Scribd Logo
Upload

Welcome to Scribd!

  • 62 views

    9.2.1.11 Packet Tracer - Configuring Named Standard ACLs Instructions

    Uploaded by

    IVA
    CISCO LAB 1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    9.2.1.11 Packet Tracer - Configuring Named Standard ACLs Instructions

    Uploaded by

    IVA
    62 views2 pages
    CISCO LAB 1

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    CISCO LAB 1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    62 views2 pages

    9.2.1.11 Packet Tracer - Configuring Named Standard ACLs Instructions

    Uploaded by

    IVA
    CISCO LAB 1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Packet Tracer - Configuring Named Standard ACLs

    Topology

    Addressing Table

    Device Interface IP Address Subnet Mask Default Gateway

    F0/0 192.168.10.1 255.255.255.0 N/A


    F0/1 192.168.20.1 255.255.255.0 N/A
    R1
    E0/0/0 192.168.100.1 255.255.255.0 N/A
    E0/1/0 192.168.200.1 255.255.255.0 N/A
    File Server NIC 192.168.200.100 255.255.255.0 192.168.200.1
    Web Server NIC 192.168.100.100 255.255.255.0 192.168.100.1
    PC0 NIC 192.168.20.3 255.255.255.0 192.168.20.1
    PC1 NIC 192.168.20.4 255.255.255.0 192.168.20.1
    PC2 NIC 192.168.10.3 255.255.255.0 192.168.10.1

    Objectives
    Part 1: Configure and Apply a Named Standard ACL
    Part 2: Verify the ACL Implementation

    Background / Scenario
    The senior network administrator has tasked you to create a standard named ACL to prevent access to a file
    server. All clients from one network and one specific workstation from a different network should be denied
    access.

    © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 2
    Packet Tracer - Configuring Named Standard ACLs

    Part 1: Configure and Apply a Named Standard ACL


    Step 1: Verify connectivity before the ACL is configured and applied.
    All three workstations should be able to ping both the Web Server and File Server.

    Step 2: Configure a named standard ACL.


    Configure the following named ACL on R1.
    R1(config)# ip access-list standard File_Server_Restrictions
    R1(config-std-nacl)# permit host 192.168.20.4
    R1(config-std-nacl)# deny any
    Note: For scoring purposes, the ACL name is case-sensitive.

    Step 3: Apply the named ACL.


    a. Apply the ACL outbound on the interface Fast Ethernet 0/1.
    R1(config-if)# ip access-group File_Server_Restrictions out
    b. Save the configuration.

    Part 2: Verify the ACL Implementation


    Step 1: Verify the ACL configuration and application to the interface.
    Use the show access-lists command to verify the ACL configuration. Use the show run or show ip
    interface fastethernet 0/1 command to verify that the ACL is applied correctly to the interface.

    Step 2: Verify that the ACL is working properly.


    All three workstations should be able to ping the Web Server, but only PC1 should be able to ping the File
    Server.

    © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 2

    You might also like