 Microcontroller Based Protection for Low Voltage Motors using Zigbee

Technology: The main aim of this project is to protect and control low voltage motors
from low voltage, ground fault, thermal overload and unbalance conditions. Various
sensors employed in this design continuously monitors the parameters of the motor.
Microcontroller compares all these sensor data with respective set limits and accordingly
the switches the relay. This information will be sent to the remote PC using Zigbee
communication module.
 Protecting Induction Motor From Phase & Temperature:Over heating of a motor
can decrease the life time of the motor, causes insulation failure etc. Hence it is
necessary to protect the motor from single phasing and overheating. The present project
shows the hardware setup for monitoring the phases and temperature of the motors.
When there is any deviation in these two parameters, an SMS is sent using GSM.
 A Numerical Analysis of Coupled Electromagnetic and Heat Transfer Phenomena in
PM BLDC Electric Motor:This paper focuses on thermal management of electrical
motors. It study about , a coupled heat, flow (CFD) and electromagnetic (EMAG) model of
the permanent magnet brushless electric motor with electronic commutation was
formulated and then validated
 Four-Quadrant Adjustable Speed Drive for Series Wound DC Motors: In this
project, a four quadrant adjustable speed drive is implemented for series wound DC
motors which are mainly employed in electrical traction systems. PIC microcontroller is
used in this project to control the speed as well as direction of the motor. This project also
includes the current limiting as well as speed limiting protection circuits.
 Four Quadrant DC Motor Control without Microcontroller: This project deals with the
implementation of four quadrant motor controller using 555 timer along with H-bridge
driver. 555 timer produces the necessary PWM pulses to control the speed while relays
are used for changing the polarities and also to apply the brakes to the motor.

Electrical Power Project

1. Role of Surge Arrestors in Electrical Power Systems:Surge arrestors protect the
electrical equipment against over voltage. This paper presents the design and
characteristics of modern MO surge arrestors.
2. Power Generation Using Foot Step:This paper shows non conventional way of
generating the power. Unlike conventional ways here power is generated simply from
foot steps in the train.
3. Production of electricity by the method of road power generation:This project shows
the method of generating electricity from the road power generation. The device proposed
here converts the kinetic energy into mechanical energy ,there by producing electricity.
4. Wireless Power Transfer::A simple wireless power transfer device is developed in this
project without any microcontroller. Nikola Tesla realized the concept of wireless power
transfer. An efficient wireless power transfer system can eliminate the concept of current
carrying cables. A small DC fan is operated wirelessly from a distance of 3cm in this
project to demonstrate the working. Potential applications of the project are wireless
charging of mobile phones, laptops, iPods, etc.
 Control system
1. Design of Load Sharing control system using PIC Microcontroller: The main aim of
this project is to adjust the availability power with consuming load. This system measures
the power using current and voltage sensing circuits for every energy source i.e., for wind,
solar, grid and generator source. PIC microcontroller compares the load consumption and
then optimally connects the respective load to the healthier source.
2. Energy-based Control of an Under actuated Crane System with a Flexible Cable and
Large Swing Angle:In this paper, an effective energy based control technique for an
overhead crane system with a flexible cable with large swing angle is developed. The
studied crane system is categorised as a multi-degree under actuated system whose
characteristics can initiate challenges in control design.
3. Standalone Smart Solar-powered Streetlamp Light control System:This project
shows a solar powered street light control system. This light can be recharged using solar
powered system and it is controlled based on vehicle detection and audio recognition
technology.

SCADA
1. Cyber Security Analysis of Substation Automation System:The automated substation
uses SCADA for their implementation. It uses intelligent electronic devices for protection,
controlling and monitoring. Mod bus protocol is used for communication. This paper
explains about monitoring of substations and analyses cyber security issues of SCADA
systems.
2. SCADA Based Monitoring and Controlling Using Zigbee: This project implements
the real-time SCADA system using Zigbee communication technology. Zigbee activated
microcontroller unit along with set of sensors acts as a Remote Terminal Unit (RTU) while
Zigbee transceiver based PC acts as Mater Terminal Unit.
3. Intelligent Automation System For Electrical Energy Distribution:This research work
to be aimed at developing indigenous know-how of full scale Distribution Automation
system, which can cover from secondary substations to consumer level intelligent
automation, the power distribution automation is expected into broad areas. At present,
power utilities have to need full scale distribution automation to achieve real time system
information and remote control system. In modern power systems, the monitoring and
control of power substations are based on the computerised Supervisory Control and
Data Acquisition (SCADA) systems.

IEEE Electrical projects

1. Oil Field Retrofit of ESPs to Meet Harmonic Compliance:This paper discuses the
effects of harmonics in electrical distribution systems and practical solutions are given to
this.
2. Development of a power source for rural Electriciation: This paper discuses a
solutions for accessing electricity high voltage grid in rural community provided by station
service voltage transformer.

Electrical Projects using Labview

1. LabVIEW Based Power Analyzer: This project uses LabVIEW software to measure
and analyze the power quality parameters such as active and reactive power, harmonics,
instantaneous power and power factor. In this a power analyzer VI is implemented using
LabVIEW software along with DAQ board.
2. Implementation of PID and Fuzzy PD Controllers for DC Servo Motor: This project
implements fuzzy based PD and Ziegler-Nichols rule based PID controllers in order to
control the DC servo motor position. A DAQ board along with LabVIEW software is used
in this project to implement both controllers.
3. Real Time Data Monitoring of PV Solar Cell Using LabVIEW and DAQ: The data
acquisition board (DAQ) along with the LabVIEW software is used in this project for
monitoring photo voltaic cells in homes as well as industries. DAQ board acquires the
various parameters of solar cells and sends to LabVIEW software where we can monitor
those values in GUI.
4. Direct Torque Control of BLDC Motor : In this project direct torque control technique
for controlling the speed of brushless DC motors is simulated in order to attain faster
response of torque. This project uses LabVIEW software to develop the fuzzy logic
controller for this technique.
5. Simulation of Inverter Fed Induction Motor Drive with LabVIEW: This project
simulates the mathematical model of inverter fed induction motor using LabVIEW
software. This simulation is helpful for analysing the dynamic characteristics of motor.
6. Distribution Transformer Fuse Failure Detection and Information Passing
System: The main objective of this project is to detect the failure of fuse that employed at
the distribution transformer. This failure information is intimated to the concerned person
through GSM module. In this project LabVIEW based PIC microcontroller is used along
with the voltage sensor to detect fuse failure.
7. Wireless Design for Power Theft Monitoring: This project aims to implement anti-
power theft monitoring system using wireless sensor networks. This wireless sensor
device is a power metering device of the customer which sends the load information
periodically to the controlling station. The controlling station aggregates all the user data
and automatically detects the power theft user by comparing extra load consumed than
that of actual value.
8. Implementation of Frequency Locked Loop DC Motor Drive System: This project
implements the LabVIEW based frequency locked loop control algorithm for controlling
the speed of DC motor. This project describes capability to maintain the speed
stabilisation and regulation in order to recover the rated speed from load change.
9. Power Quality Monitoring and Power Measurements by using Virtual
Instrumentation: This proposed project describes the design of power quality
measurement and monitoring in LabVIEW environment. Various power quality parameters
 of voltage, current and power are measured and analyzed in this project using virtual
instrumentation techniques.

