EEDP - Lect 03 - BJT - Bias - 2

Download as pdf or txt
Download as pdf or txt
You are on page 1of 15

Electrical, Electronic and Digital Principles

(EEDP)

Lecture 3
Other BJT Biasing Techniques

‫ باسم ممدوح الحلوانى‬.‫د‬


Approximate Analysis Voltage-divider Bias Exact Analysis

Ri = is the equivalent resistance


between base and ground 0
0

0
Approximate Analysis Voltage-divider Bias Exact Analysis

Electronic Devices and Circuit Theory 11th Ed, Boylstd


Approximate Analysis Voltage-divider Bias Exact Analysis

0 0

0 0

The larger the level of Ri compared to R2 , the closer is the approximate to the exact
Approximate Analysis Voltage-divider Bias Exact Analysis
The larger the level of Ri compared to R2 ,
the closer is the approximate to the exact

 The results reveal the difference between exact and approximate solutions.
 ICQ is about 30% greater with the approximate solution,
 VCEQ is about 10% less.
Voltage-divider Bias
Load-Line Analysis
 From the collector–emitter loop appears in Fig.

 The addition of the emitter resistor reduces the collector saturation level
Voltage-divider Bias
BDC effect (Stability)

This example is for testing how much the Q-point


will move if the level of BDC is cut in half

 The results show the relative insensitivity of the circuit to the change in BDC .
 Even though BDC is drastically cut in half, the levels of ICQ and VCEQ are
essentially the same.
 four additional methods for dc biasing a transistor circuit are discussed.
 These methods are not as common as voltage-divider because of the stability
 The more stable a configuration, the less its response will change due to
undesireable changes in temperature and parameter variations
 If the Q-point is highly dependent on BDC of the transistor, the configuration is
not stable.
 BDC is temperature sensitive, especially for silicon transistors, and its actual
value is usually not well-defined,

 Common Assumptions that could be


1. Base Bias used for simplification (if needed):
2. Emitter-Feedback Bias
3. Emitter Bias
4. Collector-Feedback Bias
8
9

1. Base Bias
• This method of biasing is common in switching circuits.
• The analysis of this circuit for the linear region shows
that it is directly dependent on BDC

 The Kirchhoff’s voltage law around the base circuit:

 The Kirchhoff’s voltage law around the collector circuit:

0 0
1. Base Bias
 Since IC is dependent on BDC
 That a variation in BDC causes IC and, VCE to change, thus changing the Q-point
of the transistor.
 This makes the base bias circuit extremely beta-dependent and unpredictable.

 BDC varies with temperature and from one transistor to another of the
same type due to manufacturing variations.
 For these reasons, base bias is rarely used in linear circuits

10
2. Emitter-Feedback Bias
 If an emitter resistor is added to the base-bias, the result is
emitter-feedback bias
 The idea is to help make base bias more predictable with
negative feedback (negates any attempted change in collector
current with an opposing change in base voltage).

 If the IC tries to increase, VE increases, causing an increase in VB because:


VB = VE + VBE.
 This increase in VB reduces the voltage across RB, thus reducing IB and keeping
IC from increasing.
 A similar action occurs if the collector current tries to decrease.

While this is better for linear circuits than base bias, it is still dependent
on BDC and is not as predictable as voltage-divider bias.

11
2. Emitter-Feedback Bias
 Calculating the emitter current:
write Kirchhoff’s voltage law (KVL) around the base circuit.

 The emitter current can be approximated by : IE = B IB

12
Stability Comparison between Emitter-Feedback Bias and Base Bias

131
Stability Comparison between Emitter-Feedback Bias and Base Bias
 As you can see, the Q-point is very dependent on in this (very unreliable).
 The base bias is not normally used if linear operation is required.
 However, it can be used in switching applications.
Determine how much the Q-point will change if the same circuit is
used but converted to emitter-feedback bias with RE = 1000 ohms

 Although it significantly improved the stability of the bias for a change in BDC
compared to base bias, it still does not provide a reliable Q-point. 14
2. Emitter-Feedback Bias
 Load Line equation: (Output loop similar to voltage-divider bias)

 From the collector–emitter loop appears in Fig.

 The addition of the emitter resistor reduces the collector saturation level

15

You might also like