Sensors

Sensors on LH machines
Copyright Liebherr 2006

1. B379
1. Which working range and signal range has this

sensor?

2. How can this sensor be checked?
3. Which functions need this sensor information?
4. Which machines use this sensor?
2 sensors for LH
for B379
1. 0-400bar, 4-20mA
2. Sculi Variables: input value, measuring gauge,
messages/Analyzer
3. drive/brake-dynamik, deactivation auto ideling when
the outriggers/blade are operated (p>50bar)
reasonability of the speed sensor B259
4. all machines using the new travel motor (with Y543)
= all LS-machines of Tier4i

3 sensors for LH
2. B317
1. Which working range and signal range has this

sensor?

4. Which machines are using this sensor?
5. What must be considered when replacing the sensor?
4 sensors for LH
for B317
1. 0-180°, 4-20mA, 20-4mA

2. The S1 and S2 inputs can be checked on Sculi. The
power supply for the sensor can be measured
directly at the sensor plug.
3. Limitations and shut-off´s; (stroke limitation high,
depth, overload stop device, etc.)
4. All material handling machines for stick in cut off,
all other only if optional limitations are used.
5. After replacement the angle sensor needs to be
teached on Sculi/Wizard.

5 sensors for LH
3. B372
1. After which measuring principle, the sensor shown

operates?

4. What must be considered when replacing this
sensor?
6 sensors for LH
for B372
1. Ferromagnetic proximity switch:

switches a plus on the output, as soon
as a metal part is in front of the sensor.
2. At the sensor is a LED installed, to see
the actual condition of the output (and
also the power supply). The signal
input can be checked on Sculi.
3. end position cushioning/cut off at the
cabin lift frame
4. adjustment of the right gap between

sensor and frame (3mm – see
protocol), adjustment of the sensor
regarding his switching point
7 sensors for LH
4. B380
1. Is this temperature sensor a NTC

or a PTC?
2. How can this sensor be
checked?
3. Which functions need this

sensor information?
8 sensors for LH
for B380
1. PTC
2. measurment for the resistance
3. temperature information for the cooling/heating of
the ERC, warning if the temperature is rising to
high

9 sensors for LH
5. B314
1. Which working range and signal

range has this sensor?
3. Which functions need this sensor
information?
4. What must be considered when

replacing the sensor?
5. What changes are known at this
sensor?
10 sensors for LH
for B314
1. 0-360°, 4-20mA, 20-4mA

2. The S1 and S2 inputs can be checked on Sculi or
measured. Analyze the message stack of the Master.
The combination of messages gives you a direction
for diagnosis.
3. swing limitation, street drive position, automatic
blocking of the auxillary axle when turning the
uppercariage, overload stop device, overload
warning, virtual wall, automatic swing brake,
4. After replacement the sensor needs to be teached.

5. SI for the B314, after some updates this sensor
needs to be teached also
11 sensors for LH
6. B318
1. Which working range and

signal range has this sensor?
checked?
3. Which functions need this
sensor information?

4. Must be something special to
be observed when replacing
this sensor?
12 sensors for LH
for B318
1. 0-400bar, 4-20mA
2. Check the input on Sculi, compare with the real
pressure value
3. monitoring boom, overload warning, overload
warning switchable, overload stop device, boom
pressureless down,
4. Plug & Play, after the pressure of the hoist cylinders
was discharged

13 sensors for LH
7. B359
1. Which working range and signal range has this sensor?


4. Must be something special to be observed when
replacing this sensor?
14 sensors for LH
for B359
1. 0-60bar, 4-20mA
2. check the input on Sculi, prove by the real pressure
value
3. Grab Control
4. Plug & Play

15 sensors for LH
8. B44
LP off 2bar
HP off 28bar


3. Must the refrigerant be sucked for an exchange of the
sensor?
4. Is this sensor observed/monitored from master?
16 sensors for LH
for B44
1. protection of the aircondition device
2. check the input on Sculi, prove by his normal condition
@ the current pressure
3. yes
4. yes

17 sensors for LH
9. B259
1. Which kind of signal is given

by this sensor?
checked?
3. If the sensor is checked by
the machine control during
the operation?

18 sensors for LH
for B259
1. frequency [cnt]
2. check, if the speed information in Wizard is plausible,
or not
3. Yes. With the informations pump pressure (load
information), position travel pedal (speed setpoint)
and the current gear (first or second) is the speed
information from B259 proved during travel
operation.
4. Speedometer on display, Monitoring vehicle speed,
automatic brake, adjustment of the travel speed on

Wizard,
19 sensors for LH
10. B315


4. Which machines use this sensor?
5. What must be considered when replacing the sensor?
20 sensors for LH
for B315
1. 0-180°, 4-20mA, 20-4mA

2. The S1 and S2 inputs can be checked on Sculi. The
power supply for the sensor can be measured
directly at the sensor plug.
3. Limitations for the working range of the machine.
(stroke, limitation, overload warning, overload stop
device, virtual wall, etc.)
4. All LH with overload warning device, or if limitations
are used.
5. After replacement this sensor needs to be teached

on Wizard.
21 sensors for LH
11. A185
1. With which voltage is the shown
sensor supplied?
2. What is the easiest way to check
this sensor?
3. What needs to be ovserved
during replacement?
4. Which funtions can this input be
used for?
5. Which kind and diaposone of
signal is given by this sensor?

22 sensors for LH
for A185
1. 5V power supply
2. Display > Info Inputs > check the input information,
check the inputs on Sculi
3. Nothing, Plug & Play for replacement
4. see AnalogShunter, exception: cabin lift, joystick
steering, standard: grapple rotation
5. voltage signal: 0,5 - 4,5V, neutral: 2,5V

23 sensors for LH
for A185: input signals on Sculi
neutral
applied left
applied right

24 sensors for LH
12. B326

2. What is the easiest way to check this sensor?

3. How are the input variables named?
4. Is there something to observe during replacement?
25 sensors for LH
for B326
1. approx. 30° of actuation, 4-20mA, 20-4mA

2. Display > Info Inputs > check it´s condition, exchange
the travel pedal with a pedal of the rising boom, if used
3. %ID4.47.3 and %ID4.45.3
4. No, Plug & Play

26 sensors for LH

Sensors

Uploaded by

Copyright:

Available Formats

Sensors

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sensors

Uploaded by

Copyright:

Available Formats

Sensors on LH machines

Copyright Liebherr 2006

1. Which working range and signal range has this

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which working range and signal range has this

Copyright Liebherr 2006

1. 0-180°, 4-20mA, 20-4mA

Copyright Liebherr 2006

1. After which measuring principle, the sensor shown

Copyright Liebherr 2006

1. Ferromagnetic proximity switch:

Copyright Liebherr 2006

1. Is this temperature sensor a NTC

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which working range and signal

Copyright Liebherr 2006

1. 0-360°, 4-20mA, 20-4mA

Copyright Liebherr 2006

1. Which working range and

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which working range and signal range has this sensor?

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which functions need this sensor information?

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which kind of signal is given

4. Which functions need this sensor information?

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which working range and signal range has this sensor?

Copyright Liebherr 2006

1. 0-180°, 4-20mA, 20-4mA

Copyright Liebherr 2006

Copyright Liebherr 2006

Copyright Liebherr 2006

Copyright Liebherr 2006

1. Which working range and signal range has this sensor?

Copyright Liebherr 2006

1. approx. 30° of actuation, 4-20mA, 20-4mA

Copyright Liebherr 2006

You might also like