Electrical Projects using Arduino

1. Data Logger for Solar: The aim of this project is to measure and store the solar energy
parameters using Arduino controller. Sensors like LDR, temperature sensor, current
sensor and voltage sensor monitors the respective parameters of the solar panel. The
acquired data from Arduino controller is transferred to the PC where it is logged.
2. Implementation of an Omni Wheels Robot: This project builds Omni-directional robot
which can move in different directions. Arduino controller with motor driver circuit controls
the motion of the robot in different angles.
3. Differential Transformer Protection using Arduino: This project implements the
Arduino based differential protection for the transformer in order to protect the transformer
from various electrical faults. In this, current transformers along with Arduino controller
measure the differential current and if any fault occurs, it operates the relay.
4. Design Automatic Meter Reading (AMR) Data Logger with Xbee: This project
demonstrates the design of Automatic Meter Reading (AMR) data logger to read, collect
and store the energy consumption of various consumers remotely using Zigbee
technology. This design is implemented using Arduino controller and Zigbee
communication module.

PLC Based Electrical Projects

1. Control of Boiler Operation using PLC-SCADA: This project achieves the automatic
control operation of boiler using PLC and SCADA. Boiler temperature and pressure are
continuously monitored using temperature and pressure sensor respectively. The PLC
acquires these sensor values and depends on the control algorithm, it controls the
actuators. SCADA system enables the remote monitoring and control of boiler operation.
2. PLC Based Intelligent Traffic Control System: This project aims to implement an
intelligent based traffic control system using sensors and PLC. Photoelectric sensors
detect the presence of vehicles on various junctions of the road and give the signals to
the PLC. Based on the program in the PLC, it controls the traffic signals.
3. PLC Based Robotic Arm Control System: This project implements the robotic ARM
control system using PLC for precise control. Programmable logic controller (PLC) is
programmed to perform different ARM movements by giving the corresponding signals to
motor driver circuit.
4. Implementation of PLC Based Elevator Control System: This project describes the
implementation of elevator control system using PLC. Hall Effect sensor detects the
position of the elevator and gives the corresponding signal to the PLC. According to the
program in the PLC, it generates the control signals to the DC motor to control the
movements of elevator.
5. Design of PLC and SCADA Based Control Panel for Continuous Monitoring of 3-
Phase Induction Motor: In this, an efficient and versatile tool for controlling the induction
 motor is proposed which control and monitors the speed with high accuracy. A variable
Frequency Drive (VFD) based PLC controls the speed of the motor at better regulation.
SCADA system for this project is implemented for remote monitoring and control of the
speed.
6. PLC Based PID Speed Control System: This project deals with the design of
intelligent drive controller for AC motor by implementing PID (Proportional-Integral-
Derivative) control scheme. This project achieves the precise control by exactly tuning the
PID parameters using Ziegler-Nichols methods.
7. PLC Based Induction Motor Starting and Protection: In this project, slip ring induction
motor starting, protection and speed control schemes are implemented using
programmable Logic controller (PLC). Rotor resistance control method is implemented as
starting method while over voltages, over current and over temperature protection
schemes are implemented to protect the IM.
8. PLC Based Object Sorting Automation
9. This paper explains about automatic object sorting system that sorts the objects
depending on the weight and height which is controlled by the programmable logic
controller. This is a low cost ,low maintenance and long durability system.
10. Programmable Switching Control using 8051 Microcontroller :This project
develops system that functions similar to the PLC using 8051 microcontroller. Sequential
switching of loads is achieved in this project.

