (D)
o Other materials aside from the RESOURCES given were used.
NOTE:
A group that did not pass the phase 1 will automatically get 0% on project.

Phase II: Bridge Testing

 Weights will be applied at the mid span of the bridge


 If the bridge fails at the nth load applied, the total load applied will be the last placed load before it failed
 The bridge will be considered fail if it is in total destruction state.

NOTE:
In special case that the bridge collapsed right after 1st load is applied, then total applied load will be 0. The group
will automatically get 0% on project.

__________________________________________________________________________________

Grading System

Each group will be ranked according to the highest to lowest total applied load before the destruction of the
bridge.

1st – 1.0 (highest possible grade)

2nd and 3rd- 1.25 (highest possible grade)

4th and 5th - 1.5 (highest possible grade)

NOTE:

In case of a tie, the highest rank they are in will be their grade.

For example

A and B ties at 1st (they are 1st and 2nd), therefore 1st is the highest rank they are in

C and D ties at 2nd (they are 3rd and 4th), therefore 3rd is the highest rank they are in.

E is last (5th)

You might also like