Miscellenous
1. ARM 7 Based Controller Area Network for Accident Avoidance in Automobiles:The
project shows an accident avoidance system. Here this system measures various
parameters like speed, distance from other cars, alcohol presence in the cars etc. It sends
signal if any of the parameters were changed. This also detects the accident using bump
sensor and sends an SMS using GSM.
2. Route Guidance For Blind People Using GSM & GPS Modems:This paper presents a
smart electronic aid for blind people. The proposed system uses and ultrasonic sensor for
detecting the obstacles in the path.GSM, GPS modules were used to locate the blind.
3. Brushless DC Motor Design for Electric Traction System: BLDC motor is used in
residential ,commercial and aerospace systems due to its various features. This paper
explains the designing of BLDC motor drive.
4. Switched Reluctance Motor for Hybrid Electric Vehicle:Switched reluctance motor is a
type of stepper motor that runs by reluctance torque. It is gaining popularity in application
of hybrid electric vehicle. The present project aims at reducing the torque and speed
ripple to make it suitable for hybrid electric vehicle using non linear controller.
5. Micro Controller Based Ac Power Controller: A single phase PWM inverter is designed
in this project. It has features like simple, low cost, compatible size etc.
6. Design and Simulation of Novel Integral Switching Cycle Control for Heating
Load:There are two methods employed for solid state power controls. One is Phase
control switching and the other is integral cycle control switching . These two have their
own disadvantages. To overcome this a new method called integral switching control is
proposed in this paper.
7. ATM Terminal Security using Fingerprint Recognition:ATM’s provide convenient
banking to the customer. But these days there are security issues in using ATM’s.This
paper develops a method to overcome this security issue and provides more security to
the customer banking. This system uses a finger print scanner for authentication of the
customer.
8. Development of Anti rigging Voting System Using Finger Print:Voting is practised on
electronic machines now a days. This project provides a voting machine that is reliable
and secured. It uses finger print scanner to provide unique identity to every citizen.
9. Fault Acknowledgement System for UPS using GSM: This paper shows the designing
of an UPS system that acknowledges faults in the System using GSM technology.
10. Touch Screen GLCD based Digital Devices Control System:This project replaces the
mobile devices that operate home appliances by touch screens. A touch screen based
digital control of devices is shown here.
11. Real-time Posture and Activity Recognition by Smart Shoe:In this paper, we discuss
a method for performing automatic posture classification using Artificial Neural Networks
operating with fixed point precision arithmetic. The computational time is optimised
through application of forward feature selection for determination of the most significant
predictors.
12. Load Frequency Control – An ELC based approach:This project shows load
frequency control of a micro grid control system. This system is tested in mat
lab/simulink.
13. Internet of Things for Smart Classrooms:This project uses internet of things for smart
classrooms where the time of students and the teacher g were reduced in maintaining
the queues and listening to the instructions.
14. E- Health Care Computing for better Health Monitoring : This project shows an
automatic health care system for monitoring the health of the patients. This system uses
some wearable sensors and portable wireless devices. Condition of the patient
is transmitted to the doctor and related people using GSM or Bluetooth.
15. Renewable energy based interleaved boost converter: Renewable energy
consumption is increasing day by day due to decrease in non renewable energy sources.
Among them solar energy is the best source. Boost converters are required to increase
the output. Here interleaved converter is such a converter that has a number of
converters connected in parallel. It has very good advantages compared to others in
efficiency, reliability etc.
16. Design and Construction of 33/11 KV Line & Substation:This project shows the
construction of 33/11kv line and substation.
17. Active Power Control of Grid-Connected Distributed Generation Unit:Distributed
generation using non conventional energy sources is increased .This paper
shows simple and efficient a control technique to get desired power from DG to grid.
18. Three Phase Rectifier with Power Factor Correction Controller:This paper
shows power factor correction of a three phase rectifier using boost converter. Average
current control technique is used in this .Results are verified in mat lab.
19. Remote Surgical Robotics: Control Systems and Human-Machine Interfacing:Here
is the remote surgical robot. The main aim of this robot is to detect the surface of gelatin
brain using robot.
20. Simulation Of Three Phase Multilevel Inverter With Reduced Number Of
Switches:Multi level inverters can be used in many applications because of their
flexibility, easy control, less cost. Though it has many advantages this multi level inverter
(MLI) has number of power electronic components. Increased number of switches
increases over all loss as switching losses increases. This paper mainly focuses on
decreasing the number of switches in MLI.
21. Hybrid Solar Wind Charger:Generally UPS uses supply from the main for its functions.
This paper shows a UPS system that uses solar and wind power instead of mains supply
as there is energy crisis.
22. Cyber Security in the Smart Grid:The smart grid is revolutionary in the existing power
grid. The smart grid system enhances the future power system. Due to number of inter
connected devices, there is a problem in cyber security. This paper focuses on the cyber
security in this smart grid.
23. Speed Control of Switched Reluctance Motor Using ANFIS and GA:Switched
reluctance motors are best for direct drive applications. But it has some draw backs like
high torque ripple, acoustic noise, speed oscillations. This paper proposes a method for
using ANFIS and GA u for Drive control.
24. Stability Analysis Using Power System Stabilizer: This paper describes the operating
performance of Power System Stabilizer (PSS) during different power system case
studies. The functional blocks of PSS are developed in Simulink and simulation is carried
out. The damping oscillation variation of PSS for the various power system conditions
(light, nominal & high load and fault) is carried out and the voltage and reactive power
variations are illustrated.
25. Sensor Fault Detection in Induction Motor Using Fuzzy Logic Controller with D-Q
Transformation:This paper proposes a method for speed and fault detection in current
sensor. It provides isolation to protect the motor from speed and current sensor failures.
26. Intelligent Control Technique Based Zeta Converter Fed PMDC Motor: This paper
deals with the implementation of fuzzy-PI based Zeta converter fed PMDC motor with
high efficiency, less total harmonic distortion and good power factor adjustment.
27. Captive Liquid Power SYSTEM:The most known process for generating electricity from
water is by storing the water in dams. This paper explains an extension to this method.
Initially water is held in captive in an enclosure. Then it is raised to high potential energy
using wind or water.
28. Power System Design for an Electric Car: This project shows the power generation
and distribution system of electric car. This shows converting a gas powered car into
battery powered and uses solar panels to recharge the battery.
29. Star Delta Starter using Adjustable Electronic Timer for Low power Induction
Motor: This project aims to provide cost-effective star delta starter for low power three
phase induction motor in order to provide low voltage start. This project uses 555 timer in
mono-stable mode which drives GTO (Gate Turn-Off) thyristors driver circuit so as to
change the mains three phase supply from start to delta.
30. Programmable Switching Control for Industrial Automation in Repetitive Nature of
Work: This project implements the programmable load switching control using
microcontroller for applications where repetition of nature of work involved. This project
operates in three modes namely manual mode, auto mode and set mode. In manual
mode, various loads are controlled by the input given by user by switches or remotely
 through GSM. In auto mode, loads are switched at regular default timings while in set
mode loads are controlled based on the timings set by the user.
31. Automatic Induction Motor Starter with Delay Using Microcontroller: This projects
implements an automatic induction motor starter using microcontroller which works same
as that of DOL starter. The microcontroller continuously monitors the three phases of
input supply for over voltage and single phasing conditions and accordingly switches the
relays to switch the motor.
32. Microcontroller Based Speed Control of Three Phase Induction Motor using V/F
Method: This proposed project implements the microcontroller based hardware design to
control the speed of three phase induction motor using V/F method. By receiving the
feedback signal of speed, microcontroller will give PWM signals to the IGBT inverter
bridge in order to drive the motor at desired speeds.
33. Power Factor Correction Using PIC Microcontroller: This project measures the power
factor of the load using PIC microcontroller along with zero voltage and zero current
crossing detector circuits. According to the set limits for leading and lagging power
factors, microcontroller switches set of capacitors to improve the power factor.
34. Underground Cable Fault Distance Locator: This project demonstrates a fault locating
model which determines the fault that occurs in underground cables using microcontroller.
This design uses the concept of Ohms law for detecting the change in voltage across the
cable whenever fault or short circuit takes place in the cable.
35. Three Phase Fault Analysis with Auto Reset for Temporary Fault and Trip for
Permanent Fault: The objective of this project is to develop an automatic tripping
mechanism for both permanent as well as temporary faults that are takes place in three
phase system. This project uses 555 timer as a main controller which resumes the load
when a temporary fault occurs in three phase system while it makes the load to be remain
in tripping mode during permanent fault.
36. Automated Wireless Energy Meter Reading System using GSM: This project
implements an Automatic Metering Reading (AMR) System for energy meter without any
human intervention for generating the electricity bill. This project uses ARM controller for
measuring electricity consumption a given period of time. Further, this billing information
is sends to utility companies as well as to the customers using GSM module.
37. BLDC Motor Speed Control with RPM Display: In this project the speed a BLDC
motor is controlled precisely using microcontroller unit along with the hall position sensor.
The microcontroller is programmed in such a way that it compares the actual speed (get
from hall sensor) with desired speed and accordingly genrates the PWM signals to the
motor driver unit.
38. PC Based Electrical Load Control: This project uses a personal computer to control
various electrical appliances in homes by using microcontroller. Microcontroller acts as a
data acquisition and control device which forms the bridge between PC and electrical
appliances. Microcontroller receives the command signals from PC and appropriately
controls the respective load.
39. Wireless Auto Power Trip during Gas Leakage: This project aims to reduce the fire
accidents that are takes place due to gas leakage in the presence electricity. In this
project gas sensor monitors the gas leakage which gives the input to microcontroller when
it senses the gas leak. Then the microcontroller activates the tripping mechanism to
 shutdown the power supply. RF module used in this project to transfer the information
remotely to the alarm circuit and tripping circuit.
40. Solar Powered Auto irrigation System: The main aim of this project is to implement
solar based automatic irrigation system for switching the pumping motor depends on the
signal from soil moisture sensor. By receiving the signals from the sensor, microcontroller
performs the switching of pump using relay.
41. Zigbee Based Home Automation System: The aim of this project is to implement a
home automation system to control the home appliances remotely using Zigbee
technology. Sensors like temperature, LDR and gas detection sensors connected to the
microcontroller unit continuously monitors the weather parameters. The home appliances
are automatically controlled when these parameters exceeds their set limits. Remote
monitoring and control is also facilitated with Zigbee communication.
42. Photovoltaic Panels Monitoring and Solar Energy Measurement System: This
project monitors the parameters of photovoltaic cells and measures the solar energy
generated. A set of sensors along with microcontroller unit continuously monitors the solar
energy and also allows the user to access the remote monitoring of these parameters.
43. Smoke and LPG Gas Detection Robot with Wireless Control: The objective of this
project is to design an RF robotic vehicle to detect the LPG and smoke for underground
mining applications. The RF communication module attached with robot sends the sensed
data to the central monitoring area.
44. Remote Monitoring System for Three-Phase Distribution Transformer using
Zigbee : In this project, parameters of a three phase distribution transformer are
monitored and controlled remotely using Zigbee communication. Transformer parameter
like temperature of the oil, oil level, voltage, current, etc are continuously monitored using
various sensors. The sensor data is transmitted to the central controller using Zigbee
module.
45. Solar Powered LED Street Light with Auto Intensity Control: In this project, an
energy efficient method for street lights is implemented to control the LED street lights.
The power generated by the solar panels is stored in batteries during the day time and at
the night this energy is supplied to the street lights. As the traffic on roads decreases from
peak hours to late nights, this projects controls intensity of street lights based on timings.
46. Wireless Power Transfer System using Magnetic Resonant Coupling: This project
transfers the electric power from one circuit to the other without using any conducting
medium between them. In this project, magnetic resonant coupling method is
implemented to transfer the power from the source to a load.
47. Wireless DC Motor Control using DTMF Technology: The idea of this project is to
perform wireless speed control of a DC motor from a mobile phone using DTMF
technology. DTMF decoder receives the DTMF signals from the remote mobile to control
the speed of a DC motor.
48. Cable Inspection Robot using Microcontroller and GPS Tracker: This project
implements the underground cable fault detecting mobile robot that can navigate along
the underground cable. This inspects fire accidents, obstacles, supply failures, presence
of harmful gases, etc of the cable. GPS module facilitates finding of fault location and this
information is further transferred to the main controller through the communication
module.
49. Induction Motor Speed Control Using Android Application: The objective of this
project is to control the speed of a single phase induction motor from Android mobile
application. Bluetooth module attached to the control circuit receives the control
commands from user mobile. Microcontroller receives these signals and controls the
motor speed by varying the triggering pulses to the TRIAC.
50. Wireless Automatic Railway Gate Controlling cum Traffic Signaling: In this project,
the level crossing gate as well as railway level crossing traffic lights are controlled using
microcontroller unit along with IR sensors. IR sensors at particular positions on the track,
gives the input to the microcontroller about the train arrival and departure information.
According to these signals microcontroller controls gate operation as well as traffic lights.
51. Wireless Meter with Theft Monitoring and Control System: This project aims provide
the automatic energy meter reading and to prevent practice of power theft. In this project,
the overloading resulted from power theft is detected and this information is conveyed to
the authorities through communication network.
52. Patient Monitoring System using GSM: In this project, human body vital parameters
like pulse rate, body temperature and saline level are continuously monitored by various
sensors using ARM microcontroller. Further, these monitored values will be sent to the
remote mobile using GSM modem.
53. Design of a Low-Cost Contact-Less Digital Tachometer : This project measures the
RPM or speed of a moving object (say motor) without any direct contact with it. The
microcontroller receives the IR sensor data, processes it and converts it into RPM. RF
communication module transfers this data to remote PC where it is recorded and stored.
54. A Hybrid Wind-Solar Energy System: The main aim of this project is to switch the
loads to either wind or solar energy source depending on the maximum power generated.
This circuit also uses MPPT system for maximum power generation.
55. Smart Phone Based Home Appliance Control : This project uses the Smartphone to
control the various household appliances such as fans, lights, kitchen appliances, etc.
The microcontroller unit along with Bluetooth module receives the control signals from
user Smartphone and then controls the home appliances.
56. Automated Water Head Controller for Domestic Application: The aim of this project is to
design a water level sensing device using ultrasonic sensor which measures the water
level without any direct contact with water. Ultrasonic sensor gives the sensing
information to the ATmega controller which further processes the data and indicates the
level information.
57. Electric Power Management using Zigbee Wireless Sensor Network: The main aim
of this project is to implement a system which differentiates and controls the devices in a
network on the basis of power consumption of individual appliance. Zigbee
communication enables the monitoring the various load consumptions and accordingly
controls the load depends on the availability of power.
58. Ultra Fast Acting Electronic Circuit Breaker: This project demonstrates the ultra fast
electronic circuit breaker that isolates the load circuit from mains supply at extreme faster
rate as compared with bimetallic strip based circuit breaker. PIC microcontroller with
current sensor unit detects short circuit or overload and appropriately turns the MOSFET
in order to switch the load.
59. Design and Development of Microcontroller Based Solar Charge Controller: This
project implements the solar charge controller circuit which charges the battery with
 amount of charge coming from solar panel. This circuit also regulates voltage to protect
the battery from overvoltage and do not allow the battery to go into deep discharge.
60. Interactive Voice Response (IVR) System for Educational Institution:This project
aims to build Interactive Voice Response (IVR) system for educational institution based
on DTMF technology. Using this system, user can access the information stored in the
database by pressing corresponding key on his/her mobile. DTMF decoder with
microcontroller unit achieves this operation.
61. Solar Tracking Solar Panel Using ATMEGA8 Controller: The purpose of this project
is to generate the maximum solar energy from the PV panel depends on intensity
detected by Light Dependant Resistors. Microcontroller adjusts the direction of solar panel
towards the sun based on the signals from LDR.
62. Automated Toll Tax Collection Using GSM and RFID: This project implements the
automatic toll tax collection by facilitating advance registering through SMS.
Microcontroller unit with GSM modem receives the request from vehicle owners and
sends the acknowledgement including the password to user mobile. At the time vehicle
reaching the toll plaza, microcontroller asks for password, upon authentication it deducts
the amount from RFID attached to the vehicle automatically, and then opens the gate.
63. Transient Stability Analysis of Power System Using MATLAB: The objective of the
project is to design the stability analysis of power system as simulation model in
simulink/MATLAB. For the assessment of transient stability, a multi-machine system is
implemented in this project.
64. Data Logger and Remote Monitoring System for Multiple Parameter Measurement
Applications: This project aims to build an embedded system that performs data logging
and remote monitoring of various parameters. The environmental parameters like
temperature and humidity are monitored with sensors. AVR microcontroller acquires the
sensor data and makes a record of it in EEPROM. This project also facilitates to monitor
the acquired or logged data through GSM module.
65. Touch Screen Based Wheelchair System: This project controls the direction and
speed of DC motors which are attached to the wheelchair so that it moves in desired
direction. This ARM controller with touch screen enabled design is very helpful for
physically disabled persons to control their wheelchair.
66. Simulation Model of Hydro Power Plant Using MATLAB/Simulink: This project
implements the simulation model of hydro power plant with hydro turbine and
synchronous generator on MATLAB platform. This work is useful for conducting operating
tests as well as for analyzing the results.
67. Battery Monitoring System using Microcontroller: This project implements a battery
monitoring system for UPS, telephone communication and hybrid electrical vehicle
applications. Battery parameters like voltage and temperature continuously monitored
using slave microcontroller unit while master controller gathers all the batteries
information.
68. Design and Development of a Parabolic Dish Solar Water Heater: The main aim of
this project is to develop the parabolic dish solar water heater for water heating
applications. In this embedded electronic circuit is implemented for the parabolic dish to
track the sun continuously in order achieve high efficiency.
69. Voice Operated Robotic Vehicle: The main objective of this project is to control the
movements of robotic vehicle through voice commands of the user. The Speech
 recognition module along with RF transmitter sends the voice signals to remote robot. RF
receiver in the robot correspondingly receives the signals and controls the robot
movements.
70. Design and Simulation of Fuzzy Controlled SVC for Transmission Line: In this
project Static VAR Compensator scheme is implemented for transmission line based on
fuzzy logic. This system controls the reactive power by implementing the firing angle
control scheme in MATLAB.
71. Maximum Power Point Tracking for Low Power Photovoltaic Solar Panels: This
project describes the enhancement of power generated by the solar panel using MPPT
algorithm. This MPPT (Maximum Power Point Algorithm) implemented on microcontroller
in order to maximize the output.
72. Android Mobile Phone Controlled Bluetooth Robot using 8051 Microcontroller: This
project involves in the designing of Android mobile application controlled robot using
microcontroller. Android application based control commands received by Bluetooth
module enables the microcontroller to control the DC motor speed and direction.
73. Street Light Glow on Detecting Vehicle Movement using Sensor : The main aim of
this project is to implement an energy efficient street lighting system which controls the
street lights based on the movement of vehicles on the road. Microcontroller with set of IR
sensor detects the vehicle movement and with this sensed data microcontroller switches
the street lights.
74. Footstep Power Generation using Piezoelectric Sensors: This proposed system
presents the usage of piezoelectric sensors to generate the power from human foot
pressure. The power generated from the piezoelectric sensors is stored in the battery and
inverter converts the battery voltage (DC) to load operating voltage (AC). Microcontroller
unit measures the power generated by these sensors and accordingly displays the
amount of power generated.
75. Speed Synchronization of Multiple Motors using Microcontroller: This project uses
RF communication to synchronize the multiple motors in an industry. In this, all the motors
are equipped with RF transceiver module along with microcontroller unit. This
arrangement causes to change the speed of remaining motors if speed of the one motor
is changed.
76. Head Movements based Wireless Device Switching : The main aim of this project is
to switch the electrical loads or devices based on the head movements of a person using
MEMS sensor. This type of project is helpful for physically challenged and paralyzed
persons.
77. Bidirectional Rotation of an Induction Motor with a Remote Control Device : This
project aims to control the speed and direction of induction motor using TV remote. IR
sensors and microcontroller unit are used in this project to receive the signals from TV
remote. A relay driver is connected to the microcontroller unit to change the direction of
motor.
78. Hall Effect Sensor Based Portable Tachometer for RPM Measurement: This project
deals with the implementation of portable, accurate and contactless tachometer using
linear Hall Effect sensor. This sensor produces the number of pulses per revolution which
are given as input to the microcontroller unit. Microcontroller measures these pulses per
minute in order to give the RPM display.
79. Wireless Load Control Device using GSM Module: The intention of designing this
project is to make more convenient and time saving method to control the loads from
remote places. This project uses GSM module with microcontroller unit to receive user
control commands to switch ON/OFF the particular load.
80. Design and Implementation of IGBT Based Single Phase AC Drive using PIC
18F452: This project implements single phase AC drive to control the speed of induction
using PIC microcontroller. A constant voltage per hertz technique is implemented in this
project by generating PWM pulses to drive the IGBTs.
81. On-Line Monitoring and Analysis of Faults in Transmission and Distribution Lines
using GSM: This project uses the GSM technology to convey the fault information of
transmission and distribution lines to utility department. In this project microcontroller unit
along with sensors detects the faults that are takes place in power lines.
82. Wireless Temperature Data logger Using Zigbee: This project develops a
temperature data logger system using microcontroller and Zigbee communication module.
A temperature sensor with ADC enables the continuous acquiring of temperature data at
the field side where Zigbee transmitter module is employed. At the receiver side, Zigbee
receiver with microcontroller unit receives and logs the temperature data.
83. Microcontroller Based Active and Reactive Power Measurement: This design aims
to measure and indicate the active and reactive power of an electrical system using PIC
microcontroller. With the help of input from zero crossing detector circuit, PIC
microcontroller calculates these two parameters and stores the data in EEPROM.
84. Simulation of Extra High Voltage Long Transmission Lines: In this project, simulation
of EHV long transmission lines is performed in order to analyze various parameters and
circuit condition under normal working conditions.
85. Microcontroller Based Modified SEPIC Converter for Driving Lamp with Power
Factor Correction: This project presents a topology of Single-Ended Primary Inductance
Converter (SEPIC) with half bridge inverter to feed the electrode less fluorescent lamp.
This project improves the power factor and reduces the total harmonic distortion.
86. Substation Monitoring and Control using Zigbee: The objective of this project is to
develop the remote monitoring and control system for substation using Zigbee module.
Various parameters of the distribution transformer in substation are continuously
monitored using Zigbee module. Zigbee receiver at the main station acquires these
parameters and takes action accordingly.
87. A Transformer-less Voltage Quadrupler DC-DC Converter with Low Switch Voltage
Stress: In this project implements the interleaved quadrupler voltage DC-DC converter to
achieve high voltage gain and to reduce current ripples and conduction losses. This
design uses three stage interleaved boost converter with voltage quadruoler circuits.
88. Power System Stability Enhancement by Simultaneous AC-DC Power
Transmission : The main aim of this project is to present the simulation of simultaneous
AC-DC power transmission by superimposing DC on AC. This project replaces the
parallel AC-DC transmission by converting double circuit AC into composite AC-DC
transmission line. This work is simulated in MATLAB platform.
89. Analysis of DC-DC Converters for Renewable Energy System: This project analyses
the selection of DC-DC converter with transformer to produce the desirable characteristics
for electrolyser applications using MATLAB. In this, ripple-free regulated output is
produced by the DC-DC converter.
90. Simulation and Comparison of SPWM and SVPWM Control for Three Phase
Inverter: This project deals with the modeling of Space Vector Pulse Width Modulation
(SVPWM) technique which effectively uses the DC bus voltage and produce the less
harmonic content as compared with Sinusoidal PWM technique. This model is simulated
using Simulink/MATLAB and results are compared with SPWM technique.
91. Modeling of Induction Motor and Fault Analysis: In this work, induction machine
model is implemented in Simulink/MATLAB to analyze the motor performance and for
effectively diagnosing the rotor faults. This analysis is carried out for single, double and
three bar broken rotor faults.
92. Improved AC-AC Converter For Induction Heating Applications: This MATLAB
based project simulates the single-switch parallel resonant converter (improved AC to AC
converter) to produce high frequency currents for induction heating applications. The
analyzed results are compared with existing half and full bridge inverter topologies.
93. Solar Powered Mobile Charger Using Buck Converter: This project aims to build
solar powered mobile charger circuit using synchronous buck converter. The DC power
obtained from the PV array is synthesized and modulated using this buck converter in
order to meet the load requirements.
94. Modeling & Simulation of Doubly-Fed Induction Generator for Variable Speed
Wind Energy Conversion Systems : The objective of this project is to model and
simulate the double-fed induction generator in the MATLAB Simulink environment. Based
on the vectorized dynamic approach, DFIG model is described in this project.
95. Automation of Coal Handling Plant of a Power Generation Unit using PIC
Microcontroller: This project demonstrates the automation of coal handling plant of a
thermal power generation unit using proximity sensors and PIC microcontroller. Based on
proximity sensors signal, microcontroller controls the speed of stepper motor which further
drives the conveyor belt. This also implements the interlock facility in motors to provide
the safety.
96. Speed Control of Universal Motor Using Microcontroller: A TRIAC and
microcontroller based circuit is implemented in this project to control the speed of
universal motor. Microcontroller provides the phase angle control of TRIAC which varies
the power through universal motor.
97. Conductor Temperature and Sag Monitoring System using Zigbee and GSM : This
project aims to measure and monitor the sag and temperature of high voltage overhead
conductor using sensors without making any interruption to the continuous power supply.
These sensed parameter values are send to the central monitoring station using Zigbee
module and also to the authorized persons using GSM module.
98. Implementation of Programmable Automatic Voltage Regulator: The main aim of
this project is to implement Programmable Automatic Voltage Regulator (PAVR) using
microcontroller. This project achieves the stabilization of output voltage with the deviation
of input voltage from 100 to 340 volts.
99. GSM Based Automated Embedded System for Monitoring and Controlling of
Smart Grid: This project demonstrates the remote monitoring of smart grid parameters
using GSM module. Electrical parameters like voltage, current, power and frequency are
acquired by the data acquisition device. These real time values are periodically send to
authorized persons through GSM network.
100. Measurement of Air Breakdown Voltage and Electric Field using Standard Sphere
Gap Method: In this project, air breakdown voltages and electric field of the high voltage
equipment are measured by using sphere gap method for the measurement of high
voltages.
101. Calculation and Analysis of Transformer Inrush Current of Transformer: In this
work, analytical formulas are implemented to calculate the inrush current in transformer.
And then the effect of switching angle variation, remnant flux and energizing circuit
impedances on inrush current characteristics are analyzed using MATLAB.
102. Inductance Capacitance and Frequency (LCF) Meter : The main aim of this project is
to implement a portable instrument to measure inductance, capacitance and frequency.
This two probe device is implemented using PIC microcontroller with additional circuitry
for accurately measuring and displaying these parameters.
103. Circuit Breaker Based Feeder Pillar with Over current and Earth-Fault
Protection : This project aims to design and simulate the 415V AC feeder pillar with earth
fault, overload and over current protection using earth leakage CB, three phase overload
relay and sequence relay. This design and simulation is performed on MATLAB platform.
104. A Domestic Robot for Security Systems Using Zigbee Technology: This project
aims to build a robotic vehicle that can enhance the security at homes. This project
achieves the door locking system with active input from ultrasonic sensor and PIR
sensors. A camera attached to this system enables the remote monitoring using Zigbee
technology.

For more knowledge on various projects ideas, visit the following pages:

1.
1.
1.
1.

1. List of Embedded Systems Projects

2. List of Robotics Projects Ideas
3. Communication Projects List
4. List of Solar Energy Projects

Comments

1. James Mwendwa says

DECEMBER 8, 2015 AT 1:05 AM
Nice projects. I liked them.
Do you mind sending me a power related project.. Please do if you can via my email.

Reply

1. Administrator says

JANUARY 20, 2016 AT 2:12 PM

Here it is https://www.electronicshub.org/top-power-electronics-projects-ideas/

Reply

2. kassim says
JANUARY 5, 2016 AT 5:17 AM
I sincerely liked and appreciated your works guys

Reply

3. Mbua Bleck says

FEBRUARY 15, 2016 AT 1:21 PM

Nice projects, i like them. I think number 12 is good for me.

Reply

4. mohd taalib says

MARCH 3, 2016 AT 2:32 AM

all project are usefull my engg. life

Reply

5. arnaud yunusu says

APRIL 18, 2016 AT 2:50 AM

good projects

Reply

6. rahool chindra says

APRIL 28, 2016 AT 5:51 AM

Thanks, this is very impressive article, you have collected almost very useful data..

Reply
7. Mohsin says
APRIL 28, 2016 AT 2:08 PM

Will you please suggest me a final year project related to power

Reply

8. shahnawaz mansuri says

MAY 5, 2016 AT 8:08 AM

finally I got complete knowledge about my project with the help of this side

Reply

9. James.V.O says
MAY 5, 2016 AT 8:52 AM
Pls, admin if u hv d project 4 d topic below, cn u help m send it throug my e-mail. Constructiön
and implementation of a micro controller based such, over voltage and under current line
protection

Reply

10. Manik Raj says

MAY 26, 2016 AT 1:54 AM

Thanks to give us knowledge about these projects

Reply

11. Manik Lal Thakur says

MAY 26, 2016 AT 1:56 AM

Thanks to give me knowledge about these projects

Reply

12. sandeep says

JUNE 13, 2016 AT 11:30 AM

Its very help full to all engg. Students.

Reply

13. Vuyo says

JULY 11, 2016 AT 12:08 AM

interesting projects. i would love to get more info about number 35

Reply
14. samuel says
JULY 14, 2016 AT 2:14 AM

nice articles

Reply

15. Tejas sonagara says

JULY 28, 2016 AT 11:39 AM

Awesome… All the projects are A1 grade..

Reply

16. geh emmanuel says

AUGUST 1, 2016 AT 2:14 AM
wonderful projects but need project on camera monitoring system

Reply

17. manish sarvaiya says

AUGUST 11, 2016 AT 3:35 AM

excellent work for the engg. student…. congrate..

Reply

18. Shweta Sharma says

AUGUST 27, 2016 AT 12:03 AM

Very nicee projects and ideas. Great list

Reply

19. santosh kumar says

SEPTEMBER 16, 2016 AT 1:31 AM

Nice projects. I liked them.

Do you mind sending me a solar power related project.. Please do if you can via my email.

Reply

20. Hlaing Phyo Aung says

SEPTEMBER 26, 2016 AT 9:08 AM

Pls send me small project detail for three phase faults theory with step by step illustrations for
our final yr project at GTU Myanmar

Reply
21. Nas says
OCTOBER 24, 2016 AT 10:17 PM

Any ideas for electronicmagnetic related projects? Please help, thanks.

Reply

22. gowthami says

DECEMBER 2, 2016 AT 11:25 AM

I want eee project topics for final year

Reply

23. Renatus Rwegasira says

DECEMBER 26, 2016 AT 11:27 AM
Nice project ideas, really appreciated.
Just send me project idea reports on enverter based protection system.
(through my email address)

Reply

24. abu says

MARCH 17, 2017 AT 12:19 PM

please help me about the project automatic room temperature control by plc

Reply

25. Damaris says

MARCH 27, 2017 AT 5:41 AM

Very nice project , please can I get project titles

Reply

26. kirui isaac says

APRIL 30, 2017 AT 10:19 AM

I need a project for control system and programmable logic controllers

Reply

27. Aloisio Cesar says

MAY 31, 2017 AT 1:55 AM

Good day,
you have nice good projects. I am on my final year and I got interested in your projects,

May you please help me with one of this projects:

– Power Generation Using Foot Step

– Wireless Power Transfer
– Production of electricity by the method of road power generation

Regards,
Aloisio Cesar

Reply

28. Gausu says

AUGUST 23, 2017 AT 1:50 AM

I want your help

Reply

29. nash says

AUGUST 28, 2017 AT 5:52 PM

very nice projects.i want to see more electrical machines project

Reply

30. Gabriel says

NOVEMBER 14, 2017 AT 8:42 PM

Wonderful projects,! I need a topic about distribution energy and renewable energy.

Reply

31. mukesh kumar says

FEBRUARY 2, 2018 AT 1:25 AM

Nic bro

Reply
32. Yeukai Chabata says
FEBRUARY 19, 2018 AT 2:18 PM

Wonderful projects there.

May you send me an electric motor related project via email

Reply

33. baksman says

FEBRUARY 21, 2018 AT 2:08 PM

nice project topics….

would you please send me a project on temperature controlled fan or

three phase changer using radio frequency remote….

thanks…

Reply
34. mesfn says
MARCH 9, 2018 AT 12:06 PM

woooow very interesting projects i realy liked them please give me some hilights about
semester end projects if you can with my email.

Reply

35. Sail says

APRIL 10, 2018 AT 12:50 AM

Keep it up…I totally appreciate your work…

Reply

36. Gokula vanishree says

APRIL 28, 2018 AT 10:25 PM
It’s so useful for us to ull very much

Reply

37. Electrical design. says

OCTOBER 30, 2018 AT 1:03 AM

This is an incredible rundown of free PCB structure programming.

A debt of gratitude is in order for sharing this rundown.

Reply

38. Sibi says

NOVEMBER 14, 2018 AT 3:09 AM

The list is so interesting and covers the concept of electrical engineering.

Thanks you for the projects
Reply

39. Alvin says

JANUARY 3, 2019 AT 4:52 AM

i need simple and low cost project in electrical

Reply

40. ohiomakise says

APRIL 24, 2019 AT 10:09 PM

HYE THERE, IS THERE ANY CHANCE FOR ME TO GET A GUIDE ON DEVELOPING A

PROJECT ON CONTROL SPEED OF THREE PHASE INDUCTION MOTOR USING VFD BY
GENERATING SPWM BASED ON ARDUINO? BTW, IT IS 6 OUTPUT PWM SIGNALS.

Reply
Leave a Reply
Top of Form

Your email address will not be published. Required fields are marked *

Comment

Name *

Email *

Website

Bottom of Form

Top of Form

Bottom of Form

PCB Assembly Services

PROJECTS BY CATEGORY

Arduino Projects (200+)

Electronics Projects (250+)
Mini Project Circuits (160+)
Mini Project Ideas (150+)
ECE Projects (150+)
EEE Projects (150+)
8051 Projects (110+)
Raspberry Pi Projects (101+)
Electrical Project Ideas (100+)
Embedded Projects (100+)
Latest Electronics Ideas (100+)
Microcontroller Mini Projects (100+)
Robotics Projects (100+)
VLSI Projects (100+)
Solar Projects (100+)
IOT Projects (100+)

Communication Projects (70+)

LED Projects (70+)
Power Electronics Projects (60+)
RFID Projects (60+)
Home Automation Projects (50+)
Matlab Projects (50+)
EIE Projects (50+)
Wireless Projects (50+)
LabView Projects (45+)
Zigbee Projects (45+)
GSM Projects (40+)
555 Timer Circuits (40+)
Sensor Projects (40+)
ARM Projects (60+)
DTMF Projects (30+)
PIC Projects (30+)
Electrical Mini Projects (25)
ESP8266 Projects (15)

KITS

Best Rgb Led Strip Light Kits

Arduino Starter Kit
Electronics Books Beginners
Breadboard Kits Beginners
Best Arduino Books
Diy Digital Clock Kits
Drone Kits Beginners
Best Brushless Motors
Raspberry Pi Books
Electronics Component Kits Beginners
Soldering Stations
Electronics Repair Tool Kit Beginners
Raspberry Pi Starter Kits
Best Waveform Generators
Arduino Robot Kits
Oscilloscope Kits Beginners
Raspberry Pi LCD Display Kits
Robot Cat Toys
FM Radio Kit Buy Online
Best Resistor Kits
Soldering Iron Kits
Best Power Supplies
Best Capacitor Kits
Arduino Sensors
Best Function Generator Kits
Led Christmas Lights
Best Iot Starter Kits
Best Gaming Headsets
Best Python Books
Best Robot Dog Toys
Best Robot Kits Kids
Best Solar Panel Kits
Led Strip Light Kits Buy Online
Top Robot Vacuum Cleaners
Digital Multimeter Kit Reviews
Solar Light Kits Beginners
Best Jumper Wire Kits
Best Gaming Earbuds
Best Wireless Routers
3d Printer Kits Buy Online
Best Gaming Mouse
Electric Lawn Mowers
Best Gaming Monitors

SUBSCRIBE FOR UPDATES

Top of Form

Enter your email address:

Bottom of Form
GENERAL

1. Tutorials
2. Symbols
3. Courses
4. Calculator
5. Contact
6. HomeZene
7. Best Arduino Kits
8. TechZene
PROJECTS

1. Electrical
2. Electronics
3. Embedded
4. Power
5. Robotics
6. ARM
7. IOT
PROJECTS

1. Mini projects
2. Microcontroller
3. Arduino
4. Solar
5. Free circuits
6. Home Automation
7. Seminar Topics
8. Electronics Questions
TUTORIALS

1. Capacitors
2. Resistors
3. Filters
4. Diodes
5. Transistors
TUTORIALS

1. Amplifiers
2. IO Devices
3. Thyristors
4. DC Circuits
5. Number System
6. TS EAMCET 2019
FOLLOW US

1. Instagram
2. Youtube
3. Facebook
4. Google Plus
5. Twitter
[footer_backtotop]
Copyright © 2019 Electronicshub.org